From: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
To: Andy Gross <agross@kernel.org>,
Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konrad.dybcio@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>,
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Subject: [PATCH v2 2/3] arm64: dts: qcom: sm8450: add Soundwire and LPASS
Date: Tue, 15 Nov 2022 12:00:52 +0100 [thread overview]
Message-ID: <20221115110053.110319-3-krzysztof.kozlowski@linaro.org> (raw)
In-Reply-To: <20221115110053.110319-1-krzysztof.kozlowski@linaro.org>
From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Add Soundwire controllers, Low Power Audio SubSystem (LPASS) devices and
LPASS pin controller.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Co-developed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
Changes since v1:
1. Whitespace cleanups.
2. Correct include - do not use deprecated one.
---
arch/arm64/boot/dts/qcom/sm8450.dtsi | 295 +++++++++++++++++++++++++++
1 file changed, 295 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 4b0a1eee8bd9..e80a7d09646f 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -15,6 +15,7 @@
#include <dt-bindings/interconnect/qcom,sm8450.h>
#include <dt-bindings/soc/qcom,gpr.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+#include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h>
#include <dt-bindings/thermal/thermal.h>
/ {
@@ -2097,6 +2098,212 @@ compute-cb@3 {
};
};
+ wsa2macro: codec@31e0000 {
+ compatible = "qcom,sm8450-lpass-wsa-macro";
+ reg = <0 0x031e0000 0 0x1000>;
+ clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&vamacro>;
+ clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
+ assigned-clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+ assigned-clock-rates = <19200000>, <19200000>;
+
+ #clock-cells = <0>;
+ clock-output-names = "wsa2-mclk";
+ #sound-dai-cells = <1>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wsa2_swr_active>;
+ };
+
+ /* WSA2 */
+ swr4: soundwire-controller@31f0000 {
+ reg = <0 0x031f0000 0 0x2000>;
+ compatible = "qcom,soundwire-v1.7.0";
+ interrupts = <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&wsa2macro>;
+ clock-names = "iface";
+
+ qcom,din-ports = <2>;
+ qcom,dout-ports = <6>;
+
+ qcom,ports-sinterval-low = /bits/ 8 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0x0f 0x0f>;
+ qcom,ports-offset1 = /bits/ 8 <0x01 0x02 0x0c 0x06 0x12 0x0d 0x07 0x0a>;
+ qcom,ports-offset2 = /bits/ 8 <0xff 0x00 0x1f 0xff 0x00 0x1f 0x00 0x00>;
+ qcom,ports-hstart = /bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
+ qcom,ports-hstop = /bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
+ qcom,ports-word-length = /bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
+ qcom,ports-block-pack-mode = /bits/ 8 <0xFF 0xFF 0x01 0xFF 0xFF 0x01 0xFF 0xFF>;
+ qcom,ports-block-group-count = /bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
+ qcom,ports-lane-control = /bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
+
+ #sound-dai-cells = <1>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+ };
+
+ rxmacro: codec@3200000 {
+ compatible = "qcom,sm8450-lpass-rx-macro";
+ reg = <0 0x3200000 0 0x1000>;
+ clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&vamacro>;
+ clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
+
+ assigned-clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+ assigned-clock-rates = <19200000>, <19200000>;
+
+ #clock-cells = <0>;
+ clock-output-names = "mclk";
+ #sound-dai-cells = <1>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&rx_swr_active>;
+ };
+
+ swr1: soundwire-controller@3210000 {
+ reg = <0 0x3210000 0 0x2000>;
+ compatible = "qcom,soundwire-v1.7.0";
+ interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rxmacro>;
+ clock-names = "iface";
+ label = "RX";
+ qcom,din-ports = <0>;
+ qcom,dout-ports = <5>;
+
+ qcom,ports-sinterval-low = /bits/ 8 <0x03 0x1F 0x1F 0x07 0x00>;
+ qcom,ports-offset1 = /bits/ 8 <0x00 0x00 0x0B 0x01 0x00>;
+ qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x0B 0x00 0x00>;
+ qcom,ports-hstart = /bits/ 8 <0xFF 0x03 0xFF 0xFF 0xFF>;
+ qcom,ports-hstop = /bits/ 8 <0xFF 0x06 0xFF 0xFF 0xFF>;
+ qcom,ports-word-length = /bits/ 8 <0x01 0x07 0x04 0xFF 0xFF>;
+ qcom,ports-block-pack-mode = /bits/ 8 <0xFF 0x00 0x01 0xFF 0xFF>;
+ qcom,ports-lane-control = /bits/ 8 <0x01 0x00 0x00 0x00 0x00>;
+ qcom,ports-block-group-count = /bits/ 8 <0xFF 0xFF 0xFF 0xFF 0x00>;
+ #sound-dai-cells = <1>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+ };
+
+ txmacro: codec@3220000 {
+ compatible = "qcom,sm8450-lpass-tx-macro";
+ reg = <0 0x3220000 0 0x1000>;
+ clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&vamacro>;
+ clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
+ assigned-clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+ assigned-clock-rates = <19200000>, <19200000>;
+
+ #clock-cells = <0>;
+ clock-output-names = "mclk";
+ #sound-dai-cells = <1>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tx_swr_active>;
+ };
+
+ wsamacro: codec@3240000 {
+ compatible = "qcom,sm8450-lpass-wsa-macro";
+ reg = <0 0x03240000 0 0x1000>;
+ clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&vamacro>;
+ clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
+
+ assigned-clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+ assigned-clock-rates = <19200000>, <19200000>;
+
+ #clock-cells = <0>;
+ clock-output-names = "mclk";
+ #sound-dai-cells = <1>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wsa_swr_active>;
+ };
+
+ /* WSA */
+ swr0: soundwire-controller@3250000 {
+ reg = <0 0x03250000 0 0x2000>;
+ compatible = "qcom,soundwire-v1.7.0";
+ interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&wsamacro>;
+ clock-names = "iface";
+
+ qcom,din-ports = <2>;
+ qcom,dout-ports = <6>;
+
+ qcom,ports-sinterval-low = /bits/ 8 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0x0f 0x0f>;
+ qcom,ports-offset1 = /bits/ 8 <0x01 0x02 0x0c 0x06 0x12 0x0d 0x07 0x0a>;
+ qcom,ports-offset2 = /bits/ 8 <0xff 0x00 0x1f 0xff 0x00 0x1f 0x00 0x00>;
+ qcom,ports-hstart = /bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
+ qcom,ports-hstop = /bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
+ qcom,ports-word-length = /bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
+ qcom,ports-block-pack-mode = /bits/ 8 <0xFF 0xFF 0x01 0xFF 0xFF 0x01 0xFF 0xFF>;
+ qcom,ports-block-group-count = /bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
+ qcom,ports-lane-control = /bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF>;
+ qcom,port-offset = <1>;
+ #sound-dai-cells = <1>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+ };
+
+ swr2: soundwire-controller@33b0000 {
+ reg = <0 0x33b0000 0 0x2000>;
+ compatible = "qcom,soundwire-v1.7.0";
+ interrupts-extended = <&intc GIC_SPI 496 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 520 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "core", "wake";
+
+ clocks = <&vamacro>;
+ clock-names = "iface";
+ label = "TX";
+
+ qcom,din-ports = <4>;
+ qcom,dout-ports = <0>;
+ qcom,ports-sinterval-low = /bits/ 8 <0x01 0x01 0x03 0x03>;
+ qcom,ports-offset1 = /bits/ 8 <0x00 0x00 0x01 0x01>;
+ qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x00 0x00>;
+ qcom,ports-block-pack-mode = /bits/ 8 <0xFF 0xFF 0xFF 0xFF>;
+ qcom,ports-hstart = /bits/ 8 <0xFF 0xFF 0xFF 0xFF>;
+ qcom,ports-hstop = /bits/ 8 <0xFF 0xFF 0xFF 0xFF>;
+ qcom,ports-word-length = /bits/ 8 <0xFF 0xFF 0xFF 0xFF>;
+ qcom,ports-block-group-count = /bits/ 8 <0xFF 0xFF 0xFF 0xFF>;
+ qcom,ports-lane-control = /bits/ 8 <0x01 0x02 0x00 0x00>;
+ qcom,port-offset = <1>;
+ #sound-dai-cells = <1>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+ };
+
+ vamacro: codec@33f0000 {
+ compatible = "qcom,sm8450-lpass-va-macro";
+ reg = <0 0x033f0000 0 0x1000>;
+ clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+ clock-names = "mclk", "macro", "dcodec", "npl";
+ assigned-clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+ assigned-clock-rates = <19200000>;
+
+ #clock-cells = <0>;
+ clock-output-names = "fsgen";
+ #sound-dai-cells = <1>;
+ };
+
remoteproc_adsp: remoteproc@30000000 {
compatible = "qcom,sm8450-adsp-pas";
reg = <0 0x030000000 0 0x100>;
@@ -3030,6 +3237,91 @@ qup_uart20_default: qup-uart20-default-state {
};
+ lpass_tlmm: pinctrl@3440000{
+ compatible = "qcom,sm8450-lpass-lpi-pinctrl";
+ reg = <0 0x3440000 0x0 0x20000>,
+ <0 0x34d0000 0x0 0x10000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&lpass_tlmm 0 0 23>;
+
+ clocks = <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+ clock-names = "core", "audio";
+
+ wsa_swr_active: wsa-swr-active-state {
+ clk-pins {
+ pins = "gpio10";
+ function = "wsa_swr_clk";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-disable;
+ };
+
+ data-pins {
+ pins = "gpio11";
+ function = "wsa_swr_data";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-bus-hold;
+ };
+ };
+
+ tx_swr_active: tx-swr-active-state {
+ clk-pins {
+ pins = "gpio0";
+ function = "swr_tx_clk";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-disable;
+ };
+
+ data-pins {
+ pins = "gpio1", "gpio2", "gpio14";
+ function = "swr_tx_data";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-bus-hold;
+ };
+ };
+
+ rx_swr_active: rx-swr-active-state {
+ clk-pins {
+ pins = "gpio3";
+ function = "swr_rx_clk";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-disable;
+ };
+
+ data-pins {
+ pins = "gpio4", "gpio5";
+ function = "swr_rx_data";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-bus-hold;
+ };
+ };
+
+ wsa2_swr_active: wsa2-swr-active-state {
+ clk-pins {
+ pins = "gpio15";
+ function = "wsa2_swr_clk";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-disable;
+ };
+
+ data-pins {
+ pins = "gpio16";
+ function = "wsa2_swr_data";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-bus-hold;
+ };
+ };
+ };
+
apps_smmu: iommu@15000000 {
compatible = "qcom,sm8450-smmu-500", "arm,mmu-500";
reg = <0 0x15000000 0 0x100000>;
@@ -3507,6 +3799,9 @@ lpass_ag_noc: interconnect@3c40000 {
};
};
+ sound: sound {
+ };
+
thermal-zones {
aoss0-thermal {
polling-delay-passive = <0>;
--
2.34.1
next prev parent reply other threads:[~2022-11-15 11:02 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-11-15 11:00 [PATCH v2 0/3] arm64: dts: qcom: sm8450-hdk: add sound support Krzysztof Kozlowski
2022-11-15 11:00 ` [PATCH v2 1/3] arm64: dts: qcom: sm8450: add GPR node Krzysztof Kozlowski
2022-11-15 11:02 ` Konrad Dybcio
2022-11-15 11:00 ` Krzysztof Kozlowski [this message]
2022-11-15 11:17 ` [PATCH v2 2/3] arm64: dts: qcom: sm8450: add Soundwire and LPASS Konrad Dybcio
2022-11-15 11:19 ` Krzysztof Kozlowski
2022-11-15 11:00 ` [PATCH v2 3/3] arm64: dts: qcom: sm8450-hdk: add sound support Krzysztof Kozlowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20221115110053.110319-3-krzysztof.kozlowski@linaro.org \
--to=krzysztof.kozlowski@linaro.org \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konrad.dybcio@linaro.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=srinivas.kandagatla@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).