linux-can.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Marc Kleine-Budde <mkl@pengutronix.de>
To: netdev@vger.kernel.org
Cc: davem@davemloft.net, kuba@kernel.org, linux-can@vger.kernel.org,
	kernel@pengutronix.de, Oleksij Rempel <o.rempel@pengutronix.de>,
	Marc Kleine-Budde <mkl@pengutronix.de>
Subject: [PATCH net-next 04/22] can: dev: provide optional GPIO based termination support
Date: Thu, 19 Aug 2021 15:38:55 +0200	[thread overview]
Message-ID: <20210819133913.657715-5-mkl@pengutronix.de> (raw)
In-Reply-To: <20210819133913.657715-1-mkl@pengutronix.de>

From: Oleksij Rempel <o.rempel@pengutronix.de>

For CAN buses to work, a termination resistor has to be present at both
ends of the bus. This resistor is usually 120 Ohms, other values may be
required for special bus topologies.

This patch adds support for a generic GPIO based CAN termination. The
resistor value has to be specified via device tree, and it can only be
attached to or detached from the bus. By default the termination is not
active.

Link: https://lore.kernel.org/r/20210818071232.20585-4-o.rempel@pengutronix.de
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
---
 drivers/net/can/dev/dev.c | 66 +++++++++++++++++++++++++++++++++++++++
 include/linux/can/dev.h   |  8 +++++
 2 files changed, 74 insertions(+)

diff --git a/drivers/net/can/dev/dev.c b/drivers/net/can/dev/dev.c
index 311d8564d611..e3d840b81357 100644
--- a/drivers/net/can/dev/dev.c
+++ b/drivers/net/can/dev/dev.c
@@ -15,6 +15,7 @@
 #include <linux/can/dev.h>
 #include <linux/can/skb.h>
 #include <linux/can/led.h>
+#include <linux/gpio/consumer.h>
 #include <linux/of.h>
 
 #define MOD_DESC "CAN device driver interface"
@@ -400,10 +401,69 @@ void close_candev(struct net_device *dev)
 }
 EXPORT_SYMBOL_GPL(close_candev);
 
+static int can_set_termination(struct net_device *ndev, u16 term)
+{
+	struct can_priv *priv = netdev_priv(ndev);
+	int set;
+
+	if (term == priv->termination_gpio_ohms[CAN_TERMINATION_GPIO_ENABLED])
+		set = 1;
+	else
+		set = 0;
+
+	gpiod_set_value(priv->termination_gpio, set);
+
+	return 0;
+}
+
+static int can_get_termination(struct net_device *ndev)
+{
+	struct can_priv *priv = netdev_priv(ndev);
+	struct device *dev = ndev->dev.parent;
+	struct gpio_desc *gpio;
+	u32 term;
+	int ret;
+
+	/* Disabling termination by default is the safe choice: Else if many
+	 * bus participants enable it, no communication is possible at all.
+	 */
+	gpio = devm_gpiod_get_optional(dev, "termination", GPIOD_OUT_LOW);
+	if (IS_ERR(gpio))
+		return dev_err_probe(dev, PTR_ERR(gpio),
+				     "Cannot get termination-gpios\n");
+
+	if (!gpio)
+		return 0;
+
+	ret = device_property_read_u32(dev, "termination-ohms", &term);
+	if (ret) {
+		netdev_err(ndev, "Cannot get termination-ohms: %pe\n",
+			   ERR_PTR(ret));
+		return ret;
+	}
+
+	if (term > U16_MAX) {
+		netdev_err(ndev, "Invalid termination-ohms value (%u > %u)\n",
+			   term, U16_MAX);
+		return -EINVAL;
+	}
+
+	priv->termination_const_cnt = ARRAY_SIZE(priv->termination_gpio_ohms);
+	priv->termination_const = priv->termination_gpio_ohms;
+	priv->termination_gpio = gpio;
+	priv->termination_gpio_ohms[CAN_TERMINATION_GPIO_DISABLED] =
+		CAN_TERMINATION_DISABLED;
+	priv->termination_gpio_ohms[CAN_TERMINATION_GPIO_ENABLED] = term;
+	priv->do_set_termination = can_set_termination;
+
+	return 0;
+}
+
 /* Register the CAN network device */
 int register_candev(struct net_device *dev)
 {
 	struct can_priv *priv = netdev_priv(dev);
+	int err;
 
 	/* Ensure termination_const, termination_const_cnt and
 	 * do_set_termination consistency. All must be either set or
@@ -419,6 +479,12 @@ int register_candev(struct net_device *dev)
 	if (!priv->data_bitrate_const != !priv->data_bitrate_const_cnt)
 		return -EINVAL;
 
+	if (!priv->termination_const) {
+		err = can_get_termination(dev);
+		if (err)
+			return err;
+	}
+
 	dev->rtnl_link_ops = &can_link_ops;
 	netif_carrier_off(dev);
 
diff --git a/include/linux/can/dev.h b/include/linux/can/dev.h
index 27b275e463da..2413253e54c7 100644
--- a/include/linux/can/dev.h
+++ b/include/linux/can/dev.h
@@ -32,6 +32,12 @@ enum can_mode {
 	CAN_MODE_SLEEP
 };
 
+enum can_termination_gpio {
+	CAN_TERMINATION_GPIO_DISABLED = 0,
+	CAN_TERMINATION_GPIO_ENABLED,
+	CAN_TERMINATION_GPIO_MAX,
+};
+
 /*
  * CAN common private data
  */
@@ -55,6 +61,8 @@ struct can_priv {
 	unsigned int termination_const_cnt;
 	const u16 *termination_const;
 	u16 termination;
+	struct gpio_desc *termination_gpio;
+	u16 termination_gpio_ohms[CAN_TERMINATION_GPIO_MAX];
 
 	enum can_state state;
 
-- 
2.32.0



  parent reply	other threads:[~2021-08-19 13:39 UTC|newest]

Thread overview: 24+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-08-19 13:38 pull-request: can-next 2021-08-19 Marc Kleine-Budde
2021-08-19 13:38 ` [PATCH net-next 01/22] mailmap: update email address of Matthias Fuchs and Thomas Körper Marc Kleine-Budde
2021-08-19 13:38 ` [PATCH net-next 02/22] dt-bindings: can-controller: add support for termination-gpios Marc Kleine-Budde
2021-08-19 13:38 ` [PATCH net-next 03/22] dt-bindings: can: fsl,flexcan: enable termination-* bindings Marc Kleine-Budde
2021-08-19 13:38 ` Marc Kleine-Budde [this message]
2021-08-19 13:38 ` [PATCH net-next 05/22] can: netlink: allow user to turn off unsupported features Marc Kleine-Budde
2021-08-19 13:38 ` [PATCH net-next 06/22] MAINTAINERS: add Vincent MAILHOL as maintainer for the ETAS ES58X CAN/USB driver Marc Kleine-Budde
2021-08-19 13:38 ` [PATCH net-next 07/22] can: etas_es58x: clean-up documentation of struct es58x_fd_tx_conf_msg Marc Kleine-Budde
2021-08-19 13:38 ` [PATCH net-next 08/22] can: mcp251xfd: mark some instances of struct mcp251xfd_priv as const Marc Kleine-Budde
2021-08-19 13:39 ` [PATCH net-next 09/22] dt-bindings: net: can: renesas,rcar-canfd: Document RZ/G2L SoC Marc Kleine-Budde
2021-08-19 13:39 ` [PATCH net-next 10/22] can: rcar_canfd: Add support for RZ/G2L family Marc Kleine-Budde
2021-08-19 13:39 ` [PATCH net-next 11/22] can: tcan4x5x: cdev_to_priv(): remove stray empty line Marc Kleine-Budde
2021-08-19 13:39 ` [PATCH net-next 12/22] can: m_can: fix block comment style Marc Kleine-Budde
2021-08-19 13:39 ` [PATCH net-next 13/22] can: m_can: Disable IRQs on FIFO bus errors Marc Kleine-Budde
2021-08-19 13:39 ` [PATCH net-next 14/22] can: m_can: Batch FIFO reads during CAN receive Marc Kleine-Budde
2021-08-19 13:39 ` [PATCH net-next 15/22] can: m_can: Batch FIFO writes during CAN transmit Marc Kleine-Budde
2021-08-19 13:39 ` [PATCH net-next 16/22] dt-bindings: net: can: c_can: convert to json-schema Marc Kleine-Budde
2021-08-19 13:39 ` [PATCH net-next 17/22] can: c_can: c_can_do_tx(): fix typo in comment Marc Kleine-Budde
2021-08-19 13:39 ` [PATCH net-next 18/22] can: c_can: rename IF_RX -> IF_NAPI Marc Kleine-Budde
2021-08-19 13:39 ` [PATCH net-next 19/22] can: c_can: remove struct c_can_priv::priv field Marc Kleine-Budde
2021-08-19 13:39 ` [PATCH net-next 20/22] can: c_can: exit c_can_do_tx() early if no frames have been sent Marc Kleine-Budde
2021-08-19 13:39 ` [PATCH net-next 21/22] can: c_can: support tx ring algorithm Marc Kleine-Budde
2021-08-19 13:39 ` [PATCH net-next 22/22] can: c_can: cache frames to operate as a true FIFO Marc Kleine-Budde
2021-08-19 19:00 ` pull-request: can-next 2021-08-19 patchwork-bot+netdevbpf

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210819133913.657715-5-mkl@pengutronix.de \
    --to=mkl@pengutronix.de \
    --cc=davem@davemloft.net \
    --cc=kernel@pengutronix.de \
    --cc=kuba@kernel.org \
    --cc=linux-can@vger.kernel.org \
    --cc=netdev@vger.kernel.org \
    --cc=o.rempel@pengutronix.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).