From: Rob Herring <robh@kernel.org>
To: Sandeep Maheswaram <sanm@codeaurora.org>
Cc: Andy Gross <agross@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Kishon Vijay Abraham I <kishon@ti.com>,
Mark Rutland <mark.rutland@arm.com>,
Stephen Boyd <swboyd@chromium.org>,
Doug Anderson <dianders@chromium.org>,
Matthias Kaehlcke <mka@chromium.org>,
linux-arm-msm@vger.kernel.org, linux-kernel@vger.kernel.org,
devicetree@vger.kernel.org, Manu Gautam <mgautam@codeaurora.org>
Subject: Re: [PATCH v7 2/4] dt-bindings: phy: qcom,qmp-usb3-dp: Add dt bindings for USB3 DP PHY
Date: Tue, 26 May 2020 15:25:07 -0600 [thread overview]
Message-ID: <20200526212507.GA391427@bogus> (raw)
In-Reply-To: <1589510358-3865-3-git-send-email-sanm@codeaurora.org>
On Fri, May 15, 2020 at 08:09:16AM +0530, Sandeep Maheswaram wrote:
> Split out the dt bindings for USB3 DP PHY from qcom,qmp bindings
> for modularity.
>
> Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
> ---
> .../devicetree/bindings/phy/qcom,qmp-phy.yaml | 51 +++-----
> .../bindings/phy/qcom,qmp-usb3-dp-phy.yaml | 135 +++++++++++++++++++++
> 2 files changed, 150 insertions(+), 36 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/phy/qcom,qmp-usb3-dp-phy.yaml
>
> diff --git a/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml
> index dcdb014..973b2d1 100644
> --- a/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml
> +++ b/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml
> @@ -27,21 +27,13 @@ properties:
> - qcom,sdm845-qhp-pcie-phy
> - qcom,sdm845-qmp-pcie-phy
> - qcom,sdm845-qmp-ufs-phy
> - - qcom,sdm845-qmp-usb3-phy
> - qcom,sdm845-qmp-usb3-uni-phy
> - qcom,sm8150-qmp-ufs-phy
> - qcom,sm8250-qmp-ufs-phy
>
> reg:
> - minItems: 1
> items:
> - description: Address and length of PHY's common serdes block.
> - - description: Address and length of the DP_COM control block.
> -
> - reg-names:
> - items:
> - - const: reg-base
> - - const: dp_com
>
> "#clock-cells":
> enum: [ 1, 2 ]
> @@ -110,7 +102,6 @@ allOf:
> compatible:
> contains:
> enum:
> - - qcom,sdm845-qmp-usb3-phy
> - qcom,sdm845-qmp-usb3-uni-phy
> then:
> properties:
> @@ -284,51 +275,39 @@ allOf:
> reset-names:
> items:
> - const: phy
> - - if:
> - properties:
> - compatible:
> - contains:
> - const: qcom,sdm845-qmp-usb3-phy
> - then:
> - required:
> - - reg-names
>
> examples:
> - |
> #include <dt-bindings/clock/qcom,gcc-sdm845.h>
> - usb_1_qmpphy: phy-wrapper@88e9000 {
> - compatible = "qcom,sdm845-qmp-usb3-phy";
> - reg = <0 0x088e9000 0 0x18c>,
> - <0 0x088e8000 0 0x10>;
> - reg-names = "reg-base", "dp_com";
> + usb_2_qmpphy: phy-wrapper@88eb000 {
> + compatible = "qcom,sdm845-qmp-usb3-uni-phy";
> + reg = <0 0x088eb000 0 0x18c>;
> #clock-cells = <1>;
> #address-cells = <2>;
> #size-cells = <2>;
>
> - clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
> + clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK >,
> <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
> - <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
> - <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
> + <&gcc GCC_USB3_SEC_CLKREF_CLK>,
> + <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
> clock-names = "aux", "cfg_ahb", "ref", "com_aux";
>
> - resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
> - <&gcc GCC_USB3_DP_PHY_PRIM_BCR>;
> + resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>,
> + <&gcc GCC_USB3_PHY_SEC_BCR>;
> reset-names = "phy", "common";
>
> vdda-phy-supply = <&vdda_usb2_ss_1p2>;
> vdda-pll-supply = <&vdda_usb2_ss_core>;
>
> - usb_1_ssphy: phy@88e9200 {
> - reg = <0 0x088e9200 0 0x128>,
> - <0 0x088e9400 0 0x200>,
> - <0 0x088e9c00 0 0x218>,
> - <0 0x088e9600 0 0x128>,
> - <0 0x088e9800 0 0x200>,
> - <0 0x088e9a00 0 0x100>;
> + usb_2_ssphy: phy@88eb200 {
> + reg = <0 0x088eb200 0 0x128>,
> + <0 0x088eb400 0 0x1fc>,
> + <0 0x088eb800 0 0x218>,
> + <0 0x088eb600 0 0x70>;
> #clock-cells = <0>;
> #phy-cells = <0>;
> - clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
> + clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
> clock-names = "pipe0";
> - clock-output-names = "usb3_phy_pipe_clk_src";
> + clock-output-names = "usb3_uni_phy_pipe_clk_src";
> };
> };
> diff --git a/Documentation/devicetree/bindings/phy/qcom,qmp-usb3-dp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,qmp-usb3-dp-phy.yaml
> new file mode 100644
> index 0000000..6055786
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/qcom,qmp-usb3-dp-phy.yaml
> @@ -0,0 +1,135 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +
> +%YAML 1.2
> +---
> +$id: "http://devicetree.org/schemas/phy/qcom,qmp-usb3-dp-phy.yaml#"
> +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
> +
> +title: Qualcomm QMP USB3 DP PHY controller
> +
> +maintainers:
> + - Manu Gautam <mgautam@codeaurora.org>
> +
> +properties:
> + compatible:
> + const:
> + qcom,sdm845-qmp-usb3-phy
> + reg:
> + items:
> + - description: Address and length of PHY's common serdes block.
> + - description: Address and length of the DP_COM control block.
> +
> + reg-names:
> + items:
> + - const: reg-base
> + - const: dp_com
> +
> + "#clock-cells":
> + enum: [ 1, 2 ]
> +
> + "#address-cells":
> + enum: [ 1, 2 ]
> +
> + "#size-cells":
> + enum: [ 1, 2 ]
> +
> + clocks:
> + items:
> + - description: Phy aux clock.
> + - description: Phy config clock.
> + - description: 19.2 MHz ref clk.
> + - description: Phy common block aux clock.
> +
> + clock-names:
> + items:
> + - const: aux
> + - const: cfg_ahb
> + - const: ref
> + - const: com_aux
> +
> + resets:
> + items:
> + - description: reset of phy block.
> + - description: phy common block reset.
> +
> + reset-names:
> + items:
> + - const: phy
> + - const: common
> +
> + vdda-phy-supply:
> + description:
> + Phandle to a regulator supply to PHY core block.
> +
> + vdda-pll-supply:
> + description:
> + Phandle to 1.8V regulator supply to PHY refclk pll block.
> +
> + vddp-ref-clk-supply:
> + description:
> + Phandle to a regulator supply to any specific refclk
> + pll block.
> +
> +#Required nodes:
> +patternProperties:
> + "^phy@[0-9a-f]+$":
> + type: object
> + description:
> + Each device node of QMP phy is required to have as many child nodes as
> + the number of lanes the PHY has.
Probably not a new problem, but where are the child node properties
documented? They need to be added before you duplicate this problem.
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - "#clock-cells"
> + - "#address-cells"
> + - "#size-cells"
> + - clocks
> + - clock-names
> + - resets
> + - reset-names
> + - vdda-phy-supply
> + - vdda-pll-supply
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/clock/qcom,gcc-sdm845.h>
> + usb_1_qmpphy: phy-wrapper@88e9000 {
> + compatible = "qcom,sdm845-qmp-usb3-phy";
> + reg = <0 0x088e9000 0 0x18c>,
> + <0 0x088e8000 0 0x10>;
> + reg-names = "reg-base", "dp_com";
> + #clock-cells = <1>;
> + #address-cells = <2>;
> + #size-cells = <2>;
You're missing 'ranges', so the child addresses are not translatable.
You could also reduce everything to 1 cell as they are contained within
the parent's range.
> +
> + clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
> + <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
> + <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
> + <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
> + clock-names = "aux", "cfg_ahb", "ref", "com_aux";
> +
> + resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
> + <&gcc GCC_USB3_DP_PHY_PRIM_BCR>;
> + reset-names = "phy", "common";
> +
> + vdda-phy-supply = <&vdda_usb2_ss_1p2>;
> + vdda-pll-supply = <&vdda_usb2_ss_core>;
> +
> + usb_1_ssphy: phy@88e9200 {
> + reg = <0 0x088e9200 0 0x128>,
> + <0 0x088e9400 0 0x200>,
> + <0 0x088e9c00 0 0x218>,
> + <0 0x088e9600 0 0x128>,
> + <0 0x088e9800 0 0x200>,
> + <0 0x088e9a00 0 0x100>;
> + #clock-cells = <0>;
> + #phy-cells = <0>;
> + clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
> + clock-names = "pipe0";
> + clock-output-names = "usb3_phy_pipe_clk_src";
> + };
> + };
> --
> QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
> of Code Aurora Forum, hosted by The Linux Foundation
>
next prev parent reply other threads:[~2020-05-26 21:25 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-05-15 2:39 [PATCH v7 0/4] Add QMP V3 USB3 PHY support for SC7180 Sandeep Maheswaram
2020-05-15 2:39 ` [PATCH v7 1/4] dt-bindings: phy: qcom,qmp: Convert QMP PHY bindings to yaml Sandeep Maheswaram
2020-05-15 18:18 ` Matthias Kaehlcke
2020-05-15 2:39 ` [PATCH v7 2/4] dt-bindings: phy: qcom,qmp-usb3-dp: Add dt bindings for USB3 DP PHY Sandeep Maheswaram
2020-05-15 18:39 ` Matthias Kaehlcke
2020-05-26 21:25 ` Rob Herring [this message]
2020-05-15 2:39 ` [PATCH v7 3/4] dt-bindings: phy: qcom,qmp-usb3-dp: Add support for SC7180 Sandeep Maheswaram
2020-05-26 21:25 ` Rob Herring
2020-05-15 2:39 ` [PATCH v7 4/4] phy: qcom-qmp: Add QMP V3 USB3 PHY " Sandeep Maheswaram
2020-05-19 6:23 ` [PATCH v7 0/4] " Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200526212507.GA391427@bogus \
--to=robh@kernel.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=dianders@chromium.org \
--cc=kishon@ti.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mgautam@codeaurora.org \
--cc=mka@chromium.org \
--cc=sanm@codeaurora.org \
--cc=swboyd@chromium.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).