linux-arm-msm.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
To: Andy Gross <agross@kernel.org>,
	Bjorn Andersson <bjorn.andersson@linaro.org>,
	Ulf Hansson <ulf.hansson@linaro.org>,
	Marcel Holtmann <marcel@holtmann.org>,
	Johan Hedberg <johan.hedberg@gmail.com>,
	Luiz Augusto von Dentz <luiz.dentz@gmail.com>,
	Kalle Valo <kvalo@codeaurora.org>,
	"David S. Miller" <davem@davemloft.net>,
	Jakub Kicinski <kuba@kernel.org>,
	Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: linux-arm-msm@vger.kernel.org, linux-mmc@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-bluetooth@vger.kernel.org,
	ath10k@lists.infradead.org, linux-wireless@vger.kernel.org,
	netdev@vger.kernel.org
Subject: [PATCH v1 06/15] pwrseq: add support for QCA BT+WiFi power sequencer
Date: Wed,  6 Oct 2021 06:53:58 +0300	[thread overview]
Message-ID: <20211006035407.1147909-7-dmitry.baryshkov@linaro.org> (raw)
In-Reply-To: <20211006035407.1147909-1-dmitry.baryshkov@linaro.org>

Add support for power sequencer used in the Qualcomm BT+WiFi SoCs. They
require several external volate regulators and some of them use separate
BT and WiFi enable GPIO pins. This code is mostly extracted from the
hci_qca.c bluetooth driver and ath10k WiFi driver. Instead of having
each of them manage pins, different requirements, regulator types, move
this knowledge to the common power sequencer driver. Currently original
drivers are not stripped from the regulator code, this will be done
later (to keep compatibility with the old device trees).

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 drivers/power/pwrseq/Kconfig      |  14 ++
 drivers/power/pwrseq/Makefile     |   1 +
 drivers/power/pwrseq/pwrseq_qca.c | 373 ++++++++++++++++++++++++++++++
 3 files changed, 388 insertions(+)
 create mode 100644 drivers/power/pwrseq/pwrseq_qca.c

diff --git a/drivers/power/pwrseq/Kconfig b/drivers/power/pwrseq/Kconfig
index 1985f13d9193..7983e37c7855 100644
--- a/drivers/power/pwrseq/Kconfig
+++ b/drivers/power/pwrseq/Kconfig
@@ -22,6 +22,20 @@ config PWRSEQ_EMMC
 	  This driver can also be built as a module. If so, the module
 	  will be called pwrseq_emmc.
 
+config PWRSEQ_QCA
+	tristate "Power Sequencer for Qualcomm WiFi + BT SoCs"
+	depends on OF
+	help
+	  If you say yes to this option, support will be included for Qualcomm
+	  WCN399x,QCA639x,QCA67xx families of hybrid WiFi and Bluetooth SoCs.
+	  Note, this driver supports only power control for these SoC, you
+	  still have to enable individual Bluetooth and WiFi drivers. This
+	  driver is only necessary on ARM platforms with these chips. PCIe
+	  cards handle power sequencing on their own.
+
+	  Say M here if you want to include support for Qualcomm WiFi+BT SoCs
+	  as a module. This will build a module called "pwrseq_qca".
+
 config PWRSEQ_SD8787
 	tristate "HW reset support for SD8787 BT + Wifi module"
 	depends on OF
diff --git a/drivers/power/pwrseq/Makefile b/drivers/power/pwrseq/Makefile
index 6f359d228843..556bf5582d47 100644
--- a/drivers/power/pwrseq/Makefile
+++ b/drivers/power/pwrseq/Makefile
@@ -6,5 +6,6 @@
 obj-$(CONFIG_PWRSEQ) += core.o
 
 obj-$(CONFIG_PWRSEQ_EMMC)	+= pwrseq_emmc.o
+obj-$(CONFIG_PWRSEQ_QCA)	+= pwrseq_qca.o
 obj-$(CONFIG_PWRSEQ_SD8787)	+= pwrseq_sd8787.o
 obj-$(CONFIG_PWRSEQ_SIMPLE)	+= pwrseq_simple.o
diff --git a/drivers/power/pwrseq/pwrseq_qca.c b/drivers/power/pwrseq/pwrseq_qca.c
new file mode 100644
index 000000000000..c15508cc80d2
--- /dev/null
+++ b/drivers/power/pwrseq/pwrseq_qca.c
@@ -0,0 +1,373 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2021, Linaro Ltd.
+ *
+ * Author: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
+ *
+ * Power Sequencer for Qualcomm WiFi + BT SoCs
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+#include <linux/pwrseq/driver.h>
+#include <linux/regulator/consumer.h>
+
+/* susclk rate */
+#define SUSCLK_RATE_32KHZ	32768
+
+/*
+ * Voltage regulator information required for configuring the
+ * QCA WiFi+Bluetooth chipset
+ */
+struct qca_vreg {
+	const char *name;
+	unsigned int load_uA;
+};
+
+struct qca_device_data {
+	bool has_enable_gpios;
+
+	/*
+	 * VDDIO has to be enabled before the rest of regulators, so we treat
+	 * it separately
+	 */
+	struct qca_vreg vddio;
+
+	size_t num_vregs;
+	struct qca_vreg vregs[];
+};
+
+struct pwrseq_qca_common {
+	struct gpio_desc *sw_ctrl;
+	struct clk *susclk;
+
+	/*
+	 * Again vddio is separate so that it can be enabled before enabling
+	 * other regulators.
+	 */
+	struct regulator *vddio;
+	int num_vregs;
+	struct regulator_bulk_data vregs[];
+};
+
+struct pwrseq_qca_one {
+	struct pwrseq_qca_common *common;
+	struct gpio_desc *enable;
+};
+
+#define PWRSEQ_QCA_WIFI 0
+#define PWRSEQ_QCA_BT 1
+
+#define PWRSEQ_QCA_MAX 2
+
+struct pwrseq_qca {
+	struct pwrseq_qca_one pwrseq_qcas[PWRSEQ_QCA_MAX];
+	struct pwrseq_qca_common common;
+};
+
+static int pwrseq_qca_pre_power_on(struct pwrseq *pwrseq)
+{
+	struct pwrseq_qca_one *qca_one = pwrseq_get_drvdata(pwrseq);
+
+	if (qca_one->enable) {
+		gpiod_set_value_cansleep(qca_one->enable, 0);
+		msleep(50);
+	}
+
+	return 0;
+}
+
+static int pwrseq_qca_power_on(struct pwrseq *pwrseq)
+{
+	struct pwrseq_qca_one *qca_one = pwrseq_get_drvdata(pwrseq);
+	int ret;
+
+	if (qca_one->common->vddio) {
+		ret = regulator_enable(qca_one->common->vddio);
+		if (ret)
+			return ret;
+	}
+
+	ret = regulator_bulk_enable(qca_one->common->num_vregs, qca_one->common->vregs);
+	if (ret)
+		goto err_bulk;
+
+	ret = clk_prepare_enable(qca_one->common->susclk);
+	if (ret)
+		goto err_clk;
+
+	if (qca_one->enable) {
+		gpiod_set_value_cansleep(qca_one->enable, 1);
+		msleep(150);
+	}
+
+	if (qca_one->common->sw_ctrl) {
+		bool sw_ctrl_state = gpiod_get_value_cansleep(qca_one->common->sw_ctrl);
+		dev_dbg(&pwrseq->dev, "SW_CTRL is %d", sw_ctrl_state);
+	}
+
+	return 0;
+
+err_clk:
+	regulator_bulk_disable(qca_one->common->num_vregs, qca_one->common->vregs);
+err_bulk:
+	regulator_disable(qca_one->common->vddio);
+
+	return ret;
+}
+
+static void pwrseq_qca_power_off(struct pwrseq *pwrseq)
+{
+	struct pwrseq_qca_one *qca_one = pwrseq_get_drvdata(pwrseq);
+
+	if (qca_one->enable) {
+		gpiod_set_value_cansleep(qca_one->enable, 0);
+		msleep(50);
+	}
+
+	clk_disable_unprepare(qca_one->common->susclk);
+
+	regulator_bulk_disable(qca_one->common->num_vregs, qca_one->common->vregs);
+	regulator_disable(qca_one->common->vddio);
+
+	if (qca_one->common->sw_ctrl) {
+		bool sw_ctrl_state = gpiod_get_value_cansleep(qca_one->common->sw_ctrl);
+		dev_dbg(&pwrseq->dev, "SW_CTRL is %d", sw_ctrl_state);
+	}
+}
+
+static const struct pwrseq_ops pwrseq_qca_ops = {
+	.pre_power_on = pwrseq_qca_pre_power_on,
+	.power_on = pwrseq_qca_power_on,
+	.power_off = pwrseq_qca_power_off,
+};
+
+static int pwrseq_qca_common_init(struct device *dev, struct pwrseq_qca_common *qca_common,
+		const struct qca_device_data *data)
+{
+	int ret, i;
+
+	if (data->vddio.name) {
+		qca_common->vddio = devm_regulator_get(dev, data->vddio.name);
+		if (IS_ERR(qca_common->vddio))
+			return PTR_ERR(qca_common->vddio);
+
+		ret = regulator_set_load(qca_common->vddio, data->vddio.load_uA);
+		if (ret)
+			return ret;
+	}
+
+	qca_common->num_vregs = data->num_vregs;
+
+	for (i = 0; i < qca_common->num_vregs; i++)
+		qca_common->vregs[i].supply = data->vregs[i].name;
+
+	ret = devm_regulator_bulk_get(dev, qca_common->num_vregs, qca_common->vregs);
+	if (ret)
+		return ret;
+
+	for (i = 0; i < qca_common->num_vregs; i++) {
+		if (!data->vregs[i].load_uA)
+			continue;
+
+		ret = regulator_set_load(qca_common->vregs[i].consumer, data->vregs[i].load_uA);
+		if (ret)
+			return ret;
+	}
+
+	qca_common->susclk = devm_clk_get_optional(dev, NULL);
+	if (IS_ERR(qca_common->susclk)) {
+		dev_err(dev, "failed to acquire clk\n");
+		return PTR_ERR(qca_common->susclk);
+	}
+
+	qca_common->sw_ctrl = devm_gpiod_get_optional(dev, "swctrl", GPIOD_IN);
+	if (IS_ERR(qca_common->sw_ctrl)) {
+		return dev_err_probe(dev, PTR_ERR(qca_common->sw_ctrl),
+				"failed to acquire SW_CTRL gpio\n");
+	} else if (!qca_common->sw_ctrl)
+		dev_info(dev, "No SW_CTRL gpio\n");
+
+	return 0;
+}
+
+static void pwrseq_qca_unprepare_susclk(void *data)
+{
+	struct pwrseq_qca_common *qca_common = data;
+
+	clk_disable_unprepare(qca_common->susclk);
+}
+
+static const struct qca_device_data qca_soc_data_default = {
+	.num_vregs = 0,
+	.has_enable_gpios = true,
+};
+
+static int pwrseq_qca_probe(struct platform_device *pdev)
+{
+	struct pwrseq_qca *pwrseq_qca;
+	struct pwrseq *pwrseq;
+	struct pwrseq_provider *provider;
+	struct device *dev = &pdev->dev;
+	struct pwrseq_onecell_data *onecell;
+	const struct qca_device_data *data;
+	int ret, i;
+
+	data = device_get_match_data(dev);
+	if (!data)
+		data = &qca_soc_data_default;
+
+	pwrseq_qca = devm_kzalloc(dev, struct_size(pwrseq_qca, common.vregs, data->num_vregs), GFP_KERNEL);
+	if (!pwrseq_qca)
+		return -ENOMEM;
+
+	onecell = devm_kzalloc(dev, struct_size(onecell, pwrseqs, PWRSEQ_QCA_MAX), GFP_KERNEL);
+	if (!onecell)
+		return -ENOMEM;
+
+	ret = pwrseq_qca_common_init(dev, &pwrseq_qca->common, data);
+	if (ret)
+		return ret;
+
+	if (data->has_enable_gpios) {
+		struct gpio_desc *gpiod;
+
+		gpiod = devm_gpiod_get_optional(dev, "wifi-enable", GPIOD_OUT_LOW);
+		if (IS_ERR(gpiod))
+			return dev_err_probe(dev, PTR_ERR(gpiod), "failed to acquire WIFI enable GPIO\n");
+		else if (!gpiod)
+			dev_warn(dev, "No WiFi enable GPIO declared\n");
+
+		pwrseq_qca->pwrseq_qcas[PWRSEQ_QCA_WIFI].enable = gpiod;
+
+		gpiod = devm_gpiod_get_optional(dev, "bt-enable", GPIOD_OUT_LOW);
+		if (IS_ERR(gpiod))
+			return dev_err_probe(dev, PTR_ERR(gpiod), "failed to acquire BT enable GPIO\n");
+		else if (!gpiod)
+			dev_warn(dev, "No BT enable GPIO declared\n");
+
+		pwrseq_qca->pwrseq_qcas[PWRSEQ_QCA_BT].enable = gpiod;
+	}
+
+	/* If we have no control over device's enablement, make sure that sleep clock is always running */
+	if (!pwrseq_qca->common.vddio ||
+	    !pwrseq_qca->common.num_vregs ||
+	    !(pwrseq_qca->pwrseq_qcas[PWRSEQ_QCA_BT].enable &&
+	      pwrseq_qca->pwrseq_qcas[PWRSEQ_QCA_WIFI].enable)) {
+		ret = clk_set_rate(pwrseq_qca->common.susclk, SUSCLK_RATE_32KHZ);
+		if (ret)
+			return ret;
+
+		ret = clk_prepare_enable(pwrseq_qca->common.susclk);
+		if (ret)
+			return ret;
+
+		ret = devm_add_action_or_reset(dev, pwrseq_qca_unprepare_susclk, &pwrseq_qca->common);
+		if (ret)
+			return ret;
+	}
+
+	for (i = 0; i < PWRSEQ_QCA_MAX; i++) {
+		pwrseq_qca->pwrseq_qcas[i].common = &pwrseq_qca->common;
+
+		pwrseq = devm_pwrseq_create(dev, &pwrseq_qca_ops);
+		if (IS_ERR(pwrseq))
+			return PTR_ERR(pwrseq);
+
+		pwrseq_set_drvdata(pwrseq, &pwrseq_qca->pwrseq_qcas[i]);
+
+		onecell->pwrseqs[i] = pwrseq;
+	}
+
+	onecell->num = PWRSEQ_QCA_MAX;
+
+	provider = devm_of_pwrseq_provider_register(dev, of_pwrseq_xlate_onecell, onecell);
+
+	return PTR_ERR_OR_ZERO(provider);
+}
+
+static const struct qca_device_data qca_soc_data_qca6390 = {
+	.vddio = { "vddio", 20000 },
+	.vregs = {
+		/* 2.0 V */
+		{ "vddpcie2", 15000 },
+		{ "vddrfa3", 400000 },
+
+		/* 0.95 V */
+		{ "vddaon", 100000 },
+		{ "vddpmu", 1250000 },
+		{ "vddrfa1", 200000 },
+
+		/* 1.35 V */
+		{ "vddrfa2", 400000 },
+		{ "vddpcie1", 35000 },
+	},
+	.num_vregs = 7,
+	.has_enable_gpios = true,
+};
+
+/* Shared between wcn3990 and wcn3991 */
+static const struct qca_device_data qca_soc_data_wcn3990 = {
+	.vddio = { "vddio", 15000 },
+	.vregs = {
+		{ "vddxo", 80000  },
+		{ "vddrf", 300000 },
+		{ "vddch0", 450000 },
+		{ "vddch1", 450000 },
+	},
+	.num_vregs = 4,
+};
+
+static const struct qca_device_data qca_soc_data_wcn3998 = {
+	.vddio = { "vddio", 10000 },
+	.vregs = {
+		{ "vddxo", 80000  },
+		{ "vddrf", 300000 },
+		{ "vddch0", 450000 },
+		{ "vddch1", 450000 },
+	},
+	.num_vregs = 4,
+};
+
+static const struct qca_device_data qca_soc_data_wcn6750 = {
+	.vddio = { "vddio", 5000 },
+	.vregs = {
+		{ "vddaon", 26000 },
+		{ "vddbtcxmx", 126000 },
+		{ "vddrfacmn", 12500 },
+		{ "vddrfa0p8", 102000 },
+		{ "vddrfa1p7", 302000 },
+		{ "vddrfa1p2", 257000 },
+		{ "vddrfa2p2", 1700000 },
+		{ "vddasd", 200 },
+	},
+	.num_vregs = 8,
+	.has_enable_gpios = true,
+};
+
+static const struct of_device_id pwrseq_qca_of_match[] = {
+	{ .compatible = "qcom,qca6174-pwrseq", },
+	{ .compatible = "qcom,qca6390-pwrseq", .data = &qca_soc_data_qca6390 },
+	{ .compatible = "qcom,qca9377-pwrseq" },
+	{ .compatible = "qcom,wcn3990-pwrseq", .data = &qca_soc_data_wcn3990 },
+	{ .compatible = "qcom,wcn3991-pwrseq", .data = &qca_soc_data_wcn3990 },
+	{ .compatible = "qcom,wcn3998-pwrseq", .data = &qca_soc_data_wcn3998 },
+	{ .compatible = "qcom,wcn6750-pwrseq", .data = &qca_soc_data_wcn6750 },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, pwrseq_qca_of_match);
+
+static struct platform_driver pwrseq_qca_driver = {
+	.probe = pwrseq_qca_probe,
+	.driver = {
+		.name = "pwrseq_qca",
+		.of_match_table = pwrseq_qca_of_match,
+	},
+};
+
+module_platform_driver(pwrseq_qca_driver);
+MODULE_LICENSE("GPL v2");
-- 
2.33.0


  parent reply	other threads:[~2021-10-06  3:54 UTC|newest]

Thread overview: 29+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
     [not found] <2h9GS3myO9uyX8sDYwU_43cDbBCW_SE1h5qolKQLKT9ZVvz0-K6z6cix50eVsgMsYLtgTLsW37DxF0lf78vxCA==@protonmail.internalid>
2021-10-06  3:53 ` [PATCH v1 00/15] create power sequencing subsystem Dmitry Baryshkov
2021-10-06  3:53   ` [PATCH v1 01/15] dt-bindings: add pwrseq device tree bindings Dmitry Baryshkov
2021-10-26 12:53     ` Rob Herring
2021-10-26 14:42       ` Dmitry Baryshkov
2021-10-27 21:53         ` Rob Herring
2021-11-02 15:26           ` Dmitry Baryshkov
2023-03-10  7:56             ` Srinivas Kandagatla
2021-10-06  3:53   ` [PATCH v1 02/15] power: add power sequencer subsystem Dmitry Baryshkov
2021-10-06  3:53   ` [PATCH v1 03/15] pwrseq: port MMC's pwrseq drivers to new pwrseq subsystem Dmitry Baryshkov
2021-10-06  3:53   ` [PATCH v1 04/15] mmc: core: switch " Dmitry Baryshkov
2021-10-06  3:53   ` [PATCH v1 05/15] pwrseq: implement onecell helper Dmitry Baryshkov
2021-10-06  3:53   ` Dmitry Baryshkov [this message]
2021-10-06  3:53   ` [PATCH v1 07/15] pwrseq: add fallback support Dmitry Baryshkov
2021-10-06  3:54   ` [PATCH v1 08/15] pwrseq: pwrseq_qca: implement " Dmitry Baryshkov
2021-10-06  3:54   ` [PATCH v1 09/15] Bluetooth: hci_qca: switch to using pwrseq Dmitry Baryshkov
2021-10-06  3:54   ` [PATCH v1 10/15] ath10k: add support for pwrseq sequencing Dmitry Baryshkov
2021-10-07  5:31     ` Kalle Valo
2021-10-06  3:54   ` [PATCH v1 11/15] arm64: dts: qcom: sdm845-db845c: switch bt+wifi to qca power sequencer Dmitry Baryshkov
2021-10-06  3:54   ` [PATCH v1 12/15] arm64: dts: qcom: qrb5165-rb5: add bluetooth support Dmitry Baryshkov
2021-10-06  3:54   ` [PATCH v1 13/15] arm64: dts: qcom: sdm845-db845c: add second channel to qca power sequencer Dmitry Baryshkov
2021-10-06  3:54   ` [PATCH v1 14/15] WIP: PCI: qcom: use pwrseq to power up bus devices Dmitry Baryshkov
2021-10-06  3:54   ` [PATCH v1 15/15] WIP: arm64: dts: qcom: qrb5165-rb5: add bus-pwrseq property to pcie0 Dmitry Baryshkov
2021-10-07  5:27   ` [PATCH v1 00/15] create power sequencing subsystem Kalle Valo
2021-11-02 14:05   ` Caleb Connolly
2022-09-23 14:39   ` Luca Weiss
2022-10-13 19:50   ` Matthias Kaehlcke
2022-10-19  6:03     ` Dmitry Baryshkov
2023-03-01  8:17       ` Alexander Stein
2023-03-01  9:02         ` Ulf Hansson

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20211006035407.1147909-7-dmitry.baryshkov@linaro.org \
    --to=dmitry.baryshkov@linaro.org \
    --cc=agross@kernel.org \
    --cc=ath10k@lists.infradead.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=davem@davemloft.net \
    --cc=johan.hedberg@gmail.com \
    --cc=kuba@kernel.org \
    --cc=kvalo@codeaurora.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-bluetooth@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mmc@vger.kernel.org \
    --cc=linux-wireless@vger.kernel.org \
    --cc=luiz.dentz@gmail.com \
    --cc=marcel@holtmann.org \
    --cc=netdev@vger.kernel.org \
    --cc=svarbanov@mm-sol.com \
    --cc=ulf.hansson@linaro.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).