linux-clk.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Lee Jones <lee.jones@linaro.org>
To: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Cc: mazziesaccount@gmail.com,
	"Jacek Anaszewski" <jacek.anaszewski@gmail.com>,
	"Pavel Machek" <pavel@ucw.cz>, "Dan Murphy" <dmurphy@ti.com>,
	"Rob Herring" <robh+dt@kernel.org>,
	"Mark Rutland" <mark.rutland@arm.com>,
	"Liam Girdwood" <lgirdwood@gmail.com>,
	"Mark Brown" <broonie@kernel.org>,
	"Jonathan Corbet" <corbet@lwn.net>,
	"Michael Turquette" <mturquette@baylibre.com>,
	"Stephen Boyd" <sboyd@kernel.org>,
	"Linus Walleij" <linus.walleij@linaro.org>,
	"Bartosz Golaszewski" <bgolaszewski@baylibre.com>,
	"Alessandro Zummo" <a.zummo@towertech.it>,
	"Alexandre Belloni" <alexandre.belloni@bootlin.com>,
	"Greg Kroah-Hartman" <gregkh@linuxfoundation.org>,
	"Arnd Bergmann" <arnd@arndb.de>,
	"Mauro Carvalho Chehab" <mchehab+samsung@kernel.org>,
	"Wolfram Sang" <wsa+renesas@sang-engineering.com>,
	"Phil Edworthy" <phil.edworthy@renesas.com>,
	"Noralf Trønnes" <noralf@tronnes.org>,
	linux-leds@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-doc@vger.kernel.org,
	linux-clk@vger.kernel.org, linux-gpio@vger.kernel.org,
	linux-rtc@vger.kernel.org
Subject: Re: [PATCH v6 05/15] mfd: bd71828: Support ROHM BD71828 PMIC - core
Date: Mon, 16 Dec 2019 16:46:41 +0000	[thread overview]
Message-ID: <20191216164641.GC18955@dell> (raw)
In-Reply-To: <252de5646fedfec7c575269843a47091fe199c79.1576054779.git.matti.vaittinen@fi.rohmeurope.com>

On Wed, 11 Dec 2019, Matti Vaittinen wrote:

> BD71828GW is a single-chip power management IC for battery-powered portable
> devices. The IC integrates 7 buck converters, 7 LDOs, and a 1500 mA
> single-cell linear charger. Also included is a Coulomb counter, a real-time
> clock (RTC), 3 GPO/regulator control pins, HALL input and a 32.768 kHz
> clock gate.
> 
> Add MFD core driver providing interrupt controller facilities and i2c
> access to sub device drivers.
> 
> Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
> ---
> 
> Changes since v5:
> - No changes
> 
>  drivers/mfd/Kconfig              |  15 ++
>  drivers/mfd/Makefile             |   2 +-
>  drivers/mfd/rohm-bd71828.c       | 319 +++++++++++++++++++++++
>  include/linux/mfd/rohm-bd71828.h | 425 +++++++++++++++++++++++++++++++
>  include/linux/mfd/rohm-generic.h |   1 +
>  5 files changed, 761 insertions(+), 1 deletion(-)
>  create mode 100644 drivers/mfd/rohm-bd71828.c
>  create mode 100644 include/linux/mfd/rohm-bd71828.h

Couple of small nits.  Once fixed, please apply my:

For my own reference:
  Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>

> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 420900852166..c3c9432ef51c 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -1906,6 +1906,21 @@ config MFD_ROHM_BD70528
>  	  10 bits SAR ADC for battery temperature monitor and 1S battery
>  	  charger.
>  
> +config MFD_ROHM_BD71828
> +	tristate "ROHM BD71828 Power Management IC"
> +	depends on I2C=y
> +	depends on OF
> +	select REGMAP_I2C
> +	select REGMAP_IRQ
> +	select MFD_CORE
> +	help
> +	  Select this option to get support for the ROHM BD71828 Power
> +	  Management IC. BD71828GW is a single-chip power management IC for
> +	  battery-powered portable devices. The IC integrates 7 buck
> +	  converters, 7 LDOs, and a 1500 mA single-cell linear charger.
> +	  Also included is a Coulomb counter, a real-time clock (RTC), and
> +	  a 32.768 kHz clock gate.
> +
>  config MFD_STM32_LPTIMER
>  	tristate "Support for STM32 Low-Power Timer"
>  	depends on (ARCH_STM32 && OF) || COMPILE_TEST
> diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
> index aed99f08739f..ca2d55c679c5 100644
> --- a/drivers/mfd/Makefile
> +++ b/drivers/mfd/Makefile
> @@ -252,6 +252,6 @@ obj-$(CONFIG_MFD_MXS_LRADC)     += mxs-lradc.o
>  obj-$(CONFIG_MFD_SC27XX_PMIC)	+= sprd-sc27xx-spi.o
>  obj-$(CONFIG_RAVE_SP_CORE)	+= rave-sp.o
>  obj-$(CONFIG_MFD_ROHM_BD70528)	+= rohm-bd70528.o
> +obj-$(CONFIG_MFD_ROHM_BD71828)	+= rohm-bd71828.o
>  obj-$(CONFIG_MFD_ROHM_BD718XX)	+= rohm-bd718x7.o
>  obj-$(CONFIG_MFD_STMFX) 	+= stmfx.o
> -

Nit: This is an unrelated change and should not really be in this
patch.

> diff --git a/drivers/mfd/rohm-bd71828.c b/drivers/mfd/rohm-bd71828.c
> new file mode 100644
> index 000000000000..7f445d699fd9
> --- /dev/null
> +++ b/drivers/mfd/rohm-bd71828.c
> @@ -0,0 +1,319 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +//
> +// Copyright (C) 2019 ROHM Semiconductors
> +//
> +// ROHM BD71828 PMIC driver
> +
> +#include <linux/i2c.h>
> +#include <linux/interrupt.h>
> +#include <linux/ioport.h>
> +#include <linux/irq.h>
> +#include <linux/mfd/core.h>
> +#include <linux/mfd/rohm-bd71828.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/regmap.h>
> +#include <linux/types.h>
> +
> +static const struct resource rtc_irqs[] = {
> +	DEFINE_RES_IRQ_NAMED(BD71828_INT_RTC0, "bd71828-rtc-alm-0"),
> +	DEFINE_RES_IRQ_NAMED(BD71828_INT_RTC1, "bd71828-rtc-alm-1"),
> +	DEFINE_RES_IRQ_NAMED(BD71828_INT_RTC2, "bd71828-rtc-alm-2"),
> +};
> +
> +static struct mfd_cell bd71828_mfd_cells[] = {
> +	{ .name = "bd71828-pmic", },
> +	{ .name = "bd71828-gpio", },
> +	{ .name = "bd71828-led", .of_compatible = "rohm,bd71828-leds" },
> +	/*
> +	 * We use BD71837 driver to drive the clock block. Only differences to
> +	 * BD70528 clock gate are the register address and mask.
> +	 */
> +	{ .name = "bd71828-clk", },
> +	{ .name = "bd71827-power", },
> +	{
> +		.name = "bd71828-rtc",
> +		.resources = rtc_irqs,
> +		.num_resources = ARRAY_SIZE(rtc_irqs),
> +	},
> +};
> +
> +static const struct regmap_range volatile_ranges[] = {
> +	{
> +		.range_min = BD71828_REG_PS_CTRL_1,
> +		.range_max = BD71828_REG_PS_CTRL_1,
> +	}, {
> +		.range_min = BD71828_REG_PS_CTRL_3,
> +		.range_max = BD71828_REG_PS_CTRL_3,
> +	}, {
> +		.range_min = BD71828_REG_RTC_SEC,
> +		.range_max = BD71828_REG_RTC_YEAR,
> +	}, {
> +		/*
> +		 * For now make all charger registers volatile because many
> +		 * needs to be and because the charger block is not that
> +		 * performance critical.
> +		 */
> +		.range_min = BD71828_REG_CHG_STATE,
> +		.range_max = BD71828_REG_CHG_FULL,
> +	}, {
> +		.range_min = BD71828_REG_INT_MAIN,
> +		.range_max = BD71828_REG_IO_STAT,
> +	},
> +};
> +
> +static const struct regmap_access_table volatile_regs = {
> +	.yes_ranges = &volatile_ranges[0],
> +	.n_yes_ranges = ARRAY_SIZE(volatile_ranges),
> +};
> +
> +static struct regmap_config bd71828_regmap = {
> +	.reg_bits = 8,
> +	.val_bits = 8,
> +	.volatile_table = &volatile_regs,
> +	.max_register = BD71828_MAX_REGISTER,
> +	.cache_type = REGCACHE_RBTREE,
> +};
> +
> +/*
> + * Mapping of main IRQ register bits to sub-IRQ register offsets so that we can
> + * access corect sub-IRQ registers based on bits that are set in main IRQ
> + * register.
> + */
> +
> +static unsigned int bit0_offsets[] = {11};		/* RTC IRQ */
> +static unsigned int bit1_offsets[] = {10};		/* TEMP IRQ */
> +static unsigned int bit2_offsets[] = {6, 7, 8, 9};	/* BAT MON IRQ */
> +static unsigned int bit3_offsets[] = {5};		/* BAT IRQ */
> +static unsigned int bit4_offsets[] = {4};		/* CHG IRQ */
> +static unsigned int bit5_offsets[] = {3};		/* VSYS IRQ */
> +static unsigned int bit6_offsets[] = {1, 2};		/* DCIN IRQ */
> +static unsigned int bit7_offsets[] = {0};		/* BUCK IRQ */
> +
> +static struct regmap_irq_sub_irq_map bd71828_sub_irq_offsets[] = {
> +	REGMAP_IRQ_MAIN_REG_OFFSET(bit0_offsets),
> +	REGMAP_IRQ_MAIN_REG_OFFSET(bit1_offsets),
> +	REGMAP_IRQ_MAIN_REG_OFFSET(bit2_offsets),
> +	REGMAP_IRQ_MAIN_REG_OFFSET(bit3_offsets),
> +	REGMAP_IRQ_MAIN_REG_OFFSET(bit4_offsets),
> +	REGMAP_IRQ_MAIN_REG_OFFSET(bit5_offsets),
> +	REGMAP_IRQ_MAIN_REG_OFFSET(bit6_offsets),
> +	REGMAP_IRQ_MAIN_REG_OFFSET(bit7_offsets),
> +};
> +
> +static struct regmap_irq bd71828_irqs[] = {
> +	REGMAP_IRQ_REG(BD71828_INT_BUCK1_OCP, 0, BD71828_INT_BUCK1_OCP_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BUCK2_OCP, 0, BD71828_INT_BUCK2_OCP_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BUCK3_OCP, 0, BD71828_INT_BUCK3_OCP_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BUCK4_OCP, 0, BD71828_INT_BUCK4_OCP_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BUCK5_OCP, 0, BD71828_INT_BUCK5_OCP_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BUCK6_OCP, 0, BD71828_INT_BUCK6_OCP_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BUCK7_OCP, 0, BD71828_INT_BUCK7_OCP_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_PGFAULT, 0, BD71828_INT_PGFAULT_MASK),
> +	/* DCIN1 interrupts */
> +	REGMAP_IRQ_REG(BD71828_INT_DCIN_DET, 1, BD71828_INT_DCIN_DET_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_DCIN_RMV, 1, BD71828_INT_DCIN_RMV_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_CLPS_OUT, 1, BD71828_INT_CLPS_OUT_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_CLPS_IN, 1, BD71828_INT_CLPS_IN_MASK),
> +	/* DCIN2 interrupts */
> +	REGMAP_IRQ_REG(BD71828_INT_DCIN_MON_RES, 2,
> +		       BD71828_INT_DCIN_MON_RES_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_DCIN_MON_DET, 2,
> +		       BD71828_INT_DCIN_MON_DET_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_LONGPUSH, 2, BD71828_INT_LONGPUSH_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_MIDPUSH, 2, BD71828_INT_MIDPUSH_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_SHORTPUSH, 2, BD71828_INT_SHORTPUSH_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_PUSH, 2, BD71828_INT_PUSH_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_WDOG, 2, BD71828_INT_WDOG_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_SWRESET, 2, BD71828_INT_SWRESET_MASK),
> +	/* Vsys */
> +	REGMAP_IRQ_REG(BD71828_INT_VSYS_UV_RES, 3,
> +		       BD71828_INT_VSYS_UV_RES_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_VSYS_UV_DET, 3,
> +		       BD71828_INT_VSYS_UV_DET_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_VSYS_LOW_RES, 3,
> +		       BD71828_INT_VSYS_LOW_RES_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_VSYS_LOW_DET, 3,
> +		       BD71828_INT_VSYS_LOW_DET_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_VSYS_HALL_IN, 3,
> +		       BD71828_INT_VSYS_HALL_IN_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_VSYS_HALL_TOGGLE, 3,
> +		       BD71828_INT_VSYS_HALL_TOGGLE_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_VSYS_MON_RES, 3,
> +		       BD71828_INT_VSYS_MON_RES_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_VSYS_MON_DET, 3,
> +		       BD71828_INT_VSYS_MON_DET_MASK),
> +	/* Charger */
> +	REGMAP_IRQ_REG(BD71828_INT_CHG_DCIN_ILIM, 4,
> +		       BD71828_INT_CHG_DCIN_ILIM_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_CHG_TOPOFF_TO_DONE, 4,
> +		       BD71828_INT_CHG_TOPOFF_TO_DONE_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_CHG_WDG_TEMP, 4,
> +		       BD71828_INT_CHG_WDG_TEMP_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_CHG_WDG_TIME, 4,
> +		       BD71828_INT_CHG_WDG_TIME_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_CHG_RECHARGE_RES, 4,
> +		       BD71828_INT_CHG_RECHARGE_RES_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_CHG_RECHARGE_DET, 4,
> +		       BD71828_INT_CHG_RECHARGE_DET_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_CHG_RANGED_TEMP_TRANSITION, 4,
> +		       BD71828_INT_CHG_RANGED_TEMP_TRANSITION_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_CHG_STATE_TRANSITION, 4,
> +		       BD71828_INT_CHG_STATE_TRANSITION_MASK),
> +	/* Battery */
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_TEMP_NORMAL, 5,
> +		       BD71828_INT_BAT_TEMP_NORMAL_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_TEMP_ERANGE, 5,
> +		       BD71828_INT_BAT_TEMP_ERANGE_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_TEMP_WARN, 5,
> +		       BD71828_INT_BAT_TEMP_WARN_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_REMOVED, 5,
> +		       BD71828_INT_BAT_REMOVED_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_DETECTED, 5,
> +		       BD71828_INT_BAT_DETECTED_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_THERM_REMOVED, 5,
> +		       BD71828_INT_THERM_REMOVED_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_THERM_DETECTED, 5,
> +		       BD71828_INT_THERM_DETECTED_MASK),
> +	/* Battery Mon 1 */
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_DEAD, 6, BD71828_INT_BAT_DEAD_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_SHORTC_RES, 6,
> +		       BD71828_INT_BAT_SHORTC_RES_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_SHORTC_DET, 6,
> +		       BD71828_INT_BAT_SHORTC_DET_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_LOW_VOLT_RES, 6,
> +		       BD71828_INT_BAT_LOW_VOLT_RES_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_LOW_VOLT_DET, 6,
> +		       BD71828_INT_BAT_LOW_VOLT_DET_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_VOLT_RES, 6,
> +		       BD71828_INT_BAT_OVER_VOLT_RES_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_VOLT_DET, 6,
> +		       BD71828_INT_BAT_OVER_VOLT_DET_MASK),
> +	/* Battery Mon 2 */
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_MON_RES, 7,
> +		       BD71828_INT_BAT_MON_RES_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_MON_DET, 7,
> +		       BD71828_INT_BAT_MON_DET_MASK),
> +	/* Battery Mon 3 (Coulomb counter) */
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_CC_MON1, 8,
> +		       BD71828_INT_BAT_CC_MON1_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_CC_MON2, 8,
> +		       BD71828_INT_BAT_CC_MON2_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_CC_MON3, 8,
> +		       BD71828_INT_BAT_CC_MON3_MASK),
> +	/* Battery Mon 4 */
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_CURR_1_RES, 9,
> +		       BD71828_INT_BAT_OVER_CURR_1_RES_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_CURR_1_DET, 9,
> +		       BD71828_INT_BAT_OVER_CURR_1_DET_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_CURR_2_RES, 9,
> +		       BD71828_INT_BAT_OVER_CURR_2_RES_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_CURR_2_DET, 9,
> +		       BD71828_INT_BAT_OVER_CURR_2_DET_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_CURR_3_RES, 9,
> +		       BD71828_INT_BAT_OVER_CURR_3_RES_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_CURR_3_DET, 9,
> +		       BD71828_INT_BAT_OVER_CURR_3_DET_MASK),
> +	/* Temperature */
> +	REGMAP_IRQ_REG(BD71828_INT_TEMP_BAT_LOW_RES, 10,
> +		       BD71828_INT_TEMP_BAT_LOW_RES_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_TEMP_BAT_LOW_DET, 10,
> +		       BD71828_INT_TEMP_BAT_LOW_DET_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_TEMP_BAT_HI_RES, 10,
> +		       BD71828_INT_TEMP_BAT_HI_RES_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_TEMP_BAT_HI_DET, 10,
> +		       BD71828_INT_TEMP_BAT_HI_DET_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_TEMP_CHIP_OVER_125_RES, 10,
> +		       BD71828_INT_TEMP_CHIP_OVER_125_RES_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_TEMP_CHIP_OVER_125_DET, 10,
> +		       BD71828_INT_TEMP_CHIP_OVER_125_DET_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_TEMP_CHIP_OVER_VF_DET, 10,
> +		       BD71828_INT_TEMP_CHIP_OVER_VF_DET_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_TEMP_CHIP_OVER_VF_RES, 10,
> +		       BD71828_INT_TEMP_CHIP_OVER_VF_RES_MASK),
> +	/* RTC Alarm */
> +	REGMAP_IRQ_REG(BD71828_INT_RTC0, 11, BD71828_INT_RTC0_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_RTC1, 11, BD71828_INT_RTC1_MASK),
> +	REGMAP_IRQ_REG(BD71828_INT_RTC2, 11, BD71828_INT_RTC2_MASK),
> +};
> +
> +static struct regmap_irq_chip bd71828_irq_chip = {
> +	.name = "bd71828_irq",
> +	.main_status = BD71828_REG_INT_MAIN,
> +	.irqs = &bd71828_irqs[0],
> +	.num_irqs = ARRAY_SIZE(bd71828_irqs),
> +	.status_base = BD71828_REG_INT_BUCK,
> +	.mask_base = BD71828_REG_INT_MASK_BUCK,
> +	.ack_base = BD71828_REG_INT_BUCK,
> +	.mask_invert = true,
> +	.init_ack_masked = true,
> +	.num_regs = 12,
> +	.num_main_regs = 1,
> +	.sub_reg_offsets = &bd71828_sub_irq_offsets[0],
> +	.num_main_status_bits = 8,
> +	.irq_reg_stride = 1,
> +};
> +
> +static int bd71828_i2c_probe(struct i2c_client *i2c)
> +{
> +	struct rohm_regmap_dev *chip;
> +	struct regmap_irq_chip_data *irq_data;
> +	int ret;
> +
> +	if (!i2c->irq) {
> +		dev_err(&i2c->dev, "No IRQ configured\n");
> +		return -EINVAL;
> +	}
> +
> +	chip = devm_kzalloc(&i2c->dev, sizeof(*chip), GFP_KERNEL);
> +	if (!chip)
> +		return -ENOMEM;
> +
> +	dev_set_drvdata(&i2c->dev, chip);
> +
> +	chip->regmap = devm_regmap_init_i2c(i2c, &bd71828_regmap);
> +	if (IS_ERR(chip->regmap)) {
> +		dev_err(&i2c->dev, "Failed to initialize Regmap\n");
> +		return PTR_ERR(chip->regmap);
> +	}
> +
> +	ret = devm_regmap_add_irq_chip(&i2c->dev, chip->regmap,
> +				       i2c->irq, IRQF_ONESHOT, 0,
> +				       &bd71828_irq_chip, &irq_data);
> +	if (ret) {
> +		dev_err(&i2c->dev, "Failed to add IRQ chip\n");
> +		return ret;
> +	}
> +
> +	dev_dbg(&i2c->dev, "Registered %d IRQs for chip\n",
> +		bd71828_irq_chip.num_irqs);
> +
> +	ret = devm_mfd_add_devices(&i2c->dev, PLATFORM_DEVID_AUTO,
> +				   bd71828_mfd_cells,
> +				   ARRAY_SIZE(bd71828_mfd_cells), NULL, 0,
> +				   regmap_irq_get_domain(irq_data));
> +	if (ret)
> +		dev_err(&i2c->dev, "Failed to create subdevices\n");
> +
> +	return ret;
> +}
> +
> +static const struct of_device_id bd71828_of_match[] = {
> +	{ .compatible = "rohm,bd71828", },
> +	{ },
> +};
> +MODULE_DEVICE_TABLE(of, bd71828_of_match);
> +
> +static struct i2c_driver bd71828_drv = {
> +	.driver = {
> +		.name = "rohm-bd71828",
> +		.of_match_table = bd71828_of_match,
> +	},
> +	.probe_new = &bd71828_i2c_probe,
> +};
> +

Nit: You can remove this line.

> +module_i2c_driver(bd71828_drv);
> +
> +MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
> +MODULE_DESCRIPTION("ROHM BD71828 Power Management IC driver");
> +MODULE_LICENSE("GPL");

This does not match the header.

-- 
Lee Jones [李琼斯]
Linaro Services Technical Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

  reply	other threads:[~2019-12-16 16:46 UTC|newest]

Thread overview: 44+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-12-11  9:33 [PATCH v6 00/15] Support ROHM BD71828 PMIC Matti Vaittinen
2019-12-11  9:35 ` [PATCH v6 01/15] dt-bindings: regulator: Document ROHM BD71282 regulator bindings Matti Vaittinen
2019-12-17 12:39   ` Applied "dt-bindings: regulator: Document ROHM BD71282 regulator bindings" to the regulator tree Mark Brown
2019-12-11  9:36 ` [PATCH v6 02/15] dt-bindings: leds: ROHM BD71282 PMIC LED driver Matti Vaittinen
2019-12-18 18:07   ` Rob Herring
2019-12-11  9:37 ` [PATCH v6 03/15] dt-bindings: mfd: Document ROHM BD71828 bindings Matti Vaittinen
2019-12-18 18:08   ` Rob Herring
2019-12-11  9:39 ` [PATCH v6 04/15] mfd: rohm PMICs - use platform_device_id to match MFD sub-devices Matti Vaittinen
2019-12-16 16:41   ` Lee Jones
2019-12-11  9:42 ` [PATCH v6 05/15] mfd: bd71828: Support ROHM BD71828 PMIC - core Matti Vaittinen
2019-12-16 16:46   ` Lee Jones [this message]
2019-12-17  9:39     ` Vaittinen, Matti
2019-12-17 13:54       ` Lee Jones
2019-12-17 14:08         ` gregkh
2019-12-17 14:25           ` Lee Jones
2019-12-11  9:43 ` [PATCH v6 06/15] mfd: input: bd71828: Add power-key support Matti Vaittinen
2019-12-11  9:43 ` [PATCH v6 07/15] clk: bd718x7: Support ROHM BD71828 clk block Matti Vaittinen
2019-12-16 16:47   ` Lee Jones
2019-12-11  9:44 ` [PATCH v6 08/15] regulator: bd718x7: Split driver to common and bd718x7 specific parts Matti Vaittinen
2019-12-18 13:12   ` Mark Brown
2019-12-18 17:27   ` Mark Brown
2019-12-11  9:46 ` [PATCH v6 09/15] regulator: bd71828: Basic support for ROHM bd71828 PMIC regulators Matti Vaittinen
2019-12-16 14:55   ` Mark Brown
2019-12-17  6:56     ` Vaittinen, Matti
2019-12-17  9:15     ` Vaittinen, Matti
2019-12-17 12:39   ` Applied "regulator: bd71828: Basic support for ROHM bd71828 PMIC regulators" to the regulator tree Mark Brown
2019-12-18  8:06     ` Vaittinen, Matti
2019-12-18 13:17       ` Mark Brown
2019-12-18 13:33         ` Vaittinen, Matti
2019-12-18 14:01         ` Vaittinen, Matti
2019-12-18 17:24           ` Mark Brown
2019-12-11  9:47 ` [PATCH v6 10/15] gpio: devres: Add devm_gpiod_get_parent_array Matti Vaittinen
2019-12-16  8:29   ` Linus Walleij
2019-12-16  8:59     ` Vaittinen, Matti
2019-12-16 12:21       ` Linus Walleij
2019-12-11  9:47 ` [PATCH v6 11/15] docs: driver-model: Add missing managed GPIO array get functions Matti Vaittinen
2019-12-16  8:31   ` Linus Walleij
2019-12-11  9:48 ` [PATCH v6 12/15] rtc: bd70528 add BD71828 support Matti Vaittinen
2019-12-11 11:38   ` Alexandre Belloni
2019-12-11 11:48     ` Vaittinen, Matti
2019-12-11  9:49 ` [PATCH v6 13/15] gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs Matti Vaittinen
2019-12-16  8:32   ` Linus Walleij
2019-12-11 10:00 ` [PATCH v6 14/15] leds: Add common LED binding parsing support to LED class/core Matti Vaittinen
2019-12-11 10:02 ` [PATCH v6 15/15] led: bd71828: Support LED outputs on ROHM BD71828 PMIC Matti Vaittinen

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20191216164641.GC18955@dell \
    --to=lee.jones@linaro.org \
    --cc=a.zummo@towertech.it \
    --cc=alexandre.belloni@bootlin.com \
    --cc=arnd@arndb.de \
    --cc=bgolaszewski@baylibre.com \
    --cc=broonie@kernel.org \
    --cc=corbet@lwn.net \
    --cc=devicetree@vger.kernel.org \
    --cc=dmurphy@ti.com \
    --cc=gregkh@linuxfoundation.org \
    --cc=jacek.anaszewski@gmail.com \
    --cc=lgirdwood@gmail.com \
    --cc=linus.walleij@linaro.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-doc@vger.kernel.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-leds@vger.kernel.org \
    --cc=linux-rtc@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=matti.vaittinen@fi.rohmeurope.com \
    --cc=mazziesaccount@gmail.com \
    --cc=mchehab+samsung@kernel.org \
    --cc=mturquette@baylibre.com \
    --cc=noralf@tronnes.org \
    --cc=pavel@ucw.cz \
    --cc=phil.edworthy@renesas.com \
    --cc=robh+dt@kernel.org \
    --cc=sboyd@kernel.org \
    --cc=wsa+renesas@sang-engineering.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).