From: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
To: miquel.raynal@bootlin.com, richard@nod.at, vigneshr@ti.com,
robh+dt@kernel.org
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-mtd@lists.infradead.org, linux-kernel@vger.kernel.org,
boris.brezillon@collabora.com, Daniele.Palmas@telit.com,
bjorn.andersson@linaro.org,
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>,
Rob Herring <robh@kernel.org>
Subject: [PATCH v4 1/3] dt-bindings: mtd: Convert Qcom NANDc binding to YAML
Date: Mon, 8 Mar 2021 11:14:45 +0530 [thread overview]
Message-ID: <20210308054447.28418-2-manivannan.sadhasivam@linaro.org> (raw)
In-Reply-To: <20210308054447.28418-1-manivannan.sadhasivam@linaro.org>
Convert Qcom NANDc devicetree binding to YAML.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../devicetree/bindings/mtd/qcom,nandc.yaml | 196 ++++++++++++++++++
.../devicetree/bindings/mtd/qcom_nandc.txt | 142 -------------
2 files changed, 196 insertions(+), 142 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mtd/qcom,nandc.yaml
delete mode 100644 Documentation/devicetree/bindings/mtd/qcom_nandc.txt
diff --git a/Documentation/devicetree/bindings/mtd/qcom,nandc.yaml b/Documentation/devicetree/bindings/mtd/qcom,nandc.yaml
new file mode 100644
index 000000000000..84ad7ff30121
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/qcom,nandc.yaml
@@ -0,0 +1,196 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/qcom,nandc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm NAND controller
+
+maintainers:
+ - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+
+properties:
+ compatible:
+ enum:
+ - qcom,ipq806x-nand
+ - qcom,ipq4019-nand
+ - qcom,ipq6018-nand
+ - qcom,ipq8074-nand
+ - qcom,sdx55-nand
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: Core Clock
+ - description: Always ON Clock
+
+ clock-names:
+ items:
+ - const: core
+ - const: aon
+
+ "#address-cells": true
+ "#size-cells": true
+
+patternProperties:
+ "^nand@[a-f0-9]$":
+ type: object
+ properties:
+ nand-bus-width:
+ const: 8
+
+ nand-ecc-strength:
+ enum: [1, 4, 8]
+
+ nand-ecc-step-size:
+ enum:
+ - 512
+
+allOf:
+ - $ref: "nand-controller.yaml#"
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: qcom,ipq806x-nand
+ then:
+ properties:
+ dmas:
+ items:
+ - description: rxtx DMA channel
+
+ dma-names:
+ items:
+ - const: rxtx
+
+ qcom,cmd-crci:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Must contain the ADM command type CRCI block instance number
+ specified for the NAND controller on the given platform
+
+ qcom,data-crci:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Must contain the ADM data type CRCI block instance number
+ specified for the NAND controller on the given platform
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - qcom,ipq4019-nand
+ - qcom,ipq6018-nand
+ - qcom,ipq8074-nand
+ - qcom,sdx55-nand
+
+ then:
+ properties:
+ dmas:
+ items:
+ - description: tx DMA channel
+ - description: rx DMA channel
+ - description: cmd DMA channel
+
+ dma-names:
+ items:
+ - const: tx
+ - const: rx
+ - const: cmd
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,gcc-ipq806x.h>
+ nand-controller@1ac00000 {
+ compatible = "qcom,ipq806x-nand";
+ reg = <0x1ac00000 0x800>;
+
+ clocks = <&gcc EBI2_CLK>,
+ <&gcc EBI2_AON_CLK>;
+ clock-names = "core", "aon";
+
+ dmas = <&adm_dma 3>;
+ dma-names = "rxtx";
+ qcom,cmd-crci = <15>;
+ qcom,data-crci = <3>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ nand@0 {
+ reg = <0>;
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "boot-nand";
+ reg = <0 0x58a0000>;
+ };
+
+ partition@58a0000 {
+ label = "fs-nand";
+ reg = <0x58a0000 0x4000000>;
+ };
+ };
+ };
+ };
+
+ #include <dt-bindings/clock/qcom,gcc-ipq4019.h>
+ nand-controller@79b0000 {
+ compatible = "qcom,ipq4019-nand";
+ reg = <0x79b0000 0x1000>;
+
+ clocks = <&gcc GCC_QPIC_CLK>,
+ <&gcc GCC_QPIC_AHB_CLK>;
+ clock-names = "core", "aon";
+
+ dmas = <&qpicbam 0>,
+ <&qpicbam 1>,
+ <&qpicbam 2>;
+ dma-names = "tx", "rx", "cmd";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ nand@0 {
+ reg = <0>;
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "boot-nand";
+ reg = <0 0x58a0000>;
+ };
+
+ partition@58a0000 {
+ label = "fs-nand";
+ reg = <0x58a0000 0x4000000>;
+ };
+ };
+ };
+ };
+
+...
diff --git a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
deleted file mode 100644
index 5647913d8837..000000000000
--- a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
+++ /dev/null
@@ -1,142 +0,0 @@
-* Qualcomm NAND controller
-
-Required properties:
-- compatible: must be one of the following:
- * "qcom,ipq806x-nand" - for EBI2 NAND controller being used in IPQ806x
- SoC and it uses ADM DMA
- * "qcom,ipq4019-nand" - for QPIC NAND controller v1.4.0 being used in
- IPQ4019 SoC and it uses BAM DMA
- * "qcom,ipq6018-nand" - for QPIC NAND controller v1.5.0 being used in
- IPQ6018 SoC and it uses BAM DMA
- * "qcom,ipq8074-nand" - for QPIC NAND controller v1.5.0 being used in
- IPQ8074 SoC and it uses BAM DMA
- * "qcom,sdx55-nand" - for QPIC NAND controller v2.0.0 being used in
- SDX55 SoC and it uses BAM DMA
-
-- reg: MMIO address range
-- clocks: must contain core clock and always on clock
-- clock-names: must contain "core" for the core clock and "aon" for the
- always on clock
-
-EBI2 specific properties:
-- dmas: DMA specifier, consisting of a phandle to the ADM DMA
- controller node and the channel number to be used for
- NAND. Refer to dma.txt and qcom_adm.txt for more details
-- dma-names: must be "rxtx"
-- qcom,cmd-crci: must contain the ADM command type CRCI block instance
- number specified for the NAND controller on the given
- platform
-- qcom,data-crci: must contain the ADM data type CRCI block instance
- number specified for the NAND controller on the given
- platform
-
-QPIC specific properties:
-- dmas: DMA specifier, consisting of a phandle to the BAM DMA
- and the channel number to be used for NAND. Refer to
- dma.txt, qcom_bam_dma.txt for more details
-- dma-names: must contain all 3 channel names : "tx", "rx", "cmd"
-- #address-cells: <1> - subnodes give the chip-select number
-- #size-cells: <0>
-
-* NAND chip-select
-
-Each controller may contain one or more subnodes to represent enabled
-chip-selects which (may) contain NAND flash chips. Their properties are as
-follows.
-
-Required properties:
-- reg: a single integer representing the chip-select
- number (e.g., 0, 1, 2, etc.)
-- #address-cells: see partition.txt
-- #size-cells: see partition.txt
-
-Optional properties:
-- nand-bus-width: see nand-controller.yaml
-- nand-ecc-strength: see nand-controller.yaml. If not specified, then ECC strength will
- be used according to chip requirement and available
- OOB size.
-
-Each nandcs device node may optionally contain a 'partitions' sub-node, which
-further contains sub-nodes describing the flash partition mapping. See
-partition.txt for more detail.
-
-Example:
-
-nand-controller@1ac00000 {
- compatible = "qcom,ipq806x-nand";
- reg = <0x1ac00000 0x800>;
-
- clocks = <&gcc EBI2_CLK>,
- <&gcc EBI2_AON_CLK>;
- clock-names = "core", "aon";
-
- dmas = <&adm_dma 3>;
- dma-names = "rxtx";
- qcom,cmd-crci = <15>;
- qcom,data-crci = <3>;
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- nand@0 {
- reg = <0>;
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "boot-nand";
- reg = <0 0x58a0000>;
- };
-
- partition@58a0000 {
- label = "fs-nand";
- reg = <0x58a0000 0x4000000>;
- };
- };
- };
-};
-
-nand-controller@79b0000 {
- compatible = "qcom,ipq4019-nand";
- reg = <0x79b0000 0x1000>;
-
- clocks = <&gcc GCC_QPIC_CLK>,
- <&gcc GCC_QPIC_AHB_CLK>;
- clock-names = "core", "aon";
-
- dmas = <&qpicbam 0>,
- <&qpicbam 1>,
- <&qpicbam 2>;
- dma-names = "tx", "rx", "cmd";
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- nand@0 {
- reg = <0>;
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "boot-nand";
- reg = <0 0x58a0000>;
- };
-
- partition@58a0000 {
- label = "fs-nand";
- reg = <0x58a0000 0x4000000>;
- };
- };
- };
-};
--
2.25.1
next prev parent reply other threads:[~2021-03-08 5:46 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-03-08 5:44 [PATCH v4 0/3] Add support for secure regions in Qcom NANDc driver Manivannan Sadhasivam
2021-03-08 5:44 ` Manivannan Sadhasivam [this message]
2021-03-08 5:44 ` [PATCH v4 2/3] dt-bindings: mtd: Add a property to declare secure regions in NAND chips Manivannan Sadhasivam
2021-03-08 9:10 ` Boris Brezillon
2021-03-08 13:31 ` Manivannan Sadhasivam
2021-03-09 7:57 ` Boris Brezillon
2021-03-08 5:44 ` [PATCH v4 3/3] mtd: rawnand: qcom: Add support for secure regions in NAND memory Manivannan Sadhasivam
2021-03-08 9:02 ` Boris Brezillon
2021-03-08 13:34 ` Manivannan Sadhasivam
2021-03-08 13:34 ` Manivannan Sadhasivam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210308054447.28418-2-manivannan.sadhasivam@linaro.org \
--to=manivannan.sadhasivam@linaro.org \
--cc=Daniele.Palmas@telit.com \
--cc=bjorn.andersson@linaro.org \
--cc=boris.brezillon@collabora.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=miquel.raynal@bootlin.com \
--cc=richard@nod.at \
--cc=robh+dt@kernel.org \
--cc=robh@kernel.org \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).