linux-arm-msm.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
To: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: lorenzo.pieralisi@arm.com, robh@kernel.org, bhelgaas@google.com,
	linux-arm-msm@vger.kernel.org, linux-pci@vger.kernel.org,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	Siddartha Mohanadoss <smohanad@codeaurora.org>
Subject: Re: [PATCH v2 2/3] PCI: dwc: Add Qualcomm PCIe Endpoint controller driver
Date: Wed, 9 Jun 2021 14:21:52 +0530	[thread overview]
Message-ID: <20210609085152.GB15118@thinkpad> (raw)
In-Reply-To: <YLw744UeM6fj/xoS@builder.lan>

On Sat, Jun 05, 2021 at 10:07:15PM -0500, Bjorn Andersson wrote:
> On Thu 03 Jun 05:38 CDT 2021, Manivannan Sadhasivam wrote:
> 
> > Add driver support for Qualcomm PCIe Endpoint controller driver based on
> > the Designware core with added Qualcomm specific wrapper around the
> > core. The driver support is very basic such that it supports only
> > enumeration, PCIe read/write, and MSI. There is no ASPM and PM support
> > for now but these will be added later.
> > 
> > The driver is capable of using the PERST# and WAKE# side-band GPIOs for
> > operation and written on top of the DWC PCI framework.
> > 
> > Co-developed-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
> > Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
> > [mani: restructured the driver and fixed several bugs for upstream]
> > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> 
> Really nice to see this working!
> 
> > ---
> >  drivers/pci/controller/dwc/Kconfig        |  10 +
> >  drivers/pci/controller/dwc/Makefile       |   1 +
> >  drivers/pci/controller/dwc/pcie-qcom-ep.c | 780 ++++++++++++++++++++++
> >  3 files changed, 791 insertions(+)
> >  create mode 100644 drivers/pci/controller/dwc/pcie-qcom-ep.c
> > 
> > diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
> > index 423d35872ce4..32e735b1fd85 100644
> > --- a/drivers/pci/controller/dwc/Kconfig
> > +++ b/drivers/pci/controller/dwc/Kconfig
> > @@ -180,6 +180,16 @@ config PCIE_QCOM
> >  	  PCIe controller uses the DesignWare core plus Qualcomm-specific
> >  	  hardware wrappers.
> >  
> > +config PCIE_QCOM_EP
> > +	bool "Qualcomm PCIe controller - Endpoint mode"
> > +	depends on OF && (ARCH_QCOM || COMPILE_TEST)
> > +	depends on PCI_ENDPOINT
> > +	select PCIE_DW_EP
> > +	help
> > +	  Say Y here to enable support for the PCIe controllers on Qualcomm SoCs
> > +	  to work in endpoint mode. The PCIe controller uses the DesignWare core
> > +	  plus Qualcomm-specific hardware wrappers.
> > +
> >  config PCIE_ARMADA_8K
> >  	bool "Marvell Armada-8K PCIe controller"
> >  	depends on ARCH_MVEBU || COMPILE_TEST
> > diff --git a/drivers/pci/controller/dwc/Makefile b/drivers/pci/controller/dwc/Makefile
> > index eca805c1a023..abb27642d46b 100644
> > --- a/drivers/pci/controller/dwc/Makefile
> > +++ b/drivers/pci/controller/dwc/Makefile
> > @@ -12,6 +12,7 @@ obj-$(CONFIG_PCI_KEYSTONE) += pci-keystone.o
> >  obj-$(CONFIG_PCI_LAYERSCAPE) += pci-layerscape.o
> >  obj-$(CONFIG_PCI_LAYERSCAPE_EP) += pci-layerscape-ep.o
> >  obj-$(CONFIG_PCIE_QCOM) += pcie-qcom.o
> > +obj-$(CONFIG_PCIE_QCOM_EP) += pcie-qcom-ep.o
> >  obj-$(CONFIG_PCIE_ARMADA_8K) += pcie-armada8k.o
> >  obj-$(CONFIG_PCIE_ARTPEC6) += pcie-artpec6.o
> >  obj-$(CONFIG_PCIE_INTEL_GW) += pcie-intel-gw.o
> > diff --git a/drivers/pci/controller/dwc/pcie-qcom-ep.c b/drivers/pci/controller/dwc/pcie-qcom-ep.c
> > new file mode 100644
> > index 000000000000..b68511bacc2a
> > --- /dev/null
> > +++ b/drivers/pci/controller/dwc/pcie-qcom-ep.c
> > @@ -0,0 +1,780 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Qualcomm PCIe Endpoint controller driver
> > + *
> > + * Copyright (c) 2020, The Linux Foundation. All rights reserved.
> > + * Author: Siddartha Mohanadoss <smohanad@codeaurora.org
> > + *
> > + * Copyright (c) 2021, Linaro Ltd.
> > + * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org
> > + */
> > +
> > +#include <linux/clk.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/gpio/consumer.h>
> > +#include <linux/reset.h>
> > +#include <linux/delay.h>
> > +#include <linux/phy/phy.h>
> > +#include <linux/pm_domain.h>
> > +
> > +#include "pcie-designware.h"
> > +
> > +/* PARF registers */
> > +#define PARF_SYS_CTRL				0x00
> > +#define PARF_DB_CTRL				0x10
> > +#define PARF_PM_CTRL				0x20
> > +#define PARF_DEBUG_INT_EN			0x190
> > +#define PARF_AXI_MSTR_RD_HALT_NO_WRITES		0x1a4
> > +#define PARF_AXI_MSTR_WR_ADDR_HALT		0x1a8
> > +#define PARF_Q2A_FLUSH				0x1aC
> > +#define PARF_LTSSM				0x1b0
> > +#define PARF_CFG_BITS				0x210
> > +#define PARF_INT_ALL_STATUS			0x224
> > +#define PARF_INT_ALL_CLEAR			0x228
> > +#define PARF_INT_ALL_MASK			0x22c
> > +#define PARF_SLV_ADDR_MSB_CTRL			0x2c0
> > +#define PARF_DBI_BASE_ADDR			0x350
> > +#define PARF_DBI_BASE_ADDR_HI			0x354
> > +#define PARF_SLV_ADDR_SPACE_SIZE		0x358
> > +#define PARF_SLV_ADDR_SPACE_SIZE_HI		0x35c
> > +#define PARF_ATU_BASE_ADDR			0x634
> > +#define PARF_ATU_BASE_ADDR_HI			0x638
> > +#define PARF_SRIS_MODE				0x644
> > +#define PARF_DEVICE_TYPE			0x1000
> > +#define PARF_BDF_TO_SID_CFG			0x2c00
> > +
> > +/* ELBI registers */
> > +#define ELBI_SYS_STTS				0x08
> > +
> > +/* DBI registers */
> > +#define DBI_CAP_ID_NXT_PTR			0x40
> > +#define DBI_CON_STATUS				0x44
> > +#define DBI_DEVICE_CAPABILITIES			0x74
> > +#define DBI_LINK_CAPABILITIES			0x7c
> > +#define DBI_LINK_CONTROL2_LINK_STATUS2		0xa0
> > +#define DBI_L1SUB_CAPABILITY			0x234
> > +#define DBI_ACK_F_ASPM_CTRL			0x70c
> > +#define DBI_GEN3_RELATED_OFF			0x890
> > +#define DBI_AUX_CLK_FREQ			0xb40
> > +
> > +#define DBI_L0S_ACCPT_LATENCY_MASK		GENMASK(8, 6)
> > +#define DBI_L1_ACCPT_LATENCY_MASK		GENMASK(11, 9)
> > +#define DBI_L0S_EXIT_LATENCY_MASK		GENMASK(14, 12)
> > +#define DBI_L1_EXIT_LATENCY_MASK		GENMASK(17, 15)
> > +#define DBI_ACK_N_FTS_MASK			GENMASK(15, 8)
> > +
> > +/* TCSR registers */
> > +#define TCSR_PCIE_PERST_EN			0x258
> > +#define TCSR_PERST_SEPARATION_ENABLE		0x270
> > +
> > +#define XMLH_LINK_UP				0x400
> > +#define CORE_RESET_TIME_US_MIN			1000
> > +#define CORE_RESET_TIME_US_MAX			1005
> > +#define WAKE_DELAY_US				2000 /* 2 ms */
> > +
> > +#define to_pcie_ep(x)				dev_get_drvdata((x)->dev)
> 
> Isn't this also container_of(x, struct qcom_pcie_ep, pci), but without
> the need to assigning and use drvdata?
> 

Okay

> > +
> > +enum qcom_pcie_ep_link_status {
> > +	QCOM_PCIE_EP_LINK_DISABLED,
> > +	QCOM_PCIE_EP_LINK_ENABLED,
> > +	QCOM_PCIE_EP_LINK_UP,
> > +	QCOM_PCIE_EP_LINK_DOWN,
> > +};
> > +
> > +enum qcom_pcie_ep_irq {
> > +	QCOM_PCIE_EP_INT_RESERVED,
> > +	QCOM_PCIE_EP_INT_LINK_DOWN,
> > +	QCOM_PCIE_EP_INT_BME,
> > +	QCOM_PCIE_EP_INT_PM_TURNOFF,
> > +	QCOM_PCIE_EP_INT_DEBUG,
> > +	QCOM_PCIE_EP_INT_LTR,
> > +	QCOM_PCIE_EP_INT_MHI_Q6,
> > +	QCOM_PCIE_EP_INT_MHI_A7,
> > +	QCOM_PCIE_EP_INT_DSTATE_CHANGE,
> > +	QCOM_PCIE_EP_INT_L1SUB_TIMEOUT,
> > +	QCOM_PCIE_EP_INT_MMIO_WRITE,
> > +	QCOM_PCIE_EP_INT_CFG_WRITE,
> > +	QCOM_PCIE_EP_INT_BRIDGE_FLUSH_N,
> > +	QCOM_PCIE_EP_INT_LINK_UP,
> > +	QCOM_PCIE_EP_INT_AER_LEGACY,
> > +	QCOM_PCIE_EP_INT_PLS_ERR,
> > +	QCOM_PCIE_EP_INT_PME_LEGACY,
> > +	QCOM_PCIE_EP_INT_PLS_PME,
> > +	QCOM_PCIE_EP_INT_MAX,
> 
> Afaict these aren't some logical sequence of numbers, they are bit
> offsets in the interrupt registers. Using #define would make this
> obvious.
> 

Yes but these are reused in the irqhandler for differentiating between the
events, so I thought it makes sense to use enum.

> > +};
> > +
> > +static struct clk_bulk_data qcom_pcie_ep_clks[] = {
> > +	{ .id = "cfg" },
> > +	{ .id = "aux" },
> > +	{ .id = "bus_master" },
> > +	{ .id = "bus_slave" },
> > +	{ .id = "ref" },
> > +	{ .id = "sleep" },
> > +	{ .id = "slave_q2a" },
> > +};
> > +
> > +struct qcom_pcie_ep {
> > +	struct dw_pcie pci;
> > +
> > +	void __iomem *parf;
> > +	void __iomem *elbi;
> > +	void __iomem *tcsr;
> > +
> > +	struct reset_control *core_reset;
> > +	struct gpio_desc *reset;
> > +	struct gpio_desc *wake;
> > +	struct phy *phy;
> > +
> > +	resource_size_t dbi_phys;
> > +	resource_size_t atu_phys;
> > +
> > +	enum qcom_pcie_ep_link_status link_status;
> > +	int global_irq;
> > +	int perst_irq;
> > +};
> > +
> > +static void qcom_pcie_ep_enable_ltssm(struct qcom_pcie_ep *pcie_ep)
> > +{
> > +	u32 reg;
> > +
> > +	reg = readl(pcie_ep->parf + PARF_LTSSM);
> > +	reg |= BIT(8);
> > +	writel_relaxed(reg, pcie_ep->parf + PARF_LTSSM);
> > +}
> > +
> > +static int qcom_pcie_ep_core_reset(struct qcom_pcie_ep *pcie_ep)
> > +{
> > +	struct dw_pcie *pci = &pcie_ep->pci;
> > +	struct device *dev = pci->dev;
> > +	int ret = 0;
> 
> No need to initialize ret, when the first access is an assignment.
> 
> > +
> > +	ret = reset_control_assert(pcie_ep->core_reset);
> > +	if (ret) {
> > +		dev_err(dev, "Cannot assert core reset\n");
> > +		return ret;
> > +	}
> > +
> > +	usleep_range(CORE_RESET_TIME_US_MIN, CORE_RESET_TIME_US_MAX);
> > +
> > +	ret = reset_control_deassert(pcie_ep->core_reset);
> > +	if (ret) {
> > +		dev_err(dev, "Cannot de-assert core reset\n");
> > +		return ret;
> > +	}
> > +
> > +	usleep_range(CORE_RESET_TIME_US_MIN, CORE_RESET_TIME_US_MAX);
> > +
> > +	return 0;
> > +}
> > +
> > +/*
> > + * Delatch PERST_EN and PERST_SEPARATION_ENABLE with TCSR to avoid
> > + * device reset during host reboot and hibernation. The driver is
> > + * expected to handle this situation.
> > + */
> > +static void qcom_pcie_ep_configure_tcsr(struct qcom_pcie_ep *pcie_ep)
> > +{
> > +	writel_relaxed(0x0, pcie_ep->tcsr + TCSR_PCIE_PERST_EN);
> 
> Please avoid _relaxed accessor unless there's a strong reason, and if so
> document it.
> 

Okay

> > +	writel_relaxed(0x0, pcie_ep->tcsr + TCSR_PERST_SEPARATION_ENABLE);
> > +}
> > +
> > +static int qcom_pcie_ep_enable_resources(struct qcom_pcie_ep *pcie_ep)
> > +{
> > +	struct dw_pcie *pci = &pcie_ep->pci;
> > +	struct device *dev = pci->dev;
> > +	int ret;
> > +
> > +	ret = clk_bulk_prepare_enable(ARRAY_SIZE(qcom_pcie_ep_clks),
> > +				      qcom_pcie_ep_clks);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to enable clocks: %d\n", ret);
> 
> clk_bulk_prepare_enable() will print an error indicating which of the
> clocks it failed to prepare/enable, so it's better to skip this.
> 
> As such, you can simply do:
> 
> 	return clk_bulk_prepare_enable();
> 
> > +		return ret;
> > +	}
> > +
> > +	return 0;
> > +}
> > +
> > +static void qcom_pcie_ep_disable_resources(struct qcom_pcie_ep *pcie_ep)
> > +{
> > +	clk_bulk_disable_unprepare(ARRAY_SIZE(qcom_pcie_ep_clks),
> > +				   qcom_pcie_ep_clks);
> > +}
> > +
> > +static void qcom_pcie_ep_configure_irq(struct qcom_pcie_ep *pcie_ep)
> > +{
> > +	u32 val;
> > +
> > +	writel_relaxed(0, pcie_ep->parf + PARF_INT_ALL_MASK);
> > +	val = BIT(QCOM_PCIE_EP_INT_LINK_DOWN) |
> > +		BIT(QCOM_PCIE_EP_INT_BME) |
> > +		BIT(QCOM_PCIE_EP_INT_PM_TURNOFF) |
> > +		BIT(QCOM_PCIE_EP_INT_DSTATE_CHANGE) |
> > +		BIT(QCOM_PCIE_EP_INT_LINK_UP);
> > +	writel_relaxed(val, pcie_ep->parf + PARF_INT_ALL_MASK);
> 
> Again, please avoid the _relaxed versions.
> 
> > +}
> > +
> > +static int qcom_pcie_ep_core_init(struct qcom_pcie_ep *pcie_ep)
> > +{
> > +	struct dw_pcie *pci = &pcie_ep->pci;
> > +	u32 val;
> > +
> > +	/* Disable BDF to SID mapping */
> > +	val = readl_relaxed(pcie_ep->parf + PARF_BDF_TO_SID_CFG);
> > +	val |= BIT(0);
> > +	writel_relaxed(val, pcie_ep->parf + PARF_BDF_TO_SID_CFG);
> > +
> > +	/* enable debug IRQ */
> > +	writel_relaxed((BIT(3) | BIT(2) | BIT(1)),
> > +		       pcie_ep->parf + PARF_DEBUG_INT_EN);
> > +
> > +	/* Configure PCIe to endpoint mode */
> > +	writel_relaxed(0x0, pcie_ep->parf + PARF_DEVICE_TYPE);
> > +
> > +	/* Configure PCIe core to support 1GB aperture */
> > +	writel_relaxed(0x40000000, pcie_ep->parf + PARF_SLV_ADDR_SPACE_SIZE);
> > +
> > +	/* Allow entering L1 state */
> > +	val = readl_relaxed(pcie_ep->parf + PARF_PM_CTRL);
> > +	val &= ~BIT(5);
> > +	writel_relaxed(val, pcie_ep->parf + PARF_PM_CTRL);
> > +
> > +	/* Configure Slave, DBI and iATU base addresses */
> > +	writel_relaxed(BIT(0), pcie_ep->parf + PARF_SLV_ADDR_MSB_CTRL);
> > +	writel_relaxed(0x200, pcie_ep->parf + PARF_SLV_ADDR_SPACE_SIZE_HI);
> > +	writel_relaxed(0x0, pcie_ep->parf + PARF_SLV_ADDR_SPACE_SIZE);
> > +	writel_relaxed(0x100, pcie_ep->parf + PARF_DBI_BASE_ADDR_HI);
> > +	writel_relaxed(pcie_ep->dbi_phys, pcie_ep->parf + PARF_DBI_BASE_ADDR);
> > +	writel_relaxed(0x100, pcie_ep->parf + PARF_ATU_BASE_ADDR_HI);
> > +	writel_relaxed(pcie_ep->atu_phys, pcie_ep->parf + PARF_ATU_BASE_ADDR);
> > +
> > +	/* Read halts write */
> > +	writel_relaxed(0x0, pcie_ep->parf + PARF_AXI_MSTR_RD_HALT_NO_WRITES);
> > +	/* Write after write halt */
> > +	writel_relaxed(BIT(31), pcie_ep->parf + PARF_AXI_MSTR_WR_ADDR_HALT);
> > +	/* Q2A flush disable */
> > +	writel_relaxed(0, pcie_ep->parf + PARF_Q2A_FLUSH);
> > +
> > +	/* Disable the DBI Wakeup */
> > +	writel_relaxed(BIT(11), pcie_ep->parf + PARF_SYS_CTRL);
> > +	/* Disable the debouncers */
> > +	writel_relaxed(0x73, pcie_ep->parf + PARF_DB_CTRL);
> > +	/* Disable core clock CGC */
> > +	writel_relaxed(BIT(6), pcie_ep->parf + PARF_SYS_CTRL);
> > +	/* Set AUX power to be on */
> > +	writel_relaxed(BIT(4), pcie_ep->parf + PARF_SYS_CTRL);
> > +	/* Request to exit from L1SS for MSI and LTR MSG */
> > +	writel_relaxed(BIT(1), pcie_ep->parf + PARF_CFG_BITS);
> > +
> > +	dw_pcie_dbi_ro_wr_en(pci);
> > +
> > +	/* Set the PMC Register - to support PME in D0/D3hot/D3cold */
> > +	val = dw_pcie_readl_dbi(pci, DBI_CAP_ID_NXT_PTR);
> > +	val |= BIT(31) | BIT(30) | BIT(27);
> > +	dw_pcie_writel_dbi(pci, DBI_CAP_ID_NXT_PTR, val);
> > +
> > +	/* Set the Endpoint L0s Acceptable Latency to 1us (max) */
> > +	val = dw_pcie_readl_dbi(pci, DBI_DEVICE_CAPABILITIES);
> > +	val |= FIELD_PREP(DBI_L0S_ACCPT_LATENCY_MASK, 0x7);
> > +	dw_pcie_writel_dbi(pci, DBI_DEVICE_CAPABILITIES, val);
> > +
> > +	/* Set the Endpoint L1 Acceptable Latency to 1us (max) */
> > +	val = dw_pcie_readl_dbi(pci, DBI_DEVICE_CAPABILITIES);
> > +	val |= FIELD_PREP(DBI_L1_ACCPT_LATENCY_MASK, 0x7);
> > +	dw_pcie_writel_dbi(pci, DBI_DEVICE_CAPABILITIES, val);
> > +
> > +	/* Set the L0s Exit Latency to 2us-4us = 0x6 */
> > +	val = dw_pcie_readl_dbi(pci, DBI_LINK_CAPABILITIES);
> > +	val |= FIELD_PREP(DBI_L0S_EXIT_LATENCY_MASK, 0x6);
> > +	dw_pcie_writel_dbi(pci, DBI_LINK_CAPABILITIES, val);
> > +
> > +	/* Set the L1 Exit Latency to be 32us-64 us = 0x6 */
> > +	val = dw_pcie_readl_dbi(pci, DBI_LINK_CAPABILITIES);
> > +	val |= FIELD_PREP(DBI_L1_EXIT_LATENCY_MASK, 0x6);
> > +	dw_pcie_writel_dbi(pci, DBI_LINK_CAPABILITIES, val);
> > +
> > +	/* L1ss is supported */
> > +	val = dw_pcie_readl_dbi(pci, DBI_L1SUB_CAPABILITY);
> > +	val |= 0x1f;
> > +	dw_pcie_writel_dbi(pci, DBI_L1SUB_CAPABILITY, val);
> > +
> > +	/* Enable Clock Power Management */
> > +	val = dw_pcie_readl_dbi(pci, DBI_LINK_CAPABILITIES);
> > +	val |= BIT(18);
> > +	dw_pcie_writel_dbi(pci, DBI_LINK_CAPABILITIES, val);
> > +
> > +	dw_pcie_dbi_ro_wr_dis(pci);
> > +
> > +	/* Set FTS value to match the PHY setting */
> > +	val = dw_pcie_readl_dbi(pci, DBI_ACK_F_ASPM_CTRL);
> > +	val |= FIELD_PREP(DBI_ACK_N_FTS_MASK, 0x80);
> > +	dw_pcie_writel_dbi(pci, DBI_ACK_F_ASPM_CTRL, val);
> > +
> > +	dw_pcie_writel_dbi(pci, DBI_AUX_CLK_FREQ, 0x14);
> > +
> > +	/* Prevent L1ss wakeup after 100ms */
> > +	val = dw_pcie_readl_dbi(pci, DBI_GEN3_RELATED_OFF);
> > +	val &= ~BIT(0);
> > +	dw_pcie_writel_dbi(pci, DBI_GEN3_RELATED_OFF, val);
> > +
> > +	/* Disable SRIS_MODE */
> > +	val = readl_relaxed(pcie_ep->parf + PARF_SRIS_MODE);
> > +	val &= ~BIT(0);
> > +	writel_relaxed(val, pcie_ep->parf + PARF_SRIS_MODE);
> > +
> > +	qcom_pcie_ep_configure_irq(pcie_ep);
> 
> Why is the irq part broken out to its own function?
> 

Hmm, I removed one other use of this function. So will just use the code
directly.

> > +
> > +	return 0;
> > +}
> > +
> > +static int qcom_pcie_confirm_linkup(struct dw_pcie *pci)
> > +{
> > +	struct qcom_pcie_ep *pcie_ep = to_pcie_ep(pci);
> > +	u32 reg;
> > +
> > +	reg = readl_relaxed(pcie_ep->elbi + ELBI_SYS_STTS);
> > +
> > +	return reg & XMLH_LINK_UP;
> > +}
> > +
> > +static int qcom_pcie_start_link(struct dw_pcie *pci)
> > +{
> > +	struct qcom_pcie_ep *pcie_ep = to_pcie_ep(pci);
> > +
> > +	enable_irq(pcie_ep->perst_irq);
> > +
> > +	return 0;
> > +}
> > +
> > +static int qcom_pcie_establish_link(struct dw_pcie *pci)
> > +{
> > +	struct qcom_pcie_ep *pcie_ep = to_pcie_ep(pci);
> > +	struct device *dev = pci->dev;
> > +	int ret;
> > +
> > +	if (pcie_ep->link_status == QCOM_PCIE_EP_LINK_ENABLED) {
> > +		dev_info(dev, "Link is already enabled\n");
> 
> Per qcom_pcie_ep_global_threaded_irq() it seems possible that the link
> is enabled but link_status != QCOM_PCIE_EP_LINK_ENABLED.
> 
> I'm also not sure how you can end up here with link_status == ENABLED;
> it starts off DISABLED and expect the first thing to happen is "perst"
> asserting, which would end up here and after that the only way you get
> here again is if perst is asserted again - without first being
> deasserted. So perhaps this is part of your manual edge detector?
> 

Well, in the downstream this function is called from multiple places like SYSERR
but looking further reveals that this check is not relevant here. Will remove.

> Perhaps it's not needed if you actually use edge detection on your
> interrupt?
> 
> > +		return 0;
> > +	}
> > +
> > +	/* Enable power and clocks */
> > +	ret = qcom_pcie_ep_enable_resources(pcie_ep);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to enable resources: %d\n", ret);
> > +		return ret;
> > +	}
> > +
> > +	/* Perform controller reset */
> > +	ret = qcom_pcie_ep_core_reset(pcie_ep);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to reset the core: %d\n", ret);
> > +		goto err_disable_resources;
> > +	}
> > +
> > +	/* Initialize PHY */
> > +	ret = phy_init(pcie_ep->phy);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to initialize PHY: %d\n", ret);
> > +		goto err_disable_resources;
> > +	}
> > +
> > +	/* Power ON PHY */
> > +	ret = phy_power_on(pcie_ep->phy);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to Power ON PHY: %d\n", ret);
> > +		goto err_phy_exit;
> > +	}
> > +
> > +	/* Assert WAKE# to RC to indicate device is ready */
> > +	gpiod_set_value_cansleep(pcie_ep->wake, 0);
> 
> Assert sounds like "activate" or "turn on", so I would prefer that you
> make this a logical 1 here and if the signal is inverted specify this
> when you're requesting the gpio.
> 

Okay

> > +	usleep_range(WAKE_DELAY_US, WAKE_DELAY_US + 500);
> > +	gpiod_set_value_cansleep(pcie_ep->wake, 1);
> > +
> > +	/* Configure TCSR */
> > +	qcom_pcie_ep_configure_tcsr(pcie_ep);
> > +
> > +	/* Initialize the controller */
> > +	ret = qcom_pcie_ep_core_init(pcie_ep);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to init controller: %d\n", ret);
> > +		goto err_phy_power_off;
> > +	}
> > +
> > +	ret = dw_pcie_ep_init_complete(&pcie_ep->pci.ep);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to complete initialization: %d\n", ret);
> > +		goto err_phy_power_off;
> > +	}
> > +
> > +	dw_pcie_ep_init_notify(&pcie_ep->pci.ep);
> > +
> > +	/* Enable LTSSM */
> > +	qcom_pcie_ep_enable_ltssm(pcie_ep);
> > +
> > +	return 0;
> > +/* TODO* assert reset? */
> > +err_phy_power_off:
> > +	phy_power_off(pcie_ep->phy);
> > +err_phy_exit:
> > +	phy_exit(pcie_ep->phy);
> > +err_disable_resources:
> > +	qcom_pcie_ep_disable_resources(pcie_ep);
> > +
> > +	return ret;
> > +}
> > +
> > +static void qcom_pcie_disable_link(struct dw_pcie *pci)
> > +{
> > +	struct qcom_pcie_ep *pcie_ep = to_pcie_ep(pci);
> > +	struct device *dev = pci->dev;
> > +
> > +	if (pcie_ep->link_status == QCOM_PCIE_EP_LINK_DISABLED) {
> > +		dev_info(dev, "Link is already disabled\n");
> 
> Why can disable_link happen both from the interrupt handler directly and
> from the dw_pcie_ops?
> 

Right, I think the PERST IRQ should be disabled here.

> > +		return;
> > +	}
> > +
> > +	phy_power_off(pcie_ep->phy);
> > +	phy_exit(pcie_ep->phy);
> > +	qcom_pcie_ep_disable_resources(pcie_ep);
> > +	pcie_ep->link_status = QCOM_PCIE_EP_LINK_DISABLED;
> > +}
> > +
> > +/* Common DWC controller ops */
> > +static const struct dw_pcie_ops pci_ops = {
> > +	.link_up = qcom_pcie_confirm_linkup,
> > +	.start_link = qcom_pcie_start_link,
> > +	.stop_link = qcom_pcie_disable_link,
> > +};
> > +
> > +static int qcom_pcie_ep_get_io_resources(struct platform_device *pdev,
> > +					 struct qcom_pcie_ep *pcie_ep)
> > +{
> > +	struct device *dev = &pdev->dev;
> > +	struct dw_pcie *pci = &pcie_ep->pci;
> > +	struct resource *res;
> > +
> > +	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "parf");
> > +	pcie_ep->parf = devm_ioremap_resource(dev, res);
> 
> Better make this devm_platform_ioremap_resource_byname(), or someone
> will send a patch the minute this code lands.
> 
> > +	if (IS_ERR(pcie_ep->parf))
> > +		return PTR_ERR(pcie_ep->parf);
> > +
> > +	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dbi");
> > +	pci->dbi_base = devm_pci_remap_cfg_resource(dev, res);
> > +	if (IS_ERR(pci->dbi_base))
> > +		return PTR_ERR(pci->dbi_base);
> > +	pci->dbi_base2 = pci->dbi_base;
> > +	pcie_ep->dbi_phys = res->start;
> > +
> > +	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "elbi");
> > +	pcie_ep->elbi = devm_pci_remap_cfg_resource(dev, res);
> > +	if (IS_ERR(pcie_ep->elbi))
> > +		return PTR_ERR(pcie_ep->elbi);
> > +
> > +	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "atu");
> > +	pci->atu_base = devm_pci_remap_cfg_resource(dev, res);
> > +	if (IS_ERR(pci->atu_base))
> > +		return PTR_ERR(pci->atu_base);
> > +	pcie_ep->atu_phys = res->start;
> > +
> > +	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "tcsr");
> > +	pcie_ep->tcsr = devm_ioremap_resource(dev, res);
> > +	if (IS_ERR(pcie_ep->tcsr))
> > +		return PTR_ERR(pcie_ep->tcsr);
> > +
> > +	return 0;
> > +}
> > +
> > +static int qcom_pcie_ep_get_resources(struct platform_device *pdev,
> > +				      struct qcom_pcie_ep *pcie_ep)
> > +{
> > +	struct device *dev = &pdev->dev;
> > +	int ret;
> > +
> > +	ret = qcom_pcie_ep_get_io_resources(pdev, pcie_ep);
> > +	if (ret) {
> > +		dev_err(&pdev->dev, "failed to get io resources %d\n", ret);
> > +		return ret;
> > +	}
> > +
> > +	/* Enable GDSC power domain */
> > +	ret = dev_pm_domain_attach(dev, true);
> 
> If you only have a single power-domain specified, then it would already
> be attached to "dev".
> 

Ah, right. Will remove this.

> > +	if (ret)
> > +		return ret;
> > +
> > +	ret = devm_clk_bulk_get(dev, ARRAY_SIZE(qcom_pcie_ep_clks),
> > +				qcom_pcie_ep_clks);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to get clocks: %d\n", ret);
> 
> Don't you already have a print in devm_clk_bulk_get()?
> 
> > +		return ret;
> > +	}
> > +
> > +	pcie_ep->core_reset = devm_reset_control_get_exclusive(dev, "core");
> > +	if (IS_ERR(pcie_ep->core_reset))
> > +		return PTR_ERR(pcie_ep->core_reset);
> > +
> > +	pcie_ep->reset = devm_gpiod_get(dev, "reset", GPIOD_IN);
> > +	if (IS_ERR(pcie_ep->reset))
> > +		return PTR_ERR(pcie_ep->reset);
> > +
> > +	pcie_ep->wake = devm_gpiod_get_optional(dev, "wake", GPIOD_OUT_HIGH);
> > +	if (IS_ERR(pcie_ep->wake))
> > +		return PTR_ERR(pcie_ep->wake);
> > +
> > +	pcie_ep->phy = devm_phy_optional_get(&pdev->dev, "pciephy");
> > +	if (IS_ERR(pcie_ep->phy))
> > +		ret = PTR_ERR(pcie_ep->phy);
> > +
> > +	return ret;
> > +}
> > +
> > +/* TODO: Notify clients about PCIe state change */
> > +static irqreturn_t qcom_pcie_ep_global_threaded_irq(int irq, void *data)
> > +{
> > +	struct qcom_pcie_ep *pcie_ep = data;
> > +	struct dw_pcie *pci = &pcie_ep->pci;
> > +	struct device *dev = pci->dev;
> > +	u32 status = readl(pcie_ep->parf + PARF_INT_ALL_STATUS);
> > +	u32 mask = readl(pcie_ep->parf + PARF_INT_ALL_MASK);
> > +	u32 dstate, event, val;
> > +
> > +	writel_relaxed(status, pcie_ep->parf + PARF_INT_ALL_CLEAR);
> > +	status &= mask;
> > +
> > +	for (event = 1; event < QCOM_PCIE_EP_INT_MAX; event++) {
> > +		if (status & BIT(event)) {
> 
> for_each_set_bit()
> 

ack

> > +			switch (event) {
> > +			case QCOM_PCIE_EP_INT_LINK_DOWN:
> > +				dev_info(dev, "Received Linkdown event\n");
> > +				pcie_ep->link_status = QCOM_PCIE_EP_LINK_DOWN;
> > +				break;
> > +			case QCOM_PCIE_EP_INT_BME:
> > +				dev_info(dev, "Received BME event. Link is enabled!\n");
> > +				pcie_ep->link_status = QCOM_PCIE_EP_LINK_ENABLED;
> > +				break;
> > +			case QCOM_PCIE_EP_INT_PM_TURNOFF:
> > +				dev_info(dev, "Received PM Turn-off event! Entering L23\n");
> > +				val = readl_relaxed(pcie_ep->parf + PARF_PM_CTRL);
> > +				val |= BIT(2);
> > +				writel_relaxed(val, pcie_ep->parf + PARF_PM_CTRL);
> > +				break;
> > +			case QCOM_PCIE_EP_INT_DSTATE_CHANGE:
> > +				dstate = dw_pcie_readl_dbi(pci, DBI_CON_STATUS) & 0x3;
> > +				dev_info(dev, "Received D%d state event\n", dstate);
> > +				if (dstate == 3) {
> > +					val = readl_relaxed(pcie_ep->parf + PARF_PM_CTRL);
> > +					val |= BIT(1);
> > +					writel_relaxed(val, pcie_ep->parf + PARF_PM_CTRL);
> > +				}
> > +				/* Handle D0 state change */
> > +				break;
> > +			case QCOM_PCIE_EP_INT_LINK_UP:
> > +				dev_info(dev, "Received Linkup event. Enumeration complete!\n");
> > +				dw_pcie_ep_linkup(&pci->ep);
> > +				pcie_ep->link_status = QCOM_PCIE_EP_LINK_UP;
> > +				break;
> > +			default:
> > +				dev_err(dev, "Received unknown event: %d\n", event);
> > +				break;
> > +			}
> > +		}
> > +	}
> > +
> > +	return IRQ_HANDLED;
> > +}
> > +
> > +static irqreturn_t qcom_pcie_ep_perst_threaded_irq(int irq, void *data)
> > +{
> > +	struct qcom_pcie_ep *pcie_ep = data;
> > +	struct dw_pcie *pci = &pcie_ep->pci;
> > +	struct device *dev = pci->dev;
> > +	u32 perst;
> > +
> > +	perst = gpiod_get_value(pcie_ep->reset);
> > +
> > +	if (perst) {
> > +		/* Start link training */
> > +		dev_info(dev, "PERST de-asserted by host. Starting link training!\n");
> > +		qcom_pcie_establish_link(pci);
> > +	} else {
> > +		/* Shutdown the link if the link is already on */
> > +		dev_info(dev, "PERST asserted by host. Shutting down the PCIe link!\n");
> > +		qcom_pcie_disable_link(pci);
> > +	}
> > +
> > +	/* Set trigger type based on the next expected value of perst gpio */
> > +	irq_set_irq_type(gpiod_to_irq(pcie_ep->reset),
> > +			 (perst ? IRQF_TRIGGER_LOW : IRQF_TRIGGER_HIGH));
> 
> Looks like you're manually implementing edge triggering, is there any
> reason for that? EDGE_BOTH seems to do the same thing...
> 

PERST is a level based signal, so I don't think we can use EDGE_BOTH here.

> > +
> > +	return IRQ_HANDLED;
> > +}
> > +
> > +static int qcom_pcie_ep_enable_irq_resources(struct platform_device *pdev,
> > +					     struct qcom_pcie_ep *pcie_ep)
> > +{
> > +	int irq, ret;
> > +
> > +	irq = platform_get_irq_byname(pdev, "global");
> > +	if (irq < 0) {
> > +		dev_err(&pdev->dev, "Failed to get Global IRQ\n");
> > +		return irq;
> > +	}
> > +
> > +	ret = devm_request_threaded_irq(&pdev->dev, irq, NULL,
> > +					qcom_pcie_ep_global_threaded_irq,
> > +					IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
> 
> Leave out the trigger and rely on DT.
> 

Okay

> > +					"global_irq", pcie_ep);
> > +	if (ret) {
> > +		dev_err(&pdev->dev, "Failed to request Global IRQ\n");
> > +		return ret;
> > +	}
> > +
> > +	pcie_ep->perst_irq = gpiod_to_irq(pcie_ep->reset);
> > +	irq_set_status_flags(pcie_ep->perst_irq, IRQ_NOAUTOEN);
> 
> Is the global interrupt needed for dw_pcie_ep_init()? Or could this
> simply be done when things are ready to handle the interrupts?
> 

No it is not needed. I can move this after dw_pcie_ep_init().

> > +	ret = devm_request_threaded_irq(&pdev->dev, pcie_ep->perst_irq, NULL,
> > +					qcom_pcie_ep_perst_threaded_irq,
> > +					IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
> > +					"perst_irq", pcie_ep);
> > +	if (ret) {
> > +		dev_err(&pdev->dev, "Failed to request PERST IRQ\n");
> > +		return ret;
> > +	}
> > +
> > +	return 0;
> > +}
> > +
> > +static int qcom_pcie_ep_raise_irq(struct dw_pcie_ep *ep, u8 func_no,
> > +				  enum pci_epc_irq_type type, u16 interrupt_num)
> > +{
> > +	struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
> > +
> > +	switch (type) {
> > +	case PCI_EPC_IRQ_LEGACY:
> > +		return dw_pcie_ep_raise_legacy_irq(ep, func_no);
> > +	case PCI_EPC_IRQ_MSI:
> > +		return dw_pcie_ep_raise_msi_irq(ep, func_no, interrupt_num);
> > +	default:
> > +		dev_err(pci->dev, "Unknown IRQ type\n");
> > +		return -EINVAL;
> > +	}
> > +}
> > +
> > +static const struct pci_epc_features qcom_pcie_epc_features = {
> > +	.linkup_notifier = true,
> > +	.core_init_notifier = true,
> > +	.msi_capable = true,
> > +	.msix_capable = false,
> > +};
> > +
> > +static const struct pci_epc_features *
> > +qcom_pcie_epc_get_features(struct dw_pcie_ep *pci_ep)
> > +{
> > +	return &qcom_pcie_epc_features;
> > +}
> > +
> > +static void qcom_pcie_ep_init(struct dw_pcie_ep *ep)
> > +{
> > +	struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
> > +	enum pci_barno bar;
> > +
> > +	for (bar = BAR_0; bar <= BAR_5; bar++)
> > +		dw_pcie_ep_reset_bar(pci, bar);
> > +}
> > +
> > +static struct dw_pcie_ep_ops pci_ep_ops = {
> > +	.ep_init = qcom_pcie_ep_init,
> > +	.raise_irq = qcom_pcie_ep_raise_irq,
> > +	.get_features = qcom_pcie_epc_get_features,
> > +};
> > +
> > +static const struct of_device_id qcom_pcie_ep_match[] = {
> > +	{ .compatible = "qcom,sdx55-pcie-ep", },
> > +	{ }
> > +};
> 
> Move this below the probe function.
> 
> > +
> > +static int qcom_pcie_ep_probe(struct platform_device *pdev)
> > +{
> > +	struct device *dev = &pdev->dev;
> > +	struct qcom_pcie_ep *pcie_ep;
> > +	int ret;
> > +
> > +	pcie_ep = devm_kzalloc(dev, sizeof(*pcie_ep), GFP_KERNEL);
> > +	if (!pcie_ep)
> > +		return -ENOMEM;
> > +
> > +	pcie_ep->pci.dev = dev;
> > +	pcie_ep->pci.ops = &pci_ops;
> > +	pcie_ep->pci.ep.ops = &pci_ep_ops;
> > +
> > +	ret = qcom_pcie_ep_get_resources(pdev, pcie_ep);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to get resources:%d\n", ret);
> 
> You printed an error in about half the error cases in
> qcom_pcie_ep_get_resources(), it would be better to ensure you print a
> specific error for each of the remaining cases there and "silently"
> return here.
> 
> Same comment for below cases.
> 

Okay

> > +		return ret;
> > +	}
> > +
> > +	/* Enable power and clocks */
> > +	ret = qcom_pcie_ep_enable_resources(pcie_ep);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to enable resources: %d\n", ret);
> > +		return ret;
> > +	}
> > +
> > +	/* Perform controller reset */
> > +	ret = qcom_pcie_ep_core_reset(pcie_ep);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to reset the core: %d\n", ret);
> > +		goto err_disable_resources;
> > +	}
> > +
> > +	/* Initialize PHY */
> > +	ret = phy_init(pcie_ep->phy);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to initialize PHY: %d\n", ret);
> > +		goto err_disable_resources;
> > +	}
> > +
> > +	/* PHY needs to be powered on for dw_pcie_ep_init() */
> > +	ret = phy_power_on(pcie_ep->phy);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to Power ON PHY: %d\n", ret);
> > +		goto err_phy_exit;
> > +	}
> > +
> > +	platform_set_drvdata(pdev, pcie_ep);
> > +
> > +	ret = qcom_pcie_ep_enable_irq_resources(pdev, pcie_ep);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to get IRQ resources %d\n", ret);
> > +		goto err_phy_power_off;
> > +	}
> > +
> > +	ret = dw_pcie_ep_init(&pcie_ep->pci.ep);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to initialize endpoint:%d\n", ret);
> > +		goto err_phy_power_off;
> > +	}
> > +
> > +	return 0;
> > +
> > +err_phy_power_off:
> 
> Your interrupts remains enabled until devres takes them down after
> returning, so I suspect you need to disable them here as well - at least
> before shutting down the clocks.
> 

Okay

> > +	phy_power_off(pcie_ep->phy);
> > +err_phy_exit:
> > +	phy_exit(pcie_ep->phy);
> > +err_disable_resources:
> > +	qcom_pcie_ep_disable_resources(pcie_ep);
> > +
> > +	return ret;
> > +}
> > +
> > +static struct platform_driver qcom_pcie_ep_driver = {
> > +	.probe	= qcom_pcie_ep_probe,
> > +	.driver	= {
> > +		.name		= "qcom-pcie-ep",
> 
> Skip the indentation of the '='.
> 
> > +		.suppress_bind_attrs = true,
> 
> Why do we suppress_bind_attrs?
> 

This driver doesn't support remove() callback and I don't think it is necessary
for this platform driver. So this flag is here to prevent unbind from sysfs.

Thanks,
Mani

> Regards,
> Bjorn
> 
> > +		.of_match_table	= qcom_pcie_ep_match,
> > +	},
> > +};
> > +builtin_platform_driver(qcom_pcie_ep_driver);
> > +
> > +MODULE_AUTHOR("Siddartha Mohanadoss <smohanad@codeaurora.org>");
> > +MODULE_AUTHOR("Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>");
> > +MODULE_DESCRIPTION("Qualcomm PCIe Endpoint controller driver");
> > +MODULE_LICENSE("GPL v2");
> > -- 
> > 2.25.1
> > 

  reply	other threads:[~2021-06-09  8:53 UTC|newest]

Thread overview: 17+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-06-03 10:38 [PATCH v2 0/3] Add Qualcomm PCIe Endpoint driver support Manivannan Sadhasivam
2021-06-03 10:38 ` [PATCH v2 1/3] dt-bindings: pci: Add devicetree binding for Qualcomm PCIe EP controller Manivannan Sadhasivam
2021-06-06  3:13   ` Bjorn Andersson
2021-06-10 21:46     ` Rob Herring
2021-06-03 10:38 ` [PATCH v2 2/3] PCI: dwc: Add Qualcomm PCIe Endpoint controller driver Manivannan Sadhasivam
2021-06-05 22:02   ` Stanimir Varbanov
2021-06-09  5:20     ` Manivannan Sadhasivam
2021-06-06  3:07   ` Bjorn Andersson
2021-06-09  8:51     ` Manivannan Sadhasivam [this message]
2021-06-11  4:28       ` Bjorn Andersson
2021-06-11  4:44         ` Manivannan Sadhasivam
2021-06-16 18:23       ` Manivannan Sadhasivam
2021-06-15 21:40     ` Rob Herring
2021-06-15 21:57       ` Bjorn Andersson
2021-06-15 22:20         ` Rob Herring
2021-06-15 22:58           ` Bjorn Andersson
2021-06-03 10:38 ` [PATCH v2 3/3] MAINTAINERS: Add entry for Qualcomm PCIe Endpoint driver and binding Manivannan Sadhasivam

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210609085152.GB15118@thinkpad \
    --to=manivannan.sadhasivam@linaro.org \
    --cc=bhelgaas@google.com \
    --cc=bjorn.andersson@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-pci@vger.kernel.org \
    --cc=lorenzo.pieralisi@arm.com \
    --cc=robh@kernel.org \
    --cc=smohanad@codeaurora.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).