From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Loic Poulain <loic.poulain@linaro.org>
Cc: manivannan.sadhasivam@linaro.org, hemantk@codeaurora.org,
linux-arm-msm@vger.kernel.org
Subject: Re: [PATCH] bus: mhi: Add MHI PCI support
Date: Wed, 23 Sep 2020 10:17:09 -0500 [thread overview]
Message-ID: <20200923151709.GC40811@yoga> (raw)
In-Reply-To: <1600868432-12438-1-git-send-email-loic.poulain@linaro.org>
On Wed 23 Sep 08:40 CDT 2020, Loic Poulain wrote:
> This is a generic MHI-over-PCI controller driver for MHI only devices
> such as QCOM modems. For now it supports registering of Qualcomm SDX55
> based PCIe modules. The MHI channels have been extracted from mhi
> downstream driver.
>
> This driver is easily extendable to support other MHI PCI devices like
> different modem hw or OEM superset.
>
> Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
> ---
[..]
> diff --git a/drivers/bus/mhi/controllers/mhi_pci_common.c b/drivers/bus/mhi/controllers/mhi_pci_common.c
> new file mode 100644
> index 0000000..705b283
> --- /dev/null
> +++ b/drivers/bus/mhi/controllers/mhi_pci_common.c
ath11k is also "PCI" and "MHI" but this isn't "common" code for it, so
perhaps "mhi_pci_generic.c" or "mhi_pci_modem.c"?
> @@ -0,0 +1,339 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * MHI PCI driver - MHI over PCI controller driver
> + *
> + * This module is a generic driver for registering pure MHI-over-PCI devices,
> + * such as PCIe QCOM modems.
> + *
> + * Copyright (C) 2020 Linaro Ltd <loic.poulain@linaro.org>
> + */
> +
> +#include <linux/device.h>
> +#include <linux/mhi.h>
> +#include <linux/module.h>
> +#include <linux/pci.h>
> +#include <linux/delay.h>
Can you confirm that you need delay.h?
> +
> +#define MHI_PCI_BAR_NUM 0
> +
> +enum {
> + EV_RING_0,
> + EV_RING_1,
> + EV_RING_2,
> + EV_RING_3,
Maybe you can just use the numbers 0-3 instead?
> +};
> +
[..]
> +static int mhi_pci_claim(struct mhi_controller *mhic)
> +{
> + struct pci_dev *pdev = to_pci_dev(mhic->cntrl_dev);
> + int err;
> +
> + err = pci_assign_resource(pdev, MHI_PCI_BAR_NUM);
> + if (err) {
> + dev_err(&pdev->dev, "failed to assign pci resource: %d\n", err);
Afaict all code paths of pci_assign_resource() will log already.
> + return err;
> + }
> +
> + err = pcim_enable_device(pdev);
> + if (err) {
> + dev_err(&pdev->dev, "failed to enable pci device: %d\n", err);
> + return err;
> + }
> +
> + err = pcim_iomap_regions(pdev, 1 << MHI_PCI_BAR_NUM, pci_name(pdev));
> + if (err) {
> + dev_err(&pdev->dev, "failed to map pci region: %d\n", err);
> + return err;
> + }
> + mhic->regs = pcim_iomap_table(pdev)[MHI_PCI_BAR_NUM];
> +
> + err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
> + if (err) {
> + dev_err(&pdev->dev, "Cannot set proper DMA mask\n");
> + return err;
> + }
> +
> + err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
> + if (err) {
> + dev_err(&pdev->dev, "set consistent dma mask failed\n");
> + return err;
> + }
> +
> + pci_set_master(pdev);
> +
> + return 0;
> +}
[..]
> +static int mhi_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
> +{
> + const struct mhi_pci_dev_info *info = (struct mhi_pci_dev_info *) id->driver_data;
> + const struct mhi_controller_config *mhic_config;
> + struct mhi_controller *mhic;
> + int err;
> +
> + dev_info(&pdev->dev, "MHI PCI device found: %s\n", info->name);
> +
> + mhic = devm_kzalloc(&pdev->dev, sizeof(*mhic), GFP_KERNEL);
> + if (!mhic) {
> + dev_err(&pdev->dev, "failed to allocate mhi controller\n");
kzalloc() will log errors as well.
> + return -ENOMEM;
> + }
> +
> + mhic_config = info->config;
> + mhic->cntrl_dev = &pdev->dev;
> + mhic->iova_start = 0;
> + mhic->iova_stop = 0xffffffff;
> + mhic->fw_image = NULL;
> + mhic->edl_image = NULL;
> +
> + mhic->read_reg = mhi_pci_read_reg;
> + mhic->write_reg = mhi_pci_write_reg;
> + mhic->status_cb = mhi_pci_status_cb;
> + mhic->runtime_get = mhi_pci_runtime_get;
> + mhic->runtime_put = mhi_pci_runtime_put;
> +
> + err = mhi_pci_claim(mhic);
> + if (err)
> + return err;
> +
> + err = mhi_pci_get_irqs(mhic, mhic_config);
> + if (err)
> + return err;
> +
> + pci_set_drvdata(pdev, mhic);
> +
> + err = mhi_register_controller(mhic, mhic_config);
> + if (err) {
> + dev_err(&pdev->dev, "failed to register MHI controller\n");
Afaict all errors that occurs if you pass valid data to this function
will print an error message already...
> + pci_free_irq_vectors(pdev);
> + return err;
> + }
> +
> + /* MHI bus does not power up the controller by default */
> + err = mhi_prepare_for_power_up(mhic);
> + if (err) {
> + dev_err(&pdev->dev, "failed to prepare MHI controller\n");
mhi_unregister_controller()?
> + return err;
> + }
> +
> + err = mhi_sync_power_up(mhic);
> + if (err) {
> + dev_err(&pdev->dev, "failed to power up MHI controller\n");
> + mhi_unprepare_after_power_down(mhic);
> + mhi_unregister_controller(mhic);
> + return err;
> + }
> +
> + return 0;
> +}
> +
> +static void mhi_pci_remove(struct pci_dev *pdev)
> +{
> + struct mhi_controller *mhic = pci_get_drvdata(pdev);
> +
> + mhi_power_down(mhic, true);
> + mhi_unprepare_after_power_down(mhic);
> + mhi_unregister_controller(mhic);
> +}
> +
> +static struct pci_driver mhi_pci_driver = {
> + .name = "mhi-pci",
> + .id_table = mhi_pci_id_table,
> + .probe = mhi_pci_probe,
> + .remove = mhi_pci_remove
> +};
> +module_pci_driver(mhi_pci_driver);
> +
> +MODULE_AUTHOR("Loic Poulain <loic.poulain@linaro,org>");
> +MODULE_DESCRIPTION("mhi-pci");
Please expand this
> +MODULE_LICENSE("GPL");
> +MODULE_VERSION("1");
And please drop the version, as this is likely not going to be updated
consistently.
Regards,
Bjorn
next prev parent reply other threads:[~2020-09-23 15:17 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-09-23 13:40 [PATCH] bus: mhi: Add MHI PCI support Loic Poulain
2020-09-23 14:03 ` Jeffrey Hugo
2020-09-23 14:35 ` Loic Poulain
2020-09-23 14:55 ` Jeffrey Hugo
2020-09-23 15:42 ` Loic Poulain
2020-09-23 15:17 ` Bjorn Andersson [this message]
2020-09-23 15:28 ` Jeffrey Hugo
2020-09-23 16:31 ` Loic Poulain
2020-09-26 5:18 ` Manivannan Sadhasivam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200923151709.GC40811@yoga \
--to=bjorn.andersson@linaro.org \
--cc=hemantk@codeaurora.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=loic.poulain@linaro.org \
--cc=manivannan.sadhasivam@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).