[PATCH v5 0/6] clk: qcom: use power-domain for sm8250's clock controllers

[PATCH v5 0/6] clk: qcom: use power-domain for sm8250's clock controllers

[Dmitry Baryshkov]

On SM8250 both the display and video clock controllers are powered up by
the MMCX power domain. Handle this by linking clock controllers to the
proper power domain, and using runtime power management to enable and
disable the MMCX power domain.

Dependencies:
- https://lore.kernel.org/linux-arm-msm/20210703005416.2668319-1-bjorn.andersson@linaro.org/
  (pending)

Changes since v4:
 - Dropped pm_runtime handling from drivers/clk/qcom/common.c Moved the
   code into dispcc-sm8250.c and videocc-sm8250.c

Changes since v3:
 - Wrap gdsc_enable/gdsc_disable into pm_runtime_get/put calls rather
   than calling pm_runtime_get in gdsc_enabled and _put in gdsc_disable
 - Squash gdsc patches together to remove possible dependencies between
   two patches.

Changes since v2:
 - Move pm_runtime calls from generic genpd code to the gdsc code for
   now (as suggested by Ulf & Bjorn)

Changes since v1:
 - Rebase on top of Bjorn's patches, removing the need for setting
   performance state directly.
 - Move runtime PM calls from GDSC code to generic genpd code.
 - Always call pm_runtime_enable in the Qualcomm generic clock
   controller code.
 - Register GDSC power domains as subdomains of the domain powering the
   clock controller if there is one.

----------------------------------------------------------------
Dmitry Baryshkov (9):
      dt-bindings: clock: qcom,dispcc-sm8x50: add mmcx power domain
      dt-bindings: clock: qcom,videocc: add mmcx power domain
      PM: runtime: add devm_pm_runtime_enable helper
      clk: qcom: dispcc-sm8250: use runtime PM for the clock controller
      clk: qcom: videocc-sm8250: use runtime PM for the clock controller
      clk: qcom: gdsc: enable optional power domain support
      arm64: dts: qcom: sm8250: remove mmcx regulator
      clk: qcom: dispcc-sm8250: stop using mmcx regulator
      clk: qcom: videocc-sm8250: stop using mmcx regulator

 .../bindings/clock/qcom,dispcc-sm8x50.yaml         |  7 +++
 .../devicetree/bindings/clock/qcom,videocc.yaml    |  7 +++
 arch/arm64/boot/dts/qcom/sm8250.dtsi               | 11 +---
 drivers/base/power/runtime.c                       | 17 +++++++
 drivers/clk/qcom/dispcc-sm8250.c                   | 21 ++++++--
 drivers/clk/qcom/gdsc.c                            | 59 ++++++++++++++++++++--
 drivers/clk/qcom/gdsc.h                            |  2 +
 drivers/clk/qcom/videocc-sm8250.c                  | 24 ++++++---
 include/linux/pm_runtime.h                         |  4 ++
 9 files changed, 131 insertions(+), 21 deletions(-)

[PATCH v5 1/9] dt-bindings: clock: qcom,dispcc-sm8x50: add mmcx power domain

[Dmitry Baryshkov]

On sm8250 dispcc requires MMCX power domain to be powered up before
clock controller's registers become available. For now sm8250 was using
external regulator driven by the power domain to describe this
relationship. Switch into specifying power-domain and required opp-state
directly.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../devicetree/bindings/clock/qcom,dispcc-sm8x50.yaml      | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/clock/qcom,dispcc-sm8x50.yaml b/Documentation/devicetree/bindings/clock/qcom,dispcc-sm8x50.yaml
index 6667261dc665..6b3380cf1a10 100644
--- a/Documentation/devicetree/bindings/clock/qcom,dispcc-sm8x50.yaml
+++ b/Documentation/devicetree/bindings/clock/qcom,dispcc-sm8x50.yaml
@@ -56,6 +56,11 @@ properties:
   reg:
     maxItems: 1
 
+  power-domains:
+    description:
+      A phandle and PM domain specifier for the MMCX power domain.
+    maxItems: 1
+
 required:
   - compatible
   - reg
@@ -70,6 +75,7 @@ additionalProperties: false
 examples:
   - |
     #include <dt-bindings/clock/qcom,rpmh.h>
+    #include <dt-bindings/power/qcom-rpmpd.h>
     clock-controller@af00000 {
       compatible = "qcom,sm8250-dispcc";
       reg = <0x0af00000 0x10000>;
@@ -90,5 +96,6 @@ examples:
       #clock-cells = <1>;
       #reset-cells = <1>;
       #power-domain-cells = <1>;
+      power-domains = <&rpmhpd SM8250_MMCX>;
     };
 ...
-- 
2.30.2

[PATCH v5 2/9] dt-bindings: clock: qcom,videocc: add mmcx power domain

[Dmitry Baryshkov]

On sm8250 videocc requires MMCX power domain to be powered up before
clock controller's registers become available. For now sm8250 was using
external regulator driven by the power domain to describe this
relationship. Switch into specifying power-domain and required opp-state
directly.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/clock/qcom,videocc.yaml | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/clock/qcom,videocc.yaml b/Documentation/devicetree/bindings/clock/qcom,videocc.yaml
index 567202942b88..db4ada6acf27 100644
--- a/Documentation/devicetree/bindings/clock/qcom,videocc.yaml
+++ b/Documentation/devicetree/bindings/clock/qcom,videocc.yaml
@@ -47,6 +47,11 @@ properties:
   reg:
     maxItems: 1
 
+  power-domains:
+    description:
+      A phandle and PM domain specifier for the MMCX power domain.
+    maxItems: 1
+
 required:
   - compatible
   - reg
@@ -61,6 +66,7 @@ additionalProperties: false
 examples:
   - |
     #include <dt-bindings/clock/qcom,rpmh.h>
+    #include <dt-bindings/power/qcom-rpmpd.h>
     clock-controller@ab00000 {
       compatible = "qcom,sdm845-videocc";
       reg = <0x0ab00000 0x10000>;
@@ -69,5 +75,6 @@ examples:
       #clock-cells = <1>;
       #reset-cells = <1>;
       #power-domain-cells = <1>;
+      power-domains = <&rpmhpd SM8250_MMCX>;
     };
 ...
-- 
2.30.2

[PATCH v5 3/9] PM: runtime: add devm_pm_runtime_enable helper

[Dmitry Baryshkov]

Add helper function handling typical driver action: call
pm_runtime_enable at the probe() time and disable it during remove().

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 drivers/base/power/runtime.c | 17 +++++++++++++++++
 include/linux/pm_runtime.h   |  4 ++++
 2 files changed, 21 insertions(+)

diff --git a/drivers/base/power/runtime.c b/drivers/base/power/runtime.c
index 8a66eaf731e4..ec94049442b9 100644
--- a/drivers/base/power/runtime.c
+++ b/drivers/base/power/runtime.c
@@ -1447,6 +1447,23 @@ void pm_runtime_enable(struct device *dev)
 }
 EXPORT_SYMBOL_GPL(pm_runtime_enable);
 
+static void pm_runtime_disable_action(void *data)
+{
+	pm_runtime_disable(data);
+}
+
+/**
+ * devm_pm_runtime_enable - devres-enabled version of pm_runtime_enable.
+ * @dev: Device to handle.
+ */
+int devm_pm_runtime_enable(struct device *dev)
+{
+	pm_runtime_enable(dev);
+
+	return devm_add_action_or_reset(dev, pm_runtime_disable_action, dev);
+}
+EXPORT_SYMBOL_GPL(devm_pm_runtime_enable);
+
 /**
  * pm_runtime_forbid - Block runtime PM of a device.
  * @dev: Device to handle.
diff --git a/include/linux/pm_runtime.h b/include/linux/pm_runtime.h
index aab8b35e9f8a..222da43b7096 100644
--- a/include/linux/pm_runtime.h
+++ b/include/linux/pm_runtime.h
@@ -59,6 +59,8 @@ extern void pm_runtime_put_suppliers(struct device *dev);
 extern void pm_runtime_new_link(struct device *dev);
 extern void pm_runtime_drop_link(struct device_link *link);
 
+extern int devm_pm_runtime_enable(struct device *dev);
+
 /**
  * pm_runtime_get_if_in_use - Conditionally bump up runtime PM usage counter.
  * @dev: Target device.
@@ -253,6 +255,8 @@ static inline void __pm_runtime_disable(struct device *dev, bool c) {}
 static inline void pm_runtime_allow(struct device *dev) {}
 static inline void pm_runtime_forbid(struct device *dev) {}
 
+static inline int devm_pm_runtime_enable(struct device *dev) { return 0; }
+
 static inline void pm_suspend_ignore_children(struct device *dev, bool enable) {}
 static inline void pm_runtime_get_noresume(struct device *dev) {}
 static inline void pm_runtime_put_noidle(struct device *dev) {}
-- 
2.30.2

[PATCH v5 4/9] clk: qcom: dispcc-sm8250: use runtime PM for the clock controller

[Dmitry Baryshkov]

On sm8250 dispcc and videocc registers are powered up by the MMCX power
domain. Use runtime PM calls to make sure that required power domain is
powered on while we access clock controller's registers.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 drivers/clk/qcom/dispcc-sm8250.c | 20 ++++++++++++++++++--
 1 file changed, 18 insertions(+), 2 deletions(-)

diff --git a/drivers/clk/qcom/dispcc-sm8250.c b/drivers/clk/qcom/dispcc-sm8250.c
index 601c7c0ba483..0625fea6d7ba 100644
--- a/drivers/clk/qcom/dispcc-sm8250.c
+++ b/drivers/clk/qcom/dispcc-sm8250.c
@@ -6,6 +6,7 @@
 #include <linux/clk-provider.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
 #include <linux/regmap.h>
 #include <linux/reset-controller.h>
 
@@ -1229,10 +1230,21 @@ MODULE_DEVICE_TABLE(of, disp_cc_sm8250_match_table);
 static int disp_cc_sm8250_probe(struct platform_device *pdev)
 {
 	struct regmap *regmap;
+	int ret;
+
+	ret = devm_pm_runtime_enable(&pdev->dev);
+	if (ret)
+		return ret;
+
+	ret = pm_runtime_resume_and_get(&pdev->dev);
+	if (ret)
+		return ret;
 
 	regmap = qcom_cc_map(pdev, &disp_cc_sm8250_desc);
-	if (IS_ERR(regmap))
+	if (IS_ERR(regmap)) {
+		pm_runtime_put(&pdev->dev);
 		return PTR_ERR(regmap);
+	}
 
 	/* note: trion == lucid, except for the prepare() op */
 	BUILD_BUG_ON(CLK_ALPHA_PLL_TYPE_TRION != CLK_ALPHA_PLL_TYPE_LUCID);
@@ -1257,7 +1269,11 @@ static int disp_cc_sm8250_probe(struct platform_device *pdev)
 	/* DISP_CC_XO_CLK always-on */
 	regmap_update_bits(regmap, 0x605c, BIT(0), BIT(0));
 
-	return qcom_cc_really_probe(pdev, &disp_cc_sm8250_desc, regmap);
+	ret = qcom_cc_really_probe(pdev, &disp_cc_sm8250_desc, regmap);
+
+	pm_runtime_put(&pdev->dev);
+
+	return ret;
 }
 
 static struct platform_driver disp_cc_sm8250_driver = {
-- 
2.30.2

[PATCH v5 5/9] clk: qcom: videocc-sm8250: use runtime PM for the clock controller

[Dmitry Baryshkov]

On sm8250 dispcc and videocc registers are powered up by the MMCX power
domain. Use runtime PM calls to make sure that required power domain is
powered on while we access clock controller's registers.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 drivers/clk/qcom/videocc-sm8250.c | 20 ++++++++++++++++++--
 1 file changed, 18 insertions(+), 2 deletions(-)

diff --git a/drivers/clk/qcom/videocc-sm8250.c b/drivers/clk/qcom/videocc-sm8250.c
index 7b435a1c2c4b..d996b76f4e30 100644
--- a/drivers/clk/qcom/videocc-sm8250.c
+++ b/drivers/clk/qcom/videocc-sm8250.c
@@ -6,6 +6,7 @@
 #include <linux/clk-provider.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
 #include <linux/regmap.h>
 
 #include <dt-bindings/clock/qcom,videocc-sm8250.h>
@@ -367,10 +368,21 @@ MODULE_DEVICE_TABLE(of, video_cc_sm8250_match_table);
 static int video_cc_sm8250_probe(struct platform_device *pdev)
 {
 	struct regmap *regmap;
+	int ret;
+
+	ret = devm_pm_runtime_enable(&pdev->dev);
+	if (ret)
+		return ret;
+
+	ret = pm_runtime_resume_and_get(&pdev->dev);
+	if (ret)
+		return ret;
 
 	regmap = qcom_cc_map(pdev, &video_cc_sm8250_desc);
-	if (IS_ERR(regmap))
+	if (IS_ERR(regmap)) {
+		pm_runtime_put(&pdev->dev);
 		return PTR_ERR(regmap);
+	}
 
 	clk_lucid_pll_configure(&video_pll0, regmap, &video_pll0_config);
 	clk_lucid_pll_configure(&video_pll1, regmap, &video_pll1_config);
@@ -379,7 +391,11 @@ static int video_cc_sm8250_probe(struct platform_device *pdev)
 	regmap_update_bits(regmap, 0xe58, BIT(0), BIT(0));
 	regmap_update_bits(regmap, 0xeec, BIT(0), BIT(0));
 
-	return qcom_cc_really_probe(pdev, &video_cc_sm8250_desc, regmap);
+	ret = qcom_cc_really_probe(pdev, &video_cc_sm8250_desc, regmap);
+
+	pm_runtime_put(&pdev->dev);
+
+	return ret;
 }
 
 static struct platform_driver video_cc_sm8250_driver = {
-- 
2.30.2

[PATCH v5 6/9] clk: qcom: gdsc: enable optional power domain support

[Dmitry Baryshkov]

On sm8250 dispcc and videocc registers are powered up by the MMCX power
domain. Currently we use a regulator to enable this domain on demand,
however this has some consequences, as genpd code is not reentrant.

Make gdsc code also use pm_runtime calls to ensure that registers are
accessible during the gdsc_enable/gdsc_disable operations.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 drivers/clk/qcom/gdsc.c | 59 ++++++++++++++++++++++++++++++++++++++---
 drivers/clk/qcom/gdsc.h |  2 ++
 2 files changed, 58 insertions(+), 3 deletions(-)

diff --git a/drivers/clk/qcom/gdsc.c b/drivers/clk/qcom/gdsc.c
index 51ed640e527b..a0781d7284cc 100644
--- a/drivers/clk/qcom/gdsc.c
+++ b/drivers/clk/qcom/gdsc.c
@@ -11,6 +11,7 @@
 #include <linux/kernel.h>
 #include <linux/ktime.h>
 #include <linux/pm_domain.h>
+#include <linux/pm_runtime.h>
 #include <linux/regmap.h>
 #include <linux/regulator/consumer.h>
 #include <linux/reset-controller.h>
@@ -50,6 +51,22 @@ enum gdsc_status {
 	GDSC_ON
 };
 
+static int gdsc_pm_runtime_get(struct gdsc *sc)
+{
+	if (!sc->dev)
+		return 0;
+
+	return pm_runtime_resume_and_get(sc->dev);
+}
+
+static int gdsc_pm_runtime_put(struct gdsc *sc)
+{
+	if (!sc->dev)
+		return 0;
+
+	return pm_runtime_put_sync(sc->dev);
+}
+
 /* Returns 1 if GDSC status is status, 0 if not, and < 0 on error */
 static int gdsc_check_status(struct gdsc *sc, enum gdsc_status status)
 {
@@ -232,9 +249,8 @@ static void gdsc_retain_ff_on(struct gdsc *sc)
 	regmap_update_bits(sc->regmap, sc->gdscr, mask, mask);
 }
 
-static int gdsc_enable(struct generic_pm_domain *domain)
+static int _gdsc_enable(struct gdsc *sc)
 {
-	struct gdsc *sc = domain_to_gdsc(domain);
 	int ret;
 
 	if (sc->pwrsts == PWRSTS_ON)
@@ -290,11 +306,26 @@ static int gdsc_enable(struct generic_pm_domain *domain)
 	return 0;
 }
 
-static int gdsc_disable(struct generic_pm_domain *domain)
+static int gdsc_enable(struct generic_pm_domain *domain)
 {
 	struct gdsc *sc = domain_to_gdsc(domain);
 	int ret;
 
+	ret = gdsc_pm_runtime_get(sc);
+	if (ret)
+		return ret;
+
+	ret = _gdsc_enable(sc);
+
+	gdsc_pm_runtime_put(sc);
+
+	return ret;
+}
+
+static int _gdsc_disable(struct gdsc *sc)
+{
+	int ret;
+
 	if (sc->pwrsts == PWRSTS_ON)
 		return gdsc_assert_reset(sc);
 
@@ -329,6 +360,22 @@ static int gdsc_disable(struct generic_pm_domain *domain)
 	return 0;
 }
 
+static int gdsc_disable(struct generic_pm_domain *domain)
+{
+	struct gdsc *sc = domain_to_gdsc(domain);
+	int ret;
+
+	ret = gdsc_pm_runtime_get(sc);
+	if (ret)
+		return ret;
+
+	ret = _gdsc_disable(sc);
+
+	gdsc_pm_runtime_put(sc);
+
+	return ret;
+}
+
 static int gdsc_init(struct gdsc *sc)
 {
 	u32 mask, val;
@@ -425,6 +472,8 @@ int gdsc_register(struct gdsc_desc *desc,
 	for (i = 0; i < num; i++) {
 		if (!scs[i])
 			continue;
+		if (pm_runtime_enabled(dev))
+			scs[i]->dev = dev;
 		scs[i]->regmap = regmap;
 		scs[i]->rcdev = rcdev;
 		ret = gdsc_init(scs[i]);
@@ -439,6 +488,8 @@ int gdsc_register(struct gdsc_desc *desc,
 			continue;
 		if (scs[i]->parent)
 			pm_genpd_add_subdomain(scs[i]->parent, &scs[i]->pd);
+		else if (!IS_ERR_OR_NULL(dev->pm_domain))
+			pm_genpd_add_subdomain(pd_to_genpd(dev->pm_domain), &scs[i]->pd);
 	}
 
 	return of_genpd_add_provider_onecell(dev->of_node, data);
@@ -457,6 +508,8 @@ void gdsc_unregister(struct gdsc_desc *desc)
 			continue;
 		if (scs[i]->parent)
 			pm_genpd_remove_subdomain(scs[i]->parent, &scs[i]->pd);
+		else if (!IS_ERR_OR_NULL(dev->pm_domain))
+			pm_genpd_remove_subdomain(pd_to_genpd(dev->pm_domain), &scs[i]->pd);
 	}
 	of_genpd_del_provider(dev->of_node);
 }
diff --git a/drivers/clk/qcom/gdsc.h b/drivers/clk/qcom/gdsc.h
index 5bb396b344d1..702d47a87af6 100644
--- a/drivers/clk/qcom/gdsc.h
+++ b/drivers/clk/qcom/gdsc.h
@@ -25,6 +25,7 @@ struct reset_controller_dev;
  * @resets: ids of resets associated with this gdsc
  * @reset_count: number of @resets
  * @rcdev: reset controller
+ * @dev: the device holding the GDSC, used for pm_runtime calls
  */
 struct gdsc {
 	struct generic_pm_domain	pd;
@@ -58,6 +59,7 @@ struct gdsc {
 
 	const char 			*supply;
 	struct regulator		*rsupply;
+	struct device 			*dev;
 };
 
 struct gdsc_desc {
-- 
2.30.2

[PATCH v5 7/9] arm64: dts: qcom: sm8250: remove mmcx regulator

[Dmitry Baryshkov]

Switch dispcc and videocc into using MMCX domain directly. Drop the now
unused mmcx regulator.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8250.dtsi | 11 ++---------
 1 file changed, 2 insertions(+), 9 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index 4798368b02ef..bce5e9a9dd84 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -273,13 +273,6 @@ memory@80000000 {
 		reg = <0x0 0x80000000 0x0 0x0>;
 	};
 
-	mmcx_reg: mmcx-reg {
-		compatible = "regulator-fixed-domain";
-		power-domains = <&rpmhpd SM8250_MMCX>;
-		required-opps = <&rpmhpd_opp_low_svs>;
-		regulator-name = "MMCX";
-	};
-
 	pmu {
 		compatible = "arm,armv8-pmuv3";
 		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW>;
@@ -2451,7 +2444,7 @@ videocc: clock-controller@abf0000 {
 			clocks = <&gcc GCC_VIDEO_AHB_CLK>,
 				 <&rpmhcc RPMH_CXO_CLK>,
 				 <&rpmhcc RPMH_CXO_CLK_A>;
-			mmcx-supply = <&mmcx_reg>;
+			power-domains = <&rpmhpd SM8250_MMCX>;
 			clock-names = "iface", "bi_tcxo", "bi_tcxo_ao";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -2720,7 +2713,7 @@ opp-358000000 {
 		dispcc: clock-controller@af00000 {
 			compatible = "qcom,sm8250-dispcc";
 			reg = <0 0x0af00000 0 0x10000>;
-			mmcx-supply = <&mmcx_reg>;
+			power-domains = <&rpmhpd SM8250_MMCX>;
 			clocks = <&rpmhcc RPMH_CXO_CLK>,
 				 <&dsi0_phy 0>,
 				 <&dsi0_phy 1>,
-- 
2.30.2

[PATCH v5 8/9] clk: qcom: dispcc-sm8250: stop using mmcx regulator

[Dmitry Baryshkov]

Now as the common qcom clock controller code has been taught about power
domains, stop mentioning mmcx supply as a way to power up the clock
controller's gdsc.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
 drivers/clk/qcom/dispcc-sm8250.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/drivers/clk/qcom/dispcc-sm8250.c b/drivers/clk/qcom/dispcc-sm8250.c
index 0625fea6d7ba..372d3a8f38cf 100644
--- a/drivers/clk/qcom/dispcc-sm8250.c
+++ b/drivers/clk/qcom/dispcc-sm8250.c
@@ -1129,7 +1129,6 @@ static struct gdsc mdss_gdsc = {
 	},
 	.pwrsts = PWRSTS_OFF_ON,
 	.flags = HW_CTRL,
-	.supply = "mmcx",
 };
 
 static struct clk_regmap *disp_cc_sm8250_clocks[] = {
-- 
2.30.2

[PATCH v5 9/9] clk: qcom: videocc-sm8250: stop using mmcx regulator

[Dmitry Baryshkov]

Now as the common qcom clock controller code has been taught about power
domains, stop mentioning mmcx supply as a way to power up the clock
controller's gdscs.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
 drivers/clk/qcom/videocc-sm8250.c | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/drivers/clk/qcom/videocc-sm8250.c b/drivers/clk/qcom/videocc-sm8250.c
index d996b76f4e30..ad46c4014a40 100644
--- a/drivers/clk/qcom/videocc-sm8250.c
+++ b/drivers/clk/qcom/videocc-sm8250.c
@@ -277,7 +277,6 @@ static struct gdsc mvs0c_gdsc = {
 	},
 	.flags = 0,
 	.pwrsts = PWRSTS_OFF_ON,
-	.supply = "mmcx",
 };
 
 static struct gdsc mvs1c_gdsc = {
@@ -287,7 +286,6 @@ static struct gdsc mvs1c_gdsc = {
 	},
 	.flags = 0,
 	.pwrsts = PWRSTS_OFF_ON,
-	.supply = "mmcx",
 };
 
 static struct gdsc mvs0_gdsc = {
@@ -297,7 +295,6 @@ static struct gdsc mvs0_gdsc = {
 	},
 	.flags = HW_CTRL,
 	.pwrsts = PWRSTS_OFF_ON,
-	.supply = "mmcx",
 };
 
 static struct gdsc mvs1_gdsc = {
@@ -307,7 +304,6 @@ static struct gdsc mvs1_gdsc = {
 	},
 	.flags = HW_CTRL,
 	.pwrsts = PWRSTS_OFF_ON,
-	.supply = "mmcx",
 };
 
 static struct clk_regmap *video_cc_sm8250_clocks[] = {
-- 
2.30.2

Re: [PATCH v5 3/9] PM: runtime: add devm_pm_runtime_enable helper

[Ulf Hansson]

On Sun, 18 Jul 2021 at 12:49, Dmitry Baryshkov
<dmitry.baryshkov@linaro.org> wrote:
>
> Add helper function handling typical driver action: call
> pm_runtime_enable at the probe() time and disable it during remove().
>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
>  drivers/base/power/runtime.c | 17 +++++++++++++++++
>  include/linux/pm_runtime.h   |  4 ++++
>  2 files changed, 21 insertions(+)

First, this needs to be sent to the correct maintainers (Rafael) and
also the mailing list (linux-pm).

Second, to not stall the series by $subject patch as it will likely
need to be funneled through Rafael's tree, perhaps it's just better to
do the "open coding" in the qcom drivers for now.

Kind regards
Uffe

>
> diff --git a/drivers/base/power/runtime.c b/drivers/base/power/runtime.c
> index 8a66eaf731e4..ec94049442b9 100644
> --- a/drivers/base/power/runtime.c
> +++ b/drivers/base/power/runtime.c
> @@ -1447,6 +1447,23 @@ void pm_runtime_enable(struct device *dev)
>  }
>  EXPORT_SYMBOL_GPL(pm_runtime_enable);
>
> +static void pm_runtime_disable_action(void *data)
> +{
> +       pm_runtime_disable(data);
> +}
> +
> +/**
> + * devm_pm_runtime_enable - devres-enabled version of pm_runtime_enable.
> + * @dev: Device to handle.
> + */
> +int devm_pm_runtime_enable(struct device *dev)
> +{
> +       pm_runtime_enable(dev);
> +
> +       return devm_add_action_or_reset(dev, pm_runtime_disable_action, dev);
> +}
> +EXPORT_SYMBOL_GPL(devm_pm_runtime_enable);
> +
>  /**
>   * pm_runtime_forbid - Block runtime PM of a device.
>   * @dev: Device to handle.
> diff --git a/include/linux/pm_runtime.h b/include/linux/pm_runtime.h
> index aab8b35e9f8a..222da43b7096 100644
> --- a/include/linux/pm_runtime.h
> +++ b/include/linux/pm_runtime.h
> @@ -59,6 +59,8 @@ extern void pm_runtime_put_suppliers(struct device *dev);
>  extern void pm_runtime_new_link(struct device *dev);
>  extern void pm_runtime_drop_link(struct device_link *link);
>
> +extern int devm_pm_runtime_enable(struct device *dev);
> +
>  /**
>   * pm_runtime_get_if_in_use - Conditionally bump up runtime PM usage counter.
>   * @dev: Target device.
> @@ -253,6 +255,8 @@ static inline void __pm_runtime_disable(struct device *dev, bool c) {}
>  static inline void pm_runtime_allow(struct device *dev) {}
>  static inline void pm_runtime_forbid(struct device *dev) {}
>
> +static inline int devm_pm_runtime_enable(struct device *dev) { return 0; }
> +
>  static inline void pm_suspend_ignore_children(struct device *dev, bool enable) {}
>  static inline void pm_runtime_get_noresume(struct device *dev) {}
>  static inline void pm_runtime_put_noidle(struct device *dev) {}
> --
> 2.30.2
>

Re: [PATCH v5 3/9] PM: runtime: add devm_pm_runtime_enable helper

[Dmitry Baryshkov]

On 22/07/2021 13:26, Ulf Hansson wrote:
> On Sun, 18 Jul 2021 at 12:49, Dmitry Baryshkov
> <dmitry.baryshkov@linaro.org> wrote:
>>
>> Add helper function handling typical driver action: call
>> pm_runtime_enable at the probe() time and disable it during remove().
>>
>> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
>> ---
>>   drivers/base/power/runtime.c | 17 +++++++++++++++++
>>   include/linux/pm_runtime.h   |  4 ++++
>>   2 files changed, 21 insertions(+)
> 
> First, this needs to be sent to the correct maintainers (Rafael) and
> also the mailing list (linux-pm).
> 
> Second, to not stall the series by $subject patch as it will likely
> need to be funneled through Rafael's tree, perhaps it's just better to
> do the "open coding" in the qcom drivers for now.

Ack

> 
> Kind regards
> Uffe
> 
>>
>> diff --git a/drivers/base/power/runtime.c b/drivers/base/power/runtime.c
>> index 8a66eaf731e4..ec94049442b9 100644
>> --- a/drivers/base/power/runtime.c
>> +++ b/drivers/base/power/runtime.c
>> @@ -1447,6 +1447,23 @@ void pm_runtime_enable(struct device *dev)
>>   }
>>   EXPORT_SYMBOL_GPL(pm_runtime_enable);
>>
>> +static void pm_runtime_disable_action(void *data)
>> +{
>> +       pm_runtime_disable(data);
>> +}
>> +
>> +/**
>> + * devm_pm_runtime_enable - devres-enabled version of pm_runtime_enable.
>> + * @dev: Device to handle.
>> + */
>> +int devm_pm_runtime_enable(struct device *dev)
>> +{
>> +       pm_runtime_enable(dev);
>> +
>> +       return devm_add_action_or_reset(dev, pm_runtime_disable_action, dev);
>> +}
>> +EXPORT_SYMBOL_GPL(devm_pm_runtime_enable);
>> +
>>   /**
>>    * pm_runtime_forbid - Block runtime PM of a device.
>>    * @dev: Device to handle.
>> diff --git a/include/linux/pm_runtime.h b/include/linux/pm_runtime.h
>> index aab8b35e9f8a..222da43b7096 100644
>> --- a/include/linux/pm_runtime.h
>> +++ b/include/linux/pm_runtime.h
>> @@ -59,6 +59,8 @@ extern void pm_runtime_put_suppliers(struct device *dev);
>>   extern void pm_runtime_new_link(struct device *dev);
>>   extern void pm_runtime_drop_link(struct device_link *link);
>>
>> +extern int devm_pm_runtime_enable(struct device *dev);
>> +
>>   /**
>>    * pm_runtime_get_if_in_use - Conditionally bump up runtime PM usage counter.
>>    * @dev: Target device.
>> @@ -253,6 +255,8 @@ static inline void __pm_runtime_disable(struct device *dev, bool c) {}
>>   static inline void pm_runtime_allow(struct device *dev) {}
>>   static inline void pm_runtime_forbid(struct device *dev) {}
>>
>> +static inline int devm_pm_runtime_enable(struct device *dev) { return 0; }
>> +
>>   static inline void pm_suspend_ignore_children(struct device *dev, bool enable) {}
>>   static inline void pm_runtime_get_noresume(struct device *dev) {}
>>   static inline void pm_runtime_put_noidle(struct device *dev) {}
>> --
>> 2.30.2
>>


-- 
With best wishes
Dmitry