[PATCH v8 0/9] ARM: dts: DRA7: Add dt nodes for PWMSS

[PATCH v8 0/9] ARM: dts: DRA7: Add dt nodes for PWMSS

[Franklin S Cooper Jr]

This patch series adds support for PWM for DRA7. The IP is the same as the
one present in AM33XX and AM437XX.

However, before doing so remove unnecessary hwmod entries for eCAP, ePWM
and eQEP.

The following are the biggest changes from v7 to v8:
Insure DT unit address matches reg property address

The following are the biggest changes from v6 to v7:
* Several patches to document previously undocumented bindings.
* Fix minor issues in binding documents.

The following are the biggest changes from v5 to v6:
* Created two new bindings to allow ECAP and PWM to grab their functional
clock from DT rather than depending on PWMSS parent.
* Pull in a couple of patches from the "Correct PWM bindings" series. This
makes it a bit easier to understand.

>From the two patchsets a handful of patches have already been pulled in by
maintainers and have already made it to linux-next. Therefore, this
patch series is built ontop of the latest linux-next.

Tested on:
AM335x, AM437x and X15 + lcd w/backlight

Franklin S Cooper Jr (8):
  clk: ti: am335x/am4372: Add tbclk to pwm node
  ARM: dts: am437x: Add missing compatibles to PWM binding documents
  pwm: pwm-tiehrpwm: Update dt binding document to use generic node name
  pwm: pwm-tiecap: Update dt binding document to use proper unit address
  ARM: dts: am437x/am33xx/da850: Add new ECAP and EPWM bindings
  pwms: pwm-ti*: Get the clock from the PWMSS parent when using old
    bindings
  ARM: dts: am437x/am33xx: Remove hwmod entries for ECAP and EPWM nodes
  ARM: AM335x/AM437x: hwmod: Remove eQEP, ePWM and eCAP hwmod entries

Vignesh R (1):
  ARM: dts: DRA7: Add dt nodes for PWMSS

 .../devicetree/bindings/pwm/pwm-tiecap.txt         | 38 ++++++---
 .../devicetree/bindings/pwm/pwm-tiehrpwm.txt       | 38 ++++++---
 .../devicetree/bindings/pwm/pwm-tipwmss.txt        | 33 +++++++-
 arch/arm/boot/dts/am33xx.dtsi                      | 36 ++++++---
 arch/arm/boot/dts/am4372.dtsi                      | 63 ++++++++++-----
 arch/arm/boot/dts/da850.dtsi                       | 15 ++--
 arch/arm/boot/dts/dra7.dtsi                        | 90 ++++++++++++++++++++++
 .../mach-omap2/omap_hwmod_33xx_43xx_common_data.h  | 18 -----
 .../omap_hwmod_33xx_43xx_interconnect_data.c       | 64 ---------------
 .../mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c | 84 --------------------
 arch/arm/mach-omap2/omap_hwmod_33xx_data.c         |  9 ---
 arch/arm/mach-omap2/omap_hwmod_43xx_data.c         | 54 -------------
 drivers/clk/ti/clk-33xx.c                          |  3 +
 drivers/clk/ti/clk-43xx.c                          |  6 ++
 drivers/pwm/pwm-tiecap.c                           |  7 ++
 drivers/pwm/pwm-tiehrpwm.c                         |  7 ++
 16 files changed, 281 insertions(+), 284 deletions(-)

-- 
2.7.0

[PATCH v8 1/9] clk: ti: am335x/am4372: Add tbclk to pwm node

[Franklin S Cooper Jr]

Add tblck to the pwm nodes. This insures that the ehrpwm driver has access
to the time-based clk.

Do not remove similar entries for ehrpwm node. Later patches will switch
from using ehrpwm node name to pwm. But to maintain ABI compatibility we
shouldn't remove the old entries.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
---
 drivers/clk/ti/clk-33xx.c | 3 +++
 drivers/clk/ti/clk-43xx.c | 6 ++++++
 2 files changed, 9 insertions(+)

diff --git a/drivers/clk/ti/clk-33xx.c b/drivers/clk/ti/clk-33xx.c
index ef2ec64..0e47d95 100644
--- a/drivers/clk/ti/clk-33xx.c
+++ b/drivers/clk/ti/clk-33xx.c
@@ -108,6 +108,9 @@ static struct ti_dt_clk am33xx_clks[] = {
 	DT_CLK("48300200.ehrpwm", "tbclk", "ehrpwm0_tbclk"),
 	DT_CLK("48302200.ehrpwm", "tbclk", "ehrpwm1_tbclk"),
 	DT_CLK("48304200.ehrpwm", "tbclk", "ehrpwm2_tbclk"),
+	DT_CLK("48300200.pwm", "tbclk", "ehrpwm0_tbclk"),
+	DT_CLK("48302200.pwm", "tbclk", "ehrpwm1_tbclk"),
+	DT_CLK("48304200.pwm", "tbclk", "ehrpwm2_tbclk"),
 	{ .node_name = NULL },
 };
 
diff --git a/drivers/clk/ti/clk-43xx.c b/drivers/clk/ti/clk-43xx.c
index 097fc90..7255aa8 100644
--- a/drivers/clk/ti/clk-43xx.c
+++ b/drivers/clk/ti/clk-43xx.c
@@ -115,6 +115,12 @@ static struct ti_dt_clk am43xx_clks[] = {
 	DT_CLK("48306200.ehrpwm", "tbclk", "ehrpwm3_tbclk"),
 	DT_CLK("48308200.ehrpwm", "tbclk", "ehrpwm4_tbclk"),
 	DT_CLK("4830a200.ehrpwm", "tbclk", "ehrpwm5_tbclk"),
+	DT_CLK("48300200.pwm", "tbclk", "ehrpwm0_tbclk"),
+	DT_CLK("48302200.pwm", "tbclk", "ehrpwm1_tbclk"),
+	DT_CLK("48304200.pwm", "tbclk", "ehrpwm2_tbclk"),
+	DT_CLK("48306200.pwm", "tbclk", "ehrpwm3_tbclk"),
+	DT_CLK("48308200.pwm", "tbclk", "ehrpwm4_tbclk"),
+	DT_CLK("4830a200.pwm", "tbclk", "ehrpwm5_tbclk"),
 	{ .node_name = NULL },
 };
 
-- 
2.7.0

[PATCH v8 2/9] ARM: dts: am437x: Add missing compatibles to PWM binding documents

[Franklin S Cooper Jr]

There are several SOC specific compatibles for ECAP, EHRPWM and PWMMS
that are in use but aren't properly documented. Therefore, fix this
by adding the compatibles to the appropriate binding documents.

While at it make minor corrections to the binding document.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 .../devicetree/bindings/pwm/pwm-tiecap.txt          | 12 ++++++++++--
 .../devicetree/bindings/pwm/pwm-tiehrpwm.txt        | 12 ++++++++++--
 .../devicetree/bindings/pwm/pwm-tipwmss.txt         | 21 +++++++++++++++++++--
 3 files changed, 39 insertions(+), 6 deletions(-)

diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
index fb81179..788da6c 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
@@ -2,8 +2,9 @@ TI SOC ECAP based APWM controller
 
 Required properties:
 - compatible: Must be "ti,<soc>-ecap".
-  for am33xx - compatible = "ti,am33xx-ecap";
-  for da850  - compatible = "ti,da850-ecap", "ti,am33xx-ecap";
+  for am33xx  - compatible = "ti,am33xx-ecap";
+  for am4372  - compatible = "ti,am4372-ecap", "ti,am33xx-ecap";
+  for da850   - compatible = "ti,da850-ecap", "ti,am33xx-ecap";
 - #pwm-cells: should be 3. See pwm.txt in this directory for a description of
   the cells format. The PWM channel index ranges from 0 to 4. The only third
   cell flag supported by this binding is PWM_POLARITY_INVERTED.
@@ -22,6 +23,13 @@ ecap0: ecap@0 { /* ECAP on am33xx */
 	ti,hwmods = "ecap0";
 };
 
+ecap0: ecap@0 { /* ECAP on am4372 */
+	compatible = "ti,am4372-ecap", "ti,am33xx-ecap";
+	#pwm-cells = <3>;
+	reg = <0x48300100 0x80>;
+	ti,hwmods = "ecap0";
+};
+
 ecap0: ecap@0 { /* ECAP on da850 */
 	compatible = "ti,da850-ecap", "ti,am33xx-ecap";
 	#pwm-cells = <3>;
diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
index 9c100b2..99b544f 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
@@ -2,8 +2,9 @@ TI SOC EHRPWM based PWM controller
 
 Required properties:
 - compatible: Must be "ti,<soc>-ehrpwm".
-  for am33xx - compatible = "ti,am33xx-ehrpwm";
-  for da850  - compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm";
+  for am33xx  - compatible = "ti,am33xx-ehrpwm";
+  for am4372  - compatible = "ti,am4372-ehrpwm", "ti,am33xx-ehrpwm";
+  for da850   - compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm";
 - #pwm-cells: should be 3. See pwm.txt in this directory for a description of
   the cells format. The only third cell flag supported by this binding is
   PWM_POLARITY_INVERTED.
@@ -22,6 +23,13 @@ ehrpwm0: ehrpwm@0 { /* EHRPWM on am33xx */
 	ti,hwmods = "ehrpwm0";
 };
 
+ehrpwm0: ehrpwm@0 { /* EHRPWM on am4372 */
+	compatible = "ti,am4372-ehrpwm", "ti,am33xx-ehrpwm";
+	#pwm-cells = <3>;
+	reg = <0x48300200 0x80>;
+	ti,hwmods = "ehrpwm0";
+};
+
 ehrpwm0: ehrpwm@0 { /* EHRPWM on da850 */
 	compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm";
 	#pwm-cells = <3>;
diff --git a/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt
index f7eae77..fd8e87c 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt
@@ -1,7 +1,10 @@
 TI SOC based PWM Subsystem
 
 Required properties:
-- compatible: Must be "ti,am33xx-pwmss";
+- compatible: Must be "ti,<soc>-pwmss".
+  for am33xx  - compatible = "ti,am33xx-pwmss";
+  for am4372  - compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
+
 - reg: physical base address and size of the registers map.
 - address-cells: Specify the number of u32 entries needed in child nodes.
 		  Should set to 1.
@@ -16,7 +19,7 @@ Required properties:
 Also child nodes should also populated under PWMSS DT node.
 
 Example:
-pwmss0: pwmss@48300000 {
+epwmss0: epwmss@48300000 { /* PWMSS for am33xx */
 	compatible = "ti,am33xx-pwmss";
 	reg = <0x48300000 0x10>;
 	ti,hwmods = "epwmss0";
@@ -29,3 +32,17 @@ pwmss0: pwmss@48300000 {
 
 	/* child nodes go here */
 };
+
+epwmss0: epwmss@48300000 { /* PWMSS for am4372 */
+	compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"
+	reg = <0x48300000 0x10>;
+	ti,hwmods = "epwmss0";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	status = "disabled";
+	ranges = <0x48300100 0x48300100 0x80   /* ECAP */
+		  0x48300180 0x48300180 0x80   /* EQEP */
+		  0x48300200 0x48300200 0x80>; /* EHRPWM */
+
+	/* child nodes go here */
+};
-- 
2.7.0

[PATCH v8 3/9] pwm: pwm-tiehrpwm: Update dt binding document to use generic node name

[Franklin S Cooper Jr]

Now that the node name has been changed from ehrpwm to pwm the document
should show this proper usage. Change the unit address in the example
from 0 to the proper physical address value that should be used. Also
insure that the unit address matches to the reg property.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
index 99b544f..f3bc09e 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
@@ -16,22 +16,22 @@ Optional properties:
 
 Example:
 
-ehrpwm0: ehrpwm@0 { /* EHRPWM on am33xx */
+ehrpwm0: pwm@48300200 { /* EHRPWM on am33xx */
 	compatible = "ti,am33xx-ehrpwm";
 	#pwm-cells = <3>;
 	reg = <0x48300200 0x100>;
 	ti,hwmods = "ehrpwm0";
 };
 
-ehrpwm0: ehrpwm@0 { /* EHRPWM on am4372 */
+ehrpwm0: pwm@48300200 { /* EHRPWM on am4372 */
 	compatible = "ti,am4372-ehrpwm", "ti,am33xx-ehrpwm";
 	#pwm-cells = <3>;
 	reg = <0x48300200 0x80>;
 	ti,hwmods = "ehrpwm0";
 };
 
-ehrpwm0: ehrpwm@0 { /* EHRPWM on da850 */
+ehrpwm0: pwm@1f00000 { /* EHRPWM on da850 */
 	compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm";
 	#pwm-cells = <3>;
-	reg = <0x300000 0x2000>;
+	reg = <0x1f00000 0x2000>;
 };
-- 
2.7.0

[PATCH v8 4/9] pwm: pwm-tiecap: Update dt binding document to use proper unit address

[Franklin S Cooper Jr]

Replace unit address from 0 to the proper physical address. Also insure
that the unit address matches the reg property address.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
---
 Documentation/devicetree/bindings/pwm/pwm-tiecap.txt | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
index 788da6c..0d47354 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
@@ -16,22 +16,22 @@ Optional properties:
 
 Example:
 
-ecap0: ecap@0 { /* ECAP on am33xx */
+ecap0: ecap@48300100 { /* ECAP on am33xx */
 	compatible = "ti,am33xx-ecap";
 	#pwm-cells = <3>;
 	reg = <0x48300100 0x80>;
 	ti,hwmods = "ecap0";
 };
 
-ecap0: ecap@0 { /* ECAP on am4372 */
+ecap0: ecap@48300100 { /* ECAP on am4372 */
 	compatible = "ti,am4372-ecap", "ti,am33xx-ecap";
 	#pwm-cells = <3>;
 	reg = <0x48300100 0x80>;
 	ti,hwmods = "ecap0";
 };
 
-ecap0: ecap@0 { /* ECAP on da850 */
+ecap0: ecap@1f06000 { /* ECAP on da850 */
 	compatible = "ti,da850-ecap", "ti,am33xx-ecap";
 	#pwm-cells = <3>;
-	reg = <0x306000 0x80>;
+	reg = <0x1f06000 0x80>;
 };
-- 
2.7.0

[PATCH v8 5/9] ARM: dts: am437x/am33xx/da850: Add new ECAP and EPWM bindings

[Franklin S Cooper Jr]

Switch to a new ECAP and EPWM bindings that doesn't depend on hwmod to
provide the various required clocks.

For AM437 and AM335x, add the required clocks explicitly to DT. The
hwmod entries for ECAP and EPWM will be removed and this will prevent
anything from breaking.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 .../devicetree/bindings/pwm/pwm-tiecap.txt         | 18 +++++---
 .../devicetree/bindings/pwm/pwm-tiehrpwm.txt       | 18 +++++---
 arch/arm/boot/dts/am33xx.dtsi                      | 30 +++++++++---
 arch/arm/boot/dts/am4372.dtsi                      | 54 ++++++++++++++++++----
 arch/arm/boot/dts/da850.dtsi                       | 15 ++++--
 5 files changed, 103 insertions(+), 32 deletions(-)

diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
index 0d47354..ee0a8bd 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
@@ -2,9 +2,9 @@ TI SOC ECAP based APWM controller
 
 Required properties:
 - compatible: Must be "ti,<soc>-ecap".
-  for am33xx  - compatible = "ti,am33xx-ecap";
-  for am4372  - compatible = "ti,am4372-ecap", "ti,am33xx-ecap";
-  for da850   - compatible = "ti,da850-ecap", "ti,am33xx-ecap";
+  for am33xx - compatible = "ti,am3352-ecap", "ti,am33xx-ecap";
+  for am4372 - compatible = "ti,am4372-ecap", "ti,am3352-ecap", "ti,am33xx-ecap";
+  for da850  - compatible = "ti,da850-ecap", "ti,am3352-ecap", "ti,am33xx-ecap";
 - #pwm-cells: should be 3. See pwm.txt in this directory for a description of
   the cells format. The PWM channel index ranges from 0 to 4. The only third
   cell flag supported by this binding is PWM_POLARITY_INVERTED.
@@ -13,25 +13,31 @@ Required properties:
 Optional properties:
 - ti,hwmods: Name of the hwmod associated to the ECAP:
   "ecap<x>", <x> being the 0-based instance number from the HW spec
+- clocks: Handle to the ECAP's functional clock.
+- clock-names: Must be set to "fck".
 
 Example:
 
 ecap0: ecap@48300100 { /* ECAP on am33xx */
-	compatible = "ti,am33xx-ecap";
+	compatible = "ti,am3352-ecap", "ti,am33xx-ecap";
 	#pwm-cells = <3>;
 	reg = <0x48300100 0x80>;
 	ti,hwmods = "ecap0";
+	clocks = <&l4ls_gclk>;
+	clock-names = "fck";
 };
 
 ecap0: ecap@48300100 { /* ECAP on am4372 */
-	compatible = "ti,am4372-ecap", "ti,am33xx-ecap";
+	compatible = "ti,am4372-ecap", "ti,am3352-ecap", "ti,am33xx-ecap";
 	#pwm-cells = <3>;
 	reg = <0x48300100 0x80>;
 	ti,hwmods = "ecap0";
+	clocks = <&l4ls_gclk>;
+	clock-names = "fck";
 };
 
 ecap0: ecap@1f06000 { /* ECAP on da850 */
-	compatible = "ti,da850-ecap", "ti,am33xx-ecap";
+	compatible = "ti,da850-ecap", "ti,am3352-ecap", "ti,am33xx-ecap";
 	#pwm-cells = <3>;
 	reg = <0x1f06000 0x80>;
 };
diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
index f3bc09e..e9a156b 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
@@ -2,9 +2,9 @@ TI SOC EHRPWM based PWM controller
 
 Required properties:
 - compatible: Must be "ti,<soc>-ehrpwm".
-  for am33xx  - compatible = "ti,am33xx-ehrpwm";
-  for am4372  - compatible = "ti,am4372-ehrpwm", "ti,am33xx-ehrpwm";
-  for da850   - compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm";
+  for am33xx  - compatible = "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm";
+  for am4372  - compatible = "ti,am4372-ehrpwm", "ti-am3352-ehrpwm", "ti,am33xx-ehrpwm";
+  for da850   - compatible = "ti,da850-ehrpwm", "ti-am3352-ehrpwm", "ti,am33xx-ehrpwm";
 - #pwm-cells: should be 3. See pwm.txt in this directory for a description of
   the cells format. The only third cell flag supported by this binding is
   PWM_POLARITY_INVERTED.
@@ -13,25 +13,31 @@ Required properties:
 Optional properties:
 - ti,hwmods: Name of the hwmod associated to the EHRPWM:
   "ehrpwm<x>", <x> being the 0-based instance number from the HW spec
+- clocks: Handle to the PWM's time-base and functional clock.
+- clock-names: Must be set to "tbclk" and "fck".
 
 Example:
 
 ehrpwm0: pwm@48300200 { /* EHRPWM on am33xx */
-	compatible = "ti,am33xx-ehrpwm";
+	compatible = "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm";
 	#pwm-cells = <3>;
 	reg = <0x48300200 0x100>;
+	clocks = <&ehrpwm0_tbclk>, <&l4ls_gclk>;
+	clock-names = "tbclk", "fck";
 	ti,hwmods = "ehrpwm0";
 };
 
 ehrpwm0: pwm@48300200 { /* EHRPWM on am4372 */
-	compatible = "ti,am4372-ehrpwm", "ti,am33xx-ehrpwm";
+	compatible = "ti,am4372-ehrpwm", "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm";
 	#pwm-cells = <3>;
 	reg = <0x48300200 0x80>;
+	clocks = <&ehrpwm0_tbclk>, <&l4ls_gclk>;
+	clock-names = "tbclk", "fck";
 	ti,hwmods = "ehrpwm0";
 };
 
 ehrpwm0: pwm@1f00000 { /* EHRPWM on da850 */
-	compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm";
+	compatible = "ti,da850-ehrpwm", "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm";
 	#pwm-cells = <3>;
 	reg = <0x1f00000 0x2000>;
 };
diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index 52be48b..999ba2f 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -679,9 +679,12 @@
 				  0x48300200 0x48300200 0x80>; /* EHRPWM */
 
 			ecap0: ecap@48300100 {
-				compatible = "ti,am33xx-ecap";
+				compatible = "ti,am3352-ecap",
+					     "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48300100 0x80>;
+				clocks = <&l4ls_gclk>;
+				clock-names = "fck";
 				interrupts = <31>;
 				interrupt-names = "ecap0";
 				ti,hwmods = "ecap0";
@@ -689,10 +692,13 @@
 			};
 
 			ehrpwm0: pwm@48300200 {
-				compatible = "ti,am33xx-ehrpwm";
+				compatible = "ti,am3352-ehrpwm",
+					     "ti,am33xx-ehrpwm";
 				#pwm-cells = <3>;
 				reg = <0x48300200 0x80>;
 				ti,hwmods = "ehrpwm0";
+				clocks = <&ehrpwm0_tbclk>, <&l4ls_gclk>;
+				clock-names = "tbclk", "fck";
 				status = "disabled";
 			};
 		};
@@ -709,9 +715,12 @@
 				  0x48302200 0x48302200 0x80>; /* EHRPWM */
 
 			ecap1: ecap@48302100 {
-				compatible = "ti,am33xx-ecap";
+				compatible = "ti,am3352-ecap",
+					     "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48302100 0x80>;
+				clocks = <&l4ls_gclk>;
+				clock-names = "fck";
 				interrupts = <47>;
 				interrupt-names = "ecap1";
 				ti,hwmods = "ecap1";
@@ -719,10 +728,13 @@
 			};
 
 			ehrpwm1: pwm@48302200 {
-				compatible = "ti,am33xx-ehrpwm";
+				compatible = "ti,am3352-ehrpwm",
+					     "ti,am33xx-ehrpwm";
 				#pwm-cells = <3>;
 				reg = <0x48302200 0x80>;
 				ti,hwmods = "ehrpwm1";
+				clocks = <&ehrpwm1_tbclk>, <&l4ls_gclk>;
+				clock-names = "tbclk", "fck";
 				status = "disabled";
 			};
 		};
@@ -739,9 +751,12 @@
 				  0x48304200 0x48304200 0x80>; /* EHRPWM */
 
 			ecap2: ecap@48304100 {
-				compatible = "ti,am33xx-ecap";
+				compatible = "ti,am3352-ecap",
+					     "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48304100 0x80>;
+				clocks = <&l4ls_gclk>;
+				clock-names = "fck";
 				interrupts = <61>;
 				interrupt-names = "ecap2";
 				ti,hwmods = "ecap2";
@@ -749,10 +764,13 @@
 			};
 
 			ehrpwm2: pwm@48304200 {
-				compatible = "ti,am33xx-ehrpwm";
+				compatible = "ti,am3352-ehrpwm",
+					     "ti,am33xx-ehrpwm";
 				#pwm-cells = <3>;
 				reg = <0x48304200 0x80>;
 				ti,hwmods = "ehrpwm2";
+				clocks = <&ehrpwm2_tbclk>, <&l4ls_gclk>;
+				clock-names = "tbclk", "fck";
 				status = "disabled";
 			};
 		};
diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
index 12fcde4..e858460 100644
--- a/arch/arm/boot/dts/am4372.dtsi
+++ b/arch/arm/boot/dts/am4372.dtsi
@@ -672,18 +672,26 @@
 			status = "disabled";
 
 			ecap0: ecap@48300100 {
-				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				compatible = "ti,am4372-ecap",
+					     "ti,am3352-ecap",
+					     "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48300100 0x80>;
 				ti,hwmods = "ecap0";
+				clocks = <&l4ls_gclk>;
+				clock-names = "fck";
 				status = "disabled";
 			};
 
 			ehrpwm0: pwm@48300200 {
-				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				compatible = "ti,am4372-ehrpwm",
+					     "ti,am3352-ehrpwm",
+					     "ti,am33xx-ehrpwm";
 				#pwm-cells = <3>;
 				reg = <0x48300200 0x80>;
 				ti,hwmods = "ehrpwm0";
+				clocks = <&ehrpwm0_tbclk>, <&l4ls_gclk>;
+				clock-names = "tbclk", "fck";
 				status = "disabled";
 			};
 		};
@@ -698,18 +706,26 @@
 			status = "disabled";
 
 			ecap1: ecap@48302100 {
-				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				compatible = "ti,am4372-ecap",
+					     "ti,am3352-ecap",
+					     "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48302100 0x80>;
 				ti,hwmods = "ecap1";
+				clocks = <&l4ls_gclk>;
+				clock-names = "fck";
 				status = "disabled";
 			};
 
 			ehrpwm1: pwm@48302200 {
-				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				compatible = "ti,am4372-ehrpwm",
+					     "ti,am3352-ehrpwm",
+					     "ti,am33xx-ehrpwm";
 				#pwm-cells = <3>;
 				reg = <0x48302200 0x80>;
 				ti,hwmods = "ehrpwm1";
+				clocks = <&ehrpwm1_tbclk>, <&l4ls_gclk>;
+				clock-names = "tbclk", "fck";
 				status = "disabled";
 			};
 		};
@@ -724,18 +740,26 @@
 			status = "disabled";
 
 			ecap2: ecap@48304100 {
-				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				compatible = "ti,am4372-ecap",
+					     "ti,am3352-ecap",
+					     "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48304100 0x80>;
+				clocks = <&l4ls_gclk>;
+				clock-names = "fck";
 				ti,hwmods = "ecap2";
 				status = "disabled";
 			};
 
 			ehrpwm2: pwm@48304200 {
-				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				compatible = "ti,am4372-ehrpwm",
+					     "ti,am3352-ehrpwm",
+					     "ti,am33xx-ehrpwm";
 				#pwm-cells = <3>;
 				reg = <0x48304200 0x80>;
 				ti,hwmods = "ehrpwm2";
+				clocks = <&ehrpwm2_tbclk>, <&l4ls_gclk>;
+				clock-names = "tbclk", "fck";
 				status = "disabled";
 			};
 		};
@@ -750,10 +774,14 @@
 			status = "disabled";
 
 			ehrpwm3: pwm@48306200 {
-				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				compatible = "ti,am4372-ehrpwm",
+					     "ti,am3352-ehrpwm",
+					     "ti,am33xx-ehrpwm";
 				#pwm-cells = <3>;
 				reg = <0x48306200 0x80>;
 				ti,hwmods = "ehrpwm3";
+				clocks = <&ehrpwm3_tbclk>, <&l4ls_gclk>;
+				clock-names = "tbclk", "fck";
 				status = "disabled";
 			};
 		};
@@ -768,10 +796,14 @@
 			status = "disabled";
 
 			ehrpwm4: pwm@48308200 {
-				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				compatible = "ti,am4372-ehrpwm",
+					     "ti,am3352-ehrpwm",
+					     "ti,am33xx-ehrpwm";
 				#pwm-cells = <3>;
 				reg = <0x48308200 0x80>;
 				ti,hwmods = "ehrpwm4";
+				clocks = <&ehrpwm4_tbclk>, <&l4ls_gclk>;
+				clock-names = "tbclk", "fck";
 				status = "disabled";
 			};
 		};
@@ -786,9 +818,13 @@
 			status = "disabled";
 
 			ehrpwm5: pwm@4830a200 {
-				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				compatible = "ti,am4372-ehrpwm",
+					     "ti,am3352-ehrpwm",
+					     "ti,am33xx-ehrpwm";
 				#pwm-cells = <3>;
 				reg = <0x4830a200 0x80>;
+				clocks = <&ehrpwm5_tbclk>, <&l4ls_gclk>;
+				clock-names = "tbclk", "fck";
 				ti,hwmods = "ehrpwm5";
 				status = "disabled";
 			};
diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi
index c3910e2..28a1064 100644
--- a/arch/arm/boot/dts/da850.dtsi
+++ b/arch/arm/boot/dts/da850.dtsi
@@ -248,31 +248,36 @@
 			status = "disabled";
 		};
 		ehrpwm0: pwm@01f00000 {
-			compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm";
+			compatible = "ti,da850-ehrpwm", "ti,am3352-ehrpwm",
+				     "ti,am33xx-ehrpwm";
 			#pwm-cells = <3>;
 			reg = <0x300000 0x2000>;
 			status = "disabled";
 		};
 		ehrpwm1: pwm@01f02000 {
-			compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm";
+			compatible = "ti,da850-ehrpwm", "ti,am3352-ehrpwm",
+				     "ti,am33xx-ehrpwm";
 			#pwm-cells = <3>;
 			reg = <0x302000 0x2000>;
 			status = "disabled";
 		};
 		ecap0: ecap@01f06000 {
-			compatible = "ti,da850-ecap", "ti,am33xx-ecap";
+			compatible = "ti,da850-ecap", "ti,am3352-ecap",
+				     "ti,am33xx-ecap";
 			#pwm-cells = <3>;
 			reg = <0x306000 0x80>;
 			status = "disabled";
 		};
 		ecap1: ecap@01f07000 {
-			compatible = "ti,da850-ecap", "ti,am33xx-ecap";
+			compatible = "ti,da850-ecap", "ti,am3352-ecap",
+				     "ti,am33xx-ecap";
 			#pwm-cells = <3>;
 			reg = <0x307000 0x80>;
 			status = "disabled";
 		};
 		ecap2: ecap@01f08000 {
-			compatible = "ti,da850-ecap", "ti,am33xx-ecap";
+			compatible = "ti,da850-ecap", "ti,am3352-ecap",
+				     "ti,am33xx-ecap";
 			#pwm-cells = <3>;
 			reg = <0x308000 0x80>;
 			status = "disabled";
-- 
2.7.0

[PATCH v8 6/9] pwms: pwm-ti*: Get the clock from the PWMSS parent when using old bindings

[Franklin S Cooper Jr]

When using the old eCAP and ePWM bindings for AM335x and AM437x the clock
can be retrieved from the PWMSS parent. Newer bindings will insure that
this clock is provided via device tree.

Therefore, update this driver to support the newer and older bindings. In
the case of the older binding being used give a warning.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
---
 drivers/pwm/pwm-tiecap.c   | 7 +++++++
 drivers/pwm/pwm-tiehrpwm.c | 7 +++++++
 2 files changed, 14 insertions(+)

diff --git a/drivers/pwm/pwm-tiecap.c b/drivers/pwm/pwm-tiecap.c
index 616af76..a0833c8 100644
--- a/drivers/pwm/pwm-tiecap.c
+++ b/drivers/pwm/pwm-tiecap.c
@@ -195,6 +195,7 @@ static const struct pwm_ops ecap_pwm_ops = {
 };
 
 static const struct of_device_id ecap_of_match[] = {
+	{ .compatible	= "ti,am3352-ecap" },
 	{ .compatible	= "ti,am33xx-ecap" },
 	{},
 };
@@ -213,6 +214,12 @@ static int ecap_pwm_probe(struct platform_device *pdev)
 		return -ENOMEM;
 
 	clk = devm_clk_get(&pdev->dev, "fck");
+
+	if (IS_ERR(clk) && of_device_is_compatible(pdev->dev.of_node, "ti,am33xx-ecap")) {
+		dev_warn(&pdev->dev, "Binding is obsolete.\n");
+		clk = devm_clk_get(pdev->dev.parent, "fck");
+	}
+
 	if (IS_ERR(clk)) {
 		dev_err(&pdev->dev, "failed to get clock\n");
 		return PTR_ERR(clk);
diff --git a/drivers/pwm/pwm-tiehrpwm.c b/drivers/pwm/pwm-tiehrpwm.c
index 6a41e66..cee29a2 100644
--- a/drivers/pwm/pwm-tiehrpwm.c
+++ b/drivers/pwm/pwm-tiehrpwm.c
@@ -426,6 +426,7 @@ static const struct pwm_ops ehrpwm_pwm_ops = {
 };
 
 static const struct of_device_id ehrpwm_of_match[] = {
+	{ .compatible	= "ti,am3352-ehrpwm" },
 	{ .compatible	= "ti,am33xx-ehrpwm" },
 	{},
 };
@@ -444,6 +445,12 @@ static int ehrpwm_pwm_probe(struct platform_device *pdev)
 		return -ENOMEM;
 
 	clk = devm_clk_get(&pdev->dev, "fck");
+
+	if (IS_ERR(clk) && of_device_is_compatible(pdev->dev.of_node, "ti,am33xx-ecap")) {
+		dev_warn(&pdev->dev, "Binding is obsolete.\n");
+		clk = devm_clk_get(pdev->dev.parent, "fck");
+	}
+
 	if (IS_ERR(clk)) {
 		dev_err(&pdev->dev, "failed to get clock\n");
 		return PTR_ERR(clk);
-- 
2.7.0

[PATCH v8 7/9] ARM: dts: am437x/am33xx: Remove hwmod entries for ECAP and EPWM nodes

[Franklin S Cooper Jr]

Previous patches switched the ECAP and EPWM to use the new bindings.
These bindings explicitly adds the various required clocks via DT rather
than depending on hwmod.

Therefore, it is safe to remove the hwmod entries since they are no longer
needed.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Paul Walmsley <paul@pwsan.com>
---
 Documentation/devicetree/bindings/pwm/pwm-tiecap.txt   | 3 ---
 Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt | 3 ---
 arch/arm/boot/dts/am33xx.dtsi                          | 6 ------
 arch/arm/boot/dts/am4372.dtsi                          | 9 ---------
 4 files changed, 21 deletions(-)

diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
index ee0a8bd..f2a9a7c 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
@@ -11,8 +11,6 @@ Required properties:
 - reg: physical base address and size of the registers map.
 
 Optional properties:
-- ti,hwmods: Name of the hwmod associated to the ECAP:
-  "ecap<x>", <x> being the 0-based instance number from the HW spec
 - clocks: Handle to the ECAP's functional clock.
 - clock-names: Must be set to "fck".
 
@@ -22,7 +20,6 @@ ecap0: ecap@48300100 { /* ECAP on am33xx */
 	compatible = "ti,am3352-ecap", "ti,am33xx-ecap";
 	#pwm-cells = <3>;
 	reg = <0x48300100 0x80>;
-	ti,hwmods = "ecap0";
 	clocks = <&l4ls_gclk>;
 	clock-names = "fck";
 };
diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
index e9a156b..41a2bd4 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
@@ -11,8 +11,6 @@ Required properties:
 - reg: physical base address and size of the registers map.
 
 Optional properties:
-- ti,hwmods: Name of the hwmod associated to the EHRPWM:
-  "ehrpwm<x>", <x> being the 0-based instance number from the HW spec
 - clocks: Handle to the PWM's time-base and functional clock.
 - clock-names: Must be set to "tbclk" and "fck".
 
@@ -24,7 +22,6 @@ ehrpwm0: pwm@48300200 { /* EHRPWM on am33xx */
 	reg = <0x48300200 0x100>;
 	clocks = <&ehrpwm0_tbclk>, <&l4ls_gclk>;
 	clock-names = "tbclk", "fck";
-	ti,hwmods = "ehrpwm0";
 };
 
 ehrpwm0: pwm@48300200 { /* EHRPWM on am4372 */
diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index 999ba2f..2661acc 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -687,7 +687,6 @@
 				clock-names = "fck";
 				interrupts = <31>;
 				interrupt-names = "ecap0";
-				ti,hwmods = "ecap0";
 				status = "disabled";
 			};
 
@@ -696,7 +695,6 @@
 					     "ti,am33xx-ehrpwm";
 				#pwm-cells = <3>;
 				reg = <0x48300200 0x80>;
-				ti,hwmods = "ehrpwm0";
 				clocks = <&ehrpwm0_tbclk>, <&l4ls_gclk>;
 				clock-names = "tbclk", "fck";
 				status = "disabled";
@@ -723,7 +721,6 @@
 				clock-names = "fck";
 				interrupts = <47>;
 				interrupt-names = "ecap1";
-				ti,hwmods = "ecap1";
 				status = "disabled";
 			};
 
@@ -732,7 +729,6 @@
 					     "ti,am33xx-ehrpwm";
 				#pwm-cells = <3>;
 				reg = <0x48302200 0x80>;
-				ti,hwmods = "ehrpwm1";
 				clocks = <&ehrpwm1_tbclk>, <&l4ls_gclk>;
 				clock-names = "tbclk", "fck";
 				status = "disabled";
@@ -759,7 +755,6 @@
 				clock-names = "fck";
 				interrupts = <61>;
 				interrupt-names = "ecap2";
-				ti,hwmods = "ecap2";
 				status = "disabled";
 			};
 
@@ -768,7 +763,6 @@
 					     "ti,am33xx-ehrpwm";
 				#pwm-cells = <3>;
 				reg = <0x48304200 0x80>;
-				ti,hwmods = "ehrpwm2";
 				clocks = <&ehrpwm2_tbclk>, <&l4ls_gclk>;
 				clock-names = "tbclk", "fck";
 				status = "disabled";
diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
index e858460..cfdd4b7 100644
--- a/arch/arm/boot/dts/am4372.dtsi
+++ b/arch/arm/boot/dts/am4372.dtsi
@@ -677,7 +677,6 @@
 					     "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48300100 0x80>;
-				ti,hwmods = "ecap0";
 				clocks = <&l4ls_gclk>;
 				clock-names = "fck";
 				status = "disabled";
@@ -689,7 +688,6 @@
 					     "ti,am33xx-ehrpwm";
 				#pwm-cells = <3>;
 				reg = <0x48300200 0x80>;
-				ti,hwmods = "ehrpwm0";
 				clocks = <&ehrpwm0_tbclk>, <&l4ls_gclk>;
 				clock-names = "tbclk", "fck";
 				status = "disabled";
@@ -711,7 +709,6 @@
 					     "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48302100 0x80>;
-				ti,hwmods = "ecap1";
 				clocks = <&l4ls_gclk>;
 				clock-names = "fck";
 				status = "disabled";
@@ -723,7 +720,6 @@
 					     "ti,am33xx-ehrpwm";
 				#pwm-cells = <3>;
 				reg = <0x48302200 0x80>;
-				ti,hwmods = "ehrpwm1";
 				clocks = <&ehrpwm1_tbclk>, <&l4ls_gclk>;
 				clock-names = "tbclk", "fck";
 				status = "disabled";
@@ -747,7 +743,6 @@
 				reg = <0x48304100 0x80>;
 				clocks = <&l4ls_gclk>;
 				clock-names = "fck";
-				ti,hwmods = "ecap2";
 				status = "disabled";
 			};
 
@@ -757,7 +752,6 @@
 					     "ti,am33xx-ehrpwm";
 				#pwm-cells = <3>;
 				reg = <0x48304200 0x80>;
-				ti,hwmods = "ehrpwm2";
 				clocks = <&ehrpwm2_tbclk>, <&l4ls_gclk>;
 				clock-names = "tbclk", "fck";
 				status = "disabled";
@@ -779,7 +773,6 @@
 					     "ti,am33xx-ehrpwm";
 				#pwm-cells = <3>;
 				reg = <0x48306200 0x80>;
-				ti,hwmods = "ehrpwm3";
 				clocks = <&ehrpwm3_tbclk>, <&l4ls_gclk>;
 				clock-names = "tbclk", "fck";
 				status = "disabled";
@@ -801,7 +794,6 @@
 					     "ti,am33xx-ehrpwm";
 				#pwm-cells = <3>;
 				reg = <0x48308200 0x80>;
-				ti,hwmods = "ehrpwm4";
 				clocks = <&ehrpwm4_tbclk>, <&l4ls_gclk>;
 				clock-names = "tbclk", "fck";
 				status = "disabled";
@@ -825,7 +817,6 @@
 				reg = <0x4830a200 0x80>;
 				clocks = <&ehrpwm5_tbclk>, <&l4ls_gclk>;
 				clock-names = "tbclk", "fck";
-				ti,hwmods = "ehrpwm5";
 				status = "disabled";
 			};
 		};
-- 
2.7.0

[PATCH v8 8/9] ARM: AM335x/AM437x: hwmod: Remove eQEP, ePWM and eCAP hwmod entries

[Franklin S Cooper Jr]

Devices that utilize the OCP registers and/or PRCM registers and
register bit fields should be modeled using hwmod. Since eQEP, ePWM and
eCAP don't fall under this category, remove their hwmod entries.

Instead these clocks simply use the clock that is passed through by its
parent PWMSS. Therefore, PWMSS handles the clock for itself and its
subdevices.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
---
 .../mach-omap2/omap_hwmod_33xx_43xx_common_data.h  | 18 -----
 .../omap_hwmod_33xx_43xx_interconnect_data.c       | 64 -----------------
 .../mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c | 84 ----------------------
 arch/arm/mach-omap2/omap_hwmod_33xx_data.c         |  9 ---
 arch/arm/mach-omap2/omap_hwmod_43xx_data.c         | 54 --------------
 5 files changed, 229 deletions(-)

diff --git a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_common_data.h b/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_common_data.h
index 7f73796..d3e61d1 100644
--- a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_common_data.h
+++ b/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_common_data.h
@@ -36,17 +36,8 @@ extern struct omap_hwmod_ocp_if am33xx_l4_per__gpio3;
 extern struct omap_hwmod_ocp_if am33xx_cpgmac0__mdio;
 extern struct omap_hwmod_ocp_if am33xx_l4_ls__elm;
 extern struct omap_hwmod_ocp_if am33xx_l4_ls__epwmss0;
-extern struct omap_hwmod_ocp_if am33xx_epwmss0__ecap0;
-extern struct omap_hwmod_ocp_if am33xx_epwmss0__eqep0;
-extern struct omap_hwmod_ocp_if am33xx_epwmss0__ehrpwm0;
 extern struct omap_hwmod_ocp_if am33xx_l4_ls__epwmss1;
-extern struct omap_hwmod_ocp_if am33xx_epwmss1__ecap1;
-extern struct omap_hwmod_ocp_if am33xx_epwmss1__eqep1;
-extern struct omap_hwmod_ocp_if am33xx_epwmss1__ehrpwm1;
 extern struct omap_hwmod_ocp_if am33xx_l4_ls__epwmss2;
-extern struct omap_hwmod_ocp_if am33xx_epwmss2__ecap2;
-extern struct omap_hwmod_ocp_if am33xx_epwmss2__eqep2;
-extern struct omap_hwmod_ocp_if am33xx_epwmss2__ehrpwm2;
 extern struct omap_hwmod_ocp_if am33xx_l3_s__gpmc;
 extern struct omap_hwmod_ocp_if am33xx_l4_per__i2c2;
 extern struct omap_hwmod_ocp_if am33xx_l4_per__i2c3;
@@ -98,17 +89,8 @@ extern struct omap_hwmod am33xx_dcan0_hwmod;
 extern struct omap_hwmod am33xx_dcan1_hwmod;
 extern struct omap_hwmod am33xx_elm_hwmod;
 extern struct omap_hwmod am33xx_epwmss0_hwmod;
-extern struct omap_hwmod am33xx_ecap0_hwmod;
-extern struct omap_hwmod am33xx_eqep0_hwmod;
-extern struct omap_hwmod am33xx_ehrpwm0_hwmod;
 extern struct omap_hwmod am33xx_epwmss1_hwmod;
-extern struct omap_hwmod am33xx_ecap1_hwmod;
-extern struct omap_hwmod am33xx_eqep1_hwmod;
-extern struct omap_hwmod am33xx_ehrpwm1_hwmod;
 extern struct omap_hwmod am33xx_epwmss2_hwmod;
-extern struct omap_hwmod am33xx_ecap2_hwmod;
-extern struct omap_hwmod am33xx_eqep2_hwmod;
-extern struct omap_hwmod am33xx_ehrpwm2_hwmod;
 extern struct omap_hwmod am33xx_gpio1_hwmod;
 extern struct omap_hwmod am33xx_gpio2_hwmod;
 extern struct omap_hwmod am33xx_gpio3_hwmod;
diff --git a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_interconnect_data.c b/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_interconnect_data.c
index 1c210cb..10dff2f 100644
--- a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_interconnect_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_interconnect_data.c
@@ -176,28 +176,6 @@ struct omap_hwmod_ocp_if am33xx_l4_ls__epwmss0 = {
 	.user		= OCP_USER_MPU,
 };
 
-struct omap_hwmod_ocp_if am33xx_epwmss0__ecap0 = {
-	.master		= &am33xx_epwmss0_hwmod,
-	.slave		= &am33xx_ecap0_hwmod,
-	.clk		= "l4ls_gclk",
-	.user		= OCP_USER_MPU,
-};
-
-struct omap_hwmod_ocp_if am33xx_epwmss0__eqep0 = {
-	.master		= &am33xx_epwmss0_hwmod,
-	.slave		= &am33xx_eqep0_hwmod,
-	.clk		= "l4ls_gclk",
-	.user		= OCP_USER_MPU,
-};
-
-struct omap_hwmod_ocp_if am33xx_epwmss0__ehrpwm0 = {
-	.master		= &am33xx_epwmss0_hwmod,
-	.slave		= &am33xx_ehrpwm0_hwmod,
-	.clk		= "l4ls_gclk",
-	.user		= OCP_USER_MPU,
-};
-
-
 static struct omap_hwmod_addr_space am33xx_epwmss1_addr_space[] = {
 	{
 		.pa_start	= 0x48302000,
@@ -215,27 +193,6 @@ struct omap_hwmod_ocp_if am33xx_l4_ls__epwmss1 = {
 	.user		= OCP_USER_MPU,
 };
 
-struct omap_hwmod_ocp_if am33xx_epwmss1__ecap1 = {
-	.master		= &am33xx_epwmss1_hwmod,
-	.slave		= &am33xx_ecap1_hwmod,
-	.clk		= "l4ls_gclk",
-	.user		= OCP_USER_MPU,
-};
-
-struct omap_hwmod_ocp_if am33xx_epwmss1__eqep1 = {
-	.master		= &am33xx_epwmss1_hwmod,
-	.slave		= &am33xx_eqep1_hwmod,
-	.clk		= "l4ls_gclk",
-	.user		= OCP_USER_MPU,
-};
-
-struct omap_hwmod_ocp_if am33xx_epwmss1__ehrpwm1 = {
-	.master		= &am33xx_epwmss1_hwmod,
-	.slave		= &am33xx_ehrpwm1_hwmod,
-	.clk		= "l4ls_gclk",
-	.user		= OCP_USER_MPU,
-};
-
 static struct omap_hwmod_addr_space am33xx_epwmss2_addr_space[] = {
 	{
 		.pa_start	= 0x48304000,
@@ -253,27 +210,6 @@ struct omap_hwmod_ocp_if am33xx_l4_ls__epwmss2 = {
 	.user		= OCP_USER_MPU,
 };
 
-struct omap_hwmod_ocp_if am33xx_epwmss2__ecap2 = {
-	.master		= &am33xx_epwmss2_hwmod,
-	.slave		= &am33xx_ecap2_hwmod,
-	.clk		= "l4ls_gclk",
-	.user		= OCP_USER_MPU,
-};
-
-struct omap_hwmod_ocp_if am33xx_epwmss2__eqep2 = {
-	.master		= &am33xx_epwmss2_hwmod,
-	.slave		= &am33xx_eqep2_hwmod,
-	.clk		= "l4ls_gclk",
-	.user		= OCP_USER_MPU,
-};
-
-struct omap_hwmod_ocp_if am33xx_epwmss2__ehrpwm2 = {
-	.master		= &am33xx_epwmss2_hwmod,
-	.slave		= &am33xx_ehrpwm2_hwmod,
-	.clk		= "l4ls_gclk",
-	.user		= OCP_USER_MPU,
-};
-
 /* l3s cfg -> gpmc */
 struct omap_hwmod_ocp_if am33xx_l3_s__gpmc = {
 	.master		= &am33xx_l3_s_hwmod,
diff --git a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c b/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c
index aed3362..6a73b6c 100644
--- a/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c
@@ -449,18 +449,6 @@ struct omap_hwmod_class am33xx_epwmss_hwmod_class = {
 	.sysc		= &am33xx_epwmss_sysc,
 };
 
-static struct omap_hwmod_class am33xx_ecap_hwmod_class = {
-	.name		= "ecap",
-};
-
-static struct omap_hwmod_class am33xx_eqep_hwmod_class = {
-	.name		= "eqep",
-};
-
-struct omap_hwmod_class am33xx_ehrpwm_hwmod_class = {
-	.name		= "ehrpwm",
-};
-
 /* epwmss0 */
 struct omap_hwmod am33xx_epwmss0_hwmod = {
 	.name		= "epwmss0",
@@ -474,30 +462,6 @@ struct omap_hwmod am33xx_epwmss0_hwmod = {
 	},
 };
 
-/* ecap0 */
-struct omap_hwmod am33xx_ecap0_hwmod = {
-	.name		= "ecap0",
-	.class		= &am33xx_ecap_hwmod_class,
-	.clkdm_name	= "l4ls_clkdm",
-	.main_clk	= "l4ls_gclk",
-};
-
-/* eqep0 */
-struct omap_hwmod am33xx_eqep0_hwmod = {
-	.name		= "eqep0",
-	.class		= &am33xx_eqep_hwmod_class,
-	.clkdm_name	= "l4ls_clkdm",
-	.main_clk	= "l4ls_gclk",
-};
-
-/* ehrpwm0 */
-struct omap_hwmod am33xx_ehrpwm0_hwmod = {
-	.name		= "ehrpwm0",
-	.class		= &am33xx_ehrpwm_hwmod_class,
-	.clkdm_name	= "l4ls_clkdm",
-	.main_clk	= "l4ls_gclk",
-};
-
 /* epwmss1 */
 struct omap_hwmod am33xx_epwmss1_hwmod = {
 	.name		= "epwmss1",
@@ -511,30 +475,6 @@ struct omap_hwmod am33xx_epwmss1_hwmod = {
 	},
 };
 
-/* ecap1 */
-struct omap_hwmod am33xx_ecap1_hwmod = {
-	.name		= "ecap1",
-	.class		= &am33xx_ecap_hwmod_class,
-	.clkdm_name	= "l4ls_clkdm",
-	.main_clk	= "l4ls_gclk",
-};
-
-/* eqep1 */
-struct omap_hwmod am33xx_eqep1_hwmod = {
-	.name		= "eqep1",
-	.class		= &am33xx_eqep_hwmod_class,
-	.clkdm_name	= "l4ls_clkdm",
-	.main_clk	= "l4ls_gclk",
-};
-
-/* ehrpwm1 */
-struct omap_hwmod am33xx_ehrpwm1_hwmod = {
-	.name		= "ehrpwm1",
-	.class		= &am33xx_ehrpwm_hwmod_class,
-	.clkdm_name	= "l4ls_clkdm",
-	.main_clk	= "l4ls_gclk",
-};
-
 /* epwmss2 */
 struct omap_hwmod am33xx_epwmss2_hwmod = {
 	.name		= "epwmss2",
@@ -548,30 +488,6 @@ struct omap_hwmod am33xx_epwmss2_hwmod = {
 	},
 };
 
-/* ecap2 */
-struct omap_hwmod am33xx_ecap2_hwmod = {
-	.name		= "ecap2",
-	.class		= &am33xx_ecap_hwmod_class,
-	.clkdm_name	= "l4ls_clkdm",
-	.main_clk	= "l4ls_gclk",
-};
-
-/* eqep2 */
-struct omap_hwmod am33xx_eqep2_hwmod = {
-	.name		= "eqep2",
-	.class		= &am33xx_eqep_hwmod_class,
-	.clkdm_name	= "l4ls_clkdm",
-	.main_clk	= "l4ls_gclk",
-};
-
-/* ehrpwm2 */
-struct omap_hwmod am33xx_ehrpwm2_hwmod = {
-	.name		= "ehrpwm2",
-	.class		= &am33xx_ehrpwm_hwmod_class,
-	.clkdm_name	= "l4ls_clkdm",
-	.main_clk	= "l4ls_gclk",
-};
-
 /*
  * 'gpio' class: for gpio 0,1,2,3
  */
diff --git a/arch/arm/mach-omap2/omap_hwmod_33xx_data.c b/arch/arm/mach-omap2/omap_hwmod_33xx_data.c
index cc0791d..e1c2025 100644
--- a/arch/arm/mach-omap2/omap_hwmod_33xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_33xx_data.c
@@ -593,17 +593,8 @@ static struct omap_hwmod_ocp_if *am33xx_hwmod_ocp_ifs[] __initdata = {
 	&am33xx_l4_ls__spinlock,
 	&am33xx_l4_ls__elm,
 	&am33xx_l4_ls__epwmss0,
-	&am33xx_epwmss0__ecap0,
-	&am33xx_epwmss0__eqep0,
-	&am33xx_epwmss0__ehrpwm0,
 	&am33xx_l4_ls__epwmss1,
-	&am33xx_epwmss1__ecap1,
-	&am33xx_epwmss1__eqep1,
-	&am33xx_epwmss1__ehrpwm1,
 	&am33xx_l4_ls__epwmss2,
-	&am33xx_epwmss2__ecap2,
-	&am33xx_epwmss2__eqep2,
-	&am33xx_epwmss2__ehrpwm2,
 	&am33xx_l3_s__gpmc,
 	&am33xx_l3_main__lcdc,
 	&am33xx_l4_ls__mcspi0,
diff --git a/arch/arm/mach-omap2/omap_hwmod_43xx_data.c b/arch/arm/mach-omap2/omap_hwmod_43xx_data.c
index 97fd399..61f2f30 100644
--- a/arch/arm/mach-omap2/omap_hwmod_43xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_43xx_data.c
@@ -202,13 +202,6 @@ static struct omap_hwmod am43xx_epwmss3_hwmod = {
 	},
 };
 
-static struct omap_hwmod am43xx_ehrpwm3_hwmod = {
-	.name		= "ehrpwm3",
-	.class		= &am33xx_ehrpwm_hwmod_class,
-	.clkdm_name	= "l4ls_clkdm",
-	.main_clk	= "l4ls_gclk",
-};
-
 static struct omap_hwmod am43xx_epwmss4_hwmod = {
 	.name		= "epwmss4",
 	.class		= &am33xx_epwmss_hwmod_class,
@@ -222,13 +215,6 @@ static struct omap_hwmod am43xx_epwmss4_hwmod = {
 	},
 };
 
-static struct omap_hwmod am43xx_ehrpwm4_hwmod = {
-	.name		= "ehrpwm4",
-	.class		= &am33xx_ehrpwm_hwmod_class,
-	.clkdm_name	= "l4ls_clkdm",
-	.main_clk	= "l4ls_gclk",
-};
-
 static struct omap_hwmod am43xx_epwmss5_hwmod = {
 	.name		= "epwmss5",
 	.class		= &am33xx_epwmss_hwmod_class,
@@ -242,13 +228,6 @@ static struct omap_hwmod am43xx_epwmss5_hwmod = {
 	},
 };
 
-static struct omap_hwmod am43xx_ehrpwm5_hwmod = {
-	.name		= "ehrpwm5",
-	.class		= &am33xx_ehrpwm_hwmod_class,
-	.clkdm_name	= "l4ls_clkdm",
-	.main_clk	= "l4ls_gclk",
-};
-
 static struct omap_hwmod am43xx_spi2_hwmod = {
 	.name		= "spi2",
 	.class		= &am33xx_spi_hwmod_class,
@@ -744,13 +723,6 @@ static struct omap_hwmod_ocp_if am43xx_l4_ls__epwmss3 = {
 	.user		= OCP_USER_MPU,
 };
 
-static struct omap_hwmod_ocp_if am43xx_epwmss3__ehrpwm3 = {
-	.master		= &am43xx_epwmss3_hwmod,
-	.slave		= &am43xx_ehrpwm3_hwmod,
-	.clk		= "l4ls_gclk",
-	.user		= OCP_USER_MPU,
-};
-
 static struct omap_hwmod_ocp_if am43xx_l4_ls__epwmss4 = {
 	.master		= &am33xx_l4_ls_hwmod,
 	.slave		= &am43xx_epwmss4_hwmod,
@@ -758,13 +730,6 @@ static struct omap_hwmod_ocp_if am43xx_l4_ls__epwmss4 = {
 	.user		= OCP_USER_MPU,
 };
 
-static struct omap_hwmod_ocp_if am43xx_epwmss4__ehrpwm4 = {
-	.master		= &am43xx_epwmss4_hwmod,
-	.slave		= &am43xx_ehrpwm4_hwmod,
-	.clk		= "l4ls_gclk",
-	.user		= OCP_USER_MPU,
-};
-
 static struct omap_hwmod_ocp_if am43xx_l4_ls__epwmss5 = {
 	.master		= &am33xx_l4_ls_hwmod,
 	.slave		= &am43xx_epwmss5_hwmod,
@@ -772,13 +737,6 @@ static struct omap_hwmod_ocp_if am43xx_l4_ls__epwmss5 = {
 	.user		= OCP_USER_MPU,
 };
 
-static struct omap_hwmod_ocp_if am43xx_epwmss5__ehrpwm5 = {
-	.master		= &am43xx_epwmss5_hwmod,
-	.slave		= &am43xx_ehrpwm5_hwmod,
-	.clk		= "l4ls_gclk",
-	.user		= OCP_USER_MPU,
-};
-
 static struct omap_hwmod_ocp_if am43xx_l4_ls__mcspi2 = {
 	.master		= &am33xx_l4_ls_hwmod,
 	.slave		= &am43xx_spi2_hwmod,
@@ -919,11 +877,8 @@ static struct omap_hwmod_ocp_if *am43xx_hwmod_ocp_ifs[] __initdata = {
 	&am43xx_l4_ls__timer10,
 	&am43xx_l4_ls__timer11,
 	&am43xx_l4_ls__epwmss3,
-	&am43xx_epwmss3__ehrpwm3,
 	&am43xx_l4_ls__epwmss4,
-	&am43xx_epwmss4__ehrpwm4,
 	&am43xx_l4_ls__epwmss5,
-	&am43xx_epwmss5__ehrpwm5,
 	&am43xx_l4_ls__mcspi2,
 	&am43xx_l4_ls__mcspi3,
 	&am43xx_l4_ls__mcspi4,
@@ -982,17 +937,8 @@ static struct omap_hwmod_ocp_if *am43xx_hwmod_ocp_ifs[] __initdata = {
 	&am33xx_l4_ls__spinlock,
 	&am33xx_l4_ls__elm,
 	&am33xx_l4_ls__epwmss0,
-	&am33xx_epwmss0__ecap0,
-	&am33xx_epwmss0__eqep0,
-	&am33xx_epwmss0__ehrpwm0,
 	&am33xx_l4_ls__epwmss1,
-	&am33xx_epwmss1__ecap1,
-	&am33xx_epwmss1__eqep1,
-	&am33xx_epwmss1__ehrpwm1,
 	&am33xx_l4_ls__epwmss2,
-	&am33xx_epwmss2__ecap2,
-	&am33xx_epwmss2__eqep2,
-	&am33xx_epwmss2__ehrpwm2,
 	&am33xx_l3_s__gpmc,
 	&am33xx_l4_ls__mcspi0,
 	&am33xx_l4_ls__mcspi1,
-- 
2.7.0

[PATCH v8 9/9] ARM: dts: DRA7: Add dt nodes for PWMSS

[Franklin S Cooper Jr]

From: Vignesh R <vigneshr@ti.com>

Add PWMSS device tree nodes for DRA7 SoC family and add documentation
for dt bindings.

Signed-off-by: Vignesh R <vigneshr@ti.com>
[fcooper@ti.com: Add eCAP and use updated bindings for PWMSS and ePWM]
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 .../devicetree/bindings/pwm/pwm-tiecap.txt         |  9 +++
 .../devicetree/bindings/pwm/pwm-tiehrpwm.txt       |  9 +++
 .../devicetree/bindings/pwm/pwm-tipwmss.txt        | 12 +++
 arch/arm/boot/dts/dra7.dtsi                        | 90 ++++++++++++++++++++++
 4 files changed, 120 insertions(+)

diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
index f2a9a7c..8007e83 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
@@ -5,6 +5,7 @@ Required properties:
   for am33xx - compatible = "ti,am3352-ecap", "ti,am33xx-ecap";
   for am4372 - compatible = "ti,am4372-ecap", "ti,am3352-ecap", "ti,am33xx-ecap";
   for da850  - compatible = "ti,da850-ecap", "ti,am3352-ecap", "ti,am33xx-ecap";
+  for dra746 - compatible = "ti,dra746-ecap", "ti,am3352-ecap";
 - #pwm-cells: should be 3. See pwm.txt in this directory for a description of
   the cells format. The PWM channel index ranges from 0 to 4. The only third
   cell flag supported by this binding is PWM_POLARITY_INVERTED.
@@ -38,3 +39,11 @@ ecap0: ecap@1f06000 { /* ECAP on da850 */
 	#pwm-cells = <3>;
 	reg = <0x1f06000 0x80>;
 };
+
+ecap0: ecap@4843e100 {
+	compatible = "ti,dra746-ecap", "ti,am3352-ecap";
+	#pwm-cells = <3>;
+	reg = <0x4843e100 0x80>;
+	clocks = <&l4_root_clk_div>;
+	clock-names = "fck";
+};
diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
index 41a2bd4..944fe35 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
@@ -5,6 +5,7 @@ Required properties:
   for am33xx  - compatible = "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm";
   for am4372  - compatible = "ti,am4372-ehrpwm", "ti-am3352-ehrpwm", "ti,am33xx-ehrpwm";
   for da850   - compatible = "ti,da850-ehrpwm", "ti-am3352-ehrpwm", "ti,am33xx-ehrpwm";
+  for dra746 - compatible = "ti,dra746-ehrpwm", "ti-am3352-ehrpwm";
 - #pwm-cells: should be 3. See pwm.txt in this directory for a description of
   the cells format. The only third cell flag supported by this binding is
   PWM_POLARITY_INVERTED.
@@ -38,3 +39,11 @@ ehrpwm0: pwm@1f00000 { /* EHRPWM on da850 */
 	#pwm-cells = <3>;
 	reg = <0x1f00000 0x2000>;
 };
+
+ehrpwm0: pwm@4843e200 { /* EHRPWM on dra746 */
+	compatible = "ti,dra746-ehrpwm", "ti,am3352-ehrpwm";
+	#pwm-cells = <3>;
+	reg = <0x4843e200 0x80>;
+	clocks = <&ehrpwm0_tbclk>, <&l4_root_clk_div>;
+	clock-names = "tbclk", "fck";
+};
diff --git a/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt
index fd8e87c..1a5d7b7 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt
@@ -4,6 +4,7 @@ Required properties:
 - compatible: Must be "ti,<soc>-pwmss".
   for am33xx  - compatible = "ti,am33xx-pwmss";
   for am4372  - compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
+  for dra746 - compatible = "ti,dra746-pwmss", "ti,am33xx-pwmss"
 
 - reg: physical base address and size of the registers map.
 - address-cells: Specify the number of u32 entries needed in child nodes.
@@ -46,3 +47,14 @@ epwmss0: epwmss@48300000 { /* PWMSS for am4372 */
 
 	/* child nodes go here */
 };
+
+epwmss0: epwmss@4843e000 { /* PWMSS for DRA7xx */
+	compatible = "ti,dra746-pwmss", "ti,am33xx-pwmss";
+	reg = <0x4843e000 0x30>;
+	ti,hwmods = "epwmss0";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+
+	/* child nodes go here */
+};
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index e007401..5a21e46 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -1743,6 +1743,96 @@
 				clock-names = "fck", "sys_clk";
 			};
 		};
+
+		epwmss0: epwmss@4843e000 {
+			compatible = "ti,dra746-pwmss", "ti,am33xx-pwmss";
+			reg = <0x4843e000 0x30>;
+			ti,hwmods = "epwmss0";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+			ranges;
+
+			ehrpwm0: pwm@4843e200 {
+				compatible = "ti,dra746-ehrpwm",
+					     "ti,am3352-ehrpwm";
+				#pwm-cells = <3>;
+				reg = <0x4843e200 0x80>;
+				clocks = <&ehrpwm0_tbclk>, <&l4_root_clk_div>;
+				clock-names = "tbclk", "fck";
+				status = "disabled";
+			};
+
+			ecap0: ecap@4843e100 {
+				compatible = "ti,dra746-ecap",
+					     "ti,am3352-ecap";
+				#pwm-cells = <3>;
+				reg = <0x4843e100 0x80>;
+				clocks = <&l4_root_clk_div>;
+				clock-names = "fck";
+				status = "disabled";
+			};
+		};
+
+		epwmss1: epwmss@48440000 {
+			compatible = "ti,dra746-pwmss", "ti,am33xx-pwmss";
+			reg = <0x48440000 0x30>;
+			ti,hwmods = "epwmss1";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+			ranges;
+
+			ehrpwm1: pwm@48440200 {
+				compatible = "ti,dra746-ehrpwm",
+					     "ti,am3352-ehrpwm";
+				#pwm-cells = <3>;
+				reg = <0x48440200 0x80>;
+				clocks = <&ehrpwm1_tbclk>, <&l4_root_clk_div>;
+				clock-names = "tbclk", "fck";
+				status = "disabled";
+			};
+
+			ecap1: ecap@48440100 {
+				compatible = "ti,dra746-ecap",
+					     "ti,am3352-ecap";
+				#pwm-cells = <3>;
+				reg = <0x48440100 0x80>;
+				clocks = <&l4_root_clk_div>;
+				clock-names = "fck";
+				status = "disabled";
+			};
+		};
+
+		epwmss2: epwmss@48442000 {
+			compatible = "ti,dra746-pwmss", "ti,am33xx-pwmss";
+			reg = <0x48442000 0x30>;
+			ti,hwmods = "epwmss2";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+			ranges;
+
+			ehrpwm2: pwm@48442200 {
+				compatible = "ti,dra746-ehrpwm",
+					     "ti,am3352-ehrpwm";
+				#pwm-cells = <3>;
+				reg = <0x48442200 0x80>;
+				clocks = <&ehrpwm2_tbclk>, <&l4_root_clk_div>;
+				clock-names = "tbclk", "fck";
+				status = "disabled";
+			};
+
+			ecap2: ecap@48442100 {
+				compatible = "ti,dra746-ecap",
+					     "ti,am3352-ecap";
+				#pwm-cells = <3>;
+				reg = <0x48442100 0x80>;
+				clocks = <&l4_root_clk_div>;
+				clock-names = "fck";
+				status = "disabled";
+			};
+		};
 	};
 
 	thermal_zones: thermal-zones {
-- 
2.7.0

Re: [PATCH v8 4/9] pwm: pwm-tiecap: Update dt binding document to use proper unit address

[Rob Herring]

On Tue, May 03, 2016 at 10:56:50AM -0500, Franklin S Cooper Jr wrote:
> Replace unit address from 0 to the proper physical address. Also insure
> that the unit address matches the reg property address.
> 
> Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
> ---
>  Documentation/devicetree/bindings/pwm/pwm-tiecap.txt | 8 ++++----
>  1 file changed, 4 insertions(+), 4 deletions(-)

Acked-by: Rob Herring <robh@kernel.org>

> 
> diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
> index 788da6c..0d47354 100644
> --- a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
> +++ b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
> @@ -16,22 +16,22 @@ Optional properties:
>  
>  Example:
>  
> -ecap0: ecap@0 { /* ECAP on am33xx */
> +ecap0: ecap@48300100 { /* ECAP on am33xx */
>  	compatible = "ti,am33xx-ecap";
>  	#pwm-cells = <3>;
>  	reg = <0x48300100 0x80>;
>  	ti,hwmods = "ecap0";
>  };
>  
> -ecap0: ecap@0 { /* ECAP on am4372 */
> +ecap0: ecap@48300100 { /* ECAP on am4372 */
>  	compatible = "ti,am4372-ecap", "ti,am33xx-ecap";
>  	#pwm-cells = <3>;
>  	reg = <0x48300100 0x80>;
>  	ti,hwmods = "ecap0";
>  };
>  
> -ecap0: ecap@0 { /* ECAP on da850 */
> +ecap0: ecap@1f06000 { /* ECAP on da850 */
>  	compatible = "ti,da850-ecap", "ti,am33xx-ecap";
>  	#pwm-cells = <3>;
> -	reg = <0x306000 0x80>;
> +	reg = <0x1f06000 0x80>;
>  };
> -- 
> 2.7.0
> 

Re: [PATCH v8 0/9] ARM: dts: DRA7: Add dt nodes for PWMSS

[Franklin Cooper Jr.]

Gentle ping on this series

On 05/03/2016 10:56 AM, Franklin S Cooper Jr wrote:
> This patch series adds support for PWM for DRA7. The IP is the same as the
> one present in AM33XX and AM437XX.
>
> However, before doing so remove unnecessary hwmod entries for eCAP, ePWM
> and eQEP.
>
> The following are the biggest changes from v7 to v8:
> Insure DT unit address matches reg property address
>
> The following are the biggest changes from v6 to v7:
> * Several patches to document previously undocumented bindings.
> * Fix minor issues in binding documents.
>
> The following are the biggest changes from v5 to v6:
> * Created two new bindings to allow ECAP and PWM to grab their functional
> clock from DT rather than depending on PWMSS parent.
> * Pull in a couple of patches from the "Correct PWM bindings" series. This
> makes it a bit easier to understand.
>
> From the two patchsets a handful of patches have already been pulled in by
> maintainers and have already made it to linux-next. Therefore, this
> patch series is built ontop of the latest linux-next.
>
> Tested on:
> AM335x, AM437x and X15 + lcd w/backlight
>
> Franklin S Cooper Jr (8):
>   clk: ti: am335x/am4372: Add tbclk to pwm node
>   ARM: dts: am437x: Add missing compatibles to PWM binding documents
>   pwm: pwm-tiehrpwm: Update dt binding document to use generic node name
>   pwm: pwm-tiecap: Update dt binding document to use proper unit address
>   ARM: dts: am437x/am33xx/da850: Add new ECAP and EPWM bindings
>   pwms: pwm-ti*: Get the clock from the PWMSS parent when using old
>     bindings
>   ARM: dts: am437x/am33xx: Remove hwmod entries for ECAP and EPWM nodes
>   ARM: AM335x/AM437x: hwmod: Remove eQEP, ePWM and eCAP hwmod entries
>
> Vignesh R (1):
>   ARM: dts: DRA7: Add dt nodes for PWMSS
>
>  .../devicetree/bindings/pwm/pwm-tiecap.txt         | 38 ++++++---
>  .../devicetree/bindings/pwm/pwm-tiehrpwm.txt       | 38 ++++++---
>  .../devicetree/bindings/pwm/pwm-tipwmss.txt        | 33 +++++++-
>  arch/arm/boot/dts/am33xx.dtsi                      | 36 ++++++---
>  arch/arm/boot/dts/am4372.dtsi                      | 63 ++++++++++-----
>  arch/arm/boot/dts/da850.dtsi                       | 15 ++--
>  arch/arm/boot/dts/dra7.dtsi                        | 90 ++++++++++++++++++++++
>  .../mach-omap2/omap_hwmod_33xx_43xx_common_data.h  | 18 -----
>  .../omap_hwmod_33xx_43xx_interconnect_data.c       | 64 ---------------
>  .../mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c | 84 --------------------
>  arch/arm/mach-omap2/omap_hwmod_33xx_data.c         |  9 ---
>  arch/arm/mach-omap2/omap_hwmod_43xx_data.c         | 54 -------------
>  drivers/clk/ti/clk-33xx.c                          |  3 +
>  drivers/clk/ti/clk-43xx.c                          |  6 ++
>  drivers/pwm/pwm-tiecap.c                           |  7 ++
>  drivers/pwm/pwm-tiehrpwm.c                         |  7 ++
>  16 files changed, 281 insertions(+), 284 deletions(-)
>

Re: [PATCH v8 5/9] ARM: dts: am437x/am33xx/da850: Add new ECAP and EPWM bindings

[Tony Lindgren]

* Franklin S Cooper Jr <fcooper@ti.com> [160503 08:58]:
> Switch to a new ECAP and EPWM bindings that doesn't depend on hwmod to
> provide the various required clocks.
> 
> For AM437 and AM335x, add the required clocks explicitly to DT. The
> hwmod entries for ECAP and EPWM will be removed and this will prevent
> anything from breaking.

I've applying the first patch into omap-for-v4.8/soc, the rest into
omap-for-v4.8/dt. Note that this patch did not apply against d850.dtsi
so please resend that change as a separate patch to the davinci
maintainer.

Regards,

Tony

Re: [PATCH v8 5/9] ARM: dts: am437x/am33xx/da850: Add new ECAP and EPWM bindings

[Tony Lindgren]

* Tony Lindgren <tony@atomide.com> [160610 03:37]:
> * Franklin S Cooper Jr <fcooper@ti.com> [160503 08:58]:
> > Switch to a new ECAP and EPWM bindings that doesn't depend on hwmod to
> > provide the various required clocks.
> > 
> > For AM437 and AM335x, add the required clocks explicitly to DT. The
> > hwmod entries for ECAP and EPWM will be removed and this will prevent
> > anything from breaking.
> 
> I've applying the first patch into omap-for-v4.8/soc, the rest into
> omap-for-v4.8/dt. Note that this patch did not apply against d850.dtsi
> so please resend that change as a separate patch to the davinci
> maintainer.

And I did not apply patch "pwms: pwm-ti*: Get the clock from the PWMSS
parent when using old bindings", Thierry should take that one.

Regards,

Tony

Re: [PATCH v8 8/9] ARM: AM335x/AM437x: hwmod: Remove eQEP, ePWM and eCAP hwmod entries

[Tony Lindgren]

* Franklin S Cooper Jr <fcooper@ti.com> [160503 08:58]:
> Devices that utilize the OCP registers and/or PRCM registers and
> register bit fields should be modeled using hwmod. Since eQEP, ePWM and
> eCAP don't fall under this category, remove their hwmod entries.
> 
> Instead these clocks simply use the clock that is passed through by its
> parent PWMSS. Therefore, PWMSS handles the clock for itself and its
> subdevices.
> 
> Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
> Acked-by: Paul Walmsley <paul@pwsan.com>

And this one I'm applying into omap-for-v4.8/soc.

Tony

Re: [PATCH v8 5/9] ARM: dts: am437x/am33xx/da850: Add new ECAP and EPWM bindings

[Thierry Reding]

[-- Attachment #1: Type: text/plain, Size: 1018 bytes --]

On Fri, Jun 10, 2016 at 05:01:43AM -0700, Tony Lindgren wrote:
> * Tony Lindgren <tony@atomide.com> [160610 03:37]:
> > * Franklin S Cooper Jr <fcooper@ti.com> [160503 08:58]:
> > > Switch to a new ECAP and EPWM bindings that doesn't depend on hwmod to
> > > provide the various required clocks.
> > > 
> > > For AM437 and AM335x, add the required clocks explicitly to DT. The
> > > hwmod entries for ECAP and EPWM will be removed and this will prevent
> > > anything from breaking.
> > 
> > I've applying the first patch into omap-for-v4.8/soc, the rest into
> > omap-for-v4.8/dt. Note that this patch did not apply against d850.dtsi
> > so please resend that change as a separate patch to the davinci
> > maintainer.
> 
> And I did not apply patch "pwms: pwm-ti*: Get the clock from the PWMSS
> parent when using old bindings", Thierry should take that one.

Tony, did you take patches 3 and 4 already? It's fine if yo have, just
wanted to know whether I should pick those up as well.

Thierry

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v8 6/9] pwms: pwm-ti*: Get the clock from the PWMSS parent when using old bindings

[Thierry Reding]

[-- Attachment #1: Type: text/plain, Size: 2463 bytes --]

On Tue, May 03, 2016 at 10:56:52AM -0500, Franklin S Cooper Jr wrote:
> When using the old eCAP and ePWM bindings for AM335x and AM437x the clock
> can be retrieved from the PWMSS parent. Newer bindings will insure that
> this clock is provided via device tree.
> 
> Therefore, update this driver to support the newer and older bindings. In
> the case of the older binding being used give a warning.
> 
> Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
> ---
>  drivers/pwm/pwm-tiecap.c   | 7 +++++++
>  drivers/pwm/pwm-tiehrpwm.c | 7 +++++++
>  2 files changed, 14 insertions(+)
> 
> diff --git a/drivers/pwm/pwm-tiecap.c b/drivers/pwm/pwm-tiecap.c
> index 616af76..a0833c8 100644
> --- a/drivers/pwm/pwm-tiecap.c
> +++ b/drivers/pwm/pwm-tiecap.c
> @@ -195,6 +195,7 @@ static const struct pwm_ops ecap_pwm_ops = {
>  };
>  
>  static const struct of_device_id ecap_of_match[] = {
> +	{ .compatible	= "ti,am3352-ecap" },
>  	{ .compatible	= "ti,am33xx-ecap" },
>  	{},
>  };
> @@ -213,6 +214,12 @@ static int ecap_pwm_probe(struct platform_device *pdev)
>  		return -ENOMEM;
>  
>  	clk = devm_clk_get(&pdev->dev, "fck");
> +
> +	if (IS_ERR(clk) && of_device_is_compatible(pdev->dev.of_node, "ti,am33xx-ecap")) {
> +		dev_warn(&pdev->dev, "Binding is obsolete.\n");
> +		clk = devm_clk_get(pdev->dev.parent, "fck");
> +	}

I rewrote this slightly for readability:

	struct device_node *np = pdev->dev.of_node;

	if (IS_ERR(clk)) {
		if (of_device_is_compatible(np, "ti,am33xx-ecap")) {
			...
		}
	}

>  	if (IS_ERR(clk)) {
>  		dev_err(&pdev->dev, "failed to get clock\n");
>  		return PTR_ERR(clk);
> diff --git a/drivers/pwm/pwm-tiehrpwm.c b/drivers/pwm/pwm-tiehrpwm.c
> index 6a41e66..cee29a2 100644
> --- a/drivers/pwm/pwm-tiehrpwm.c
> +++ b/drivers/pwm/pwm-tiehrpwm.c
> @@ -426,6 +426,7 @@ static const struct pwm_ops ehrpwm_pwm_ops = {
>  };
>  
>  static const struct of_device_id ehrpwm_of_match[] = {
> +	{ .compatible	= "ti,am3352-ehrpwm" },
>  	{ .compatible	= "ti,am33xx-ehrpwm" },
>  	{},
>  };
> @@ -444,6 +445,12 @@ static int ehrpwm_pwm_probe(struct platform_device *pdev)
>  		return -ENOMEM;
>  
>  	clk = devm_clk_get(&pdev->dev, "fck");
> +
> +	if (IS_ERR(clk) && of_device_is_compatible(pdev->dev.of_node, "ti,am33xx-ecap")) {
> +		dev_warn(&pdev->dev, "Binding is obsolete.\n");
> +		clk = devm_clk_get(pdev->dev.parent, "fck");
> +	}
> +

Same here.

Thierry

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v8 5/9] ARM: dts: am437x/am33xx/da850: Add new ECAP and EPWM bindings

[Tony Lindgren]

* Thierry Reding <thierry.reding@gmail.com> [160610 05:42]:
> On Fri, Jun 10, 2016 at 05:01:43AM -0700, Tony Lindgren wrote:
> > * Tony Lindgren <tony@atomide.com> [160610 03:37]:
> > > * Franklin S Cooper Jr <fcooper@ti.com> [160503 08:58]:
> > > > Switch to a new ECAP and EPWM bindings that doesn't depend on hwmod=
 to
> > > > provide the various required clocks.
> > > >=20
> > > > For AM437 and AM335x, add the required clocks explicitly to DT. The
> > > > hwmod entries for ECAP and EPWM will be removed and this will preve=
nt
> > > > anything from breaking.
> > >=20
> > > I've applying the first patch into omap-for-v4.8/soc, the rest into
> > > omap-for-v4.8/dt. Note that this patch did not apply against d850.dtsi
> > > so please resend that change as a separate patch to the davinci
> > > maintainer.
> >=20
> > And I did not apply patch "pwms: pwm-ti*: Get the clock from the PWMSS
> > parent when using old bindings", Thierry should take that one.
>=20
> Tony, did you take patches 3 and 4 already? It's fine if yo have, just
> wanted to know whether I should pick those up as well.

Yes looks like I also took the binding documentation patches too.

Regards,

Tony

Re: [PATCH v8 3/9] pwm: pwm-tiehrpwm: Update dt binding document to use generic node name

[Thierry Reding]

[-- Attachment #1: Type: text/plain, Size: 662 bytes --]

On Tue, May 03, 2016 at 10:56:49AM -0500, Franklin S Cooper Jr wrote:
> Now that the node name has been changed from ehrpwm to pwm the document
> should show this proper usage. Change the unit address in the example
> from 0 to the proper physical address value that should be used. Also
> insure that the unit address matches to the reg property.
> 
> Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
> Acked-by: Rob Herring <robh@kernel.org>
> ---
>  Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt | 8 ++++----
>  1 file changed, 4 insertions(+), 4 deletions(-)

I applied this long ago, but never replied: Applied, thanks.

Thierry

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v8 4/9] pwm: pwm-tiecap: Update dt binding document to use proper unit address

[Thierry Reding]

[-- Attachment #1: Type: text/plain, Size: 473 bytes --]

On Tue, May 03, 2016 at 10:56:50AM -0500, Franklin S Cooper Jr wrote:
> Replace unit address from 0 to the proper physical address. Also insure
> that the unit address matches the reg property address.
> 
> Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
> ---
>  Documentation/devicetree/bindings/pwm/pwm-tiecap.txt | 8 ++++----
>  1 file changed, 4 insertions(+), 4 deletions(-)

I applied this long ago but never let you know: Applied, thanks.

Thierry

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v8 4/9] pwm: pwm-tiecap: Update dt binding document to use proper unit address

[Thierry Reding]

[-- Attachment #1: Type: text/plain, Size: 791 bytes --]

On Mon, Jul 11, 2016 at 11:56:23AM +0200, Thierry Reding wrote:
> On Tue, May 03, 2016 at 10:56:50AM -0500, Franklin S Cooper Jr wrote:
> > Replace unit address from 0 to the proper physical address. Also insure
> > that the unit address matches the reg property address.
> > 
> > Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
> > ---
> >  Documentation/devicetree/bindings/pwm/pwm-tiecap.txt | 8 ++++----
> >  1 file changed, 4 insertions(+), 4 deletions(-)
> 
> I applied this long ago but never let you know: Applied, thanks.

Actually I didn't. And it seems the reason is that it doesn't apply
cleanly. For some reason my tree doesn't have an entry for the ecap
example on am437x. Am I missing a patch? Can you resend whatever is
not in linux-next yet?

Thierry

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v8 4/9] pwm: pwm-tiecap: Update dt binding document to use proper unit address

[Thierry Reding]

[-- Attachment #1: Type: text/plain, Size: 1103 bytes --]

On Mon, Jul 11, 2016 at 12:06:29PM +0200, Thierry Reding wrote:
> On Mon, Jul 11, 2016 at 11:56:23AM +0200, Thierry Reding wrote:
> > On Tue, May 03, 2016 at 10:56:50AM -0500, Franklin S Cooper Jr wrote:
> > > Replace unit address from 0 to the proper physical address. Also insure
> > > that the unit address matches the reg property address.
> > > 
> > > Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
> > > ---
> > >  Documentation/devicetree/bindings/pwm/pwm-tiecap.txt | 8 ++++----
> > >  1 file changed, 4 insertions(+), 4 deletions(-)
> > 
> > I applied this long ago but never let you know: Applied, thanks.
> 
> Actually I didn't. And it seems the reason is that it doesn't apply
> cleanly. For some reason my tree doesn't have an entry for the ecap
> example on am437x. Am I missing a patch? Can you resend whatever is
> not in linux-next yet?

Oh, nevermind my blabbering, it took me too long to realize that this is
the series that Tony had picked up for the most part, and I hadn't
properly marked it done in patchwork.

I'll go get some coffee now.

Thierry

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v8 1/9] clk: ti: am335x/am4372: Add tbclk to pwm node

[Michael Turquette]

Quoting Franklin S Cooper Jr (2016-05-03 08:56:47)
> Add tblck to the pwm nodes. This insures that the ehrpwm driver has access

s/tblck/tbclk/

I see you have acks already. What tree should this patch go through?

Regards,
Mike

> to the time-based clk.
> =

> Do not remove similar entries for ehrpwm node. Later patches will switch
> from using ehrpwm node name to pwm. But to maintain ABI compatibility we
> shouldn't remove the old entries.
> =

> Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
> Acked-by: Stephen Boyd <sboyd@codeaurora.org>
> Acked-by: Tero Kristo <t-kristo@ti.com>
> ---
>  drivers/clk/ti/clk-33xx.c | 3 +++
>  drivers/clk/ti/clk-43xx.c | 6 ++++++
>  2 files changed, 9 insertions(+)
> =

> diff --git a/drivers/clk/ti/clk-33xx.c b/drivers/clk/ti/clk-33xx.c
> index ef2ec64..0e47d95 100644
> --- a/drivers/clk/ti/clk-33xx.c
> +++ b/drivers/clk/ti/clk-33xx.c
> @@ -108,6 +108,9 @@ static struct ti_dt_clk am33xx_clks[] =3D {
>         DT_CLK("48300200.ehrpwm", "tbclk", "ehrpwm0_tbclk"),
>         DT_CLK("48302200.ehrpwm", "tbclk", "ehrpwm1_tbclk"),
>         DT_CLK("48304200.ehrpwm", "tbclk", "ehrpwm2_tbclk"),
> +       DT_CLK("48300200.pwm", "tbclk", "ehrpwm0_tbclk"),
> +       DT_CLK("48302200.pwm", "tbclk", "ehrpwm1_tbclk"),
> +       DT_CLK("48304200.pwm", "tbclk", "ehrpwm2_tbclk"),
>         { .node_name =3D NULL },
>  };
>  =

> diff --git a/drivers/clk/ti/clk-43xx.c b/drivers/clk/ti/clk-43xx.c
> index 097fc90..7255aa8 100644
> --- a/drivers/clk/ti/clk-43xx.c
> +++ b/drivers/clk/ti/clk-43xx.c
> @@ -115,6 +115,12 @@ static struct ti_dt_clk am43xx_clks[] =3D {
>         DT_CLK("48306200.ehrpwm", "tbclk", "ehrpwm3_tbclk"),
>         DT_CLK("48308200.ehrpwm", "tbclk", "ehrpwm4_tbclk"),
>         DT_CLK("4830a200.ehrpwm", "tbclk", "ehrpwm5_tbclk"),
> +       DT_CLK("48300200.pwm", "tbclk", "ehrpwm0_tbclk"),
> +       DT_CLK("48302200.pwm", "tbclk", "ehrpwm1_tbclk"),
> +       DT_CLK("48304200.pwm", "tbclk", "ehrpwm2_tbclk"),
> +       DT_CLK("48306200.pwm", "tbclk", "ehrpwm3_tbclk"),
> +       DT_CLK("48308200.pwm", "tbclk", "ehrpwm4_tbclk"),
> +       DT_CLK("4830a200.pwm", "tbclk", "ehrpwm5_tbclk"),
>         { .node_name =3D NULL },
>  };
>  =

> -- =

> 2.7.0
>=20

Re: [PATCH v8 1/9] clk: ti: am335x/am4372: Add tbclk to pwm node

[Franklin S Cooper Jr.]

On 07/11/2016 05:20 PM, Michael Turquette wrote:
> Quoting Franklin S Cooper Jr (2016-05-03 08:56:47)
>> Add tblck to the pwm nodes. This insures that the ehrpwm driver has access
> 
> s/tblck/tbclk/
> 
> I see you have acks already. What tree should this patch go through?


I believe it went through Tero's tree. I currently see it in linux-next.
> 
> Regards,
> Mike
> 
>> to the time-based clk.
>>
>> Do not remove similar entries for ehrpwm node. Later patches will switch
>> from using ehrpwm node name to pwm. But to maintain ABI compatibility we
>> shouldn't remove the old entries.
>>
>> Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
>> Acked-by: Stephen Boyd <sboyd@codeaurora.org>
>> Acked-by: Tero Kristo <t-kristo@ti.com>
>> ---
>>  drivers/clk/ti/clk-33xx.c | 3 +++
>>  drivers/clk/ti/clk-43xx.c | 6 ++++++
>>  2 files changed, 9 insertions(+)
>>
>> diff --git a/drivers/clk/ti/clk-33xx.c b/drivers/clk/ti/clk-33xx.c
>> index ef2ec64..0e47d95 100644
>> --- a/drivers/clk/ti/clk-33xx.c
>> +++ b/drivers/clk/ti/clk-33xx.c
>> @@ -108,6 +108,9 @@ static struct ti_dt_clk am33xx_clks[] = {
>>         DT_CLK("48300200.ehrpwm", "tbclk", "ehrpwm0_tbclk"),
>>         DT_CLK("48302200.ehrpwm", "tbclk", "ehrpwm1_tbclk"),
>>         DT_CLK("48304200.ehrpwm", "tbclk", "ehrpwm2_tbclk"),
>> +       DT_CLK("48300200.pwm", "tbclk", "ehrpwm0_tbclk"),
>> +       DT_CLK("48302200.pwm", "tbclk", "ehrpwm1_tbclk"),
>> +       DT_CLK("48304200.pwm", "tbclk", "ehrpwm2_tbclk"),
>>         { .node_name = NULL },
>>  };
>>  
>> diff --git a/drivers/clk/ti/clk-43xx.c b/drivers/clk/ti/clk-43xx.c
>> index 097fc90..7255aa8 100644
>> --- a/drivers/clk/ti/clk-43xx.c
>> +++ b/drivers/clk/ti/clk-43xx.c
>> @@ -115,6 +115,12 @@ static struct ti_dt_clk am43xx_clks[] = {
>>         DT_CLK("48306200.ehrpwm", "tbclk", "ehrpwm3_tbclk"),
>>         DT_CLK("48308200.ehrpwm", "tbclk", "ehrpwm4_tbclk"),
>>         DT_CLK("4830a200.ehrpwm", "tbclk", "ehrpwm5_tbclk"),
>> +       DT_CLK("48300200.pwm", "tbclk", "ehrpwm0_tbclk"),
>> +       DT_CLK("48302200.pwm", "tbclk", "ehrpwm1_tbclk"),
>> +       DT_CLK("48304200.pwm", "tbclk", "ehrpwm2_tbclk"),
>> +       DT_CLK("48306200.pwm", "tbclk", "ehrpwm3_tbclk"),
>> +       DT_CLK("48308200.pwm", "tbclk", "ehrpwm4_tbclk"),
>> +       DT_CLK("4830a200.pwm", "tbclk", "ehrpwm5_tbclk"),
>>         { .node_name = NULL },
>>  };
>>  
>> -- 
>> 2.7.0
>>