From: Obeida Shamoun <oshmoun100@googlemail.com> [ Upstream commit cdfd4c689e2a52c313b35ddfc1852ff274f91acb ] WLED3_SINK_REG_SYNC is, as the name implies, a sink register offset. Therefore, use the sink address as base instead of the ctrl address. This fixes the sync toggle on wled4, which can be observed by the fact that adjusting brightness now works. It has no effect on wled3 because sink and ctrl base addresses are the same. This allows adjusting the brightness without having to disable then reenable the module. Signed-off-by: Obeida Shamoun <oshmoun100@googlemail.com> Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org> Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Acked-by: Kiran Gunda <kgunda@codeaurora.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> --- drivers/video/backlight/qcom-wled.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/video/backlight/qcom-wled.c b/drivers/video/backlight/qcom-wled.c index 3bc7800eb0a9..83a187fdaa1d 100644 --- a/drivers/video/backlight/qcom-wled.c +++ b/drivers/video/backlight/qcom-wled.c @@ -336,13 +336,13 @@ static int wled3_sync_toggle(struct wled *wled) unsigned int mask = GENMASK(wled->max_string_count - 1, 0); rc = regmap_update_bits(wled->regmap, - wled->ctrl_addr + WLED3_SINK_REG_SYNC, + wled->sink_addr + WLED3_SINK_REG_SYNC, mask, mask); if (rc < 0) return rc; rc = regmap_update_bits(wled->regmap, - wled->ctrl_addr + WLED3_SINK_REG_SYNC, + wled->sink_addr + WLED3_SINK_REG_SYNC, mask, WLED3_SINK_REG_SYNC_CLEAR); return rc; -- 2.30.2
From: Kiran Gunda <kgunda@codeaurora.org> [ Upstream commit 4d6e9cdff7fbb6bef3e5559596fab3eeffaf95ca ] Currently, for WLED5, the FSC (Full scale current) setting is not updated properly due to driver toggling the wrong register after an FSC update. On WLED5 we should only toggle the MOD_SYNC bit after a brightness update. For an FSC update we need to toggle the SYNC bits instead. Fix it by adopting the common wled3_sync_toggle() for WLED5 and introducing new code to the brightness update path to compensate. Signed-off-by: Kiran Gunda <kgunda@codeaurora.org> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> --- drivers/video/backlight/qcom-wled.c | 25 +++++++++++++++++++------ 1 file changed, 19 insertions(+), 6 deletions(-) diff --git a/drivers/video/backlight/qcom-wled.c b/drivers/video/backlight/qcom-wled.c index 83a187fdaa1d..cd11c5776438 100644 --- a/drivers/video/backlight/qcom-wled.c +++ b/drivers/video/backlight/qcom-wled.c @@ -348,7 +348,7 @@ static int wled3_sync_toggle(struct wled *wled) return rc; } -static int wled5_sync_toggle(struct wled *wled) +static int wled5_mod_sync_toggle(struct wled *wled) { int rc; u8 val; @@ -445,10 +445,23 @@ static int wled_update_status(struct backlight_device *bl) goto unlock_mutex; } - rc = wled->wled_sync_toggle(wled); - if (rc < 0) { - dev_err(wled->dev, "wled sync failed rc:%d\n", rc); - goto unlock_mutex; + if (wled->version < 5) { + rc = wled->wled_sync_toggle(wled); + if (rc < 0) { + dev_err(wled->dev, "wled sync failed rc:%d\n", rc); + goto unlock_mutex; + } + } else { + /* + * For WLED5 toggling the MOD_SYNC_BIT updates the + * brightness + */ + rc = wled5_mod_sync_toggle(wled); + if (rc < 0) { + dev_err(wled->dev, "wled mod sync failed rc:%d\n", + rc); + goto unlock_mutex; + } } } @@ -1459,7 +1472,7 @@ static int wled_configure(struct wled *wled) size = ARRAY_SIZE(wled5_opts); *cfg = wled5_config_defaults; wled->wled_set_brightness = wled5_set_brightness; - wled->wled_sync_toggle = wled5_sync_toggle; + wled->wled_sync_toggle = wled3_sync_toggle; wled->wled_cabc_config = wled5_cabc_config; wled->wled_ovp_delay = wled5_ovp_delay; wled->wled_auto_detection_required = -- 2.30.2