From mboxrd@z Thu Jan  1 00:00:00 1970
From: Marc Zyngier <marc.zyngier@arm.com>
Subject: Re: [PATCH v6 07/15] qcom: spmi-gpio: add support for hierarchical IRQ chip
Date: Sun, 20 Jan 2019 11:32:29 +0000
Message-ID: <86imyja7jm.wl-marc.zyngier@arm.com>
References: <20190119204252.18370-1-masneyb@onstation.org>
        <20190119204252.18370-8-masneyb@onstation.org>
Mime-Version: 1.0 (generated by SEMI-EPG 1.14.7 - "Harue")
Content-Type: text/plain; charset=US-ASCII
Return-path: <linux-kernel-owner@vger.kernel.org>
In-Reply-To: <20190119204252.18370-8-masneyb@onstation.org>
Sender: linux-kernel-owner@vger.kernel.org
To: Brian Masney <masneyb@onstation.org>
Cc: linus.walleij@linaro.org, sboyd@kernel.org, bjorn.andersson@linaro.org, andy.gross@linaro.org, shawnguo@kernel.org, dianders@chromium.org, linux-gpio@vger.kernel.org, nicolas.dechesne@linaro.org, niklas.cassel@linaro.org, david.brown@linaro.org, robh+dt@kernel.org, mark.rutland@arm.com, thierry.reding@gmail.com, linux-arm-msm@vger.kernel.org, linux-kernel@vger.kernel.org, devicetree@vger.kernel.org
List-Id: linux-arm-msm@vger.kernel.org

On Sat, 19 Jan 2019 20:42:44 +0000,
Brian Masney <masneyb@onstation.org> wrote:
> 
> spmi-gpio did not have any irqchip support so consumers of this in
> device tree would need to call gpio[d]_to_irq() in order to get the
> proper IRQ on the underlying PMIC. IRQ chips in device tree should
> be usable from the start without the consumer having to make an
> additional call to get the proper IRQ on the parent. This patch adds
> hierarchical IRQ chip support to the spmi-gpio code to correct this
> issue.
> 
> Driver was tested using the volume buttons (via gpio-keys) on the LG
> Nexus 5 (hammerhead) phone with the following two configurations.
> 
> volume-up {
>         interrupts-extended = <&pm8941_gpios 2 IRQ_TYPE_EDGE_BOTH>;
>         ...
> };
> 
> volume-up {
>         gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
>         ...
> };
> 
> Both configurations now show that spmi-gpio is the IRQ domain and that
> the IRQ is setup in a hierarchy.
> 
> $ grep volume_up /proc/interrupts
>  72:          6          0  spmi-gpio   1 Edge      volume_up
> 
> $ cat /sys/kernel/debug/irq/irqs/72
> handler:  handle_edge_irq
> device:   (null)
> status:   0x00000403
>             _IRQ_NOPROBE
> istate:   0x00000000
> ddepth:   0
> wdepth:   0
> dstate:   0x02400203
>             IRQ_TYPE_EDGE_RISING
>             IRQ_TYPE_EDGE_FALLING
>             IRQD_ACTIVATED
>             IRQD_IRQ_STARTED
> node:     0
> affinity: 0-3
> effectiv:
> domain:  :soc:spmi@fc4cf000:pm8941@0:gpios@c000
>  hwirq:   0x1
>  chip:    spmi-gpio
>   flags:   0x4
>              IRQCHIP_MASK_ON_SUSPEND
>  parent:
>     domain:  :soc:spmi@fc4cf000
>      hwirq:   0xc100057
>      chip:    pmic_arb
>       flags:   0x4
>                  IRQCHIP_MASK_ON_SUSPEND
> 
> Signed-off-by: Brian Masney <masneyb@onstation.org>
> Reviewed-by: Stephen Boyd <sboyd@kernel.org>
> ---
> Changes since v5:
> - Change IRQ_TYPE_NONE to IRQ_TYPE_EDGE_RISING
> 
> Changes since v4:
> - None
> 
> Changes since v3:
> - None
> 
> Changes since v2:
> - Use PMIC_GPIO_PHYSICAL_OFFSET instead of the 1 constant
> - Use gpiochip_irq_domain_{activate,deactivate}
> - Changed 'fwspec->param[0] + 0xc0 - 1' to 'hwirq + c0' in call to
>   irq_domain_alloc_irqs_parent
> 
> Changes since v1:
> - Use two cells for interrupts instead of four.
> - Pin numbers in interrupts-extended are now one based instead of zero
>   based so that they match the GPIO pin number.
> - Drop unnecessary parenthesis in pmic_gpio_domain_translate
> - Add missing of_node_put()
> - Remove irq field from pmic_gpio_pad struct that is no longer
>   necessary.
> 
>  drivers/pinctrl/qcom/pinctrl-spmi-gpio.c | 115 +++++++++++++++++++++--
>  1 file changed, 105 insertions(+), 10 deletions(-)

Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>

Thanks,

	M.

-- 
Jazz is not dead, it just smell funny.