From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Konrad Dybcio <konrad.dybcio@somainline.org>
Cc: ~postmarketos/upstreaming@lists.sr.ht,
martin.botka@somainline.org,
angelogioacchino.delregno@somainline.org,
marijn.suijten@somainline.org, jamipkettunen@somainline.org,
Andy Gross <agross@kernel.org>,
Linus Walleij <linus.walleij@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
linux-arm-msm@vger.kernel.org, linux-gpio@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH v4 1/2] dt-bindings: pinctrl: qcom: Add bindings for MDM9607
Date: Thu, 24 Jun 2021 15:31:46 -0500 [thread overview]
Message-ID: <YNTrsqJEoTHVjF9S@yoga> (raw)
In-Reply-To: <20210624191743.617073-1-konrad.dybcio@somainline.org>
On Thu 24 Jun 14:17 CDT 2021, Konrad Dybcio wrote:
> Document the newly added MDM9607 pinctrl driver.
>
> Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Regards,
Bjorn
> ---
> Changes since v3:
> - Use the correct compatible in the example
>
> .../pinctrl/qcom,mdm9607-pinctrl.yaml | 133 ++++++++++++++++++
> 1 file changed, 133 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,mdm9607-pinctrl.yaml
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,mdm9607-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9607-pinctrl.yaml
> new file mode 100644
> index 000000000000..3b02dc6626ed
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9607-pinctrl.yaml
> @@ -0,0 +1,133 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/qcom,mdm9607-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm Technologies, Inc. MDM9607 TLMM block
> +
> +maintainers:
> + - Konrad Dybcio <konrad.dybcio@somainline.org>
> +
> +description: |
> + This binding describes the Top Level Mode Multiplexer block found in the
> + MDM9607 platform.
> +
> +allOf:
> + - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
> +
> +properties:
> + compatible:
> + const: qcom,mdm9607-tlmm
> +
> + reg:
> + maxItems: 1
> +
> + interrupts: true
> + interrupt-controller: true
> + '#interrupt-cells': true
> + gpio-controller: true
> + gpio-reserved-ranges: true
> + '#gpio-cells': true
> + gpio-ranges: true
> + wakeup-parent: true
> +
> +required:
> + - compatible
> + - reg
> +
> +additionalProperties: false
> +
> +patternProperties:
> + '-state$':
> + oneOf:
> + - $ref: "#/$defs/qcom-mdm9607-tlmm-state"
> + - patternProperties:
> + ".*":
> + $ref: "#/$defs/qcom-mdm9607-tlmm-state"
> +
> +'$defs':
> + qcom-mdm9607-tlmm-state:
> + type: object
> + description:
> + Pinctrl node's client devices use subnodes for desired pin configuration.
> + Client device subnodes use below standard properties.
> + $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state"
> +
> + properties:
> + pins:
> + description:
> + List of gpio pins affected by the properties specified in this
> + subnode.
> + items:
> + oneOf:
> + - pattern: "^gpio([1-9]|[1-7][0-9]|80)$"
> + - enum: [ sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd,
> + sdc2_data, qdsd_cmd, qdsd_data0, qdsd_data1, qdsd_data2,
> + qdsd_data3 ]
> + minItems: 1
> + maxItems: 16
> +
> + function:
> + description:
> + Specify the alternative function to be configured for the specified
> + pins.
> +
> + enum: [ adsp_ext, atest_bbrx0, atest_bbrx1, atest_char, atest_char0,
> + atest_char1, atest_char2, atest_char3,
> + atest_combodac_to_gpio_native, atest_gpsadc_dtest0_native,
> + atest_gpsadc_dtest1_native, atest_tsens, backlight_en_b,
> + bimc_dte0, bimc_dte1, blsp1_spi, blsp2_spi, blsp3_spi,
> + blsp_i2c1, blsp_i2c2, blsp_i2c3, blsp_i2c4, blsp_i2c5,
> + blsp_i2c6, blsp_spi1, blsp_spi2, blsp_spi3, blsp_spi4,
> + blsp_spi5, blsp_spi6, blsp_uart1, blsp_uart2, blsp_uart3,
> + blsp_uart4, blsp_uart5, blsp_uart6, blsp_uim1, blsp_uim2,
> + codec_int, codec_rst, coex_uart, cri_trng, cri_trng0,
> + cri_trng1, dbg_out, ebi0_wrcdc, ebi2_a, ebi2_a_d_8_b,
> + ebi2_lcd, ebi2_lcd_cs_n_b, ebi2_lcd_te_b, eth_irq, eth_rst,
> + gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a, gcc_gp2_clk_b,
> + gcc_gp3_clk_a, gcc_gp3_clk_b, gcc_plltest, gcc_tlmm, gmac_mdio,
> + gpio, gsm0_tx, lcd_rst, ldo_en, ldo_update, m_voc, modem_tsync,
> + nav_ptp_pps_in_a, nav_ptp_pps_in_b, nav_tsync_out_a,
> + nav_tsync_out_b, pa_indicator, pbs0, pbs1, pbs2,
> + pri_mi2s_data0_a, pri_mi2s_data1_a, pri_mi2s_mclk_a,
> + pri_mi2s_sck_a, pri_mi2s_ws_a, prng_rosc, ptp_pps_out_a,
> + ptp_pps_out_b, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
> + pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a,
> + pwr_nav_enabled_b, qdss_cti_trig_in_a0, qdss_cti_trig_in_a1,
> + qdss_cti_trig_in_b0, qdss_cti_trig_in_b1, qdss_cti_trig_out_a0,
> + qdss_cti_trig_out_a1, qdss_cti_trig_out_b0, qdss_cti_trig_out_b1,
> + qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a,
> + qdss_tracectl_b, qdss_tracedata_a, qdss_tracedata_b, rcm_marker1,
> + rcm_marker2, sd_write, sec_mi2s, sensor_en, sensor_int2,
> + sensor_int3, sensor_rst, ssbi1, ssbi2, touch_rst, ts_int,
> + uim1_clk, uim1_data, uim1_present, uim1_reset, uim2_clk,
> + uim2_data, uim2_present, uim2_reset, uim_batt, wlan_en1, ]
> +
> + bias-disable: true
> + bias-pull-down: true
> + bias-pull-up: true
> + drive-strength: true
> + input-enable: true
> + output-high: true
> + output-low: true
> +
> + required:
> + - pins
> + - function
> +
> + additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + tlmm: pinctrl@1000000 {
> + compatible = "qcom,mdm9607-tlmm";
> + reg = <0x01000000 0x300000>;
> + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> + gpio-controller;
> + gpio-ranges = <&msmgpio 0 0 80>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> --
> 2.32.0
>
next prev parent reply other threads:[~2021-06-24 20:31 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-06-24 19:17 [PATCH v4 1/2] dt-bindings: pinctrl: qcom: Add bindings for MDM9607 Konrad Dybcio
2021-06-24 19:17 ` [PATCH v4 2/2] pinctrl: qcom: Add MDM9607 pinctrl driver Konrad Dybcio
2021-07-23 15:45 ` Linus Walleij
2021-06-24 20:11 ` [PATCH v4 1/2] dt-bindings: pinctrl: qcom: Add bindings for MDM9607 Rob Herring
2021-06-24 20:31 ` Bjorn Andersson [this message]
2021-07-23 15:44 ` Linus Walleij
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=YNTrsqJEoTHVjF9S@yoga \
--to=bjorn.andersson@linaro.org \
--cc=agross@kernel.org \
--cc=angelogioacchino.delregno@somainline.org \
--cc=devicetree@vger.kernel.org \
--cc=jamipkettunen@somainline.org \
--cc=konrad.dybcio@somainline.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=marijn.suijten@somainline.org \
--cc=martin.botka@somainline.org \
--cc=robh+dt@kernel.org \
--cc=~postmarketos/upstreaming@lists.sr.ht \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).