linux-clk.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Michael Walle <michael@walle.cc>
To: linux-clk@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org
Cc: Michael Turquette <mturquette@baylibre.com>,
	Stephen Boyd <sboyd@kernel.org>, Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>,
	Michael Walle <michael@walle.cc>
Subject: [PATCH 2/2] clk: fsl-sai: new driver
Date: Sat, 23 Nov 2019 00:56:22 +0100	[thread overview]
Message-ID: <20191122235622.8818-2-michael@walle.cc> (raw)
In-Reply-To: <20191122235622.8818-1-michael@walle.cc>

With this driver it is possible to use the BCLK pin of the SAI module as
a generic clock output. This is esp. useful if you want to drive a clock
to an audio codec. Because the output only allows integer divider values
the audio codec needs an integrated PLL.

Signed-off-by: Michael Walle <michael@walle.cc>
---
 drivers/clk/Kconfig       | 12 ++++++
 drivers/clk/Makefile      |  1 +
 drivers/clk/clk-fsl-sai.c | 84 +++++++++++++++++++++++++++++++++++++++
 3 files changed, 97 insertions(+)
 create mode 100644 drivers/clk/clk-fsl-sai.c

diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index c44247d0b83e..d3bd43e8a912 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -167,6 +167,18 @@ config COMMON_CLK_CS2000_CP
 	help
 	  If you say yes here you get support for the CS2000 clock multiplier.
 
+config COMMON_CLK_FSL_SAI
+	bool "Clock driver for BCLK of Freescale SAI cores"
+	depends on ARCH_LAYERSCAPE || COMPILE_TEST
+	help
+	  This driver supports the Freescale SAI (Synchronous Audio Interface)
+	  to be used as a generic clock output. Some SoCs have restrictions
+	  regarding the possible pin multiplexer settings. Eg. on some SoCs
+	  two SAI interfaces can only be enabled together. If just one is
+	  needed, the BCLK pin of the second one can be used as general
+	  purpose clock output. Ideally, it can be used to drive an audio
+	  codec (sometimes known as MCLK).
+
 config COMMON_CLK_GEMINI
 	bool "Clock driver for Cortina Systems Gemini SoC"
 	depends on ARCH_GEMINI || COMPILE_TEST
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index 0138fb14e6f8..139f55e544a8 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -28,6 +28,7 @@ obj-$(CONFIG_ARCH_CLPS711X)		+= clk-clps711x.o
 obj-$(CONFIG_COMMON_CLK_CS2000_CP)	+= clk-cs2000-cp.o
 obj-$(CONFIG_ARCH_EFM32)		+= clk-efm32gg.o
 obj-$(CONFIG_COMMON_CLK_FIXED_MMIO)	+= clk-fixed-mmio.o
+obj-$(CONFIG_COMMON_CLK_FSL_SAI)	+= clk-fsl-sai.o
 obj-$(CONFIG_COMMON_CLK_GEMINI)		+= clk-gemini.o
 obj-$(CONFIG_COMMON_CLK_ASPEED)		+= clk-aspeed.o
 obj-$(CONFIG_MACH_ASPEED_G6)		+= clk-ast2600.o
diff --git a/drivers/clk/clk-fsl-sai.c b/drivers/clk/clk-fsl-sai.c
new file mode 100644
index 000000000000..b92054d15ab1
--- /dev/null
+++ b/drivers/clk/clk-fsl-sai.c
@@ -0,0 +1,84 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Freescale SAI BCLK as a generic clock driver
+ *
+ * Copyright 2019 Kontron Europe GmbH
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/err.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/slab.h>
+
+#define I2S_CSR		0x00
+#define I2S_CR2		0x08
+#define CSR_BCE_BIT	28
+#define CR2_BCD		BIT(24)
+#define CR2_DIV_SHIFT	0
+#define CR2_DIV_WIDTH	8
+
+struct fsl_sai_clk {
+	struct clk_divider div;
+	struct clk_gate gate;
+	spinlock_t lock;
+};
+
+static void __init fsl_sai_clk_setup(struct device_node *node)
+{
+	const char *clk_name = node->name;
+	struct fsl_sai_clk *sai_clk;
+	unsigned int num_parents;
+	const char *parent_name;
+	void __iomem *base;
+	struct clk_hw *hw;
+
+	num_parents = of_clk_get_parent_count(node);
+	if (!num_parents) {
+		pr_err("%s: no parent found", clk_name);
+		return;
+	}
+
+	parent_name = of_clk_get_parent_name(node, 0);
+
+	sai_clk = kzalloc(sizeof(*sai_clk), GFP_KERNEL);
+	if (!sai_clk)
+		return;
+
+	base = of_iomap(node, 0);
+	if (base == NULL) {
+		pr_err("%s: failed to map register space", clk_name);
+		goto err;
+	}
+
+	spin_lock_init(&sai_clk->lock);
+
+	sai_clk->gate.reg = base + I2S_CSR;
+	sai_clk->gate.bit_idx = CSR_BCE_BIT;
+	sai_clk->gate.lock = &sai_clk->lock;
+
+	sai_clk->div.reg = base + I2S_CR2;
+	sai_clk->div.shift = CR2_DIV_SHIFT;
+	sai_clk->div.width = CR2_DIV_WIDTH;
+	sai_clk->div.lock = &sai_clk->lock;
+
+	/* set clock direction, we are the BCLK master */
+	writel(CR2_BCD, base + I2S_CR2);
+
+	hw = clk_hw_register_composite(NULL, clk_name, &parent_name, 1,
+				       NULL, NULL,
+				       &sai_clk->div.hw, &clk_divider_ops,
+				       &sai_clk->gate.hw, &clk_gate_ops,
+				       CLK_SET_RATE_GATE);
+	if (IS_ERR(hw))
+		goto err;
+
+	of_clk_add_hw_provider(node, of_clk_hw_simple_get, hw);
+
+	return;
+
+err:
+	kfree(sai_clk);
+}
+
+CLK_OF_DECLARE(fsl_sai_clk, "fsl,vf610-sai-clock", fsl_sai_clk_setup);
-- 
2.20.1


  reply	other threads:[~2019-11-22 23:56 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-11-22 23:56 [PATCH 1/2] dt-bindings: clock: document the fsl-sai driver Michael Walle
2019-11-22 23:56 ` Michael Walle [this message]
2019-12-02 21:46   ` [PATCH 2/2] clk: fsl-sai: new driver Michael Walle
2019-12-05 15:16 ` [PATCH 1/2] dt-bindings: clock: document the fsl-sai driver Rob Herring
2019-12-06  1:23   ` Michael Walle
2019-12-09 23:36     ` Michael Walle

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20191122235622.8818-2-michael@walle.cc \
    --to=michael@walle.cc \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=mturquette@baylibre.com \
    --cc=robh+dt@kernel.org \
    --cc=sboyd@kernel.org \
    --subject='Re: [PATCH 2/2] clk: fsl-sai: new driver' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).