From mboxrd@z Thu Jan 1 00:00:00 1970 From: Stephen Boyd Subject: [PATCH v5 20/23] usb: chipidea: msm: Handle phy power states Date: Mon, 17 Oct 2016 18:56:33 -0700 Message-ID: <20161018015636.11701-21-stephen.boyd@linaro.org> References: <20161018015636.11701-1-stephen.boyd@linaro.org> Return-path: In-Reply-To: <20161018015636.11701-1-stephen.boyd-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org> Sender: linux-usb-owner-u79uwXL29TY76Z2rM5mHXA@public.gmane.org To: linux-usb-u79uwXL29TY76Z2rM5mHXA@public.gmane.org Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org, linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-arm-msm-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Andy Gross , Bjorn Andersson , Neil Armstrong , Arnd Bergmann , Felipe Balbi , Peter Chen , Greg Kroah-Hartman List-Id: linux-arm-msm@vger.kernel.org The ULPI phy on qcom platforms needs to be initialized and powered on after a USB reset and before we toggle the run/stop bit. Otherwise, the phy locks up and doesn't work properly. Hook the phy initialization into the RESET event and the phy power off into the STOPPED event. Acked-by: Peter Chen Cc: Greg Kroah-Hartman Signed-off-by: Stephen Boyd --- drivers/usb/chipidea/ci_hdrc_msm.c | 40 +++++++++++++++++++------------------- drivers/usb/chipidea/core.c | 8 ++++++-- drivers/usb/chipidea/host.c | 8 ++++++-- include/linux/usb/chipidea.h | 2 +- 4 files changed, 33 insertions(+), 25 deletions(-) diff --git a/drivers/usb/chipidea/ci_hdrc_msm.c b/drivers/usb/chipidea/ci_hdrc_msm.c index fe96df7b530c..316044dba0ac 100644 --- a/drivers/usb/chipidea/ci_hdrc_msm.c +++ b/drivers/usb/chipidea/ci_hdrc_msm.c @@ -80,20 +80,33 @@ static const struct reset_control_ops ci_hdrc_msm_reset_ops = { .reset = ci_hdrc_msm_por_reset, }; -static void ci_hdrc_msm_notify_event(struct ci_hdrc *ci, unsigned event) +static int ci_hdrc_msm_notify_event(struct ci_hdrc *ci, unsigned event) { struct device *dev = ci->dev->parent; struct ci_hdrc_msm *msm_ci = dev_get_drvdata(dev); + int ret; switch (event) { case CI_HDRC_CONTROLLER_RESET_EVENT: dev_dbg(dev, "CI_HDRC_CONTROLLER_RESET_EVENT received\n"); + + hw_phymode_configure(ci); if (msm_ci->secondary_phy) { u32 val = readl_relaxed(msm_ci->base + HS_PHY_SEC_CTRL); val |= HS_PHY_DIG_CLAMP_N; writel_relaxed(val, msm_ci->base + HS_PHY_SEC_CTRL); } + ret = phy_init(ci->phy); + if (ret) + return ret; + + ret = phy_power_on(ci->phy); + if (ret) { + phy_exit(ci->phy); + return ret; + } + /* use AHB transactor, allow posted data writes */ hw_write_id_reg(ci, HS_PHY_AHB_MODE, 0xffffffff, 0x8); @@ -113,21 +126,18 @@ static void ci_hdrc_msm_notify_event(struct ci_hdrc *ci, unsigned event) HSPHY_SESS_VLD_CTRL); } - - usb_phy_init(ci->usb_phy); break; case CI_HDRC_CONTROLLER_STOPPED_EVENT: dev_dbg(dev, "CI_HDRC_CONTROLLER_STOPPED_EVENT received\n"); - /* - * Put the phy in non-driving mode. Otherwise host - * may not detect soft-disconnection. - */ - usb_phy_notify_disconnect(ci->usb_phy, USB_SPEED_UNKNOWN); + phy_power_off(ci->phy); + phy_exit(ci->phy); break; default: dev_dbg(dev, "unknown ci_hdrc event\n"); break; } + + return 0; } static int ci_hdrc_msm_mux_phy(struct ci_hdrc_msm *ci, @@ -167,7 +177,6 @@ static int ci_hdrc_msm_probe(struct platform_device *pdev) { struct ci_hdrc_msm *ci; struct platform_device *plat_ci; - struct usb_phy *phy; struct clk *clk; struct reset_control *reset; struct resource *res; @@ -181,21 +190,12 @@ static int ci_hdrc_msm_probe(struct platform_device *pdev) return -ENOMEM; platform_set_drvdata(pdev, ci); - /* - * OTG(PHY) driver takes care of PHY initialization, clock management, - * powering up VBUS, mapping of registers address space and power - * management. - */ - phy = devm_usb_get_phy_by_phandle(&pdev->dev, "usb-phy", 0); - if (IS_ERR(phy)) - return PTR_ERR(phy); - ci->pdata.name = "ci_hdrc_msm"; ci->pdata.capoffset = DEF_CAPOFFSET; ci->pdata.flags = CI_HDRC_REGS_SHARED | CI_HDRC_DISABLE_STREAMING | - CI_HDRC_OVERRIDE_AHB_BURST; + CI_HDRC_OVERRIDE_AHB_BURST | + CI_HDRC_OVERRIDE_PHY_CONTROL; ci->pdata.notify_event = ci_hdrc_msm_notify_event; - ci->pdata.usb_phy = phy; reset = devm_reset_control_get(&pdev->dev, "core"); if (IS_ERR(reset)) diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c index d1ae9a03e0fa..fbef1c961572 100644 --- a/drivers/usb/chipidea/core.c +++ b/drivers/usb/chipidea/core.c @@ -327,6 +327,7 @@ void hw_phymode_configure(struct ci_hdrc *ci) hw_write(ci, OP_PORTSC, PORTSC_STS, PORTSC_STS); } } +EXPORT_SYMBOL_GPL(hw_phymode_configure); /** * _ci_usb_phy_init: initialize phy taking in account both phy and usb_phy @@ -503,9 +504,12 @@ int hw_device_reset(struct ci_hdrc *ci) return ret; } - if (ci->platdata->notify_event) - ci->platdata->notify_event(ci, + if (ci->platdata->notify_event) { + ret = ci->platdata->notify_event(ci, CI_HDRC_CONTROLLER_RESET_EVENT); + if (ret) + return ret; + } /* USBMODE should be configured step by step */ hw_write(ci, OP_USBMODE, USBMODE_CM, USBMODE_CM_IDLE); diff --git a/drivers/usb/chipidea/host.c b/drivers/usb/chipidea/host.c index f036a9e39ced..bbfb9e62d49d 100644 --- a/drivers/usb/chipidea/host.c +++ b/drivers/usb/chipidea/host.c @@ -90,8 +90,12 @@ static int ehci_ci_reset(struct usb_hcd *hcd) ehci->need_io_watchdog = 0; - if (ci->platdata->notify_event) - ci->platdata->notify_event(ci, CI_HDRC_CONTROLLER_RESET_EVENT); + if (ci->platdata->notify_event) { + ret = ci->platdata->notify_event(ci, + CI_HDRC_CONTROLLER_RESET_EVENT); + if (ret) + return ret; + } ci_platform_configure(ci); diff --git a/include/linux/usb/chipidea.h b/include/linux/usb/chipidea.h index 7e3daa37cf60..c5fdfcf99828 100644 --- a/include/linux/usb/chipidea.h +++ b/include/linux/usb/chipidea.h @@ -61,7 +61,7 @@ struct ci_hdrc_platform_data { enum usb_dr_mode dr_mode; #define CI_HDRC_CONTROLLER_RESET_EVENT 0 #define CI_HDRC_CONTROLLER_STOPPED_EVENT 1 - void (*notify_event) (struct ci_hdrc *ci, unsigned event); + int (*notify_event) (struct ci_hdrc *ci, unsigned event); struct regulator *reg_vbus; struct usb_otg_caps ci_otg_caps; bool tpl_support; -- 2.10.0.297.gf6727b0 -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html