From: Bhupesh Sharma <bhupesh.sharma@linaro.org> To: linux-arm-msm@vger.kernel.org Cc: bhupesh.sharma@linaro.org, bhupesh.linux@gmail.com, linux-gpio@vger.kernel.org, linux-kernel@vger.kernel.org, devicetree@vger.kernel.org, Linus Walleij <linus.walleij@linaro.org>, Liam Girdwood <lgirdwood@gmail.com>, Mark Brown <broonie@kernel.org>, Bjorn Andersson <bjorn.andersson@linaro.org>, Vinod Koul <vkoul@kernel.org>, Rob Herring <robh+dt@kernel.org>, Andy Gross <agross@kernel.org> Subject: [PATCH v2 08/10] arm64: dts: qcom: pmm8155au_1: Add base dts file Date: Tue, 15 Jun 2021 13:15:41 +0530 [thread overview] Message-ID: <20210615074543.26700-9-bhupesh.sharma@linaro.org> (raw) In-Reply-To: <20210615074543.26700-1-bhupesh.sharma@linaro.org> Add base DTS file for pmm8155au_1 along with GPIOs, power-on, rtc and vadc nodes. Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Vinod Koul <vkoul@kernel.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Andy Gross <agross@kernel.org> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org> --- arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi | 134 ++++++++++++++++++++++ 1 file changed, 134 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi diff --git a/arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi b/arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi new file mode 100644 index 000000000000..b04c28e54470 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi @@ -0,0 +1,134 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, Linaro Limited + */ + +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> +#include <dt-bindings/iio/qcom,spmi-vadc.h> + +/ { + thermal-zones { + pmm8155au-1-thermal { + polling-delay-passive = <100>; + polling-delay = <0>; + + thermal-sensors = <&pmm8155au_1_temp>; + + trips { + trip0 { + temperature = <95000>; + hysteresis = <0>; + type = "passive"; + }; + + trip1 { + temperature = <115000>; + hysteresis = <0>; + type = "hot"; + }; + + trip2 { + temperature = <145000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + }; +}; + +&spmi_bus { + pmic@0 { + compatible = "qcom,pmm8155au", "qcom,spmi-pmic"; + reg = <0x0 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pon: power-on@800 { + compatible = "qcom,pm8916-pon"; + reg = <0x0800>; + pwrkey { + compatible = "qcom,pm8941-pwrkey"; + interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + bias-pull-up; + linux,code = <KEY_POWER>; + + status = "disabled"; + }; + }; + + pmm8155au_1_temp: temp-alarm@2400 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0x2400>; + interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; + io-channels = <&pmm8155au_1_adc ADC5_DIE_TEMP>; + io-channel-names = "thermal"; + #thermal-sensor-cells = <0>; + }; + + pmm8155au_1_adc: adc@3100 { + compatible = "qcom,spmi-adc5"; + reg = <0x3100>; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; + + ref-gnd@0 { + reg = <ADC5_REF_GND>; + qcom,pre-scaling = <1 1>; + label = "ref_gnd"; + }; + + vref-1p25@1 { + reg = <ADC5_1P25VREF>; + qcom,pre-scaling = <1 1>; + label = "vref_1p25"; + }; + + die-temp@6 { + reg = <ADC5_DIE_TEMP>; + qcom,pre-scaling = <1 1>; + label = "die_temp"; + }; + }; + + pmm8155au_1_adc_tm: adc-tm@3500 { + compatible = "qcom,spmi-adc-tm5"; + reg = <0x3500>; + interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>; + #thermal-sensor-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + pmm8155au_1_rtc: rtc@6000 { + compatible = "qcom,pm8941-rtc"; + reg = <0x6000>; + reg-names = "rtc", "alarm"; + interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; + + status = "disabled"; + }; + + pmm8155au_1_gpios: gpio@c000 { + compatible = "qcom,pmm8155au-gpio"; + reg = <0xc000>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + pmic@1 { + compatible = "qcom,pmm8155au", "qcom,spmi-pmic"; + reg = <0x1 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + }; +}; -- 2.31.1
next prev parent reply other threads:[~2021-06-15 7:50 UTC|newest] Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top 2021-06-15 7:45 [PATCH v2 00/10] arm64: dts: qcom: Add SA8155p-adp board DTS Bhupesh Sharma 2021-06-15 7:45 ` [PATCH v2 01/10] dt-bindings: qcom: rpmh-regulator: Add compatible for SA8155p-adp board pmic Bhupesh Sharma 2021-06-24 20:47 ` Rob Herring 2021-06-15 7:45 ` [PATCH v2 02/10] dt-bindings: pinctrl: qcom,pmic-gpio: Add compatible for SA8155p-adp Bhupesh Sharma 2021-06-15 21:00 ` Bjorn Andersson 2021-06-16 6:26 ` Bhupesh Sharma 2021-06-15 7:45 ` [PATCH v2 03/10] dt-bindings: arm: qcom: Add compatible for sm8150-mtp board Bhupesh Sharma 2021-06-15 7:45 ` [PATCH v2 04/10] dt-bindings: arm: qcom: Add compatible for SA8155p-adp board Bhupesh Sharma 2021-06-15 7:45 ` [PATCH v2 05/10] regulator: qcom-rpmh: Cleanup terminator line commas Bhupesh Sharma 2021-06-15 21:06 ` Bjorn Andersson 2021-06-15 7:45 ` [PATCH v2 06/10] regulator: qcom-rpmh: Add new regulator found on SA8155p adp board Bhupesh Sharma 2021-06-15 11:12 ` Mark Brown 2021-06-15 14:38 ` Bhupesh Sharma 2021-06-15 15:35 ` Mark Brown 2021-06-15 21:10 ` Bjorn Andersson 2021-06-15 7:45 ` [PATCH v2 07/10] pinctrl: qcom/pinctrl-spmi-gpio: Add compatible for pmic-gpio on SA8155p-adp Bhupesh Sharma 2021-06-15 21:07 ` Bjorn Andersson 2021-06-15 7:45 ` Bhupesh Sharma [this message] 2021-06-15 21:08 ` [PATCH v2 08/10] arm64: dts: qcom: pmm8155au_1: Add base dts file Bjorn Andersson 2021-06-15 7:45 ` [PATCH v2 09/10] arm64: dts: qcom: pmm8155au_2: " Bhupesh Sharma 2021-06-15 21:09 ` Bjorn Andersson 2021-06-15 7:45 ` [PATCH v2 10/10] arm64: dts: qcom: sa8155p-adp: " Bhupesh Sharma 2021-06-15 14:53 ` Konrad Dybcio 2021-06-15 17:00 ` Bhupesh Sharma 2021-06-15 21:13 ` Bjorn Andersson
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20210615074543.26700-9-bhupesh.sharma@linaro.org \ --to=bhupesh.sharma@linaro.org \ --cc=agross@kernel.org \ --cc=bhupesh.linux@gmail.com \ --cc=bjorn.andersson@linaro.org \ --cc=broonie@kernel.org \ --cc=devicetree@vger.kernel.org \ --cc=lgirdwood@gmail.com \ --cc=linus.walleij@linaro.org \ --cc=linux-arm-msm@vger.kernel.org \ --cc=linux-gpio@vger.kernel.org \ --cc=linux-kernel@vger.kernel.org \ --cc=robh+dt@kernel.org \ --cc=vkoul@kernel.org \ --subject='Re: [PATCH v2 08/10] arm64: dts: qcom: pmm8155au_1: Add base dts file' \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: link
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).