From: Guenter Roeck <linux@roeck-us.net>
To: Ansuel Smith <ansuelsmth@gmail.com>
Cc: Andy Gross <agross@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Wim Van Sebroeck <wim@linux-watchdog.org>,
linux-arm-msm@vger.kernel.org, linux-watchdog@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH v2] watchdog: qcom-wdt: disable pretimeout on timer platform
Date: Tue, 4 Feb 2020 12:55:59 -0800 [thread overview]
Message-ID: <20200204205559.GA28502@roeck-us.net> (raw)
In-Reply-To: <20200204195648.23350-1-ansuelsmth@gmail.com>
On Tue, Feb 04, 2020 at 08:56:48PM +0100, Ansuel Smith wrote:
> Some platform like ipq806x doesn't support pretimeout and define
> some interrupts used by qcom,msm-timer. Change the driver to check
> and use pretimeout only on qcom,kpss-wdt as it's the only platform
> that actually supports it.
>
> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
> ---
> drivers/watchdog/qcom-wdt.c | 31 +++++++++++++++++++++++--------
> 1 file changed, 23 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/watchdog/qcom-wdt.c b/drivers/watchdog/qcom-wdt.c
> index a494543d3ae1..d13c75028985 100644
> --- a/drivers/watchdog/qcom-wdt.c
> +++ b/drivers/watchdog/qcom-wdt.c
> @@ -40,6 +40,11 @@ static const u32 reg_offset_data_kpss[] = {
> [WDT_BITE_TIME] = 0x14,
> };
>
> +struct qcom_wdt_match_data {
> + const u32 *offset;
> + bool pretimeout;
> +};
> +
> struct qcom_wdt {
> struct watchdog_device wdd;
> unsigned long rate;
> @@ -179,19 +184,29 @@ static void qcom_clk_disable_unprepare(void *data)
> clk_disable_unprepare(data);
> }
>
> +static const struct qcom_wdt_match_data match_data_apcs_tmr = {
> + .offset = reg_offset_data_apcs_tmr,
> + .pretimeout = false,
> +};
> +
> +static const struct qcom_wdt_match_data match_data_kpss = {
> + .offset = reg_offset_data_kpss,
> + .pretimeout = true,
> +};
> +
> static int qcom_wdt_probe(struct platform_device *pdev)
> {
> struct device *dev = &pdev->dev;
> struct qcom_wdt *wdt;
> struct resource *res;
> struct device_node *np = dev->of_node;
> - const u32 *regs;
> + const struct qcom_wdt_match_data *data;
> u32 percpu_offset;
> int irq, ret;
> struct clk *clk;
>
> - regs = of_device_get_match_data(dev);
> - if (!regs) {
> + data = of_device_get_match_data(dev);
> + if (!data) {
> dev_err(dev, "Unsupported QCOM WDT module\n");
> return -ENODEV;
> }
> @@ -247,7 +262,7 @@ static int qcom_wdt_probe(struct platform_device *pdev)
>
> /* check if there is pretimeout support */
> irq = platform_get_irq(pdev, 0);
> - if (irq > 0) {
> + if (data->pretimeout && irq > 0) {
> ret = devm_request_irq(dev, irq, qcom_wdt_isr,
> IRQF_TRIGGER_RISING,
> "wdt_bark", &wdt->wdd);
> @@ -267,7 +282,7 @@ static int qcom_wdt_probe(struct platform_device *pdev)
> wdt->wdd.min_timeout = 1;
> wdt->wdd.max_timeout = 0x10000000U / wdt->rate;
> wdt->wdd.parent = dev;
> - wdt->layout = regs;
> + wdt->layout = data->offset;
>
> if (readl(wdt_addr(wdt, WDT_STS)) & 1)
> wdt->wdd.bootstatus = WDIOF_CARDRESET;
> @@ -311,9 +326,9 @@ static int __maybe_unused qcom_wdt_resume(struct device *dev)
> static SIMPLE_DEV_PM_OPS(qcom_wdt_pm_ops, qcom_wdt_suspend, qcom_wdt_resume);
>
> static const struct of_device_id qcom_wdt_of_table[] = {
> - { .compatible = "qcom,kpss-timer", .data = reg_offset_data_apcs_tmr },
> - { .compatible = "qcom,scss-timer", .data = reg_offset_data_apcs_tmr },
> - { .compatible = "qcom,kpss-wdt", .data = reg_offset_data_kpss },
> + { .compatible = "qcom,kpss-timer", .data = &match_data_apcs_tmr },
> + { .compatible = "qcom,scss-timer", .data = &match_data_apcs_tmr },
> + { .compatible = "qcom,kpss-wdt", .data = &match_data_kpss },
> { },
> };
> MODULE_DEVICE_TABLE(of, qcom_wdt_of_table);
> --
> 2.24.0
>
prev parent reply other threads:[~2020-02-04 20:56 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-02-04 19:56 [PATCH v2] watchdog: qcom-wdt: disable pretimeout on timer platform Ansuel Smith
2020-02-04 20:55 ` Guenter Roeck [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200204205559.GA28502@roeck-us.net \
--to=linux@roeck-us.net \
--cc=agross@kernel.org \
--cc=ansuelsmth@gmail.com \
--cc=bjorn.andersson@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-watchdog@vger.kernel.org \
--cc=wim@linux-watchdog.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).