linux-arm-msm.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Stephan Gerhold <stephan@gerhold.net>
To: Andy Gross <agross@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>,
	linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org,
	Stephan Gerhold <stephan@gerhold.net>,
	Michael Srba <Michael.Srba@seznam.cz>
Subject: [RFC PATCH v2 3/4] arm64: dts: qcom: Add device tree for Samsung Galaxy A3U/A5U
Date: Mon, 22 Jul 2019 11:22:10 +0200	[thread overview]
Message-ID: <20190722092211.100586-4-stephan@gerhold.net> (raw)
In-Reply-To: <20190722092211.100586-1-stephan@gerhold.net>

Samsung Galaxy A3 (SM-A300FU) and Samsung Galaxy A5 (SM-A500FU)
are smartphones using the MSM8916 SoC released in 2015.

Add a device tree for A3U and A5U with initial support for:
  - SDHCI (internal and external storage)
  - USB Device Mode
  - UART (on USB connector via the SM5502 MUIC)
  - Regulators

The two devices (and all other variants of A3/A5 released in 2015)
are very similar, with some differences in display, touchscreen
and sensors. The common parts are shared in
msm8916-samsung-a2015-common.dtsi to reduce duplication.

The device tree is loosely based on apq8016-sbc.dtsi and the
downstream kernel provided by Samsung, mixed with a lot of own
research.

Co-developed-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
---
Changes in v2:
  - Remove msm8916-samsung-a2015-common-pins.dtsi, move to main .dtsi
  - Update s4/l17 regulator-max-microvolt, remove regulator-always-on
  - Use muic extcon device for both VBUS/USB-ID in usb@78d9000
  - Move i2c-muic out of soc { ... } node

 arch/arm64/boot/dts/qcom/Makefile             |   2 +
 .../qcom/msm8916-samsung-a2015-common.dtsi    | 236 ++++++++++++++++++
 .../boot/dts/qcom/msm8916-samsung-a3u-eur.dts |  10 +
 .../boot/dts/qcom/msm8916-samsung-a5u-eur.dts |  10 +
 4 files changed, 258 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi
 create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-a3u-eur.dts
 create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-a5u-eur.dts

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 0a7e5dfce6f7..5d725770d9c4 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -3,6 +3,8 @@ dtb-$(CONFIG_ARCH_QCOM)	+= apq8016-sbc.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= apq8096-db820c.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq8074-hk01.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-a3u-eur.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-a5u-eur.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8992-bullhead-rev-101.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8994-angler-rev-101.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8996-mtp.dtb
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi b/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi
new file mode 100644
index 000000000000..e675ff48fdd2
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi
@@ -0,0 +1,236 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include "msm8916.dtsi"
+#include "pm8916.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	aliases {
+		serial0 = &blsp1_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	soc {
+		sdhci@7824000 {
+			status = "okay";
+
+			vmmc-supply = <&pm8916_l8>;
+			vqmmc-supply = <&pm8916_l5>;
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
+			pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
+		};
+
+		sdhci@7864000 {
+			status = "okay";
+
+			vmmc-supply = <&pm8916_l11>;
+			vqmmc-supply = <&pm8916_l12>;
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
+			pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+
+			cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>;
+		};
+
+		serial@78b0000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_uart2_default>;
+			pinctrl-1 = <&blsp1_uart2_sleep>;
+		};
+
+		usb@78d9000 {
+			status = "okay";
+			extcon = <&muic>, <&muic>;
+
+			hnp-disable;
+			srp-disable;
+			adp-disable;
+
+			ulpi {
+				phy {
+					extcon = <&muic>;
+					v1p8-supply = <&pm8916_l7>;
+					v3p3-supply = <&pm8916_l13>;
+				};
+			};
+		};
+
+		/*
+		 * Attempting to enable these devices causes a "synchronous
+		 * external abort". Suspected cause is that the debug power
+		 * domain is not enabled by default on this device.
+		 * Disable these devices for now to avoid the crash.
+		 *
+		 * See: https://lore.kernel.org/linux-arm-msm/20190618202623.GA53651@gerhold.net/
+		 */
+		tpiu@820000 { status = "disabled"; };
+		funnel@821000 { status = "disabled"; };
+		replicator@824000 { status = "disabled"; };
+		etf@825000 { status = "disabled"; };
+		etr@826000 { status = "disabled"; };
+		funnel@841000 { status = "disabled"; };
+		debug@850000 { status = "disabled"; };
+		debug@852000 { status = "disabled"; };
+		debug@854000 { status = "disabled"; };
+		debug@856000 { status = "disabled"; };
+		etm@85c000 { status = "disabled"; };
+		etm@85d000 { status = "disabled"; };
+		etm@85e000 { status = "disabled"; };
+		etm@85f000 { status = "disabled"; };
+	};
+
+	i2c-muic {
+		compatible = "i2c-gpio";
+		sda-gpios = <&msmgpio 105 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&msmgpio 106 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		muic: sm5502@25 {
+			compatible = "siliconmitus,sm5502-muic";
+
+			reg = <0x25>;
+			interrupt-parent = <&msmgpio>;
+			interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&muic_int_default>;
+		};
+	};
+};
+
+&msmgpio {
+	muic_int_default: muic_int_default {
+		pinmux {
+			function = "gpio";
+			pins = "gpio12";
+		};
+		pinconf {
+			pins = "gpio12";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+};
+
+&smd_rpm_regulators {
+	vdd_l1_l2_l3-supply = <&pm8916_s3>;
+	vdd_l4_l5_l6-supply = <&pm8916_s4>;
+	vdd_l7-supply = <&pm8916_s4>;
+
+	s1 {
+		regulator-min-microvolt = <500000>;
+		regulator-max-microvolt = <1300000>;
+	};
+
+	s3 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1300000>;
+	};
+
+	s4 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2100000>;
+	};
+
+	l1 {
+		regulator-min-microvolt = <1225000>;
+		regulator-max-microvolt = <1225000>;
+	};
+
+	l2 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+	};
+
+	l3 {
+		regulator-min-microvolt = <500000>;
+		regulator-max-microvolt = <1287500>;
+	};
+
+	l4 {
+		regulator-min-microvolt = <2050000>;
+		regulator-max-microvolt = <2050000>;
+	};
+
+	l5 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l6 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l7 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l8 {
+		regulator-min-microvolt = <2850000>;
+		regulator-max-microvolt = <2900000>;
+	};
+
+	l9 {
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l10 {
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2800000>;
+	};
+
+	l11 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2950000>;
+		regulator-allow-set-load;
+		regulator-system-load = <200000>;
+	};
+
+	l12 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2950000>;
+	};
+
+	l13 {
+		regulator-min-microvolt = <3075000>;
+		regulator-max-microvolt = <3075000>;
+	};
+
+	l14 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l15 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l16 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l17 {
+		regulator-min-microvolt = <2850000>;
+		regulator-max-microvolt = <2850000>;
+	};
+
+	l18 {
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2700000>;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-a3u-eur.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-a3u-eur.dts
new file mode 100644
index 000000000000..d10f7ac5089f
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-a3u-eur.dts
@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8916-samsung-a2015-common.dtsi"
+
+/ {
+	model = "Samsung Galaxy A3U (EUR)";
+	compatible = "samsung,a3u-eur", "qcom,msm8916";
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-a5u-eur.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-a5u-eur.dts
new file mode 100644
index 000000000000..1aa59da98495
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-a5u-eur.dts
@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8916-samsung-a2015-common.dtsi"
+
+/ {
+	model = "Samsung Galaxy A5U (EUR)";
+	compatible = "samsung,a5u-eur", "qcom,msm8916";
+};
-- 
2.22.0


  parent reply	other threads:[~2019-07-22  9:24 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-07-22  9:22 [RFC PATCH v2 0/4] Add initial device tree for MSM8916 A3U/A5U/L8150 Stephan Gerhold
2019-07-22  9:22 ` [RFC PATCH v2 1/4] dt-bindings: vendor-prefixes: Add Longcheer Technology Co., Ltd Stephan Gerhold
2019-07-22 15:12   ` Rob Herring
2019-07-22  9:22 ` [RFC PATCH v2 2/4] dt-bindings: qcom: Document bindings for new MSM8916 devices Stephan Gerhold
2019-07-22 15:12   ` Rob Herring
2019-07-22  9:22 ` Stephan Gerhold [this message]
2019-07-22  9:22 ` [RFC PATCH v2 4/4] arm64: dts: qcom: Add device tree for Longcheer L8150 Stephan Gerhold

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190722092211.100586-4-stephan@gerhold.net \
    --to=stephan@gerhold.net \
    --cc=Michael.Srba@seznam.cz \
    --cc=agross@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).