linux-can.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH v1 1/3] dt-bindings: can-controller: add support for termination-gpios
@ 2021-08-16 11:48 Oleksij Rempel
  2021-08-16 11:48 ` [PATCH v1 2/3] dt-bindings: can: fsl,flexcan: enable termination-* bindings Oleksij Rempel
  2021-08-16 11:48 ` [PATCH v1 3/3] can: dev: provide optional GPIO based termination support Oleksij Rempel
  0 siblings, 2 replies; 4+ messages in thread
From: Oleksij Rempel @ 2021-08-16 11:48 UTC (permalink / raw)
  To: Wolfgang Grandegger, Marc Kleine-Budde, David S. Miller,
	Jakub Kicinski, Rob Herring
  Cc: Oleksij Rempel, linux-can, netdev, devicetree, linux-kernel,
	kernel, David Jander

Some boards provide GPIO controllable termination resistor. Provide
binding to make use of it.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 .../devicetree/bindings/net/can/can-controller.yaml      | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/can/can-controller.yaml b/Documentation/devicetree/bindings/net/can/can-controller.yaml
index 9cf2ae097156..298ce69a8208 100644
--- a/Documentation/devicetree/bindings/net/can/can-controller.yaml
+++ b/Documentation/devicetree/bindings/net/can/can-controller.yaml
@@ -13,6 +13,15 @@ properties:
   $nodename:
     pattern: "^can(@.*)?$"
 
+  termination-gpios:
+    description: GPIO pin to enable CAN bus termination.
+
+  termination-ohms:
+    description: The resistance value of the CAN bus termination resistor.
+    $ref: /schemas/types.yaml#/definitions/uint16-array
+    minimum: 1
+    maximum: 65535
+
 additionalProperties: true
 
 ...
-- 
2.30.2


^ permalink raw reply related	[flat|nested] 4+ messages in thread

* [PATCH v1 2/3] dt-bindings: can: fsl,flexcan: enable termination-* bindings
  2021-08-16 11:48 [PATCH v1 1/3] dt-bindings: can-controller: add support for termination-gpios Oleksij Rempel
@ 2021-08-16 11:48 ` Oleksij Rempel
  2021-08-16 11:48 ` [PATCH v1 3/3] can: dev: provide optional GPIO based termination support Oleksij Rempel
  1 sibling, 0 replies; 4+ messages in thread
From: Oleksij Rempel @ 2021-08-16 11:48 UTC (permalink / raw)
  To: Wolfgang Grandegger, Marc Kleine-Budde, David S. Miller,
	Jakub Kicinski, Rob Herring
  Cc: Oleksij Rempel, linux-can, netdev, devicetree, linux-kernel,
	kernel, David Jander

Enable termination-* binding and provide validation example for it.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 .../bindings/net/can/fsl,flexcan.yaml          | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml b/Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml
index 55bff1586b6f..ef31696eb642 100644
--- a/Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml
+++ b/Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml
@@ -119,6 +119,9 @@ properties:
     minimum: 0
     maximum: 2
 
+  termination-gpios: true
+  termination-ohms: true
+
 required:
   - compatible
   - reg
@@ -148,3 +151,18 @@ examples:
         fsl,stop-mode = <&gpr 0x34 28>;
         fsl,scu-index = /bits/ 8 <1>;
     };
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/gpio/gpio.h>
+
+    can@2090000 {
+        compatible = "fsl,imx6q-flexcan";
+        reg = <0x02090000 0x4000>;
+        interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH>;
+        clocks = <&clks 1>, <&clks 2>;
+        clock-names = "ipg", "per";
+        fsl,stop-mode = <&gpr 0x34 28>;
+        fsl,scu-index = /bits/ 8 <1>;
+        termination-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+        termination-ohms = /bits/ 16 <150>;
+    };
-- 
2.30.2


^ permalink raw reply related	[flat|nested] 4+ messages in thread

* [PATCH v1 3/3] can: dev: provide optional GPIO based termination support
  2021-08-16 11:48 [PATCH v1 1/3] dt-bindings: can-controller: add support for termination-gpios Oleksij Rempel
  2021-08-16 11:48 ` [PATCH v1 2/3] dt-bindings: can: fsl,flexcan: enable termination-* bindings Oleksij Rempel
@ 2021-08-16 11:48 ` Oleksij Rempel
  2021-08-17  0:19   ` Vincent MAILHOL
  1 sibling, 1 reply; 4+ messages in thread
From: Oleksij Rempel @ 2021-08-16 11:48 UTC (permalink / raw)
  To: Wolfgang Grandegger, Marc Kleine-Budde, David S. Miller,
	Jakub Kicinski, Rob Herring
  Cc: Oleksij Rempel, linux-can, netdev, devicetree, linux-kernel,
	kernel, David Jander

For CAN buses to work, a termination resistor has to be present at both
ends of the bus. This resistor is usually 120 Ohms, other values may be
required for special bus topologies.

This patch adds support for a generic GPIO based CAN termination. The
resistor value has to be specified via device tree, and it can only be
attached to or detached from the bus. By default the termination is not
active.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 drivers/net/can/dev/dev.c | 54 +++++++++++++++++++++++++++++++++++++++
 include/linux/can/dev.h   |  7 +++++
 2 files changed, 61 insertions(+)

diff --git a/drivers/net/can/dev/dev.c b/drivers/net/can/dev/dev.c
index 311d8564d611..b4a6c7a6fc18 100644
--- a/drivers/net/can/dev/dev.c
+++ b/drivers/net/can/dev/dev.c
@@ -15,6 +15,7 @@
 #include <linux/can/dev.h>
 #include <linux/can/skb.h>
 #include <linux/can/led.h>
+#include <linux/gpio/consumer.h>
 #include <linux/of.h>
 
 #define MOD_DESC "CAN device driver interface"
@@ -400,10 +401,57 @@ void close_candev(struct net_device *dev)
 }
 EXPORT_SYMBOL_GPL(close_candev);
 
+static int can_set_termination(struct net_device *ndev, u16 term)
+{
+	struct can_priv *priv = netdev_priv(ndev);
+	int set;
+
+	if (term == priv->termination_gpio_ohms[CAN_TERMINATION_GPIO_ENABLED])
+		set = 1;
+	else
+		set = 0;
+
+	gpiod_set_value(priv->termination_gpio, set);
+
+	return 0;
+}
+
+static int can_get_termination(struct net_device *ndev)
+{
+	struct can_priv *priv = netdev_priv(ndev);
+	struct device *dev = ndev->dev.parent;
+	struct gpio_desc *gpio;
+	u16 term;
+	int ret;
+
+	/* Disabling termination by default is the safe choice: Else if many
+	 * bus participants enable it, no communication is possible at all.
+	 */
+	gpio = devm_gpiod_get_optional(dev, "termination", GPIOD_OUT_LOW);
+	if (IS_ERR(gpio))
+		return dev_err_probe(dev, PTR_ERR(gpio),
+				     "Cannot get termination-gpios\n");
+
+	ret = device_property_read_u16(dev, "termination-ohms", &term);
+	if (ret)
+		return ret;
+
+	priv->termination_const_cnt = ARRAY_SIZE(priv->termination_gpio_ohms);
+	priv->termination_const = priv->termination_gpio_ohms;
+	priv->termination_gpio = gpio;
+	priv->termination_gpio_ohms[CAN_TERMINATION_GPIO_DISABLED] =
+		CAN_TERMINATION_DISABLED;
+	priv->termination_gpio_ohms[CAN_TERMINATION_GPIO_ENABLED] = term;
+	priv->do_set_termination = can_set_termination;
+
+	return 0;
+}
+
 /* Register the CAN network device */
 int register_candev(struct net_device *dev)
 {
 	struct can_priv *priv = netdev_priv(dev);
+	int err;
 
 	/* Ensure termination_const, termination_const_cnt and
 	 * do_set_termination consistency. All must be either set or
@@ -419,6 +467,12 @@ int register_candev(struct net_device *dev)
 	if (!priv->data_bitrate_const != !priv->data_bitrate_const_cnt)
 		return -EINVAL;
 
+	if (!priv->termination_const) {
+		err = can_get_termination(dev);
+		if (err)
+			return err;
+	}
+
 	dev->rtnl_link_ops = &can_link_ops;
 	netif_carrier_off(dev);
 
diff --git a/include/linux/can/dev.h b/include/linux/can/dev.h
index 27b275e463da..82bdc5b09a3a 100644
--- a/include/linux/can/dev.h
+++ b/include/linux/can/dev.h
@@ -32,6 +32,11 @@ enum can_mode {
 	CAN_MODE_SLEEP
 };
 
+enum can_termination_gpio {
+	CAN_TERMINATION_GPIO_DISABLED = 0,
+	CAN_TERMINATION_GPIO_ENABLED,
+};
+
 /*
  * CAN common private data
  */
@@ -55,6 +60,8 @@ struct can_priv {
 	unsigned int termination_const_cnt;
 	const u16 *termination_const;
 	u16 termination;
+	struct gpio_desc *termination_gpio;
+	u16 termination_gpio_ohms[2];
 
 	enum can_state state;
 
-- 
2.30.2


^ permalink raw reply related	[flat|nested] 4+ messages in thread

* Re: [PATCH v1 3/3] can: dev: provide optional GPIO based termination support
  2021-08-16 11:48 ` [PATCH v1 3/3] can: dev: provide optional GPIO based termination support Oleksij Rempel
@ 2021-08-17  0:19   ` Vincent MAILHOL
  0 siblings, 0 replies; 4+ messages in thread
From: Vincent MAILHOL @ 2021-08-17  0:19 UTC (permalink / raw)
  To: Oleksij Rempel
  Cc: Wolfgang Grandegger, Marc Kleine-Budde, David S. Miller,
	Jakub Kicinski, Rob Herring, linux-can, netdev, devicetree,
	open list, kernel, David Jander

On Mon. 16 Aug 2021 at 20:48, Oleksij Rempel <o.rempel@pengutronix.de> wrote:
> For CAN buses to work, a termination resistor has to be present at both
> ends of the bus. This resistor is usually 120 Ohms, other values may be
> required for special bus topologies.
>
> This patch adds support for a generic GPIO based CAN termination. The
> resistor value has to be specified via device tree, and it can only be
> attached to or detached from the bus. By default the termination is not
> active.
>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  drivers/net/can/dev/dev.c | 54 +++++++++++++++++++++++++++++++++++++++
>  include/linux/can/dev.h   |  7 +++++
>  2 files changed, 61 insertions(+)
>
> diff --git a/drivers/net/can/dev/dev.c b/drivers/net/can/dev/dev.c
> index 311d8564d611..b4a6c7a6fc18 100644
> --- a/drivers/net/can/dev/dev.c
> +++ b/drivers/net/can/dev/dev.c
> @@ -15,6 +15,7 @@
>  #include <linux/can/dev.h>
>  #include <linux/can/skb.h>
>  #include <linux/can/led.h>
> +#include <linux/gpio/consumer.h>
>  #include <linux/of.h>
>
>  #define MOD_DESC "CAN device driver interface"
> @@ -400,10 +401,57 @@ void close_candev(struct net_device *dev)
>  }
>  EXPORT_SYMBOL_GPL(close_candev);
>
> +static int can_set_termination(struct net_device *ndev, u16 term)
> +{
> +       struct can_priv *priv = netdev_priv(ndev);
> +       int set;
> +
> +       if (term == priv->termination_gpio_ohms[CAN_TERMINATION_GPIO_ENABLED])
> +               set = 1;
> +       else
> +               set = 0;
> +
> +       gpiod_set_value(priv->termination_gpio, set);
> +
> +       return 0;
> +}
> +
> +static int can_get_termination(struct net_device *ndev)
> +{
> +       struct can_priv *priv = netdev_priv(ndev);
> +       struct device *dev = ndev->dev.parent;
> +       struct gpio_desc *gpio;
> +       u16 term;
> +       int ret;
> +
> +       /* Disabling termination by default is the safe choice: Else if many
> +        * bus participants enable it, no communication is possible at all.
> +        */
> +       gpio = devm_gpiod_get_optional(dev, "termination", GPIOD_OUT_LOW);
> +       if (IS_ERR(gpio))
> +               return dev_err_probe(dev, PTR_ERR(gpio),
> +                                    "Cannot get termination-gpios\n");
> +
> +       ret = device_property_read_u16(dev, "termination-ohms", &term);
> +       if (ret)
> +               return ret;
> +
> +       priv->termination_const_cnt = ARRAY_SIZE(priv->termination_gpio_ohms);
> +       priv->termination_const = priv->termination_gpio_ohms;
> +       priv->termination_gpio = gpio;
> +       priv->termination_gpio_ohms[CAN_TERMINATION_GPIO_DISABLED] =
> +               CAN_TERMINATION_DISABLED;
> +       priv->termination_gpio_ohms[CAN_TERMINATION_GPIO_ENABLED] = term;
> +       priv->do_set_termination = can_set_termination;
> +
> +       return 0;
> +}
> +
>  /* Register the CAN network device */
>  int register_candev(struct net_device *dev)
>  {
>         struct can_priv *priv = netdev_priv(dev);
> +       int err;
>
>         /* Ensure termination_const, termination_const_cnt and
>          * do_set_termination consistency. All must be either set or
> @@ -419,6 +467,12 @@ int register_candev(struct net_device *dev)
>         if (!priv->data_bitrate_const != !priv->data_bitrate_const_cnt)
>                 return -EINVAL;
>
> +       if (!priv->termination_const) {
> +               err = can_get_termination(dev);
> +               if (err)
> +                       return err;
> +       }
> +
>         dev->rtnl_link_ops = &can_link_ops;
>         netif_carrier_off(dev);
>
> diff --git a/include/linux/can/dev.h b/include/linux/can/dev.h
> index 27b275e463da..82bdc5b09a3a 100644
> --- a/include/linux/can/dev.h
> +++ b/include/linux/can/dev.h
> @@ -32,6 +32,11 @@ enum can_mode {
>         CAN_MODE_SLEEP
>  };
>
> +enum can_termination_gpio {
> +       CAN_TERMINATION_GPIO_DISABLED = 0,
> +       CAN_TERMINATION_GPIO_ENABLED,

I would add a last entry to automatically calculate the length of
the termination_gpio_ohms array.

+       CAN_TERMINATION_GPIO_MAX

> +};
> +
>  /*
>   * CAN common private data
>   */
> @@ -55,6 +60,8 @@ struct can_priv {
>         unsigned int termination_const_cnt;
>         const u16 *termination_const;
>         u16 termination;
> +       struct gpio_desc *termination_gpio;
> +       u16 termination_gpio_ohms[2];

This way, you can replace the constant value 2:

+       u16 termination_gpio_ohms[CAN_TERMINATION_GPIO_MAX];

>
>         enum can_state state;

Yours sincerely,
Vincent

^ permalink raw reply	[flat|nested] 4+ messages in thread

end of thread, other threads:[~2021-08-17  0:20 UTC | newest]

Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-08-16 11:48 [PATCH v1 1/3] dt-bindings: can-controller: add support for termination-gpios Oleksij Rempel
2021-08-16 11:48 ` [PATCH v1 2/3] dt-bindings: can: fsl,flexcan: enable termination-* bindings Oleksij Rempel
2021-08-16 11:48 ` [PATCH v1 3/3] can: dev: provide optional GPIO based termination support Oleksij Rempel
2021-08-17  0:19   ` Vincent MAILHOL

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).