From mboxrd@z Thu Jan 1 00:00:00 1970 From: Jorge Ramirez-Ortiz Subject: [PATCH v4 1/4] dt-bindings: phy: remove qcom-dwc3-usb-phy Date: Thu, 7 Feb 2019 12:17:31 +0100 Message-ID: <20190207111734.24171-2-jorge.ramirez-ortiz@linaro.org> References: <20190207111734.24171-1-jorge.ramirez-ortiz@linaro.org> Mime-Version: 1.0 Content-Transfer-Encoding: 8bit Return-path: In-Reply-To: <20190207111734.24171-1-jorge.ramirez-ortiz@linaro.org> Sender: linux-kernel-owner@vger.kernel.org To: jorge.ramirez-ortiz@linaro.org, robh@kernel.org, bjorn.andersson@linaro.org Cc: swboyd@chromium.org, andy.gross@linaro.org, shawn.guo@linaro.org, gregkh@linuxfoundation.org, mark.rutland@arm.com, kishon@ti.com, jackp@codeaurora.org, devicetree@vger.kernel.org, linux-arm-msm@vger.kernel.org, linux-usb@vger.kernel.org, linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org, khasim.mohammed@linaro.org List-Id: linux-arm-msm@vger.kernel.org This binding is not used by any driver. Signed-off-by: Jorge Ramirez-Ortiz --- .../bindings/phy/qcom-dwc3-usb-phy.txt | 37 ------------------- 1 file changed, 37 deletions(-) delete mode 100644 Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt diff --git a/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt b/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt deleted file mode 100644 index a1697c27aecd..000000000000 --- a/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt +++ /dev/null @@ -1,37 +0,0 @@ -Qualcomm DWC3 HS AND SS PHY CONTROLLER --------------------------------------- - -DWC3 PHY nodes are defined to describe on-chip Synopsis Physical layer -controllers. Each DWC3 PHY controller should have its own node. - -Required properties: -- compatible: should contain one of the following: - - "qcom,dwc3-hs-usb-phy" for High Speed Synopsis PHY controller - - "qcom,dwc3-ss-usb-phy" for Super Speed Synopsis PHY controller -- reg: offset and length of the DWC3 PHY controller register set -- #phy-cells: must be zero -- clocks: a list of phandles and clock-specifier pairs, one for each entry in - clock-names. -- clock-names: Should contain "ref" for the PHY reference clock - -Optional clocks: - "xo" External reference clock - -Example: - phy@100f8800 { - compatible = "qcom,dwc3-hs-usb-phy"; - reg = <0x100f8800 0x30>; - clocks = <&gcc USB30_0_UTMI_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - }; - - phy@100f8830 { - compatible = "qcom,dwc3-ss-usb-phy"; - reg = <0x100f8830 0x30>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - }; -- 2.20.1