[PATCH v2 0/7] PM8005 and PMS405 regulator support

[PATCH v2 0/7] PM8005 and PMS405 regulator support

[Jeffrey Hugo]

The MSM8998 MTP reference platform supplies VDD_GFX from s1 of the
pm8005 PMIC.  VDD_GFX is needed to turn on the GPU.  As we are looking
to bring up the GPU, add the support for pm8005 and wire up s1 in a
basic manner so that we have this dependency out of the way and can
focus on enabling the GPU driver.

The s3 regulator of PMS405 is used for voltage scaling of the CPU on
QCS404.

Both PMICs are very similar in deisgn, so add the base support with one,
and trivially add the support for the other on top.

The PMS405 work has only been compile tested as I don't have the proper
platform.  A tested-by from Jorge or someone with the platform would be
great.

v2:
-Perform if statement cleanups per review discussion
-Pull in linear range support since its related, and simple
-Rework the PM8005 to minimize special cases in the driver
-"common2" is now ftsmps426 since that design first implemented it
-Reworked the PMS405 changes on top, since they are related to pm8005 and
trivial

Jeffrey Hugo (4):
  drivers: regulator: qcom_spmi: Refactor get_mode/set_mode
  dt-bindings: qcom_spmi: Document PM8005 regulators
  regulator: qcom_spmi: Add support for PM8005
  arm64: dts: msm8998-mtp: Add pm8005_s1 regulator

Jorge Ramirez (2):
  dt-bindings: qcom_spmi: Document pms405 support
  drivers: regulator: qcom: add PMS405 SPMI regulator

Jorge Ramirez-Ortiz (1):
  drivers: regulator: qcom_spmi: enable linear range info

 .../regulator/qcom,spmi-regulator.txt         |  28 +++
 arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi     |  17 ++
 drivers/regulator/qcom_spmi-regulator.c       | 233 +++++++++++++++++-
 3 files changed, 271 insertions(+), 7 deletions(-)

-- 
2.17.1

[PATCH v2 1/7] drivers: regulator: qcom_spmi: enable linear range info

[Jeffrey Hugo]

From: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
---
 drivers/regulator/qcom_spmi-regulator.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index 53a61fb65642..fd55438c25d6 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -1744,6 +1744,7 @@ MODULE_DEVICE_TABLE(of, qcom_spmi_regulator_match);
 static int qcom_spmi_regulator_probe(struct platform_device *pdev)
 {
 	const struct spmi_regulator_data *reg;
+	const struct spmi_voltage_range *range;
 	const struct of_device_id *match;
 	struct regulator_config config = { };
 	struct regulator_dev *rdev;
@@ -1833,6 +1834,12 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
 			}
 		}
 
+		if (vreg->logical_type == SPMI_REGULATOR_LOGICAL_TYPE_HFS430) {
+			/* since there is only one range */
+			range = spmi_regulator_find_range(vreg);
+			vreg->desc.uV_step = range->step_uV;
+		}
+
 		config.dev = dev;
 		config.driver_data = vreg;
 		config.regmap = regmap;
-- 
2.17.1

[PATCH v2 2/7] drivers: regulator: qcom_spmi: Refactor get_mode/set_mode

[Jeffrey Hugo]

spmi_regulator_common_get_mode and spmi_regulator_common_set_mode use
multi-level ifs which mirror a switch statement.  Refactor to use a switch
statement to make the code flow more clear.

Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
---
 drivers/regulator/qcom_spmi-regulator.c | 28 ++++++++++++++++---------
 1 file changed, 18 insertions(+), 10 deletions(-)

diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index fd55438c25d6..1c18fe5969b5 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -911,13 +911,14 @@ static unsigned int spmi_regulator_common_get_mode(struct regulator_dev *rdev)
 
 	spmi_vreg_read(vreg, SPMI_COMMON_REG_MODE, &reg, 1);
 
-	if (reg & SPMI_COMMON_MODE_HPM_MASK)
+	switch (reg) {
+	case SPMI_COMMON_MODE_HPM_MASK:
 		return REGULATOR_MODE_NORMAL;
-
-	if (reg & SPMI_COMMON_MODE_AUTO_MASK)
+	case SPMI_COMMON_MODE_AUTO_MASK:
 		return REGULATOR_MODE_FAST;
-
-	return REGULATOR_MODE_IDLE;
+	default:
+		return REGULATOR_MODE_IDLE;
+	}
 }
 
 static int
@@ -925,12 +926,19 @@ spmi_regulator_common_set_mode(struct regulator_dev *rdev, unsigned int mode)
 {
 	struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
 	u8 mask = SPMI_COMMON_MODE_HPM_MASK | SPMI_COMMON_MODE_AUTO_MASK;
-	u8 val = 0;
+	u8 val;
 
-	if (mode == REGULATOR_MODE_NORMAL)
+	switch (mode) {
+	case REGULATOR_MODE_NORMAL:
 		val = SPMI_COMMON_MODE_HPM_MASK;
-	else if (mode == REGULATOR_MODE_FAST)
+		break;
+	case REGULATOR_MODE_FAST:
 		val = SPMI_COMMON_MODE_AUTO_MASK;
+		break;
+	default:
+		val = 0;
+		break;
+	}
 
 	return spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_MODE, val, mask);
 }
@@ -1834,9 +1842,9 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
 			}
 		}
 
-		if (vreg->logical_type == SPMI_REGULATOR_LOGICAL_TYPE_HFS430) {
+		if (vreg->set_points->count == 1) {
 			/* since there is only one range */
-			range = spmi_regulator_find_range(vreg);
+			range = vreg->set_points->range;
 			vreg->desc.uV_step = range->step_uV;
 		}
 
-- 
2.17.1

[PATCH v2 3/7] dt-bindings: qcom_spmi: Document PM8005 regulators

[Jeffrey Hugo]

Document the dt bindings for the PM8005 regulators which are usually used
for VDD of standalone blocks on a SoC like the GPU.

Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
 .../devicetree/bindings/regulator/qcom,spmi-regulator.txt     | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
index 406f2e570c50..ba94bc2d407a 100644
--- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
@@ -4,6 +4,7 @@ Qualcomm SPMI Regulators
 	Usage: required
 	Value type: <string>
 	Definition: must be one of:
+			"qcom,pm8005-regulators"
 			"qcom,pm8841-regulators"
 			"qcom,pm8916-regulators"
 			"qcom,pm8941-regulators"
@@ -120,6 +121,9 @@ The regulator node houses sub-nodes for each regulator within the device. Each
 sub-node is identified using the node's name, with valid values listed for each
 of the PMICs below.
 
+pm8005:
+	s1, s2, s3, s4
+
 pm8841:
 	s1, s2, s3, s4, s5, s6, s7, s8
 
-- 
2.17.1

[PATCH v2 4/7] regulator: qcom_spmi: Add support for PM8005

[Jeffrey Hugo]

The PM8005 is used on the msm8998 MTP.  The S1 regulator is VDD_GFX, ie
it needs to be on and controlled inorder to use the GPU.  Add support to
drive the PM8005 regulators so that we can bring up the GPU on msm8998.

Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
---
 drivers/regulator/qcom_spmi-regulator.c | 169 ++++++++++++++++++++++++
 1 file changed, 169 insertions(+)

diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index 1c18fe5969b5..c7880c1d4bcd 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -104,6 +104,7 @@ enum spmi_regulator_logical_type {
 	SPMI_REGULATOR_LOGICAL_TYPE_ULT_LO_SMPS,
 	SPMI_REGULATOR_LOGICAL_TYPE_ULT_HO_SMPS,
 	SPMI_REGULATOR_LOGICAL_TYPE_ULT_LDO,
+	SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS426,
 };
 
 enum spmi_regulator_type {
@@ -150,6 +151,7 @@ enum spmi_regulator_subtype {
 	SPMI_REGULATOR_SUBTYPE_5V_BOOST		= 0x01,
 	SPMI_REGULATOR_SUBTYPE_FTS_CTL		= 0x08,
 	SPMI_REGULATOR_SUBTYPE_FTS2p5_CTL	= 0x09,
+	SPMI_REGULATOR_SUBTYPE_FTS426_CTL	= 0x0a,
 	SPMI_REGULATOR_SUBTYPE_BB_2A		= 0x01,
 	SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL1	= 0x0d,
 	SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL2	= 0x0e,
@@ -170,6 +172,18 @@ enum spmi_common_regulator_registers {
 	SPMI_COMMON_REG_STEP_CTRL		= 0x61,
 };
 
+/*
+ * Second common register layout used by newer devices starting with ftsmps426
+ * Note that some of the registers from the first common layout remain
+ * unchanged and their definition is not duplicated.
+ */
+enum spmi_ftsmps426_regulator_registers {
+	SPMI_FTSMPS426_REG_VOLTAGE_LSB		= 0x40,
+	SPMI_FTSMPS426_REG_VOLTAGE_MSB		= 0x41,
+	SPMI_FTSMPS426_REG_VOLTAGE_ULS_LSB	= 0x68,
+	SPMI_FTSMPS426_REG_VOLTAGE_ULS_MSB	= 0x69,
+};
+
 enum spmi_vs_registers {
 	SPMI_VS_REG_OCP				= 0x4a,
 	SPMI_VS_REG_SOFT_START			= 0x4c,
@@ -229,6 +243,14 @@ enum spmi_common_control_register_index {
 #define SPMI_COMMON_MODE_FOLLOW_HW_EN0_MASK	0x01
 #define SPMI_COMMON_MODE_FOLLOW_ALL_MASK	0x1f
 
+#define SPMI_FTSMPS426_MODE_BYPASS_MASK		3
+#define SPMI_FTSMPS426_MODE_RETENTION_MASK	4
+#define SPMI_FTSMPS426_MODE_LPM_MASK		5
+#define SPMI_FTSMPS426_MODE_AUTO_MASK		6
+#define SPMI_FTSMPS426_MODE_HPM_MASK		7
+
+#define SPMI_FTSMPS426_MODE_MASK		0x07
+
 /* Common regulator pull down control register layout */
 #define SPMI_COMMON_PULL_DOWN_ENABLE_MASK	0x80
 
@@ -274,6 +296,23 @@ enum spmi_common_control_register_index {
 #define SPMI_FTSMPS_STEP_MARGIN_NUM	4
 #define SPMI_FTSMPS_STEP_MARGIN_DEN	5
 
+#define SPMI_FTSMPS426_STEP_CTRL_DELAY_MASK	0x03
+#define SPMI_FTSMPS426_STEP_CTRL_DELAY_SHIFT	0
+
+/* Clock rate in kHz of the FTSMPS426 regulator reference clock. */
+#define SPMI_FTSMPS426_CLOCK_RATE		4800
+
+/* Minimum voltage stepper delay for each step. */
+#define SPMI_FTSMPS426_STEP_DELAY		2
+
+/*
+ * The ratio SPMI_FTSMPS426_STEP_MARGIN_NUM/SPMI_FTSMPS426_STEP_MARGIN_DEN is
+ * used to adjust the step rate in order to account for oscillator variance.
+ */
+#define SPMI_FTSMPS426_STEP_MARGIN_NUM	10
+#define SPMI_FTSMPS426_STEP_MARGIN_DEN	11
+
+
 /* VSET value to decide the range of ULT SMPS */
 #define ULT_SMPS_RANGE_SPLIT 0x60
 
@@ -447,6 +486,10 @@ static struct spmi_voltage_range ftsmps2p5_ranges[] = {
 	SPMI_VOLTAGE_RANGE(1,  160000, 1360000, 2200000, 2200000, 10000),
 };
 
+static struct spmi_voltage_range ftsmps426_ranges[] = {
+	SPMI_VOLTAGE_RANGE(0,       0,  320000, 1352000, 1352000,  4000),
+};
+
 static struct spmi_voltage_range boost_ranges[] = {
 	SPMI_VOLTAGE_RANGE(0, 4000000, 4000000, 5550000, 5550000, 50000),
 };
@@ -480,6 +523,7 @@ static DEFINE_SPMI_SET_POINTS(ln_ldo);
 static DEFINE_SPMI_SET_POINTS(smps);
 static DEFINE_SPMI_SET_POINTS(ftsmps);
 static DEFINE_SPMI_SET_POINTS(ftsmps2p5);
+static DEFINE_SPMI_SET_POINTS(ftsmps426);
 static DEFINE_SPMI_SET_POINTS(boost);
 static DEFINE_SPMI_SET_POINTS(boost_byp);
 static DEFINE_SPMI_SET_POINTS(ult_lo_smps);
@@ -747,6 +791,23 @@ spmi_regulator_common_set_voltage(struct regulator_dev *rdev, unsigned selector)
 	return spmi_vreg_write(vreg, SPMI_COMMON_REG_VOLTAGE_RANGE, buf, 2);
 }
 
+static int spmi_regulator_common_list_voltage(struct regulator_dev *rdev,
+					      unsigned selector);
+
+static int spmi_regulator_ftsmps426_set_voltage(struct regulator_dev *rdev,
+					      unsigned selector)
+{
+	struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+	u8 buf[2];
+	int mV;
+
+	mV = spmi_regulator_common_list_voltage(rdev, selector) / 1000;
+
+	buf[0] = mV & 0xff;
+	buf[1] = mV >> 8;
+	return spmi_vreg_write(vreg, SPMI_FTSMPS426_REG_VOLTAGE_LSB, buf, 2);
+}
+
 static int spmi_regulator_set_voltage_time_sel(struct regulator_dev *rdev,
 		unsigned int old_selector, unsigned int new_selector)
 {
@@ -778,6 +839,16 @@ static int spmi_regulator_common_get_voltage(struct regulator_dev *rdev)
 	return spmi_hw_selector_to_sw(vreg, voltage_sel, range);
 }
 
+static int spmi_regulator_ftsmps426_get_voltage(struct regulator_dev *rdev)
+{
+	struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+	u8 buf[2];
+
+	spmi_vreg_read(vreg, SPMI_FTSMPS426_REG_VOLTAGE_LSB, buf, 2);
+
+	return (((unsigned int)buf[1] << 8) | (unsigned int)buf[0]) * 1000;
+}
+
 static int spmi_regulator_single_map_voltage(struct regulator_dev *rdev,
 		int min_uV, int max_uV)
 {
@@ -921,6 +992,23 @@ static unsigned int spmi_regulator_common_get_mode(struct regulator_dev *rdev)
 	}
 }
 
+static unsigned int spmi_regulator_ftsmps426_get_mode(struct regulator_dev *rdev)
+{
+	struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+	u8 reg;
+
+	spmi_vreg_read(vreg, SPMI_COMMON_REG_MODE, &reg, 1);
+
+	switch (reg) {
+	case SPMI_FTSMPS426_MODE_HPM_MASK:
+		return REGULATOR_MODE_NORMAL;
+	case SPMI_FTSMPS426_MODE_AUTO_MASK:
+		return REGULATOR_MODE_FAST;
+	default:
+		return REGULATOR_MODE_IDLE;
+	}
+}
+
 static int
 spmi_regulator_common_set_mode(struct regulator_dev *rdev, unsigned int mode)
 {
@@ -943,6 +1031,28 @@ spmi_regulator_common_set_mode(struct regulator_dev *rdev, unsigned int mode)
 	return spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_MODE, val, mask);
 }
 
+static int
+spmi_regulator_ftsmps426_set_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+	struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+	u8 mask = SPMI_FTSMPS426_MODE_MASK;
+	u8 val;
+
+	switch (mode) {
+	case REGULATOR_MODE_NORMAL:
+		val = SPMI_FTSMPS426_MODE_HPM_MASK;
+		break;
+	case REGULATOR_MODE_FAST:
+		val = SPMI_FTSMPS426_MODE_AUTO_MASK;
+		break;
+	default:
+		val = SPMI_FTSMPS426_MODE_LPM_MASK;
+		break;
+	}
+
+	return spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_MODE, val, mask);
+}
+
 static int
 spmi_regulator_common_set_load(struct regulator_dev *rdev, int load_uA)
 {
@@ -1272,6 +1382,21 @@ static struct regulator_ops spmi_ult_ldo_ops = {
 	.set_soft_start		= spmi_regulator_common_set_soft_start,
 };
 
+static struct regulator_ops spmi_ftsmps426_ops = {
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.is_enabled		= regulator_is_enabled_regmap,
+	.set_voltage_sel	= spmi_regulator_ftsmps426_set_voltage,
+	.set_voltage_time_sel	= spmi_regulator_set_voltage_time_sel,
+	.get_voltage		= spmi_regulator_ftsmps426_get_voltage,
+	.map_voltage		= spmi_regulator_single_map_voltage,
+	.list_voltage		= spmi_regulator_common_list_voltage,
+	.set_mode		= spmi_regulator_ftsmps426_set_mode,
+	.get_mode		= spmi_regulator_ftsmps426_get_mode,
+	.set_load		= spmi_regulator_common_set_load,
+	.set_pull_down		= spmi_regulator_common_set_pull_down,
+};
+
 /* Maximum possible digital major revision value */
 #define INF 0xFF
 
@@ -1307,6 +1432,7 @@ static const struct spmi_regulator_mapping supported_regulators[] = {
 	SPMI_VREG(BOOST, 5V_BOOST, 0, INF, BOOST,  boost,  boost,       0),
 	SPMI_VREG(FTS,   FTS_CTL,  0, INF, FTSMPS, ftsmps, ftsmps, 100000),
 	SPMI_VREG(FTS, FTS2p5_CTL, 0, INF, FTSMPS, ftsmps, ftsmps2p5, 100000),
+	SPMI_VREG(FTS, FTS426_CTL, 0, INF, FTSMPS426, ftsmps426, ftsmps426, 100000),
 	SPMI_VREG(BOOST_BYP, BB_2A, 0, INF, BOOST_BYP, boost, boost_byp, 0),
 	SPMI_VREG(ULT_BUCK, ULT_HF_CTL1, 0, INF, ULT_LO_SMPS, ult_lo_smps,
 						ult_lo_smps,   100000),
@@ -1444,6 +1570,34 @@ static int spmi_regulator_init_slew_rate(struct spmi_regulator *vreg)
 	return ret;
 }
 
+static int spmi_regulator_init_slew_rate_ftsmps426(struct spmi_regulator *vreg)
+{
+	int ret;
+	u8 reg = 0;
+	int delay, slew_rate;
+	const struct spmi_voltage_range *range = &vreg->set_points->range[0];
+
+	ret = spmi_vreg_read(vreg, SPMI_COMMON_REG_STEP_CTRL, &reg, 1);
+	if (ret) {
+		dev_err(vreg->dev, "spmi read failed, ret=%d\n", ret);
+		return ret;
+	}
+
+	delay = reg & SPMI_FTSMPS426_STEP_CTRL_DELAY_MASK;
+	delay >>= SPMI_FTSMPS426_STEP_CTRL_DELAY_SHIFT;
+
+	/* slew_rate has units of uV/us */
+	slew_rate = SPMI_FTSMPS426_CLOCK_RATE * range->step_uV;
+	slew_rate /= 1000 * (SPMI_FTSMPS426_STEP_DELAY << delay);
+	slew_rate *= SPMI_FTSMPS426_STEP_MARGIN_NUM;
+	slew_rate /= SPMI_FTSMPS426_STEP_MARGIN_DEN;
+
+	/* Ensure that the slew rate is greater than 0 */
+	vreg->slew_rate = max(slew_rate, 1);
+
+	return ret;
+}
+
 static int spmi_regulator_init_registers(struct spmi_regulator *vreg,
 				const struct spmi_regulator_init_data *data)
 {
@@ -1583,6 +1737,12 @@ static int spmi_regulator_of_parse(struct device_node *node,
 		ret = spmi_regulator_init_slew_rate(vreg);
 		if (ret)
 			return ret;
+		break;
+	case SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS426:
+		ret = spmi_regulator_init_slew_rate_ftsmps426(vreg);
+		if (ret)
+			return ret;
+		break;
 	default:
 		break;
 	}
@@ -1739,7 +1899,16 @@ static const struct spmi_regulator_data pmi8994_regulators[] = {
 	{ }
 };
 
+static const struct spmi_regulator_data pm8005_regulators[] = {
+	{ "s1", 0x1400, "vdd_s1", },
+	{ "s2", 0x1700, "vdd_s2", },
+	{ "s3", 0x1a00, "vdd_s3", },
+	{ "s4", 0x1d00, "vdd_s4", },
+	{ }
+};
+
 static const struct of_device_id qcom_spmi_regulator_match[] = {
+	{ .compatible = "qcom,pm8005-regulators", .data = &pm8005_regulators },
 	{ .compatible = "qcom,pm8841-regulators", .data = &pm8841_regulators },
 	{ .compatible = "qcom,pm8916-regulators", .data = &pm8916_regulators },
 	{ .compatible = "qcom,pm8941-regulators", .data = &pm8941_regulators },
-- 
2.17.1

[PATCH v2 5/7] arm64: dts: msm8998-mtp: Add pm8005_s1 regulator

[Jeffrey Hugo]

The pm8005_s1 is VDD_GFX, and needs to be on to enable the GPU.
This should be hooked up to the GPU CPR, but we don't have support for that
yet, so until then, just turn on the regulator and keep it on so that we
can focus on basic GPU bringup.

Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
 arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
index f09f3e03f708..108667ce4f31 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
@@ -27,6 +27,23 @@
 	status = "okay";
 };
 
+&pm8005_lsid1 {
+	pm8005-regulators {
+		compatible = "qcom,pm8005-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+
+		pm8005_s1: s1 { /* VDD_GFX supply */
+			regulator-min-microvolt = <524000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-enable-ramp-delay = <500>;
+
+			/* hack until we rig up the gpu consumer */
+			regulator-always-on;
+		};
+	};
+};
+
 &qusb2phy {
 	status = "okay";
 
-- 
2.17.1

[PATCH v2 6/7] dt-bindings: qcom_spmi: Document pms405 support

[Jeffrey Hugo]

From: Jorge Ramirez <jorge.ramirez-ortiz@linaro.org>

The PMS405 supports 5 SMPS and 13 LDO regulators.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
---
 .../regulator/qcom,spmi-regulator.txt         | 24 +++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
index ba94bc2d407a..19cffb239094 100644
--- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
@@ -10,6 +10,7 @@ Qualcomm SPMI Regulators
 			"qcom,pm8941-regulators"
 			"qcom,pm8994-regulators"
 			"qcom,pmi8994-regulators"
+			"qcom,pms405-regulators"
 
 - interrupts:
 	Usage: optional
@@ -111,6 +112,29 @@ Qualcomm SPMI Regulators
 	Definition: Reference to regulator supplying the input pin, as
 		    described in the data sheet.
 
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s3-supply:
+- vdd_s4-supply:
+- vdd_s5-supply:
+- vdd_l1-supply:
+- vdd_l2-supply:
+- vdd_l3-supply:
+- vdd_l4-supply:
+- vdd_l5-supply:
+- vdd_l6-supply:
+- vdd_l7-supply:
+- vdd_l8-supply:
+- vdd_l9-supply:
+- vdd_l10-supply:
+- vdd_l11-supply:
+- vdd_l12-supply:
+- vdd_l13-supply:
+	Usage: optional (pms405 only)
+	Value type: <phandle>
+	Definition: Reference to regulator supplying the input pin, as
+		    described in the data sheet.
+
 - qcom,saw-reg:
 	Usage: optional
 	Value type: <phandle>
-- 
2.17.1

[PATCH v2 7/7] drivers: regulator: qcom: add PMS405 SPMI regulator

[Jeffrey Hugo]

From: Jorge Ramirez <jorge.ramirez-ortiz@linaro.org>

The PMS405 has 5 HFSMPS and 13 LDO regulators,

This commit adds support for one of the 5 HFSMPS regulators (s3) to
the spmi regulator driver.

The PMIC HFSMPS 430 regulators have 8 mV step size and a voltage
control scheme consisting of two  8-bit registers defining a 16-bit
voltage set point in units of millivolts

S3 controls the cpu voltages (s3 is a buck regulator of type HFS430);
it is therefore required so we can enable voltage scaling for safely
running cpufreq.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
---
 drivers/regulator/qcom_spmi-regulator.c | 41 +++++++++++++++++++++++--
 1 file changed, 38 insertions(+), 3 deletions(-)

diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index c7880c1d4bcd..975655e787fe 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -105,6 +105,7 @@ enum spmi_regulator_logical_type {
 	SPMI_REGULATOR_LOGICAL_TYPE_ULT_HO_SMPS,
 	SPMI_REGULATOR_LOGICAL_TYPE_ULT_LDO,
 	SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS426,
+	SPMI_REGULATOR_LOGICAL_TYPE_HFS430,
 };
 
 enum spmi_regulator_type {
@@ -157,6 +158,7 @@ enum spmi_regulator_subtype {
 	SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL2	= 0x0e,
 	SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL3	= 0x0f,
 	SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL4	= 0x10,
+	SPMI_REGULATOR_SUBTYPE_HFS430		= 0x0a,
 };
 
 enum spmi_common_regulator_registers {
@@ -302,6 +304,8 @@ enum spmi_common_control_register_index {
 /* Clock rate in kHz of the FTSMPS426 regulator reference clock. */
 #define SPMI_FTSMPS426_CLOCK_RATE		4800
 
+#define SPMI_HFS430_CLOCK_RATE			1600
+
 /* Minimum voltage stepper delay for each step. */
 #define SPMI_FTSMPS426_STEP_DELAY		2
 
@@ -515,6 +519,10 @@ static struct spmi_voltage_range ult_pldo_ranges[] = {
 	SPMI_VOLTAGE_RANGE(0, 1750000, 1750000, 3337500, 3337500, 12500),
 };
 
+static struct spmi_voltage_range hfs430_ranges[] = {
+	SPMI_VOLTAGE_RANGE(0, 320000, 320000, 2040000, 2040000, 8000),
+};
+
 static DEFINE_SPMI_SET_POINTS(pldo);
 static DEFINE_SPMI_SET_POINTS(nldo1);
 static DEFINE_SPMI_SET_POINTS(nldo2);
@@ -530,6 +538,7 @@ static DEFINE_SPMI_SET_POINTS(ult_lo_smps);
 static DEFINE_SPMI_SET_POINTS(ult_ho_smps);
 static DEFINE_SPMI_SET_POINTS(ult_nldo);
 static DEFINE_SPMI_SET_POINTS(ult_pldo);
+static DEFINE_SPMI_SET_POINTS(hfs430);
 
 static inline int spmi_vreg_read(struct spmi_regulator *vreg, u16 addr, u8 *buf,
 				 int len)
@@ -1397,12 +1406,24 @@ static struct regulator_ops spmi_ftsmps426_ops = {
 	.set_pull_down		= spmi_regulator_common_set_pull_down,
 };
 
+static struct regulator_ops spmi_hfs430_ops = {
+	/* always on regulators */
+	.set_voltage_sel	= spmi_regulator_ftsmps426_set_voltage,
+	.set_voltage_time_sel	= spmi_regulator_set_voltage_time_sel,
+	.get_voltage		= spmi_regulator_ftsmps426_get_voltage,
+	.map_voltage		= spmi_regulator_single_map_voltage,
+	.list_voltage		= spmi_regulator_common_list_voltage,
+	.set_mode		= spmi_regulator_ftsmps426_set_mode,
+	.get_mode		= spmi_regulator_ftsmps426_get_mode,
+};
+
 /* Maximum possible digital major revision value */
 #define INF 0xFF
 
 static const struct spmi_regulator_mapping supported_regulators[] = {
 	/*           type subtype dig_min dig_max ltype ops setpoints hpm_min */
 	SPMI_VREG(BUCK,  GP_CTL,   0, INF, SMPS,   smps,   smps,   100000),
+	SPMI_VREG(BUCK,  HFS430,   0, INF, HFS430, hfs430, hfs430,  10000),
 	SPMI_VREG(LDO,   N300,     0, INF, LDO,    ldo,    nldo1,   10000),
 	SPMI_VREG(LDO,   N600,     0,   0, LDO,    ldo,    nldo2,   10000),
 	SPMI_VREG(LDO,   N1200,    0,   0, LDO,    ldo,    nldo2,   10000),
@@ -1570,7 +1591,8 @@ static int spmi_regulator_init_slew_rate(struct spmi_regulator *vreg)
 	return ret;
 }
 
-static int spmi_regulator_init_slew_rate_ftsmps426(struct spmi_regulator *vreg)
+static int spmi_regulator_init_slew_rate_ftsmps426(struct spmi_regulator *vreg,
+						   int clock_rate)
 {
 	int ret;
 	u8 reg = 0;
@@ -1587,7 +1609,7 @@ static int spmi_regulator_init_slew_rate_ftsmps426(struct spmi_regulator *vreg)
 	delay >>= SPMI_FTSMPS426_STEP_CTRL_DELAY_SHIFT;
 
 	/* slew_rate has units of uV/us */
-	slew_rate = SPMI_FTSMPS426_CLOCK_RATE * range->step_uV;
+	slew_rate = clock_rate * range->step_uV;
 	slew_rate /= 1000 * (SPMI_FTSMPS426_STEP_DELAY << delay);
 	slew_rate *= SPMI_FTSMPS426_STEP_MARGIN_NUM;
 	slew_rate /= SPMI_FTSMPS426_STEP_MARGIN_DEN;
@@ -1739,7 +1761,14 @@ static int spmi_regulator_of_parse(struct device_node *node,
 			return ret;
 		break;
 	case SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS426:
-		ret = spmi_regulator_init_slew_rate_ftsmps426(vreg);
+		ret = spmi_regulator_init_slew_rate_ftsmps426(vreg,
+						SPMI_FTSMPS426_CLOCK_RATE);
+		if (ret)
+			return ret;
+		break;
+	case SPMI_REGULATOR_LOGICAL_TYPE_HFS430:
+		ret = spmi_regulator_init_slew_rate_ftsmps426(vreg,
+							SPMI_HFS430_CLOCK_RATE);
 		if (ret)
 			return ret;
 		break;
@@ -1907,6 +1936,11 @@ static const struct spmi_regulator_data pm8005_regulators[] = {
 	{ }
 };
 
+static const struct spmi_regulator_data pms405_regulators[] = {
+	{ "s3", 0x1a00, }, /* supply name in the dts only */
+	{ }
+};
+
 static const struct of_device_id qcom_spmi_regulator_match[] = {
 	{ .compatible = "qcom,pm8005-regulators", .data = &pm8005_regulators },
 	{ .compatible = "qcom,pm8841-regulators", .data = &pm8841_regulators },
@@ -1914,6 +1948,7 @@ static const struct of_device_id qcom_spmi_regulator_match[] = {
 	{ .compatible = "qcom,pm8941-regulators", .data = &pm8941_regulators },
 	{ .compatible = "qcom,pm8994-regulators", .data = &pm8994_regulators },
 	{ .compatible = "qcom,pmi8994-regulators", .data = &pmi8994_regulators },
+	{ .compatible = "qcom,pms405-regulators", .data = &pms405_regulators },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, qcom_spmi_regulator_match);
-- 
2.17.1

Re: [PATCH v2 7/7] drivers: regulator: qcom: add PMS405 SPMI regulator

[Jeffrey Hugo]

On Thu, Jun 6, 2019 at 12:53 PM Jeffrey Hugo <jeffrey.l.hugo@gmail.com> wrote:
>
> From: Jorge Ramirez <jorge.ramirez-ortiz@linaro.org>
>
> The PMS405 has 5 HFSMPS and 13 LDO regulators,
>
> This commit adds support for one of the 5 HFSMPS regulators (s3) to
> the spmi regulator driver.
>
> The PMIC HFSMPS 430 regulators have 8 mV step size and a voltage
> control scheme consisting of two  8-bit registers defining a 16-bit
> voltage set point in units of millivolts
>
> S3 controls the cpu voltages (s3 is a buck regulator of type HFS430);
> it is therefore required so we can enable voltage scaling for safely
> running cpufreq.
>
> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
> ---
>  drivers/regulator/qcom_spmi-regulator.c | 41 +++++++++++++++++++++++--
>  1 file changed, 38 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
> index c7880c1d4bcd..975655e787fe 100644
> --- a/drivers/regulator/qcom_spmi-regulator.c
> +++ b/drivers/regulator/qcom_spmi-regulator.c
> @@ -105,6 +105,7 @@ enum spmi_regulator_logical_type {
>         SPMI_REGULATOR_LOGICAL_TYPE_ULT_HO_SMPS,
>         SPMI_REGULATOR_LOGICAL_TYPE_ULT_LDO,
>         SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS426,
> +       SPMI_REGULATOR_LOGICAL_TYPE_HFS430,
>  };
>
>  enum spmi_regulator_type {
> @@ -157,6 +158,7 @@ enum spmi_regulator_subtype {
>         SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL2      = 0x0e,
>         SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL3      = 0x0f,
>         SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL4      = 0x10,
> +       SPMI_REGULATOR_SUBTYPE_HFS430           = 0x0a,
>  };
>
>  enum spmi_common_regulator_registers {
> @@ -302,6 +304,8 @@ enum spmi_common_control_register_index {
>  /* Clock rate in kHz of the FTSMPS426 regulator reference clock. */
>  #define SPMI_FTSMPS426_CLOCK_RATE              4800
>
> +#define SPMI_HFS430_CLOCK_RATE                 1600
> +
>  /* Minimum voltage stepper delay for each step. */
>  #define SPMI_FTSMPS426_STEP_DELAY              2
>
> @@ -515,6 +519,10 @@ static struct spmi_voltage_range ult_pldo_ranges[] = {
>         SPMI_VOLTAGE_RANGE(0, 1750000, 1750000, 3337500, 3337500, 12500),
>  };
>
> +static struct spmi_voltage_range hfs430_ranges[] = {
> +       SPMI_VOLTAGE_RANGE(0, 320000, 320000, 2040000, 2040000, 8000),
> +};
> +
>  static DEFINE_SPMI_SET_POINTS(pldo);
>  static DEFINE_SPMI_SET_POINTS(nldo1);
>  static DEFINE_SPMI_SET_POINTS(nldo2);
> @@ -530,6 +538,7 @@ static DEFINE_SPMI_SET_POINTS(ult_lo_smps);
>  static DEFINE_SPMI_SET_POINTS(ult_ho_smps);
>  static DEFINE_SPMI_SET_POINTS(ult_nldo);
>  static DEFINE_SPMI_SET_POINTS(ult_pldo);
> +static DEFINE_SPMI_SET_POINTS(hfs430);
>
>  static inline int spmi_vreg_read(struct spmi_regulator *vreg, u16 addr, u8 *buf,
>                                  int len)
> @@ -1397,12 +1406,24 @@ static struct regulator_ops spmi_ftsmps426_ops = {
>         .set_pull_down          = spmi_regulator_common_set_pull_down,
>  };
>
> +static struct regulator_ops spmi_hfs430_ops = {
> +       /* always on regulators */

From offline discussion, this is apparently now incorrect.  I'll spin
a v3 with this fixed, but I'll wait a bit to see if there are any
other comments, or if this is the only fixup.

> +       .set_voltage_sel        = spmi_regulator_ftsmps426_set_voltage,
> +       .set_voltage_time_sel   = spmi_regulator_set_voltage_time_sel,
> +       .get_voltage            = spmi_regulator_ftsmps426_get_voltage,
> +       .map_voltage            = spmi_regulator_single_map_voltage,
> +       .list_voltage           = spmi_regulator_common_list_voltage,
> +       .set_mode               = spmi_regulator_ftsmps426_set_mode,
> +       .get_mode               = spmi_regulator_ftsmps426_get_mode,
> +};
> +
>  /* Maximum possible digital major revision value */
>  #define INF 0xFF
>
>  static const struct spmi_regulator_mapping supported_regulators[] = {
>         /*           type subtype dig_min dig_max ltype ops setpoints hpm_min */
>         SPMI_VREG(BUCK,  GP_CTL,   0, INF, SMPS,   smps,   smps,   100000),
> +       SPMI_VREG(BUCK,  HFS430,   0, INF, HFS430, hfs430, hfs430,  10000),
>         SPMI_VREG(LDO,   N300,     0, INF, LDO,    ldo,    nldo1,   10000),
>         SPMI_VREG(LDO,   N600,     0,   0, LDO,    ldo,    nldo2,   10000),
>         SPMI_VREG(LDO,   N1200,    0,   0, LDO,    ldo,    nldo2,   10000),
> @@ -1570,7 +1591,8 @@ static int spmi_regulator_init_slew_rate(struct spmi_regulator *vreg)
>         return ret;
>  }
>
> -static int spmi_regulator_init_slew_rate_ftsmps426(struct spmi_regulator *vreg)
> +static int spmi_regulator_init_slew_rate_ftsmps426(struct spmi_regulator *vreg,
> +                                                  int clock_rate)
>  {
>         int ret;
>         u8 reg = 0;
> @@ -1587,7 +1609,7 @@ static int spmi_regulator_init_slew_rate_ftsmps426(struct spmi_regulator *vreg)
>         delay >>= SPMI_FTSMPS426_STEP_CTRL_DELAY_SHIFT;
>
>         /* slew_rate has units of uV/us */
> -       slew_rate = SPMI_FTSMPS426_CLOCK_RATE * range->step_uV;
> +       slew_rate = clock_rate * range->step_uV;
>         slew_rate /= 1000 * (SPMI_FTSMPS426_STEP_DELAY << delay);
>         slew_rate *= SPMI_FTSMPS426_STEP_MARGIN_NUM;
>         slew_rate /= SPMI_FTSMPS426_STEP_MARGIN_DEN;
> @@ -1739,7 +1761,14 @@ static int spmi_regulator_of_parse(struct device_node *node,
>                         return ret;
>                 break;
>         case SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS426:
> -               ret = spmi_regulator_init_slew_rate_ftsmps426(vreg);
> +               ret = spmi_regulator_init_slew_rate_ftsmps426(vreg,
> +                                               SPMI_FTSMPS426_CLOCK_RATE);
> +               if (ret)
> +                       return ret;
> +               break;
> +       case SPMI_REGULATOR_LOGICAL_TYPE_HFS430:
> +               ret = spmi_regulator_init_slew_rate_ftsmps426(vreg,
> +                                                       SPMI_HFS430_CLOCK_RATE);
>                 if (ret)
>                         return ret;
>                 break;
> @@ -1907,6 +1936,11 @@ static const struct spmi_regulator_data pm8005_regulators[] = {
>         { }
>  };
>
> +static const struct spmi_regulator_data pms405_regulators[] = {
> +       { "s3", 0x1a00, }, /* supply name in the dts only */
> +       { }
> +};
> +
>  static const struct of_device_id qcom_spmi_regulator_match[] = {
>         { .compatible = "qcom,pm8005-regulators", .data = &pm8005_regulators },
>         { .compatible = "qcom,pm8841-regulators", .data = &pm8841_regulators },
> @@ -1914,6 +1948,7 @@ static const struct of_device_id qcom_spmi_regulator_match[] = {
>         { .compatible = "qcom,pm8941-regulators", .data = &pm8941_regulators },
>         { .compatible = "qcom,pm8994-regulators", .data = &pm8994_regulators },
>         { .compatible = "qcom,pmi8994-regulators", .data = &pmi8994_regulators },
> +       { .compatible = "qcom,pms405-regulators", .data = &pms405_regulators },
>         { }
>  };
>  MODULE_DEVICE_TABLE(of, qcom_spmi_regulator_match);
> --
> 2.17.1
>

Re: [PATCH v2 1/7] drivers: regulator: qcom_spmi: enable linear range info

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 388 bytes --]

On Thu, Jun 06, 2019 at 11:49:23AM -0700, Jeffrey Hugo wrote:
> From: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> 
> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>

Please use subject lines matching the style for the subsystem.  This
makes it easier for people to identify relevant patches.

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

Re: [PATCH v2 1/7] drivers: regulator: qcom_spmi: enable linear range info

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 926 bytes --]

On Thu, Jun 06, 2019 at 11:49:23AM -0700, Jeffrey Hugo wrote:

> +		if (vreg->logical_type == SPMI_REGULATOR_LOGICAL_TYPE_HFS430) {
> +			/* since there is only one range */
> +			range = spmi_regulator_find_range(vreg);
> +			vreg->desc.uV_step = range->step_uV;
> +		}

This doesn't build for me:

drivers/regulator/qcom_spmi-regulator.c: In function ‘qcom_spmi_regulator_probe’:
drivers/regulator/qcom_spmi-regulator.c:1837:29: error: ‘SPMI_REGULATOR_LOGICAL_TYPE_HFS430’ undeclared (first use in this function); did you mean ‘SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS’?
   if (vreg->logical_type == SPMI_REGULATOR_LOGICAL_TYPE_HFS430) {
                             ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
                             SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS
drivers/regulator/qcom_spmi-regulator.c:1837:29: note: each undeclared identifier is reported only once for each function it appears in

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]