Re: [PATCH 07/15] dt: thermal: tsens: Document interrupt support in tsens driver

[Rob Herring <robh@kernel.org>]

On Fri, Aug 16, 2019 at 5:02 PM Amit Kucheria <amit.kucheria@linaro.org> wrote:
>
> On Sat, Aug 17, 2019 at 3:06 AM Rob Herring <robh@kernel.org> wrote:
> >
> > On Fri, Jul 26, 2019 at 03:48:42AM +0530, Amit Kucheria wrote:
> > > Define two new required properties to define interrupts and
> > > interrupt-names for tsens.
> > >
> > > Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> > > ---
> > >  Documentation/devicetree/bindings/thermal/qcom-tsens.txt | 5 +++++
> > >  1 file changed, 5 insertions(+)
> > >
> > > diff --git a/Documentation/devicetree/bindings/thermal/qcom-tsens.txt b/Documentation/devicetree/bindings/thermal/qcom-tsens.txt
> > > index 673cc1831ee9..3d3dd5dc6d36 100644
> > > --- a/Documentation/devicetree/bindings/thermal/qcom-tsens.txt
> > > +++ b/Documentation/devicetree/bindings/thermal/qcom-tsens.txt
> > > @@ -22,6 +22,8 @@ Required properties:
> > >
> > >  - #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description.
> > >  - #qcom,sensors: Number of sensors in tsens block
> > > +- interrupts: Interrupts generated from Always-On subsystem (AOSS)
> > > +- interrupt-names: The name of the interrupt e.g. "tsens0", "tsens1"
> >
> > How many interrupts? A name with just indices isn't too useful.
>
> Depending on the version of the tsens IP, there can be 1 (upper/lower
> threshold), 2 (upper/lower + critical threshold) or 3 (upper/lower +
> critical + zero degree) interrupts. This patch series only introduces
> support for a single interrupt (upper/lower).

I would expect a different compatible for each possibility.

> I used the names tsens0, tsens1 to encapsulate the controller instance
> since some SoCs have 1 controller, others have two. So we'll end up
> with something like the following in DT:

That's not really how *-names is supposed to work. The name is for
identifying what is at each index. Or to put it another way, a driver
should be able to use platform_get_irq_by_name(). So 'critical',
'zero' and something for the first one.

> tsens0: thermal-sensor@c263000 {
>                         compatible = "qcom,sdm845-tsens", "qcom,tsens-v2";
>                         reg = <0 0x0c263000 0 0x1ff>, /* TM */
>                               <0 0x0c222000 0 0x1ff>; /* SROT */
>                         #qcom,sensors = <13>;
>                         interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>,
>                                      <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>;
>                         interrupt-names = "tsens0", "tsens0-critical";
>                         #thermal-sensor-cells = <1>;
> };
>
> tsens1: thermal-sensor@c265000 {
>                         compatible = "qcom,sdm845-tsens", "qcom,tsens-v2";
>                         reg = <0 0x0c265000 0 0x1ff>, /* TM */
>                               <0 0x0c223000 0 0x1ff>; /* SROT */
>                         #qcom,sensors = <8>;
>                         interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>,
>                                      <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>;
>                         interrupt-names = "tsens1", "tsens1-critical";
>                         #thermal-sensor-cells = <1>;
> }
>
> Does that work?
>
> Regards,
> Amit
>
> > >  - Refer to Documentation/devicetree/bindings/nvmem/nvmem.txt to know how to specify
> > >  nvmem cells
> > >
> > > @@ -40,6 +42,9 @@ tsens0: thermal-sensor@c263000 {
> > >               reg = <0xc263000 0x1ff>, /* TM */
> > >                       <0xc222000 0x1ff>; /* SROT */
> > >               #qcom,sensors = <13>;
> > > +             interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>;
> > > +             interrupt-names = "tsens0";
> > > +
> > >               #thermal-sensor-cells = <1>;
> > >       };
> > >
> > > --
> > > 2.17.1
> > >