* [PATCH 0/5] Add core MSM8956/76 SoC support drivers
@ 2019-09-21 10:12 kholk11
2019-09-21 10:12 ` [PATCH 1/5] pinctrl: qcom: Add a pinctrl driver for MSM8976 and 8956 kholk11
` (3 more replies)
0 siblings, 4 replies; 12+ messages in thread
From: kholk11 @ 2019-09-21 10:12 UTC (permalink / raw)
To: linux-arm-msm
Cc: kholk11, marijns95, agross, mturquette, sboyd, robh+dt,
mark.rutland, bjorn.andersson, linus.walleij, linux-clk,
linux-gpio
From: AngeloGioacchino Del Regno <kholk11@gmail.com>
This patch series adds support for the core components that are
required to run the MSM8956 (and MSM8976) SoCs, such as pinctrl,
GCC clocks, RPM power domains.
The personal aim is to upstream MSM8956 as much as possible.
This code has been tested on two Sony phones featuring the Qualcomm
MSM8956 SoC.
Angelo G. Del Regno (5):
pinctrl: qcom: Add a pinctrl driver for MSM8976 and 8956
clk: qcom: Add MSM8976/56 Global Clock Controller (GCC) driver
soc: qcom: smd-rpm: Add MSM8976 compatible
dt-bindings: power: Add missing rpmpd smd performance level
soc: qcom: rpmpd: Add rpm power domains for msm8956
.../devicetree/bindings/clock/qcom,gcc.txt | 1 +
.../bindings/pinctrl/qcom,msm8976-pinctrl.txt | 183 +
.../devicetree/bindings/power/qcom,rpmpd.txt | 1 +
.../bindings/soc/qcom/qcom,smd-rpm.txt | 1 +
drivers/clk/qcom/Kconfig | 8 +
drivers/clk/qcom/Makefile | 1 +
drivers/clk/qcom/gcc-msm8976.c | 4215 +++++++++++++++++
drivers/pinctrl/qcom/Kconfig | 10 +
drivers/pinctrl/qcom/Makefile | 1 +
drivers/pinctrl/qcom/pinctrl-msm8976.c | 1128 +++++
drivers/soc/qcom/rpmpd.c | 23 +
drivers/soc/qcom/smd-rpm.c | 1 +
include/dt-bindings/clock/qcom,gcc-msm8976.h | 293 ++
include/dt-bindings/power/qcom-rpmpd.h | 9 +
14 files changed, 5875 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
create mode 100644 drivers/clk/qcom/gcc-msm8976.c
create mode 100644 drivers/pinctrl/qcom/pinctrl-msm8976.c
create mode 100644 include/dt-bindings/clock/qcom,gcc-msm8976.h
--
2.21.0
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 1/5] pinctrl: qcom: Add a pinctrl driver for MSM8976 and 8956
2019-09-21 10:12 [PATCH 0/5] Add core MSM8956/76 SoC support drivers kholk11
@ 2019-09-21 10:12 ` kholk11
2019-10-04 21:16 ` Linus Walleij
2019-10-05 3:59 ` Bjorn Andersson
2019-09-21 10:12 ` [PATCH 3/5] soc: qcom: smd-rpm: Add MSM8976 compatible kholk11
` (2 subsequent siblings)
3 siblings, 2 replies; 12+ messages in thread
From: kholk11 @ 2019-09-21 10:12 UTC (permalink / raw)
To: linux-arm-msm
Cc: kholk11, marijns95, agross, mturquette, sboyd, robh+dt,
mark.rutland, bjorn.andersson, linus.walleij, linux-clk,
linux-gpio
From: "Angelo G. Del Regno" <kholk11@gmail.com>
Add the pinctrl driver to support pin configuration with the
pinctrl framework on MSM8976, MSM8956, APQ8056, APQ8076.
Signed-off-by: Angelo G. Del Regno <kholk11@gmail.com>
---
.../bindings/pinctrl/qcom,msm8976-pinctrl.txt | 183 +++
drivers/pinctrl/qcom/Kconfig | 10 +
drivers/pinctrl/qcom/Makefile | 1 +
drivers/pinctrl/qcom/pinctrl-msm8976.c | 1128 +++++++++++++++++
4 files changed, 1322 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
create mode 100644 drivers/pinctrl/qcom/pinctrl-msm8976.c
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
new file mode 100644
index 000000000000..4e944f84b7d7
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
@@ -0,0 +1,183 @@
+Qualcomm MSM8976 TLMM block
+
+This binding describes the Top Level Mode Multiplexer block found in the
+MSM8956 and MSM8976 platforms.
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be "qcom,msm8976-pinctrl"
+
+- reg:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: the base address and size of the TLMM register space.
+
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: should specify the TLMM summary IRQ.
+
+- interrupt-controller:
+ Usage: required
+ Value type: <none>
+ Definition: identifies this node as an interrupt controller
+
+- #interrupt-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: must be 2. Specifying the pin number and flags, as defined
+ in <dt-bindings/interrupt-controller/irq.h>
+
+- gpio-controller:
+ Usage: required
+ Value type: <none>
+ Definition: identifies this node as a gpio controller
+
+- #gpio-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: must be 2. Specifying the pin number and flags, as defined
+ in <dt-bindings/gpio/gpio.h>
+
+- gpio-ranges:
+ Usage: required
+ Definition: see ../gpio/gpio.txt
+
+- gpio-reserved-ranges:
+ Usage: optional
+ Definition: see ../gpio/gpio.txt
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+
+PIN CONFIGURATION NODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+ Usage: required
+ Value type: <string-array>
+ Definition: List of gpio pins affected by the properties specified in
+ this subnode.
+
+ Valid pins are:
+ gpio0-gpio145
+ Supports mux, bias and drive-strength
+
+ sdc1_clk, sdc1_cmd, sdc1_data,
+ sdc2_clk, sdc2_cmd, sdc2_data,
+ sdc3_clk, sdc3_cmd, sdc3_data
+ Supports bias and drive-strength
+
+- function:
+ Usage: required
+ Value type: <string>
+ Definition: Specify the alternative function to be configured for the
+ specified pins. Functions are only valid for gpio pins.
+ Valid values are:
+
+ gpio, blsp_uart1, blsp_spi1, smb_int, blsp_i2c1, blsp_spi2,
+ blsp_uart2, blsp_i2c2, gcc_gp1_clk_b, blsp_spi3,
+ qdss_tracedata_b, blsp_i2c3, gcc_gp2_clk_b, gcc_gp3_clk_b,
+ blsp_spi4, cap_int, blsp_i2c4, blsp_spi5, blsp_uart5,
+ qdss_traceclk_a, m_voc, blsp_i2c5, qdss_tracectl_a,
+ qdss_tracedata_a, blsp_spi6, blsp_uart6, qdss_tracectl_b,
+ blsp_i2c6, qdss_traceclk_b, mdp_vsync, pri_mi2s_mclk_a,
+ sec_mi2s_mclk_a, cam_mclk, cci0_i2c, cci1_i2c, blsp1_spi,
+ blsp3_spi, gcc_gp1_clk_a, gcc_gp2_clk_a, gcc_gp3_clk_a,
+ uim_batt, sd_write, uim1_data, uim1_clk, uim1_reset,
+ uim1_present, uim2_data, uim2_clk, uim2_reset,
+ uim2_present, ts_xvdd, mipi_dsi0, us_euro, ts_resout,
+ ts_sample, sec_mi2s_mclk_b, pri_mi2s, codec_reset,
+ cdc_pdm0, us_emitter, pri_mi2s_mclk_b, pri_mi2s_mclk_c,
+ lpass_slimbus, lpass_slimbus0, lpass_slimbus1, codec_int1,
+ codec_int2, wcss_bt, sdc3, wcss_wlan2, wcss_wlan1,
+ wcss_wlan0, wcss_wlan, wcss_fm, key_volp, key_snapshot,
+ key_focus, key_home, pwr_down, dmic0_clk, hdmi_int,
+ dmic0_data, wsa_vi, wsa_en, blsp_spi8, wsa_irq, blsp_i2c8,
+ pa_indicator, modem_tsync, ssbi_wtr1, gsm1_tx, gsm0_tx,
+ sdcard_det, sec_mi2s, ss_switch,
+
+- bias-disable:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configured as no pull.
+
+- bias-pull-down:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configured as pull down.
+
+- bias-pull-up:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configured as pull up.
+
+- output-high:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in output mode, driven
+ high.
+ Not valid for sdc pins.
+
+- output-low:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in output mode, driven
+ low.
+ Not valid for sdc pins.
+
+- drive-strength:
+ Usage: optional
+ Value type: <u32>
+ Definition: Selects the drive strength for the specified pins, in mA.
+ Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
+
+Example:
+
+ tlmm: pinctrl@1000000 {
+ compatible = "qcom,msm8976-pinctrl";
+ reg = <0x1000000 0x300000>;
+ interrupts = <0 208 0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&tlmm 0 0 145>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ blsp1_uart2_active: blsp1_uart2_active {
+ mux {
+ pins = "gpio4", "gpio5", "gpio6", "gpio7";
+ function = "blsp_uart2";
+ };
+
+ config {
+ pins = "gpio4", "gpio5", "gpio6", "gpio7";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+ };
diff --git a/drivers/pinctrl/qcom/Kconfig b/drivers/pinctrl/qcom/Kconfig
index 8e14a5f2e970..1c2c1ac0bfd2 100644
--- a/drivers/pinctrl/qcom/Kconfig
+++ b/drivers/pinctrl/qcom/Kconfig
@@ -90,6 +90,16 @@ config PINCTRL_MSM8916
This is the pinctrl, pinmux, pinconf and gpiolib driver for the
Qualcomm TLMM block found on the Qualcomm 8916 platform.
+config PINCTRL_MSM8976
+ tristate "Qualcomm 8976 pin controller driver"
+ depends on GPIOLIB && OF
+ select PINCTRL_MSM
+ help
+ This is the pinctrl, pinmux, pinconf and gpiolib driver for the
+ Qualcomm TLMM block found on the Qualcomm MSM8976 platform.
+ The Qualcomm MSM8956, APQ8056, APQ8076 platforms are also
+ supported by this driver.
+
config PINCTRL_MSM8994
tristate "Qualcomm 8994 pin controller driver"
depends on GPIOLIB && OF
diff --git a/drivers/pinctrl/qcom/Makefile b/drivers/pinctrl/qcom/Makefile
index ebe906872272..a720b76c2d12 100644
--- a/drivers/pinctrl/qcom/Makefile
+++ b/drivers/pinctrl/qcom/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_PINCTRL_MSM8660) += pinctrl-msm8660.o
obj-$(CONFIG_PINCTRL_MSM8960) += pinctrl-msm8960.o
obj-$(CONFIG_PINCTRL_MSM8X74) += pinctrl-msm8x74.o
obj-$(CONFIG_PINCTRL_MSM8916) += pinctrl-msm8916.o
+obj-$(CONFIG_PINCTRL_MSM8976) += pinctrl-msm8976.o
obj-$(CONFIG_PINCTRL_MSM8994) += pinctrl-msm8994.o
obj-$(CONFIG_PINCTRL_MSM8996) += pinctrl-msm8996.o
obj-$(CONFIG_PINCTRL_MSM8998) += pinctrl-msm8998.o
diff --git a/drivers/pinctrl/qcom/pinctrl-msm8976.c b/drivers/pinctrl/qcom/pinctrl-msm8976.c
new file mode 100644
index 000000000000..6b0969a3033f
--- /dev/null
+++ b/drivers/pinctrl/qcom/pinctrl-msm8976.c
@@ -0,0 +1,1128 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2015-2016, The Linux Foundation. All rights reserved.
+ *
+ * Copyright (c) 2016, AngeloGioacchino Del Regno <kholk11@gmail.com>
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-msm.h"
+
+#define FUNCTION(fname) \
+ [msm_mux_##fname] = { \
+ .name = #fname, \
+ .groups = fname##_groups, \
+ .ngroups = ARRAY_SIZE(fname##_groups), \
+ }
+
+#define REG_BASE 0x0
+#define REG_SIZE 0x1000
+#define PINGROUP(id, f1, f2, f3, f4, f5, f6, f7, f8, f9) \
+ { \
+ .name = "gpio" #id, \
+ .pins = gpio##id##_pins, \
+ .npins = ARRAY_SIZE(gpio##id##_pins), \
+ .funcs = (int[]){ \
+ msm_mux_gpio, /* gpio mode */ \
+ msm_mux_##f1, \
+ msm_mux_##f2, \
+ msm_mux_##f3, \
+ msm_mux_##f4, \
+ msm_mux_##f5, \
+ msm_mux_##f6, \
+ msm_mux_##f7, \
+ msm_mux_##f8, \
+ msm_mux_##f9 \
+ }, \
+ .nfuncs = 10, \
+ .ctl_reg = REG_BASE + REG_SIZE * id, \
+ .io_reg = REG_BASE + 0x4 + REG_SIZE * id, \
+ .intr_cfg_reg = REG_BASE + 0x8 + REG_SIZE * id, \
+ .intr_status_reg = REG_BASE + 0xc + REG_SIZE * id, \
+ .intr_target_reg = REG_BASE + 0x8 + REG_SIZE * id, \
+ .mux_bit = 2, \
+ .pull_bit = 0, \
+ .drv_bit = 6, \
+ .oe_bit = 9, \
+ .in_bit = 0, \
+ .out_bit = 1, \
+ .intr_enable_bit = 0, \
+ .intr_status_bit = 0, \
+ .intr_target_bit = 5, \
+ .intr_target_kpss_val = 4, \
+ .intr_raw_status_bit = 4, \
+ .intr_polarity_bit = 1, \
+ .intr_detection_bit = 2, \
+ .intr_detection_width = 2, \
+ }
+
+#define SDC_QDSD_PINGROUP(pg_name, ctl, pull, drv) \
+ { \
+ .name = #pg_name, \
+ .pins = pg_name##_pins, \
+ .npins = ARRAY_SIZE(pg_name##_pins), \
+ .ctl_reg = ctl, \
+ .io_reg = 0, \
+ .intr_cfg_reg = 0, \
+ .intr_status_reg = 0, \
+ .intr_target_reg = 0, \
+ .mux_bit = -1, \
+ .pull_bit = pull, \
+ .drv_bit = drv, \
+ .oe_bit = -1, \
+ .in_bit = -1, \
+ .out_bit = -1, \
+ .intr_enable_bit = -1, \
+ .intr_status_bit = -1, \
+ .intr_target_bit = -1, \
+ .intr_raw_status_bit = -1, \
+ .intr_polarity_bit = -1, \
+ .intr_detection_bit = -1, \
+ .intr_detection_width = -1, \
+ }
+static const struct pinctrl_pin_desc msm8976_pins[] = {
+ PINCTRL_PIN(0, "GPIO_0"),
+ PINCTRL_PIN(1, "GPIO_1"),
+ PINCTRL_PIN(2, "GPIO_2"),
+ PINCTRL_PIN(3, "GPIO_3"),
+ PINCTRL_PIN(4, "GPIO_4"),
+ PINCTRL_PIN(5, "GPIO_5"),
+ PINCTRL_PIN(6, "GPIO_6"),
+ PINCTRL_PIN(7, "GPIO_7"),
+ PINCTRL_PIN(8, "GPIO_8"),
+ PINCTRL_PIN(9, "GPIO_9"),
+ PINCTRL_PIN(10, "GPIO_10"),
+ PINCTRL_PIN(11, "GPIO_11"),
+ PINCTRL_PIN(12, "GPIO_12"),
+ PINCTRL_PIN(13, "GPIO_13"),
+ PINCTRL_PIN(14, "GPIO_14"),
+ PINCTRL_PIN(15, "GPIO_15"),
+ PINCTRL_PIN(16, "GPIO_16"),
+ PINCTRL_PIN(17, "GPIO_17"),
+ PINCTRL_PIN(18, "GPIO_18"),
+ PINCTRL_PIN(19, "GPIO_19"),
+ PINCTRL_PIN(20, "GPIO_20"),
+ PINCTRL_PIN(21, "GPIO_21"),
+ PINCTRL_PIN(22, "GPIO_22"),
+ PINCTRL_PIN(23, "GPIO_23"),
+ PINCTRL_PIN(24, "GPIO_24"),
+ PINCTRL_PIN(25, "GPIO_25"),
+ PINCTRL_PIN(26, "GPIO_26"),
+ PINCTRL_PIN(27, "GPIO_27"),
+ PINCTRL_PIN(28, "GPIO_28"),
+ PINCTRL_PIN(29, "GPIO_29"),
+ PINCTRL_PIN(30, "GPIO_30"),
+ PINCTRL_PIN(31, "GPIO_31"),
+ PINCTRL_PIN(32, "GPIO_32"),
+ PINCTRL_PIN(33, "GPIO_33"),
+ PINCTRL_PIN(34, "GPIO_34"),
+ PINCTRL_PIN(35, "GPIO_35"),
+ PINCTRL_PIN(36, "GPIO_36"),
+ PINCTRL_PIN(37, "GPIO_37"),
+ PINCTRL_PIN(38, "GPIO_38"),
+ PINCTRL_PIN(39, "GPIO_39"),
+ PINCTRL_PIN(40, "GPIO_40"),
+ PINCTRL_PIN(41, "GPIO_41"),
+ PINCTRL_PIN(42, "GPIO_42"),
+ PINCTRL_PIN(43, "GPIO_43"),
+ PINCTRL_PIN(44, "GPIO_44"),
+ PINCTRL_PIN(45, "GPIO_45"),
+ PINCTRL_PIN(46, "GPIO_46"),
+ PINCTRL_PIN(47, "GPIO_47"),
+ PINCTRL_PIN(48, "GPIO_48"),
+ PINCTRL_PIN(49, "GPIO_49"),
+ PINCTRL_PIN(50, "GPIO_50"),
+ PINCTRL_PIN(51, "GPIO_51"),
+ PINCTRL_PIN(52, "GPIO_52"),
+ PINCTRL_PIN(53, "GPIO_53"),
+ PINCTRL_PIN(54, "GPIO_54"),
+ PINCTRL_PIN(55, "GPIO_55"),
+ PINCTRL_PIN(56, "GPIO_56"),
+ PINCTRL_PIN(57, "GPIO_57"),
+ PINCTRL_PIN(58, "GPIO_58"),
+ PINCTRL_PIN(59, "GPIO_59"),
+ PINCTRL_PIN(60, "GPIO_60"),
+ PINCTRL_PIN(61, "GPIO_61"),
+ PINCTRL_PIN(62, "GPIO_62"),
+ PINCTRL_PIN(63, "GPIO_63"),
+ PINCTRL_PIN(64, "GPIO_64"),
+ PINCTRL_PIN(65, "GPIO_65"),
+ PINCTRL_PIN(66, "GPIO_66"),
+ PINCTRL_PIN(67, "GPIO_67"),
+ PINCTRL_PIN(68, "GPIO_68"),
+ PINCTRL_PIN(69, "GPIO_69"),
+ PINCTRL_PIN(70, "GPIO_70"),
+ PINCTRL_PIN(71, "GPIO_71"),
+ PINCTRL_PIN(72, "GPIO_72"),
+ PINCTRL_PIN(73, "GPIO_73"),
+ PINCTRL_PIN(74, "GPIO_74"),
+ PINCTRL_PIN(75, "GPIO_75"),
+ PINCTRL_PIN(76, "GPIO_76"),
+ PINCTRL_PIN(77, "GPIO_77"),
+ PINCTRL_PIN(78, "GPIO_78"),
+ PINCTRL_PIN(79, "GPIO_79"),
+ PINCTRL_PIN(80, "GPIO_80"),
+ PINCTRL_PIN(81, "GPIO_81"),
+ PINCTRL_PIN(82, "GPIO_82"),
+ PINCTRL_PIN(83, "GPIO_83"),
+ PINCTRL_PIN(84, "GPIO_84"),
+ PINCTRL_PIN(85, "GPIO_85"),
+ PINCTRL_PIN(86, "GPIO_86"),
+ PINCTRL_PIN(87, "GPIO_87"),
+ PINCTRL_PIN(88, "GPIO_88"),
+ PINCTRL_PIN(89, "GPIO_89"),
+ PINCTRL_PIN(90, "GPIO_90"),
+ PINCTRL_PIN(91, "GPIO_91"),
+ PINCTRL_PIN(92, "GPIO_92"),
+ PINCTRL_PIN(93, "GPIO_93"),
+ PINCTRL_PIN(94, "GPIO_94"),
+ PINCTRL_PIN(95, "GPIO_95"),
+ PINCTRL_PIN(96, "GPIO_96"),
+ PINCTRL_PIN(97, "GPIO_97"),
+ PINCTRL_PIN(98, "GPIO_98"),
+ PINCTRL_PIN(99, "GPIO_99"),
+ PINCTRL_PIN(100, "GPIO_100"),
+ PINCTRL_PIN(101, "GPIO_101"),
+ PINCTRL_PIN(102, "GPIO_102"),
+ PINCTRL_PIN(103, "GPIO_103"),
+ PINCTRL_PIN(104, "GPIO_104"),
+ PINCTRL_PIN(105, "GPIO_105"),
+ PINCTRL_PIN(106, "GPIO_106"),
+ PINCTRL_PIN(107, "GPIO_107"),
+ PINCTRL_PIN(108, "GPIO_108"),
+ PINCTRL_PIN(109, "GPIO_109"),
+ PINCTRL_PIN(110, "GPIO_110"),
+ PINCTRL_PIN(111, "GPIO_111"),
+ PINCTRL_PIN(112, "GPIO_112"),
+ PINCTRL_PIN(113, "GPIO_113"),
+ PINCTRL_PIN(114, "GPIO_114"),
+ PINCTRL_PIN(115, "GPIO_115"),
+ PINCTRL_PIN(116, "GPIO_116"),
+ PINCTRL_PIN(117, "GPIO_117"),
+ PINCTRL_PIN(118, "GPIO_118"),
+ PINCTRL_PIN(119, "GPIO_119"),
+ PINCTRL_PIN(120, "GPIO_120"),
+ PINCTRL_PIN(121, "GPIO_121"),
+ PINCTRL_PIN(122, "GPIO_122"),
+ PINCTRL_PIN(123, "GPIO_123"),
+ PINCTRL_PIN(124, "GPIO_124"),
+ PINCTRL_PIN(125, "GPIO_125"),
+ PINCTRL_PIN(126, "GPIO_126"),
+ PINCTRL_PIN(127, "GPIO_127"),
+ PINCTRL_PIN(128, "GPIO_128"),
+ PINCTRL_PIN(129, "GPIO_129"),
+ PINCTRL_PIN(130, "GPIO_130"),
+ PINCTRL_PIN(131, "GPIO_131"),
+ PINCTRL_PIN(132, "GPIO_132"),
+ PINCTRL_PIN(133, "GPIO_133"),
+ PINCTRL_PIN(134, "GPIO_134"),
+ PINCTRL_PIN(135, "GPIO_135"),
+ PINCTRL_PIN(136, "GPIO_136"),
+ PINCTRL_PIN(137, "GPIO_137"),
+ PINCTRL_PIN(138, "GPIO_138"),
+ PINCTRL_PIN(139, "GPIO_139"),
+ PINCTRL_PIN(140, "GPIO_140"),
+ PINCTRL_PIN(141, "GPIO_141"),
+ PINCTRL_PIN(142, "GPIO_142"),
+ PINCTRL_PIN(143, "GPIO_143"),
+ PINCTRL_PIN(144, "GPIO_144"),
+ PINCTRL_PIN(145, "SDC1_CLK"),
+ PINCTRL_PIN(146, "SDC1_CMD"),
+ PINCTRL_PIN(147, "SDC1_DATA"),
+ PINCTRL_PIN(148, "SDC1_RCLK"),
+ PINCTRL_PIN(149, "SDC2_CLK"),
+ PINCTRL_PIN(150, "SDC2_CMD"),
+ PINCTRL_PIN(151, "SDC2_DATA"),
+ PINCTRL_PIN(152, "QDSD_CLK"),
+ PINCTRL_PIN(153, "QDSD_CMD"),
+ PINCTRL_PIN(154, "QDSD_DATA0"),
+ PINCTRL_PIN(155, "QDSD_DATA1"),
+ PINCTRL_PIN(156, "QDSD_DATA2"),
+ PINCTRL_PIN(157, "QDSD_DATA3"),
+};
+
+#define DECLARE_MSM_GPIO_PINS(pin) \
+ static const unsigned int gpio##pin##_pins[] = { pin }
+DECLARE_MSM_GPIO_PINS(0);
+DECLARE_MSM_GPIO_PINS(1);
+DECLARE_MSM_GPIO_PINS(2);
+DECLARE_MSM_GPIO_PINS(3);
+DECLARE_MSM_GPIO_PINS(4);
+DECLARE_MSM_GPIO_PINS(5);
+DECLARE_MSM_GPIO_PINS(6);
+DECLARE_MSM_GPIO_PINS(7);
+DECLARE_MSM_GPIO_PINS(8);
+DECLARE_MSM_GPIO_PINS(9);
+DECLARE_MSM_GPIO_PINS(10);
+DECLARE_MSM_GPIO_PINS(11);
+DECLARE_MSM_GPIO_PINS(12);
+DECLARE_MSM_GPIO_PINS(13);
+DECLARE_MSM_GPIO_PINS(14);
+DECLARE_MSM_GPIO_PINS(15);
+DECLARE_MSM_GPIO_PINS(16);
+DECLARE_MSM_GPIO_PINS(17);
+DECLARE_MSM_GPIO_PINS(18);
+DECLARE_MSM_GPIO_PINS(19);
+DECLARE_MSM_GPIO_PINS(20);
+DECLARE_MSM_GPIO_PINS(21);
+DECLARE_MSM_GPIO_PINS(22);
+DECLARE_MSM_GPIO_PINS(23);
+DECLARE_MSM_GPIO_PINS(24);
+DECLARE_MSM_GPIO_PINS(25);
+DECLARE_MSM_GPIO_PINS(26);
+DECLARE_MSM_GPIO_PINS(27);
+DECLARE_MSM_GPIO_PINS(28);
+DECLARE_MSM_GPIO_PINS(29);
+DECLARE_MSM_GPIO_PINS(30);
+DECLARE_MSM_GPIO_PINS(31);
+DECLARE_MSM_GPIO_PINS(32);
+DECLARE_MSM_GPIO_PINS(33);
+DECLARE_MSM_GPIO_PINS(34);
+DECLARE_MSM_GPIO_PINS(35);
+DECLARE_MSM_GPIO_PINS(36);
+DECLARE_MSM_GPIO_PINS(37);
+DECLARE_MSM_GPIO_PINS(38);
+DECLARE_MSM_GPIO_PINS(39);
+DECLARE_MSM_GPIO_PINS(40);
+DECLARE_MSM_GPIO_PINS(41);
+DECLARE_MSM_GPIO_PINS(42);
+DECLARE_MSM_GPIO_PINS(43);
+DECLARE_MSM_GPIO_PINS(44);
+DECLARE_MSM_GPIO_PINS(45);
+DECLARE_MSM_GPIO_PINS(46);
+DECLARE_MSM_GPIO_PINS(47);
+DECLARE_MSM_GPIO_PINS(48);
+DECLARE_MSM_GPIO_PINS(49);
+DECLARE_MSM_GPIO_PINS(50);
+DECLARE_MSM_GPIO_PINS(51);
+DECLARE_MSM_GPIO_PINS(52);
+DECLARE_MSM_GPIO_PINS(53);
+DECLARE_MSM_GPIO_PINS(54);
+DECLARE_MSM_GPIO_PINS(55);
+DECLARE_MSM_GPIO_PINS(56);
+DECLARE_MSM_GPIO_PINS(57);
+DECLARE_MSM_GPIO_PINS(58);
+DECLARE_MSM_GPIO_PINS(59);
+DECLARE_MSM_GPIO_PINS(60);
+DECLARE_MSM_GPIO_PINS(61);
+DECLARE_MSM_GPIO_PINS(62);
+DECLARE_MSM_GPIO_PINS(63);
+DECLARE_MSM_GPIO_PINS(64);
+DECLARE_MSM_GPIO_PINS(65);
+DECLARE_MSM_GPIO_PINS(66);
+DECLARE_MSM_GPIO_PINS(67);
+DECLARE_MSM_GPIO_PINS(68);
+DECLARE_MSM_GPIO_PINS(69);
+DECLARE_MSM_GPIO_PINS(70);
+DECLARE_MSM_GPIO_PINS(71);
+DECLARE_MSM_GPIO_PINS(72);
+DECLARE_MSM_GPIO_PINS(73);
+DECLARE_MSM_GPIO_PINS(74);
+DECLARE_MSM_GPIO_PINS(75);
+DECLARE_MSM_GPIO_PINS(76);
+DECLARE_MSM_GPIO_PINS(77);
+DECLARE_MSM_GPIO_PINS(78);
+DECLARE_MSM_GPIO_PINS(79);
+DECLARE_MSM_GPIO_PINS(80);
+DECLARE_MSM_GPIO_PINS(81);
+DECLARE_MSM_GPIO_PINS(82);
+DECLARE_MSM_GPIO_PINS(83);
+DECLARE_MSM_GPIO_PINS(84);
+DECLARE_MSM_GPIO_PINS(85);
+DECLARE_MSM_GPIO_PINS(86);
+DECLARE_MSM_GPIO_PINS(87);
+DECLARE_MSM_GPIO_PINS(88);
+DECLARE_MSM_GPIO_PINS(89);
+DECLARE_MSM_GPIO_PINS(90);
+DECLARE_MSM_GPIO_PINS(91);
+DECLARE_MSM_GPIO_PINS(92);
+DECLARE_MSM_GPIO_PINS(93);
+DECLARE_MSM_GPIO_PINS(94);
+DECLARE_MSM_GPIO_PINS(95);
+DECLARE_MSM_GPIO_PINS(96);
+DECLARE_MSM_GPIO_PINS(97);
+DECLARE_MSM_GPIO_PINS(98);
+DECLARE_MSM_GPIO_PINS(99);
+DECLARE_MSM_GPIO_PINS(100);
+DECLARE_MSM_GPIO_PINS(101);
+DECLARE_MSM_GPIO_PINS(102);
+DECLARE_MSM_GPIO_PINS(103);
+DECLARE_MSM_GPIO_PINS(104);
+DECLARE_MSM_GPIO_PINS(105);
+DECLARE_MSM_GPIO_PINS(106);
+DECLARE_MSM_GPIO_PINS(107);
+DECLARE_MSM_GPIO_PINS(108);
+DECLARE_MSM_GPIO_PINS(109);
+DECLARE_MSM_GPIO_PINS(110);
+DECLARE_MSM_GPIO_PINS(111);
+DECLARE_MSM_GPIO_PINS(112);
+DECLARE_MSM_GPIO_PINS(113);
+DECLARE_MSM_GPIO_PINS(114);
+DECLARE_MSM_GPIO_PINS(115);
+DECLARE_MSM_GPIO_PINS(116);
+DECLARE_MSM_GPIO_PINS(117);
+DECLARE_MSM_GPIO_PINS(118);
+DECLARE_MSM_GPIO_PINS(119);
+DECLARE_MSM_GPIO_PINS(120);
+DECLARE_MSM_GPIO_PINS(121);
+DECLARE_MSM_GPIO_PINS(122);
+DECLARE_MSM_GPIO_PINS(123);
+DECLARE_MSM_GPIO_PINS(124);
+DECLARE_MSM_GPIO_PINS(125);
+DECLARE_MSM_GPIO_PINS(126);
+DECLARE_MSM_GPIO_PINS(127);
+DECLARE_MSM_GPIO_PINS(128);
+DECLARE_MSM_GPIO_PINS(129);
+DECLARE_MSM_GPIO_PINS(130);
+DECLARE_MSM_GPIO_PINS(131);
+DECLARE_MSM_GPIO_PINS(132);
+DECLARE_MSM_GPIO_PINS(133);
+DECLARE_MSM_GPIO_PINS(134);
+DECLARE_MSM_GPIO_PINS(135);
+DECLARE_MSM_GPIO_PINS(136);
+DECLARE_MSM_GPIO_PINS(137);
+DECLARE_MSM_GPIO_PINS(138);
+DECLARE_MSM_GPIO_PINS(139);
+DECLARE_MSM_GPIO_PINS(140);
+DECLARE_MSM_GPIO_PINS(141);
+DECLARE_MSM_GPIO_PINS(142);
+DECLARE_MSM_GPIO_PINS(143);
+DECLARE_MSM_GPIO_PINS(144);
+
+static const unsigned int sdc1_clk_pins[] = { 145 };
+static const unsigned int sdc1_cmd_pins[] = { 146 };
+static const unsigned int sdc1_data_pins[] = { 147 };
+static const unsigned int sdc1_rclk_pins[] = { 148 };
+static const unsigned int sdc2_clk_pins[] = { 149 };
+static const unsigned int sdc2_cmd_pins[] = { 150 };
+static const unsigned int sdc2_data_pins[] = { 151 };
+static const unsigned int qdsd_clk_pins[] = { 152 };
+static const unsigned int qdsd_cmd_pins[] = { 153 };
+static const unsigned int qdsd_data0_pins[] = { 154 };
+static const unsigned int qdsd_data1_pins[] = { 155 };
+static const unsigned int qdsd_data2_pins[] = { 156 };
+static const unsigned int qdsd_data3_pins[] = { 157 };
+
+enum msm8976_functions {
+ msm_mux_gpio,
+ msm_mux_blsp_uart1,
+ msm_mux_blsp_spi1,
+ msm_mux_smb_int,
+ msm_mux_blsp_i2c1,
+ msm_mux_blsp_spi2,
+ msm_mux_blsp_uart2,
+ msm_mux_blsp_i2c2,
+ msm_mux_gcc_gp1_clk_b,
+ msm_mux_blsp_spi3,
+ msm_mux_qdss_tracedata_b,
+ msm_mux_blsp_i2c3,
+ msm_mux_gcc_gp2_clk_b,
+ msm_mux_gcc_gp3_clk_b,
+ msm_mux_blsp_spi4,
+ msm_mux_cap_int,
+ msm_mux_blsp_i2c4,
+ msm_mux_blsp_spi5,
+ msm_mux_blsp_uart5,
+ msm_mux_qdss_traceclk_a,
+ msm_mux_m_voc,
+ msm_mux_blsp_i2c5,
+ msm_mux_qdss_tracectl_a,
+ msm_mux_qdss_tracedata_a,
+ msm_mux_blsp_spi6,
+ msm_mux_blsp_uart6,
+ msm_mux_qdss_tracectl_b,
+ msm_mux_blsp_i2c6,
+ msm_mux_qdss_traceclk_b,
+ msm_mux_mdp_vsync,
+ msm_mux_pri_mi2s_mclk_a,
+ msm_mux_sec_mi2s_mclk_a,
+ msm_mux_cam_mclk,
+ msm_mux_cci0_i2c,
+ msm_mux_cci1_i2c,
+ msm_mux_blsp1_spi,
+ msm_mux_blsp3_spi,
+ msm_mux_gcc_gp1_clk_a,
+ msm_mux_gcc_gp2_clk_a,
+ msm_mux_gcc_gp3_clk_a,
+ msm_mux_uim_batt,
+ msm_mux_sd_write,
+ msm_mux_uim1_data,
+ msm_mux_uim1_clk,
+ msm_mux_uim1_reset,
+ msm_mux_uim1_present,
+ msm_mux_uim2_data,
+ msm_mux_uim2_clk,
+ msm_mux_uim2_reset,
+ msm_mux_uim2_present,
+ msm_mux_ts_xvdd,
+ msm_mux_mipi_dsi0,
+ msm_mux_us_euro,
+ msm_mux_ts_resout,
+ msm_mux_ts_sample,
+ msm_mux_sec_mi2s_mclk_b,
+ msm_mux_pri_mi2s,
+ msm_mux_codec_reset,
+ msm_mux_cdc_pdm0,
+ msm_mux_us_emitter,
+ msm_mux_pri_mi2s_mclk_b,
+ msm_mux_pri_mi2s_mclk_c,
+ msm_mux_lpass_slimbus,
+ msm_mux_lpass_slimbus0,
+ msm_mux_lpass_slimbus1,
+ msm_mux_codec_int1,
+ msm_mux_codec_int2,
+ msm_mux_wcss_bt,
+ msm_mux_sdc3,
+ msm_mux_wcss_wlan2,
+ msm_mux_wcss_wlan1,
+ msm_mux_wcss_wlan0,
+ msm_mux_wcss_wlan,
+ msm_mux_wcss_fm,
+ msm_mux_key_volp,
+ msm_mux_key_snapshot,
+ msm_mux_key_focus,
+ msm_mux_key_home,
+ msm_mux_pwr_down,
+ msm_mux_dmic0_clk,
+ msm_mux_hdmi_int,
+ msm_mux_dmic0_data,
+ msm_mux_wsa_vi,
+ msm_mux_wsa_en,
+ msm_mux_blsp_spi8,
+ msm_mux_wsa_irq,
+ msm_mux_blsp_i2c8,
+ msm_mux_pa_indicator,
+ msm_mux_modem_tsync,
+ msm_mux_ssbi_wtr1,
+ msm_mux_gsm1_tx,
+ msm_mux_gsm0_tx,
+ msm_mux_sdcard_det,
+ msm_mux_sec_mi2s,
+ msm_mux_ss_switch,
+ msm_mux_NA,
+};
+
+static const char * const gpio_groups[] = {
+ "gpio0", "gpio1", "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7",
+ "gpio8", "gpio9", "gpio10", "gpio11", "gpio12", "gpio13", "gpio14",
+ "gpio15", "gpio16", "gpio17", "gpio18", "gpio19", "gpio20", "gpio21",
+ "gpio22", "gpio23", "gpio24", "gpio25", "gpio26", "gpio27", "gpio28",
+ "gpio29", "gpio30", "gpio31", "gpio32", "gpio33", "gpio34", "gpio35",
+ "gpio36", "gpio37", "gpio38", "gpio39", "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45", "gpio46", "gpio47", "gpio48", "gpio49",
+ "gpio50", "gpio51", "gpio52", "gpio53", "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio58", "gpio59", "gpio60", "gpio61", "gpio62", "gpio63",
+ "gpio64", "gpio65", "gpio66", "gpio67", "gpio68", "gpio69", "gpio70",
+ "gpio71", "gpio72", "gpio73", "gpio74", "gpio75", "gpio76", "gpio77",
+ "gpio78", "gpio79", "gpio80", "gpio81", "gpio82", "gpio83", "gpio84",
+ "gpio85", "gpio86", "gpio87", "gpio88", "gpio89", "gpio90", "gpio91",
+ "gpio92", "gpio93", "gpio94", "gpio95", "gpio96", "gpio97", "gpio98",
+ "gpio99", "gpio100", "gpio101", "gpio102", "gpio103", "gpio104",
+ "gpio105", "gpio106", "gpio107", "gpio108", "gpio109", "gpio110",
+ "gpio111", "gpio112", "gpio113", "gpio114", "gpio115", "gpio116",
+ "gpio117", "gpio118", "gpio119", "gpio120", "gpio121", "gpio122",
+ "gpio123", "gpio124", "gpio125", "gpio126", "gpio127", "gpio128",
+ "gpio129", "gpio130", "gpio131", "gpio132", "gpio133", "gpio134",
+ "gpio135", "gpio136", "gpio137", "gpio138", "gpio139", "gpio140",
+ "gpio141", "gpio142", "gpio143", "gpio144",
+};
+static const char * const blsp_uart1_groups[] = {
+ "gpio0", "gpio1", "gpio2", "gpio3",
+};
+static const char * const blsp_spi1_groups[] = {
+ "gpio0", "gpio1", "gpio2", "gpio3",
+};
+static const char * const smb_int_groups[] = {
+ "gpio1",
+};
+static const char * const blsp_i2c1_groups[] = {
+ "gpio2", "gpio3",
+};
+static const char * const blsp_spi2_groups[] = {
+ "gpio4", "gpio5", "gpio6", "gpio7",
+};
+static const char * const blsp_uart2_groups[] = {
+ "gpio4", "gpio5", "gpio6", "gpio7",
+};
+static const char * const blsp_i2c2_groups[] = {
+ "gpio6", "gpio7",
+};
+static const char * const gcc_gp1_clk_b_groups[] = {
+ "gpio105",
+};
+static const char * const blsp_spi3_groups[] = {
+ "gpio8", "gpio9", "gpio10", "gpio11",
+};
+static const char * const qdss_tracedata_b_groups[] = {
+ "gpio26", "gpio27", "gpio28", "gpio29", "gpio30",
+ "gpio31", "gpio33", "gpio34", "gpio35", "gpio36", "gpio37", "gpio38",
+ "gpio116", "gpio126", "gpio128", "gpio129",
+};
+static const char * const blsp_i2c3_groups[] = {
+ "gpio10", "gpio11",
+};
+static const char * const gcc_gp2_clk_b_groups[] = {
+ "gpio12",
+};
+static const char * const gcc_gp3_clk_b_groups[] = {
+ "gpio13",
+};
+static const char * const blsp_spi4_groups[] = {
+ "gpio12", "gpio13", "gpio14", "gpio15",
+};
+static const char * const cap_int_groups[] = {
+ "gpio13",
+};
+static const char * const blsp_i2c4_groups[] = {
+ "gpio14", "gpio15",
+};
+static const char * const blsp_spi5_groups[] = {
+ "gpio134", "gpio135", "gpio136", "gpio137",
+};
+static const char * const blsp_uart5_groups[] = {
+ "gpio134", "gpio135", "gpio136", "gpio137",
+};
+static const char * const qdss_traceclk_a_groups[] = {
+ "gpio46",
+};
+const char * const m_voc_groups[] = {
+ "gpio123", "gpio124",
+};
+static const char * const blsp_i2c5_groups[] = {
+ "gpio136", "gpio137",
+};
+static const char * const qdss_tracectl_a_groups[] = {
+ "gpio45",
+};
+static const char * const qdss_tracedata_a_groups[] = {
+ "gpio8", "gpio9", "gpio10", "gpio39", "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio47", "gpio48", "gpio62", "gpio69", "gpio120",
+ "gpio121", "gpio130", "gpio131",
+};
+static const char * const blsp_spi6_groups[] = {
+ "gpio20", "gpio21", "gpio22", "gpio23",
+};
+static const char * const blsp_uart6_groups[] = {
+ "gpio20", "gpio21", "gpio22", "gpio23",
+};
+static const char * const qdss_tracectl_b_groups[] = {
+ "gpio5",
+};
+static const char * const blsp_i2c6_groups[] = {
+ "gpio22", "gpio23",
+};
+static const char * const qdss_traceclk_b_groups[] = {
+ "gpio5",
+};
+static const char * const mdp_vsync_groups[] = {
+ "gpio24", "gpio25",
+};
+static const char * const pri_mi2s_mclk_a_groups[] = {
+ "gpio126",
+};
+static const char * const sec_mi2s_mclk_a_groups[] = {
+ "gpio62",
+};
+static const char * const cam_mclk_groups[] = {
+ "gpio26", "gpio27", "gpio28",
+};
+static const char * const cci0_i2c_groups[] = {
+ "gpio30", "gpio29",
+};
+static const char * const cci1_i2c_groups[] = {
+ "gpio104", "gpio103",
+};
+static const char * const blsp1_spi_groups[] = {
+ "gpio101",
+};
+static const char * const blsp3_spi_groups[] = {
+ "gpio106", "gpio107",
+};
+static const char * const gcc_gp1_clk_a_groups[] = {
+ "gpio49",
+};
+static const char * const gcc_gp2_clk_a_groups[] = {
+ "gpio50",
+};
+static const char * const gcc_gp3_clk_a_groups[] = {
+ "gpio51",
+};
+static const char * const uim_batt_groups[] = {
+ "gpio61",
+};
+static const char * const sd_write_groups[] = {
+ "gpio50",
+};
+static const char * const uim2_data_groups[] = {
+ "gpio51",
+};
+static const char * const uim2_clk_groups[] = {
+ "gpio52",
+};
+static const char * const uim2_reset_groups[] = {
+ "gpio53",
+};
+static const char * const uim2_present_groups[] = {
+ "gpio54",
+};
+static const char * const uim1_data_groups[] = {
+ "gpio55",
+};
+static const char * const uim1_clk_groups[] = {
+ "gpio56",
+};
+static const char * const uim1_reset_groups[] = {
+ "gpio57",
+};
+static const char * const uim1_present_groups[] = {
+ "gpio58",
+};
+static const char * const ts_xvdd_groups[] = {
+ "gpio60",
+};
+static const char * const mipi_dsi0_groups[] = {
+ "gpio61",
+};
+static const char * const us_euro_groups[] = {
+ "gpio63",
+};
+static const char * const ts_resout_groups[] = {
+ "gpio64",
+};
+static const char * const ts_sample_groups[] = {
+ "gpio65",
+};
+static const char * const sec_mi2s_mclk_b_groups[] = {
+ "gpio66",
+};
+static const char * const pri_mi2s_groups[] = {
+ "gpio122", "gpio123", "gpio124", "gpio125", "gpio127",
+};
+static const char * const codec_reset_groups[] = {
+ "gpio67",
+};
+static const char * const cdc_pdm0_groups[] = {
+ "gpio116", "gpio117", "gpio118", "gpio119", "gpio120", "gpio121",
+};
+static const char * const us_emitter_groups[] = {
+ "gpio68",
+};
+static const char * const pri_mi2s_mclk_b_groups[] = {
+ "gpio62",
+};
+static const char * const pri_mi2s_mclk_c_groups[] = {
+ "gpio116",
+};
+static const char * const lpass_slimbus_groups[] = {
+ "gpio117",
+};
+static const char * const lpass_slimbus0_groups[] = {
+ "gpio118",
+};
+static const char * const lpass_slimbus1_groups[] = {
+ "gpio119",
+};
+static const char * const codec_int1_groups[] = {
+ "gpio73",
+};
+static const char * const codec_int2_groups[] = {
+ "gpio74",
+};
+static const char * const wcss_bt_groups[] = {
+ "gpio39", "gpio47", "gpio88",
+};
+static const char * const sdc3_groups[] = {
+ "gpio39", "gpio40", "gpio41",
+ "gpio42", "gpio43", "gpio44",
+};
+static const char * const wcss_wlan2_groups[] = {
+ "gpio40",
+};
+static const char * const wcss_wlan1_groups[] = {
+ "gpio41",
+};
+static const char * const wcss_wlan0_groups[] = {
+ "gpio42",
+};
+static const char * const wcss_wlan_groups[] = {
+ "gpio43", "gpio44",
+};
+static const char * const wcss_fm_groups[] = {
+ "gpio45", "gpio46",
+};
+static const char * const key_volp_groups[] = {
+ "gpio85",
+};
+static const char * const key_snapshot_groups[] = {
+ "gpio86",
+};
+static const char * const key_focus_groups[] = {
+ "gpio87",
+};
+static const char * const key_home_groups[] = {
+ "gpio88",
+};
+static const char * const pwr_down_groups[] = {
+ "gpio89",
+};
+static const char * const dmic0_clk_groups[] = {
+ "gpio66",
+};
+static const char * const hdmi_int_groups[] = {
+ "gpio90",
+};
+static const char * const dmic0_data_groups[] = {
+ "gpio67",
+};
+static const char * const wsa_vi_groups[] = {
+ "gpio108", "gpio109",
+};
+static const char * const wsa_en_groups[] = {
+ "gpio96",
+};
+static const char * const blsp_spi8_groups[] = {
+ "gpio16", "gpio17", "gpio18", "gpio19",
+};
+static const char * const wsa_irq_groups[] = {
+ "gpio97",
+};
+static const char * const blsp_i2c8_groups[] = {
+ "gpio18", "gpio19",
+};
+static const char * const pa_indicator_groups[] = {
+ "gpio92",
+};
+static const char * const modem_tsync_groups[] = {
+ "gpio93",
+};
+static const char * const nav_tsync_groups[] = {
+ "gpio93",
+};
+static const char * const ssbi_wtr1_groups[] = {
+ "gpio79", "gpio94",
+};
+static const char * const gsm1_tx_groups[] = {
+ "gpio95",
+};
+static const char * const gsm0_tx_groups[] = {
+ "gpio99",
+};
+static const char * const sdcard_det_groups[] = {
+ "gpio133",
+};
+static const char * const sec_mi2s_groups[] = {
+ "gpio102", "gpio105", "gpio134", "gpio135",
+};
+
+static const char * const ss_switch_groups[] = {
+ "gpio139",
+};
+
+static const struct msm_function msm8976_functions[] = {
+ FUNCTION(gpio),
+ FUNCTION(blsp_spi1),
+ FUNCTION(smb_int),
+ FUNCTION(blsp_i2c1),
+ FUNCTION(blsp_spi2),
+ FUNCTION(blsp_uart1),
+ FUNCTION(blsp_uart2),
+ FUNCTION(blsp_i2c2),
+ FUNCTION(gcc_gp1_clk_b),
+ FUNCTION(blsp_spi3),
+ FUNCTION(qdss_tracedata_b),
+ FUNCTION(blsp_i2c3),
+ FUNCTION(gcc_gp2_clk_b),
+ FUNCTION(gcc_gp3_clk_b),
+ FUNCTION(blsp_spi4),
+ FUNCTION(cap_int),
+ FUNCTION(blsp_i2c4),
+ FUNCTION(blsp_spi5),
+ FUNCTION(blsp_uart5),
+ FUNCTION(qdss_traceclk_a),
+ FUNCTION(m_voc),
+ FUNCTION(blsp_i2c5),
+ FUNCTION(qdss_tracectl_a),
+ FUNCTION(qdss_tracedata_a),
+ FUNCTION(blsp_spi6),
+ FUNCTION(blsp_uart6),
+ FUNCTION(qdss_tracectl_b),
+ FUNCTION(blsp_i2c6),
+ FUNCTION(qdss_traceclk_b),
+ FUNCTION(mdp_vsync),
+ FUNCTION(pri_mi2s_mclk_a),
+ FUNCTION(sec_mi2s_mclk_a),
+ FUNCTION(cam_mclk),
+ FUNCTION(cci0_i2c),
+ FUNCTION(cci1_i2c),
+ FUNCTION(blsp1_spi),
+ FUNCTION(blsp3_spi),
+ FUNCTION(gcc_gp1_clk_a),
+ FUNCTION(gcc_gp2_clk_a),
+ FUNCTION(gcc_gp3_clk_a),
+ FUNCTION(uim_batt),
+ FUNCTION(sd_write),
+ FUNCTION(uim1_data),
+ FUNCTION(uim1_clk),
+ FUNCTION(uim1_reset),
+ FUNCTION(uim1_present),
+ FUNCTION(uim2_data),
+ FUNCTION(uim2_clk),
+ FUNCTION(uim2_reset),
+ FUNCTION(uim2_present),
+ FUNCTION(ts_xvdd),
+ FUNCTION(mipi_dsi0),
+ FUNCTION(us_euro),
+ FUNCTION(ts_resout),
+ FUNCTION(ts_sample),
+ FUNCTION(sec_mi2s_mclk_b),
+ FUNCTION(pri_mi2s),
+ FUNCTION(codec_reset),
+ FUNCTION(cdc_pdm0),
+ FUNCTION(us_emitter),
+ FUNCTION(pri_mi2s_mclk_b),
+ FUNCTION(pri_mi2s_mclk_c),
+ FUNCTION(lpass_slimbus),
+ FUNCTION(lpass_slimbus0),
+ FUNCTION(lpass_slimbus1),
+ FUNCTION(codec_int1),
+ FUNCTION(codec_int2),
+ FUNCTION(wcss_bt),
+ FUNCTION(sdc3),
+ FUNCTION(wcss_wlan2),
+ FUNCTION(wcss_wlan1),
+ FUNCTION(wcss_wlan0),
+ FUNCTION(wcss_wlan),
+ FUNCTION(wcss_fm),
+ FUNCTION(key_volp),
+ FUNCTION(key_snapshot),
+ FUNCTION(key_focus),
+ FUNCTION(key_home),
+ FUNCTION(pwr_down),
+ FUNCTION(dmic0_clk),
+ FUNCTION(hdmi_int),
+ FUNCTION(dmic0_data),
+ FUNCTION(wsa_vi),
+ FUNCTION(wsa_en),
+ FUNCTION(blsp_spi8),
+ FUNCTION(wsa_irq),
+ FUNCTION(blsp_i2c8),
+ FUNCTION(pa_indicator),
+ FUNCTION(modem_tsync),
+ FUNCTION(ssbi_wtr1),
+ FUNCTION(gsm1_tx),
+ FUNCTION(gsm0_tx),
+ FUNCTION(sdcard_det),
+ FUNCTION(sec_mi2s),
+ FUNCTION(ss_switch),
+};
+
+static const struct msm_pingroup msm8976_groups[] = {
+ PINGROUP(0, blsp_spi1, blsp_uart1, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(1, blsp_spi1, blsp_uart1, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(2, blsp_spi1, blsp_uart1, blsp_i2c1, NA, NA, NA, NA, NA, NA),
+ PINGROUP(3, blsp_spi1, blsp_uart1, blsp_i2c1, NA, NA, NA, NA, NA, NA),
+ PINGROUP(4, blsp_spi2, blsp_uart2, NA, NA, NA, qdss_tracectl_b, NA, NA, NA),
+ PINGROUP(5, blsp_spi2, blsp_uart2, NA, NA, NA, qdss_traceclk_b, NA, NA, NA),
+ PINGROUP(6, blsp_spi2, blsp_uart2, blsp_i2c2, NA, NA, NA, NA, NA, NA),
+ PINGROUP(7, blsp_spi2, blsp_uart2, blsp_i2c2, NA, NA, NA, NA, NA, NA),
+ PINGROUP(8, blsp_spi3, NA, NA, NA, NA, qdss_tracedata_a, NA, NA, NA),
+ PINGROUP(9, blsp_spi3, NA, NA, NA, qdss_tracedata_a, NA, NA, NA, NA),
+ PINGROUP(10, blsp_spi3, NA, blsp_i2c3, NA, NA, qdss_tracedata_a, NA, NA, NA),
+ PINGROUP(11, blsp_spi3, NA, blsp_i2c3, NA, NA, NA, NA, NA, NA),
+ PINGROUP(12, blsp_spi4, NA, gcc_gp2_clk_b, NA, NA, NA, NA, NA, NA),
+ PINGROUP(13, blsp_spi4, NA, gcc_gp3_clk_b, NA, NA, NA, NA, NA, NA),
+ PINGROUP(14, blsp_spi4, NA, blsp_i2c4, NA, NA, NA, NA, NA, NA),
+ PINGROUP(15, blsp_spi4, NA, blsp_i2c4, NA, NA, NA, NA, NA, NA),
+ PINGROUP(16, blsp_spi8, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(17, blsp_spi8, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(18, blsp_spi8, NA, blsp_i2c8, NA, NA, NA, NA, NA, NA),
+ PINGROUP(19, blsp_spi8, NA, blsp_i2c8, NA, NA, NA, NA, NA, NA),
+ PINGROUP(20, blsp_spi6, blsp_uart6, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(21, blsp_spi6, blsp_uart6, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(22, blsp_spi6, blsp_uart6, blsp_i2c6, NA, NA, NA, NA, NA, NA),
+ PINGROUP(23, blsp_spi6, blsp_uart6, blsp_i2c6, NA, NA, NA, NA, NA, NA),
+ PINGROUP(24, mdp_vsync, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(25, mdp_vsync, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(26, cam_mclk, NA, NA, NA, NA, qdss_tracedata_b, NA, NA, NA),
+ PINGROUP(27, cam_mclk, NA, NA, NA, NA, NA, qdss_tracedata_b, NA, NA),
+ PINGROUP(28, cam_mclk, NA, NA, NA, NA, qdss_tracedata_b, NA, NA, NA),
+ PINGROUP(29, cci0_i2c, NA, NA, NA, NA, qdss_tracedata_b, NA, NA, NA),
+ PINGROUP(30, cci0_i2c, NA, NA, NA, NA, NA, qdss_tracedata_b, NA, NA),
+ PINGROUP(31, NA, NA, NA, NA, NA, NA, NA, qdss_tracedata_b, NA),
+ PINGROUP(32, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(33, NA, NA, NA, NA, NA, NA, qdss_tracedata_b, NA, NA),
+ PINGROUP(34, NA, NA, NA, NA, NA, NA, NA, NA, qdss_tracedata_b),
+ PINGROUP(35, NA, NA, NA, NA, NA, NA, NA, NA, qdss_tracedata_b),
+ PINGROUP(36, NA, NA, NA, NA, NA, NA, qdss_tracedata_b, NA, NA),
+ PINGROUP(37, NA, NA, NA, qdss_tracedata_b, NA, NA, NA, NA, NA),
+ PINGROUP(38, NA, NA, NA, NA, NA, NA, NA, qdss_tracedata_b, NA),
+ PINGROUP(39, wcss_bt, sdc3, NA, qdss_tracedata_a, NA, NA, NA, NA, NA),
+ PINGROUP(40, wcss_wlan, sdc3, NA, qdss_tracedata_a, NA, NA, NA, NA, NA),
+ PINGROUP(41, wcss_wlan, sdc3, NA, qdss_tracedata_a, NA, NA, NA, NA, NA),
+ PINGROUP(42, wcss_wlan, sdc3, NA, qdss_tracedata_a, NA, NA, NA, NA, NA),
+ PINGROUP(43, wcss_wlan, sdc3, NA, NA, qdss_tracedata_a, NA, NA, NA, NA),
+ PINGROUP(44, wcss_wlan, sdc3, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(45, wcss_fm, NA, qdss_tracectl_a, NA, NA, NA, NA, NA, NA),
+ PINGROUP(46, wcss_fm, NA, NA, qdss_traceclk_a, NA, NA, NA, NA, NA),
+ PINGROUP(47, wcss_bt, NA, qdss_tracedata_a, NA, NA, NA, NA, NA, NA),
+ PINGROUP(48, wcss_bt, NA, qdss_tracedata_a, NA, NA, NA, NA, NA, NA),
+ PINGROUP(49, NA, NA, gcc_gp1_clk_a, NA, NA, NA, NA, NA, NA),
+ PINGROUP(50, NA, sd_write, gcc_gp2_clk_a, NA, NA, NA, NA, NA, NA),
+ PINGROUP(51, uim2_data, gcc_gp3_clk_a, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(52, uim2_clk, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(53, uim2_reset, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(54, uim2_present, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(55, uim1_data, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(56, uim1_clk, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(57, uim1_reset, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(58, uim1_present, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(59, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(60, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(61, uim_batt, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(62, sec_mi2s_mclk_a, pri_mi2s_mclk_b, qdss_tracedata_a, NA, NA, NA, NA, NA, NA),
+ PINGROUP(63, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(64, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(65, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(66, dmic0_clk, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(67, dmic0_data, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(68, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(69, qdss_tracedata_a, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(70, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(71, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(72, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(73, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(74, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(75, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(76, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(77, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(78, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(79, NA, ssbi_wtr1, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(80, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(81, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(82, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(83, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(84, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(85, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(86, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(87, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(88, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(89, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(90, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(91, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(92, NA, NA, pa_indicator, NA, NA, NA, NA, NA, NA),
+ PINGROUP(93, NA, modem_tsync, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(94, NA, ssbi_wtr1, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(95, NA, gsm1_tx, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(96, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(97, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(98, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(99, gsm0_tx, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(100, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(101, blsp1_spi, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(102, sec_mi2s, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(103, cci1_i2c, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(104, cci1_i2c, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(105, sec_mi2s, gcc_gp1_clk_b, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(106, blsp3_spi, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(107, blsp3_spi, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(108, wsa_vi, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(109, wsa_vi, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(110, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(111, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(112, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(113, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(114, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(115, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(116, pri_mi2s_mclk_c, cdc_pdm0, NA, NA, NA, qdss_tracedata_b, NA, NA, NA),
+ PINGROUP(117, lpass_slimbus, cdc_pdm0, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(118, lpass_slimbus0, cdc_pdm0, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(119, lpass_slimbus1, cdc_pdm0, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(120, cdc_pdm0, NA, NA, NA, NA, NA, NA, qdss_tracedata_a, NA),
+ PINGROUP(121, cdc_pdm0, NA, NA, NA, NA, NA, NA, qdss_tracedata_a, NA),
+ PINGROUP(122, pri_mi2s, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(123, pri_mi2s, m_voc, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(124, pri_mi2s, m_voc, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(125, pri_mi2s, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(126, pri_mi2s_mclk_a, sec_mi2s_mclk_b, NA, NA, NA, NA, NA, NA, qdss_tracedata_b),
+ PINGROUP(127, pri_mi2s, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(128, NA, NA, NA, NA, NA, NA, qdss_tracedata_b, NA, NA),
+ PINGROUP(129, qdss_tracedata_b, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(130, qdss_tracedata_a, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(131, qdss_tracedata_a, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(132, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(133, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(134, blsp_spi5, blsp_uart5, sec_mi2s, NA, NA, NA, NA, NA, NA),
+ PINGROUP(135, blsp_spi5, blsp_uart5, sec_mi2s, NA, NA, NA, NA, NA, NA),
+ PINGROUP(136, blsp_spi5, blsp_uart5, blsp_i2c5, NA, NA, NA, NA, NA, NA),
+ PINGROUP(137, blsp_spi5, blsp_uart5, blsp_i2c5, NA, NA, NA, NA, NA, NA),
+ PINGROUP(138, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(139, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(140, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(141, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(142, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(143, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ PINGROUP(144, NA, NA, NA, NA, NA, NA, NA, NA, NA),
+ SDC_QDSD_PINGROUP(sdc1_clk, 0x10a000, 13, 6),
+ SDC_QDSD_PINGROUP(sdc1_cmd, 0x10a000, 11, 3),
+ SDC_QDSD_PINGROUP(sdc1_data, 0x10a000, 9, 0),
+ SDC_QDSD_PINGROUP(sdc1_rclk, 0x10a000, 15, 0),
+ SDC_QDSD_PINGROUP(sdc2_clk, 0x109000, 14, 6),
+ SDC_QDSD_PINGROUP(sdc2_cmd, 0x109000, 11, 3),
+ SDC_QDSD_PINGROUP(sdc2_data, 0x109000, 9, 0),
+ SDC_QDSD_PINGROUP(qdsd_clk, 0x19c000, 3, 0),
+ SDC_QDSD_PINGROUP(qdsd_cmd, 0x19c000, 8, 5),
+ SDC_QDSD_PINGROUP(qdsd_data0, 0x19c000, 13, 10),
+ SDC_QDSD_PINGROUP(qdsd_data1, 0x19c000, 18, 15),
+ SDC_QDSD_PINGROUP(qdsd_data2, 0x19c000, 23, 20),
+ SDC_QDSD_PINGROUP(qdsd_data3, 0x19c000, 28, 25),
+};
+
+static const struct msm_pinctrl_soc_data msm8976_pinctrl = {
+ .pins = msm8976_pins,
+ .npins = ARRAY_SIZE(msm8976_pins),
+ .functions = msm8976_functions,
+ .nfunctions = ARRAY_SIZE(msm8976_functions),
+ .groups = msm8976_groups,
+ .ngroups = ARRAY_SIZE(msm8976_groups),
+ .ngpios = 145,
+};
+
+static int msm8976_pinctrl_probe(struct platform_device *pdev)
+{
+ return msm_pinctrl_probe(pdev, &msm8976_pinctrl);
+}
+
+static const struct of_device_id msm8976_pinctrl_of_match[] = {
+ { .compatible = "qcom,msm8976-pinctrl", },
+ { },
+};
+
+static struct platform_driver msm8976_pinctrl_driver = {
+ .driver = {
+ .name = "msm8976-pinctrl",
+ .owner = THIS_MODULE,
+ .of_match_table = msm8976_pinctrl_of_match,
+ },
+ .probe = msm8976_pinctrl_probe,
+ .remove = msm_pinctrl_remove,
+};
+
+static int __init msm8976_pinctrl_init(void)
+{
+ return platform_driver_register(&msm8976_pinctrl_driver);
+}
+arch_initcall(msm8976_pinctrl_init);
+
+static void __exit msm8976_pinctrl_exit(void)
+{
+ platform_driver_unregister(&msm8976_pinctrl_driver);
+}
+module_exit(msm8976_pinctrl_exit);
+
+MODULE_DESCRIPTION("Qualcomm msm8976 pinctrl driver");
+MODULE_LICENSE("GPL v2");
+MODULE_DEVICE_TABLE(of, msm8976_pinctrl_of_match);
--
2.21.0
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 3/5] soc: qcom: smd-rpm: Add MSM8976 compatible
2019-09-21 10:12 [PATCH 0/5] Add core MSM8956/76 SoC support drivers kholk11
2019-09-21 10:12 ` [PATCH 1/5] pinctrl: qcom: Add a pinctrl driver for MSM8976 and 8956 kholk11
@ 2019-09-21 10:12 ` kholk11
2019-10-05 4:23 ` Bjorn Andersson
2019-09-21 10:12 ` [PATCH 4/5] dt-bindings: power: Add missing rpmpd smd performance level kholk11
2019-09-21 10:12 ` [PATCH 5/5] soc: qcom: rpmpd: Add rpm power domains for msm8956 kholk11
3 siblings, 1 reply; 12+ messages in thread
From: kholk11 @ 2019-09-21 10:12 UTC (permalink / raw)
To: linux-arm-msm
Cc: kholk11, marijns95, agross, mturquette, sboyd, robh+dt,
mark.rutland, bjorn.andersson, linus.walleij, linux-clk,
linux-gpio
From: "Angelo G. Del Regno" <kholk11@gmail.com>
Add a compatible for the RPM on the Qualcomm MSM8976 platform:
this is also valid for MSM8956 and their APQ variants.
Signed-off-by: Angelo G. Del Regno <kholk11@gmail.com>
---
Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt | 1 +
drivers/soc/qcom/smd-rpm.c | 1 +
2 files changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt
index f3fa313963d5..616fddcd09fd 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt
@@ -22,6 +22,7 @@ resources.
"qcom,rpm-apq8084"
"qcom,rpm-msm8916"
"qcom,rpm-msm8974"
+ "qcom,rpm-msm8976"
"qcom,rpm-msm8998"
"qcom,rpm-sdm660"
"qcom,rpm-qcs404"
diff --git a/drivers/soc/qcom/smd-rpm.c b/drivers/soc/qcom/smd-rpm.c
index fa9dd12b5e39..fe2199f6ce8f 100644
--- a/drivers/soc/qcom/smd-rpm.c
+++ b/drivers/soc/qcom/smd-rpm.c
@@ -217,6 +217,7 @@ static const struct of_device_id qcom_smd_rpm_of_match[] = {
{ .compatible = "qcom,rpm-apq8084" },
{ .compatible = "qcom,rpm-msm8916" },
{ .compatible = "qcom,rpm-msm8974" },
+ { .compatible = "qcom,rpm-msm8976" },
{ .compatible = "qcom,rpm-msm8996" },
{ .compatible = "qcom,rpm-msm8998" },
{ .compatible = "qcom,rpm-sdm660" },
--
2.21.0
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 4/5] dt-bindings: power: Add missing rpmpd smd performance level
2019-09-21 10:12 [PATCH 0/5] Add core MSM8956/76 SoC support drivers kholk11
2019-09-21 10:12 ` [PATCH 1/5] pinctrl: qcom: Add a pinctrl driver for MSM8976 and 8956 kholk11
2019-09-21 10:12 ` [PATCH 3/5] soc: qcom: smd-rpm: Add MSM8976 compatible kholk11
@ 2019-09-21 10:12 ` kholk11
2019-10-05 4:27 ` Bjorn Andersson
2019-09-21 10:12 ` [PATCH 5/5] soc: qcom: rpmpd: Add rpm power domains for msm8956 kholk11
3 siblings, 1 reply; 12+ messages in thread
From: kholk11 @ 2019-09-21 10:12 UTC (permalink / raw)
To: linux-arm-msm
Cc: kholk11, marijns95, agross, mturquette, sboyd, robh+dt,
mark.rutland, bjorn.andersson, linus.walleij, linux-clk,
linux-gpio
From: "Angelo G. Del Regno" <kholk11@gmail.com>
The RPM_SMD_LEVEL_TURBO_HIGH is used by MSM8956/8976 and APQ variants:
add the definition.
Signed-off-by: Angelo G. Del Regno <kholk11@gmail.com>
---
include/dt-bindings/power/qcom-rpmpd.h | 1 +
1 file changed, 1 insertion(+)
diff --git a/include/dt-bindings/power/qcom-rpmpd.h b/include/dt-bindings/power/qcom-rpmpd.h
index 93e36d011527..30a0aee0df57 100644
--- a/include/dt-bindings/power/qcom-rpmpd.h
+++ b/include/dt-bindings/power/qcom-rpmpd.h
@@ -68,6 +68,7 @@
#define RPM_SMD_LEVEL_NOM_PLUS 320
#define RPM_SMD_LEVEL_TURBO 384
#define RPM_SMD_LEVEL_TURBO_NO_CPR 416
+#define RPM_SMD_LEVEL_TURBO_HIGH 448
#define RPM_SMD_LEVEL_BINNING 512
#endif
--
2.21.0
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 5/5] soc: qcom: rpmpd: Add rpm power domains for msm8956
2019-09-21 10:12 [PATCH 0/5] Add core MSM8956/76 SoC support drivers kholk11
` (2 preceding siblings ...)
2019-09-21 10:12 ` [PATCH 4/5] dt-bindings: power: Add missing rpmpd smd performance level kholk11
@ 2019-09-21 10:12 ` kholk11
2019-10-05 4:25 ` Bjorn Andersson
3 siblings, 1 reply; 12+ messages in thread
From: kholk11 @ 2019-09-21 10:12 UTC (permalink / raw)
To: linux-arm-msm
Cc: kholk11, marijns95, agross, mturquette, sboyd, robh+dt,
mark.rutland, bjorn.andersson, linus.walleij, linux-clk,
linux-gpio
From: "Angelo G. Del Regno" <kholk11@gmail.com>
The MSM8956 SoC has two main voltage-level power domains, VDD_CX
and VDD_MX, which also have their own voltage-floor-level (VFL)
corner.
Signed-off-by: Angelo G. Del Regno <kholk11@gmail.com>
---
.../devicetree/bindings/power/qcom,rpmpd.txt | 1 +
drivers/soc/qcom/rpmpd.c | 23 +++++++++++++++++++
include/dt-bindings/power/qcom-rpmpd.h | 8 +++++++
3 files changed, 32 insertions(+)
diff --git a/Documentation/devicetree/bindings/power/qcom,rpmpd.txt b/Documentation/devicetree/bindings/power/qcom,rpmpd.txt
index eb35b22f9e23..30176b1e595a 100644
--- a/Documentation/devicetree/bindings/power/qcom,rpmpd.txt
+++ b/Documentation/devicetree/bindings/power/qcom,rpmpd.txt
@@ -5,6 +5,7 @@ which then translates it into a corresponding voltage on a rail
Required Properties:
- compatible: Should be one of the following
+ * qcom,msm8956-rpmpd: RPM Power domain for the msm8956 family of SoC
* qcom,msm8996-rpmpd: RPM Power domain for the msm8996 family of SoC
* qcom,msm8998-rpmpd: RPM Power domain for the msm8998 family of SoC
* qcom,qcs404-rpmpd: RPM Power domain for the qcs404 family of SoC
diff --git a/drivers/soc/qcom/rpmpd.c b/drivers/soc/qcom/rpmpd.c
index 3c1a55cf25d6..b50f62851461 100644
--- a/drivers/soc/qcom/rpmpd.c
+++ b/drivers/soc/qcom/rpmpd.c
@@ -115,6 +115,28 @@ struct rpmpd_desc {
static DEFINE_MUTEX(rpmpd_lock);
+/* msm8956 RPM Power Domains */
+DEFINE_RPMPD_PAIR(msm8956, vddcx, vddcx_ao, SMPA, LEVEL, 2);
+DEFINE_RPMPD_PAIR(msm8956, vddmx, vddmx_ao, SMPA, LEVEL, 6);
+
+DEFINE_RPMPD_VFL(msm8956, vddcx_vfl, RWSC, 2);
+DEFINE_RPMPD_VFL(msm8956, vddmx_vfl, RWSM, 6);
+
+static struct rpmpd *msm8956_rpmpds[] = {
+ [MSM8956_VDDCX] = &msm8956_vddcx,
+ [MSM8956_VDDCX_AO] = &msm8956_vddcx_ao,
+ [MSM8956_VDDCX_VFL] = &msm8956_vddcx_vfl,
+ [MSM8956_VDDMX] = &msm8956_vddmx,
+ [MSM8956_VDDMX_AO] = &msm8956_vddmx_ao,
+ [MSM8956_VDDMX_VFL] = &msm8956_vddmx_vfl,
+};
+
+static const struct rpmpd_desc msm8956_desc = {
+ .rpmpds = msm8956_rpmpds,
+ .num_pds = ARRAY_SIZE(msm8956_rpmpds),
+ .max_state = RPM_SMD_LEVEL_TURBO_HIGH,
+};
+
/* msm8996 RPM Power domains */
DEFINE_RPMPD_PAIR(msm8996, vddcx, vddcx_ao, SMPA, CORNER, 1);
DEFINE_RPMPD_PAIR(msm8996, vddmx, vddmx_ao, SMPA, CORNER, 2);
@@ -198,6 +220,7 @@ static const struct rpmpd_desc qcs404_desc = {
};
static const struct of_device_id rpmpd_match_table[] = {
+ { .compatible = "qcom,msm8956-rpmpd", .data = &msm8956_desc },
{ .compatible = "qcom,msm8996-rpmpd", .data = &msm8996_desc },
{ .compatible = "qcom,msm8998-rpmpd", .data = &msm8998_desc },
{ .compatible = "qcom,qcs404-rpmpd", .data = &qcs404_desc },
diff --git a/include/dt-bindings/power/qcom-rpmpd.h b/include/dt-bindings/power/qcom-rpmpd.h
index 30a0aee0df57..3423f964c233 100644
--- a/include/dt-bindings/power/qcom-rpmpd.h
+++ b/include/dt-bindings/power/qcom-rpmpd.h
@@ -27,6 +27,14 @@
#define RPMH_REGULATOR_LEVEL_TURBO 384
#define RPMH_REGULATOR_LEVEL_TURBO_L1 416
+/* MSM8956 Power Domain Indexes */
+#define MSM8956_VDDCX 0
+#define MSM8956_VDDCX_AO 1
+#define MSM8956_VDDCX_VFL 2
+#define MSM8956_VDDMX 3
+#define MSM8956_VDDMX_AO 4
+#define MSM8956_VDDMX_VFL 5
+
/* MSM8996 Power Domain Indexes */
#define MSM8996_VDDCX 0
#define MSM8996_VDDCX_AO 1
--
2.21.0
^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH 1/5] pinctrl: qcom: Add a pinctrl driver for MSM8976 and 8956
2019-09-21 10:12 ` [PATCH 1/5] pinctrl: qcom: Add a pinctrl driver for MSM8976 and 8956 kholk11
@ 2019-10-04 21:16 ` Linus Walleij
2019-10-05 3:59 ` Bjorn Andersson
1 sibling, 0 replies; 12+ messages in thread
From: Linus Walleij @ 2019-10-04 21:16 UTC (permalink / raw)
To: kholk11
Cc: MSM, marijns95, Andy Gross, Michael Turquette, Stephen Boyd,
Rob Herring, Mark Rutland, Bjorn Andersson, linux-clk,
open list:GPIO SUBSYSTEM
Hi Angelo!
Thanks for your patch!
On Sat, Sep 21, 2019 at 12:12 PM <kholk11@gmail.com> wrote:
> From: "Angelo G. Del Regno" <kholk11@gmail.com>
>
> Add the pinctrl driver to support pin configuration with the
> pinctrl framework on MSM8976, MSM8956, APQ8056, APQ8076.
>
> Signed-off-by: Angelo G. Del Regno <kholk11@gmail.com>
This changes device tree bindings so you need to Cc devicetree@vger.kernel.org.
Usually they want the device tree changes in a separate patch.
It'd be great if I can apply the pinctrl patches separately from the rest of
the series.
Also I need Bjorn's review on it first.
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 1/5] pinctrl: qcom: Add a pinctrl driver for MSM8976 and 8956
2019-09-21 10:12 ` [PATCH 1/5] pinctrl: qcom: Add a pinctrl driver for MSM8976 and 8956 kholk11
2019-10-04 21:16 ` Linus Walleij
@ 2019-10-05 3:59 ` Bjorn Andersson
2019-10-05 9:19 ` AngeloGioacchino Del Regno
1 sibling, 1 reply; 12+ messages in thread
From: Bjorn Andersson @ 2019-10-05 3:59 UTC (permalink / raw)
To: kholk11
Cc: linux-arm-msm, marijns95, agross, mturquette, sboyd, robh+dt,
mark.rutland, linus.walleij, linux-clk, linux-gpio
On Sat 21 Sep 03:12 PDT 2019, kholk11@gmail.com wrote:
> From: "Angelo G. Del Regno" <kholk11@gmail.com>
>
> Add the pinctrl driver to support pin configuration with the
> pinctrl framework on MSM8976, MSM8956, APQ8056, APQ8076.
>
> Signed-off-by: Angelo G. Del Regno <kholk11@gmail.com>
> ---
> .../bindings/pinctrl/qcom,msm8976-pinctrl.txt | 183 +++
> drivers/pinctrl/qcom/Kconfig | 10 +
> drivers/pinctrl/qcom/Makefile | 1 +
> drivers/pinctrl/qcom/pinctrl-msm8976.c | 1128 +++++++++++++++++
> 4 files changed, 1322 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
> create mode 100644 drivers/pinctrl/qcom/pinctrl-msm8976.c
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
> new file mode 100644
> index 000000000000..4e944f84b7d7
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
> @@ -0,0 +1,183 @@
> +Qualcomm MSM8976 TLMM block
As Linus indicated, please send your the DT bindings in separate
patches.
> +
[..]
> +Example:
> +
> + tlmm: pinctrl@1000000 {
> + compatible = "qcom,msm8976-pinctrl";
> + reg = <0x1000000 0x300000>;
> + interrupts = <0 208 0>;
<GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&tlmm 0 0 145>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + blsp1_uart2_active: blsp1_uart2_active {
> + mux {
> + pins = "gpio4", "gpio5", "gpio6", "gpio7";
> + function = "blsp_uart2";
> + };
> +
> + config {
> + pins = "gpio4", "gpio5", "gpio6", "gpio7";
> + drive-strength = <2>;
> + bias-disable;
> + };
> + };
> + };
> diff --git a/drivers/pinctrl/qcom/Kconfig b/drivers/pinctrl/qcom/Kconfig
[..]
> +static struct platform_driver msm8976_pinctrl_driver = {
> + .driver = {
> + .name = "msm8976-pinctrl",
> + .owner = THIS_MODULE,
No need to specify .onwer on platform_drivers anymore.
Apart from that, I think this patch looks good.
Regards,
Bjorn
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 3/5] soc: qcom: smd-rpm: Add MSM8976 compatible
2019-09-21 10:12 ` [PATCH 3/5] soc: qcom: smd-rpm: Add MSM8976 compatible kholk11
@ 2019-10-05 4:23 ` Bjorn Andersson
0 siblings, 0 replies; 12+ messages in thread
From: Bjorn Andersson @ 2019-10-05 4:23 UTC (permalink / raw)
To: kholk11
Cc: linux-arm-msm, marijns95, agross, mturquette, sboyd, robh+dt,
mark.rutland, linus.walleij, linux-clk, linux-gpio
On Sat 21 Sep 03:12 PDT 2019, kholk11@gmail.com wrote:
> From: "Angelo G. Del Regno" <kholk11@gmail.com>
>
> Add a compatible for the RPM on the Qualcomm MSM8976 platform:
> this is also valid for MSM8956 and their APQ variants.
>
> Signed-off-by: Angelo G. Del Regno <kholk11@gmail.com>
Applied
Thanks,
Bjorn
> ---
> Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt | 1 +
> drivers/soc/qcom/smd-rpm.c | 1 +
> 2 files changed, 2 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt
> index f3fa313963d5..616fddcd09fd 100644
> --- a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt
> +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt
> @@ -22,6 +22,7 @@ resources.
> "qcom,rpm-apq8084"
> "qcom,rpm-msm8916"
> "qcom,rpm-msm8974"
> + "qcom,rpm-msm8976"
> "qcom,rpm-msm8998"
> "qcom,rpm-sdm660"
> "qcom,rpm-qcs404"
> diff --git a/drivers/soc/qcom/smd-rpm.c b/drivers/soc/qcom/smd-rpm.c
> index fa9dd12b5e39..fe2199f6ce8f 100644
> --- a/drivers/soc/qcom/smd-rpm.c
> +++ b/drivers/soc/qcom/smd-rpm.c
> @@ -217,6 +217,7 @@ static const struct of_device_id qcom_smd_rpm_of_match[] = {
> { .compatible = "qcom,rpm-apq8084" },
> { .compatible = "qcom,rpm-msm8916" },
> { .compatible = "qcom,rpm-msm8974" },
> + { .compatible = "qcom,rpm-msm8976" },
> { .compatible = "qcom,rpm-msm8996" },
> { .compatible = "qcom,rpm-msm8998" },
> { .compatible = "qcom,rpm-sdm660" },
> --
> 2.21.0
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 5/5] soc: qcom: rpmpd: Add rpm power domains for msm8956
2019-09-21 10:12 ` [PATCH 5/5] soc: qcom: rpmpd: Add rpm power domains for msm8956 kholk11
@ 2019-10-05 4:25 ` Bjorn Andersson
2019-10-05 9:23 ` AngeloGioacchino Del Regno
0 siblings, 1 reply; 12+ messages in thread
From: Bjorn Andersson @ 2019-10-05 4:25 UTC (permalink / raw)
To: kholk11
Cc: linux-arm-msm, marijns95, agross, mturquette, sboyd, robh+dt,
mark.rutland, linus.walleij, linux-clk, linux-gpio
On Sat 21 Sep 03:12 PDT 2019, kholk11@gmail.com wrote:
> From: "Angelo G. Del Regno" <kholk11@gmail.com>
>
> The MSM8956 SoC has two main voltage-level power domains, VDD_CX
> and VDD_MX, which also have their own voltage-floor-level (VFL)
> corner.
>
> Signed-off-by: Angelo G. Del Regno <kholk11@gmail.com>
I was under the impression that 8956/76 can be used interchangeably, if
so I would prefer if you pick one (8976 as that seems to be your common
choice) and stick with that.
If not, I think it would be nice if all bindings came with both
compatibles.
Regards,
Bjorn
> ---
> .../devicetree/bindings/power/qcom,rpmpd.txt | 1 +
> drivers/soc/qcom/rpmpd.c | 23 +++++++++++++++++++
> include/dt-bindings/power/qcom-rpmpd.h | 8 +++++++
> 3 files changed, 32 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/power/qcom,rpmpd.txt b/Documentation/devicetree/bindings/power/qcom,rpmpd.txt
> index eb35b22f9e23..30176b1e595a 100644
> --- a/Documentation/devicetree/bindings/power/qcom,rpmpd.txt
> +++ b/Documentation/devicetree/bindings/power/qcom,rpmpd.txt
> @@ -5,6 +5,7 @@ which then translates it into a corresponding voltage on a rail
>
> Required Properties:
> - compatible: Should be one of the following
> + * qcom,msm8956-rpmpd: RPM Power domain for the msm8956 family of SoC
> * qcom,msm8996-rpmpd: RPM Power domain for the msm8996 family of SoC
> * qcom,msm8998-rpmpd: RPM Power domain for the msm8998 family of SoC
> * qcom,qcs404-rpmpd: RPM Power domain for the qcs404 family of SoC
> diff --git a/drivers/soc/qcom/rpmpd.c b/drivers/soc/qcom/rpmpd.c
> index 3c1a55cf25d6..b50f62851461 100644
> --- a/drivers/soc/qcom/rpmpd.c
> +++ b/drivers/soc/qcom/rpmpd.c
> @@ -115,6 +115,28 @@ struct rpmpd_desc {
>
> static DEFINE_MUTEX(rpmpd_lock);
>
> +/* msm8956 RPM Power Domains */
> +DEFINE_RPMPD_PAIR(msm8956, vddcx, vddcx_ao, SMPA, LEVEL, 2);
> +DEFINE_RPMPD_PAIR(msm8956, vddmx, vddmx_ao, SMPA, LEVEL, 6);
> +
> +DEFINE_RPMPD_VFL(msm8956, vddcx_vfl, RWSC, 2);
> +DEFINE_RPMPD_VFL(msm8956, vddmx_vfl, RWSM, 6);
> +
> +static struct rpmpd *msm8956_rpmpds[] = {
> + [MSM8956_VDDCX] = &msm8956_vddcx,
> + [MSM8956_VDDCX_AO] = &msm8956_vddcx_ao,
> + [MSM8956_VDDCX_VFL] = &msm8956_vddcx_vfl,
> + [MSM8956_VDDMX] = &msm8956_vddmx,
> + [MSM8956_VDDMX_AO] = &msm8956_vddmx_ao,
> + [MSM8956_VDDMX_VFL] = &msm8956_vddmx_vfl,
> +};
> +
> +static const struct rpmpd_desc msm8956_desc = {
> + .rpmpds = msm8956_rpmpds,
> + .num_pds = ARRAY_SIZE(msm8956_rpmpds),
> + .max_state = RPM_SMD_LEVEL_TURBO_HIGH,
> +};
> +
> /* msm8996 RPM Power domains */
> DEFINE_RPMPD_PAIR(msm8996, vddcx, vddcx_ao, SMPA, CORNER, 1);
> DEFINE_RPMPD_PAIR(msm8996, vddmx, vddmx_ao, SMPA, CORNER, 2);
> @@ -198,6 +220,7 @@ static const struct rpmpd_desc qcs404_desc = {
> };
>
> static const struct of_device_id rpmpd_match_table[] = {
> + { .compatible = "qcom,msm8956-rpmpd", .data = &msm8956_desc },
> { .compatible = "qcom,msm8996-rpmpd", .data = &msm8996_desc },
> { .compatible = "qcom,msm8998-rpmpd", .data = &msm8998_desc },
> { .compatible = "qcom,qcs404-rpmpd", .data = &qcs404_desc },
> diff --git a/include/dt-bindings/power/qcom-rpmpd.h b/include/dt-bindings/power/qcom-rpmpd.h
> index 30a0aee0df57..3423f964c233 100644
> --- a/include/dt-bindings/power/qcom-rpmpd.h
> +++ b/include/dt-bindings/power/qcom-rpmpd.h
> @@ -27,6 +27,14 @@
> #define RPMH_REGULATOR_LEVEL_TURBO 384
> #define RPMH_REGULATOR_LEVEL_TURBO_L1 416
>
> +/* MSM8956 Power Domain Indexes */
> +#define MSM8956_VDDCX 0
> +#define MSM8956_VDDCX_AO 1
> +#define MSM8956_VDDCX_VFL 2
> +#define MSM8956_VDDMX 3
> +#define MSM8956_VDDMX_AO 4
> +#define MSM8956_VDDMX_VFL 5
> +
> /* MSM8996 Power Domain Indexes */
> #define MSM8996_VDDCX 0
> #define MSM8996_VDDCX_AO 1
> --
> 2.21.0
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 4/5] dt-bindings: power: Add missing rpmpd smd performance level
2019-09-21 10:12 ` [PATCH 4/5] dt-bindings: power: Add missing rpmpd smd performance level kholk11
@ 2019-10-05 4:27 ` Bjorn Andersson
0 siblings, 0 replies; 12+ messages in thread
From: Bjorn Andersson @ 2019-10-05 4:27 UTC (permalink / raw)
To: kholk11
Cc: linux-arm-msm, marijns95, agross, mturquette, sboyd, robh+dt,
mark.rutland, linus.walleij, linux-clk, linux-gpio
On Sat 21 Sep 03:12 PDT 2019, kholk11@gmail.com wrote:
> From: "Angelo G. Del Regno" <kholk11@gmail.com>
>
> The RPM_SMD_LEVEL_TURBO_HIGH is used by MSM8956/8976 and APQ variants:
> add the definition.
>
> Signed-off-by: Angelo G. Del Regno <kholk11@gmail.com>
Applied
Thanks,
Bjorn
> ---
> include/dt-bindings/power/qcom-rpmpd.h | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/include/dt-bindings/power/qcom-rpmpd.h b/include/dt-bindings/power/qcom-rpmpd.h
> index 93e36d011527..30a0aee0df57 100644
> --- a/include/dt-bindings/power/qcom-rpmpd.h
> +++ b/include/dt-bindings/power/qcom-rpmpd.h
> @@ -68,6 +68,7 @@
> #define RPM_SMD_LEVEL_NOM_PLUS 320
> #define RPM_SMD_LEVEL_TURBO 384
> #define RPM_SMD_LEVEL_TURBO_NO_CPR 416
> +#define RPM_SMD_LEVEL_TURBO_HIGH 448
> #define RPM_SMD_LEVEL_BINNING 512
>
> #endif
> --
> 2.21.0
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 1/5] pinctrl: qcom: Add a pinctrl driver for MSM8976 and 8956
2019-10-05 3:59 ` Bjorn Andersson
@ 2019-10-05 9:19 ` AngeloGioacchino Del Regno
0 siblings, 0 replies; 12+ messages in thread
From: AngeloGioacchino Del Regno @ 2019-10-05 9:19 UTC (permalink / raw)
To: Bjorn Andersson
Cc: MSM, marijns95, agross, Michael Turquette, Stephen Boyd,
Rob Herring, Mark Rutland, Linus Walleij, linux-clk, linux-gpio
Il giorno sab 5 ott 2019 alle ore 05:59 Bjorn Andersson
<bjorn.andersson@linaro.org> ha scritto:
>
> On Sat 21 Sep 03:12 PDT 2019, kholk11@gmail.com wrote:
>
> > From: "Angelo G. Del Regno" <kholk11@gmail.com>
> >
> > Add the pinctrl driver to support pin configuration with the
> > pinctrl framework on MSM8976, MSM8956, APQ8056, APQ8076.
> >
> > Signed-off-by: Angelo G. Del Regno <kholk11@gmail.com>
> > ---
> > .../bindings/pinctrl/qcom,msm8976-pinctrl.txt | 183 +++
> > drivers/pinctrl/qcom/Kconfig | 10 +
> > drivers/pinctrl/qcom/Makefile | 1 +
> > drivers/pinctrl/qcom/pinctrl-msm8976.c | 1128 +++++++++++++++++
> > 4 files changed, 1322 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
> > create mode 100644 drivers/pinctrl/qcom/pinctrl-msm8976.c
> >
> > diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
> > new file mode 100644
> > index 000000000000..4e944f84b7d7
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
> > @@ -0,0 +1,183 @@
> > +Qualcomm MSM8976 TLMM block
>
> As Linus indicated, please send your the DT bindings in separate
> patches.
>
> > +
> [..]
> > +Example:
> > +
> > + tlmm: pinctrl@1000000 {
> > + compatible = "qcom,msm8976-pinctrl";
> > + reg = <0x1000000 0x300000>;
> > + interrupts = <0 208 0>;
>
> <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>
>
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + gpio-ranges = <&tlmm 0 0 145>;
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > +
> > + blsp1_uart2_active: blsp1_uart2_active {
> > + mux {
> > + pins = "gpio4", "gpio5", "gpio6", "gpio7";
> > + function = "blsp_uart2";
> > + };
> > +
> > + config {
> > + pins = "gpio4", "gpio5", "gpio6", "gpio7";
> > + drive-strength = <2>;
> > + bias-disable;
> > + };
> > + };
> > + };
> > diff --git a/drivers/pinctrl/qcom/Kconfig b/drivers/pinctrl/qcom/Kconfig
> [..]
> > +static struct platform_driver msm8976_pinctrl_driver = {
> > + .driver = {
> > + .name = "msm8976-pinctrl",
> > + .owner = THIS_MODULE,
>
> No need to specify .onwer on platform_drivers anymore.
>
>
> Apart from that, I think this patch looks good.
>
> Regards,
> Bjorn
Thanks guys for the review.
Well, I did it in one patch after seeing this practice on other
patches, so I thought to replicate,
despite the well known rule... but yeah, of course, there's absolutely
no problem, I'll send the
two separate patches in a separate series and I'll do the same for the
GCC driver as well,
which doesn't seem that it got sent to the list for some obscure reason.
About the requested changes... sure, I will apply them and resend ASAP.
Thanks again!
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 5/5] soc: qcom: rpmpd: Add rpm power domains for msm8956
2019-10-05 4:25 ` Bjorn Andersson
@ 2019-10-05 9:23 ` AngeloGioacchino Del Regno
0 siblings, 0 replies; 12+ messages in thread
From: AngeloGioacchino Del Regno @ 2019-10-05 9:23 UTC (permalink / raw)
To: Bjorn Andersson
Cc: MSM, marijns95, agross, Michael Turquette, Stephen Boyd,
Rob Herring, Mark Rutland, Linus Walleij, linux-clk, linux-gpio
Il giorno sab 5 ott 2019 alle ore 06:26 Bjorn Andersson
<bjorn.andersson@linaro.org> ha scritto:
>
> On Sat 21 Sep 03:12 PDT 2019, kholk11@gmail.com wrote:
>
> > From: "Angelo G. Del Regno" <kholk11@gmail.com>
> >
> > The MSM8956 SoC has two main voltage-level power domains, VDD_CX
> > and VDD_MX, which also have their own voltage-floor-level (VFL)
> > corner.
> >
> > Signed-off-by: Angelo G. Del Regno <kholk11@gmail.com>
>
> I was under the impression that 8956/76 can be used interchangeably, if
> so I would prefer if you pick one (8976 as that seems to be your common
> choice) and stick with that.
>
> If not, I think it would be nice if all bindings came with both
> compatibles.
>
> Regards,
> Bjorn
>
> > ---
> > .../devicetree/bindings/power/qcom,rpmpd.txt | 1 +
> > drivers/soc/qcom/rpmpd.c | 23 +++++++++++++++++++
> > include/dt-bindings/power/qcom-rpmpd.h | 8 +++++++
> > 3 files changed, 32 insertions(+)
> >
> > diff --git a/Documentation/devicetree/bindings/power/qcom,rpmpd.txt b/Documentation/devicetree/bindings/power/qcom,rpmpd.txt
> > index eb35b22f9e23..30176b1e595a 100644
> > --- a/Documentation/devicetree/bindings/power/qcom,rpmpd.txt
> > +++ b/Documentation/devicetree/bindings/power/qcom,rpmpd.txt
> > @@ -5,6 +5,7 @@ which then translates it into a corresponding voltage on a rail
> >
> > Required Properties:
> > - compatible: Should be one of the following
> > + * qcom,msm8956-rpmpd: RPM Power domain for the msm8956 family of SoC
> > * qcom,msm8996-rpmpd: RPM Power domain for the msm8996 family of SoC
> > * qcom,msm8998-rpmpd: RPM Power domain for the msm8998 family of SoC
> > * qcom,qcs404-rpmpd: RPM Power domain for the qcs404 family of SoC
> > diff --git a/drivers/soc/qcom/rpmpd.c b/drivers/soc/qcom/rpmpd.c
> > index 3c1a55cf25d6..b50f62851461 100644
> > --- a/drivers/soc/qcom/rpmpd.c
> > +++ b/drivers/soc/qcom/rpmpd.c
> > @@ -115,6 +115,28 @@ struct rpmpd_desc {
> >
> > static DEFINE_MUTEX(rpmpd_lock);
> >
> > +/* msm8956 RPM Power Domains */
> > +DEFINE_RPMPD_PAIR(msm8956, vddcx, vddcx_ao, SMPA, LEVEL, 2);
> > +DEFINE_RPMPD_PAIR(msm8956, vddmx, vddmx_ao, SMPA, LEVEL, 6);
> > +
> > +DEFINE_RPMPD_VFL(msm8956, vddcx_vfl, RWSC, 2);
> > +DEFINE_RPMPD_VFL(msm8956, vddmx_vfl, RWSM, 6);
> > +
> > +static struct rpmpd *msm8956_rpmpds[] = {
> > + [MSM8956_VDDCX] = &msm8956_vddcx,
> > + [MSM8956_VDDCX_AO] = &msm8956_vddcx_ao,
> > + [MSM8956_VDDCX_VFL] = &msm8956_vddcx_vfl,
> > + [MSM8956_VDDMX] = &msm8956_vddmx,
> > + [MSM8956_VDDMX_AO] = &msm8956_vddmx_ao,
> > + [MSM8956_VDDMX_VFL] = &msm8956_vddmx_vfl,
> > +};
> > +
> > +static const struct rpmpd_desc msm8956_desc = {
> > + .rpmpds = msm8956_rpmpds,
> > + .num_pds = ARRAY_SIZE(msm8956_rpmpds),
> > + .max_state = RPM_SMD_LEVEL_TURBO_HIGH,
> > +};
> > +
> > /* msm8996 RPM Power domains */
> > DEFINE_RPMPD_PAIR(msm8996, vddcx, vddcx_ao, SMPA, CORNER, 1);
> > DEFINE_RPMPD_PAIR(msm8996, vddmx, vddmx_ao, SMPA, CORNER, 2);
> > @@ -198,6 +220,7 @@ static const struct rpmpd_desc qcs404_desc = {
> > };
> >
> > static const struct of_device_id rpmpd_match_table[] = {
> > + { .compatible = "qcom,msm8956-rpmpd", .data = &msm8956_desc },
> > { .compatible = "qcom,msm8996-rpmpd", .data = &msm8996_desc },
> > { .compatible = "qcom,msm8998-rpmpd", .data = &msm8998_desc },
> > { .compatible = "qcom,qcs404-rpmpd", .data = &qcs404_desc },
> > diff --git a/include/dt-bindings/power/qcom-rpmpd.h b/include/dt-bindings/power/qcom-rpmpd.h
> > index 30a0aee0df57..3423f964c233 100644
> > --- a/include/dt-bindings/power/qcom-rpmpd.h
> > +++ b/include/dt-bindings/power/qcom-rpmpd.h
> > @@ -27,6 +27,14 @@
> > #define RPMH_REGULATOR_LEVEL_TURBO 384
> > #define RPMH_REGULATOR_LEVEL_TURBO_L1 416
> >
> > +/* MSM8956 Power Domain Indexes */
> > +#define MSM8956_VDDCX 0
> > +#define MSM8956_VDDCX_AO 1
> > +#define MSM8956_VDDCX_VFL 2
> > +#define MSM8956_VDDMX 3
> > +#define MSM8956_VDDMX_AO 4
> > +#define MSM8956_VDDMX_VFL 5
> > +
> > /* MSM8996 Power Domain Indexes */
> > #define MSM8996_VDDCX 0
> > #define MSM8996_VDDCX_AO 1
> > --
> > 2.21.0
> >
Yup. My brain stopped working for a minute on that patch :)))
This is applicable to both MSM8956 and MSM8976... and the other drivers that
I've sent are actually reporting a 8976 compatible, so, yes I'll
resend that one as
8976 instead.
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2019-10-05 9:23 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-09-21 10:12 [PATCH 0/5] Add core MSM8956/76 SoC support drivers kholk11
2019-09-21 10:12 ` [PATCH 1/5] pinctrl: qcom: Add a pinctrl driver for MSM8976 and 8956 kholk11
2019-10-04 21:16 ` Linus Walleij
2019-10-05 3:59 ` Bjorn Andersson
2019-10-05 9:19 ` AngeloGioacchino Del Regno
2019-09-21 10:12 ` [PATCH 3/5] soc: qcom: smd-rpm: Add MSM8976 compatible kholk11
2019-10-05 4:23 ` Bjorn Andersson
2019-09-21 10:12 ` [PATCH 4/5] dt-bindings: power: Add missing rpmpd smd performance level kholk11
2019-10-05 4:27 ` Bjorn Andersson
2019-09-21 10:12 ` [PATCH 5/5] soc: qcom: rpmpd: Add rpm power domains for msm8956 kholk11
2019-10-05 4:25 ` Bjorn Andersson
2019-10-05 9:23 ` AngeloGioacchino Del Regno
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).