[PATCH v2] arm64: dts: qcom: sm8350: fix the node unit addresses

[PATCH v2] arm64: dts: qcom: sm8350: fix the node unit addresses

[Vinod Koul]

Some node unit addresses were put wrongly in the dts, resulting in
below warning when run with W=1

arch/arm64/boot/dts/qcom/sm8350.dtsi:693.34-702.5: Warning (simple_bus_reg): /soc@0/thermal-sensor@c222000: simple-bus unit address format error, expected "c263000"
arch/arm64/boot/dts/qcom/sm8350.dtsi:704.34-713.5: Warning (simple_bus_reg): /soc@0/thermal-sensor@c223000: simple-bus unit address format error, expected "c265000"
arch/arm64/boot/dts/qcom/sm8350.dtsi:1180.32-1185.5: Warning (simple_bus_reg): /soc@0/interconnect@90e0000: simple-bus unit address format error, expected "90c0000"

Fix by correcting to the correct address as given in reg node

Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---

changes in v2:
 - drop the interconnect header included worngly in this patch

 arch/arm64/boot/dts/qcom/sm8350.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index cdeea45a2b2c..d015a9ca95a5 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -690,7 +690,7 @@ pdc: interrupt-controller@b220000 {
 			interrupt-controller;
 		};
 
-		tsens0: thermal-sensor@c222000 {
+		tsens0: thermal-sensor@c263000 {
 			compatible = "qcom,sm8350-tsens", "qcom,tsens-v2";
 			reg = <0 0x0c263000 0 0x1ff>, /* TM */
 			      <0 0x0c222000 0 0x8>; /* SROT */
@@ -701,7 +701,7 @@ tsens0: thermal-sensor@c222000 {
 			#thermal-sensor-cells = <1>;
 		};
 
-		tsens1: thermal-sensor@c223000 {
+		tsens1: thermal-sensor@c265000 {
 			compatible = "qcom,sm8350-tsens", "qcom,tsens-v2";
 			reg = <0 0x0c265000 0 0x1ff>, /* TM */
 			      <0 0x0c223000 0 0x8>; /* SROT */
@@ -1177,7 +1177,7 @@ usb_2_ssphy: phy@88ebe00 {
 			};
 		};
 
-		dc_noc: interconnect@90e0000 {
+		dc_noc: interconnect@90c0000 {
 			compatible = "qcom,sm8350-dc-noc";
 			reg = <0 0x090c0000 0 0x4200>;
 			#interconnect-cells = <1>;
-- 
2.26.3

Re: [PATCH v2] arm64: dts: qcom: sm8350: fix the node unit addresses

[patchwork-bot+linux-arm-msm]

Hello:

This patch was applied to qcom/linux.git (refs/heads/for-next):

On Thu, 13 May 2021 11:37:33 +0530 you wrote:
> Some node unit addresses were put wrongly in the dts, resulting in
> below warning when run with W=1
> 
> arch/arm64/boot/dts/qcom/sm8350.dtsi:693.34-702.5: Warning (simple_bus_reg): /soc@0/thermal-sensor@c222000: simple-bus unit address format error, expected "c263000"
> arch/arm64/boot/dts/qcom/sm8350.dtsi:704.34-713.5: Warning (simple_bus_reg): /soc@0/thermal-sensor@c223000: simple-bus unit address format error, expected "c265000"
> arch/arm64/boot/dts/qcom/sm8350.dtsi:1180.32-1185.5: Warning (simple_bus_reg): /soc@0/interconnect@90e0000: simple-bus unit address format error, expected "90c0000"
> 
> [...]

Here is the summary with links:
  - [v2] arm64: dts: qcom: sm8350: fix the node unit addresses
    https://git.kernel.org/qcom/c/1dee9e3b0997

You are awesome, thank you!
--
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html