[PATCH 00/17] CAMSS: SM8250 support (and some fixes)

From: Jonathan Marek <jonathan@marek.ca>
To: linux-arm-msm@vger.kernel.org
Cc: robert.foss@linaro.org, andrey.konovalov@linaro.org,
	Andy Gross <agross@kernel.org>,
	Bjorn Andersson <bjorn.andersson@linaro.org>,
	devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND
	FLATTENED DEVICE TREE BINDINGS),
	Hans Verkuil <hverkuil-cisco@xs4all.nl>,
	linux-kernel@vger.kernel.org (open list),
	linux-media@vger.kernel.org (open list:QUALCOMM CAMERA SUBSYSTEM
	DRIVER), Mauro Carvalho Chehab <mchehab@kernel.org>,
	Rob Herring <robh+dt@kernel.org>,
	Todor Tomov <todor.too@gmail.com>
Subject: [PATCH 00/17] CAMSS: SM8250 support (and some fixes)
Date: Tue,  8 Jun 2021 18:34:49 -0400	[thread overview]
Message-ID: <20210608223513.23193-1-jonathan@marek.ca> (raw)

This adds initial support for SM8250 and its 4 VFEs and 6 CSIPHYs.
The only big change is the added camss-vfe-480.c to support the
Titan 480 VFE.

v2:
 - Fixed some typos in commit messages (patches 02 and 08)
 - patch 03 ("media: camss: csiphy-3ph: add support for SM8250 CSI DPHY"):
   - moved definition of CAMSS_8250 to this patch,
   - removed unused lane_enable variable
   - added a default unreachable case to avoid a warning
   - added a is_gen2 variable (minor rework)
 - Undo DECODE_FORMAT_PAYLOAD_ONLY change, add comment instead (patch 04)
 - "ops" reworks in addition to removing dead code (patch 12)
 - renamed csid-170 to csid-gen2, added defines for offsets, add missing
   camnoc_axi clock to sm8250 vfe resources (patch 16/17)

Jonathan Marek (17):
  media: camss: csiphy-3ph: don't print HW version as an error
  media: camss: csiphy-3ph: disable interrupts
  media: camss: csiphy-3ph: add support for SM8250 CSI DPHY
  media: camss: csid-170: fix non-10bit formats
  media: camss: csid-170: don't enable unused irqs
  media: camss: csid-170: remove stray comment
  media: camss: csid-170: support more than one lite vfe
  media: camss: csid-170: set the right HALT_CMD when disabled
  media: camss: csid: allow csid to work without a regulator
  media: camss: remove vdda-csiN from sdm845 resources
  media: camss: fix VFE irq name
  media: camss: remove some vfe ops and clean up dead vfe-170 code
  media: camss: vfe-170: fix "VFE halt timeout" error
  media: camss: Add initial support for VFE hardware version Titan 480
  media: camss: add support for V4L2_PIX_FMT_GREY for sdm845 HW
  media: camss: add support for SM8250 camss
  media: dt-bindings: media: camss: Add qcom,sm8250-camss binding

 .../bindings/media/qcom,sm8250-camss.yaml     | 399 +++++++++++++
 drivers/media/platform/qcom/camss/Makefile    |   3 +-
 .../{camss-csid-170.c => camss-csid-gen2.c}   |  32 +-
 .../media/platform/qcom/camss/camss-csid.c    |  45 +-
 .../media/platform/qcom/camss/camss-csid.h    |   2 +-
 .../qcom/camss/camss-csiphy-3ph-1-0.c         | 184 ++++--
 .../media/platform/qcom/camss/camss-csiphy.c  |   9 +-
 .../media/platform/qcom/camss/camss-vfe-170.c | 101 +---
 .../media/platform/qcom/camss/camss-vfe-4-1.c |  25 +-
 .../media/platform/qcom/camss/camss-vfe-4-7.c |  63 +-
 .../media/platform/qcom/camss/camss-vfe-4-8.c |  65 +--
 .../media/platform/qcom/camss/camss-vfe-480.c | 545 ++++++++++++++++++
 .../platform/qcom/camss/camss-vfe-gen1.c      |  94 +--
 .../platform/qcom/camss/camss-vfe-gen1.h      |  39 +-
 drivers/media/platform/qcom/camss/camss-vfe.c |  29 +-
 drivers/media/platform/qcom/camss/camss-vfe.h |  17 +-
 .../media/platform/qcom/camss/camss-video.c   |   5 +-
 drivers/media/platform/qcom/camss/camss.c     | 205 ++++++-
 drivers/media/platform/qcom/camss/camss.h     |   1 +
 19 files changed, 1523 insertions(+), 340 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/media/qcom,sm8250-camss.yaml
 rename drivers/media/platform/qcom/camss/{camss-csid-170.c => camss-csid-gen2.c} (95%)
 create mode 100644 drivers/media/platform/qcom/camss/camss-vfe-480.c

-- 
2.26.1