Re: [PATCH V3 1/3] arm64: dts: sc7280: Add QSPI node

[Bjorn Andersson <bjorn.andersson@linaro.org>]

On Fri 04 Jun 08:54 CDT 2021, Roja Rani Yarubandi wrote:

> Add QSPI DT node for SC7280 SoC.
> 
> Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
> ---
> Changes in V3:
>  - Broken the huge V2 patch into 3 smaller patches.
>    1. QSPI DT nodes
>    2. QUP wrapper_0 DT nodes
>    3. QUP wrapper_1 DT nodes
> 
> Changes in V2:
>  - As per Doug's comments removed pinmux/pinconf subnodes.
>  - As per Doug's comments split of SPI, UART nodes has been done.
>  - Moved QSPI node before aps_smmu as per the order.
> 
>  arch/arm64/boot/dts/qcom/sc7280-idp.dts | 29 ++++++++++++
>  arch/arm64/boot/dts/qcom/sc7280.dtsi    | 61 +++++++++++++++++++++++++
>  2 files changed, 90 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> index 3900cfc09562..d0edffc15736 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> @@ -268,6 +268,22 @@ pmr735b_die_temp {
>  		};
>  };
>  
> +&qspi {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data01>;
> +
> +	flash@0 {
> +		compatible = "jedec,spi-nor";
> +		reg = <0>;
> +
> +		/* TODO: Increase frequency after testing */
> +		spi-max-frequency = <25000000>;
> +		spi-tx-bus-width = <2>;
> +		spi-rx-bus-width = <2>;
> +	};
> +};
> +
>  &qupv3_id_0 {
>  	status = "okay";
>  };
> @@ -278,6 +294,19 @@ &uart5 {
>  
>  /* PINCTRL - additions to nodes defined in sc7280.dtsi */
>  
> +&qspi_cs0 {
> +	bias-disable;
> +};
> +
> +&qspi_clk {
> +	bias-disable;
> +};
> +
> +&qspi_data01 {
> +	/* High-Z when no transfers; nice to park the lines */
> +	bias-pull-up;
> +};
> +
>  &qup_uart5_default {
>  	tx {
>  		pins = "gpio46";
> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> index 6c9d5eb93f93..3047ab802cd2 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> @@ -1061,6 +1061,42 @@ apss_merge_funnel_in: endpoint {
>  			};
>  		};
>  
> +		qspi_opp_table: qspi-opp-table {

This node doesn't represents anything on the mmio bus, so it shouldn't
live in in /soc. Can't you move it into &qspi?

Regards,
Bjorn

> +			compatible = "operating-points-v2";
> +
> +			opp-75000000 {
> +				opp-hz = /bits/ 64 <75000000>;
> +				required-opps = <&rpmhpd_opp_low_svs>;
> +			};
> +
> +			opp-150000000 {
> +				opp-hz = /bits/ 64 <150000000>;
> +				required-opps = <&rpmhpd_opp_svs>;
> +			};
> +
> +			opp-300000000 {
> +				opp-hz = /bits/ 64 <300000000>;
> +				required-opps = <&rpmhpd_opp_nom>;
> +			};
> +		};
> +
> +		qspi: spi@88dc000 {
> +			compatible = "qcom,qspi-v1";
> +			reg = <0 0x088dc000 0 0x1000>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
> +				 <&gcc GCC_QSPI_CORE_CLK>;
> +			clock-names = "iface", "core";
> +			interconnects = <&gem_noc MASTER_APPSS_PROC 0
> +					&cnoc2 SLAVE_QSPI_0 0>;
> +			interconnect-names = "qspi-config";
> +			power-domains = <&rpmhpd SC7280_CX>;
> +			operating-points-v2 = <&qspi_opp_table>;
> +			status = "disabled";
> +		};