* [PATCH v3 1/8] arm64: dts: qcom: sm8150: Add base dts file
2019-08-20 17:23 [PATCH v3 0/8] arm64: dts: qcom: sm8150: Add SM8150 DTS Vinod Koul
@ 2019-08-20 17:23 ` Vinod Koul
2019-08-20 17:23 ` [PATCH v3 2/8] arm64: dts: qcom: pm8150: " Vinod Koul
` (8 subsequent siblings)
9 siblings, 0 replies; 14+ messages in thread
From: Vinod Koul @ 2019-08-20 17:23 UTC (permalink / raw)
To: Andy Gross
Cc: linux-arm-msm, Bjorn Andersson, Vinod Koul, Rob Herring,
Mark Rutland, Stephen Boyd, Sibi Sankar, devicetree,
linux-kernel
This add base DTS file with cpu, psci, firmware, clock node tlmm and
spmi and enables boot to console
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/sm8150.dtsi | 307 +++++++++++++++++++++++++++
1 file changed, 307 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sm8150.dtsi
diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
new file mode 100644
index 000000000000..ba5a9f6332c1
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
@@ -0,0 +1,307 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2019, Linaro Limited
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+
+/ {
+ interrupt-parent = <&intc>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ chosen { };
+
+ clocks {
+ xo_board: xo-board {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <38400000>;
+ clock-output-names = "xo_board";
+ };
+
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32764>;
+ clock-output-names = "sleep_clk";
+ };
+ };
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ CPU0: cpu@0 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ next-level-cache = <&L2_0>;
+ L2_0: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ L3_0: l3-cache {
+ compatible = "cache";
+ };
+ };
+ };
+
+ CPU1: cpu@100 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x100>;
+ enable-method = "psci";
+ next-level-cache = <&L2_100>;
+ L2_100: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+
+ };
+
+ CPU2: cpu@200 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x200>;
+ enable-method = "psci";
+ next-level-cache = <&L2_200>;
+ L2_200: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU3: cpu@300 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x300>;
+ enable-method = "psci";
+ next-level-cache = <&L2_300>;
+ L2_300: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU4: cpu@400 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x400>;
+ enable-method = "psci";
+ next-level-cache = <&L2_400>;
+ L2_400: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU5: cpu@500 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x500>;
+ enable-method = "psci";
+ next-level-cache = <&L2_500>;
+ L2_500: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU6: cpu@600 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x600>;
+ enable-method = "psci";
+ next-level-cache = <&L2_600>;
+ L2_600: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU7: cpu@700 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x700>;
+ enable-method = "psci";
+ next-level-cache = <&L2_700>;
+ L2_700: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+ };
+
+ firmware {
+ scm: scm {
+ compatible = "qcom,scm-sm8150", "qcom,scm";
+ #reset-cells = <1>;
+ };
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ /* We expect the bootloader to fill in the size */
+ reg = <0x0 0x80000000 0x0 0x0>;
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ soc: soc@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x0 0x0 0xffffffff>;
+ compatible = "simple-bus";
+
+ gcc: clock-controller@100000 {
+ compatible = "qcom,gcc-sm8150";
+ reg = <0x00100000 0x1f0000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ clock-names = "bi_tcxo",
+ "sleep_clk";
+ clocks = <&rpmhcc RPMH_CXO_CLK>,
+ <&sleep_clk>;
+ };
+
+ qupv3_id_1: geniqup@ac0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0x00ac0000 0x6000>;
+ clock-names = "m-ahb", "s-ahb";
+ clocks = <&gcc 123>,
+ <&gcc 124>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ status = "disabled";
+
+ uart2: serial@a90000 {
+ compatible = "qcom,geni-debug-uart";
+ reg = <0x00a90000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc 105>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+ };
+
+ tlmm: pinctrl@3100000 {
+ compatible = "qcom,sm8150-pinctrl";
+ reg = <0x03100000 0x300000>,
+ <0x03500000 0x300000>,
+ <0x03900000 0x300000>,
+ <0x03d00000 0x300000>;
+ reg-names = "west", "east", "north", "south";
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-ranges = <&tlmm 0 0 175>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ intc: interrupt-controller@17a00000 {
+ compatible = "arm,gic-v3";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ reg = <0x17a00000 0x10000>, /* GICD */
+ <0x17a60000 0x100000>; /* GICR * 8 */
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ timer@17c20000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ compatible = "arm,armv7-timer-mem";
+ reg = <0x17c20000 0x1000>;
+ clock-frequency = <19200000>;
+
+ frame@17c21000{
+ frame-number = <0>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x17c21000 0x1000>,
+ <0x17c22000 0x1000>;
+ };
+
+ frame@17c23000 {
+ frame-number = <1>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x17c23000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@17c25000 {
+ frame-number = <2>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x17c25000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@17c27000 {
+ frame-number = <3>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x17c26000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@17c29000 {
+ frame-number = <4>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x17c29000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@17c2b000 {
+ frame-number = <5>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x17c2b000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@17c2d000 {
+ frame-number = <6>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x17c2d000 0x1000>;
+ status = "disabled";
+ };
+ };
+
+ spmi_bus: spmi@c440000 {
+ compatible = "qcom,spmi-pmic-arb";
+ reg = <0x0c440000 0x0001100>,
+ <0x0c600000 0x2000000>,
+ <0x0e600000 0x0100000>,
+ <0x0e700000 0x00a0000>,
+ <0x0c40a000 0x0026000>;
+ reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+ interrupt-names = "periph_irq";
+ interrupts = <GIC_SPI 481 IRQ_TYPE_LEVEL_HIGH>;
+ qcom,ee = <0>;
+ qcom,channel = <0>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+ interrupt-controller;
+ #interrupt-cells = <4>;
+ cell-index = <0>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 1 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 2 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 3 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
--
2.20.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v3 2/8] arm64: dts: qcom: pm8150: Add base dts file
2019-08-20 17:23 [PATCH v3 0/8] arm64: dts: qcom: sm8150: Add SM8150 DTS Vinod Koul
2019-08-20 17:23 ` [PATCH v3 1/8] arm64: dts: qcom: sm8150: Add base dts file Vinod Koul
@ 2019-08-20 17:23 ` Vinod Koul
2019-08-20 17:23 ` [PATCH v3 3/8] arm64: dts: qcom: pm8150b: " Vinod Koul
` (7 subsequent siblings)
9 siblings, 0 replies; 14+ messages in thread
From: Vinod Koul @ 2019-08-20 17:23 UTC (permalink / raw)
To: Andy Gross
Cc: linux-arm-msm, Bjorn Andersson, Vinod Koul, Rob Herring,
Mark Rutland, Stephen Boyd, Sibi Sankar, devicetree,
linux-kernel
Add base DTS file for pm8150 along with GPIOs, power-on, rtc and vadc
nodes
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/pm8150.dtsi | 97 ++++++++++++++++++++++++++++
1 file changed, 97 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/pm8150.dtsi
diff --git a/arch/arm64/boot/dts/qcom/pm8150.dtsi b/arch/arm64/boot/dts/qcom/pm8150.dtsi
new file mode 100644
index 000000000000..b6e304748a57
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm8150.dtsi
@@ -0,0 +1,97 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2019, Linaro Limited
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+
+&spmi_bus {
+ pm8150_0: pmic@0 {
+ compatible = "qcom,pm8150", "qcom,spmi-pmic";
+ reg = <0x0 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pon: power-on@800 {
+ compatible = "qcom,pm8916-pon";
+ reg = <0x0800>;
+ pwrkey {
+ compatible = "qcom,pm8941-pwrkey";
+ interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ linux,code = <KEY_POWER>;
+
+ status = "disabled";
+ };
+ };
+
+ pm8150_adc: adc@3100 {
+ compatible = "qcom,spmi-adc5";
+ reg = <0x3100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+ interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+ status = "disabled";
+
+ ref-gnd@0 {
+ reg = <ADC5_REF_GND>;
+ qcom,pre-scaling = <1 1>;
+ label = "ref_gnd";
+ };
+
+ vref-1p25@1 {
+ reg = <ADC5_1P25VREF>;
+ qcom,pre-scaling = <1 1>;
+ label = "vref_1p25";
+ };
+
+ die-temp@6 {
+ reg = <ADC5_DIE_TEMP>;
+ qcom,pre-scaling = <1 1>;
+ label = "die_temp";
+ };
+ };
+
+ rtc@6000 {
+ compatible = "qcom,pm8941-rtc";
+ reg = <0x6000>;
+ reg-names = "rtc", "alarm";
+ interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
+
+ status = "disabled";
+ };
+
+ pm8150_gpios: gpio@c000 {
+ compatible = "qcom,pm8150-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <0x0 0xc0 0x0 IRQ_TYPE_NONE>,
+ <0x0 0xc1 0x0 IRQ_TYPE_NONE>,
+ <0x0 0xc2 0x0 IRQ_TYPE_NONE>,
+ <0x0 0xc3 0x0 IRQ_TYPE_NONE>,
+ <0x0 0xc4 0x0 IRQ_TYPE_NONE>,
+ <0x0 0xc5 0x0 IRQ_TYPE_NONE>,
+ <0x0 0xc6 0x0 IRQ_TYPE_NONE>,
+ <0x0 0xc7 0x0 IRQ_TYPE_NONE>,
+ <0x0 0xc8 0x0 IRQ_TYPE_NONE>,
+ <0x0 0xc9 0x0 IRQ_TYPE_NONE>,
+ <0x0 0xca 0x0 IRQ_TYPE_NONE>,
+ <0x0 0xcb 0x0 IRQ_TYPE_NONE>;
+ };
+ };
+
+ pmic@1 {
+ compatible = "qcom,pm8150", "qcom,spmi-pmic";
+ reg = <0x1 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
--
2.20.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v3 3/8] arm64: dts: qcom: pm8150b: Add base dts file
2019-08-20 17:23 [PATCH v3 0/8] arm64: dts: qcom: sm8150: Add SM8150 DTS Vinod Koul
2019-08-20 17:23 ` [PATCH v3 1/8] arm64: dts: qcom: sm8150: Add base dts file Vinod Koul
2019-08-20 17:23 ` [PATCH v3 2/8] arm64: dts: qcom: pm8150: " Vinod Koul
@ 2019-08-20 17:23 ` Vinod Koul
2019-08-20 17:23 ` [PATCH v3 4/8] arm64: dts: qcom: pm8150l: " Vinod Koul
` (6 subsequent siblings)
9 siblings, 0 replies; 14+ messages in thread
From: Vinod Koul @ 2019-08-20 17:23 UTC (permalink / raw)
To: Andy Gross
Cc: linux-arm-msm, Bjorn Andersson, Vinod Koul, Rob Herring,
Mark Rutland, Stephen Boyd, Sibi Sankar, devicetree,
linux-kernel
PMIC pm8150b is a slave pmic and this adds base DTS file for pm8150b
with power-on, adc, and gpio nodes
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/pm8150b.dtsi | 86 +++++++++++++++++++++++++++
1 file changed, 86 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/pm8150b.dtsi
diff --git a/arch/arm64/boot/dts/qcom/pm8150b.dtsi b/arch/arm64/boot/dts/qcom/pm8150b.dtsi
new file mode 100644
index 000000000000..322379d5c31f
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm8150b.dtsi
@@ -0,0 +1,86 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2019, Linaro Limited
+ */
+
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+ pmic@2 {
+ compatible = "qcom,pm8150b", "qcom,spmi-pmic";
+ reg = <0x2 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ power-on@800 {
+ compatible = "qcom,pm8916-pon";
+ reg = <0x0800>;
+
+ status = "disabled";
+ };
+
+ adc@3100 {
+ compatible = "qcom,spmi-adc5";
+ reg = <0x3100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+ interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+ status = "disabled";
+
+ ref-gnd@0 {
+ reg = <ADC5_REF_GND>;
+ qcom,pre-scaling = <1 1>;
+ label = "ref_gnd";
+ };
+
+ vref-1p25@1 {
+ reg = <ADC5_1P25VREF>;
+ qcom,pre-scaling = <1 1>;
+ label = "vref_1p25";
+ };
+
+ die-temp@6 {
+ reg = <ADC5_DIE_TEMP>;
+ qcom,pre-scaling = <1 1>;
+ label = "die_temp";
+ };
+
+ chg-temp@9 {
+ reg = <ADC5_CHG_TEMP>;
+ qcom,pre-scaling = <1 1>;
+ label = "chg_temp";
+ };
+ };
+
+ pm8150b_gpios: gpio@c000 {
+ compatible = "qcom,pm8150b-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <0x2 0xc0 0x0 IRQ_TYPE_NONE>,
+ <0x2 0xc1 0x0 IRQ_TYPE_NONE>,
+ <0x2 0xc2 0x0 IRQ_TYPE_NONE>,
+ <0x2 0xc3 0x0 IRQ_TYPE_NONE>,
+ <0x2 0xc4 0x0 IRQ_TYPE_NONE>,
+ <0x2 0xc5 0x0 IRQ_TYPE_NONE>,
+ <0x2 0xc6 0x0 IRQ_TYPE_NONE>,
+ <0x2 0xc7 0x0 IRQ_TYPE_NONE>,
+ <0x2 0xc8 0x0 IRQ_TYPE_NONE>,
+ <0x2 0xc9 0x0 IRQ_TYPE_NONE>,
+ <0x2 0xca 0x0 IRQ_TYPE_NONE>,
+ <0x2 0xcb 0x0 IRQ_TYPE_NONE>;
+ };
+ };
+
+ pmic@3 {
+ compatible = "qcom,pm8150b", "qcom,spmi-pmic";
+ reg = <0x3 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
--
2.20.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v3 4/8] arm64: dts: qcom: pm8150l: Add base dts file
2019-08-20 17:23 [PATCH v3 0/8] arm64: dts: qcom: sm8150: Add SM8150 DTS Vinod Koul
` (2 preceding siblings ...)
2019-08-20 17:23 ` [PATCH v3 3/8] arm64: dts: qcom: pm8150b: " Vinod Koul
@ 2019-08-20 17:23 ` Vinod Koul
2019-08-20 17:23 ` [PATCH v3 5/8] arm64: dts: qcom: sm8150-mtp: " Vinod Koul
` (5 subsequent siblings)
9 siblings, 0 replies; 14+ messages in thread
From: Vinod Koul @ 2019-08-20 17:23 UTC (permalink / raw)
To: Andy Gross
Cc: linux-arm-msm, Bjorn Andersson, Vinod Koul, Rob Herring,
Mark Rutland, Stephen Boyd, Sibi Sankar, devicetree,
linux-kernel
PMIC pm8150l is a slave pmic and this adds base DTS file for pm8150l
with power-on, adc and gpio nodes
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/pm8150l.dtsi | 80 +++++++++++++++++++++++++++
1 file changed, 80 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/pm8150l.dtsi
diff --git a/arch/arm64/boot/dts/qcom/pm8150l.dtsi b/arch/arm64/boot/dts/qcom/pm8150l.dtsi
new file mode 100644
index 000000000000..eb0e9a090e42
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm8150l.dtsi
@@ -0,0 +1,80 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2019, Linaro Limited
+ */
+
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+ pmic@4 {
+ compatible = "qcom,pm8150l", "qcom,spmi-pmic";
+ reg = <0x4 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ power-on@800 {
+ compatible = "qcom,pm8916-pon";
+ reg = <0x0800>;
+
+ status = "disabled";
+ };
+
+ adc@3100 {
+ compatible = "qcom,spmi-adc5";
+ reg = <0x3100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+ interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+ status = "disabled";
+
+ ref-gnd@0 {
+ reg = <ADC5_REF_GND>;
+ qcom,pre-scaling = <1 1>;
+ label = "ref_gnd";
+ };
+
+ vref-1p25@1 {
+ reg = <ADC5_1P25VREF>;
+ qcom,pre-scaling = <1 1>;
+ label = "vref_1p25";
+ };
+
+ die-temp@6 {
+ reg = <ADC5_DIE_TEMP>;
+ qcom,pre-scaling = <1 1>;
+ label = "die_temp";
+ };
+ };
+
+ pm8150l_gpios: gpio@c000 {
+ compatible = "qcom,pm8150l-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <0x4 0xc0 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xc1 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xc2 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xc3 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xc4 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xc5 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xc6 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xc7 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xc8 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xc9 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xca 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xcb 0x0 IRQ_TYPE_NONE>;
+ };
+ };
+
+ pmic@5 {
+ compatible = "qcom,pm8150l", "qcom,spmi-pmic";
+ reg = <0x5 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
--
2.20.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v3 5/8] arm64: dts: qcom: sm8150-mtp: Add base dts file
2019-08-20 17:23 [PATCH v3 0/8] arm64: dts: qcom: sm8150: Add SM8150 DTS Vinod Koul
` (3 preceding siblings ...)
2019-08-20 17:23 ` [PATCH v3 4/8] arm64: dts: qcom: pm8150l: " Vinod Koul
@ 2019-08-20 17:23 ` Vinod Koul
2019-08-20 17:23 ` [PATCH v3 5/8] arm64: dts: qcom: sm8150-mtp: add " Vinod Koul
` (4 subsequent siblings)
9 siblings, 0 replies; 14+ messages in thread
From: Vinod Koul @ 2019-08-20 17:23 UTC (permalink / raw)
To: Andy Gross
Cc: linux-arm-msm, Bjorn Andersson, Vinod Koul, Rob Herring,
Mark Rutland, Stephen Boyd, Sibi Sankar, devicetree,
linux-kernel
This add base DTS file for sm8150-mtp and enables boot to console, adds
tlmm reserved range, resin node, volume down key and also includes pmic
file.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/sm8150-mtp.dts | 51 +++++++++++++++++++++++++
2 files changed, 52 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sm8150-mtp.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 0a7e5dfce6f7..1964dacaf19b 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -12,5 +12,6 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sm8150-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm8150-mtp.dts b/arch/arm64/boot/dts/qcom/sm8150-mtp.dts
new file mode 100644
index 000000000000..6f5777f530ae
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8150-mtp.dts
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2019, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include "sm8150.dtsi"
+#include "pm8150.dtsi"
+#include "pm8150b.dtsi"
+#include "pm8150l.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. SM8150 MTP";
+ compatible = "qcom,sm8150-mtp";
+
+ aliases {
+ serial0 = &uart2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&pon {
+ pwrkey {
+ status = "okay";
+ };
+
+ resin {
+ compatible = "qcom,pm8941-resin";
+ interrupts = <0x0 0x8 0x1 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+};
+
+&tlmm {
+ gpio-reserved-ranges = <0 4>, <126 4>;
+};
+
+&uart2 {
+ status = "okay";
+};
--
2.20.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v3 5/8] arm64: dts: qcom: sm8150-mtp: add base dts file
2019-08-20 17:23 [PATCH v3 0/8] arm64: dts: qcom: sm8150: Add SM8150 DTS Vinod Koul
` (4 preceding siblings ...)
2019-08-20 17:23 ` [PATCH v3 5/8] arm64: dts: qcom: sm8150-mtp: " Vinod Koul
@ 2019-08-20 17:23 ` Vinod Koul
2019-08-21 8:28 ` Amit Kucheria
2019-08-20 17:23 ` [PATCH v3 6/8] arm64: dts: qcom: sm8150-mtp: Add regulators Vinod Koul
` (3 subsequent siblings)
9 siblings, 1 reply; 14+ messages in thread
From: Vinod Koul @ 2019-08-20 17:23 UTC (permalink / raw)
To: Andy Gross
Cc: linux-arm-msm, Bjorn Andersson, Vinod Koul, Rob Herring,
Mark Rutland, Stephen Boyd, Sibi Sankar, devicetree,
linux-kernel
This add base DTS file for sm8150-mtp and enables boot to console, adds
tlmm reserved range, resin node, volume down key and also includes pmic
file.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/sm8150-mtp.dts | 51 +++++++++++++++++++++++++
2 files changed, 52 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sm8150-mtp.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 0a7e5dfce6f7..1964dacaf19b 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -12,5 +12,6 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sm8150-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm8150-mtp.dts b/arch/arm64/boot/dts/qcom/sm8150-mtp.dts
new file mode 100644
index 000000000000..6f5777f530ae
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8150-mtp.dts
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2019, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include "sm8150.dtsi"
+#include "pm8150.dtsi"
+#include "pm8150b.dtsi"
+#include "pm8150l.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. SM8150 MTP";
+ compatible = "qcom,sm8150-mtp";
+
+ aliases {
+ serial0 = &uart2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&pon {
+ pwrkey {
+ status = "okay";
+ };
+
+ resin {
+ compatible = "qcom,pm8941-resin";
+ interrupts = <0x0 0x8 0x1 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+};
+
+&tlmm {
+ gpio-reserved-ranges = <0 4>, <126 4>;
+};
+
+&uart2 {
+ status = "okay";
+};
--
2.20.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* Re: [PATCH v3 5/8] arm64: dts: qcom: sm8150-mtp: add base dts file
2019-08-20 17:23 ` [PATCH v3 5/8] arm64: dts: qcom: sm8150-mtp: add " Vinod Koul
@ 2019-08-21 8:28 ` Amit Kucheria
0 siblings, 0 replies; 14+ messages in thread
From: Amit Kucheria @ 2019-08-21 8:28 UTC (permalink / raw)
To: Vinod Koul
Cc: Andy Gross, linux-arm-msm, Bjorn Andersson, Rob Herring,
Mark Rutland, Stephen Boyd, Sibi Sankar,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, LKML
On Tue, Aug 20, 2019 at 10:55 PM Vinod Koul <vkoul@kernel.org> wrote:
>
> This add base DTS file for sm8150-mtp and enables boot to console, adds
> tlmm reserved range, resin node, volume down key and also includes pmic
> file.
For some reason, your mailer sent out 2 patches 5/8. I was wondering
why the patch 5 failed to apply, but it seems the two are identical.
Lore seems to show the same.
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> arch/arm64/boot/dts/qcom/sm8150-mtp.dts | 51 +++++++++++++++++++++++++
> 2 files changed, 52 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/sm8150-mtp.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 0a7e5dfce6f7..1964dacaf19b 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -12,5 +12,6 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += sm8150-mtp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sm8150-mtp.dts b/arch/arm64/boot/dts/qcom/sm8150-mtp.dts
> new file mode 100644
> index 000000000000..6f5777f530ae
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sm8150-mtp.dts
> @@ -0,0 +1,51 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2019, Linaro Limited
> + */
> +
> +/dts-v1/;
> +
> +#include "sm8150.dtsi"
> +#include "pm8150.dtsi"
> +#include "pm8150b.dtsi"
> +#include "pm8150l.dtsi"
> +
> +/ {
> + model = "Qualcomm Technologies, Inc. SM8150 MTP";
> + compatible = "qcom,sm8150-mtp";
> +
> + aliases {
> + serial0 = &uart2;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +};
> +
> +&qupv3_id_1 {
> + status = "okay";
> +};
> +
> +&pon {
> + pwrkey {
> + status = "okay";
> + };
> +
> + resin {
> + compatible = "qcom,pm8941-resin";
> + interrupts = <0x0 0x8 0x1 IRQ_TYPE_EDGE_BOTH>;
> + debounce = <15625>;
> + bias-pull-up;
> + linux,code = <KEY_VOLUMEDOWN>;
> + };
> +};
> +
> +&tlmm {
> + gpio-reserved-ranges = <0 4>, <126 4>;
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> --
> 2.20.1
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v3 6/8] arm64: dts: qcom: sm8150-mtp: Add regulators
2019-08-20 17:23 [PATCH v3 0/8] arm64: dts: qcom: sm8150: Add SM8150 DTS Vinod Koul
` (5 preceding siblings ...)
2019-08-20 17:23 ` [PATCH v3 5/8] arm64: dts: qcom: sm8150-mtp: add " Vinod Koul
@ 2019-08-20 17:23 ` Vinod Koul
2019-08-20 17:23 ` [PATCH v3 7/8] arm64: dts: qcom: sm8150: Add reserved-memory regions Vinod Koul
` (2 subsequent siblings)
9 siblings, 0 replies; 14+ messages in thread
From: Vinod Koul @ 2019-08-20 17:23 UTC (permalink / raw)
To: Andy Gross
Cc: linux-arm-msm, Bjorn Andersson, Vinod Koul, Rob Herring,
Mark Rutland, Stephen Boyd, Sibi Sankar, devicetree,
linux-kernel
Add the regulators found in the mtp platform. This platform consists of
pmic PM8150, PM8150L and PM8009.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/sm8150-mtp.dts | 327 ++++++++++++++++++++++++
1 file changed, 327 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8150-mtp.dts b/arch/arm64/boot/dts/qcom/sm8150-mtp.dts
index 6f5777f530ae..340d57cc62bf 100644
--- a/arch/arm64/boot/dts/qcom/sm8150-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8150-mtp.dts
@@ -6,6 +6,7 @@
/dts-v1/;
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include "sm8150.dtsi"
#include "pm8150.dtsi"
#include "pm8150b.dtsi"
@@ -22,6 +23,332 @@
chosen {
stdout-path = "serial0:115200n8";
};
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ };
+
+ /*
+ * Apparently RPMh does not provide support for PM8150 S4 because it
+ * is always-on; model it as a fixed regulator.
+ */
+ vreg_s4a_1p8: pm8150-s4 {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_s4a_1p8";
+
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+
+ vin-supply = <&vph_pwr>;
+ };
+};
+
+&apps_rsc {
+ pm8150-rpmh-regulators {
+ compatible = "qcom,pm8150-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+ vdd-s7-supply = <&vph_pwr>;
+ vdd-s8-supply = <&vph_pwr>;
+ vdd-s9-supply = <&vph_pwr>;
+ vdd-s10-supply = <&vph_pwr>;
+
+ vdd-l1-l8-l11-supply = <&vreg_s6a_0p9>;
+ vdd-l2-l10-supply = <&vreg_bob>;
+ vdd-l3-l4-l5-l18-supply = <&vreg_s6a_0p9>;
+ vdd-l6-l9-supply = <&vreg_s8c_1p3>;
+ vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p0>;
+ vdd-l13-l16-l17-supply = <&vreg_bob>;
+
+ vreg_s5a_2p0: smps5 {
+ regulator-min-microvolt = <1904000>;
+ regulator-max-microvolt = <2000000>;
+ };
+
+ vreg_s6a_0p9: smps6 {
+ regulator-min-microvolt = <920000>;
+ regulator-max-microvolt = <1128000>;
+ };
+
+ vdda_wcss_pll:
+ vreg_l1a_0p75: ldo1 {
+ regulator-min-microvolt = <752000>;
+ regulator-max-microvolt = <752000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vdd_pdphy:
+ vdda_usb_hs_3p1:
+ vreg_l2a_3p1: ldo2 {
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3a_0p8: ldo3 {
+ regulator-min-microvolt = <480000>;
+ regulator-max-microvolt = <932000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vdd_usb_hs_core:
+ vdda_csi_0_0p9:
+ vdda_csi_1_0p9:
+ vdda_csi_2_0p9:
+ vdda_csi_3_0p9:
+ vdda_dsi_0_0p9:
+ vdda_dsi_1_0p9:
+ vdda_dsi_0_pll_0p9:
+ vdda_dsi_1_pll_0p9:
+ vdda_pcie_1ln_core:
+ vdda_pcie_2ln_core:
+ vdda_pll_hv_cc_ebi01:
+ vdda_pll_hv_cc_ebi23:
+ vdda_qrefs_0p875_5:
+ vdda_sp_sensor:
+ vdda_ufs_2ln_core_1:
+ vdda_ufs_2ln_core_2:
+ vdda_usb_ss_dp_core_1:
+ vdda_usb_ss_dp_core_2:
+ vdda_qlink_lv:
+ vdda_qlink_lv_ck:
+ vreg_l5a_0p875: ldo5 {
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6a_1p2: ldo6 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7a_1p8: ldo7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vddpx_10:
+ vreg_l9a_1p2: ldo9 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+
+ vreg_l10a_2p5: ldo10 {
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11a_0p8: ldo11 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vdd_qfprom:
+ vdd_qfprom_sp:
+ vdda_apc_cs_1p8:
+ vdda_gfx_cs_1p8:
+ vdda_usb_hs_1p8:
+ vdda_qrefs_vref_1p8:
+ vddpx_10_a:
+ vreg_l12a_1p8: ldo12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l13a_2p7: ldo13 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2704000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l14a_1p8: ldo14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l15a_1p7: ldo15 {
+ regulator-min-microvolt = <1704000>;
+ regulator-max-microvolt = <1704000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l16a_2p7: ldo16 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l17a_3p0: ldo17 {
+ regulator-min-microvolt = <2856000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ pm8150l-rpmh-regulators {
+ compatible = "qcom,pm8150l-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+ vdd-s7-supply = <&vph_pwr>;
+ vdd-s8-supply = <&vph_pwr>;
+
+ vdd-l1-l8-supply = <&vreg_s4a_1p8>;
+ vdd-l2-l3-supply = <&vreg_s8c_1p3>;
+ vdd-l4-l5-l6-supply = <&vreg_bob>;
+ vdd-l7-l11-supply = <&vreg_bob>;
+ vdd-l9-l10-supply = <&vreg_bob>;
+
+ vdd-bob-supply = <&vph_pwr>;
+ vdd-flash-supply = <&vreg_bob>;
+ vdd-rgb-supply = <&vreg_bob>;
+
+ vreg_bob: bob {
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <4000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+ regulator-allow-bypass;
+ };
+
+ vreg_s8c_1p3: smps8 {
+ regulator-min-microvolt = <1352000>;
+ regulator-max-microvolt = <1352000>;
+ };
+
+ vreg_l1c_1p8: ldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vdda_wcss_adcdac_1:
+ vdda_wcss_adcdac_22:
+ vreg_l2c_1p3: ldo2 {
+ regulator-min-microvolt = <1304000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vdda_hv_ebi0:
+ vdda_hv_ebi1:
+ vdda_hv_ebi2:
+ vdda_hv_ebi3:
+ vdda_hv_refgen0:
+ vdda_qlink_hv_ck:
+ vreg_l3c_1p2: ldo3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vddpx_5:
+ vreg_l4c_1p8: ldo4 {
+ regulator-min-microvolt = <1704000>;
+ regulator-max-microvolt = <2928000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vddpx_6:
+ vreg_l5c_1p8: ldo5 {
+ regulator-min-microvolt = <1704000>;
+ regulator-max-microvolt = <2928000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vddpx_2:
+ vreg_l6c_2p9: ldo6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7c_3p0: ldo7 {
+ regulator-min-microvolt = <2856000>;
+ regulator-max-microvolt = <3104000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8c_1p8: ldo8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9c_2p9: ldo9 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+
+ vreg_l10c_3p3: ldo10 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11c_3p3: ldo11 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ pm8009-rpmh-regulators {
+ compatible = "qcom,pm8009-rpmh-regulators";
+ qcom,pmic-id = "f";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vreg_bob>;
+
+ vdd-l2-supply = <&vreg_s8c_1p3>;
+ vdd-l5-l6-supply = <&vreg_bob>;
+
+ vreg_l2f_1p2: ldo2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5f_2p85: ldo5 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6f_2p85: ldo6 {
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-min-microvolt = <2856000>;
+ regulator-max-microvolt = <2856000>;
+ };
+ };
+
};
&qupv3_id_1 {
--
2.20.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v3 7/8] arm64: dts: qcom: sm8150: Add reserved-memory regions
2019-08-20 17:23 [PATCH v3 0/8] arm64: dts: qcom: sm8150: Add SM8150 DTS Vinod Koul
` (6 preceding siblings ...)
2019-08-20 17:23 ` [PATCH v3 6/8] arm64: dts: qcom: sm8150-mtp: Add regulators Vinod Koul
@ 2019-08-20 17:23 ` Vinod Koul
2019-08-20 17:23 ` [PATCH v3 8/8] arm64: dts: qcom: sm8150: Add apps shared nodes Vinod Koul
2019-08-21 9:06 ` [PATCH v3 0/8] arm64: dts: qcom: sm8150: Add SM8150 DTS Niklas Cassel
9 siblings, 0 replies; 14+ messages in thread
From: Vinod Koul @ 2019-08-20 17:23 UTC (permalink / raw)
To: Andy Gross
Cc: linux-arm-msm, Bjorn Andersson, Vinod Koul, Rob Herring,
Mark Rutland, Stephen Boyd, Sibi Sankar, devicetree,
linux-kernel
Add the reserved memory regions in SM8150
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/sm8150.dtsi | 111 +++++++++++++++++++++++++++
1 file changed, 111 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
index ba5a9f6332c1..3bed04d60dea 100644
--- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
@@ -155,6 +155,117 @@
method = "smc";
};
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ hyp_mem: memory@85700000 {
+ reg = <0x0 0x85700000 0x0 0x600000>;
+ no-map;
+ };
+
+ xbl_mem: memory@85d00000 {
+ reg = <0x0 0x85d00000 0x0 0x140000>;
+ no-map;
+ };
+
+ aop_mem: memory@85f00000 {
+ reg = <0x0 0x85f00000 0x0 0x20000>;
+ no-map;
+ };
+
+ aop_cmd_db: memory@85f20000 {
+ compatible = "qcom,cmd-db";
+ reg = <0x0 0x85f20000 0x0 0x20000>;
+ no-map;
+ };
+
+ smem_mem: memory@86000000 {
+ reg = <0x0 0x86000000 0x0 0x200000>;
+ no-map;
+ };
+
+ tz_mem: memory@86200000 {
+ reg = <0x0 0x86200000 0x0 0x3900000>;
+ no-map;
+ };
+
+ rmtfs_mem: memory@89b00000 {
+ compatible = "qcom,rmtfs-mem";
+ reg = <0x0 0x89b00000 0x0 0x200000>;
+ no-map;
+
+ qcom,client-id = <1>;
+ qcom,vmid = <15>;
+ };
+
+ camera_mem: memory@8b700000 {
+ reg = <0x0 0x8b700000 0x0 0x500000>;
+ no-map;
+ };
+
+ wlan_mem: memory@8bc00000 {
+ reg = <0x0 0x8bc00000 0x0 0x180000>;
+ no-map;
+ };
+
+ npu_mem: memory@8bd80000 {
+ reg = <0x0 0x8bd80000 0x0 0x80000>;
+ no-map;
+ };
+
+ adsp_mem: memory@8be00000 {
+ reg = <0x0 0x8be00000 0x0 0x1a00000>;
+ no-map;
+ };
+
+ mpss_mem: memory@8d800000 {
+ reg = <0x0 0x8d800000 0x0 0x9600000>;
+ no-map;
+ };
+
+ venus_mem: memory@96e00000 {
+ reg = <0x0 0x96e00000 0x0 0x500000>;
+ no-map;
+ };
+
+ slpi_mem: memory@97300000 {
+ reg = <0x0 0x97300000 0x0 0x1400000>;
+ no-map;
+ };
+
+ ipa_fw_mem: memory@98700000 {
+ reg = <0x0 0x98700000 0x0 0x10000>;
+ no-map;
+ };
+
+ ipa_gsi_mem: memory@98710000 {
+ reg = <0x0 0x98710000 0x0 0x5000>;
+ no-map;
+ };
+
+ gpu_mem: memory@98715000 {
+ reg = <0x0 0x98715000 0x0 0x2000>;
+ no-map;
+ };
+
+ spss_mem: memory@98800000 {
+ reg = <0x0 0x98800000 0x0 0x100000>;
+ no-map;
+ };
+
+ cdsp_mem: memory@98900000 {
+ reg = <0x0 0x98900000 0x0 0x1400000>;
+ no-map;
+ };
+
+ qseecom_mem: memory@9e400000 {
+ reg = <0x0 0x9e400000 0x0 0x1400000>;
+ no-map;
+ };
+ };
+
soc: soc@0 {
#address-cells = <1>;
#size-cells = <1>;
--
2.20.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v3 8/8] arm64: dts: qcom: sm8150: Add apps shared nodes
2019-08-20 17:23 [PATCH v3 0/8] arm64: dts: qcom: sm8150: Add SM8150 DTS Vinod Koul
` (7 preceding siblings ...)
2019-08-20 17:23 ` [PATCH v3 7/8] arm64: dts: qcom: sm8150: Add reserved-memory regions Vinod Koul
@ 2019-08-20 17:23 ` Vinod Koul
2019-08-21 8:43 ` Amit Kucheria
2019-08-21 9:06 ` [PATCH v3 0/8] arm64: dts: qcom: sm8150: Add SM8150 DTS Niklas Cassel
9 siblings, 1 reply; 14+ messages in thread
From: Vinod Koul @ 2019-08-20 17:23 UTC (permalink / raw)
To: Andy Gross
Cc: linux-arm-msm, Bjorn Andersson, Vinod Koul, Rob Herring,
Mark Rutland, Stephen Boyd, Sibi Sankar, devicetree,
linux-kernel
Add hwlock, pmu, smem, tcsr_mutex_regs, apss_shared mailbox, apps_rsc
including the rpmhcc child nodes to the SM8150 DTSI
Co-developed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/sm8150.dtsi | 63 ++++++++++++++++++++++++++++
1 file changed, 63 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
index 3bed04d60dea..781905e9977a 100644
--- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
@@ -144,12 +144,23 @@
};
};
+ tcsr_mutex: hwlock {
+ compatible = "qcom,tcsr-mutex";
+ syscon = <&tcsr_mutex_regs 0 0x1000>;
+ #hwlock-cells = <1>;
+ };
+
memory@80000000 {
device_type = "memory";
/* We expect the bootloader to fill in the size */
reg = <0x0 0x80000000 0x0 0x0>;
};
+ pmu {
+ compatible = "arm,armv8-pmuv3";
+ interrupts = <GIC_PPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
psci {
compatible = "arm,psci-1.0";
method = "smc";
@@ -266,6 +277,12 @@
};
};
+ smem {
+ compatible = "qcom,smem";
+ memory-region = <&smem_mem>;
+ hwlocks = <&tcsr_mutex 3>;
+ };
+
soc: soc@0 {
#address-cells = <1>;
#size-cells = <1>;
@@ -305,6 +322,11 @@
};
};
+ tcsr_mutex_regs: syscon@1f40000 {
+ compatible = "syscon";
+ reg = <0x01f40000 0x40000>;
+ };
+
tlmm: pinctrl@3100000 {
compatible = "qcom,sm8150-pinctrl";
reg = <0x03100000 0x300000>,
@@ -320,6 +342,16 @@
#interrupt-cells = <2>;
};
+ aoss_qmp: power-controller@c300000 {
+ compatible = "qcom,sm8150-aoss-qmp";
+ reg = <0x0c300000 0x100000>;
+ interrupts = <GIC_SPI 389 IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&apss_shared 0>;
+
+ #clock-cells = <0>;
+ #power-domain-cells = <1>;
+ };
+
intc: interrupt-controller@17a00000 {
compatible = "arm,gic-v3";
interrupt-controller;
@@ -329,6 +361,12 @@
interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
};
+ apss_shared: mailbox@17c00000 {
+ compatible = "qcom,sm8150-apss-shared";
+ reg = <0x17c00000 0x1000>;
+ #mbox-cells = <1>;
+ };
+
timer@17c20000 {
#address-cells = <1>;
#size-cells = <1>;
@@ -388,6 +426,31 @@
};
};
+ apps_rsc: rsc@18200000 {
+ label = "apps_rsc";
+ compatible = "qcom,rpmh-rsc";
+ reg = <0x18200000 0x10000>,
+ <0x18210000 0x10000>,
+ <0x18220000 0x10000>;
+ reg-names = "drv-0", "drv-1", "drv-2";
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ qcom,tcs-offset = <0xd00>;
+ qcom,drv-id = <2>;
+ qcom,tcs-config = <ACTIVE_TCS 2>,
+ <SLEEP_TCS 1>,
+ <WAKE_TCS 1>,
+ <CONTROL_TCS 0>;
+
+ rpmhcc: clock-controller {
+ compatible = "qcom,sm8150-rpmh-clk";
+ #clock-cells = <1>;
+ clock-names = "xo";
+ clocks = <&xo_board>;
+ };
+ };
+
spmi_bus: spmi@c440000 {
compatible = "qcom,spmi-pmic-arb";
reg = <0x0c440000 0x0001100>,
--
2.20.1
^ permalink raw reply related [flat|nested] 14+ messages in thread* Re: [PATCH v3 8/8] arm64: dts: qcom: sm8150: Add apps shared nodes
2019-08-20 17:23 ` [PATCH v3 8/8] arm64: dts: qcom: sm8150: Add apps shared nodes Vinod Koul
@ 2019-08-21 8:43 ` Amit Kucheria
2019-08-21 18:03 ` Vinod Koul
0 siblings, 1 reply; 14+ messages in thread
From: Amit Kucheria @ 2019-08-21 8:43 UTC (permalink / raw)
To: Vinod Koul
Cc: Andy Gross, linux-arm-msm, Bjorn Andersson, Rob Herring,
Mark Rutland, Stephen Boyd, Sibi Sankar,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, LKML
On Tue, Aug 20, 2019 at 10:55 PM Vinod Koul <vkoul@kernel.org> wrote:
>
> Add hwlock, pmu, smem, tcsr_mutex_regs, apss_shared mailbox, apps_rsc
> including the rpmhcc child nodes to the SM8150 DTSI
>
> Co-developed-by: Sibi Sankar <sibis@codeaurora.org>
> Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> ---
> arch/arm64/boot/dts/qcom/sm8150.dtsi | 63 ++++++++++++++++++++++++++++
> 1 file changed, 63 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
> index 3bed04d60dea..781905e9977a 100644
> --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
> @@ -144,12 +144,23 @@
> };
> };
>
> + tcsr_mutex: hwlock {
> + compatible = "qcom,tcsr-mutex";
> + syscon = <&tcsr_mutex_regs 0 0x1000>;
> + #hwlock-cells = <1>;
> + };
> +
> memory@80000000 {
> device_type = "memory";
> /* We expect the bootloader to fill in the size */
> reg = <0x0 0x80000000 0x0 0x0>;
> };
>
> + pmu {
> + compatible = "arm,armv8-pmuv3";
> + interrupts = <GIC_PPI 5 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> psci {
> compatible = "arm,psci-1.0";
> method = "smc";
> @@ -266,6 +277,12 @@
> };
> };
>
> + smem {
> + compatible = "qcom,smem";
> + memory-region = <&smem_mem>;
> + hwlocks = <&tcsr_mutex 3>;
> + };
> +
> soc: soc@0 {
> #address-cells = <1>;
> #size-cells = <1>;
> @@ -305,6 +322,11 @@
> };
> };
>
> + tcsr_mutex_regs: syscon@1f40000 {
> + compatible = "syscon";
> + reg = <0x01f40000 0x40000>;
> + };
> +
> tlmm: pinctrl@3100000 {
> compatible = "qcom,sm8150-pinctrl";
> reg = <0x03100000 0x300000>,
> @@ -320,6 +342,16 @@
> #interrupt-cells = <2>;
> };
>
> + aoss_qmp: power-controller@c300000 {
> + compatible = "qcom,sm8150-aoss-qmp";
> + reg = <0x0c300000 0x100000>;
> + interrupts = <GIC_SPI 389 IRQ_TYPE_EDGE_RISING>;
> + mboxes = <&apss_shared 0>;
> +
> + #clock-cells = <0>;
> + #power-domain-cells = <1>;
> + };
> +
> intc: interrupt-controller@17a00000 {
> compatible = "arm,gic-v3";
> interrupt-controller;
> @@ -329,6 +361,12 @@
> interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
> };
>
> + apss_shared: mailbox@17c00000 {
> + compatible = "qcom,sm8150-apss-shared";
> + reg = <0x17c00000 0x1000>;
> + #mbox-cells = <1>;
> + };
> +
> timer@17c20000 {
> #address-cells = <1>;
> #size-cells = <1>;
> @@ -388,6 +426,31 @@
> };
> };
>
> + apps_rsc: rsc@18200000 {
> + label = "apps_rsc";
> + compatible = "qcom,rpmh-rsc";
> + reg = <0x18200000 0x10000>,
> + <0x18210000 0x10000>,
> + <0x18220000 0x10000>;
> + reg-names = "drv-0", "drv-1", "drv-2";
> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> + qcom,tcs-offset = <0xd00>;
> + qcom,drv-id = <2>;
> + qcom,tcs-config = <ACTIVE_TCS 2>,
> + <SLEEP_TCS 1>,
> + <WAKE_TCS 1>,
> + <CONTROL_TCS 0>;
> +
> + rpmhcc: clock-controller {
> + compatible = "qcom,sm8150-rpmh-clk";
> + #clock-cells = <1>;
> + clock-names = "xo";
> + clocks = <&xo_board>;
> + };
> + };
> +
> spmi_bus: spmi@c440000 {
Sort by address here.
> compatible = "qcom,spmi-pmic-arb";
> reg = <0x0c440000 0x0001100>,
> --
> 2.20.1
>
^ permalink raw reply [flat|nested] 14+ messages in thread* Re: [PATCH v3 8/8] arm64: dts: qcom: sm8150: Add apps shared nodes
2019-08-21 8:43 ` Amit Kucheria
@ 2019-08-21 18:03 ` Vinod Koul
0 siblings, 0 replies; 14+ messages in thread
From: Vinod Koul @ 2019-08-21 18:03 UTC (permalink / raw)
To: Amit Kucheria
Cc: Andy Gross, linux-arm-msm, Bjorn Andersson, Rob Herring,
Mark Rutland, Stephen Boyd, Sibi Sankar,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, LKML
On 21-08-19, 14:13, Amit Kucheria wrote:
> On Tue, Aug 20, 2019 at 10:55 PM Vinod Koul <vkoul@kernel.org> wrote:
> >
> > Add hwlock, pmu, smem, tcsr_mutex_regs, apss_shared mailbox, apps_rsc
> > including the rpmhcc child nodes to the SM8150 DTSI
> > +
> > spmi_bus: spmi@c440000 {
>
> Sort by address here.
Yes will fix, thanks for spotting!
--
~Vinod
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v3 0/8] arm64: dts: qcom: sm8150: Add SM8150 DTS
2019-08-20 17:23 [PATCH v3 0/8] arm64: dts: qcom: sm8150: Add SM8150 DTS Vinod Koul
` (8 preceding siblings ...)
2019-08-20 17:23 ` [PATCH v3 8/8] arm64: dts: qcom: sm8150: Add apps shared nodes Vinod Koul
@ 2019-08-21 9:06 ` Niklas Cassel
9 siblings, 0 replies; 14+ messages in thread
From: Niklas Cassel @ 2019-08-21 9:06 UTC (permalink / raw)
To: Vinod Koul
Cc: Andy Gross, linux-arm-msm, Bjorn Andersson, Rob Herring,
Mark Rutland, Stephen Boyd, Sibi Sankar, devicetree,
linux-kernel
On Tue, Aug 20, 2019 at 10:53:42PM +0530, Vinod Koul wrote:
> This series adds DTS for SM8150, PMIC PM8150, PM8150B, PM8150L and
> the MTP for SM8150.
>
> Changes in v3:
> - Fix copyright comment style to Linux kernel style
> - Make property values all hex or decimal
> - Fix patch titles and logs and make them consistent
> - Fix line breaks
>
> Changes in v2:
> - Squash patches
> - Fix comments given by Stephen namely, lowercase for hext numbers,
> making rpmhcc have xo_board as parent, rename pon controller to
> power-on controller, make pmic nodes as disabled etc.
> - removed the dependency on clk defines and use raw numbers
>
>
> Vinod Koul (8):
> arm64: dts: qcom: sm8150: Add base dts file
> arm64: dts: qcom: pm8150: Add base dts file
> arm64: dts: qcom: pm8150b: Add base dts file
> arm64: dts: qcom: pm8150l: Add base dts file
> arm64: dts: qcom: sm8150-mtp: Add base dts file
> arm64: dts: qcom: sm8150-mtp: Add regulators
> arm64: dts: qcom: sm8150: Add reserved-memory regions
> arm64: dts: qcom: sm8150: Add apps shared nodes
>
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> arch/arm64/boot/dts/qcom/pm8150.dtsi | 97 +++++
> arch/arm64/boot/dts/qcom/pm8150b.dtsi | 86 +++++
> arch/arm64/boot/dts/qcom/pm8150l.dtsi | 80 ++++
> arch/arm64/boot/dts/qcom/sm8150-mtp.dts | 378 +++++++++++++++++++
> arch/arm64/boot/dts/qcom/sm8150.dtsi | 481 ++++++++++++++++++++++++
> 6 files changed, 1123 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/pm8150.dtsi
> create mode 100644 arch/arm64/boot/dts/qcom/pm8150b.dtsi
> create mode 100644 arch/arm64/boot/dts/qcom/pm8150l.dtsi
> create mode 100644 arch/arm64/boot/dts/qcom/sm8150-mtp.dts
> create mode 100644 arch/arm64/boot/dts/qcom/sm8150.dtsi
>
> --
> 2.20.1
>
Whole series is:
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
^ permalink raw reply [flat|nested] 14+ messages in thread