Linux-Bluetooth Archive on lore.kernel.org
 help / Atom feed
From: Balakrishna Godavarthi <bgodavar@codeaurora.org>
To: Matthias Kaehlcke <mka@chromium.org>
Cc: marcel@holtmann.org, johan.hedberg@gmail.com, johan@kernel.org,
	linux-kernel@vger.kernel.org, linux-bluetooth@vger.kernel.org,
	hemantg@codeaurora.org, linux-arm-msm@vger.kernel.org
Subject: Re: [PATCH v9 2/3] Bluetooth: hci_qca: Deassert RTS while baudrate change command
Date: Mon, 28 Jan 2019 19:15:48 +0530
Message-ID: <6b18e30fb1b747d674a75cb265b5821b@codeaurora.org> (raw)
In-Reply-To: <20190125001259.GB81583@google.com>

Hi Matthias,

On 2019-01-25 05:42, Matthias Kaehlcke wrote:
> Hi Balakrishna,
> 
> On Thu, Jan 24, 2019 at 05:38:07PM +0530, Balakrishna Godavarthi wrote:
>> This patch will help to stop frame reassembly errors while changing
>> the baudrate. This is because host send a change baudrate request
>> command to the chip with 115200 bps, Whereas chip will change their
>> UART clocks to the enable for new baudrate and sends the response
>> for the change request command with newer baudrate, On host side
>> we are still operating in 115200 bps which results of reading garbage
>> data. Here we are pulling RTS line, so that chip we will wait to send 
>> data
>> to host until host change its baudrate.
>> 
>> Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
>> Tested-by: Matthias Kaehlcke <mka@chromium.org>
>> Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
>> ---
>> Changes in v9:
>>  * disabled flow control while setting the baudrate of HOST and chip.
>> ---
>>  drivers/bluetooth/hci_qca.c | 24 +++++++++++++-----------
>>  1 file changed, 13 insertions(+), 11 deletions(-)
>> 
>> diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
>> index c08f4d105e73..6b5bcd44e24c 100644
>> --- a/drivers/bluetooth/hci_qca.c
>> +++ b/drivers/bluetooth/hci_qca.c
>> @@ -964,7 +964,6 @@ static int qca_set_baudrate(struct hci_dev *hdev, 
>> uint8_t baudrate)
>>  	struct hci_uart *hu = hci_get_drvdata(hdev);
>>  	struct qca_data *qca = hu->priv;
>>  	struct sk_buff *skb;
>> -	struct qca_serdev *qcadev;
>>  	u8 cmd[] = { 0x01, 0x48, 0xFC, 0x01, 0x00 };
>> 
>>  	if (baudrate > QCA_BAUDRATE_3200000)
>> @@ -978,13 +977,6 @@ static int qca_set_baudrate(struct hci_dev *hdev, 
>> uint8_t baudrate)
>>  		return -ENOMEM;
>>  	}
>> 
>> -	/* Disabling hardware flow control is mandatory while
>> -	 * sending change baudrate request to wcn3990 SoC.
>> -	 */
>> -	qcadev = serdev_device_get_drvdata(hu->serdev);
>> -	if (qcadev->btsoc_type == QCA_WCN3990)
>> -		hci_uart_set_flow_control(hu, true);
>> -
>>  	/* Assign commands to change baudrate and packet type. */
>>  	skb_put_data(skb, cmd, sizeof(cmd));
>>  	hci_skb_pkt_type(skb) = HCI_COMMAND_PKT;
>> @@ -1000,9 +992,6 @@ static int qca_set_baudrate(struct hci_dev *hdev, 
>> uint8_t baudrate)
>>  	schedule_timeout(msecs_to_jiffies(BAUDRATE_SETTLE_TIMEOUT_MS));
>>  	set_current_state(TASK_RUNNING);
>> 
>> -	if (qcadev->btsoc_type == QCA_WCN3990)
>> -		hci_uart_set_flow_control(hu, false);
>> -
>>  	return 0;
>>  }
>> 
>> @@ -1089,6 +1078,7 @@ static int qca_check_speeds(struct hci_uart *hu)
>>  static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type 
>> speed_type)
>>  {
>>  	unsigned int speed, qca_baudrate;
>> +	struct qca_serdev *qcadev;
>>  	int ret;
>> 
>>  	if (speed_type == QCA_INIT_SPEED) {
>> @@ -1100,6 +1090,15 @@ static int qca_set_speed(struct hci_uart *hu, 
>> enum qca_speed_type speed_type)
>>  		if (!speed)
>>  			return 0;
>> 
>> +		/* Deassert RTS while changing the baudrate of chip and host.
>> +		 * This will prevent chip from transmitting its response with
>> +		 * the new baudrate while the host port is still operating at
>> +		 * the old speed.
>> +		 */
> 
> It is not necessarily evident which action deasserts RTS, I suggest to
> rephrase it to something like:
> 
> "Disable flow control for wcn3990 to deassert RTS while ... "
> 

[Bala]: will update.

>> +		qcadev = serdev_device_get_drvdata(hu->serdev);
>> +		if (qcadev->btsoc_type == QCA_WCN3990)
>> +			hci_uart_set_flow_control(hu, true);
>> +
>>  		qca_baudrate = qca_get_baudrate_value(speed);
>>  		bt_dev_dbg(hu->hdev, "Set UART speed to %d", speed);
>>  		ret = qca_set_baudrate(hu->hdev, qca_baudrate);
> 
> flow control should be re-enabled in the error path.
> 
> Cheers
> 
> Matthias

[Bala; will update.

-- 
Regards
Balakrishna.

  reply index

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-01-24 12:08 [PATCH v9 0/3] Bug fixes for Qualcomm BT chip wcn3990 Balakrishna Godavarthi
2019-01-24 12:08 ` [PATCH v9 1/3] Bluetooth: hci_qca: use wait_until_sent() for power pulses Balakrishna Godavarthi
2019-01-25  1:14   ` Matthias Kaehlcke
2019-01-28 13:49     ` Balakrishna Godavarthi
2019-01-28 17:47       ` Matthias Kaehlcke
2019-01-29 13:08         ` Balakrishna Godavarthi
2019-01-24 12:08 ` [PATCH v9 2/3] Bluetooth: hci_qca: Deassert RTS while baudrate change command Balakrishna Godavarthi
2019-01-25  0:12   ` Matthias Kaehlcke
2019-01-28 13:45     ` Balakrishna Godavarthi [this message]
2019-01-24 12:08 ` [PATCH v9 3/3] Bluetooth: hci_qca: Disable IBS state machine and flush Tx buffer Balakrishna Godavarthi
2019-01-25  0:55   ` Matthias Kaehlcke
2019-02-01 11:40     ` Balakrishna Godavarthi
2019-02-01 18:35       ` Matthias Kaehlcke

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=6b18e30fb1b747d674a75cb265b5821b@codeaurora.org \
    --to=bgodavar@codeaurora.org \
    --cc=hemantg@codeaurora.org \
    --cc=johan.hedberg@gmail.com \
    --cc=johan@kernel.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-bluetooth@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=marcel@holtmann.org \
    --cc=mka@chromium.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-Bluetooth Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-bluetooth/0 linux-bluetooth/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-bluetooth linux-bluetooth/ https://lore.kernel.org/linux-bluetooth \
		linux-bluetooth@vger.kernel.org linux-bluetooth@archiver.kernel.org
	public-inbox-index linux-bluetooth


Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-bluetooth


AGPL code for this site: git clone https://public-inbox.org/ public-inbox