From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Jonathan Marek <jonathan@marek.ca>
Cc: linux-arm-msm@vger.kernel.org, Andy Gross <agross@kernel.org>,
Kishon Vijay Abraham I <kishon@ti.com>,
Vinod Koul <vkoul@kernel.org>,
"open list:GENERIC PHY FRAMEWORK" <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH 2/3] phy: qcom-qmp: Add QMP V4 USB3 UNIPHY
Date: Fri, 26 Jun 2020 00:37:09 -0700 [thread overview]
Message-ID: <20200626073709.GF388985@builder.lan> (raw)
In-Reply-To: <20200524021416.17049-3-jonathan@marek.ca>
On Sat 23 May 19:14 PDT 2020, Jonathan Marek wrote:
> Add support for the USB3 PHY used by the secondary usb controller on sm8150
>
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
I've not reviewed the individual register listings, but the rest looks
good.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Regards,
Bjorn
> ---
> drivers/phy/qualcomm/phy-qcom-qmp.c | 150 ++++++++++++++++++++++++++++
> drivers/phy/qualcomm/phy-qcom-qmp.h | 5 +
> 2 files changed, 155 insertions(+)
>
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
> index b3e07afca3ca..9367f8f793b5 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
> @@ -199,6 +199,17 @@ static const unsigned int qmp_v4_usb3phy_regs_layout[QPHY_LAYOUT_SIZE] = {
> [QPHY_START_CTRL] = 0x44,
> [QPHY_PCS_STATUS] = 0x14,
> [QPHY_PCS_POWER_DOWN_CONTROL] = 0x40,
> + [QPHY_PCS_AUTONOMOUS_MODE_CTRL] = 0x308,
> + [QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR] = 0x314,
> +};
> +
> +static const unsigned int qmp_v4_usb3_uniphy_regs_layout[QPHY_LAYOUT_SIZE] = {
> + [QPHY_SW_RESET] = 0x00,
> + [QPHY_START_CTRL] = 0x44,
> + [QPHY_PCS_STATUS] = 0x14,
> + [QPHY_PCS_POWER_DOWN_CONTROL] = 0x40,
> + [QPHY_PCS_AUTONOMOUS_MODE_CTRL] = 0x608,
> + [QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR] = 0x614,
> };
>
> static const unsigned int sdm845_ufsphy_regs_layout[QPHY_LAYOUT_SIZE] = {
> @@ -1413,6 +1424,114 @@ static const struct qmp_phy_init_tbl sm8150_usb3_pcs_tbl[] = {
> QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_RXEQTRAINING_DFE_TIME_S2, 0x07),
> };
>
> +static const struct qmp_phy_init_tbl sm8150_usb3_uniphy_serdes_tbl[] = {
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_SYSCLK_EN_SEL, 0x1a),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_HSCLK_SEL, 0x11),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_HSCLK_SEL, 0x01),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_DEC_START_MODE0, 0x82),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START1_MODE0, 0xab),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START2_MODE0, 0xea),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START3_MODE0, 0x02),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE1_MODE0, 0xca),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE2_MODE0, 0x1e),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_CP_CTRL_MODE0, 0x06),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_RCTRL_MODE0, 0x16),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_CCTRL_MODE0, 0x36),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE1_MODE0, 0x24),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP2_MODE0, 0x34),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP1_MODE0, 0x14),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP_EN, 0x04),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_SYSCLK_BUF_ENABLE, 0x0a),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE2_MODE1, 0x02),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE1_MODE1, 0x24),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_CORECLK_DIV_MODE1, 0x08),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_DEC_START_MODE1, 0x82),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START1_MODE1, 0xab),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START2_MODE1, 0xea),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START3_MODE1, 0x02),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP2_MODE1, 0x82),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP1_MODE1, 0x34),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_CP_CTRL_MODE1, 0x06),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_RCTRL_MODE1, 0x16),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_CCTRL_MODE1, 0x36),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE1_MODE1, 0xca),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE2_MODE1, 0x1e),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_CMN_IPTRIM, 0x20),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_EN_CENTER, 0x01),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_PER1, 0x31),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_PER2, 0x01),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE1_MODE1, 0xde),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE2_MODE1, 0x07),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE1_MODE0, 0xde),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE2_MODE0, 0x07),
> + QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE_MAP, 0x02),
> +};
> +
> +static const struct qmp_phy_init_tbl sm8150_usb3_uniphy_tx_tbl[] = {
> + QMP_PHY_INIT_CFG(QSERDES_V4_TX_RCV_DETECT_LVL_2, 0x12),
> + QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_1, 0x95),
> + QMP_PHY_INIT_CFG(QSERDES_V4_TX_PI_QEC_CTRL, 0x40),
> + QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_TX, 0x05),
> +};
> +
> +static const struct qmp_phy_init_tbl sm8150_usb3_uniphy_rx_tbl[] = {
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0xb8),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH3, 0x7f),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH2, 0x37),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH, 0x2f),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_LOW, 0xef),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0xb3),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x0b),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0x5c),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0xdc),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0xdc),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0x99),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH1, 0x04),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH2, 0x08),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN1, 0x05),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN2, 0x05),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN, 0x2f),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW, 0xff),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_HIGH, 0x0f),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x7f),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FO_GAIN, 0x08),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL1, 0x54),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL2, 0x0c),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_GM_CAL, 0x1f),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4a),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x0a),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_EN_TIMER, 0x04),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x47),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x04),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x0e),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x00),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0xc0),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_CTLE_POST_CAL_OFFSET, 0x20),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x04),
> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_DCC_CTRL1, 0x0c),
> +};
> +
> +static const struct qmp_phy_init_tbl sm8150_usb3_uniphy_pcs_tbl[] = {
> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG1, 0xd0),
> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG2, 0x07),
> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG3, 0x20),
> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG6, 0x13),
> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_L, 0xe7),
> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_H, 0x03),
> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_RX_SIGDET_LVL, 0xaa),
> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_UNI_RXEQTRAINING_DFE_TIME_S2, 0x07),
> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_UNI_LFPS_DET_HIGH_COUNT_VAL, 0xf8),
> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_CDR_RESET_TIME, 0x0f),
> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG1, 0x88),
> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG2, 0x13),
> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG1, 0x4b),
> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG5, 0x10),
> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_REFGEN_REQ_CONFIG1, 0x21),
> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCS_TX_RX_CONFIG, 0x0c),
> +};
> +
> /* struct qmp_phy_cfg - per-PHY initialization config */
> struct qmp_phy_cfg {
> /* phy-type - PCIE/UFS/USB */
> @@ -2000,6 +2119,34 @@ static const struct qmp_phy_cfg sm8150_usb3phy_cfg = {
> .is_dual_lane_phy = true,
> };
>
> +static const struct qmp_phy_cfg sm8150_usb3_uniphy_cfg = {
> + .type = PHY_TYPE_USB3,
> + .nlanes = 1,
> +
> + .serdes_tbl = sm8150_usb3_uniphy_serdes_tbl,
> + .serdes_tbl_num = ARRAY_SIZE(sm8150_usb3_uniphy_serdes_tbl),
> + .tx_tbl = sm8150_usb3_uniphy_tx_tbl,
> + .tx_tbl_num = ARRAY_SIZE(sm8150_usb3_uniphy_tx_tbl),
> + .rx_tbl = sm8150_usb3_uniphy_rx_tbl,
> + .rx_tbl_num = ARRAY_SIZE(sm8150_usb3_uniphy_rx_tbl),
> + .pcs_tbl = sm8150_usb3_uniphy_pcs_tbl,
> + .pcs_tbl_num = ARRAY_SIZE(sm8150_usb3_uniphy_pcs_tbl),
> + .clk_list = qmp_v4_phy_clk_l,
> + .num_clks = ARRAY_SIZE(qmp_v4_phy_clk_l),
> + .reset_list = msm8996_usb3phy_reset_l,
> + .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l),
> + .vreg_list = qmp_phy_vreg_l,
> + .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l),
> + .regs = qmp_v4_usb3_uniphy_regs_layout,
> +
> + .start_ctrl = SERDES_START | PCS_START,
> + .pwrdn_ctrl = SW_PWRDN,
> +
> + .has_pwrdn_delay = true,
> + .pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN,
> + .pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
> +};
> +
> static void qcom_qmp_phy_configure_lane(void __iomem *base,
> const unsigned int *regs,
> const struct qmp_phy_init_tbl tbl[],
> @@ -2774,6 +2921,9 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
> }, {
> .compatible = "qcom,sm8150-qmp-usb3-phy",
> .data = &sm8150_usb3phy_cfg,
> + }, {
> + .compatible = "qcom,sm8150-qmp-usb3-uni-phy",
> + .data = &sm8150_usb3_uniphy_cfg,
> },
> { },
> };
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
> index 6d017a0c0c8d..f39f7a968228 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp.h
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
> @@ -363,6 +363,7 @@
> /* Only for QMP V4 PHY - TX registers */
> #define QSERDES_V4_TX_RES_CODE_LANE_TX 0x34
> #define QSERDES_V4_TX_RES_CODE_LANE_RX 0x38
> +#define QSERDES_V4_TX_RES_CODE_LANE_OFFSET_TX 0x3c
> #define QSERDES_V4_TX_LANE_MODE_1 0x84
> #define QSERDES_V4_TX_RCV_DETECT_LVL_2 0x9c
> #define QSERDES_V4_TX_PWM_GEAR_1_DIVIDER_BAND0_1 0xd8
> @@ -709,6 +710,10 @@
> #define QPHY_V4_PCS_USB3_SIGDET_STARTUP_TIMER_VAL 0x354
> #define QPHY_V4_PCS_USB3_TEST_CONTROL 0x358
>
> +/* Only for QMP V4 PHY - UNI has 0x300 offset for PCS_USB3 regs */
> +#define QPHY_V4_PCS_USB3_UNI_LFPS_DET_HIGH_COUNT_VAL 0x618
> +#define QPHY_V4_PCS_USB3_UNI_RXEQTRAINING_DFE_TIME_S2 0x638
> +
> /* Only for QMP V4 PHY - PCS_MISC registers */
> #define QPHY_V4_PCS_MISC_TYPEC_CTRL 0x00
> #define QPHY_V4_PCS_MISC_TYPEC_PWRDN_CTRL 0x04
> --
> 2.26.1
>
next prev parent reply other threads:[~2020-06-26 7:39 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-05-24 2:14 [PATCH 0/3] phy: qcom-qmp: add V4 USB PHYs Jonathan Marek
2020-05-24 2:14 ` [PATCH 1/3] phy: qcom-qmp: Allow different values for second lane Jonathan Marek
2020-06-25 19:41 ` Dmitry Baryshkov
2020-06-26 7:35 ` Bjorn Andersson
2020-05-24 2:14 ` [PATCH 2/3] phy: qcom-qmp: Add QMP V4 USB3 UNIPHY Jonathan Marek
2020-06-25 19:42 ` Dmitry Baryshkov
2020-06-26 7:37 ` Bjorn Andersson [this message]
2020-05-24 2:14 ` [PATCH 3/3] phy: qcom-qmp: Add QMP V4 USB3 PHY support for sm8250 Jonathan Marek
2020-06-25 19:42 ` Dmitry Baryshkov
2020-06-26 7:40 ` Bjorn Andersson
2020-06-29 9:41 ` [PATCH 0/3] phy: qcom-qmp: add V4 USB PHYs Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200626073709.GF388985@builder.lan \
--to=bjorn.andersson@linaro.org \
--cc=agross@kernel.org \
--cc=jonathan@marek.ca \
--cc=kishon@ti.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).