linux-arm-msm.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Ard Biesheuvel <ard.biesheuvel@linaro.org>
To: Lee Jones <lee.jones@linaro.org>
Cc: alokc@codeaurora.org, Andy Gross <andy.gross@linaro.org>,
	David Brown <david.brown@linaro.org>,
	wsa+renesas@sang-engineering.com,
	Bjorn Andersson <bjorn.andersson@linaro.org>,
	Linus Walleij <linus.walleij@linaro.org>,
	balbi@kernel.org, Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
	Jeffrey Hugo <jlhugo@gmail.com>,
	linux-i2c <linux-i2c@vger.kernel.org>,
	linux-arm-msm <linux-arm-msm@vger.kernel.org>,
	"open list:GPIO SUBSYSTEM" <linux-gpio@vger.kernel.org>,
	linux-usb <linux-usb@vger.kernel.org>,
	linux-arm-kernel <linux-arm-kernel@lists.infradead.org>,
	Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH v3 4/8] pinctrl: qcom: sdm845: Provide ACPI support
Date: Mon, 10 Jun 2019 10:46:36 +0200	[thread overview]
Message-ID: <CAKv+Gu_s7i8JC4cv-dJMvm1_0cGzzhzf+Dxu0rxcF7iugF=vHg@mail.gmail.com> (raw)
In-Reply-To: <20190610084213.1052-4-lee.jones@linaro.org>

On Mon, 10 Jun 2019 at 10:42, Lee Jones <lee.jones@linaro.org> wrote:
>
> This patch provides basic support for booting with ACPI instead
> of the currently supported Device Tree.  When doing so there are a
> couple of differences which we need to taken into consideration.
>
> Firstly, the SDM850 ACPI tables omit information pertaining to the
> 4 reserved GPIOs on the platform.  If Linux attempts to touch/
> initialise any of these lines, the firmware will restart the
> platform.
>
> Secondly, when booting with ACPI, it is expected that the firmware
> will set-up things like; Regulators, Clocks, Pin Functions, etc in
> their ideal configuration.  Thus, the possible Pin Functions
> available to this platform are not advertised when providing the
> higher GPIOD/Pinctrl APIs with pin information.
>
> Signed-off-by: Lee Jones <lee.jones@linaro.org>

For the ACPI probing boilerplate:
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>

*However*, I really don't like hardcoding reserved GPIOs like this.
What guarantee do we have that each and every ACPI system
incorporating the QCOM0217 device has the exact same list of reserved
GPIOs?

> ---
>  drivers/pinctrl/qcom/Kconfig          |  2 +-
>  drivers/pinctrl/qcom/pinctrl-sdm845.c | 36 ++++++++++++++++++++++++++-
>  2 files changed, 36 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/pinctrl/qcom/Kconfig b/drivers/pinctrl/qcom/Kconfig
> index 2e66ab72c10b..aafbe932424f 100644
> --- a/drivers/pinctrl/qcom/Kconfig
> +++ b/drivers/pinctrl/qcom/Kconfig
> @@ -168,7 +168,7 @@ config PINCTRL_SDM660
>
>  config PINCTRL_SDM845
>         tristate "Qualcomm Technologies Inc SDM845 pin controller driver"
> -       depends on GPIOLIB && OF
> +       depends on GPIOLIB && (OF || ACPI)
>         select PINCTRL_MSM
>         help
>           This is the pinctrl, pinmux, pinconf and gpiolib driver for the
> diff --git a/drivers/pinctrl/qcom/pinctrl-sdm845.c b/drivers/pinctrl/qcom/pinctrl-sdm845.c
> index c97f20fca5fd..98a438dba711 100644
> --- a/drivers/pinctrl/qcom/pinctrl-sdm845.c
> +++ b/drivers/pinctrl/qcom/pinctrl-sdm845.c
> @@ -3,6 +3,7 @@
>   * Copyright (c) 2016-2018, The Linux Foundation. All rights reserved.
>   */
>
> +#include <linux/acpi.h>
>  #include <linux/module.h>
>  #include <linux/of.h>
>  #include <linux/platform_device.h>
> @@ -1277,6 +1278,10 @@ static const struct msm_pingroup sdm845_groups[] = {
>         UFS_RESET(ufs_reset, 0x99f000),
>  };
>
> +static const int sdm845_acpi_reserved_gpios[] = {
> +       0, 1, 2, 3, 81, 82, 83, 84, -1
> +};
> +
>  static const struct msm_pinctrl_soc_data sdm845_pinctrl = {
>         .pins = sdm845_pins,
>         .npins = ARRAY_SIZE(sdm845_pins),
> @@ -1287,11 +1292,39 @@ static const struct msm_pinctrl_soc_data sdm845_pinctrl = {
>         .ngpios = 150,
>  };
>
> +static const struct msm_pinctrl_soc_data sdm845_acpi_pinctrl = {
> +       .pins = sdm845_pins,
> +       .npins = ARRAY_SIZE(sdm845_pins),
> +       .groups = sdm845_groups,
> +       .ngroups = ARRAY_SIZE(sdm845_groups),
> +       .reserved_gpios = sdm845_acpi_reserved_gpios,
> +       .ngpios = 150,
> +};
> +
>  static int sdm845_pinctrl_probe(struct platform_device *pdev)
>  {
> -       return msm_pinctrl_probe(pdev, &sdm845_pinctrl);
> +       int ret;
> +
> +       if (pdev->dev.of_node) {
> +               ret = msm_pinctrl_probe(pdev, &sdm845_pinctrl);
> +       } else if (has_acpi_companion(&pdev->dev)) {
> +               ret = msm_pinctrl_probe(pdev, &sdm845_acpi_pinctrl);
> +       } else {
> +               dev_err(&pdev->dev, "DT and ACPI disabled\n");
> +               return -EINVAL;
> +       }
> +
> +       return ret;
>  }
>
> +#if CONFIG_ACPI
> +static const struct acpi_device_id sdm845_pinctrl_acpi_match[] = {
> +       { "QCOM0217"},
> +       { },
> +};
> +MODULE_DEVICE_TABLE(acpi, sdm845_pinctrl_acpi_match);
> +#endif
> +
>  static const struct of_device_id sdm845_pinctrl_of_match[] = {
>         { .compatible = "qcom,sdm845-pinctrl", },
>         { },
> @@ -1302,6 +1335,7 @@ static struct platform_driver sdm845_pinctrl_driver = {
>                 .name = "sdm845-pinctrl",
>                 .pm = &msm_pinctrl_dev_pm_ops,
>                 .of_match_table = sdm845_pinctrl_of_match,
> +               .acpi_match_table = ACPI_PTR(sdm845_pinctrl_acpi_match),
>         },
>         .probe = sdm845_pinctrl_probe,
>         .remove = msm_pinctrl_remove,
> --
> 2.17.1
>

  reply	other threads:[~2019-06-10  8:46 UTC|newest]

Thread overview: 28+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-06-10  8:42 [PATCH v3 1/8] i2c: i2c-qcom-geni: Provide support for ACPI Lee Jones
2019-06-10  8:42 ` [PATCH v3 2/8] i2c: i2c-qcom-geni: Signify successful driver probe Lee Jones
2019-06-11 19:40   ` Bjorn Andersson
2019-06-10  8:42 ` [PATCH v3 3/8] pinctrl: msm: Add ability for drivers to supply a reserved GPIO list Lee Jones
2019-06-12  7:25   ` Linus Walleij
2019-06-10  8:42 ` [PATCH v3 4/8] pinctrl: qcom: sdm845: Provide ACPI support Lee Jones
2019-06-10  8:46   ` Ard Biesheuvel [this message]
2019-06-10  8:55     ` Lee Jones
2019-06-10  9:03       ` Ard Biesheuvel
2019-06-10  9:22         ` Lee Jones
2019-06-10 10:20           ` Ard Biesheuvel
2019-06-11 18:39           ` Bjorn Andersson
2019-06-12  7:18             ` Linus Walleij
2019-06-11 18:40   ` Bjorn Andersson
2019-06-10  8:42 ` [PATCH v3 5/8] soc: qcom: geni: Add support for ACPI Lee Jones
2019-06-10  8:47   ` Ard Biesheuvel
2019-06-10  8:42 ` [PATCH v3 6/8] usb: dwc3: qcom: Add support for booting with ACPI Lee Jones
2019-06-10  8:42 ` [PATCH v3 7/8] usb: dwc3: qcom: Start USB in 'host mode' on the SDM845 Lee Jones
2019-06-11 22:33   ` Bjorn Andersson
2019-06-12  5:57     ` Lee Jones
2019-06-10  8:42 ` [PATCH v3 8/8] usb: dwc3: qcom: Improve error handling Lee Jones
2019-06-10  8:44 ` [PATCH v3 1/8] i2c: i2c-qcom-geni: Provide support for ACPI Ard Biesheuvel
2019-06-12 10:34 ` Wolfram Sang
2019-06-12 10:40   ` Lee Jones
2019-06-12 10:44     ` Wolfram Sang
2019-06-13  8:52       ` Lee Jones
2019-06-13  8:52         ` Lee Jones
2019-06-13  9:19         ` Wolfram Sang

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to='CAKv+Gu_s7i8JC4cv-dJMvm1_0cGzzhzf+Dxu0rxcF7iugF=vHg@mail.gmail.com' \
    --to=ard.biesheuvel@linaro.org \
    --cc=alokc@codeaurora.org \
    --cc=andy.gross@linaro.org \
    --cc=balbi@kernel.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=david.brown@linaro.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=jlhugo@gmail.com \
    --cc=lee.jones@linaro.org \
    --cc=linus.walleij@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-i2c@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=wsa+renesas@sang-engineering.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).