Linux-ARM-MSM Archive on lore.kernel.org
 help / color / Atom feed
From: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
To: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-remoteproc@vger.kernel.org, linux-arm-msm@vger.kernel.org,
	spjoshi@codeaurora.org, kaushalk@codeaurora.org
Subject: Re: [PATCH 1/5] remoteproc: Add q6v55 specific parameters and enable probing for q6v55
Date: Fri, 4 Nov 2016 18:57:41 +0530
Message-ID: <6169b510-c48b-d422-0e3d-8cdd3afca429@codeaurora.org> (raw)
In-Reply-To: <20161025184708.GM7509@tuxbot>



On 10/26/2016 12:17 AM, Bjorn Andersson wrote:
> On Mon 24 Oct 08:55 PDT 2016, Avaneesh Kumar Dwivedi wrote:
>
>> Adding required definition of parameters along with new structure
>> fields specific to q6v55 and enabling probe for q6v55 mss remote-
>> proc driver.
>>
>> Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
>> ---
>>   .../devicetree/bindings/remoteproc/qcom,q6v5.txt   |  3 +-
>>   drivers/remoteproc/qcom_q6v5_pil.c                 | 33 ++++++++++++++++++++--
>>   2 files changed, 32 insertions(+), 4 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
>> index 57cb49e..0986f8b 100644
>> --- a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
>> +++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
>> @@ -7,7 +7,8 @@ on the Qualcomm Hexagon core.
>>   	Usage: required
>>   	Value type: <string>
>>   	Definition: must be one of:
>> -		    "qcom,q6v5-pil"
>> +		    "qcom,q6v5-pil",
>> +			"qcom,q6v55-pil"
>>   
>>   - reg:
>>   	Usage: required
>> diff --git a/drivers/remoteproc/qcom_q6v5_pil.c b/drivers/remoteproc/qcom_q6v5_pil.c
>> index 2e0caaa..8df95a0 100644
>> --- a/drivers/remoteproc/qcom_q6v5_pil.c
>> +++ b/drivers/remoteproc/qcom_q6v5_pil.c
>> @@ -30,13 +30,14 @@
>>   #include <linux/reset.h>
>>   #include <linux/soc/qcom/smem.h>
>>   #include <linux/soc/qcom/smem_state.h>
>> +#include <linux/mutex.h>
>>   
>>   #include "remoteproc_internal.h"
>>   #include "qcom_mdt_loader.h"
>>   
>>   #include <linux/qcom_scm.h>
>>   
>> -#define MBA_FIRMWARE_NAME		"mba.b00"
>> +#define MBA_FIRMWARE_NAME		"mba.mbn"
> On 8974 we must load the mba.b00, on 8916 and 8996 we must load mba.mbn.
> But looking at downstream we seem to have:
>
> 8974: q6v5 -> mba.b00
> 8916: q6v56 -> mba.mbn
> 8996: q6v55 -> mba.mbn
>
> So we should be able to pick this based on compatible then.
OK, have take care of in patch set v2
>
>>   #define MPSS_FIRMWARE_NAME		"modem.mdt"
>>   
>>   #define MPSS_CRASH_REASON_SMEM		421
>> @@ -65,6 +66,8 @@
>>   #define QDSP6SS_RESET_REG		0x014
>>   #define QDSP6SS_GFMUX_CTL_REG		0x020
>>   #define QDSP6SS_PWR_CTL_REG		0x030
>> +#define QDSP6SS_MEM_PWR_CTL		0x0B0
>> +#define QDSP6SS_STRAP_ACC		0x110
>>   
>>   /* AXI Halt Register Offsets */
>>   #define AXI_HALTREQ_REG			0x0
>> @@ -93,13 +96,24 @@
>>   #define QDSS_BHS_ON			BIT(21)
>>   #define QDSS_LDO_BYP			BIT(22)
>>   
>> +/* QDSP6v55 parameters */
>> +#define QDSP6v55_LDO_BYP                BIT(25)
>> +#define QDSP6v55_BHS_ON                 BIT(24)
>> +#define QDSP6v55_CLAMP_WL               BIT(21)
>> +#define QDSP6v55_CLAMP_QMC_MEM          BIT(22)
>> +
>> +#define HALT_CHECK_MAX_LOOPS            (200)
>> +#define QDSP6SS_XO_CBCR                 (0x0038)
>> +
>> +#define QDSP6SS_ACC_OVERRIDE_VAL	0x20
>> +
>>   struct q6v5 {
>>   	struct device *dev;
>>   	struct rproc *rproc;
>>   
>>   	void __iomem *reg_base;
>>   	void __iomem *rmb_base;
>> -
>> +	void __iomem *restart_reg;
> The restart_reg is a register in the gcc, on 8974 this is exposed as a
> reset by gcc. Please add the GCC_MSS_RESTART to the list of resets in
> gcc-msm8996 rather than remapping and poking the register directly from
> this driver.
         Infact i had done it the way suggested above before i sent out 
initial
         patchset, but then when i discussed with internal clock team, 
they said they will
         not support MSS RESET to be done via GCC because

         "MSS_RESET is not a block reset, GCC reset controller is used 
only when we need a BCR to be reset,
         and which has a special purpose. MSS RESET doesn't fall under 
block resets, it is not a clock and
         cannot be associated with clock."

         Downstream also MSS RESET is programmed through dev_ioremap.
>
>>   	struct regmap *halt_map;
>>   	u32 halt_q6;
>>   	u32 halt_modem;
>> @@ -115,6 +129,13 @@ struct q6v5 {
>>   	struct clk *ahb_clk;
>>   	struct clk *axi_clk;
>>   	struct clk *rom_clk;
>> +	struct clk *gpll0_mss_clk;
>> +	struct clk *snoc_axi_clk;
>> +	struct clk *mnoc_axi_clk;
>> +
>> +	struct clk *xo;
>> +	struct clk *pnoc_clk;
>> +	struct clk *qdss_clk;
> Please introduce these changes as they are needed by the implementation,
> rather than in a separate patch. It makes it much much easier to review.
OK, have take care of in patch set v2
>
>>   
>>   	struct completion start_done;
>>   	struct completion stop_done;
>> @@ -128,13 +149,18 @@ struct q6v5 {
>>   	phys_addr_t mpss_reloc;
>>   	void *mpss_region;
>>   	size_t mpss_size;
>> +	struct mutex q6_lock;
>> +	u32 boot_count;
>> +	bool unvote_flag;
>> +	bool is_q6v55;
>> +	bool ahb_clk_vote;
> Dito
>
>>   };
>>   
>>   enum {
>>   	Q6V5_SUPPLY_CX,
>>   	Q6V5_SUPPLY_MX,
>> -	Q6V5_SUPPLY_MSS,
>>   	Q6V5_SUPPLY_PLL,
>> +	Q6V5_SUPPLY_MSS,
>>   };
>>   
>>   static int q6v5_regulator_init(struct q6v5 *qproc)
>> @@ -892,6 +918,7 @@ static int q6v5_remove(struct platform_device *pdev)
>>   
>>   static const struct of_device_id q6v5_of_match[] = {
>>   	{ .compatible = "qcom,q6v5-pil", },
>> +	{ .compatible = "qcom,q6v55-pil", },
> Just out of curiosity, is the version 55 or 5.5?
Version is q6v56 1.3
>
>>   	{ },
>>   };
> Regards,
> Bjorn

  reply index

Thread overview: 17+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-10-24 15:55 [PATCH 0/5] Self authenticating hexagon driver " Avaneesh Kumar Dwivedi
2016-10-24 15:55 ` [PATCH 1/5] remoteproc: Add q6v55 specific parameters and enable probing " Avaneesh Kumar Dwivedi
2016-10-25 18:47   ` Bjorn Andersson
2016-11-04 13:27     ` Avaneesh Kumar Dwivedi [this message]
2016-11-08  5:28       ` Bjorn Andersson
2016-10-24 15:55 ` [PATCH 2/5] remoteproc: Adding q6v55 specific regulator, clk, reset interface Avaneesh Kumar Dwivedi
2016-10-25 19:05   ` Bjorn Andersson
2016-11-04 13:41     ` Avaneesh Kumar Dwivedi
2016-10-24 15:55 ` [PATCH 3/5] remoteproc: Adding reset sequence and halt seq changes for q6v55 Avaneesh Kumar Dwivedi
2016-10-25 19:15   ` Bjorn Andersson
2016-11-04 13:42     ` Avaneesh Kumar Dwivedi
2016-10-24 15:55 ` [PATCH 4/5] remoteproc: Add start and shutdown interface " Avaneesh Kumar Dwivedi
2016-10-25 19:27   ` Bjorn Andersson
2016-11-04 13:46     ` Avaneesh Kumar Dwivedi
2016-10-24 15:55 ` [PATCH 5/5] remoteproc: Modifying probe for initializing q6v55 specific resources Avaneesh Kumar Dwivedi
2016-10-25 19:35   ` Bjorn Andersson
2016-11-04 13:47     ` Avaneesh Kumar Dwivedi

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=6169b510-c48b-d422-0e3d-8cdd3afca429@codeaurora.org \
    --to=akdwived@codeaurora.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=kaushalk@codeaurora.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-remoteproc@vger.kernel.org \
    --cc=spjoshi@codeaurora.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-ARM-MSM Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-arm-msm/0 linux-arm-msm/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-arm-msm linux-arm-msm/ https://lore.kernel.org/linux-arm-msm \
		linux-arm-msm@vger.kernel.org
	public-inbox-index linux-arm-msm

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-arm-msm


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git