Linux-Bluetooth Archive on lore.kernel.org
 help / Atom feed
From: Balakrishna Godavarthi <bgodavar@codeaurora.org>
To: Rocky Liao <rjliao@codeaurora.org>
Cc: robh+dt@kernel.org, mark.rutland@arm.com, marcel@holtmann.org,
	johan.hedberg@gmail.com, thierry.escande@linaro.org,
	netdev@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-bluetooth@vger.kernel.org,
	linux-arm-msm@vger.kernel.org, c-hbandi@codeaurora.org,
	Hemantg <hemantg@codeaurora.org>
Subject: Re: [PATCH v5 1/2] Bluetooth: hci_qca: Load customized NVM based on the device property
Date: Fri, 17 May 2019 08:13:57 +0530
Message-ID: <178d2a3454399cfad0e61e72a13ea19a@codeaurora.org> (raw)
In-Reply-To: <1557919161-11010-1-git-send-email-rjliao@codeaurora.org>

Hi Rocky,

On 2019-05-15 16:49, Rocky Liao wrote:
> QCA BTSOC NVM is a customized firmware file and different vendors may
> want to have different BTSOC configuration (e.g. Configure SCO over PCM
> or I2S, Setting Tx power, etc.) via this file. This patch will allow
> vendors to download different NVM firmware file by reading a device
> property "firmware-name".
> 
> Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
> ---
> Changes in v5:
>   * Made the change applicable to the wcn399x series chip sets
> ---
>  drivers/bluetooth/btqca.c   |  8 ++++++--
>  drivers/bluetooth/btqca.h   |  6 ++++--
>  drivers/bluetooth/hci_qca.c | 19 ++++++++++++++++++-
>  3 files changed, 28 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
> index cc12eec..a78b80e 100644
> --- a/drivers/bluetooth/btqca.c
> +++ b/drivers/bluetooth/btqca.c
> @@ -332,7 +332,8 @@ int qca_set_bdaddr_rome(struct hci_dev *hdev,
> const bdaddr_t *bdaddr)
>  EXPORT_SYMBOL_GPL(qca_set_bdaddr_rome);
> 
>  int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
> -		   enum qca_btsoc_type soc_type, u32 soc_ver)
> +		   enum qca_btsoc_type soc_type, u32 soc_ver,
> +		   const char *firmware_name)
>  {
>  	struct rome_config config;
>  	int err;
> @@ -365,7 +366,10 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t 
> baudrate,
> 
>  	/* Download NVM configuration */
>  	config.type = TLV_TYPE_NVM;
> -	if (qca_is_wcn399x(soc_type))
> +	if (firmware_name)
> +		snprintf(config.fwname, sizeof(config.fwname),
> +			 "qca/%s", firmware_name);
> +	else if (qca_is_wcn399x(soc_type))
>  		snprintf(config.fwname, sizeof(config.fwname),
>  			 "qca/crnv%02x.bin", rom_ver);
>  	else
> diff --git a/drivers/bluetooth/btqca.h b/drivers/bluetooth/btqca.h
> index 4c4fe2b..8c037bb 100644
> --- a/drivers/bluetooth/btqca.h
> +++ b/drivers/bluetooth/btqca.h
> @@ -140,7 +140,8 @@ enum qca_btsoc_type {
> 
>  int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdaddr);
>  int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
> -		   enum qca_btsoc_type soc_type, u32 soc_ver);
> +		   enum qca_btsoc_type soc_type, u32 soc_ver,
> +		   const char *firmware_name);
>  int qca_read_soc_version(struct hci_dev *hdev, u32 *soc_version);
>  int qca_set_bdaddr(struct hci_dev *hdev, const bdaddr_t *bdaddr);
>  static inline bool qca_is_wcn399x(enum qca_btsoc_type soc_type)
> @@ -155,7 +156,8 @@ static inline int qca_set_bdaddr_rome(struct
> hci_dev *hdev, const bdaddr_t *bdad
>  }
> 
>  static inline int qca_uart_setup(struct hci_dev *hdev, uint8_t 
> baudrate,
> -				 enum qca_btsoc_type soc_type, u32 soc_ver)
> +				 enum qca_btsoc_type soc_type, u32 soc_ver,
> +				 const char *firmware_name)
>  {
>  	return -EOPNOTSUPP;
>  }
> diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
> index 57322c4..9590602 100644
> --- a/drivers/bluetooth/hci_qca.c
> +++ b/drivers/bluetooth/hci_qca.c
> @@ -169,6 +169,7 @@ struct qca_serdev {
>  	struct qca_power *bt_power;
>  	u32 init_speed;
>  	u32 oper_speed;
> +	const char *firmware_name;
>  };
> 
>  static int qca_power_setup(struct hci_uart *hu, bool on);
> @@ -190,6 +191,17 @@ static enum qca_btsoc_type qca_soc_type(struct
> hci_uart *hu)
>  	return soc_type;
>  }
> 
> +static const char *qca_get_firmware_name(struct hci_uart *hu)
> +{
> +	if (hu->serdev) {
> +		struct qca_serdev *qsd = serdev_device_get_drvdata(hu->serdev);
> +
> +		return qsd->firmware_name;
> +	} else {
> +		return NULL;
> +	}
> +}
> +
>  static void __serial_clock_on(struct tty_struct *tty)
>  {
>  	/* TODO: Some chipset requires to enable UART clock on client
> @@ -1195,6 +1207,7 @@ static int qca_setup(struct hci_uart *hu)
>  	struct qca_data *qca = hu->priv;
>  	unsigned int speed, qca_baudrate = QCA_BAUDRATE_115200;
>  	enum qca_btsoc_type soc_type = qca_soc_type(hu);
> +	const char *firmware_name = qca_get_firmware_name(hu);
>  	int ret;
>  	int soc_ver = 0;
> 
> @@ -1245,7 +1258,8 @@ static int qca_setup(struct hci_uart *hu)
> 
>  	bt_dev_info(hdev, "QCA controller version 0x%08x", soc_ver);
>  	/* Setup patch / NVM configurations */
> -	ret = qca_uart_setup(hdev, qca_baudrate, soc_type, soc_ver);
> +	ret = qca_uart_setup(hdev, qca_baudrate, soc_type, soc_ver,
> +			firmware_name);
>  	if (!ret) {
>  		set_bit(QCA_IBS_ENABLED, &qca->flags);
>  		qca_debugfs_init(hdev);
> @@ -1477,6 +1491,9 @@ static int qca_serdev_probe(struct serdev_device 
> *serdev)
>  			return PTR_ERR(qcadev->bt_en);
>  		}
> 
> +		device_property_read_string(&serdev->dev, "firmware-name",
> +					 &qcadev->firmware_name);
> +
>  		qcadev->susclk = devm_clk_get(&serdev->dev, NULL);
>  		if (IS_ERR(qcadev->susclk)) {
>  			dev_err(&serdev->dev, "failed to acquire clk\n");

Thanks for doing it for wcn399x series too.

Change look fine to me.

Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
-- 
Regards
Balakrishna.

  reply index

Thread overview: 28+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-04-04  6:37 [PATCH] " Rocky Liao
2019-04-04  6:56 ` Balakrishna Godavarthi
2019-04-04  9:08 ` [PATCH v2 1/2] " Rocky Liao
2019-04-04  9:08   ` [PATCH v2 2/2] dt-bindings: net: bluetooth: Add device property nvm-postfix for QCA6174 Rocky Liao
2019-04-04 12:32     ` Marc Gonzalez
2019-04-09 10:15       ` Rocky Liao
2019-04-09 14:03         ` Rob Herring
2019-04-09 14:48           ` Rocky Liao
2019-04-09 13:54       ` Rob Herring
2019-04-10  9:27     ` [PATCH v3 2/2] dt-bindings: net: bluetooth: Add device property firmware-name " Rocky Liao
2019-04-23 17:06       ` Marcel Holtmann
2019-04-24  6:19         ` Rocky Liao
2019-04-26 17:45           ` Rob Herring
2019-04-27  5:59             ` Marcel Holtmann
2019-05-03  7:56               ` Rocky Liao
2019-05-05 17:32                 ` Marcel Holtmann
2019-04-26 20:50       ` Rob Herring
2019-05-12  3:19       ` [PATCH v4 " Rocky Liao
2019-05-13 15:31         ` Rob Herring
2019-05-15 11:20         ` [PATCH v5 " Rocky Liao
2019-04-04  9:59   ` [PATCH v2 1/2] Bluetooth: hci_qca: Load customized NVM based on the device property Balakrishna Godavarthi
2019-04-10  9:27   ` [PATCH v3 " Rocky Liao
2019-05-12  3:19     ` [PATCH v4 " Rocky Liao
2019-05-15  5:32       ` Balakrishna Godavarthi
2019-05-15  8:30         ` Rocky Liao
2019-05-15 11:19       ` [PATCH v5 " Rocky Liao
2019-05-17  2:43         ` Balakrishna Godavarthi [this message]
2019-05-17  4:26           ` Harish Bandi

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=178d2a3454399cfad0e61e72a13ea19a@codeaurora.org \
    --to=bgodavar@codeaurora.org \
    --cc=c-hbandi@codeaurora.org \
    --cc=devicetree@vger.kernel.org \
    --cc=hemantg@codeaurora.org \
    --cc=johan.hedberg@gmail.com \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-bluetooth@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=marcel@holtmann.org \
    --cc=mark.rutland@arm.com \
    --cc=netdev@vger.kernel.org \
    --cc=rjliao@codeaurora.org \
    --cc=robh+dt@kernel.org \
    --cc=thierry.escande@linaro.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-Bluetooth Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-bluetooth/0 linux-bluetooth/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-bluetooth linux-bluetooth/ https://lore.kernel.org/linux-bluetooth \
		linux-bluetooth@vger.kernel.org linux-bluetooth@archiver.kernel.org
	public-inbox-index linux-bluetooth


Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-bluetooth


AGPL code for this site: git clone https://public-inbox.org/ public-inbox