From: Sarangdhar Joshi <spjoshi@codeaurora.org>
To: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Ohad Ben-Cohen <ohad@wizery.com>,
linux-remoteproc@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-arm-msm@vger.kernel.org,
Stephen Boyd <sboyd@codeaurora.org>,
Trilok Soni <tsoni@codeaurora.org>
Subject: Re: [PATCH v2 1/1] remoteproc: Add support for xo clock
Date: Wed, 2 Nov 2016 11:58:36 -0700 [thread overview]
Message-ID: <8284ee04-1e59-fd20-a215-7d0e22026cdc@codeaurora.org> (raw)
In-Reply-To: <20161101000555.GK25787@tuxbot>
On 10/31/2016 05:05 PM, Bjorn Andersson wrote:
> On Tue 25 Oct 13:57 PDT 2016, Sarangdhar Joshi wrote:
>
>> Add xo clock support required to boot up Qualcomm ADSP processor.
>> The ADSP remoteproc driver keeps xo clock enabled until the
>> driver receives "handover" irq, in order to allow ADSP processor
>> to vote for xo clock with rpm.
>
> Looks good, thanks.
>
> We have to add the clock to the DT binding and run that by Rob again,
> before merging the driver and this patch.
>
> Regards,
> Bjorn
Sure, will add it to the DT bindings. Thanks for reviewing.
Regards,
Sarang
>
>>
>> Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
>> ---
>> drivers/remoteproc/qcom_adsp_pil.c | 30 +++++++++++++++++++++++++++++-
>> 1 file changed, 29 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/remoteproc/qcom_adsp_pil.c b/drivers/remoteproc/qcom_adsp_pil.c
>> index 9141633..5bb25d1 100644
>> --- a/drivers/remoteproc/qcom_adsp_pil.c
>> +++ b/drivers/remoteproc/qcom_adsp_pil.c
>> @@ -15,6 +15,7 @@
>> * GNU General Public License for more details.
>> */
>>
>> +#include <linux/clk.h>
>> #include <linux/firmware.h>
>> #include <linux/interrupt.h>
>> #include <linux/kernel.h>
>> @@ -48,6 +49,8 @@ struct qcom_adsp {
>> struct qcom_smem_state *state;
>> unsigned stop_bit;
>>
>> + struct clk *xo;
>> +
>> struct regulator *cx_supply;
>>
>> struct completion start_done;
>> @@ -102,10 +105,14 @@ static int adsp_start(struct rproc *rproc)
>> struct qcom_adsp *adsp = (struct qcom_adsp *)rproc->priv;
>> int ret;
>>
>> - ret = regulator_enable(adsp->cx_supply);
>> + ret = clk_prepare_enable(adsp->xo);
>> if (ret)
>> return ret;
>>
>> + ret = regulator_enable(adsp->cx_supply);
>> + if (ret)
>> + goto disable_clocks;
>> +
>> ret = qcom_scm_pas_auth_and_reset(ADSP_PAS_ID);
>> if (ret) {
>> dev_err(adsp->dev,
>> @@ -126,6 +133,8 @@ static int adsp_start(struct rproc *rproc)
>>
>> disable_regulators:
>> regulator_disable(adsp->cx_supply);
>> +disable_clocks:
>> + clk_disable_unprepare(adsp->xo);
>>
>> return ret;
>> }
>> @@ -223,6 +232,21 @@ static irqreturn_t adsp_stop_ack_interrupt(int irq, void *dev)
>> return IRQ_HANDLED;
>> }
>>
>> +static int adsp_init_clock(struct qcom_adsp *adsp)
>> +{
>> + int ret;
>> +
>> + adsp->xo = devm_clk_get(adsp->dev, "xo");
>> + if (IS_ERR(adsp->xo)) {
>> + ret = PTR_ERR(adsp->xo);
>> + if (ret != -EPROBE_DEFER)
>> + dev_err(adsp->dev, "failed to get xo clock");
>> + return ret;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> static int adsp_init_regulator(struct qcom_adsp *adsp)
>> {
>> adsp->cx_supply = devm_regulator_get(adsp->dev, "cx");
>> @@ -320,6 +344,10 @@ static int adsp_probe(struct platform_device *pdev)
>> if (ret)
>> goto free_rproc;
>>
>> + ret = adsp_init_clock(adsp);
>> + if (ret)
>> + goto free_rproc;
>> +
>> ret = adsp_init_regulator(adsp);
>> if (ret)
>> goto free_rproc;
>> --
>> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
>> a Linux Foundation Collaborative Project
>>
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
prev parent reply other threads:[~2016-11-02 18:58 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-10-25 20:57 [PATCH v2 1/1] remoteproc: Add support for xo clock Sarangdhar Joshi
2016-10-25 21:03 ` Sarangdhar Joshi
2016-11-01 0:05 ` Bjorn Andersson
2016-11-01 17:41 ` Stephen Boyd
2016-11-01 17:46 ` Bjorn Andersson
2016-11-01 17:52 ` Stephen Boyd
2016-11-02 18:58 ` Sarangdhar Joshi [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=8284ee04-1e59-fd20-a215-7d0e22026cdc@codeaurora.org \
--to=spjoshi@codeaurora.org \
--cc=bjorn.andersson@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-remoteproc@vger.kernel.org \
--cc=ohad@wizery.com \
--cc=sboyd@codeaurora.org \
--cc=tsoni@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).