Re: [PATCH v2 1/3] Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6750

[Matthias Kaehlcke <mka@chromium.org>]

On Tue, Apr 20, 2021 at 09:56:48PM +0530, Venkata Lakshmi Narayana Gubba wrote:
> Added regulators,GPIOs and changes required to power on/off wcn6750.
> Added support for firmware download for wcn6750.
> 
> Changes done in detail:
> 1. Added regulators and corresponding current values.
> 2. Added sw_ctrl GPIO pin which is output from BT SoC and indicates
>    status of clock supply to BT SoC.
> 3. Added inline function to check if the SoC type is wcn399x or wcn6750.
> 4. Modified the function qca_wcn3990_init() to support wcn6750 and
>    renamed it to qca_regulator_init().
> 5. Added BT_ON and BT_OFF macros.
> 6. Added support to download mbn type firmware image as wcn6750 supports
>    mbn type image.
> 7. If mbn type image is not present then we will check for tlv type image.
> 8. Moved extracting rom version info to common place as this code is
>    common in all if else ladder in qca_uart_setup.
> 
> Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
> ---
>  drivers/bluetooth/btqca.c   |  88 ++++++++++++++++++++++++++----------
>  drivers/bluetooth/btqca.h   |  15 ++++++-
>  drivers/bluetooth/hci_qca.c | 106 ++++++++++++++++++++++++++++++++++----------
>  3 files changed, 161 insertions(+), 48 deletions(-)
> 
> diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
> index 25114f0..eec391a 100644
> --- a/drivers/bluetooth/btqca.c
> +++ b/drivers/bluetooth/btqca.c
> @@ -182,7 +182,8 @@ int qca_send_pre_shutdown_cmd(struct hci_dev *hdev)
>  }
>  EXPORT_SYMBOL_GPL(qca_send_pre_shutdown_cmd);
>  
> -static void qca_tlv_check_data(struct qca_fw_config *config,
> +static void qca_tlv_check_data(struct hci_dev *hdev,
> +			       struct qca_fw_config *config,
>  		const struct firmware *fw, enum qca_btsoc_type soc_type)
>  {
>  	const u8 *data;
> @@ -194,19 +195,21 @@ static void qca_tlv_check_data(struct qca_fw_config *config,
>  	struct tlv_type_nvm *tlv_nvm;
>  	uint8_t nvm_baud_rate = config->user_baud_rate;
>  
> -	tlv = (struct tlv_type_hdr *)fw->data;
> -
> -	type_len = le32_to_cpu(tlv->type_len);
> -	length = (type_len >> 8) & 0x00ffffff;
> -
> -	BT_DBG("TLV Type\t\t : 0x%x", type_len & 0x000000ff);
> -	BT_DBG("Length\t\t : %d bytes", length);
> -
>  	config->dnld_mode = QCA_SKIP_EVT_NONE;
>  	config->dnld_type = QCA_SKIP_EVT_NONE;
>  
>  	switch (config->type) {
> +	case ELF_TYPE_PATCH:
> +		config->dnld_mode = QCA_SKIP_EVT_VSE_CC;
> +		config->dnld_type = QCA_SKIP_EVT_VSE_CC;
> +
> +		bt_dev_dbg(hdev, "File Class        : 0x%x", fw->data[4]);
> +		bt_dev_dbg(hdev, "Data Encoding     : 0x%x", fw->data[5]);
> +		bt_dev_dbg(hdev, "File version      : 0x%x", fw->data[6]);
> +		break;
>  	case TLV_TYPE_PATCH:
> +		tlv = (struct tlv_type_hdr *)fw->data;
> +		type_len = le32_to_cpu(tlv->type_len);
>  		tlv_patch = (struct tlv_type_patch *)tlv->data;
>  
>  		/* For Rome version 1.1 to 3.1, all segment commands
> @@ -218,6 +221,7 @@ static void qca_tlv_check_data(struct qca_fw_config *config,
>  		config->dnld_mode = tlv_patch->download_mode;
>  		config->dnld_type = config->dnld_mode;
>  
> +		BT_DBG("TLV Type\t\t : 0x%x", type_len & 0x000000ff);
>  		BT_DBG("Total Length           : %d bytes",
>  		       le32_to_cpu(tlv_patch->total_size));
>  		BT_DBG("Patch Data Length      : %d bytes",
> @@ -243,6 +247,14 @@ static void qca_tlv_check_data(struct qca_fw_config *config,
>  		break;
>  
>  	case TLV_TYPE_NVM:
> +		tlv = (struct tlv_type_hdr *)fw->data;
> +
> +		type_len = le32_to_cpu(tlv->type_len);
> +		length = (type_len >> 8) & 0x00ffffff;
> +
> +		BT_DBG("TLV Type\t\t : 0x%x", type_len & 0x000000ff);
> +		BT_DBG("Length\t\t : %d bytes", length);
> +

To keep the wcn6750 shorther you could consider to have a separate patch
for the ELF type and the additional logging.

>  		idx = 0;
>  		data = tlv->data;
>  		while (idx < length) {
> @@ -387,7 +399,8 @@ static int qca_inject_cmd_complete_event(struct hci_dev *hdev)
>  
>  static int qca_download_firmware(struct hci_dev *hdev,
>  				 struct qca_fw_config *config,
> -				 enum qca_btsoc_type soc_type)
> +				 enum qca_btsoc_type soc_type,
> +				 u8 rom_ver)
>  {
>  	const struct firmware *fw;
>  	const u8 *segment;
> @@ -397,12 +410,29 @@ static int qca_download_firmware(struct hci_dev *hdev,
>  
>  	ret = request_firmware(&fw, config->fwname, &hdev->dev);
>  	if (ret) {
> -		bt_dev_err(hdev, "QCA Failed to request file: %s (%d)",
> -			   config->fwname, ret);
> -		return ret;
> +		/* For WCN6750, if mbn file is not present then check for
> +		 * tlv file.
> +		 */
> +		if (soc_type == QCA_WCN6750 && config->type == ELF_TYPE_PATCH) {
> +			bt_dev_dbg(hdev, "QCA Failed to request file: %s (%d)",
> +				   config->fwname, ret);
> +			config->type = TLV_TYPE_PATCH;
> +			snprintf(config->fwname, sizeof(config->fwname),
> +				 "qca/msbtfw%02x.tlv", rom_ver);
> +			ret = request_firmware(&fw, config->fwname, &hdev->dev);
> +			if (ret) {
> +				bt_dev_err(hdev, "QCA Failed to request file: %s (%d)",
> +					   config->fwname, ret);
> +				return ret;
> +			}
> +		} else {
> +			bt_dev_err(hdev, "QCA Failed to request file: %s (%d)",
> +				   config->fwname, ret);
> +			return ret;
> +		}
>  	}
>  
> -	qca_tlv_check_data(config, fw, soc_type);
> +	qca_tlv_check_data(hdev, config, fw, soc_type);
>  
>  	segment = fw->data;
>  	remain = fw->size;
> @@ -502,27 +532,33 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>  
>  	config.user_baud_rate = baudrate;
>  
> +	/* Firmware files to download are based on ROM version.
> +	 * ROM version is derived from last two bytes of soc_ver.
> +	 */
> +	rom_ver = ((soc_ver & 0x00000f00) >> 0x04) |
> +		    (soc_ver & 0x0000000f);
> +

This refactoring could also be done in a separate patch.

>  	/* Download rampatch file */
>  	config.type = TLV_TYPE_PATCH;
>  	if (qca_is_wcn399x(soc_type)) {
> -		/* Firmware files to download are based on ROM version.
> -		 * ROM version is derived from last two bytes of soc_ver.
> -		 */
> -		rom_ver = ((soc_ver & 0x00000f00) >> 0x04) |
> -			    (soc_ver & 0x0000000f);
>  		snprintf(config.fwname, sizeof(config.fwname),
>  			 "qca/crbtfw%02x.tlv", rom_ver);
>  	} else if (soc_type == QCA_QCA6390) {
> -		rom_ver = ((soc_ver & 0x00000f00) >> 0x04) |
> -			    (soc_ver & 0x0000000f);
>  		snprintf(config.fwname, sizeof(config.fwname),
>  			 "qca/htbtfw%02x.tlv", rom_ver);
> +	} else if (soc_type == QCA_WCN6750) {
> +		/* Choose mbn file by default.If mbn file is not found
> +		 * then choose tlv file
> +		 */
> +		config.type = ELF_TYPE_PATCH;
> +		snprintf(config.fwname, sizeof(config.fwname),
> +			 "qca/msbtfw%02x.mbn", rom_ver);
>  	} else {
>  		snprintf(config.fwname, sizeof(config.fwname),
>  			 "qca/rampatch_%08x.bin", soc_ver);
>  	}
>  
> -	err = qca_download_firmware(hdev, &config, soc_type);
> +	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
>  	if (err < 0) {
>  		bt_dev_err(hdev, "QCA Failed to download patch (%d)", err);
>  		return err;
> @@ -548,11 +584,14 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>  	else if (soc_type == QCA_QCA6390)
>  		snprintf(config.fwname, sizeof(config.fwname),
>  			 "qca/htnv%02x.bin", rom_ver);
> +	else if (soc_type == QCA_WCN6750)
> +		snprintf(config.fwname, sizeof(config.fwname),
> +			 "qca/msnv%02x.bin", rom_ver);
>  	else
>  		snprintf(config.fwname, sizeof(config.fwname),
>  			 "qca/nvm_%08x.bin", soc_ver);
>  
> -	err = qca_download_firmware(hdev, &config, soc_type);
> +	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
>  	if (err < 0) {
>  		bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
>  		return err;
> @@ -564,13 +603,14 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>  			return err;
>  	}
>  
> -	/* WCN399x supports the Microsoft vendor extension with 0xFD70 as the
> +	/* WCN399x and WCN6750 supports the Microsoft vendor extension with 0xFD70 as the
>  	 * VsMsftOpCode.
>  	 */
>  	switch (soc_type) {
>  	case QCA_WCN3990:
>  	case QCA_WCN3991:
>  	case QCA_WCN3998:
> +	case QCA_WCN6750:
>  		hci_set_msft_opcode(hdev, 0xFD70);
>  		break;
>  	default:
> diff --git a/drivers/bluetooth/btqca.h b/drivers/bluetooth/btqca.h
> index b19add7..3057bf8 100644
> --- a/drivers/bluetooth/btqca.h
> +++ b/drivers/bluetooth/btqca.h
> @@ -80,7 +80,8 @@ enum qca_tlv_dnld_mode {
>  
>  enum qca_tlv_type {
>  	TLV_TYPE_PATCH = 1,
> -	TLV_TYPE_NVM
> +	TLV_TYPE_NVM,
> +	ELF_TYPE_PATCH
>  };
>  
>  struct qca_fw_config {
> @@ -143,6 +144,7 @@ enum qca_btsoc_type {
>  	QCA_WCN3998,
>  	QCA_WCN3991,
>  	QCA_QCA6390,
> +	QCA_WCN6750
>  };
>  
>  #if IS_ENABLED(CONFIG_BT_QCA)
> @@ -160,6 +162,12 @@ static inline bool qca_is_wcn399x(enum qca_btsoc_type soc_type)
>  	return soc_type == QCA_WCN3990 || soc_type == QCA_WCN3991 ||
>  	       soc_type == QCA_WCN3998;
>  }
> +static inline bool qca_is_wcn399x_wcn6750(enum qca_btsoc_type soc_type)
> +{
> +	return soc_type == QCA_WCN3990 || soc_type == QCA_WCN3991 ||
> +	       soc_type == QCA_WCN3998 || soc_type == QCA_WCN6750;
> +}
> +

I anticipate that this would eventually need to be extended to
'qca_is_wcn399x_wcn6750_wcn1234', 'qca_is_wcn399x_wcn6750_wcn1234_wcn9876',
which isn't really practical. It might be better to just have 'qca_is_wcn399x()'
and 'qca_is_wcn6750()' (or qca_is_wcn675x() if applicable)

IMO

  if (qca_is_wcn399x(type) || qca_is_wcn6750(type))

isn't really worse than

  if (qca_is_wcn399x_wcn6750(type))


personally I find the formwer even easier to read.

>  #else
>  
>  static inline int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdaddr)
> @@ -192,6 +200,11 @@ static inline bool qca_is_wcn399x(enum qca_btsoc_type soc_type)
>  	return false;
>  }
>  
> +static inline bool qca_is_wcn399x_wcn6750(enum qca_btsoc_type soc_type)
> +{
> +	return false;
> +}
> +
>  static inline int qca_send_pre_shutdown_cmd(struct hci_dev *hdev)
>  {
>  	return -EOPNOTSUPP;
> diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
> index 0a00569..0d25ba9 100644
> --- a/drivers/bluetooth/hci_qca.c
> +++ b/drivers/bluetooth/hci_qca.c
> @@ -70,6 +70,10 @@
>  #define QCA_CRASHBYTE_PACKET_LEN	1096
>  #define QCA_MEMDUMP_BYTE		0xFB
>  
> +/* BT_EN GPIO enable/disable */
> +#define BT_ON		1
> +#define BT_OFF		0

These aren't really needed, passing 0 and 1 to gpio_set_value() is clear enough.

> +
>  enum qca_flags {
>  	QCA_IBS_DISABLED,
>  	QCA_DROP_VENDOR_EVENT,
> @@ -218,6 +222,7 @@ struct qca_power {
>  struct qca_serdev {
>  	struct hci_uart	 serdev_hu;
>  	struct gpio_desc *bt_en;
> +	struct gpio_desc *sw_ctrl;
>  	struct clk	 *susclk;
>  	enum qca_btsoc_type btsoc_type;
>  	struct qca_power *bt_power;
> @@ -604,7 +609,7 @@ static int qca_open(struct hci_uart *hu)
>  	if (hu->serdev) {
>  		qcadev = serdev_device_get_drvdata(hu->serdev);
>  
> -		if (qca_is_wcn399x(qcadev->btsoc_type))
> +		if (qca_is_wcn399x_wcn6750(qcadev->btsoc_type))
>  			hu->init_speed = qcadev->init_speed;
>  
>  		if (qcadev->oper_speed)
> @@ -1308,7 +1313,7 @@ static int qca_set_baudrate(struct hci_dev *hdev, uint8_t baudrate)
>  		      msecs_to_jiffies(CMD_TRANS_TIMEOUT_MS));
>  
>  	/* Give the controller time to process the request */
> -	if (qca_is_wcn399x(qca_soc_type(hu)))
> +	if (qca_is_wcn399x_wcn6750(qca_soc_type(hu)))
>  		usleep_range(1000, 10000);
>  	else
>  		msleep(300);
> @@ -1384,7 +1389,7 @@ static unsigned int qca_get_speed(struct hci_uart *hu,
>  
>  static int qca_check_speeds(struct hci_uart *hu)
>  {
> -	if (qca_is_wcn399x(qca_soc_type(hu))) {
> +	if (qca_is_wcn399x_wcn6750(qca_soc_type(hu))) {
>  		if (!qca_get_speed(hu, QCA_INIT_SPEED) &&
>  		    !qca_get_speed(hu, QCA_OPER_SPEED))
>  			return -EINVAL;
> @@ -1417,7 +1422,7 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
>  		/* Disable flow control for wcn3990 to deassert RTS while
>  		 * changing the baudrate of chip and host.
>  		 */
> -		if (qca_is_wcn399x(soc_type))
> +		if (qca_is_wcn399x_wcn6750(soc_type))
>  			hci_uart_set_flow_control(hu, true);
>  
>  		if (soc_type == QCA_WCN3990) {
> @@ -1434,7 +1439,7 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
>  		host_set_baudrate(hu, speed);
>  
>  error:
> -		if (qca_is_wcn399x(soc_type))
> +		if (qca_is_wcn399x_wcn6750(soc_type))
>  			hci_uart_set_flow_control(hu, false);
>  
>  		if (soc_type == QCA_WCN3990) {
> @@ -1585,10 +1590,12 @@ static bool qca_prevent_wake(struct hci_dev *hdev)
>  	return !wakeup;
>  }
>  
> -static int qca_wcn3990_init(struct hci_uart *hu)
> +static int qca_regulator_init(struct hci_uart *hu)
>  {
> +	enum qca_btsoc_type soc_type = qca_soc_type(hu);
>  	struct qca_serdev *qcadev;
>  	int ret;
> +	bool sw_ctrl_state;
>  
>  	/* Check for vregs status, may be hci down has turned
>  	 * off the voltage regulator.
> @@ -1607,16 +1614,31 @@ static int qca_wcn3990_init(struct hci_uart *hu)
>  		}
>  	}
>  
> -	/* Forcefully enable wcn3990 to enter in to boot mode. */
> -	host_set_baudrate(hu, 2400);
> -	ret = qca_send_power_pulse(hu, false);
> -	if (ret)
> -		return ret;
> +	if (qca_is_wcn399x(soc_type)) {
> +		/* Forcefully enable wcn3990 to enter in to boot mode. */

nit: s/wcn3990/wcn399x/ since you are already touching the code

> +		host_set_baudrate(hu, 2400);
> +		ret = qca_send_power_pulse(hu, false);
> +		if (ret)
> +			return ret;
> +	}
> +
> +	/* For wcn6750 need to enable gpio bt_en */

Does this really only apply to the wcn6750()?

From the code it's evident that the enable pin is togged, I suggest
to drop the comment.

> +	if (qcadev->bt_en) {
> +		gpiod_set_value_cansleep(qcadev->bt_en, BT_OFF);
> +		msleep(50);
> +		gpiod_set_value_cansleep(qcadev->bt_en, BT_ON);
> +		msleep(50);
> +		sw_ctrl_state = gpiod_get_value_cansleep(qcadev->sw_ctrl);
> +		bt_dev_dbg(hu->hdev, "SW_CTRL is %d", sw_ctrl_state);

Need to check if 'sw_ctrl' is a valid GPIO?

What exactly is the role of 'SW_CTRL'?

> +	}
>  
>  	qca_set_speed(hu, QCA_INIT_SPEED);
> -	ret = qca_send_power_pulse(hu, true);
> -	if (ret)
> -		return ret;
> +
> +	if (qca_is_wcn399x(soc_type)) {
> +		ret = qca_send_power_pulse(hu, true);
> +		if (ret)
> +			return ret;
> +	}
>  
>  	/* Now the device is in ready state to communicate with host.
>  	 * To sync host with device we need to reopen port.
> @@ -1649,12 +1671,12 @@ static int qca_power_on(struct hci_dev *hdev)
>  	if (!hu->serdev)
>  		return 0;
>  
> -	if (qca_is_wcn399x(soc_type)) {
> -		ret = qca_wcn3990_init(hu);
> +	if (qca_is_wcn399x_wcn6750(soc_type)) {
> +		ret = qca_regulator_init(hu);
>  	} else {
>  		qcadev = serdev_device_get_drvdata(hu->serdev);
>  		if (qcadev->bt_en) {
> -			gpiod_set_value_cansleep(qcadev->bt_en, 1);
> +			gpiod_set_value_cansleep(qcadev->bt_en, BT_ON);
>  			/* Controller needs time to bootup. */
>  			msleep(150);
>  		}
> @@ -1689,7 +1711,8 @@ static int qca_setup(struct hci_uart *hu)
>  	set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
>  
>  	bt_dev_info(hdev, "setting up %s",
> -		qca_is_wcn399x(soc_type) ? "wcn399x" : "ROME/QCA6390");
> +		qca_is_wcn399x(soc_type) ? "wcn399x" :
> +		(soc_type == QCA_WCN6750) ? "wcn6750" : "ROME/QCA6390");
>  
>  	qca->memdump_state = QCA_MEMDUMP_IDLE;
>  
> @@ -1700,7 +1723,7 @@ static int qca_setup(struct hci_uart *hu)
>  
>  	clear_bit(QCA_SSR_TRIGGERED, &qca->flags);
>  
> -	if (qca_is_wcn399x(soc_type)) {
> +	if (qca_is_wcn399x_wcn6750(soc_type)) {
>  		set_bit(HCI_QUIRK_USE_BDADDR_PROPERTY, &hdev->quirks);
>  
>  		ret = qca_read_soc_version(hdev, &ver, soc_type);
> @@ -1720,7 +1743,7 @@ static int qca_setup(struct hci_uart *hu)
>  		qca_baudrate = qca_get_baudrate_value(speed);
>  	}
>  
> -	if (!qca_is_wcn399x(soc_type)) {
> +	if (!qca_is_wcn399x_wcn6750(soc_type)) {
>  		/* Get QCA version information */
>  		ret = qca_read_soc_version(hdev, &ver, soc_type);
>  		if (ret)
> @@ -1828,12 +1851,30 @@ static const struct qca_device_data qca_soc_data_qca6390 = {
>  	.num_vregs = 0,
>  };
>  
> +static const struct qca_device_data qca_soc_data_wcn6750 = {
> +	.soc_type = QCA_WCN6750,
> +	.vregs = (struct qca_vreg []) {
> +		{ "vddio", 5000 },
> +		{ "vddaon", 26000 },
> +		{ "vddbtcxmx", 126000 },
> +		{ "vddrfacmn", 12500 },
> +		{ "vddrfa0p8", 102000 },
> +		{ "vddrfa1p7", 302000 },
> +		{ "vddrfa1p2", 257000 },
> +		{ "vddrfa2p2", 1700000 },
> +		{ "vddasd", 200 },
> +	},
> +	.num_vregs = 9,
> +	.capabilities = QCA_CAP_WIDEBAND_SPEECH | QCA_CAP_VALID_LE_STATES,
> +};
> +
>  static void qca_power_shutdown(struct hci_uart *hu)
>  {
>  	struct qca_serdev *qcadev;
>  	struct qca_data *qca = hu->priv;
>  	unsigned long flags;
>  	enum qca_btsoc_type soc_type = qca_soc_type(hu);
> +	bool sw_ctrl_state;
>  
>  	qcadev = serdev_device_get_drvdata(hu->serdev);
>  
> @@ -1856,8 +1897,14 @@ static void qca_power_shutdown(struct hci_uart *hu)
>  		host_set_baudrate(hu, 2400);
>  		qca_send_power_pulse(hu, false);
>  		qca_regulator_disable(qcadev);
> +	} else if (soc_type == QCA_WCN6750) {
> +		gpiod_set_value_cansleep(qcadev->bt_en, BT_OFF);
> +		msleep(100);
> +		qca_regulator_disable(qcadev);
> +		sw_ctrl_state = gpiod_get_value_cansleep(qcadev->sw_ctrl);
> +		bt_dev_dbg(hu->hdev, "SW_CTRL is %d", sw_ctrl_state);
>  	} else if (qcadev->bt_en) {
> -		gpiod_set_value_cansleep(qcadev->bt_en, 0);
> +		gpiod_set_value_cansleep(qcadev->bt_en, BT_OFF);
>  	}
>  
>  	set_bit(QCA_BT_OFF, &qca->flags);
> @@ -1978,7 +2025,7 @@ static int qca_serdev_probe(struct serdev_device *serdev)
>  	if (!qcadev->oper_speed)
>  		BT_DBG("UART will pick default operating speed");
>  
> -	if (data && qca_is_wcn399x(data->soc_type)) {
> +	if (data && qca_is_wcn399x_wcn6750(data->soc_type)) {
>  		qcadev->btsoc_type = data->soc_type;
>  		qcadev->bt_power = devm_kzalloc(&serdev->dev,
>  						sizeof(struct qca_power),
> @@ -1996,6 +2043,18 @@ static int qca_serdev_probe(struct serdev_device *serdev)
>  
>  		qcadev->bt_power->vregs_on = false;
>  
> +		qcadev->bt_en = devm_gpiod_get_optional(&serdev->dev, "enable",
> +					       GPIOD_OUT_LOW);
> +		if (!qcadev->bt_en && data->soc_type == QCA_WCN6750) {
> +			dev_err(&serdev->dev, "failed to acquire BT_EN gpio\n");
> +			power_ctrl_enabled = false;
> +		}
> +
> +		qcadev->sw_ctrl = devm_gpiod_get_optional(&serdev->dev, "swctrl",
> +					       GPIOD_IN);
> +		if (!qcadev->sw_ctrl && data->soc_type == QCA_WCN6750)
> +			dev_warn(&serdev->dev, "failed to acquire SW_CTRL gpio\n");
> +
>  		qcadev->susclk = devm_clk_get_optional(&serdev->dev, NULL);
>  		if (IS_ERR(qcadev->susclk)) {
>  			dev_err(&serdev->dev, "failed to acquire clk\n");
> @@ -2068,7 +2127,7 @@ static void qca_serdev_remove(struct serdev_device *serdev)
>  	struct qca_serdev *qcadev = serdev_device_get_drvdata(serdev);
>  	struct qca_power *power = qcadev->bt_power;
>  
> -	if (qca_is_wcn399x(qcadev->btsoc_type) && power->vregs_on)
> +	if (qca_is_wcn399x_wcn6750(qcadev->btsoc_type) && power->vregs_on)
>  		qca_power_shutdown(&qcadev->serdev_hu);
>  	else if (qcadev->susclk)
>  		clk_disable_unprepare(qcadev->susclk);
> @@ -2244,6 +2303,7 @@ static const struct of_device_id qca_bluetooth_of_match[] = {
>  	{ .compatible = "qcom,wcn3990-bt", .data = &qca_soc_data_wcn3990},
>  	{ .compatible = "qcom,wcn3991-bt", .data = &qca_soc_data_wcn3991},
>  	{ .compatible = "qcom,wcn3998-bt", .data = &qca_soc_data_wcn3998},
> +	{ .compatible = "qcom,wcn6750-bt", .data = &qca_soc_data_wcn6750},
>  	{ /* sentinel */ }
>  };
>  MODULE_DEVICE_TABLE(of, qca_bluetooth_of_match);
> -- 
> QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
> of Code Aurora Forum, hosted by The Linux Foundation
>