linux-arm-msm.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Marijn Suijten <marijn.suijten@somainline.org>
Cc: Pavel Machek <pavel@ucw.cz>, Dan Murphy <dmurphy@ti.com>,
	Rob Herring <robh+dt@kernel.org>, Andy Gross <agross@kernel.org>,
	Thierry Reding <thierry.reding@gmail.com>,
	Uwe Kleine-K?nig <u.kleine-koenig@pengutronix.de>,
	Lee Jones <lee.jones@linaro.org>,
	Martin Botka <martin.botka1@gmail.com>,
	linux-leds@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org,
	linux-pwm@vger.kernel.org
Subject: Re: [PATCH v6 2/4] leds: Add driver for Qualcomm LPG
Date: Wed, 28 Apr 2021 17:39:39 -0500	[thread overview]
Message-ID: <20210428223939.GN1908499@yoga> (raw)
In-Reply-To: <881fb5a3-fb51-3967-63de-a09950839855@somainline.org>

On Sun 18 Apr 16:54 CDT 2021, Marijn Suijten wrote:

> Hi Bjorn,
> 
> On 10/21/20 10:12 PM, Bjorn Andersson wrote:
> > The Light Pulse Generator (LPG) is a PWM-block found in a wide range of
> > PMICs from Qualcomm. It can operate on fixed parameters or based on a
> > lookup-table, altering the duty cycle over time - which provides the
> > means for e.g. hardware assisted transitions of LED brightness.
> > 
> > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> > Tested-by: Luca Weiss <luca@z3ntu.xyz>
> 
> 
> Thanks for these patches.  I have tested them successfully on the Sony
> Xperia XA2 (Discovery, Nile platform) with the leds on the PM660l - feel
> free to add my Tested-by.  Should I send the configuration your way for
> inclusion in this patch, or submit them separately (either applied after, or
> included as separate patches in the next version of this series)?
> 

Thanks for testing, let's try to land this first iteration first and
then we can add PM660l and PM8150* definitions/support on top.

> > +/**
> > + * struct lpg_data - initialization data
> > + * @lut_base:		base address of LUT block
> > + * @lut_size:		number of entries in LUT
> > + * @triled_base:	base address of TRILED
> > + * @pwm_9bit_mask:	bitmask for switching from 6bit to 9bit pwm
> 
> 
> Our downstream kernel derives this from the "LPG subtype" for each distinct
> channel, read from register offset +0x5.  A value of 0xb is subtype "PWM"
> with a shift of 2, a value of 0x11 is subtype "LPG_LITE" with a shift of 4.
> Can we do the same here instead of hardcoding it for all channels in the LPG
> at once?  How should we determine if the mask is one or two bits wide, for
> the 3<<4 case?
> 

I don't see any obvious solution to the latter, so perhaps we should
just stick with defining this per compatible? Or am I reading your
suggestion wrong?

> > + * @num_channels:	number of channels in LPG
> > + * @channels:		list of channel initialization data
> > + */
> 
> > +	if (ping_pong) {
> > +		if (len % 2)
> > +			hi_pause = 0;
> > +		else
> > +			hi_pause = pattern[len + 1 / 2].delta_t;
> 
> 
> len + 1 should be wrapped in parentheses just like the reassignment to len=
> below, otherwise this is always an out of bounds read (at len + 0).
> 

Thanks for spotting this.

> > +		lo_pause = pattern[len - 1].delta_t;
> > +
> > +		len = (len + 1) / 2;
> > +	} else {
> > +		hi_pause = pattern[len - 1].delta_t;
> > +		lo_pause = 0;
> > +	}
> > +
> > +	ret = lpg_lut_store(lpg, pattern, len, &lo_idx, &hi_idx);
> > +	if (ret < 0)
> > +		goto out;
> > +
> > +	for (i = 0; i < led->num_channels; i++) {
> > +		chan = led->channels[i];
> > +
> > +		chan->ramp_duration_ms = pattern[0].delta_t * len;
> 
> 
> Perhaps this could store the duration of a single step instead, since the
> only use in lpg_apply_lut_control divides it by pattern length again?
> 

Sounds like a good idea.

> > +		chan->ramp_ping_pong = ping_pong;
> > +		chan->ramp_oneshot = repeat != -1;
> > +
> > +		chan->ramp_lo_pause_ms = lo_pause;
> > +		chan->ramp_hi_pause_ms = hi_pause;
> > +
> > +		chan->pattern_lo_idx = lo_idx;
> > +		chan->pattern_hi_idx = hi_idx;
> > +	}
> > +
> > +out:
> > +	return ret;
> > +}
> 
> > +static int lpg_init_lut(struct lpg *lpg)
> > +{
> > +	const struct lpg_data *data = lpg->data;
> > +	size_t bitmap_size;
> > +
> > +	if (!data->lut_base)
> > +		return 0;
> > +
> > +	lpg->lut_base = data->lut_base;
> > +	lpg->lut_size = data->lut_size;
> > +
> > +	bitmap_size = BITS_TO_LONGS(lpg->lut_size) * sizeof(unsigned long);
> > +	lpg->lut_bitmap = devm_kzalloc(lpg->dev, bitmap_size, GFP_KERNEL);
> 
> 
> Would it be nicer to use BITS_TO_BYTES here, or otherwise devm_kcalloc(...,
> bitmap_size, sizeof(long), ...) without mutiplying with sizeof(unsigned
> long)?
> 

Yes, that's cleaner.

> > +
> > +	bitmap_clear(lpg->lut_bitmap, 0, lpg->lut_size);
> > +	return lpg->lut_bitmap ? 0 : -ENOMEM;
> > +}
> > +
> > +static int lpg_probe(struct platform_device *pdev)
> > +{
> > +	struct device_node *np;
> > +	struct lpg *lpg;
> > +	int ret;
> > +	int i;
> > +
> > +	lpg = devm_kzalloc(&pdev->dev, sizeof(*lpg), GFP_KERNEL);
> > +	if (!lpg)
> > +		return -ENOMEM;
> > +
> > +	lpg->data = of_device_get_match_data(&pdev->dev);
> > +	if (!lpg->data)
> > +		return -EINVAL;
> > +
> > +	lpg->dev = &pdev->dev;
> > +
> > +	lpg->map = dev_get_regmap(pdev->dev.parent, NULL);
> > +	if (!lpg->map) {
> > +		dev_err(&pdev->dev, "parent regmap unavailable\n");
> > +		return -ENXIO;
> > +	}
> > +
> > +	ret = lpg_init_channels(lpg);
> > +	if (ret < 0)
> > +		return ret;
> > +
> > +	ret = lpg_init_triled(lpg);
> > +	if (ret < 0)
> > +		return ret;
> > +
> > +	ret = lpg_init_lut(lpg);
> > +	if (ret < 0)
> > +		return ret;
> 
> 
> How about turning these returns into dev_err_probe?  I'm not sure if that's
> the expected way to go nowadays, but having some form of logging when a
> driver fails to probe is always good to have.
> 

The intention is that each code path through these functions will either
pass or spit out an error in the log. I looked through them again and
think I cover all paths...

Thanks,
Bjorn

  reply	other threads:[~2021-04-28 22:39 UTC|newest]

Thread overview: 22+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-10-21 20:12 [PATCH v6 0/4] Qualcomm Light Pulse Generator Bjorn Andersson
2020-10-21 20:12 ` [PATCH v6 1/4] dt-bindings: leds: Add Qualcomm Light Pulse Generator binding Bjorn Andersson
2020-10-26 15:02   ` Rob Herring
2020-10-21 20:12 ` [PATCH v6 2/4] leds: Add driver for Qualcomm LPG Bjorn Andersson
2020-10-22 19:25   ` Luca Weiss
2020-10-29 18:13   ` Pavel Machek
2021-04-29  0:12     ` Bjorn Andersson
2021-04-29 21:12       ` Pavel Machek
2021-04-29 21:29         ` Bjorn Andersson
2021-05-04 15:43           ` Pavel Machek
2021-05-04 16:13             ` Bjorn Andersson
2021-05-05  5:21               ` Uwe Kleine-König
2021-04-18 21:54   ` Marijn Suijten
2021-04-28 22:39     ` Bjorn Andersson [this message]
2021-04-29 19:31       ` Marijn Suijten
2021-04-29 20:54         ` Bjorn Andersson
2021-05-05  5:15   ` Uwe Kleine-König
2021-05-05  5:19     ` Uwe Kleine-König
2021-05-13 17:43     ` Bjorn Andersson
2020-10-21 20:12 ` [PATCH v6 3/4] arm64: dts: qcom: pm(i)8994: Add mpp and lpg blocks Bjorn Andersson
2020-10-21 20:12 ` [PATCH v6 4/4] arm64: dts: qcom: Add user LEDs on db820c Bjorn Andersson
2021-04-15 10:46 [PATCH v6 2/4] leds: Add driver for Qualcomm LPG Yassine Oudjana

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210428223939.GN1908499@yoga \
    --to=bjorn.andersson@linaro.org \
    --cc=agross@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=dmurphy@ti.com \
    --cc=lee.jones@linaro.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-leds@vger.kernel.org \
    --cc=linux-pwm@vger.kernel.org \
    --cc=marijn.suijten@somainline.org \
    --cc=martin.botka1@gmail.com \
    --cc=pavel@ucw.cz \
    --cc=robh+dt@kernel.org \
    --cc=thierry.reding@gmail.com \
    --cc=u.kleine-koenig@pengutronix.de \
    --subject='Re: [PATCH v6 2/4] leds: Add driver for Qualcomm LPG' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).