Linux-Clk Archive on lore.kernel.org
 help / color / Atom feed
From: Sricharan R <sricharan@codeaurora.org>
To: sricharan@codeaurora.org, agross@kernel.org,
	devicetree@vger.kernel.org, linus.walleij@linaro.org,
	linux-arm-kernel@lists.infradead.org,
	linux-arm-msm@vger.kernel.org, linux-clk@vger.kernel.org,
	linux-gpio@vger.kernel.org, linux-kernel@vger.kernel.org,
	linux-soc@vger.kernel.org, robh+dt@kernel.org, sboyd@kernel.org,
	sivaprak@codeaurora.org
Subject: [PATCH V3 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings
Date: Fri,  3 Jan 2020 17:19:33 +0530
Message-ID: <1578052177-6778-2-git-send-email-sricharan@codeaurora.org> (raw)
In-Reply-To: <1578052177-6778-1-git-send-email-sricharan@codeaurora.org>

Add device tree binding Documentation details for ipq6018
pinctrl driver.

Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
---
 [v3] Fixed the example dt node, inherited properties

 .../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml     | 166 +++++++++++++++++++++
 1 file changed, 166 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
new file mode 100644
index 0000000..e959c5f
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
@@ -0,0 +1,166 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,ipq6018-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies, Inc. IPQ6018 TLMM block
+
+maintainers:
+  - Sricharan R <sricharan@codeaurora.org>
+
+description: |
+  This binding describes the Top Level Mode Multiplexer block found in the
+  IPQ6018 platform.
+
+properties:
+  compatible:
+    const: qcom,ipq6018-pinctrl
+  reg:
+    maxItems: 1
+  interrupts:
+    Description: Specifies the TLMM summary IRQ
+    maxItems: 1
+  interrupt-controller: true
+  '#interrupt-cells':
+    Description:
+      Specifies the PIN numbers and Flags, as defined in defined in
+      include/dt-bindings/interrupt-controller/irq.h
+    const: 2
+  gpio-controller: true
+  '#gpio-cells':
+    Description: Specifying the pin number and flags, as defined in
+      include/dt-bindings/gpio/gpio.h
+    const: 2
+  gpio-ranges:
+    Description: Documentation/devicetree/bindings/gpio/gpio.txt
+    maxItems: 1
+
+#PIN CONFIGURATION NODES
+patternProperties:
+  '-pins$':
+    type: object
+    Description:
+      Pinctrl node's client devices use subnodes for desired pin configuration.
+      Client device subnodes use below standard properties.
+
+    Properties:
+      pins:
+        allOf:
+          $ref: /schemas/types.yaml#/definitions/string
+          enum:
+            gpio0-gpio80
+            sdc1_clk
+            sdc1_cmd
+            sdc1_data
+            sdc2_clk
+            sdc2_cmd
+            sdc2_data
+            qdsd_cmd
+            qdsd_data0
+            qdsd_data1
+            qdsd_data2
+            qdsd_data3
+        Description:
+          List of gpio pins affected by the properties specified in this
+          subnode.
+
+      function:
+        allOf:
+          $ref: /schemas/types.yaml#/definitions/string
+          enum:
+            adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char,
+            atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac,
+            atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0,
+            atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp_i2c1,
+            blsp_i2c2, blsp_i2c3, blsp_i2c4, blsp_i2c5, blsp_i2c6,  blsp_spi1,
+            blsp_spi1_cs1, blsp_spi1_cs2, blsp_spi1_cs3, blsp_spi2,
+            blsp_spi2_cs1, blsp_spi2_cs2, blsp_spi2_cs3, blsp_spi3,
+            blsp_spi3_cs1, blsp_spi3_cs2, blsp_spi3_cs3, blsp_spi4, blsp_spi5,
+            blsp_spi6, blsp_uart1, blsp_uart2, blsp_uim1, blsp_uim2, cam1_rst,
+            cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0,
+            cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v,
+            dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass,
+            flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a,
+            gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0,
+            gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2,
+            ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc,
+            nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s,
+            pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
+            pwr_modem_enabled_a,  pwr_modem_enabled_b, pwr_nav_enabled_a,
+            pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1,
+            qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0,
+            qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1,
+            qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b,
+            qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write,
+            sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3,
+            uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst
+        Description:
+          Specify the alternative function to be configured for the specified
+          pins.
+      bias-disable:
+        allOf:
+          $ref: /schemas/pinctrl/pincfg-node.yaml
+        Description:
+          The specified pins should be configured as no pull.
+      bias-pull-down:
+        allOf:
+          $ref: /schemas/pinctrl/pincfg-node.yaml
+        Description:
+          The specified pins should be configured as pull down.
+      bias-pull-up:
+        allOf:
+          $ref: /schemas/pinctrl/pincfg-node.yaml
+        Description:
+          The specified pins should be configured as pull up.
+      output-high:
+        allOf:
+          $ref: /schemas/pinctrl/pincfg-node.yaml
+        Description:
+          The specified pins are configured in output mode, driven high.
+          This option is not available for sdc pins.
+      output-low:
+        allOf:
+          $ref: /schemas/pinctrl/pincfg-node.yaml
+        Description:
+          The specified pins are configured in output mode, driven low.
+          This option is not available for sdc pins.
+      drive-strength:
+        allOf:
+          $ref: /schemas/types.yaml#/definitions/uint32
+          enum: [2, 4, 6, 8, 10, 12, 14, 16]
+        Description:
+          Selects the drive strength for the specified pins, in mA.
+
+    required:
+      - pins
+      - function
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupt-controller
+  - '#interrupt-cells'
+  - gpio-controller
+  - '#gpio-cells'
+  - gpio-ranges
+
+example:
+        tlmm: pinctrl@1000000 {
+                compatible = "qcom,ipq6018-pinctrl";
+                reg = <0x01000000 0x300000>;
+                interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+                gpio-controller;
+                #gpio-cells = <2>;
+                gpio-ranges = <&tlmm 0 80>;
+                interrupt-controller;
+                #interrupt-cells = <2>;
+
+                serial_3_pins: serial3-pinmux {
+                        pins = "gpio44", "gpio45";
+                        function = "blsp2_uart";
+                        drive-strength = <8>;
+                        bias-pull-down;
+                };
+       };
-- 
1.9.1

  reply index

Thread overview: 12+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-01-03 11:49 [PATCH V3 0/5] Add minimal boot support for IPQ6018 Sricharan R
2020-01-03 11:49 ` Sricharan R [this message]
2020-01-04  0:58   ` [PATCH V3 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings Rob Herring
2020-01-06  5:25     ` Sricharan R
2020-01-07 11:55   ` Linus Walleij
2020-01-09  9:21     ` Sricharan R
2020-01-03 11:49 ` [PATCH V3 2/5] pinctrl: qcom: Add ipq6018 pinctrl driver Sricharan R
2020-01-04  1:33   ` Bjorn Andersson
2020-01-03 11:49 ` [PATCH V3 3/5] dt-bindings: qcom: Add ipq6018 bindings Sricharan R
2020-01-04  0:59   ` Rob Herring
2020-01-03 11:49 ` [PATCH V3 4/5] arm64: dts: Add ipq6018 SoC and CP01 board support Sricharan R
2020-01-03 11:49 ` [PATCH V3 5/5] arm64: defconfig: Enable qcom ipq6018 clock and pinctrl Sricharan R

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1578052177-6778-2-git-send-email-sricharan@codeaurora.org \
    --to=sricharan@codeaurora.org \
    --cc=agross@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=linus.walleij@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-soc@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    --cc=sboyd@kernel.org \
    --cc=sivaprak@codeaurora.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-Clk Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-clk/0 linux-clk/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-clk linux-clk/ https://lore.kernel.org/linux-clk \
		linux-clk@vger.kernel.org
	public-inbox-index linux-clk

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-clk


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git