* [PATCH v4 1/8] dt-bindings: add documentation of xilinx clocking wizard
2020-06-26 12:41 [PATCH v4 0/8] clk: clockwizard: Driver updates Shubhrajyoti Datta
@ 2020-06-26 12:41 ` Shubhrajyoti Datta
2020-06-26 12:41 ` [PATCH v4 2/8] clk: clock-wizard: Add the clockwizard to clk directory Shubhrajyoti Datta
` (6 subsequent siblings)
7 siblings, 0 replies; 10+ messages in thread
From: Shubhrajyoti Datta @ 2020-06-26 12:41 UTC (permalink / raw)
To: linux-clk
Cc: sboyd, robh+dt, gregkh, shubhrajyoti.datta, devicetree,
linux-kernel, michals, Shubhrajyoti Datta
Add the devicetree binding for the xilinx clocking wizard.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
---
v4:
Move to yaml format
.../bindings/clock/xlnx,clocking-wizard.yaml | 71 ++++++++++++++++++++++
1 file changed, 71 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/xlnx,clocking-wizard.yaml
diff --git a/Documentation/devicetree/bindings/clock/xlnx,clocking-wizard.yaml b/Documentation/devicetree/bindings/clock/xlnx,clocking-wizard.yaml
new file mode 100644
index 0000000..5a8e991
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/xlnx,clocking-wizard.yaml
@@ -0,0 +1,71 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/xlnx,clocking-wiz.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx clocking wizard
+
+maintainers:
+ - Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
+
+description: |
+ The clocking wizard is a soft ip clocking block of Xilinx versal. It
+ reads required input clock frequencies from the devicetree and acts as clock
+ clock output.
+
+select: false
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - xlnx,clocking-wizard
+ - xlnx,clocking-wizard-6.0
+
+ "#clock-cells":
+ const: 1
+
+ clocks:
+ description: List of clock specifiers which are external input
+ clocks to the given clock controller.
+ items:
+ - description: clock input
+ - description: axi clock
+
+ clock-names:
+ items:
+ - const: clk_in1
+ - const: s_axi_aclk
+
+ speed-grade:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - enum: [1, 2, 3]
+ description:
+ Speed grade of the device.
+ maxItems: 1
+
+required:
+ - compatible
+ - "#clock-cells"
+ - clocks
+ - clock-names
+ - speed-grade
+
+additionalProperties: false
+
+examples:
+ - |
+ clock-generator@40040000 {
+ #clock-cells = <1>;
+ reg = <0x40040000 0x1000>;
+ compatible = "xlnx,clk-wizard-1.0";
+ speed-grade = <1>;
+ clock-names = "clk_in1", "s_axi_aclk";
+ clocks = <&clkc 15>, <&clkc 15>;
+ clock-output-names = "clk_out1", "clk_out2",
+ "clk_out3", "clk_out4", "clk_out5",
+ "clk_out6", "clk_out7";
+ };
+...
--
2.1.1
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH v4 2/8] clk: clock-wizard: Add the clockwizard to clk directory
2020-06-26 12:41 [PATCH v4 0/8] clk: clockwizard: Driver updates Shubhrajyoti Datta
2020-06-26 12:41 ` [PATCH v4 1/8] dt-bindings: add documentation of xilinx clocking wizard Shubhrajyoti Datta
@ 2020-06-26 12:41 ` Shubhrajyoti Datta
2020-06-26 12:41 ` [PATCH v4 3/8] clk: clock-wizard: Fix kernel-doc warning Shubhrajyoti Datta
` (5 subsequent siblings)
7 siblings, 0 replies; 10+ messages in thread
From: Shubhrajyoti Datta @ 2020-06-26 12:41 UTC (permalink / raw)
To: linux-clk
Cc: sboyd, robh+dt, gregkh, shubhrajyoti.datta, devicetree,
linux-kernel, michals, Shubhrajyoti Datta
Add clocking wizard driver to clk.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
---
drivers/clk/Kconfig | 9 +
drivers/clk/Makefile | 1 +
drivers/clk/clk-xlnx-clock-wizard.c | 338 ++++++++++++++++++++++++++++++++++++
3 files changed, 348 insertions(+)
create mode 100644 drivers/clk/clk-xlnx-clock-wizard.c
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index 69934c0..5f66076 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -360,6 +360,15 @@ config COMMON_CLK_FIXED_MMIO
help
Support for Memory Mapped IO Fixed clocks
+config COMMON_CLK_XLNX_CLKWZRD
+ tristate "Xilinx Clocking Wizard"
+ depends on COMMON_CLK && OF
+ help
+ Support for the Xilinx Clocking Wizard IP core clock generator.
+ Adds support for clocking wizard and compatible.
+ This driver supports the Xilinx clocking wizard programmable clock
+ synthesizer. The number of output is configurable in the design.
+
source "drivers/clk/actions/Kconfig"
source "drivers/clk/analogbits/Kconfig"
source "drivers/clk/baikal-t1/Kconfig"
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index ca9af11..f41287859 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -68,6 +68,7 @@ obj-$(CONFIG_ARCH_VT8500) += clk-vt8500.o
obj-$(CONFIG_COMMON_CLK_VC5) += clk-versaclock5.o
obj-$(CONFIG_COMMON_CLK_WM831X) += clk-wm831x.o
obj-$(CONFIG_COMMON_CLK_XGENE) += clk-xgene.o
+obj-$(CONFIG_COMMON_CLK_XLNX_CLKWZRD) += clk-xlnx-clock-wizard.o
# please keep this section sorted lexicographically by directory path name
obj-y += actions/
diff --git a/drivers/clk/clk-xlnx-clock-wizard.c b/drivers/clk/clk-xlnx-clock-wizard.c
new file mode 100644
index 0000000..b31524a
--- /dev/null
+++ b/drivers/clk/clk-xlnx-clock-wizard.c
@@ -0,0 +1,338 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx 'Clocking Wizard' driver
+ *
+ * Copyright (C) 2013 - 2020 Xilinx
+ *
+ * Sören Brinkmann <soren.brinkmann@xilinx.com>
+ * Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
+ *
+ */
+
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/slab.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/module.h>
+#include <linux/err.h>
+
+#define WZRD_NUM_OUTPUTS 7
+#define WZRD_ACLK_MAX_FREQ 250000000UL
+
+#define WZRD_CLK_CFG_REG(n) (0x200 + 4 * (n))
+
+#define WZRD_CLKOUT0_FRAC_EN BIT(18)
+#define WZRD_CLKFBOUT_FRAC_EN BIT(26)
+
+#define WZRD_CLKFBOUT_MULT_SHIFT 8
+#define WZRD_CLKFBOUT_MULT_MASK (0xff << WZRD_CLKFBOUT_MULT_SHIFT)
+#define WZRD_DIVCLK_DIVIDE_SHIFT 0
+#define WZRD_DIVCLK_DIVIDE_MASK (0xff << WZRD_DIVCLK_DIVIDE_SHIFT)
+#define WZRD_CLKOUT_DIVIDE_SHIFT 0
+#define WZRD_CLKOUT_DIVIDE_MASK (0xff << WZRD_DIVCLK_DIVIDE_SHIFT)
+
+enum clk_wzrd_int_clks {
+ wzrd_clk_mul,
+ wzrd_clk_mul_div,
+ wzrd_clk_int_max
+};
+
+/**
+ * struct clk_wzrd:
+ * @clk_data: Clock data
+ * @nb: Notifier block
+ * @base: Memory base
+ * @clk_in1: Handle to input clock 'clk_in1'
+ * @axi_clk: Handle to input clock 's_axi_aclk'
+ * @clks_internal: Internal clocks
+ * @clkout: Output clocks
+ * @speed_grade: Speed grade of the device
+ * @suspended: Flag indicating power state of the device
+ */
+struct clk_wzrd {
+ struct clk_onecell_data clk_data;
+ struct notifier_block nb;
+ void __iomem *base;
+ struct clk *clk_in1;
+ struct clk *axi_clk;
+ struct clk *clks_internal[wzrd_clk_int_max];
+ struct clk *clkout[WZRD_NUM_OUTPUTS];
+ unsigned int speed_grade;
+ bool suspended;
+};
+
+#define to_clk_wzrd(_nb) container_of(_nb, struct clk_wzrd, nb)
+
+/* maximum frequencies for input/output clocks per speed grade */
+static const unsigned long clk_wzrd_max_freq[] = {
+ 800000000UL,
+ 933000000UL,
+ 1066000000UL
+};
+
+static int clk_wzrd_clk_notifier(struct notifier_block *nb, unsigned long event,
+ void *data)
+{
+ unsigned long max;
+ struct clk_notifier_data *ndata = data;
+ struct clk_wzrd *clk_wzrd = to_clk_wzrd(nb);
+
+ if (clk_wzrd->suspended)
+ return NOTIFY_OK;
+
+ if (ndata->clk == clk_wzrd->clk_in1)
+ max = clk_wzrd_max_freq[clk_wzrd->speed_grade - 1];
+ else if (ndata->clk == clk_wzrd->axi_clk)
+ max = WZRD_ACLK_MAX_FREQ;
+ else
+ return NOTIFY_DONE; /* should never happen */
+
+ switch (event) {
+ case PRE_RATE_CHANGE:
+ if (ndata->new_rate > max)
+ return NOTIFY_BAD;
+ return NOTIFY_OK;
+ case POST_RATE_CHANGE:
+ case ABORT_RATE_CHANGE:
+ default:
+ return NOTIFY_DONE;
+ }
+}
+
+static int __maybe_unused clk_wzrd_suspend(struct device *dev)
+{
+ struct clk_wzrd *clk_wzrd = dev_get_drvdata(dev);
+
+ clk_disable_unprepare(clk_wzrd->axi_clk);
+ clk_wzrd->suspended = true;
+
+ return 0;
+}
+
+static int __maybe_unused clk_wzrd_resume(struct device *dev)
+{
+ int ret;
+ struct clk_wzrd *clk_wzrd = dev_get_drvdata(dev);
+
+ ret = clk_prepare_enable(clk_wzrd->axi_clk);
+ if (ret) {
+ dev_err(dev, "unable to enable s_axi_aclk\n");
+ return ret;
+ }
+
+ clk_wzrd->suspended = false;
+
+ return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(clk_wzrd_dev_pm_ops, clk_wzrd_suspend,
+ clk_wzrd_resume);
+
+static int clk_wzrd_probe(struct platform_device *pdev)
+{
+ int i, ret;
+ u32 reg;
+ unsigned long rate;
+ const char *clk_name;
+ struct clk_wzrd *clk_wzrd;
+ struct resource *mem;
+ struct device_node *np = pdev->dev.of_node;
+
+ clk_wzrd = devm_kzalloc(&pdev->dev, sizeof(*clk_wzrd), GFP_KERNEL);
+ if (!clk_wzrd)
+ return -ENOMEM;
+ platform_set_drvdata(pdev, clk_wzrd);
+
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ clk_wzrd->base = devm_ioremap_resource(&pdev->dev, mem);
+ if (IS_ERR(clk_wzrd->base))
+ return PTR_ERR(clk_wzrd->base);
+
+ ret = of_property_read_u32(np, "speed-grade", &clk_wzrd->speed_grade);
+ if (!ret) {
+ if (clk_wzrd->speed_grade < 1 || clk_wzrd->speed_grade > 3) {
+ dev_warn(&pdev->dev, "invalid speed grade '%d'\n",
+ clk_wzrd->speed_grade);
+ clk_wzrd->speed_grade = 0;
+ }
+ }
+
+ clk_wzrd->clk_in1 = devm_clk_get(&pdev->dev, "clk_in1");
+ if (IS_ERR(clk_wzrd->clk_in1)) {
+ if (clk_wzrd->clk_in1 != ERR_PTR(-EPROBE_DEFER))
+ dev_err(&pdev->dev, "clk_in1 not found\n");
+ return PTR_ERR(clk_wzrd->clk_in1);
+ }
+
+ clk_wzrd->axi_clk = devm_clk_get(&pdev->dev, "s_axi_aclk");
+ if (IS_ERR(clk_wzrd->axi_clk)) {
+ if (clk_wzrd->axi_clk != ERR_PTR(-EPROBE_DEFER))
+ dev_err(&pdev->dev, "s_axi_aclk not found\n");
+ return PTR_ERR(clk_wzrd->axi_clk);
+ }
+ ret = clk_prepare_enable(clk_wzrd->axi_clk);
+ if (ret) {
+ dev_err(&pdev->dev, "enabling s_axi_aclk failed\n");
+ return ret;
+ }
+ rate = clk_get_rate(clk_wzrd->axi_clk);
+ if (rate > WZRD_ACLK_MAX_FREQ) {
+ dev_err(&pdev->dev, "s_axi_aclk frequency (%lu) too high\n",
+ rate);
+ ret = -EINVAL;
+ goto err_disable_clk;
+ }
+
+ /* we don't support fractional div/mul yet */
+ reg = readl(clk_wzrd->base + WZRD_CLK_CFG_REG(0)) &
+ WZRD_CLKFBOUT_FRAC_EN;
+ reg |= readl(clk_wzrd->base + WZRD_CLK_CFG_REG(2)) &
+ WZRD_CLKOUT0_FRAC_EN;
+ if (reg)
+ dev_warn(&pdev->dev, "fractional div/mul not supported\n");
+
+ /* register multiplier */
+ reg = (readl(clk_wzrd->base + WZRD_CLK_CFG_REG(0)) &
+ WZRD_CLKFBOUT_MULT_MASK) >> WZRD_CLKFBOUT_MULT_SHIFT;
+ clk_name = kasprintf(GFP_KERNEL, "%s_mul", dev_name(&pdev->dev));
+ if (!clk_name) {
+ ret = -ENOMEM;
+ goto err_disable_clk;
+ }
+ clk_wzrd->clks_internal[wzrd_clk_mul] = clk_register_fixed_factor
+ (&pdev->dev, clk_name,
+ __clk_get_name(clk_wzrd->clk_in1),
+ 0, reg, 1);
+ kfree(clk_name);
+ if (IS_ERR(clk_wzrd->clks_internal[wzrd_clk_mul])) {
+ dev_err(&pdev->dev, "unable to register fixed-factor clock\n");
+ ret = PTR_ERR(clk_wzrd->clks_internal[wzrd_clk_mul]);
+ goto err_disable_clk;
+ }
+
+ /* register div */
+ reg = (readl(clk_wzrd->base + WZRD_CLK_CFG_REG(0)) &
+ WZRD_DIVCLK_DIVIDE_MASK) >> WZRD_DIVCLK_DIVIDE_SHIFT;
+ clk_name = kasprintf(GFP_KERNEL, "%s_mul_div", dev_name(&pdev->dev));
+ if (!clk_name) {
+ ret = -ENOMEM;
+ goto err_rm_int_clk;
+ }
+
+ clk_wzrd->clks_internal[wzrd_clk_mul_div] = clk_register_fixed_factor
+ (&pdev->dev, clk_name,
+ __clk_get_name(clk_wzrd->clks_internal[wzrd_clk_mul]),
+ 0, 1, reg);
+ if (IS_ERR(clk_wzrd->clks_internal[wzrd_clk_mul_div])) {
+ dev_err(&pdev->dev, "unable to register divider clock\n");
+ ret = PTR_ERR(clk_wzrd->clks_internal[wzrd_clk_mul_div]);
+ goto err_rm_int_clk;
+ }
+
+ /* register div per output */
+ for (i = WZRD_NUM_OUTPUTS - 1; i >= 0 ; i--) {
+ const char *clkout_name;
+
+ if (of_property_read_string_index(np, "clock-output-names", i,
+ &clkout_name)) {
+ dev_err(&pdev->dev,
+ "clock output name not specified\n");
+ ret = -EINVAL;
+ goto err_rm_int_clks;
+ }
+ reg = readl(clk_wzrd->base + WZRD_CLK_CFG_REG(2) + i * 12);
+ reg &= WZRD_CLKOUT_DIVIDE_MASK;
+ reg >>= WZRD_CLKOUT_DIVIDE_SHIFT;
+ clk_wzrd->clkout[i] = clk_register_fixed_factor
+ (&pdev->dev, clkout_name, clk_name, 0, 1, reg);
+ if (IS_ERR(clk_wzrd->clkout[i])) {
+ int j;
+
+ for (j = i + 1; j < WZRD_NUM_OUTPUTS; j++)
+ clk_unregister(clk_wzrd->clkout[j]);
+ dev_err(&pdev->dev,
+ "unable to register divider clock\n");
+ ret = PTR_ERR(clk_wzrd->clkout[i]);
+ goto err_rm_int_clks;
+ }
+ }
+
+ kfree(clk_name);
+
+ clk_wzrd->clk_data.clks = clk_wzrd->clkout;
+ clk_wzrd->clk_data.clk_num = ARRAY_SIZE(clk_wzrd->clkout);
+ of_clk_add_provider(np, of_clk_src_onecell_get, &clk_wzrd->clk_data);
+
+ if (clk_wzrd->speed_grade) {
+ clk_wzrd->nb.notifier_call = clk_wzrd_clk_notifier;
+
+ ret = clk_notifier_register(clk_wzrd->clk_in1,
+ &clk_wzrd->nb);
+ if (ret)
+ dev_warn(&pdev->dev,
+ "unable to register clock notifier\n");
+
+ ret = clk_notifier_register(clk_wzrd->axi_clk, &clk_wzrd->nb);
+ if (ret)
+ dev_warn(&pdev->dev,
+ "unable to register clock notifier\n");
+ }
+
+ return 0;
+
+err_rm_int_clks:
+ clk_unregister(clk_wzrd->clks_internal[1]);
+err_rm_int_clk:
+ kfree(clk_name);
+ clk_unregister(clk_wzrd->clks_internal[0]);
+err_disable_clk:
+ clk_disable_unprepare(clk_wzrd->axi_clk);
+
+ return ret;
+}
+
+static int clk_wzrd_remove(struct platform_device *pdev)
+{
+ int i;
+ struct clk_wzrd *clk_wzrd = platform_get_drvdata(pdev);
+
+ of_clk_del_provider(pdev->dev.of_node);
+
+ for (i = 0; i < WZRD_NUM_OUTPUTS; i++)
+ clk_unregister(clk_wzrd->clkout[i]);
+ for (i = 0; i < wzrd_clk_int_max; i++)
+ clk_unregister(clk_wzrd->clks_internal[i]);
+
+ if (clk_wzrd->speed_grade) {
+ clk_notifier_unregister(clk_wzrd->axi_clk, &clk_wzrd->nb);
+ clk_notifier_unregister(clk_wzrd->clk_in1, &clk_wzrd->nb);
+ }
+
+ clk_disable_unprepare(clk_wzrd->axi_clk);
+
+ return 0;
+}
+
+static const struct of_device_id clk_wzrd_ids[] = {
+ { .compatible = "xlnx,clocking-wizard" },
+ { .compatible = "xlnx,clocking-wizard-6.0" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, clk_wzrd_ids);
+
+static struct platform_driver clk_wzrd_driver = {
+ .driver = {
+ .name = "clk-wizard",
+ .of_match_table = clk_wzrd_ids,
+ .pm = &clk_wzrd_dev_pm_ops,
+ },
+ .probe = clk_wzrd_probe,
+ .remove = clk_wzrd_remove,
+};
+module_platform_driver(clk_wzrd_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Soeren Brinkmann <soren.brinkmann@xilinx.com");
+MODULE_DESCRIPTION("Driver for the Xilinx Clocking Wizard IP core");
--
2.1.1
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH v4 3/8] clk: clock-wizard: Fix kernel-doc warning
2020-06-26 12:41 [PATCH v4 0/8] clk: clockwizard: Driver updates Shubhrajyoti Datta
2020-06-26 12:41 ` [PATCH v4 1/8] dt-bindings: add documentation of xilinx clocking wizard Shubhrajyoti Datta
2020-06-26 12:41 ` [PATCH v4 2/8] clk: clock-wizard: Add the clockwizard to clk directory Shubhrajyoti Datta
@ 2020-06-26 12:41 ` Shubhrajyoti Datta
2020-06-26 12:41 ` [PATCH v4 4/8] clk: clock-wizard: Add support for dynamic reconfiguration Shubhrajyoti Datta
` (4 subsequent siblings)
7 siblings, 0 replies; 10+ messages in thread
From: Shubhrajyoti Datta @ 2020-06-26 12:41 UTC (permalink / raw)
To: linux-clk
Cc: sboyd, robh+dt, gregkh, shubhrajyoti.datta, devicetree,
linux-kernel, michals, Shubhrajyoti Datta
Update description for the clocking wizard structure
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
---
drivers/clk/clk-xlnx-clock-wizard.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/clk/clk-xlnx-clock-wizard.c b/drivers/clk/clk-xlnx-clock-wizard.c
index b31524a..d6577c8 100644
--- a/drivers/clk/clk-xlnx-clock-wizard.c
+++ b/drivers/clk/clk-xlnx-clock-wizard.c
@@ -40,7 +40,8 @@ enum clk_wzrd_int_clks {
};
/**
- * struct clk_wzrd:
+ * struct clk_wzrd - Clock wizard private data structure
+ *
* @clk_data: Clock data
* @nb: Notifier block
* @base: Memory base
--
2.1.1
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH v4 4/8] clk: clock-wizard: Add support for dynamic reconfiguration
2020-06-26 12:41 [PATCH v4 0/8] clk: clockwizard: Driver updates Shubhrajyoti Datta
` (2 preceding siblings ...)
2020-06-26 12:41 ` [PATCH v4 3/8] clk: clock-wizard: Fix kernel-doc warning Shubhrajyoti Datta
@ 2020-06-26 12:41 ` Shubhrajyoti Datta
2020-06-26 12:41 ` [PATCH v4 5/8] clk: clock-wizard: Add support for fractional support Shubhrajyoti Datta
` (3 subsequent siblings)
7 siblings, 0 replies; 10+ messages in thread
From: Shubhrajyoti Datta @ 2020-06-26 12:41 UTC (permalink / raw)
To: linux-clk
Cc: sboyd, robh+dt, gregkh, shubhrajyoti.datta, devicetree,
linux-kernel, michals, Shubhrajyoti Datta, Chirag Parekh
The patch adds support for dynamic reconfiguration of clock output rate.
Output clocks are registered as dividers and set rate callback function
is used for dynamic reconfiguration.
Based on the initial work from Chirag.
Signed-off-by: Chirag Parekh <chirag.parekh@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
---
drivers/clk/clk-xlnx-clock-wizard.c | 212 +++++++++++++++++++++++++++++++++++-
1 file changed, 206 insertions(+), 6 deletions(-)
diff --git a/drivers/clk/clk-xlnx-clock-wizard.c b/drivers/clk/clk-xlnx-clock-wizard.c
index d6577c8..4b563f3 100644
--- a/drivers/clk/clk-xlnx-clock-wizard.c
+++ b/drivers/clk/clk-xlnx-clock-wizard.c
@@ -31,8 +31,23 @@
#define WZRD_DIVCLK_DIVIDE_SHIFT 0
#define WZRD_DIVCLK_DIVIDE_MASK (0xff << WZRD_DIVCLK_DIVIDE_SHIFT)
#define WZRD_CLKOUT_DIVIDE_SHIFT 0
+#define WZRD_CLKOUT_DIVIDE_WIDTH 8
#define WZRD_CLKOUT_DIVIDE_MASK (0xff << WZRD_DIVCLK_DIVIDE_SHIFT)
+#define WZRD_DR_MAX_INT_DIV_VALUE 255
+#define WZRD_DR_NUM_RETRIES 10000
+#define WZRD_DR_STATUS_REG_OFFSET 0x04
+#define WZRD_DR_LOCK_BIT_MASK 0x00000001
+#define WZRD_DR_INIT_REG_OFFSET 0x25C
+#define WZRD_DR_DIV_TO_PHASE_OFFSET 4
+#define WZRD_DR_BEGIN_DYNA_RECONF 0x03
+
+/* Get the mask from width */
+#define div_mask(width) ((1 << (width)) - 1)
+
+/* Extract divider instance from clock hardware instance */
+#define to_clk_wzrd_divider(_hw) container_of(_hw, struct clk_wzrd_divider, hw)
+
enum clk_wzrd_int_clks {
wzrd_clk_mul,
wzrd_clk_mul_div,
@@ -64,6 +79,29 @@ struct clk_wzrd {
bool suspended;
};
+/**
+ * struct clk_wzrd_divider - clock divider specific to clk_wzrd
+ *
+ * @hw: handle between common and hardware-specific interfaces
+ * @base: base address of register containing the divider
+ * @offset: offset address of register containing the divider
+ * @shift: shift to the divider bit field
+ * @width: width of the divider bit field
+ * @flags: clk_wzrd divider flags
+ * @table: array of value/divider pairs, last entry should have div = 0
+ * @lock: register lock
+ */
+struct clk_wzrd_divider {
+ struct clk_hw hw;
+ void __iomem *base;
+ u16 offset;
+ u8 shift;
+ u8 width;
+ u8 flags;
+ const struct clk_div_table *table;
+ spinlock_t *lock; /* divider lock */
+};
+
#define to_clk_wzrd(_nb) container_of(_nb, struct clk_wzrd, nb)
/* maximum frequencies for input/output clocks per speed grade */
@@ -73,6 +111,164 @@ static const unsigned long clk_wzrd_max_freq[] = {
1066000000UL
};
+/* spin lock variable for clk_wzrd */
+static DEFINE_SPINLOCK(clkwzrd_lock);
+
+static unsigned long clk_wzrd_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct clk_wzrd_divider *divider = to_clk_wzrd_divider(hw);
+ void __iomem *div_addr =
+ (void __iomem *)((u64)divider->base + divider->offset);
+ unsigned int val;
+
+ val = readl(div_addr) >> divider->shift;
+ val &= div_mask(divider->width);
+
+ return divider_recalc_rate(hw, parent_rate, val, divider->table,
+ divider->flags);
+}
+
+static int clk_wzrd_dynamic_reconfig(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ int err = 0;
+ u16 retries;
+ u32 value;
+ unsigned long flags = 0;
+ struct clk_wzrd_divider *divider = to_clk_wzrd_divider(hw);
+ void __iomem *div_addr =
+ (void __iomem *)((u64)divider->base + divider->offset);
+
+ if (divider->lock)
+ spin_lock_irqsave(divider->lock, flags);
+ else
+ __acquire(divider->lock);
+
+ value = DIV_ROUND_CLOSEST(parent_rate, rate);
+
+ /* Cap the value to max */
+ if (value > WZRD_DR_MAX_INT_DIV_VALUE)
+ value = WZRD_DR_MAX_INT_DIV_VALUE;
+
+ /* Set divisor and clear phase offset */
+ writel(value, div_addr);
+ writel(0x00, div_addr + WZRD_DR_DIV_TO_PHASE_OFFSET);
+
+ /* Check status register */
+ retries = WZRD_DR_NUM_RETRIES;
+ while (retries--) {
+ if (readl(divider->base + WZRD_DR_STATUS_REG_OFFSET) &
+ WZRD_DR_LOCK_BIT_MASK)
+ break;
+ }
+
+ if (retries == 0) {
+ err = -ETIMEDOUT;
+ goto err_reconfig;
+ }
+
+ /* Initiate reconfiguration */
+ writel(WZRD_DR_BEGIN_DYNA_RECONF,
+ divider->base + WZRD_DR_INIT_REG_OFFSET);
+
+ /* Check status register */
+ retries = WZRD_DR_NUM_RETRIES;
+ while (retries--) {
+ if (readl(divider->base + WZRD_DR_STATUS_REG_OFFSET) &
+ WZRD_DR_LOCK_BIT_MASK)
+ break;
+ }
+
+ if (retries == 0)
+ err = -ETIMEDOUT;
+
+err_reconfig:
+ if (divider->lock)
+ spin_unlock_irqrestore(divider->lock, flags);
+ else
+ __release(divider->lock);
+
+ return err;
+}
+
+static long clk_wzrd_round_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long *prate)
+{
+ u8 div;
+
+ /*
+ * since we donot change parent rate we just round rate to closest
+ * achievable
+ */
+ div = DIV_ROUND_CLOSEST(*prate, rate);
+
+ return (*prate / div);
+}
+
+static const struct clk_ops clk_wzrd_clk_divider_ops = {
+ .round_rate = clk_wzrd_round_rate,
+ .set_rate = clk_wzrd_dynamic_reconfig,
+ .recalc_rate = clk_wzrd_recalc_rate,
+};
+
+static struct clk *clk_wzrd_register_divider(struct device *dev,
+ const char *name,
+ const char *parent_name,
+ unsigned long flags,
+ void __iomem *base, u16 offset,
+ u8 shift, u8 width,
+ u8 clk_divider_flags,
+ const struct clk_div_table *table,
+ spinlock_t *lock)
+{
+ struct clk_wzrd_divider *div;
+ struct clk_hw *hw;
+ struct clk_init_data init;
+ int ret;
+
+ if (clk_divider_flags & CLK_DIVIDER_HIWORD_MASK) {
+ if (width + shift > 16) {
+ pr_warn("divider value exceeds LOWORD field\n");
+ return ERR_PTR(-EINVAL);
+ }
+ }
+
+ /* allocate the divider */
+ div = kzalloc(sizeof(*div), GFP_KERNEL);
+ if (!div)
+ return ERR_PTR(-ENOMEM);
+
+ init.name = name;
+ if (clk_divider_flags & CLK_DIVIDER_READ_ONLY)
+ init.ops = &clk_divider_ro_ops;
+ else
+ init.ops = &clk_wzrd_clk_divider_ops;
+ init.flags = flags | CLK_IS_BASIC;
+ init.parent_names = (parent_name ? &parent_name : NULL);
+ init.num_parents = (parent_name ? 1 : 0);
+
+ /* struct clk_divider assignments */
+ div->base = base;
+ div->offset = offset;
+ div->shift = shift;
+ div->width = width;
+ div->flags = clk_divider_flags;
+ div->lock = lock;
+ div->hw.init = &init;
+ div->table = table;
+
+ /* register the clock */
+ hw = &div->hw;
+ ret = clk_hw_register(dev, hw);
+ if (ret) {
+ kfree(div);
+ hw = ERR_PTR(ret);
+ }
+
+ return hw->clk;
+}
+
static int clk_wzrd_clk_notifier(struct notifier_block *nb, unsigned long event,
void *data)
{
@@ -225,7 +421,8 @@ static int clk_wzrd_probe(struct platform_device *pdev)
clk_wzrd->clks_internal[wzrd_clk_mul_div] = clk_register_fixed_factor
(&pdev->dev, clk_name,
__clk_get_name(clk_wzrd->clks_internal[wzrd_clk_mul]),
- 0, 1, reg);
+ flags, ctrl_reg, 0, 8, CLK_DIVIDER_ONE_BASED |
+ CLK_DIVIDER_ALLOW_ZERO, &clkwzrd_lock);
if (IS_ERR(clk_wzrd->clks_internal[wzrd_clk_mul_div])) {
dev_err(&pdev->dev, "unable to register divider clock\n");
ret = PTR_ERR(clk_wzrd->clks_internal[wzrd_clk_mul_div]);
@@ -243,11 +440,14 @@ static int clk_wzrd_probe(struct platform_device *pdev)
ret = -EINVAL;
goto err_rm_int_clks;
}
- reg = readl(clk_wzrd->base + WZRD_CLK_CFG_REG(2) + i * 12);
- reg &= WZRD_CLKOUT_DIVIDE_MASK;
- reg >>= WZRD_CLKOUT_DIVIDE_SHIFT;
- clk_wzrd->clkout[i] = clk_register_fixed_factor
- (&pdev->dev, clkout_name, clk_name, 0, 1, reg);
+ clk_wzrd->clkout[i] = clk_wzrd_register_divider(&pdev->dev,
+ clkout_name,
+ clk_name, 0,
+ clk_wzrd->base, (WZRD_CLK_CFG_REG(2) + i * 12),
+ WZRD_CLKOUT_DIVIDE_SHIFT,
+ WZRD_CLKOUT_DIVIDE_WIDTH,
+ CLK_DIVIDER_ONE_BASED | CLK_DIVIDER_ALLOW_ZERO,
+ NULL, &clkwzrd_lock);
if (IS_ERR(clk_wzrd->clkout[i])) {
int j;
--
2.1.1
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH v4 5/8] clk: clock-wizard: Add support for fractional support
2020-06-26 12:41 [PATCH v4 0/8] clk: clockwizard: Driver updates Shubhrajyoti Datta
` (3 preceding siblings ...)
2020-06-26 12:41 ` [PATCH v4 4/8] clk: clock-wizard: Add support for dynamic reconfiguration Shubhrajyoti Datta
@ 2020-06-26 12:41 ` Shubhrajyoti Datta
2020-06-26 12:41 ` [PATCH v4 6/8] clk: clock-wizard: Remove the hardcoding of the clock outputs Shubhrajyoti Datta
` (2 subsequent siblings)
7 siblings, 0 replies; 10+ messages in thread
From: Shubhrajyoti Datta @ 2020-06-26 12:41 UTC (permalink / raw)
To: linux-clk
Cc: sboyd, robh+dt, gregkh, shubhrajyoti.datta, devicetree,
linux-kernel, michals, Shubhrajyoti Datta
Currently the set rate granularity is to integral divisors.
Add support for the fractional divisors.
Only the first output0 is fractional in the hardware.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
---
drivers/clk/clk-xlnx-clock-wizard.c | 192 +++++++++++++++++++++++++++++++++---
1 file changed, 179 insertions(+), 13 deletions(-)
diff --git a/drivers/clk/clk-xlnx-clock-wizard.c b/drivers/clk/clk-xlnx-clock-wizard.c
index 4b563f3..8a7f9bb 100644
--- a/drivers/clk/clk-xlnx-clock-wizard.c
+++ b/drivers/clk/clk-xlnx-clock-wizard.c
@@ -28,11 +28,15 @@
#define WZRD_CLKFBOUT_MULT_SHIFT 8
#define WZRD_CLKFBOUT_MULT_MASK (0xff << WZRD_CLKFBOUT_MULT_SHIFT)
+#define WZRD_CLKFBOUT_FRAC_SHIFT 16
+#define WZRD_CLKFBOUT_FRAC_MASK (0x3ff << WZRD_CLKFBOUT_FRAC_SHIFT)
#define WZRD_DIVCLK_DIVIDE_SHIFT 0
#define WZRD_DIVCLK_DIVIDE_MASK (0xff << WZRD_DIVCLK_DIVIDE_SHIFT)
#define WZRD_CLKOUT_DIVIDE_SHIFT 0
#define WZRD_CLKOUT_DIVIDE_WIDTH 8
#define WZRD_CLKOUT_DIVIDE_MASK (0xff << WZRD_DIVCLK_DIVIDE_SHIFT)
+#define WZRD_CLKOUT_FRAC_SHIFT 8
+#define WZRD_CLKOUT_FRAC_MASK 0x3ff
#define WZRD_DR_MAX_INT_DIV_VALUE 255
#define WZRD_DR_NUM_RETRIES 10000
@@ -51,6 +55,7 @@
enum clk_wzrd_int_clks {
wzrd_clk_mul,
wzrd_clk_mul_div,
+ wzrd_clk_mul_frac,
wzrd_clk_int_max
};
@@ -212,6 +217,161 @@ static const struct clk_ops clk_wzrd_clk_divider_ops = {
.recalc_rate = clk_wzrd_recalc_rate,
};
+static unsigned long clk_wzrd_recalc_ratef(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ unsigned int val;
+ u32 div, frac;
+ struct clk_wzrd_divider *divider = to_clk_wzrd_divider(hw);
+ void __iomem *div_addr =
+ (void __iomem *)((u64)divider->base + divider->offset);
+
+ val = readl(div_addr);
+ div = val & div_mask(divider->width);
+ frac = (val >> WZRD_CLKOUT_FRAC_SHIFT) & WZRD_CLKOUT_FRAC_MASK;
+
+ return ((parent_rate * 1000) / ((div * 1000) + frac));
+}
+
+static int clk_wzrd_dynamic_reconfig_f(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ int err = 0;
+ u16 retries;
+ u32 value, pre;
+ unsigned long flags = 0;
+ unsigned long rate_div, f, clockout0_div;
+ struct clk_wzrd_divider *divider = to_clk_wzrd_divider(hw);
+ void __iomem *div_addr =
+ (void __iomem *)((u64)divider->base + divider->offset);
+
+ if (divider->lock)
+ spin_lock_irqsave(divider->lock, flags);
+ else
+ __acquire(divider->lock);
+
+ rate_div = ((parent_rate * 1000) / rate);
+ clockout0_div = rate_div / 1000;
+
+ pre = DIV_ROUND_CLOSEST((parent_rate * 1000), rate);
+ f = (u32)(pre - (clockout0_div * 1000));
+ f = f & WZRD_CLKOUT_FRAC_MASK;
+
+ value = ((f << WZRD_CLKOUT_DIVIDE_WIDTH) | (clockout0_div &
+ WZRD_CLKOUT_DIVIDE_MASK));
+
+ /* Set divisor and clear phase offset */
+ writel(value, div_addr);
+ writel(0x0, div_addr + WZRD_DR_DIV_TO_PHASE_OFFSET);
+
+ /* Check status register */
+ retries = WZRD_DR_NUM_RETRIES;
+ while (retries--) {
+ if (readl(divider->base + WZRD_DR_STATUS_REG_OFFSET) &
+ WZRD_DR_LOCK_BIT_MASK)
+ break;
+ }
+
+ if (!retries) {
+ err = -ETIMEDOUT;
+ goto err_reconfig;
+ }
+
+ /* Initiate reconfiguration */
+ writel(WZRD_DR_BEGIN_DYNA_RECONF,
+ divider->base + WZRD_DR_INIT_REG_OFFSET);
+
+ /* Check status register */
+ retries = WZRD_DR_NUM_RETRIES;
+ while (retries--) {
+ if (readl(divider->base + WZRD_DR_STATUS_REG_OFFSET) &
+ WZRD_DR_LOCK_BIT_MASK)
+ break;
+ }
+
+ if (!retries)
+ err = -ETIMEDOUT;
+
+err_reconfig:
+ if (divider->lock)
+ spin_unlock_irqrestore(divider->lock, flags);
+ else
+ __release(divider->lock);
+
+ return err;
+}
+
+static long clk_wzrd_round_rate_f(struct clk_hw *hw, unsigned long rate,
+ unsigned long *prate)
+{
+ return rate;
+}
+
+static const struct clk_ops clk_wzrd_clk_divider_ops_f = {
+ .round_rate = clk_wzrd_round_rate_f,
+ .set_rate = clk_wzrd_dynamic_reconfig_f,
+ .recalc_rate = clk_wzrd_recalc_ratef,
+};
+
+static struct clk *clk_wzrd_register_divf(struct device *dev,
+ const char *name,
+ const char *parent_name,
+ unsigned long flags,
+ void __iomem *base, u16 offset,
+ u8 shift, u8 width,
+ u8 clk_divider_flags,
+ const struct clk_div_table *table,
+ spinlock_t *lock)
+{
+ struct clk_wzrd_divider *div;
+ struct clk_hw *hw;
+ struct clk_init_data init;
+ int ret;
+
+ if (clk_divider_flags & CLK_DIVIDER_HIWORD_MASK) {
+ if (width + shift > 16) {
+ pr_warn("divider value exceeds LOWORD field\n");
+ return ERR_PTR(-EINVAL);
+ }
+ }
+
+ /* allocate the divider */
+ div = kzalloc(sizeof(*div), GFP_KERNEL);
+ if (!div)
+ return ERR_PTR(-ENOMEM);
+
+ init.name = name;
+
+ if (clk_divider_flags & CLK_DIVIDER_READ_ONLY)
+ init.ops = &clk_divider_ro_ops;
+ else
+ init.ops = &clk_wzrd_clk_divider_ops_f;
+
+ init.flags = flags;
+ init.parent_names = (parent_name ? &parent_name : NULL);
+ init.num_parents = (parent_name ? 1 : 0);
+
+ /* struct clk_divider assignments */
+ div->base = base;
+ div->offset = offset;
+ div->shift = shift;
+ div->width = width;
+ div->flags = clk_divider_flags;
+ div->lock = lock;
+ div->hw.init = &init;
+ div->table = table;
+
+ /* register the clock */
+ hw = &div->hw;
+ ret = clk_hw_register(dev, hw);
+ if (ret) {
+ kfree(div);
+ return ERR_PTR(ret);
+ }
+
+ return hw->clk;
+}
+
static struct clk *clk_wzrd_register_divider(struct device *dev,
const char *name,
const char *parent_name,
@@ -244,7 +404,7 @@ static struct clk *clk_wzrd_register_divider(struct device *dev,
init.ops = &clk_divider_ro_ops;
else
init.ops = &clk_wzrd_clk_divider_ops;
- init.flags = flags | CLK_IS_BASIC;
+ init.flags = flags;
init.parent_names = (parent_name ? &parent_name : NULL);
init.num_parents = (parent_name ? 1 : 0);
@@ -330,7 +490,7 @@ static SIMPLE_DEV_PM_OPS(clk_wzrd_dev_pm_ops, clk_wzrd_suspend,
static int clk_wzrd_probe(struct platform_device *pdev)
{
int i, ret;
- u32 reg;
+ u32 reg, reg_f, mult;
unsigned long rate;
const char *clk_name;
struct clk_wzrd *clk_wzrd;
@@ -382,17 +542,13 @@ static int clk_wzrd_probe(struct platform_device *pdev)
goto err_disable_clk;
}
- /* we don't support fractional div/mul yet */
- reg = readl(clk_wzrd->base + WZRD_CLK_CFG_REG(0)) &
- WZRD_CLKFBOUT_FRAC_EN;
- reg |= readl(clk_wzrd->base + WZRD_CLK_CFG_REG(2)) &
- WZRD_CLKOUT0_FRAC_EN;
- if (reg)
- dev_warn(&pdev->dev, "fractional div/mul not supported\n");
-
/* register multiplier */
reg = (readl(clk_wzrd->base + WZRD_CLK_CFG_REG(0)) &
WZRD_CLKFBOUT_MULT_MASK) >> WZRD_CLKFBOUT_MULT_SHIFT;
+ reg_f = (readl(clk_wzrd->base + WZRD_CLK_CFG_REG(0)) &
+ WZRD_CLKFBOUT_FRAC_MASK) >> WZRD_CLKFBOUT_FRAC_SHIFT;
+
+ mult = ((reg * 1000) + reg_f);
clk_name = kasprintf(GFP_KERNEL, "%s_mul", dev_name(&pdev->dev));
if (!clk_name) {
ret = -ENOMEM;
@@ -401,7 +557,7 @@ static int clk_wzrd_probe(struct platform_device *pdev)
clk_wzrd->clks_internal[wzrd_clk_mul] = clk_register_fixed_factor
(&pdev->dev, clk_name,
__clk_get_name(clk_wzrd->clk_in1),
- 0, reg, 1);
+ 0, mult, 1000);
kfree(clk_name);
if (IS_ERR(clk_wzrd->clks_internal[wzrd_clk_mul])) {
dev_err(&pdev->dev, "unable to register fixed-factor clock\n");
@@ -440,8 +596,18 @@ static int clk_wzrd_probe(struct platform_device *pdev)
ret = -EINVAL;
goto err_rm_int_clks;
}
- clk_wzrd->clkout[i] = clk_wzrd_register_divider(&pdev->dev,
- clkout_name,
+ if (!i)
+ clk_wzrd->clkout[i] = clk_wzrd_register_divf
+ (&pdev->dev, clkout_name,
+ clk_name, 0,
+ clk_wzrd->base, (WZRD_CLK_CFG_REG(2) + i * 12),
+ WZRD_CLKOUT_DIVIDE_SHIFT,
+ WZRD_CLKOUT_DIVIDE_WIDTH,
+ CLK_DIVIDER_ONE_BASED | CLK_DIVIDER_ALLOW_ZERO,
+ NULL, &clkwzrd_lock);
+ else
+ clk_wzrd->clkout[i] = clk_wzrd_register_divider
+ (&pdev->dev, clkout_name,
clk_name, 0,
clk_wzrd->base, (WZRD_CLK_CFG_REG(2) + i * 12),
WZRD_CLKOUT_DIVIDE_SHIFT,
--
2.1.1
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH v4 6/8] clk: clock-wizard: Remove the hardcoding of the clock outputs
2020-06-26 12:41 [PATCH v4 0/8] clk: clockwizard: Driver updates Shubhrajyoti Datta
` (4 preceding siblings ...)
2020-06-26 12:41 ` [PATCH v4 5/8] clk: clock-wizard: Add support for fractional support Shubhrajyoti Datta
@ 2020-06-26 12:41 ` Shubhrajyoti Datta
2020-06-26 12:41 ` [PATCH v4 7/8] clk: clock-wizard: Update the fixed factor divisors Shubhrajyoti Datta
2020-06-26 12:41 ` [PATCH v4 8/8] staging: clocking-wizard: Delete the driver from the staging Shubhrajyoti Datta
7 siblings, 0 replies; 10+ messages in thread
From: Shubhrajyoti Datta @ 2020-06-26 12:41 UTC (permalink / raw)
To: linux-clk
Cc: sboyd, robh+dt, gregkh, shubhrajyoti.datta, devicetree,
linux-kernel, michals, Shubhrajyoti Datta
The number of output clocks are configurable in the hardware.
Currently the driver registers the maximum number of outputs.
Fix the same by registering only the outputs that are there.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
---
v4:
Assign output in this patch
drivers/clk/clk-xlnx-clock-wizard.c | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
diff --git a/drivers/clk/clk-xlnx-clock-wizard.c b/drivers/clk/clk-xlnx-clock-wizard.c
index 8a7f9bb..28bbaa0 100644
--- a/drivers/clk/clk-xlnx-clock-wizard.c
+++ b/drivers/clk/clk-xlnx-clock-wizard.c
@@ -495,6 +495,7 @@ static int clk_wzrd_probe(struct platform_device *pdev)
const char *clk_name;
struct clk_wzrd *clk_wzrd;
struct resource *mem;
+ int outputs;
struct device_node *np = pdev->dev.of_node;
clk_wzrd = devm_kzalloc(&pdev->dev, sizeof(*clk_wzrd), GFP_KERNEL);
@@ -565,6 +566,7 @@ static int clk_wzrd_probe(struct platform_device *pdev)
goto err_disable_clk;
}
+ outputs = of_property_count_strings(np, "clock-output-names");
/* register div */
reg = (readl(clk_wzrd->base + WZRD_CLK_CFG_REG(0)) &
WZRD_DIVCLK_DIVIDE_MASK) >> WZRD_DIVCLK_DIVIDE_SHIFT;
@@ -586,7 +588,7 @@ static int clk_wzrd_probe(struct platform_device *pdev)
}
/* register div per output */
- for (i = WZRD_NUM_OUTPUTS - 1; i >= 0 ; i--) {
+ for (i = outputs - 1; i >= 0 ; i--) {
const char *clkout_name;
if (of_property_read_string_index(np, "clock-output-names", i,
@@ -617,7 +619,7 @@ static int clk_wzrd_probe(struct platform_device *pdev)
if (IS_ERR(clk_wzrd->clkout[i])) {
int j;
- for (j = i + 1; j < WZRD_NUM_OUTPUTS; j++)
+ for (j = i + 1; j < outputs; j++)
clk_unregister(clk_wzrd->clkout[j]);
dev_err(&pdev->dev,
"unable to register divider clock\n");
--
2.1.1
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH v4 7/8] clk: clock-wizard: Update the fixed factor divisors
2020-06-26 12:41 [PATCH v4 0/8] clk: clockwizard: Driver updates Shubhrajyoti Datta
` (5 preceding siblings ...)
2020-06-26 12:41 ` [PATCH v4 6/8] clk: clock-wizard: Remove the hardcoding of the clock outputs Shubhrajyoti Datta
@ 2020-06-26 12:41 ` Shubhrajyoti Datta
2020-06-26 12:41 ` [PATCH v4 8/8] staging: clocking-wizard: Delete the driver from the staging Shubhrajyoti Datta
7 siblings, 0 replies; 10+ messages in thread
From: Shubhrajyoti Datta @ 2020-06-26 12:41 UTC (permalink / raw)
To: linux-clk
Cc: sboyd, robh+dt, gregkh, shubhrajyoti.datta, devicetree,
linux-kernel, michals, Shubhrajyoti Datta
Update the fixed factor clock registration to register the divisors.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
---
drivers/clk/clk-xlnx-clock-wizard.c | 13 ++++++++-----
1 file changed, 8 insertions(+), 5 deletions(-)
diff --git a/drivers/clk/clk-xlnx-clock-wizard.c b/drivers/clk/clk-xlnx-clock-wizard.c
index 28bbaa0..333ada78 100644
--- a/drivers/clk/clk-xlnx-clock-wizard.c
+++ b/drivers/clk/clk-xlnx-clock-wizard.c
@@ -493,9 +493,11 @@ static int clk_wzrd_probe(struct platform_device *pdev)
u32 reg, reg_f, mult;
unsigned long rate;
const char *clk_name;
+ void __iomem *ctrl_reg;
struct clk_wzrd *clk_wzrd;
struct resource *mem;
int outputs;
+ unsigned long flags = 0;
struct device_node *np = pdev->dev.of_node;
clk_wzrd = devm_kzalloc(&pdev->dev, sizeof(*clk_wzrd), GFP_KERNEL);
@@ -567,16 +569,17 @@ static int clk_wzrd_probe(struct platform_device *pdev)
}
outputs = of_property_count_strings(np, "clock-output-names");
- /* register div */
- reg = (readl(clk_wzrd->base + WZRD_CLK_CFG_REG(0)) &
- WZRD_DIVCLK_DIVIDE_MASK) >> WZRD_DIVCLK_DIVIDE_SHIFT;
+ if (outputs == 1)
+ flags = CLK_SET_RATE_PARENT;
clk_name = kasprintf(GFP_KERNEL, "%s_mul_div", dev_name(&pdev->dev));
if (!clk_name) {
ret = -ENOMEM;
goto err_rm_int_clk;
}
- clk_wzrd->clks_internal[wzrd_clk_mul_div] = clk_register_fixed_factor
+ ctrl_reg = clk_wzrd->base + WZRD_CLK_CFG_REG(0);
+ /* register div */
+ clk_wzrd->clks_internal[wzrd_clk_mul_div] = clk_register_divider
(&pdev->dev, clk_name,
__clk_get_name(clk_wzrd->clks_internal[wzrd_clk_mul]),
flags, ctrl_reg, 0, 8, CLK_DIVIDER_ONE_BASED |
@@ -601,7 +604,7 @@ static int clk_wzrd_probe(struct platform_device *pdev)
if (!i)
clk_wzrd->clkout[i] = clk_wzrd_register_divf
(&pdev->dev, clkout_name,
- clk_name, 0,
+ clk_name, flags,
clk_wzrd->base, (WZRD_CLK_CFG_REG(2) + i * 12),
WZRD_CLKOUT_DIVIDE_SHIFT,
WZRD_CLKOUT_DIVIDE_WIDTH,
--
2.1.1
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH v4 8/8] staging: clocking-wizard: Delete the driver from the staging
2020-06-26 12:41 [PATCH v4 0/8] clk: clockwizard: Driver updates Shubhrajyoti Datta
` (6 preceding siblings ...)
2020-06-26 12:41 ` [PATCH v4 7/8] clk: clock-wizard: Update the fixed factor divisors Shubhrajyoti Datta
@ 2020-06-26 12:41 ` Shubhrajyoti Datta
2020-06-26 13:45 ` Greg KH
7 siblings, 1 reply; 10+ messages in thread
From: Shubhrajyoti Datta @ 2020-06-26 12:41 UTC (permalink / raw)
To: linux-clk
Cc: sboyd, robh+dt, gregkh, shubhrajyoti.datta, devicetree,
linux-kernel, michals, Shubhrajyoti Datta
Delete the driver from the staging as it is in drivers/clk.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
---
drivers/staging/Kconfig | 2 -
drivers/staging/Makefile | 1 -
drivers/staging/clocking-wizard/Kconfig | 10 -
drivers/staging/clocking-wizard/Makefile | 2 -
drivers/staging/clocking-wizard/TODO | 12 -
.../clocking-wizard/clk-xlnx-clock-wizard.c | 333 ---------------------
drivers/staging/clocking-wizard/dt-binding.txt | 30 --
7 files changed, 390 deletions(-)
delete mode 100644 drivers/staging/clocking-wizard/Kconfig
delete mode 100644 drivers/staging/clocking-wizard/Makefile
delete mode 100644 drivers/staging/clocking-wizard/TODO
delete mode 100644 drivers/staging/clocking-wizard/clk-xlnx-clock-wizard.c
delete mode 100644 drivers/staging/clocking-wizard/dt-binding.txt
diff --git a/drivers/staging/Kconfig b/drivers/staging/Kconfig
index 4ec5528..cdb5422 100644
--- a/drivers/staging/Kconfig
+++ b/drivers/staging/Kconfig
@@ -78,8 +78,6 @@ source "drivers/staging/gs_fpgaboot/Kconfig"
source "drivers/staging/unisys/Kconfig"
-source "drivers/staging/clocking-wizard/Kconfig"
-
source "drivers/staging/fbtft/Kconfig"
source "drivers/staging/fsl-dpaa2/Kconfig"
diff --git a/drivers/staging/Makefile b/drivers/staging/Makefile
index 4d34198..14570e5 100644
--- a/drivers/staging/Makefile
+++ b/drivers/staging/Makefile
@@ -29,7 +29,6 @@ obj-$(CONFIG_FIREWIRE_SERIAL) += fwserial/
obj-$(CONFIG_GOLDFISH) += goldfish/
obj-$(CONFIG_GS_FPGABOOT) += gs_fpgaboot/
obj-$(CONFIG_UNISYSSPAR) += unisys/
-obj-$(CONFIG_COMMON_CLK_XLNX_CLKWZRD) += clocking-wizard/
obj-$(CONFIG_FB_TFT) += fbtft/
obj-$(CONFIG_FSL_DPAA2) += fsl-dpaa2/
obj-$(CONFIG_WILC1000) += wilc1000/
diff --git a/drivers/staging/clocking-wizard/Kconfig b/drivers/staging/clocking-wizard/Kconfig
deleted file mode 100644
index 04be22d..0000000
--- a/drivers/staging/clocking-wizard/Kconfig
+++ /dev/null
@@ -1,10 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-#
-# Xilinx Clocking Wizard Driver
-#
-
-config COMMON_CLK_XLNX_CLKWZRD
- tristate "Xilinx Clocking Wizard"
- depends on COMMON_CLK && OF
- help
- Support for the Xilinx Clocking Wizard IP core clock generator.
diff --git a/drivers/staging/clocking-wizard/Makefile b/drivers/staging/clocking-wizard/Makefile
deleted file mode 100644
index b1f9152..0000000
--- a/drivers/staging/clocking-wizard/Makefile
+++ /dev/null
@@ -1,2 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-obj-$(CONFIG_COMMON_CLK_XLNX_CLKWZRD) += clk-xlnx-clock-wizard.o
diff --git a/drivers/staging/clocking-wizard/TODO b/drivers/staging/clocking-wizard/TODO
deleted file mode 100644
index ebe99db..0000000
--- a/drivers/staging/clocking-wizard/TODO
+++ /dev/null
@@ -1,12 +0,0 @@
-TODO:
- - support for fractional multiplier
- - support for fractional divider (output 0 only)
- - support for set_rate() operations (may benefit from Stephen Boyd's
- refactoring of the clk primitives: https://lkml.org/lkml/2014/9/5/766)
- - review arithmetic
- - overflow after multiplication?
- - maximize accuracy before divisions
-
-Patches to:
- Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Sören Brinkmann <soren.brinkmann@xilinx.com>
diff --git a/drivers/staging/clocking-wizard/clk-xlnx-clock-wizard.c b/drivers/staging/clocking-wizard/clk-xlnx-clock-wizard.c
deleted file mode 100644
index e52a64b..0000000
--- a/drivers/staging/clocking-wizard/clk-xlnx-clock-wizard.c
+++ /dev/null
@@ -1,333 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Xilinx 'Clocking Wizard' driver
- *
- * Copyright (C) 2013 - 2014 Xilinx
- *
- * Sören Brinkmann <soren.brinkmann@xilinx.com>
- */
-
-#include <linux/platform_device.h>
-#include <linux/clk.h>
-#include <linux/clk-provider.h>
-#include <linux/slab.h>
-#include <linux/io.h>
-#include <linux/of.h>
-#include <linux/module.h>
-#include <linux/err.h>
-
-#define WZRD_NUM_OUTPUTS 7
-#define WZRD_ACLK_MAX_FREQ 250000000UL
-
-#define WZRD_CLK_CFG_REG(n) (0x200 + 4 * (n))
-
-#define WZRD_CLKOUT0_FRAC_EN BIT(18)
-#define WZRD_CLKFBOUT_FRAC_EN BIT(26)
-
-#define WZRD_CLKFBOUT_MULT_SHIFT 8
-#define WZRD_CLKFBOUT_MULT_MASK (0xff << WZRD_CLKFBOUT_MULT_SHIFT)
-#define WZRD_DIVCLK_DIVIDE_SHIFT 0
-#define WZRD_DIVCLK_DIVIDE_MASK (0xff << WZRD_DIVCLK_DIVIDE_SHIFT)
-#define WZRD_CLKOUT_DIVIDE_SHIFT 0
-#define WZRD_CLKOUT_DIVIDE_MASK (0xff << WZRD_DIVCLK_DIVIDE_SHIFT)
-
-enum clk_wzrd_int_clks {
- wzrd_clk_mul,
- wzrd_clk_mul_div,
- wzrd_clk_int_max
-};
-
-/**
- * struct clk_wzrd:
- * @clk_data: Clock data
- * @nb: Notifier block
- * @base: Memory base
- * @clk_in1: Handle to input clock 'clk_in1'
- * @axi_clk: Handle to input clock 's_axi_aclk'
- * @clks_internal: Internal clocks
- * @clkout: Output clocks
- * @speed_grade: Speed grade of the device
- * @suspended: Flag indicating power state of the device
- */
-struct clk_wzrd {
- struct clk_onecell_data clk_data;
- struct notifier_block nb;
- void __iomem *base;
- struct clk *clk_in1;
- struct clk *axi_clk;
- struct clk *clks_internal[wzrd_clk_int_max];
- struct clk *clkout[WZRD_NUM_OUTPUTS];
- unsigned int speed_grade;
- bool suspended;
-};
-
-#define to_clk_wzrd(_nb) container_of(_nb, struct clk_wzrd, nb)
-
-/* maximum frequencies for input/output clocks per speed grade */
-static const unsigned long clk_wzrd_max_freq[] = {
- 800000000UL,
- 933000000UL,
- 1066000000UL
-};
-
-static int clk_wzrd_clk_notifier(struct notifier_block *nb, unsigned long event,
- void *data)
-{
- unsigned long max;
- struct clk_notifier_data *ndata = data;
- struct clk_wzrd *clk_wzrd = to_clk_wzrd(nb);
-
- if (clk_wzrd->suspended)
- return NOTIFY_OK;
-
- if (ndata->clk == clk_wzrd->clk_in1)
- max = clk_wzrd_max_freq[clk_wzrd->speed_grade - 1];
- else if (ndata->clk == clk_wzrd->axi_clk)
- max = WZRD_ACLK_MAX_FREQ;
- else
- return NOTIFY_DONE; /* should never happen */
-
- switch (event) {
- case PRE_RATE_CHANGE:
- if (ndata->new_rate > max)
- return NOTIFY_BAD;
- return NOTIFY_OK;
- case POST_RATE_CHANGE:
- case ABORT_RATE_CHANGE:
- default:
- return NOTIFY_DONE;
- }
-}
-
-static int __maybe_unused clk_wzrd_suspend(struct device *dev)
-{
- struct clk_wzrd *clk_wzrd = dev_get_drvdata(dev);
-
- clk_disable_unprepare(clk_wzrd->axi_clk);
- clk_wzrd->suspended = true;
-
- return 0;
-}
-
-static int __maybe_unused clk_wzrd_resume(struct device *dev)
-{
- int ret;
- struct clk_wzrd *clk_wzrd = dev_get_drvdata(dev);
-
- ret = clk_prepare_enable(clk_wzrd->axi_clk);
- if (ret) {
- dev_err(dev, "unable to enable s_axi_aclk\n");
- return ret;
- }
-
- clk_wzrd->suspended = false;
-
- return 0;
-}
-
-static SIMPLE_DEV_PM_OPS(clk_wzrd_dev_pm_ops, clk_wzrd_suspend,
- clk_wzrd_resume);
-
-static int clk_wzrd_probe(struct platform_device *pdev)
-{
- int i, ret;
- u32 reg;
- unsigned long rate;
- const char *clk_name;
- struct clk_wzrd *clk_wzrd;
- struct device_node *np = pdev->dev.of_node;
-
- clk_wzrd = devm_kzalloc(&pdev->dev, sizeof(*clk_wzrd), GFP_KERNEL);
- if (!clk_wzrd)
- return -ENOMEM;
- platform_set_drvdata(pdev, clk_wzrd);
-
- clk_wzrd->base = devm_platform_ioremap_resource(pdev, 0);
- if (IS_ERR(clk_wzrd->base))
- return PTR_ERR(clk_wzrd->base);
-
- ret = of_property_read_u32(np, "speed-grade", &clk_wzrd->speed_grade);
- if (!ret) {
- if (clk_wzrd->speed_grade < 1 || clk_wzrd->speed_grade > 3) {
- dev_warn(&pdev->dev, "invalid speed grade '%d'\n",
- clk_wzrd->speed_grade);
- clk_wzrd->speed_grade = 0;
- }
- }
-
- clk_wzrd->clk_in1 = devm_clk_get(&pdev->dev, "clk_in1");
- if (IS_ERR(clk_wzrd->clk_in1)) {
- if (clk_wzrd->clk_in1 != ERR_PTR(-EPROBE_DEFER))
- dev_err(&pdev->dev, "clk_in1 not found\n");
- return PTR_ERR(clk_wzrd->clk_in1);
- }
-
- clk_wzrd->axi_clk = devm_clk_get(&pdev->dev, "s_axi_aclk");
- if (IS_ERR(clk_wzrd->axi_clk)) {
- if (clk_wzrd->axi_clk != ERR_PTR(-EPROBE_DEFER))
- dev_err(&pdev->dev, "s_axi_aclk not found\n");
- return PTR_ERR(clk_wzrd->axi_clk);
- }
- ret = clk_prepare_enable(clk_wzrd->axi_clk);
- if (ret) {
- dev_err(&pdev->dev, "enabling s_axi_aclk failed\n");
- return ret;
- }
- rate = clk_get_rate(clk_wzrd->axi_clk);
- if (rate > WZRD_ACLK_MAX_FREQ) {
- dev_err(&pdev->dev, "s_axi_aclk frequency (%lu) too high\n",
- rate);
- ret = -EINVAL;
- goto err_disable_clk;
- }
-
- /* we don't support fractional div/mul yet */
- reg = readl(clk_wzrd->base + WZRD_CLK_CFG_REG(0)) &
- WZRD_CLKFBOUT_FRAC_EN;
- reg |= readl(clk_wzrd->base + WZRD_CLK_CFG_REG(2)) &
- WZRD_CLKOUT0_FRAC_EN;
- if (reg)
- dev_warn(&pdev->dev, "fractional div/mul not supported\n");
-
- /* register multiplier */
- reg = (readl(clk_wzrd->base + WZRD_CLK_CFG_REG(0)) &
- WZRD_CLKFBOUT_MULT_MASK) >> WZRD_CLKFBOUT_MULT_SHIFT;
- clk_name = kasprintf(GFP_KERNEL, "%s_mul", dev_name(&pdev->dev));
- if (!clk_name) {
- ret = -ENOMEM;
- goto err_disable_clk;
- }
- clk_wzrd->clks_internal[wzrd_clk_mul] = clk_register_fixed_factor
- (&pdev->dev, clk_name,
- __clk_get_name(clk_wzrd->clk_in1),
- 0, reg, 1);
- kfree(clk_name);
- if (IS_ERR(clk_wzrd->clks_internal[wzrd_clk_mul])) {
- dev_err(&pdev->dev, "unable to register fixed-factor clock\n");
- ret = PTR_ERR(clk_wzrd->clks_internal[wzrd_clk_mul]);
- goto err_disable_clk;
- }
-
- /* register div */
- reg = (readl(clk_wzrd->base + WZRD_CLK_CFG_REG(0)) &
- WZRD_DIVCLK_DIVIDE_MASK) >> WZRD_DIVCLK_DIVIDE_SHIFT;
- clk_name = kasprintf(GFP_KERNEL, "%s_mul_div", dev_name(&pdev->dev));
- if (!clk_name) {
- ret = -ENOMEM;
- goto err_rm_int_clk;
- }
-
- clk_wzrd->clks_internal[wzrd_clk_mul_div] = clk_register_fixed_factor
- (&pdev->dev, clk_name,
- __clk_get_name(clk_wzrd->clks_internal[wzrd_clk_mul]),
- 0, 1, reg);
- if (IS_ERR(clk_wzrd->clks_internal[wzrd_clk_mul_div])) {
- dev_err(&pdev->dev, "unable to register divider clock\n");
- ret = PTR_ERR(clk_wzrd->clks_internal[wzrd_clk_mul_div]);
- goto err_rm_int_clk;
- }
-
- /* register div per output */
- for (i = WZRD_NUM_OUTPUTS - 1; i >= 0 ; i--) {
- const char *clkout_name;
-
- if (of_property_read_string_index(np, "clock-output-names", i,
- &clkout_name)) {
- dev_err(&pdev->dev,
- "clock output name not specified\n");
- ret = -EINVAL;
- goto err_rm_int_clks;
- }
- reg = readl(clk_wzrd->base + WZRD_CLK_CFG_REG(2) + i * 12);
- reg &= WZRD_CLKOUT_DIVIDE_MASK;
- reg >>= WZRD_CLKOUT_DIVIDE_SHIFT;
- clk_wzrd->clkout[i] = clk_register_fixed_factor
- (&pdev->dev, clkout_name, clk_name, 0, 1, reg);
- if (IS_ERR(clk_wzrd->clkout[i])) {
- int j;
-
- for (j = i + 1; j < WZRD_NUM_OUTPUTS; j++)
- clk_unregister(clk_wzrd->clkout[j]);
- dev_err(&pdev->dev,
- "unable to register divider clock\n");
- ret = PTR_ERR(clk_wzrd->clkout[i]);
- goto err_rm_int_clks;
- }
- }
-
- kfree(clk_name);
-
- clk_wzrd->clk_data.clks = clk_wzrd->clkout;
- clk_wzrd->clk_data.clk_num = ARRAY_SIZE(clk_wzrd->clkout);
- of_clk_add_provider(np, of_clk_src_onecell_get, &clk_wzrd->clk_data);
-
- if (clk_wzrd->speed_grade) {
- clk_wzrd->nb.notifier_call = clk_wzrd_clk_notifier;
-
- ret = clk_notifier_register(clk_wzrd->clk_in1,
- &clk_wzrd->nb);
- if (ret)
- dev_warn(&pdev->dev,
- "unable to register clock notifier\n");
-
- ret = clk_notifier_register(clk_wzrd->axi_clk, &clk_wzrd->nb);
- if (ret)
- dev_warn(&pdev->dev,
- "unable to register clock notifier\n");
- }
-
- return 0;
-
-err_rm_int_clks:
- clk_unregister(clk_wzrd->clks_internal[1]);
-err_rm_int_clk:
- kfree(clk_name);
- clk_unregister(clk_wzrd->clks_internal[0]);
-err_disable_clk:
- clk_disable_unprepare(clk_wzrd->axi_clk);
-
- return ret;
-}
-
-static int clk_wzrd_remove(struct platform_device *pdev)
-{
- int i;
- struct clk_wzrd *clk_wzrd = platform_get_drvdata(pdev);
-
- of_clk_del_provider(pdev->dev.of_node);
-
- for (i = 0; i < WZRD_NUM_OUTPUTS; i++)
- clk_unregister(clk_wzrd->clkout[i]);
- for (i = 0; i < wzrd_clk_int_max; i++)
- clk_unregister(clk_wzrd->clks_internal[i]);
-
- if (clk_wzrd->speed_grade) {
- clk_notifier_unregister(clk_wzrd->axi_clk, &clk_wzrd->nb);
- clk_notifier_unregister(clk_wzrd->clk_in1, &clk_wzrd->nb);
- }
-
- clk_disable_unprepare(clk_wzrd->axi_clk);
-
- return 0;
-}
-
-static const struct of_device_id clk_wzrd_ids[] = {
- { .compatible = "xlnx,clocking-wizard" },
- { },
-};
-MODULE_DEVICE_TABLE(of, clk_wzrd_ids);
-
-static struct platform_driver clk_wzrd_driver = {
- .driver = {
- .name = "clk-wizard",
- .of_match_table = clk_wzrd_ids,
- .pm = &clk_wzrd_dev_pm_ops,
- },
- .probe = clk_wzrd_probe,
- .remove = clk_wzrd_remove,
-};
-module_platform_driver(clk_wzrd_driver);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Soeren Brinkmann <soren.brinkmann@xilinx.com");
-MODULE_DESCRIPTION("Driver for the Xilinx Clocking Wizard IP core");
diff --git a/drivers/staging/clocking-wizard/dt-binding.txt b/drivers/staging/clocking-wizard/dt-binding.txt
deleted file mode 100644
index 723271e..0000000
--- a/drivers/staging/clocking-wizard/dt-binding.txt
+++ /dev/null
@@ -1,30 +0,0 @@
-Binding for Xilinx Clocking Wizard IP Core
-
-This binding uses the common clock binding[1]. Details about the devices can be
-found in the product guide[2].
-
-[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
-[2] Clocking Wizard Product Guide
-http://www.xilinx.com/support/documentation/ip_documentation/clk_wiz/v5_1/pg065-clk-wiz.pdf
-
-Required properties:
- - compatible: Must be 'xlnx,clocking-wizard'
- - reg: Base and size of the cores register space
- - clocks: Handle to input clock
- - clock-names: Tuple containing 'clk_in1' and 's_axi_aclk'
- - clock-output-names: Names for the output clocks
-
-Optional properties:
- - speed-grade: Speed grade of the device (valid values are 1..3)
-
-Example:
- clock-generator@40040000 {
- reg = <0x40040000 0x1000>;
- compatible = "xlnx,clocking-wizard";
- speed-grade = <1>;
- clock-names = "clk_in1", "s_axi_aclk";
- clocks = <&clkc 15>, <&clkc 15>;
- clock-output-names = "clk_out0", "clk_out1", "clk_out2",
- "clk_out3", "clk_out4", "clk_out5",
- "clk_out6", "clk_out7";
- };
--
2.1.1
^ permalink raw reply related [flat|nested] 10+ messages in thread* Re: [PATCH v4 8/8] staging: clocking-wizard: Delete the driver from the staging
2020-06-26 12:41 ` [PATCH v4 8/8] staging: clocking-wizard: Delete the driver from the staging Shubhrajyoti Datta
@ 2020-06-26 13:45 ` Greg KH
0 siblings, 0 replies; 10+ messages in thread
From: Greg KH @ 2020-06-26 13:45 UTC (permalink / raw)
To: Shubhrajyoti Datta
Cc: linux-clk, sboyd, robh+dt, shubhrajyoti.datta, devicetree,
linux-kernel, michals
On Fri, Jun 26, 2020 at 06:11:44PM +0530, Shubhrajyoti Datta wrote:
> Delete the driver from the staging as it is in drivers/clk.
>
> Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
^ permalink raw reply [flat|nested] 10+ messages in thread