linux-arm-msm.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH v4 0/3] Add Qualcomm Technologies, Inc. PM8008 MFD driver
@ 2021-05-11  0:27 Guru Das Srinagesh
  2021-05-11  0:27 ` [PATCH v4 1/3] dt-bindings: mfd: pm8008: Add IRQ listing Guru Das Srinagesh
                   ` (3 more replies)
  0 siblings, 4 replies; 6+ messages in thread
From: Guru Das Srinagesh @ 2021-05-11  0:27 UTC (permalink / raw)
  To: Lee Jones, Rob Herring, devicetree
  Cc: Mark Brown, linux-arm-msm, Bjorn Andersson, linux-kernel,
	Guru Das Srinagesh

Changes from v3:
  - Addressed Lee's comments. 
  - This patchset is still based on regmap.git's for-next branch as my
    regmap-irq changes have not yet landed in mfd.git for-mfd-next or
    for-mfd-next-next (please advise which branch to use in this regard).

Changes from v2:
  - Collected Rob Herring's Acked-by for the IRQ listing patch
  - Addressed Rob's comments for the dt-bindings patch

Changes from v1:
  - Removed errant Change-Id from dt-bindings IRQ patch and gathered Bjorn's
    Reviewed-by
  - Fixed up YAML errors using make dt_binding_check

This driver is dependent on changes that have been made to the regmap-irq
framework that have currently been accepted [1][2] in regmap.git upstream by
Mark Brown but haven't made it to Linus' tree yet. For this reason, this driver
has been based on the tip of regmap.git and not mfd.git.

Those changes, and this driver, are the result of a rewrite effort that was
promised a long ago [3]. The framework changes and this driver have been tested
and verified end-to-end on an internal platform.

[1] https://lore.kernel.org/lkml/20210318183607.gFxO2hoTO274vl3jUuxWbi19rq9wQELzN-y3B4jvO10@z/
[2] https://lore.kernel.org/lkml/161726943419.2413.4844313396830856637.b4-ty@kernel.org/
[3] https://lore.kernel.org/lkml/20200519185757.GA13992@codeaurora.org/


Guru Das Srinagesh (3):
  dt-bindings: mfd: pm8008: Add IRQ listing
  dt-bindings: mfd: pm8008: Add bindings
  mfd: pm8008: Add driver for QCOM PM8008 PMIC

 .../devicetree/bindings/mfd/qcom,pm8008.yaml       | 121 ++++++++++
 drivers/mfd/Kconfig                                |  14 ++
 drivers/mfd/Makefile                               |   1 +
 drivers/mfd/qcom-pm8008.c                          | 260 +++++++++++++++++++++
 include/dt-bindings/mfd/qcom-pm8008.h              |  19 ++
 5 files changed, 415 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/qcom,pm8008.yaml
 create mode 100644 drivers/mfd/qcom-pm8008.c
 create mode 100644 include/dt-bindings/mfd/qcom-pm8008.h

-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project


^ permalink raw reply	[flat|nested] 6+ messages in thread

* [PATCH v4 1/3] dt-bindings: mfd: pm8008: Add IRQ listing
  2021-05-11  0:27 [PATCH v4 0/3] Add Qualcomm Technologies, Inc. PM8008 MFD driver Guru Das Srinagesh
@ 2021-05-11  0:27 ` Guru Das Srinagesh
  2021-05-11  0:27 ` [PATCH v4 2/3] dt-bindings: mfd: pm8008: Add bindings Guru Das Srinagesh
                   ` (2 subsequent siblings)
  3 siblings, 0 replies; 6+ messages in thread
From: Guru Das Srinagesh @ 2021-05-11  0:27 UTC (permalink / raw)
  To: Lee Jones, Rob Herring, devicetree
  Cc: Mark Brown, linux-arm-msm, Bjorn Andersson, linux-kernel,
	Guru Das Srinagesh

Add a header file listing all of the IRQs that Qualcomm Technologies,
Inc. PM8008 supports. The constants defined in this file may be used in
the client device tree node to specify interrupts.

Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
---
 include/dt-bindings/mfd/qcom-pm8008.h | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
 create mode 100644 include/dt-bindings/mfd/qcom-pm8008.h

diff --git a/include/dt-bindings/mfd/qcom-pm8008.h b/include/dt-bindings/mfd/qcom-pm8008.h
new file mode 100644
index 0000000..eca9448
--- /dev/null
+++ b/include/dt-bindings/mfd/qcom-pm8008.h
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2021 The Linux Foundation. All rights reserved.
+ */
+
+#ifndef __DT_BINDINGS_MFD_QCOM_PM8008_H
+#define __DT_BINDINGS_MFD_QCOM_PM8008_H
+
+/* PM8008 IRQ numbers */
+#define PM8008_IRQ_MISC_UVLO	0
+#define PM8008_IRQ_MISC_OVLO	1
+#define PM8008_IRQ_MISC_OTST2	2
+#define PM8008_IRQ_MISC_OTST3	3
+#define PM8008_IRQ_MISC_LDO_OCP	4
+#define PM8008_IRQ_TEMP_ALARM	5
+#define PM8008_IRQ_GPIO1	6
+#define PM8008_IRQ_GPIO2	7
+
+#endif
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project


^ permalink raw reply	[flat|nested] 6+ messages in thread

* [PATCH v4 2/3] dt-bindings: mfd: pm8008: Add bindings
  2021-05-11  0:27 [PATCH v4 0/3] Add Qualcomm Technologies, Inc. PM8008 MFD driver Guru Das Srinagesh
  2021-05-11  0:27 ` [PATCH v4 1/3] dt-bindings: mfd: pm8008: Add IRQ listing Guru Das Srinagesh
@ 2021-05-11  0:27 ` Guru Das Srinagesh
  2021-05-11  0:40   ` Guru Das Srinagesh
  2021-05-11  0:27 ` [PATCH v4 3/3] mfd: pm8008: Add driver for QCOM PM8008 PMIC Guru Das Srinagesh
  2021-05-21  0:04 ` [PATCH v4 0/3] Add Qualcomm Technologies, Inc. PM8008 MFD driver Guru Das Srinagesh
  3 siblings, 1 reply; 6+ messages in thread
From: Guru Das Srinagesh @ 2021-05-11  0:27 UTC (permalink / raw)
  To: Lee Jones, Rob Herring, devicetree
  Cc: Mark Brown, linux-arm-msm, Bjorn Andersson, linux-kernel,
	Guru Das Srinagesh

Add bindings for the Qualcomm Technologies, Inc. PM8008 MFD driver.

Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
---
 .../devicetree/bindings/mfd/qcom,pm8008.yaml       | 121 +++++++++++++++++++++
 1 file changed, 121 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/qcom,pm8008.yaml

diff --git a/Documentation/devicetree/bindings/mfd/qcom,pm8008.yaml b/Documentation/devicetree/bindings/mfd/qcom,pm8008.yaml
new file mode 100644
index 0000000..7799368
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/qcom,pm8008.yaml
@@ -0,0 +1,121 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/qcom,pm8008.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies, Inc. PM8008 PMIC bindings
+
+maintainers:
+  - Guru Das Srinagesh <gurus@codeaurora.org>
+
+description: |
+  Qualcomm Technologies, Inc. PM8008 is a dedicated camera PMIC that integrates
+  all the necessary power management, housekeeping, and interface support
+  functions into a single IC.
+
+properties:
+  compatible:
+    const: qcom,pm8008
+
+  reg:
+    description:
+      I2C slave address.
+
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+    description: Parent interrupt.
+
+  "#interrupt-cells":
+    const: 2
+
+    description: |
+      The first cell is the IRQ number, the second cell is the IRQ trigger
+      flag. All interrupts are listed in include/dt-bindings/mfd/qcom-pm8008.h.
+
+  interrupt-controller: true
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+patternProperties:
+  "^gpio@[0-9a-f]+$":
+    type: object
+
+    description: |
+      The GPIO peripheral. This node may be specified twice, one for each GPIO.
+
+    properties:
+      compatible:
+        const: qcom,pm8008-gpio
+
+      reg:
+        description: Peripheral address of one of the two GPIO peripherals.
+        maxItems: 1
+
+      gpio-controller: true
+
+      interrupt-controller: true
+
+      "#interrupt-cells":
+        const: 2
+
+      "#gpio-cells":
+        const: 2
+
+    required:
+      - compatible
+      - reg
+      - gpio-controller
+      - interrupt-controller
+      - "#gpio-cells"
+      - "#interrupt-cells"
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - "#address-cells"
+  - "#size-cells"
+  - "#interrupt-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/mfd/qcom-pm8008.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    qupv3_se13_i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      pm8008i@8 {
+        compatible = "qcom,pm8008";
+        reg = <0x8>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+        interrupt-controller;
+        #interrupt-cells = <2>;
+
+        interrupt-parent = <&tlmm>;
+        interrupts = <32 IRQ_TYPE_EDGE_RISING>;
+
+        gpio@c000 {
+          compatible = "qcom,pm8008-gpio";
+          reg = <0xc000>;
+          gpio-controller;
+          #gpio-cells = <2>;
+          interrupt-controller;
+          #interrupt-cells = <2>;
+        };
+      };
+    };
+
+...
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project


^ permalink raw reply	[flat|nested] 6+ messages in thread

* [PATCH v4 3/3] mfd: pm8008: Add driver for QCOM PM8008 PMIC
  2021-05-11  0:27 [PATCH v4 0/3] Add Qualcomm Technologies, Inc. PM8008 MFD driver Guru Das Srinagesh
  2021-05-11  0:27 ` [PATCH v4 1/3] dt-bindings: mfd: pm8008: Add IRQ listing Guru Das Srinagesh
  2021-05-11  0:27 ` [PATCH v4 2/3] dt-bindings: mfd: pm8008: Add bindings Guru Das Srinagesh
@ 2021-05-11  0:27 ` Guru Das Srinagesh
  2021-05-21  0:04 ` [PATCH v4 0/3] Add Qualcomm Technologies, Inc. PM8008 MFD driver Guru Das Srinagesh
  3 siblings, 0 replies; 6+ messages in thread
From: Guru Das Srinagesh @ 2021-05-11  0:27 UTC (permalink / raw)
  To: Lee Jones, Rob Herring, devicetree
  Cc: Mark Brown, linux-arm-msm, Bjorn Andersson, linux-kernel,
	Guru Das Srinagesh

Qualcomm Technologies, Inc. PM8008 is a dedicated camera PMIC that
integrates all the necessary power management, housekeeping, and
interface support functions into a single IC. Its key features include
overtemperature protection, low-dropout linear regulators, GPIOs, and an
I2C interface.

Add an MFD driver to support it.

Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
---
 drivers/mfd/Kconfig       |  14 +++
 drivers/mfd/Makefile      |   1 +
 drivers/mfd/qcom-pm8008.c | 260 ++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 275 insertions(+)
 create mode 100644 drivers/mfd/qcom-pm8008.c

diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index b74efa4..c3bb49a 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -2087,6 +2087,20 @@ config MFD_ACER_A500_EC
 	  The controller itself is ENE KB930, it is running firmware
 	  customized for the specific needs of the Acer A500 hardware.
 
+config MFD_QCOM_PM8008
+	tristate "QCOM PM8008 Power Management IC"
+	depends on I2C && OF
+	select REGMAP_I2C
+	select REGMAP_IRQ
+	help
+	  Select this option to get support for the Qualcomm Technologies, Inc.
+	  PM8008 PMIC chip. PM8008 is a dedicated camera PMIC that integrates
+	  all the necessary power management, housekeeping, and interface
+	  support functions into a single IC. This driver provides common
+	  support for accessing the device by instantiating all the child nodes
+	  under it in the device tree. Additional drivers must be enabled in
+	  order to use the functionality of the device.
+
 menu "Multimedia Capabilities Port drivers"
 	depends on ARCH_SA1100
 
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 834f546..a5dda823 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -264,6 +264,7 @@ obj-$(CONFIG_MFD_ROHM_BD718XX)	+= rohm-bd718x7.o
 obj-$(CONFIG_MFD_STMFX) 	+= stmfx.o
 obj-$(CONFIG_MFD_KHADAS_MCU) 	+= khadas-mcu.o
 obj-$(CONFIG_MFD_ACER_A500_EC)	+= acer-ec-a500.o
+obj-$(CONFIG_MFD_QCOM_PM8008)	+= qcom-pm8008.o
 
 obj-$(CONFIG_SGI_MFD_IOC3)	+= ioc3.o
 obj-$(CONFIG_MFD_SIMPLE_MFD_I2C)	+= simple-mfd-i2c.o
diff --git a/drivers/mfd/qcom-pm8008.c b/drivers/mfd/qcom-pm8008.c
new file mode 100644
index 0000000..c472d7f
--- /dev/null
+++ b/drivers/mfd/qcom-pm8008.c
@@ -0,0 +1,260 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/bitops.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/of_platform.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+#include <dt-bindings/mfd/qcom-pm8008.h>
+
+#define I2C_INTR_STATUS_BASE		0x0550
+#define INT_RT_STS_OFFSET		0x10
+#define INT_SET_TYPE_OFFSET		0x11
+#define INT_POL_HIGH_OFFSET		0x12
+#define INT_POL_LOW_OFFSET		0x13
+#define INT_LATCHED_CLR_OFFSET		0x14
+#define INT_EN_SET_OFFSET		0x15
+#define INT_EN_CLR_OFFSET		0x16
+#define INT_LATCHED_STS_OFFSET		0x18
+
+enum {
+	PM8008_MISC,
+	PM8008_TEMP_ALARM,
+	PM8008_GPIO1,
+	PM8008_GPIO2,
+	PM8008_NUM_PERIPHS,
+};
+
+#define PM8008_PERIPH_0_BASE	0x900
+#define PM8008_PERIPH_1_BASE	0x2400
+#define PM8008_PERIPH_2_BASE	0xC000
+#define PM8008_PERIPH_3_BASE	0xC100
+
+#define PM8008_TEMP_ALARM_ADDR	PM8008_PERIPH_1_BASE
+#define PM8008_GPIO1_ADDR	PM8008_PERIPH_2_BASE
+#define PM8008_GPIO2_ADDR	PM8008_PERIPH_3_BASE
+
+#define PM8008_STATUS_BASE	(PM8008_PERIPH_0_BASE | INT_LATCHED_STS_OFFSET)
+#define PM8008_MASK_BASE	(PM8008_PERIPH_0_BASE | INT_EN_SET_OFFSET)
+#define PM8008_UNMASK_BASE	(PM8008_PERIPH_0_BASE | INT_EN_CLR_OFFSET)
+#define PM8008_TYPE_BASE	(PM8008_PERIPH_0_BASE | INT_SET_TYPE_OFFSET)
+#define PM8008_ACK_BASE		(PM8008_PERIPH_0_BASE | INT_LATCHED_CLR_OFFSET)
+#define PM8008_POLARITY_HI_BASE	(PM8008_PERIPH_0_BASE | INT_POL_HIGH_OFFSET)
+#define PM8008_POLARITY_LO_BASE	(PM8008_PERIPH_0_BASE | INT_POL_LOW_OFFSET)
+
+#define PM8008_PERIPH_OFFSET(paddr)	(paddr - PM8008_PERIPH_0_BASE)
+
+struct pm8008_data {
+	struct device *dev;
+	struct regmap *regmap;
+	int irq;
+	struct regmap_irq_chip_data *irq_data;
+};
+
+static unsigned int p0_offs[] = {PM8008_PERIPH_OFFSET(PM8008_PERIPH_0_BASE)};
+static unsigned int p1_offs[] = {PM8008_PERIPH_OFFSET(PM8008_PERIPH_1_BASE)};
+static unsigned int p2_offs[] = {PM8008_PERIPH_OFFSET(PM8008_PERIPH_2_BASE)};
+static unsigned int p3_offs[] = {PM8008_PERIPH_OFFSET(PM8008_PERIPH_3_BASE)};
+
+static struct regmap_irq_sub_irq_map pm8008_sub_reg_offsets[] = {
+	REGMAP_IRQ_MAIN_REG_OFFSET(p0_offs),
+	REGMAP_IRQ_MAIN_REG_OFFSET(p1_offs),
+	REGMAP_IRQ_MAIN_REG_OFFSET(p2_offs),
+	REGMAP_IRQ_MAIN_REG_OFFSET(p3_offs),
+};
+
+static unsigned int pm8008_virt_regs[] = {
+	PM8008_POLARITY_HI_BASE,
+	PM8008_POLARITY_LO_BASE,
+};
+
+enum {
+	POLARITY_HI_INDEX,
+	POLARITY_LO_INDEX,
+	PM8008_NUM_VIRT_REGS,
+};
+
+static struct regmap_irq pm8008_irqs[] = {
+	REGMAP_IRQ_REG(PM8008_IRQ_MISC_UVLO,	PM8008_MISC,	BIT(0)),
+	REGMAP_IRQ_REG(PM8008_IRQ_MISC_OVLO,	PM8008_MISC,	BIT(1)),
+	REGMAP_IRQ_REG(PM8008_IRQ_MISC_OTST2,	PM8008_MISC,	BIT(2)),
+	REGMAP_IRQ_REG(PM8008_IRQ_MISC_OTST3,	PM8008_MISC,	BIT(3)),
+	REGMAP_IRQ_REG(PM8008_IRQ_MISC_LDO_OCP,	PM8008_MISC,	BIT(4)),
+	REGMAP_IRQ_REG(PM8008_IRQ_TEMP_ALARM,	PM8008_TEMP_ALARM, BIT(0)),
+	REGMAP_IRQ_REG(PM8008_IRQ_GPIO1,	PM8008_GPIO1,	BIT(0)),
+	REGMAP_IRQ_REG(PM8008_IRQ_GPIO2,	PM8008_GPIO2,	BIT(0)),
+};
+
+static int pm8008_set_type_virt(unsigned int **virt_buf,
+				      unsigned int type, unsigned long hwirq,
+				      int reg)
+{
+	switch (type) {
+	case IRQ_TYPE_EDGE_FALLING:
+	case IRQ_TYPE_LEVEL_LOW:
+		virt_buf[POLARITY_HI_INDEX][reg] &= ~pm8008_irqs[hwirq].mask;
+		virt_buf[POLARITY_LO_INDEX][reg] |= pm8008_irqs[hwirq].mask;
+		break;
+
+	case IRQ_TYPE_EDGE_RISING:
+	case IRQ_TYPE_LEVEL_HIGH:
+		virt_buf[POLARITY_HI_INDEX][reg] |= pm8008_irqs[hwirq].mask;
+		virt_buf[POLARITY_LO_INDEX][reg] &= ~pm8008_irqs[hwirq].mask;
+		break;
+
+	case IRQ_TYPE_EDGE_BOTH:
+		virt_buf[POLARITY_HI_INDEX][reg] |= pm8008_irqs[hwirq].mask;
+		virt_buf[POLARITY_LO_INDEX][reg] |= pm8008_irqs[hwirq].mask;
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static struct regmap_irq_chip pm8008_irq_chip = {
+	.name			= "pm8008_irq",
+	.main_status		= I2C_INTR_STATUS_BASE,
+	.num_main_regs		= 1,
+	.num_virt_regs		= PM8008_NUM_VIRT_REGS,
+	.irqs			= pm8008_irqs,
+	.num_irqs		= ARRAY_SIZE(pm8008_irqs),
+	.num_regs		= PM8008_NUM_PERIPHS,
+	.not_fixed_stride	= true,
+	.sub_reg_offsets	= pm8008_sub_reg_offsets,
+	.set_type_virt		= pm8008_set_type_virt,
+	.status_base		= PM8008_STATUS_BASE,
+	.mask_base		= PM8008_MASK_BASE,
+	.unmask_base		= PM8008_UNMASK_BASE,
+	.type_base		= PM8008_TYPE_BASE,
+	.ack_base		= PM8008_ACK_BASE,
+	.virt_reg_base		= pm8008_virt_regs,
+	.num_type_reg		= PM8008_NUM_PERIPHS,
+};
+
+static struct regmap_config qcom_mfd_regmap_cfg = {
+	.reg_bits	= 16,
+	.val_bits	= 8,
+	.max_register	= 0xFFFF,
+};
+
+static int pm8008_init(struct pm8008_data *chip)
+{
+	int rc;
+
+	/*
+	 * Set TEMP_ALARM peripheral's TYPE so that the regmap-irq framework
+	 * reads this as the default value instead of zero, the HW default.
+	 * This is required to enable the writing of TYPE registers in
+	 * regmap_irq_sync_unlock().
+	 */
+	rc = regmap_write(chip->regmap,
+			 (PM8008_TEMP_ALARM_ADDR | INT_SET_TYPE_OFFSET),
+			 BIT(0));
+	if (rc)
+		return rc;
+
+	/* Do the same for GPIO1 and GPIO2 peripherals */
+	rc = regmap_write(chip->regmap,
+			 (PM8008_GPIO1_ADDR | INT_SET_TYPE_OFFSET), BIT(0));
+	if (rc)
+		return rc;
+
+	rc = regmap_write(chip->regmap,
+			 (PM8008_GPIO2_ADDR | INT_SET_TYPE_OFFSET), BIT(0));
+
+	return rc;
+}
+
+static int pm8008_probe_irq_peripherals(struct pm8008_data *chip,
+					int client_irq)
+{
+	int rc, i;
+	struct regmap_irq_type *type;
+	struct regmap_irq_chip_data *irq_data;
+
+	rc = pm8008_init(chip);
+	if (rc) {
+		dev_err(chip->dev, "Init failed: %d\n", rc);
+		return rc;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(pm8008_irqs); i++) {
+		type = &pm8008_irqs[i].type;
+
+		type->type_reg_offset	  = pm8008_irqs[i].reg_offset;
+		type->type_rising_val	  = pm8008_irqs[i].mask;
+		type->type_falling_val	  = pm8008_irqs[i].mask;
+		type->type_level_high_val = 0;
+		type->type_level_low_val  = 0;
+
+		if (type->type_reg_offset == PM8008_MISC)
+			type->types_supported = IRQ_TYPE_EDGE_RISING;
+		else
+			type->types_supported = (IRQ_TYPE_EDGE_BOTH |
+				IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW);
+	}
+
+	rc = devm_regmap_add_irq_chip(chip->dev, chip->regmap, client_irq,
+			IRQF_SHARED, 0, &pm8008_irq_chip, &irq_data);
+	if (rc) {
+		dev_err(chip->dev, "Failed to add IRQ chip: %d\n", rc);
+		return rc;
+	}
+
+	return 0;
+}
+
+static int pm8008_probe(struct i2c_client *client)
+{
+	int rc;
+	struct pm8008_data *chip;
+
+	chip = devm_kzalloc(&client->dev, sizeof(*chip), GFP_KERNEL);
+	if (!chip)
+		return -ENOMEM;
+
+	chip->dev = &client->dev;
+	chip->regmap = devm_regmap_init_i2c(client, &qcom_mfd_regmap_cfg);
+	if (!chip->regmap)
+		return -ENODEV;
+
+	i2c_set_clientdata(client, chip);
+
+	if (of_property_read_bool(chip->dev->of_node, "interrupt-controller")) {
+		rc = pm8008_probe_irq_peripherals(chip, client->irq);
+		if (rc)
+			dev_err(chip->dev, "Failed to probe irq periphs: %d\n", rc);
+	}
+
+	return devm_of_platform_populate(chip->dev);
+}
+
+static const struct of_device_id pm8008_match[] = {
+	{ .compatible = "qcom,pm8008", },
+	{ },
+};
+
+static struct i2c_driver pm8008_mfd_driver = {
+	.driver = {
+		.name = "pm8008",
+		.of_match_table = pm8008_match,
+	},
+	.probe_new = pm8008_probe,
+};
+module_i2c_driver(pm8008_mfd_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("i2c:qcom-pm8008");
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project


^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH v4 2/3] dt-bindings: mfd: pm8008: Add bindings
  2021-05-11  0:27 ` [PATCH v4 2/3] dt-bindings: mfd: pm8008: Add bindings Guru Das Srinagesh
@ 2021-05-11  0:40   ` Guru Das Srinagesh
  0 siblings, 0 replies; 6+ messages in thread
From: Guru Das Srinagesh @ 2021-05-11  0:40 UTC (permalink / raw)
  To: Lee Jones, Rob Herring, devicetree
  Cc: Mark Brown, linux-arm-msm, Bjorn Andersson, linux-kernel

On Mon, May 10, 2021 at 05:27:07PM -0700, Guru Das Srinagesh wrote:
> Add bindings for the Qualcomm Technologies, Inc. PM8008 MFD driver.
> 
> Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>

Forgot to add:

Reviewed-by: Rob Herring <robh@kernel.org>

I'll wait for comments on this patchset, and then collect this and push
it out in the next patchset.

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH v4 0/3] Add Qualcomm Technologies, Inc. PM8008 MFD driver
  2021-05-11  0:27 [PATCH v4 0/3] Add Qualcomm Technologies, Inc. PM8008 MFD driver Guru Das Srinagesh
                   ` (2 preceding siblings ...)
  2021-05-11  0:27 ` [PATCH v4 3/3] mfd: pm8008: Add driver for QCOM PM8008 PMIC Guru Das Srinagesh
@ 2021-05-21  0:04 ` Guru Das Srinagesh
  3 siblings, 0 replies; 6+ messages in thread
From: Guru Das Srinagesh @ 2021-05-21  0:04 UTC (permalink / raw)
  To: Lee Jones, Rob Herring, devicetree
  Cc: Mark Brown, linux-arm-msm, Bjorn Andersson, linux-kernel

On Mon, May 10, 2021 at 05:27:05PM -0700, Guru Das Srinagesh wrote:
> Changes from v3:
>   - Addressed Lee's comments. 
>   - This patchset is still based on regmap.git's for-next branch as my
>     regmap-irq changes have not yet landed in mfd.git for-mfd-next or
>     for-mfd-next-next (please advise which branch to use in this regard).
> 
> Changes from v2:
>   - Collected Rob Herring's Acked-by for the IRQ listing patch
>   - Addressed Rob's comments for the dt-bindings patch
> 
> Changes from v1:
>   - Removed errant Change-Id from dt-bindings IRQ patch and gathered Bjorn's
>     Reviewed-by
>   - Fixed up YAML errors using make dt_binding_check

Hi Lee,

Could you please review this patchset when you get a chance?

Thank you.

Guru Das.

^ permalink raw reply	[flat|nested] 6+ messages in thread

end of thread, other threads:[~2021-05-21  0:04 UTC | newest]

Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-05-11  0:27 [PATCH v4 0/3] Add Qualcomm Technologies, Inc. PM8008 MFD driver Guru Das Srinagesh
2021-05-11  0:27 ` [PATCH v4 1/3] dt-bindings: mfd: pm8008: Add IRQ listing Guru Das Srinagesh
2021-05-11  0:27 ` [PATCH v4 2/3] dt-bindings: mfd: pm8008: Add bindings Guru Das Srinagesh
2021-05-11  0:40   ` Guru Das Srinagesh
2021-05-11  0:27 ` [PATCH v4 3/3] mfd: pm8008: Add driver for QCOM PM8008 PMIC Guru Das Srinagesh
2021-05-21  0:04 ` [PATCH v4 0/3] Add Qualcomm Technologies, Inc. PM8008 MFD driver Guru Das Srinagesh

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).