Linux-ARM-MSM Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH v2] drm/msm/dsi: Implement reset correctly
@ 2019-10-11 13:39 Jeffrey Hugo
  2019-10-11 18:07 ` Sean Paul
  0 siblings, 1 reply; 2+ messages in thread
From: Jeffrey Hugo @ 2019-10-11 13:39 UTC (permalink / raw)
  To: robdclark, sean, airlied, daniel
  Cc: linux-arm-msm, dri-devel, freedreno, linux-kernel, Jeffrey Hugo

On msm8998, vblank timeouts are observed because the DSI controller is not
reset properly, which ends up stalling the MDP.  This is because the reset
logic is not correct per the hardware documentation.

The documentation states that after asserting reset, software should wait
some time (no indication of how long), or poll the status register until it
returns 0 before deasserting reset.

wmb() is insufficient for this purpose since it just ensures ordering, not
timing between writes.  Since asserting and deasserting reset occurs on the
same register, ordering is already guaranteed by the architecture, making
the wmb extraneous.

Since we would define a timeout for polling the status register to avoid a
possible infinite loop, lets just use a static delay of 20 ms, since 16.666
ms is the time available to process one frame at 60 fps.

Fixes: a689554ba6ed (drm/msm: Initial add DSI connector support)
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Sean Paul <sean@poorly.run>
---

v2:
-make a DEFINE for the delay

 drivers/gpu/drm/msm/dsi/dsi_host.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/msm/dsi/dsi_host.c b/drivers/gpu/drm/msm/dsi/dsi_host.c
index 663ff9f4fac9..9a81705301c6 100644
--- a/drivers/gpu/drm/msm/dsi/dsi_host.c
+++ b/drivers/gpu/drm/msm/dsi/dsi_host.c
@@ -26,6 +26,8 @@
 #include "dsi_cfg.h"
 #include "msm_kms.h"
 
+#define RESET_DELAY 20
+
 static int dsi_get_version(const void __iomem *base, u32 *major, u32 *minor)
 {
 	u32 ver;
@@ -986,7 +988,7 @@ static void dsi_sw_reset(struct msm_dsi_host *msm_host)
 	wmb(); /* clocks need to be enabled before reset */
 
 	dsi_write(msm_host, REG_DSI_RESET, 1);
-	wmb(); /* make sure reset happen */
+	msleep(RESET_DELAY); /* make sure reset happen */
 	dsi_write(msm_host, REG_DSI_RESET, 0);
 }
 
@@ -1396,7 +1398,7 @@ static void dsi_sw_reset_restore(struct msm_dsi_host *msm_host)
 
 	/* dsi controller can only be reset while clocks are running */
 	dsi_write(msm_host, REG_DSI_RESET, 1);
-	wmb();	/* make sure reset happen */
+	msleep(RESET_DELAY);	/* make sure reset happen */
 	dsi_write(msm_host, REG_DSI_RESET, 0);
 	wmb();	/* controller out of reset */
 	dsi_write(msm_host, REG_DSI_CTRL, data0);
-- 
2.17.1


^ permalink raw reply	[flat|nested] 2+ messages in thread

* Re: [PATCH v2] drm/msm/dsi: Implement reset correctly
  2019-10-11 13:39 [PATCH v2] drm/msm/dsi: Implement reset correctly Jeffrey Hugo
@ 2019-10-11 18:07 ` Sean Paul
  0 siblings, 0 replies; 2+ messages in thread
From: Sean Paul @ 2019-10-11 18:07 UTC (permalink / raw)
  To: Jeffrey Hugo
  Cc: robdclark, sean, airlied, daniel, linux-arm-msm, dri-devel,
	freedreno, linux-kernel

On Fri, Oct 11, 2019 at 06:39:39AM -0700, Jeffrey Hugo wrote:
> On msm8998, vblank timeouts are observed because the DSI controller is not
> reset properly, which ends up stalling the MDP.  This is because the reset
> logic is not correct per the hardware documentation.
> 
> The documentation states that after asserting reset, software should wait
> some time (no indication of how long), or poll the status register until it
> returns 0 before deasserting reset.
> 
> wmb() is insufficient for this purpose since it just ensures ordering, not
> timing between writes.  Since asserting and deasserting reset occurs on the
> same register, ordering is already guaranteed by the architecture, making
> the wmb extraneous.
> 
> Since we would define a timeout for polling the status register to avoid a
> possible infinite loop, lets just use a static delay of 20 ms, since 16.666
> ms is the time available to process one frame at 60 fps.
> 
> Fixes: a689554ba6ed (drm/msm: Initial add DSI connector support)
> Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>

Pushed to drm-misc-fixes for 5.4

Thanks!

Sean

> Reviewed-by: Sean Paul <sean@poorly.run>
> ---
> 
> v2:
> -make a DEFINE for the delay
> 
>  drivers/gpu/drm/msm/dsi/dsi_host.c | 6 ++++--
>  1 file changed, 4 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/gpu/drm/msm/dsi/dsi_host.c b/drivers/gpu/drm/msm/dsi/dsi_host.c
> index 663ff9f4fac9..9a81705301c6 100644
> --- a/drivers/gpu/drm/msm/dsi/dsi_host.c
> +++ b/drivers/gpu/drm/msm/dsi/dsi_host.c
> @@ -26,6 +26,8 @@
>  #include "dsi_cfg.h"
>  #include "msm_kms.h"
>  
> +#define RESET_DELAY 20
> +
>  static int dsi_get_version(const void __iomem *base, u32 *major, u32 *minor)
>  {
>  	u32 ver;
> @@ -986,7 +988,7 @@ static void dsi_sw_reset(struct msm_dsi_host *msm_host)
>  	wmb(); /* clocks need to be enabled before reset */
>  
>  	dsi_write(msm_host, REG_DSI_RESET, 1);
> -	wmb(); /* make sure reset happen */
> +	msleep(RESET_DELAY); /* make sure reset happen */
>  	dsi_write(msm_host, REG_DSI_RESET, 0);
>  }
>  
> @@ -1396,7 +1398,7 @@ static void dsi_sw_reset_restore(struct msm_dsi_host *msm_host)
>  
>  	/* dsi controller can only be reset while clocks are running */
>  	dsi_write(msm_host, REG_DSI_RESET, 1);
> -	wmb();	/* make sure reset happen */
> +	msleep(RESET_DELAY);	/* make sure reset happen */
>  	dsi_write(msm_host, REG_DSI_RESET, 0);
>  	wmb();	/* controller out of reset */
>  	dsi_write(msm_host, REG_DSI_CTRL, data0);
> -- 
> 2.17.1
> 

-- 
Sean Paul, Software Engineer, Google / Chromium OS

^ permalink raw reply	[flat|nested] 2+ messages in thread

end of thread, back to index

Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-10-11 13:39 [PATCH v2] drm/msm/dsi: Implement reset correctly Jeffrey Hugo
2019-10-11 18:07 ` Sean Paul

Linux-ARM-MSM Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-arm-msm/0 linux-arm-msm/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-arm-msm linux-arm-msm/ https://lore.kernel.org/linux-arm-msm \
		linux-arm-msm@vger.kernel.org
	public-inbox-index linux-arm-msm

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-arm-msm


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git