From: Katherine Perez <kaperez@linux.microsoft.com>
To: Bjorn Andersson <bjorn.andersson@linaro.org>,
Vinod Koul <vkoul@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Subject: [RFC PATCH 3/4] arm64: dts: qcom: sm8150: add DSI display nodes
Date: Wed, 10 Nov 2021 09:03:29 -0800 [thread overview]
Message-ID: <20211110170330.1789509-4-kaperez@linux.microsoft.com> (raw)
In-Reply-To: <20211110170330.1789509-1-kaperez@linux.microsoft.com>
Add DSI controller and PHY nodes to sm8150.
Signed-off-by: Katherine Perez <kaperez@linux.microsoft.com>
---
arch/arm64/boot/dts/qcom/sm8150.dtsi | 183 ++++++++++++++++++++++++++-
1 file changed, 179 insertions(+), 4 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
index 38dbc39103ba..afa612daefa1 100644
--- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
@@ -3261,6 +3261,35 @@ camnoc_virt: interconnect@ac00000 {
qcom,bcm-voters = <&apps_bcm_voter>;
};
+ dsi_opp_table: dsi-opp-table {
+ compatible = "operating-points-v2";
+
+ opp-19200000 {
+ opp-hz = /bits/ 64 <19200000>;
+ required-opps = <&rpmhpd_opp_min_svs>;
+ };
+
+ opp-180000000 {
+ opp-hz = /bits/ 64 <180000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-275000000 {
+ opp-hz = /bits/ 64 <275000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-328580000 {
+ opp-hz = /bits/ 64 <328580000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-358000000 {
+ opp-hz = /bits/ 64 <358000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+
mdss: mdss@ae00000 {
compatible = "qcom,sm8150-mdss";
reg = <0 0x0ae00000 0 0x1000>;
@@ -3351,6 +3380,152 @@ opp-460000000 {
};
};
};
+
+ dsi0: dsi@ae94000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0 0x0ae94000 0 0x400>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+ <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
+ assigned-clock-parents = <&dsi0_phy 0>, <&dsi0_phy 1>;
+
+ operating-points-v2 = <&dsi_opp_table>;
+ power-domains = <&rpmhpd SM8150_MMCX>;
+
+ phys = <&dsi0_phy>;
+ phy-names = "dsi";
+
+ status = "disabled";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi0_in: endpoint {
+ remote-endpoint = <&dpu_intf1_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi0_out: endpoint {
+ };
+ };
+ };
+ };
+
+ dsi0_phy: dsi-phy@ae94400 {
+ compatible = "qcom,dsi-phy-7nm-8150";
+ reg = <0 0x0ae94400 0 0x200>,
+ <0 0x0ae94600 0 0x280>,
+ <0 0x0ae94900 0 0x260>;
+ reg-names = "dsi_phy",
+ "dsi_phy_lane",
+ "dsi_pll";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "ref";
+
+ status = "disabled";
+ };
+
+ dsi1: dsi@ae96000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0 0x0ae96000 0 0x400>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
+ <&dispcc DISP_CC_MDSS_ESC1_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>;
+ assigned-clock-parents = <&dsi1_phy 0>, <&dsi1_phy 1>;
+
+ operating-points-v2 = <&dsi_opp_table>;
+ power-domains = <&rpmhpd SM8150_CX>;
+
+ phys = <&dsi1_phy>;
+ phy-names = "dsi";
+
+ status = "disabled";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi1_in: endpoint {
+ remote-endpoint = <&dpu_intf2_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi1_out: endpoint {
+ };
+ };
+ };
+ };
+
+ dsi1_phy: dsi-phy@ae96400 {
+ compatible = "qcom,dsi-phy-7nm-8150";
+ reg = <0 0x0ae96400 0 0x200>,
+ <0 0x0ae96600 0 0x280>,
+ <0 0x0ae96900 0 0x260>;
+ reg-names = "dsi_phy",
+ "dsi_phy_lane",
+ "dsi_pll";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "ref";
+
+ status = "disabled";
+ };
};
dispcc: clock-controller@af00000 {
@@ -3359,10 +3534,10 @@ dispcc: clock-controller@af00000 {
power-domains = <&rpmhpd SM8150_MMCX>;
required-opps = <&rpmhpd_opp_low_svs>;
clocks = <&rpmhcc RPMH_CXO_CLK>,
- <0>,
- <0>,
- <0>,
- <0>,
+ <&dsi0_phy 0>,
+ <&dsi0_phy 1>,
+ <&dsi1_phy 0>,
+ <&dsi1_phy 1>,
<0>,
<0>;
clock-names = "bi_tcxo",
--
2.31.1
next prev parent reply other threads:[~2021-11-10 17:03 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-11-10 17:03 [RFC PATCH 0/4] arm64: dts: sm8150: display support for Microsoft Surface Duo Katherine Perez
2021-11-10 17:03 ` [RFC PATCH 1/4] arm64: dts: qcom: sm8150: add dispcc node Katherine Perez
2021-11-11 21:56 ` Konrad Dybcio
2021-11-10 17:03 ` [RFC PATCH 2/4] arm64: dts: qcom: sm8150: add display nodes Katherine Perez
2021-11-11 22:00 ` Konrad Dybcio
2021-11-10 17:03 ` Katherine Perez [this message]
2021-11-10 17:03 ` [RFC PATCH 4/4] arm64: dts: qcom: sm8150: display support for Microsoft Surface Duo Katherine Perez
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20211110170330.1789509-4-kaperez@linux.microsoft.com \
--to=kaperez@linux.microsoft.com \
--cc=bjorn.andersson@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).