Linux-ARM-MSM Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH v2] pinctrl: qcom: use scm_call to route GPIO irq to Apps
@ 2020-03-26 17:35 Ansuel Smith
  2020-03-27 20:13 ` Bjorn Andersson
  0 siblings, 1 reply; 4+ messages in thread
From: Ansuel Smith @ 2020-03-26 17:35 UTC (permalink / raw)
  To: Andy Gross
  Cc: Ajay Kishore, Ansuel Smith, Bjorn Andersson, Linus Walleij,
	linux-arm-msm, linux-gpio, linux-kernel

From: Ajay Kishore <akisho@codeaurora.org>

For IPQ806x targets, TZ protects the registers that are used to
configure the routing of interrupts to a target processor.
To resolve this, this patch uses scm call to route GPIO interrupts
to application processor. Also the scm call interface is changed.

Signed-off-by: Ajay Kishore <akisho@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
---
v2:
* Move static varibale in msm_pinctrl struct
* Revert '4b024225c4a8 ("pinctrl: use devm_platform_ioremap_resource() to simplify code")'
  to get base_reg addr

 drivers/pinctrl/qcom/pinctrl-msm.c | 37 ++++++++++++++++++++++++++----
 1 file changed, 32 insertions(+), 5 deletions(-)

diff --git a/drivers/pinctrl/qcom/pinctrl-msm.c b/drivers/pinctrl/qcom/pinctrl-msm.c
index 9a8daa256a32..9627ebd41ff9 100644
--- a/drivers/pinctrl/qcom/pinctrl-msm.c
+++ b/drivers/pinctrl/qcom/pinctrl-msm.c
@@ -22,6 +22,8 @@
 #include <linux/reboot.h>
 #include <linux/pm.h>
 #include <linux/log2.h>
+#include <linux/qcom_scm.h>
+#include <linux/io.h>
 
 #include <linux/soc/qcom/irq.h>
 
@@ -60,6 +62,9 @@ struct msm_pinctrl {
 	struct irq_chip irq_chip;
 	int irq;
 
+	int route_to_apps;
+	u32 base_reg;
+
 	raw_spinlock_t lock;
 
 	DECLARE_BITMAP(dual_edge_irqs, MAX_NR_GPIO);
@@ -883,10 +888,27 @@ static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int type)
 		clear_bit(d->hwirq, pctrl->dual_edge_irqs);
 
 	/* Route interrupts to application cpu */
-	val = msm_readl_intr_target(pctrl, g);
-	val &= ~(7 << g->intr_target_bit);
-	val |= g->intr_target_kpss_val << g->intr_target_bit;
-	msm_writel_intr_target(val, pctrl, g);
+	if (pctrl->route_to_apps && pctrl->base_reg) {
+		u32 addr = pctrl->base_reg + g->intr_target_reg;
+		int ret;
+
+		qcom_scm_io_readl(addr, &val);
+
+		val &= ~(7 << g->intr_target_bit);
+		val |= g->intr_target_kpss_val << g->intr_target_bit;
+
+		ret = qcom_scm_io_writel(addr, val);
+		if (ret)
+			dev_err(pctrl->dev,
+				"Failed routing %lu interrupt to Apps proc",
+				d->hwirq);
+		}
+	} else {
+		val = msm_readl_intr_target(pctrl, g);
+		val &= ~(7 << g->intr_target_bit);
+		val |= g->intr_target_kpss_val << g->intr_target_bit;
+		msm_writel_intr_target(val, pctrl, g);
+	}
 
 	/* Update configuration for gpio.
 	 * RAW_STATUS_EN is left on for all gpio irqs. Due to the
@@ -1241,6 +1263,8 @@ int msm_pinctrl_probe(struct platform_device *pdev,
 	pctrl->dev = &pdev->dev;
 	pctrl->soc = soc_data;
 	pctrl->chip = msm_gpio_template;
+	pctrl->route_to_apps = of_device_is_compatible(pctrl->dev->of_node,
+					"qcom,ipq8064-pinctrl");
 
 	raw_spin_lock_init(&pctrl->lock);
 
@@ -1253,9 +1277,12 @@ int msm_pinctrl_probe(struct platform_device *pdev,
 				return PTR_ERR(pctrl->regs[i]);
 		}
 	} else {
-		pctrl->regs[0] = devm_platform_ioremap_resource(pdev, 0);
+		res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+		pctrl->regs[0] = devm_ioremap_resource(&pdev->dev, res);
 		if (IS_ERR(pctrl->regs[0]))
 			return PTR_ERR(pctrl->regs[0]);
+		else
+			pctrl->base_reg = res->start;
 	}
 
 	msm_pinctrl_setup_pm_reset(pctrl);
-- 
2.25.1


^ permalink raw reply	[flat|nested] 4+ messages in thread

* Re: [PATCH v2] pinctrl: qcom: use scm_call to route GPIO irq to Apps
  2020-03-26 17:35 [PATCH v2] pinctrl: qcom: use scm_call to route GPIO irq to Apps Ansuel Smith
@ 2020-03-27 20:13 ` Bjorn Andersson
  2020-03-27 20:58   ` R: " ansuelsmth
  0 siblings, 1 reply; 4+ messages in thread
From: Bjorn Andersson @ 2020-03-27 20:13 UTC (permalink / raw)
  To: Ansuel Smith
  Cc: Andy Gross, Ajay Kishore, Linus Walleij, linux-arm-msm,
	linux-gpio, linux-kernel

On Thu 26 Mar 10:35 PDT 2020, Ansuel Smith wrote:

> From: Ajay Kishore <akisho@codeaurora.org>
> 
> For IPQ806x targets, TZ protects the registers that are used to
> configure the routing of interrupts to a target processor.
> To resolve this, this patch uses scm call to route GPIO interrupts
> to application processor. Also the scm call interface is changed.
> 
> Signed-off-by: Ajay Kishore <akisho@codeaurora.org>
> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>

Thanks for respinning this Ansuel, just some minor things below.

> ---
> v2:
> * Move static varibale in msm_pinctrl struct
> * Revert '4b024225c4a8 ("pinctrl: use devm_platform_ioremap_resource() to simplify code")'
>   to get base_reg addr
> 
>  drivers/pinctrl/qcom/pinctrl-msm.c | 37 ++++++++++++++++++++++++++----
>  1 file changed, 32 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/pinctrl/qcom/pinctrl-msm.c b/drivers/pinctrl/qcom/pinctrl-msm.c
> index 9a8daa256a32..9627ebd41ff9 100644
> --- a/drivers/pinctrl/qcom/pinctrl-msm.c
> +++ b/drivers/pinctrl/qcom/pinctrl-msm.c
> @@ -22,6 +22,8 @@
>  #include <linux/reboot.h>
>  #include <linux/pm.h>
>  #include <linux/log2.h>
> +#include <linux/qcom_scm.h>
> +#include <linux/io.h>
>  
>  #include <linux/soc/qcom/irq.h>
>  
> @@ -60,6 +62,9 @@ struct msm_pinctrl {
>  	struct irq_chip irq_chip;
>  	int irq;
>  
> +	int route_to_apps;

We "always" route our interrupts to apps, so please rename this to
intr_target_use_scm. And using "bool" instead would make it clear that
this is a binary flag.

> +	u32 base_reg;

Even though I think it's fine that you only fill in the first entry,
please make this phys_base[MAX_NR_GPIO]; next to regs.

> +
>  	raw_spinlock_t lock;
>  
>  	DECLARE_BITMAP(dual_edge_irqs, MAX_NR_GPIO);
> @@ -883,10 +888,27 @@ static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int type)
>  		clear_bit(d->hwirq, pctrl->dual_edge_irqs);
>  
>  	/* Route interrupts to application cpu */
> -	val = msm_readl_intr_target(pctrl, g);
> -	val &= ~(7 << g->intr_target_bit);
> -	val |= g->intr_target_kpss_val << g->intr_target_bit;
> -	msm_writel_intr_target(val, pctrl, g);
> +	if (pctrl->route_to_apps && pctrl->base_reg) {

I meant that you could fill out "base_reg" only if it's supposed to be
used, but looking at your patch I think it's nicer to have a separate
flag - so you can omit the check for base_reg != NULL here.

> +		u32 addr = pctrl->base_reg + g->intr_target_reg;
> +		int ret;
> +
> +		qcom_scm_io_readl(addr, &val);
> +
> +		val &= ~(7 << g->intr_target_bit);
> +		val |= g->intr_target_kpss_val << g->intr_target_bit;
> +
> +		ret = qcom_scm_io_writel(addr, val);
> +		if (ret)
> +			dev_err(pctrl->dev,
> +				"Failed routing %lu interrupt to Apps proc",
> +				d->hwirq);
> +		}
> +	} else {
> +		val = msm_readl_intr_target(pctrl, g);
> +		val &= ~(7 << g->intr_target_bit);
> +		val |= g->intr_target_kpss_val << g->intr_target_bit;
> +		msm_writel_intr_target(val, pctrl, g);
> +	}
>  
>  	/* Update configuration for gpio.
>  	 * RAW_STATUS_EN is left on for all gpio irqs. Due to the
> @@ -1241,6 +1263,8 @@ int msm_pinctrl_probe(struct platform_device *pdev,
>  	pctrl->dev = &pdev->dev;
>  	pctrl->soc = soc_data;
>  	pctrl->chip = msm_gpio_template;
> +	pctrl->route_to_apps = of_device_is_compatible(pctrl->dev->of_node,
> +					"qcom,ipq8064-pinctrl");
>  
>  	raw_spin_lock_init(&pctrl->lock);
>  
> @@ -1253,9 +1277,12 @@ int msm_pinctrl_probe(struct platform_device *pdev,
>  				return PTR_ERR(pctrl->regs[i]);
>  		}
>  	} else {
> -		pctrl->regs[0] = devm_platform_ioremap_resource(pdev, 0);
> +		res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +		pctrl->regs[0] = devm_ioremap_resource(&pdev->dev, res);
>  		if (IS_ERR(pctrl->regs[0]))
>  			return PTR_ERR(pctrl->regs[0]);
> +		else

No need for the else, as the "positive" case is a return.

Thank you,
Bjorn

> +			pctrl->base_reg = res->start;
>  	}
>  
>  	msm_pinctrl_setup_pm_reset(pctrl);
> -- 
> 2.25.1
> 

^ permalink raw reply	[flat|nested] 4+ messages in thread

* R: [PATCH v2] pinctrl: qcom: use scm_call to route GPIO irq to Apps
  2020-03-27 20:13 ` Bjorn Andersson
@ 2020-03-27 20:58   ` " ansuelsmth
  2020-03-27 21:51     ` Bjorn Andersson
  0 siblings, 1 reply; 4+ messages in thread
From: ansuelsmth @ 2020-03-27 20:58 UTC (permalink / raw)
  To: 'Bjorn Andersson'
  Cc: 'Andy Gross', 'Ajay Kishore',
	'Linus Walleij',
	linux-arm-msm, linux-gpio, linux-kernel

> On Thu 26 Mar 10:35 PDT 2020, Ansuel Smith wrote:
> 
> > From: Ajay Kishore <akisho@codeaurora.org>
> >
> > For IPQ806x targets, TZ protects the registers that are used to
> > configure the routing of interrupts to a target processor.
> > To resolve this, this patch uses scm call to route GPIO interrupts
> > to application processor. Also the scm call interface is changed.
> >
> > Signed-off-by: Ajay Kishore <akisho@codeaurora.org>
> > Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
> 
> Thanks for respinning this Ansuel, just some minor things below.
> 
> > ---
> > v2:
> > * Move static varibale in msm_pinctrl struct
> > * Revert '4b024225c4a8 ("pinctrl: use
> devm_platform_ioremap_resource() to simplify code")'
> >   to get base_reg addr
> >
> >  drivers/pinctrl/qcom/pinctrl-msm.c | 37
> ++++++++++++++++++++++++++----
> >  1 file changed, 32 insertions(+), 5 deletions(-)
> >
> > diff --git a/drivers/pinctrl/qcom/pinctrl-msm.c
> b/drivers/pinctrl/qcom/pinctrl-msm.c
> > index 9a8daa256a32..9627ebd41ff9 100644
> > --- a/drivers/pinctrl/qcom/pinctrl-msm.c
> > +++ b/drivers/pinctrl/qcom/pinctrl-msm.c
> > @@ -22,6 +22,8 @@
> >  #include <linux/reboot.h>
> >  #include <linux/pm.h>
> >  #include <linux/log2.h>
> > +#include <linux/qcom_scm.h>
> > +#include <linux/io.h>
> >
> >  #include <linux/soc/qcom/irq.h>
> >
> > @@ -60,6 +62,9 @@ struct msm_pinctrl {
> >  	struct irq_chip irq_chip;
> >  	int irq;
> >
> > +	int route_to_apps;
> 
> We "always" route our interrupts to apps, so please rename this to
> intr_target_use_scm. And using "bool" instead would make it clear that
> this is a binary flag.
> 

Will fix in v3

> > +	u32 base_reg;
> 
> Even though I think it's fine that you only fill in the first entry,
> please make this phys_base[MAX_NR_GPIO]; next to regs.
> 

If I understand correctly, I should replace base_reg with 
phys_base[MAX_NR_GPIO]
I think we should use MAX_NR_TILES instead of MAX_NR_GPIO
Wouldn't this be a waste of memory since only the base_reg will be needed?
I don't think there will be a soc with multiple tiles and the need to add
code 
in the loop function. (Also sorry for off-topic... since we have
soc_data->ntiles
why don't we use kmem allocation instead of statically use half empty
array?)

> > +
> >  	raw_spinlock_t lock;
> >
> >  	DECLARE_BITMAP(dual_edge_irqs, MAX_NR_GPIO);
> > @@ -883,10 +888,27 @@ static int msm_gpio_irq_set_type(struct
> irq_data *d, unsigned int type)
> >  		clear_bit(d->hwirq, pctrl->dual_edge_irqs);
> >
> >  	/* Route interrupts to application cpu */
> > -	val = msm_readl_intr_target(pctrl, g);
> > -	val &= ~(7 << g->intr_target_bit);
> > -	val |= g->intr_target_kpss_val << g->intr_target_bit;
> > -	msm_writel_intr_target(val, pctrl, g);
> > +	if (pctrl->route_to_apps && pctrl->base_reg) {
> 
> I meant that you could fill out "base_reg" only if it's supposed to be
> used, but looking at your patch I think it's nicer to have a separate
> flag - so you can omit the check for base_reg != NULL here.
> 

Since we return error if devm_ioremap_resource fails, it is good to only
check 
the route_to_apps as base_reg will be set for sure?

> > +		u32 addr = pctrl->base_reg + g->intr_target_reg;
> > +		int ret;
> > +
> > +		qcom_scm_io_readl(addr, &val);
> > +
> > +		val &= ~(7 << g->intr_target_bit);
> > +		val |= g->intr_target_kpss_val << g->intr_target_bit;
> > +
> > +		ret = qcom_scm_io_writel(addr, val);
> > +		if (ret)
> > +			dev_err(pctrl->dev,
> > +				"Failed routing %lu interrupt to Apps proc",
> > +				d->hwirq);
> > +		}
> > +	} else {
> > +		val = msm_readl_intr_target(pctrl, g);
> > +		val &= ~(7 << g->intr_target_bit);
> > +		val |= g->intr_target_kpss_val << g->intr_target_bit;
> > +		msm_writel_intr_target(val, pctrl, g);
> > +	}
> >
> >  	/* Update configuration for gpio.
> >  	 * RAW_STATUS_EN is left on for all gpio irqs. Due to the
> > @@ -1241,6 +1263,8 @@ int msm_pinctrl_probe(struct platform_device
> *pdev,
> >  	pctrl->dev = &pdev->dev;
> >  	pctrl->soc = soc_data;
> >  	pctrl->chip = msm_gpio_template;
> > +	pctrl->route_to_apps = of_device_is_compatible(pctrl->dev-
> >of_node,
> > +					"qcom,ipq8064-pinctrl");
> >
> >  	raw_spin_lock_init(&pctrl->lock);
> >
> > @@ -1253,9 +1277,12 @@ int msm_pinctrl_probe(struct
> platform_device *pdev,
> >  				return PTR_ERR(pctrl->regs[i]);
> >  		}
> >  	} else {
> > -		pctrl->regs[0] = devm_platform_ioremap_resource(pdev, 0);
> > +		res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > +		pctrl->regs[0] = devm_ioremap_resource(&pdev->dev, res);
> >  		if (IS_ERR(pctrl->regs[0]))
> >  			return PTR_ERR(pctrl->regs[0]);
> > +		else
> 
> No need for the else, as the "positive" case is a return.
> 

Will fix in v3

> Thank you,
> Bjorn
> 
> > +			pctrl->base_reg = res->start;
> >  	}
> >
> >  	msm_pinctrl_setup_pm_reset(pctrl);
> > --
> > 2.25.1
> >


^ permalink raw reply	[flat|nested] 4+ messages in thread

* Re: R: [PATCH v2] pinctrl: qcom: use scm_call to route GPIO irq to Apps
  2020-03-27 20:58   ` R: " ansuelsmth
@ 2020-03-27 21:51     ` Bjorn Andersson
  0 siblings, 0 replies; 4+ messages in thread
From: Bjorn Andersson @ 2020-03-27 21:51 UTC (permalink / raw)
  To: ansuelsmth
  Cc: 'Andy Gross', 'Ajay Kishore',
	'Linus Walleij',
	linux-arm-msm, linux-gpio, linux-kernel

On Fri 27 Mar 13:58 PDT 2020, ansuelsmth@gmail.com wrote:

> > On Thu 26 Mar 10:35 PDT 2020, Ansuel Smith wrote:
> > 
> > > From: Ajay Kishore <akisho@codeaurora.org>
> > >
> > > For IPQ806x targets, TZ protects the registers that are used to
> > > configure the routing of interrupts to a target processor.
> > > To resolve this, this patch uses scm call to route GPIO interrupts
> > > to application processor. Also the scm call interface is changed.
> > >
> > > Signed-off-by: Ajay Kishore <akisho@codeaurora.org>
> > > Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
> > 
> > Thanks for respinning this Ansuel, just some minor things below.
> > 
> > > ---
> > > v2:
> > > * Move static varibale in msm_pinctrl struct
> > > * Revert '4b024225c4a8 ("pinctrl: use
> > devm_platform_ioremap_resource() to simplify code")'
> > >   to get base_reg addr
> > >
> > >  drivers/pinctrl/qcom/pinctrl-msm.c | 37
> > ++++++++++++++++++++++++++----
> > >  1 file changed, 32 insertions(+), 5 deletions(-)
> > >
> > > diff --git a/drivers/pinctrl/qcom/pinctrl-msm.c
> > b/drivers/pinctrl/qcom/pinctrl-msm.c
> > > index 9a8daa256a32..9627ebd41ff9 100644
> > > --- a/drivers/pinctrl/qcom/pinctrl-msm.c
> > > +++ b/drivers/pinctrl/qcom/pinctrl-msm.c
> > > @@ -22,6 +22,8 @@
> > >  #include <linux/reboot.h>
> > >  #include <linux/pm.h>
> > >  #include <linux/log2.h>
> > > +#include <linux/qcom_scm.h>
> > > +#include <linux/io.h>
> > >
> > >  #include <linux/soc/qcom/irq.h>
> > >
> > > @@ -60,6 +62,9 @@ struct msm_pinctrl {
> > >  	struct irq_chip irq_chip;
> > >  	int irq;
> > >
> > > +	int route_to_apps;
> > 
> > We "always" route our interrupts to apps, so please rename this to
> > intr_target_use_scm. And using "bool" instead would make it clear that
> > this is a binary flag.
> > 
> 
> Will fix in v3
> 
> > > +	u32 base_reg;
> > 
> > Even though I think it's fine that you only fill in the first entry,
> > please make this phys_base[MAX_NR_GPIO]; next to regs.
> > 
> 
> If I understand correctly, I should replace base_reg with 
> phys_base[MAX_NR_GPIO]
> I think we should use MAX_NR_TILES instead of MAX_NR_GPIO

Yes of course, didn't pay attention to my autocomplete!

> Wouldn't this be a waste of memory since only the base_reg will be
> needed?  I don't think there will be a soc with multiple tiles and the
> need to add code in the loop function. (Also sorry for off-topic...
> since we have soc_data->ntiles why don't we use kmem allocation
> instead of statically use half empty array?)
> 

While I hope you're right, I think it looks better if it mimics the
overall design - at the expense of wasting 12 bytes.

> > > +
> > >  	raw_spinlock_t lock;
> > >
> > >  	DECLARE_BITMAP(dual_edge_irqs, MAX_NR_GPIO);
> > > @@ -883,10 +888,27 @@ static int msm_gpio_irq_set_type(struct
> > irq_data *d, unsigned int type)
> > >  		clear_bit(d->hwirq, pctrl->dual_edge_irqs);
> > >
> > >  	/* Route interrupts to application cpu */
> > > -	val = msm_readl_intr_target(pctrl, g);
> > > -	val &= ~(7 << g->intr_target_bit);
> > > -	val |= g->intr_target_kpss_val << g->intr_target_bit;
> > > -	msm_writel_intr_target(val, pctrl, g);
> > > +	if (pctrl->route_to_apps && pctrl->base_reg) {
> > 
> > I meant that you could fill out "base_reg" only if it's supposed to be
> > used, but looking at your patch I think it's nicer to have a separate
> > flag - so you can omit the check for base_reg != NULL here.
> > 
> 
> Since we return error if devm_ioremap_resource fails, it is good to only
> check 
> the route_to_apps as base_reg will be set for sure?
> 

Right.

My initial suggestion was that base != NULL would have the meaning of
intr_target_use_scm. But what I meant here is that after looking at your
patch I think one flag and a separate base is better.

Thanks,
Bjorn

> > > +		u32 addr = pctrl->base_reg + g->intr_target_reg;
> > > +		int ret;
> > > +
> > > +		qcom_scm_io_readl(addr, &val);
> > > +
> > > +		val &= ~(7 << g->intr_target_bit);
> > > +		val |= g->intr_target_kpss_val << g->intr_target_bit;
> > > +
> > > +		ret = qcom_scm_io_writel(addr, val);
> > > +		if (ret)
> > > +			dev_err(pctrl->dev,
> > > +				"Failed routing %lu interrupt to Apps proc",
> > > +				d->hwirq);
> > > +		}
> > > +	} else {
> > > +		val = msm_readl_intr_target(pctrl, g);
> > > +		val &= ~(7 << g->intr_target_bit);
> > > +		val |= g->intr_target_kpss_val << g->intr_target_bit;
> > > +		msm_writel_intr_target(val, pctrl, g);
> > > +	}
> > >
> > >  	/* Update configuration for gpio.
> > >  	 * RAW_STATUS_EN is left on for all gpio irqs. Due to the
> > > @@ -1241,6 +1263,8 @@ int msm_pinctrl_probe(struct platform_device
> > *pdev,
> > >  	pctrl->dev = &pdev->dev;
> > >  	pctrl->soc = soc_data;
> > >  	pctrl->chip = msm_gpio_template;
> > > +	pctrl->route_to_apps = of_device_is_compatible(pctrl->dev-
> > >of_node,
> > > +					"qcom,ipq8064-pinctrl");
> > >
> > >  	raw_spin_lock_init(&pctrl->lock);
> > >
> > > @@ -1253,9 +1277,12 @@ int msm_pinctrl_probe(struct
> > platform_device *pdev,
> > >  				return PTR_ERR(pctrl->regs[i]);
> > >  		}
> > >  	} else {
> > > -		pctrl->regs[0] = devm_platform_ioremap_resource(pdev, 0);
> > > +		res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > > +		pctrl->regs[0] = devm_ioremap_resource(&pdev->dev, res);
> > >  		if (IS_ERR(pctrl->regs[0]))
> > >  			return PTR_ERR(pctrl->regs[0]);
> > > +		else
> > 
> > No need for the else, as the "positive" case is a return.
> > 
> 
> Will fix in v3
> 
> > Thank you,
> > Bjorn
> > 
> > > +			pctrl->base_reg = res->start;
> > >  	}
> > >
> > >  	msm_pinctrl_setup_pm_reset(pctrl);
> > > --
> > > 2.25.1
> > >
> 

^ permalink raw reply	[flat|nested] 4+ messages in thread

end of thread, back to index

Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-03-26 17:35 [PATCH v2] pinctrl: qcom: use scm_call to route GPIO irq to Apps Ansuel Smith
2020-03-27 20:13 ` Bjorn Andersson
2020-03-27 20:58   ` R: " ansuelsmth
2020-03-27 21:51     ` Bjorn Andersson

Linux-ARM-MSM Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-arm-msm/0 linux-arm-msm/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-arm-msm linux-arm-msm/ https://lore.kernel.org/linux-arm-msm \
		linux-arm-msm@vger.kernel.org
	public-inbox-index linux-arm-msm

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-arm-msm


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git