Linux-Clk Archive on lore.kernel.org
 help / Atom feed
* [PATCH 0/2] clk: aspeed: Setup video engine clocking
@ 2018-12-11 20:12 Eddie James
  2018-12-11 20:12 ` [PATCH 1/2] clk: aspeed: Add video engine reset index definition Eddie James
  2018-12-11 20:12 ` [PATCH 2/2] clk: aspeed: Setup video engine clocking Eddie James
  0 siblings, 2 replies; 6+ messages in thread
From: Eddie James @ 2018-12-11 20:12 UTC (permalink / raw)
  To: linux-kernel
  Cc: linux-aspeed, andrew, sboyd, mturquette, linux-clk,
	linux-arm-kernel, joel, Eddie James

This series adds the parent clock definitions and muxing for the AST2xxx
video engine.

I sent this series before as part of my first patch set for the video engine,
but probably better to send it separately.

Eddie James (2):
  clk: aspeed: Add video engine reset index definition
  clk: aspeed: Setup video engine clocking

 drivers/clk/clk-aspeed.c                 | 41 ++++++++++++++++++++++++++++++--
 include/dt-bindings/clock/aspeed-clock.h |  1 +
 2 files changed, 40 insertions(+), 2 deletions(-)

-- 
1.8.3.1


^ permalink raw reply	[flat|nested] 6+ messages in thread

* [PATCH 1/2] clk: aspeed: Add video engine reset index definition
  2018-12-11 20:12 [PATCH 0/2] clk: aspeed: Setup video engine clocking Eddie James
@ 2018-12-11 20:12 ` Eddie James
  2018-12-11 20:12 ` [PATCH 2/2] clk: aspeed: Setup video engine clocking Eddie James
  1 sibling, 0 replies; 6+ messages in thread
From: Eddie James @ 2018-12-11 20:12 UTC (permalink / raw)
  To: linux-kernel
  Cc: linux-aspeed, andrew, sboyd, mturquette, linux-clk,
	linux-arm-kernel, joel, Eddie James

Add an index into the array of resets kept in the Aspeed clock driver
for the video engine. This isn't a HW bit definition.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 include/dt-bindings/clock/aspeed-clock.h | 1 +
 1 file changed, 1 insertion(+)

diff --git a/include/dt-bindings/clock/aspeed-clock.h b/include/dt-bindings/clock/aspeed-clock.h
index f437386..15a9059 100644
--- a/include/dt-bindings/clock/aspeed-clock.h
+++ b/include/dt-bindings/clock/aspeed-clock.h
@@ -50,5 +50,6 @@
 #define ASPEED_RESET_I2C		7
 #define ASPEED_RESET_AHB		8
 #define ASPEED_RESET_CRT1		9
+#define ASPEED_RESET_VIDEO		10
 
 #endif
-- 
1.8.3.1


^ permalink raw reply	[flat|nested] 6+ messages in thread

* [PATCH 2/2] clk: aspeed: Setup video engine clocking
  2018-12-11 20:12 [PATCH 0/2] clk: aspeed: Setup video engine clocking Eddie James
  2018-12-11 20:12 ` [PATCH 1/2] clk: aspeed: Add video engine reset index definition Eddie James
@ 2018-12-11 20:12 ` Eddie James
  2018-12-14  1:02   ` Joel Stanley
  1 sibling, 1 reply; 6+ messages in thread
From: Eddie James @ 2018-12-11 20:12 UTC (permalink / raw)
  To: linux-kernel
  Cc: linux-aspeed, andrew, sboyd, mturquette, linux-clk,
	linux-arm-kernel, joel, Eddie James

Add the video engine reset bit. Add eclk mux and clock divider table.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
---
 drivers/clk/clk-aspeed.c | 41 +++++++++++++++++++++++++++++++++++++++--
 1 file changed, 39 insertions(+), 2 deletions(-)

diff --git a/drivers/clk/clk-aspeed.c b/drivers/clk/clk-aspeed.c
index 5961367..f16ce7d 100644
--- a/drivers/clk/clk-aspeed.c
+++ b/drivers/clk/clk-aspeed.c
@@ -87,7 +87,7 @@ struct aspeed_clk_gate {
 /* TODO: ask Aspeed about the actual parent data */
 static const struct aspeed_gate_data aspeed_gates[] = {
 	/*				 clk rst   name			parent	flags */
-	[ASPEED_CLK_GATE_ECLK] =	{  0, -1, "eclk-gate",		"eclk",	0 }, /* Video Engine */
+	[ASPEED_CLK_GATE_ECLK] =	{  0,  6, "eclk-gate",		"eclk",	0 }, /* Video Engine */
 	[ASPEED_CLK_GATE_GCLK] =	{  1,  7, "gclk-gate",		NULL,	0 }, /* 2D engine */
 	[ASPEED_CLK_GATE_MCLK] =	{  2, -1, "mclk-gate",		"mpll",	CLK_IS_CRITICAL }, /* SDRAM */
 	[ASPEED_CLK_GATE_VCLK] =	{  3,  6, "vclk-gate",		NULL,	0 }, /* Video Capture */
@@ -113,6 +113,24 @@ struct aspeed_clk_gate {
 	[ASPEED_CLK_GATE_LHCCLK] =	{ 28, -1, "lhclk-gate",		"lhclk", 0 }, /* LPC master/LPC+ */
 };
 
+static const char * const eclk_parent_names[] = {
+	"mpll",
+	"hpll",
+	"dpll",
+};
+
+static const struct clk_div_table ast2500_eclk_div_table[] = {
+	{ 0x0, 2 },
+	{ 0x1, 2 },
+	{ 0x2, 3 },
+	{ 0x3, 4 },
+	{ 0x4, 5 },
+	{ 0x5, 6 },
+	{ 0x6, 7 },
+	{ 0x7, 8 },
+	{ 0 }
+};
+
 static const struct clk_div_table ast2500_mac_div_table[] = {
 	{ 0x0, 4 }, /* Yep, really. Aspeed confirmed this is correct */
 	{ 0x1, 4 },
@@ -192,18 +210,21 @@ static struct clk_hw *aspeed_ast2500_calc_pll(const char *name, u32 val)
 
 struct aspeed_clk_soc_data {
 	const struct clk_div_table *div_table;
+	const struct clk_div_table *eclk_div_table;
 	const struct clk_div_table *mac_div_table;
 	struct clk_hw *(*calc_pll)(const char *name, u32 val);
 };
 
 static const struct aspeed_clk_soc_data ast2500_data = {
 	.div_table = ast2500_div_table,
+	.eclk_div_table = ast2500_eclk_div_table,
 	.mac_div_table = ast2500_mac_div_table,
 	.calc_pll = aspeed_ast2500_calc_pll,
 };
 
 static const struct aspeed_clk_soc_data ast2400_data = {
 	.div_table = ast2400_div_table,
+	.eclk_div_table = ast2400_div_table,
 	.mac_div_table = ast2400_div_table,
 	.calc_pll = aspeed_ast2400_calc_pll,
 };
@@ -317,6 +338,7 @@ struct aspeed_reset {
 	[ASPEED_RESET_PECI]	= 10,
 	[ASPEED_RESET_I2C]	=  2,
 	[ASPEED_RESET_AHB]	=  1,
+	[ASPEED_RESET_VIDEO]	=  6,
 
 	/*
 	 * SCUD4 resets start at an offset to separate them from
@@ -522,6 +544,22 @@ static int aspeed_clk_probe(struct platform_device *pdev)
 		return PTR_ERR(hw);
 	aspeed_clk_data->hws[ASPEED_CLK_24M] = hw;
 
+	hw = clk_hw_register_mux(dev, "eclk-mux", eclk_parent_names,
+				 ARRAY_SIZE(eclk_parent_names), 0,
+				 scu_base + ASPEED_CLK_SELECTION, 2, 0x3, 0,
+				 &aspeed_clk_lock);
+	if (IS_ERR(hw))
+		return PTR_ERR(hw);
+	aspeed_clk_data->hws[ASPEED_CLK_ECLK_MUX] = hw;
+
+	hw = clk_hw_register_divider_table(dev, "eclk", "eclk-mux", 0,
+					   scu_base + ASPEED_CLK_SELECTION, 28,
+					   3, 0, soc_data->eclk_div_table,
+					   &aspeed_clk_lock);
+	if (IS_ERR(hw))
+		return PTR_ERR(hw);
+	aspeed_clk_data->hws[ASPEED_CLK_ECLK] = hw;
+
 	/*
 	 * TODO: There are a number of clocks that not included in this driver
 	 * as more information is required:
@@ -531,7 +569,6 @@ static int aspeed_clk_probe(struct platform_device *pdev)
 	 *   RGMII
 	 *   RMII
 	 *   UART[1..5] clock source mux
-	 *   Video Engine (ECLK) mux and clock divider
 	 */
 
 	for (i = 0; i < ARRAY_SIZE(aspeed_gates); i++) {
-- 
1.8.3.1


^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH 2/2] clk: aspeed: Setup video engine clocking
  2018-12-11 20:12 ` [PATCH 2/2] clk: aspeed: Setup video engine clocking Eddie James
@ 2018-12-14  1:02   ` Joel Stanley
  2018-12-14 15:47     ` Eddie James
  0 siblings, 1 reply; 6+ messages in thread
From: Joel Stanley @ 2018-12-14  1:02 UTC (permalink / raw)
  To: eajames
  Cc: Linux Kernel Mailing List, linux-aspeed, Andrew Jeffery,
	Stephen Boyd, Michael Turquette, linux-clk, Linux ARM

Hi Eddie,

On Wed, 12 Dec 2018 at 06:42, Eddie James <eajames@linux.ibm.com> wrote:
>
> Add the video engine reset bit. Add eclk mux and clock divider table.
>
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> Acked-by: Stephen Boyd <sboyd@kernel.org>
> ---
>  drivers/clk/clk-aspeed.c | 41 +++++++++++++++++++++++++++++++++++++++--
>  1 file changed, 39 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/clk/clk-aspeed.c b/drivers/clk/clk-aspeed.c
> index 5961367..f16ce7d 100644
> --- a/drivers/clk/clk-aspeed.c
> +++ b/drivers/clk/clk-aspeed.c
> @@ -87,7 +87,7 @@ struct aspeed_clk_gate {
>  /* TODO: ask Aspeed about the actual parent data */
>  static const struct aspeed_gate_data aspeed_gates[] = {
>         /*                               clk rst   name                 parent  flags */
> -       [ASPEED_CLK_GATE_ECLK] =        {  0, -1, "eclk-gate",          "eclk", 0 }, /* Video Engine */
> +       [ASPEED_CLK_GATE_ECLK] =        {  0,  6, "eclk-gate",          "eclk", 0 }, /* Video Engine */


>         [ASPEED_CLK_GATE_GCLK] =        {  1,  7, "gclk-gate",          NULL,   0 }, /* 2D engine */
>         [ASPEED_CLK_GATE_MCLK] =        {  2, -1, "mclk-gate",          "mpll", CLK_IS_CRITICAL }, /* SDRAM */
>         [ASPEED_CLK_GATE_VCLK] =        {  3,  6, "vclk-gate",          NULL,   0 }, /* Video Capture */
> @@ -113,6 +113,24 @@ struct aspeed_clk_gate {
>         [ASPEED_CLK_GATE_LHCCLK] =      { 28, -1, "lhclk-gate",         "lhclk", 0 }, /* LPC master/LPC+ */
>  };
>
> +static const char * const eclk_parent_names[] = {
> +       "mpll",

Is the mpll really an input to the eclk?

> +       "hpll",
> +       "dpll",

We don't have a dpll in the driver that I can see.

> +};
> +
> +static const struct clk_div_table ast2500_eclk_div_table[] = {

Is the clocking setup different on the ast2400?

> +       { 0x0, 2 },
> +       { 0x1, 2 },
> +       { 0x2, 3 },
> +       { 0x3, 4 },
> +       { 0x4, 5 },
> +       { 0x5, 6 },
> +       { 0x6, 7 },
> +       { 0x7, 8 },
> +       { 0 }
> +};

> @@ -317,6 +338,7 @@ struct aspeed_reset {
>         [ASPEED_RESET_PECI]     = 10,
>         [ASPEED_RESET_I2C]      =  2,
>         [ASPEED_RESET_AHB]      =  1,
> +       [ASPEED_RESET_VIDEO]    =  6,

You've added the reset line to the ASPEED_CLK_GATE_ECLK clock so you
do not need to separately expose the reset controller. Instead
enabling the clock will deassert the rest line for you.

This means you should drop the change from the header too, and it
affects the bindings document for the video engine.

>
>         /*
>          * SCUD4 resets start at an offset to separate them from
> @@ -522,6 +544,22 @@ static int aspeed_clk_probe(struct platform_device *pdev)
>                 return PTR_ERR(hw);
>         aspeed_clk_data->hws[ASPEED_CLK_24M] = hw;
>
> +       hw = clk_hw_register_mux(dev, "eclk-mux", eclk_parent_names,
> +                                ARRAY_SIZE(eclk_parent_names), 0,
> +                                scu_base + ASPEED_CLK_SELECTION, 2, 0x3, 0,
> +                                &aspeed_clk_lock);
> +       if (IS_ERR(hw))
> +               return PTR_ERR(hw);
> +       aspeed_clk_data->hws[ASPEED_CLK_ECLK_MUX] = hw;
> +
> +       hw = clk_hw_register_divider_table(dev, "eclk", "eclk-mux", 0,
> +                                          scu_base + ASPEED_CLK_SELECTION, 28,
> +                                          3, 0, soc_data->eclk_div_table,
> +                                          &aspeed_clk_lock);
> +       if (IS_ERR(hw))
> +               return PTR_ERR(hw);
> +       aspeed_clk_data->hws[ASPEED_CLK_ECLK] = hw;
> +
>         /*
>          * TODO: There are a number of clocks that not included in this driver
>          * as more information is required:
> @@ -531,7 +569,6 @@ static int aspeed_clk_probe(struct platform_device *pdev)
>          *   RGMII
>          *   RMII
>          *   UART[1..5] clock source mux
> -        *   Video Engine (ECLK) mux and clock divider
>          */
>
>         for (i = 0; i < ARRAY_SIZE(aspeed_gates); i++) {
> --
> 1.8.3.1
>

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH 2/2] clk: aspeed: Setup video engine clocking
  2018-12-14  1:02   ` Joel Stanley
@ 2018-12-14 15:47     ` Eddie James
  2019-01-30 19:28       ` Stephen Boyd
  0 siblings, 1 reply; 6+ messages in thread
From: Eddie James @ 2018-12-14 15:47 UTC (permalink / raw)
  To: Joel Stanley
  Cc: Linux Kernel Mailing List, linux-aspeed, Andrew Jeffery,
	Stephen Boyd, Michael Turquette, linux-clk, Linux ARM



On 12/13/2018 07:02 PM, Joel Stanley wrote:
> Hi Eddie,
>
> On Wed, 12 Dec 2018 at 06:42, Eddie James <eajames@linux.ibm.com> wrote:
>> Add the video engine reset bit. Add eclk mux and clock divider table.
>>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> Acked-by: Stephen Boyd <sboyd@kernel.org>
>> ---
>>   drivers/clk/clk-aspeed.c | 41 +++++++++++++++++++++++++++++++++++++++--
>>   1 file changed, 39 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/clk/clk-aspeed.c b/drivers/clk/clk-aspeed.c
>> index 5961367..f16ce7d 100644
>> --- a/drivers/clk/clk-aspeed.c
>> +++ b/drivers/clk/clk-aspeed.c
>> @@ -87,7 +87,7 @@ struct aspeed_clk_gate {
>>   /* TODO: ask Aspeed about the actual parent data */
>>   static const struct aspeed_gate_data aspeed_gates[] = {
>>          /*                               clk rst   name                 parent  flags */
>> -       [ASPEED_CLK_GATE_ECLK] =        {  0, -1, "eclk-gate",          "eclk", 0 }, /* Video Engine */
>> +       [ASPEED_CLK_GATE_ECLK] =        {  0,  6, "eclk-gate",          "eclk", 0 }, /* Video Engine */
>
>>          [ASPEED_CLK_GATE_GCLK] =        {  1,  7, "gclk-gate",          NULL,   0 }, /* 2D engine */
>>          [ASPEED_CLK_GATE_MCLK] =        {  2, -1, "mclk-gate",          "mpll", CLK_IS_CRITICAL }, /* SDRAM */
>>          [ASPEED_CLK_GATE_VCLK] =        {  3,  6, "vclk-gate",          NULL,   0 }, /* Video Capture */
>> @@ -113,6 +113,24 @@ struct aspeed_clk_gate {
>>          [ASPEED_CLK_GATE_LHCCLK] =      { 28, -1, "lhclk-gate",         "lhclk", 0 }, /* LPC master/LPC+ */
>>   };
>>
>> +static const char * const eclk_parent_names[] = {
>> +       "mpll",
> Is the mpll really an input to the eclk?

Yep, it's the default.

>
>> +       "hpll",
>> +       "dpll",
> We don't have a dpll in the driver that I can see.

True... I supposed I would just add the parent here now in case the dpll 
clock is ever added.

>
>> +};
>> +
>> +static const struct clk_div_table ast2500_eclk_div_table[] = {
> Is the clocking setup different on the ast2400?

Yes, the dividers are the default ast2400 ones.

>
>> +       { 0x0, 2 },
>> +       { 0x1, 2 },
>> +       { 0x2, 3 },
>> +       { 0x3, 4 },
>> +       { 0x4, 5 },
>> +       { 0x5, 6 },
>> +       { 0x6, 7 },
>> +       { 0x7, 8 },
>> +       { 0 }
>> +};
>> @@ -317,6 +338,7 @@ struct aspeed_reset {
>>          [ASPEED_RESET_PECI]     = 10,
>>          [ASPEED_RESET_I2C]      =  2,
>>          [ASPEED_RESET_AHB]      =  1,
>> +       [ASPEED_RESET_VIDEO]    =  6,
> You've added the reset line to the ASPEED_CLK_GATE_ECLK clock so you
> do not need to separately expose the reset controller. Instead
> enabling the clock will deassert the rest line for you.
>
> This means you should drop the change from the header too, and it
> affects the bindings document for the video engine.

I want that reset available separately for use in the video engine 
actually. I could do without it, but it's somewhat useful.

Thanks,
Eddie

>
>>          /*
>>           * SCUD4 resets start at an offset to separate them from
>> @@ -522,6 +544,22 @@ static int aspeed_clk_probe(struct platform_device *pdev)
>>                  return PTR_ERR(hw);
>>          aspeed_clk_data->hws[ASPEED_CLK_24M] = hw;
>>
>> +       hw = clk_hw_register_mux(dev, "eclk-mux", eclk_parent_names,
>> +                                ARRAY_SIZE(eclk_parent_names), 0,
>> +                                scu_base + ASPEED_CLK_SELECTION, 2, 0x3, 0,
>> +                                &aspeed_clk_lock);
>> +       if (IS_ERR(hw))
>> +               return PTR_ERR(hw);
>> +       aspeed_clk_data->hws[ASPEED_CLK_ECLK_MUX] = hw;
>> +
>> +       hw = clk_hw_register_divider_table(dev, "eclk", "eclk-mux", 0,
>> +                                          scu_base + ASPEED_CLK_SELECTION, 28,
>> +                                          3, 0, soc_data->eclk_div_table,
>> +                                          &aspeed_clk_lock);
>> +       if (IS_ERR(hw))
>> +               return PTR_ERR(hw);
>> +       aspeed_clk_data->hws[ASPEED_CLK_ECLK] = hw;
>> +
>>          /*
>>           * TODO: There are a number of clocks that not included in this driver
>>           * as more information is required:
>> @@ -531,7 +569,6 @@ static int aspeed_clk_probe(struct platform_device *pdev)
>>           *   RGMII
>>           *   RMII
>>           *   UART[1..5] clock source mux
>> -        *   Video Engine (ECLK) mux and clock divider
>>           */
>>
>>          for (i = 0; i < ARRAY_SIZE(aspeed_gates); i++) {
>> --
>> 1.8.3.1
>>


^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH 2/2] clk: aspeed: Setup video engine clocking
  2018-12-14 15:47     ` Eddie James
@ 2019-01-30 19:28       ` Stephen Boyd
  0 siblings, 0 replies; 6+ messages in thread
From: Stephen Boyd @ 2019-01-30 19:28 UTC (permalink / raw)
  To: Eddie James, Joel Stanley
  Cc: Linux Kernel Mailing List, linux-aspeed, Andrew Jeffery,
	Michael Turquette, linux-clk, Linux ARM

Quoting Eddie James (2018-12-14 07:47:53)
> 
> 
> On 12/13/2018 07:02 PM, Joel Stanley wrote:
> 
> >
> >> +       { 0x0, 2 },
> >> +       { 0x1, 2 },
> >> +       { 0x2, 3 },
> >> +       { 0x3, 4 },
> >> +       { 0x4, 5 },
> >> +       { 0x5, 6 },
> >> +       { 0x6, 7 },
> >> +       { 0x7, 8 },
> >> +       { 0 }
> >> +};
> >> @@ -317,6 +338,7 @@ struct aspeed_reset {
> >>          [ASPEED_RESET_PECI]     = 10,
> >>          [ASPEED_RESET_I2C]      =  2,
> >>          [ASPEED_RESET_AHB]      =  1,
> >> +       [ASPEED_RESET_VIDEO]    =  6,
> > You've added the reset line to the ASPEED_CLK_GATE_ECLK clock so you
> > do not need to separately expose the reset controller. Instead
> > enabling the clock will deassert the rest line for you.
> >
> > This means you should drop the change from the header too, and it
> > affects the bindings document for the video engine.
> 
> I want that reset available separately for use in the video engine 
> actually. I could do without it, but it's somewhat useful.
> 

Joel, are you happy with these patches? I'm tempted to drop these
changes from my queue because there hasn't been any news in over a
month.


^ permalink raw reply	[flat|nested] 6+ messages in thread

end of thread, back to index

Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-12-11 20:12 [PATCH 0/2] clk: aspeed: Setup video engine clocking Eddie James
2018-12-11 20:12 ` [PATCH 1/2] clk: aspeed: Add video engine reset index definition Eddie James
2018-12-11 20:12 ` [PATCH 2/2] clk: aspeed: Setup video engine clocking Eddie James
2018-12-14  1:02   ` Joel Stanley
2018-12-14 15:47     ` Eddie James
2019-01-30 19:28       ` Stephen Boyd

Linux-Clk Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-clk/0 linux-clk/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-clk linux-clk/ https://lore.kernel.org/linux-clk \
		linux-clk@vger.kernel.org linux-clk@archiver.kernel.org
	public-inbox-index linux-clk


Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-clk


AGPL code for this site: git clone https://public-inbox.org/ public-inbox