* [PATCH 0/4] Allwinner A100 Initial support
@ 2020-05-22 3:07 Frank Lee
2020-05-22 3:07 ` [PATCH 1/4] clk: sunxi-ng: add support for the Allwinner A100 CCU Frank Lee
` (4 more replies)
0 siblings, 5 replies; 15+ messages in thread
From: Frank Lee @ 2020-05-22 3:07 UTC (permalink / raw)
To: mripard, wens, robh+dt, mturquette, sboyd, linus.walleij,
p.zabel, frank, huangshuosheng, tiny.windzz
Cc: linux-arm-kernel, devicetree, linux-kernel, linux-clk, linux-gpio
This patch set adds initial support for allwinner a100 soc,
which is a 64-bit tablet chip.
Frank Lee (4):
clk: sunxi-ng: add support for the Allwinner A100 CCU
pinctrl: sunxi: add support for the Allwinner A100 pin controller
arm64: allwinner: A100: add the basical Allwinner A100 DTSI file
arm64: allwinner: A100: add support for Allwinner Perf1 board
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../allwinner/sun50i-a100-allwinner-perf1.dts | 27 +
.../arm64/boot/dts/allwinner/sun50i-a100.dtsi | 173 +++
drivers/clk/sunxi-ng/Kconfig | 10 +
drivers/clk/sunxi-ng/Makefile | 2 +
drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c | 206 +++
drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h | 14 +
drivers/clk/sunxi-ng/ccu-sun50i-a100.c | 1255 +++++++++++++++++
drivers/clk/sunxi-ng/ccu-sun50i-a100.h | 14 +
drivers/pinctrl/sunxi/Kconfig | 10 +
drivers/pinctrl/sunxi/Makefile | 2 +
drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c | 105 ++
drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c | 710 ++++++++++
include/dt-bindings/clock/sun50i-a100-ccu.h | 141 ++
include/dt-bindings/clock/sun50i-a100-r-ccu.h | 25 +
include/dt-bindings/reset/sun50i-a100-ccu.h | 68 +
include/dt-bindings/reset/sun50i-a100-r-ccu.h | 18 +
17 files changed, 2781 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a100-allwinner-perf1.dts
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.h
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c
create mode 100644 include/dt-bindings/clock/sun50i-a100-ccu.h
create mode 100644 include/dt-bindings/clock/sun50i-a100-r-ccu.h
create mode 100644 include/dt-bindings/reset/sun50i-a100-ccu.h
create mode 100644 include/dt-bindings/reset/sun50i-a100-r-ccu.h
--
2.24.0
^ permalink raw reply [flat|nested] 15+ messages in thread* [PATCH 1/4] clk: sunxi-ng: add support for the Allwinner A100 CCU 2020-05-22 3:07 [PATCH 0/4] Allwinner A100 Initial support Frank Lee @ 2020-05-22 3:07 ` Frank Lee 2020-05-22 15:14 ` Maxime Ripard 2020-05-22 3:07 ` [PATCH 2/4] pinctrl: sunxi: add support for the Allwinner A100 pin controller Frank Lee ` (3 subsequent siblings) 4 siblings, 1 reply; 15+ messages in thread From: Frank Lee @ 2020-05-22 3:07 UTC (permalink / raw) To: mripard, wens, robh+dt, mturquette, sboyd, linus.walleij, p.zabel, frank, huangshuosheng, tiny.windzz Cc: linux-arm-kernel, devicetree, linux-kernel, linux-clk, linux-gpio Add support for a100 in the sunxi-ng CCU framework. Signed-off-by: Frank Lee <frank@allwinnertech.com> --- drivers/clk/sunxi-ng/Kconfig | 10 + drivers/clk/sunxi-ng/Makefile | 2 + drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c | 206 +++ drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h | 14 + drivers/clk/sunxi-ng/ccu-sun50i-a100.c | 1255 +++++++++++++++++ drivers/clk/sunxi-ng/ccu-sun50i-a100.h | 14 + include/dt-bindings/clock/sun50i-a100-ccu.h | 141 ++ include/dt-bindings/clock/sun50i-a100-r-ccu.h | 25 + include/dt-bindings/reset/sun50i-a100-ccu.h | 68 + include/dt-bindings/reset/sun50i-a100-r-ccu.h | 18 + 10 files changed, 1753 insertions(+) create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.c create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.h create mode 100644 include/dt-bindings/clock/sun50i-a100-ccu.h create mode 100644 include/dt-bindings/clock/sun50i-a100-r-ccu.h create mode 100644 include/dt-bindings/reset/sun50i-a100-ccu.h create mode 100644 include/dt-bindings/reset/sun50i-a100-r-ccu.h diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig index cdf333003c30..ce5f5847d5d3 100644 --- a/drivers/clk/sunxi-ng/Kconfig +++ b/drivers/clk/sunxi-ng/Kconfig @@ -17,6 +17,16 @@ config SUN50I_A64_CCU default ARM64 && ARCH_SUNXI depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST +config SUN50I_A100_CCU + bool "Support for the Allwinner A100 CCU" + default ARM64 && ARCH_SUNXI + depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST + +config SUN50I_A100_R_CCU + bool "Support for the Allwinner A100 PRCM CCU" + default ARM64 && ARCH_SUNXI + depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST + config SUN50I_H6_CCU bool "Support for the Allwinner H6 CCU" default ARM64 && ARCH_SUNXI diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile index 4c7bee883f2f..3eb5cff40eac 100644 --- a/drivers/clk/sunxi-ng/Makefile +++ b/drivers/clk/sunxi-ng/Makefile @@ -23,6 +23,8 @@ obj-y += ccu_mp.o # SoC support obj-$(CONFIG_SUNIV_F1C100S_CCU) += ccu-suniv-f1c100s.o obj-$(CONFIG_SUN50I_A64_CCU) += ccu-sun50i-a64.o +obj-$(CONFIG_SUN50I_A100_CCU) += ccu-sun50i-a100.o +obj-$(CONFIG_SUN50I_A100_R_CCU) += ccu-sun50i-a100-r.o obj-$(CONFIG_SUN50I_H6_CCU) += ccu-sun50i-h6.o obj-$(CONFIG_SUN50I_H6_R_CCU) += ccu-sun50i-h6-r.o obj-$(CONFIG_SUN4I_A10_CCU) += ccu-sun4i-a10.o diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c new file mode 100644 index 000000000000..31875269ef90 --- /dev/null +++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c @@ -0,0 +1,206 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2020 Frank Lee <frank@allwinner.com> + */ + +#include <linux/clk-provider.h> +#include <linux/module.h> +#include <linux/of_address.h> +#include <linux/platform_device.h> + +#include "ccu_common.h" +#include "ccu_reset.h" + +#include "ccu_div.h" +#include "ccu_gate.h" +#include "ccu_mp.h" +#include "ccu_nm.h" + +#include "ccu-sun50i-a100-r.h" + +static const char * const cpus_r_apb2_parents[] = { "dcxo24M", "osc32k", + "iosc", "pll-periph0" }; +static const struct ccu_mux_var_prediv cpus_r_apb2_predivs[] = { + { .index = 3, .shift = 0, .width = 5 }, +}; + +static struct ccu_div cpus_clk = { + .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO), + + .mux = { + .shift = 24, + .width = 2, + + .var_predivs = cpus_r_apb2_predivs, + .n_var_predivs = ARRAY_SIZE(cpus_r_apb2_predivs), + }, + + .common = { + .reg = 0x000, + .features = CCU_FEATURE_VARIABLE_PREDIV, + .hw.init = CLK_HW_INIT_PARENTS("cpus", + cpus_r_apb2_parents, + &ccu_div_ops, + 0), + }, +}; + +static CLK_FIXED_FACTOR_HW(r_ahb_clk, "r-ahb", &cpus_clk.common.hw, 1, 1, 0); + +static struct ccu_div r_apb1_clk = { + .div = _SUNXI_CCU_DIV(0, 2), + + .common = { + .reg = 0x00c, + .hw.init = CLK_HW_INIT("r-apb1", + "r-ahb", + &ccu_div_ops, + 0), + }, +}; + +static struct ccu_div r_apb2_clk = { + .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO), + + .mux = { + .shift = 24, + .width = 2, + + .var_predivs = cpus_r_apb2_predivs, + .n_var_predivs = ARRAY_SIZE(cpus_r_apb2_predivs), + }, + + .common = { + .reg = 0x010, + .features = CCU_FEATURE_VARIABLE_PREDIV, + .hw.init = CLK_HW_INIT_PARENTS("r-apb2", + cpus_r_apb2_parents, + &ccu_div_ops, + 0), + }, +}; + +static SUNXI_CCU_GATE(r_apb1_timer_clk, "r-apb1-timer", "r-apb1", + 0x11c, BIT(0), 0); + +static SUNXI_CCU_GATE(r_apb1_twd_clk, "r-apb1-twd", "r-apb1", + 0x12c, BIT(0), 0); + +static const char * const r_apb1_pwm_clk_parents[] = { "dcxo24M", "osc32k", + "iosc" }; +static SUNXI_CCU_MUX(r_apb1_pwm_clk, "r-apb1-pwm", r_apb1_pwm_clk_parents, + 0x130, 24, 2, 0); + +static SUNXI_CCU_GATE(r_apb1_bus_pwm_clk, "r-apb1-bus-pwm", "r-apb1", + 0x13c, BIT(0), 0); + +static SUNXI_CCU_GATE(r_apb1_ppu_clk, "r-apb1-ppu", "r-apb1", + 0x17c, BIT(0), 0); + +static SUNXI_CCU_GATE(r_apb2_uart_clk, "r-apb2-uart", "r-apb2", + 0x18c, BIT(0), 0); + +static SUNXI_CCU_GATE(r_apb2_i2c0_clk, "r-apb2-i2c0", "r-apb2", + 0x19c, BIT(0), 0); + +static SUNXI_CCU_GATE(r_apb2_i2c1_clk, "r-apb2-i2c1", "r-apb2", + 0x19c, BIT(1), 0); + +static const char * const r_apb1_ir_rx_parents[] = { "osc32k", "dcxo24M" }; +static SUNXI_CCU_MP_WITH_MUX_GATE(r_apb1_ir_rx_clk, "r-apb1-ir-rx", + r_apb1_ir_rx_parents, 0x1c0, + 0, 5, /* M */ + 8, 2, /* P */ + 24, 1, /* mux */ + BIT(31), /* gate */ + 0); + +static SUNXI_CCU_GATE(r_apb1_bus_ir_rx_clk, "r-apb1-bus-ir-rx", "r-apb1", + 0x1cc, BIT(0), 0); + +static SUNXI_CCU_GATE(r_ahb_bus_rtc_clk, "r-ahb-rtc", "r-ahb", + 0x20c, BIT(0), 0); + +static struct ccu_common *sun50i_a100_r_ccu_clks[] = { + &cpus_clk.common, + &r_apb1_clk.common, + &r_apb2_clk.common, + &r_apb1_timer_clk.common, + &r_apb1_twd_clk.common, + &r_apb1_pwm_clk.common, + &r_apb1_bus_pwm_clk.common, + &r_apb1_ppu_clk.common, + &r_apb2_uart_clk.common, + &r_apb2_i2c0_clk.common, + &r_apb2_i2c1_clk.common, + &r_apb1_ir_rx_clk.common, + &r_apb1_bus_ir_rx_clk.common, + &r_ahb_bus_rtc_clk.common, +}; + +static struct clk_hw_onecell_data sun50i_a100_r_hw_clks = { + .hws = { + [CLK_CPUS] = &cpus_clk.common.hw, + [CLK_R_AHB] = &r_ahb_clk.hw, + [CLK_R_APB1] = &r_apb1_clk.common.hw, + [CLK_R_APB2] = &r_apb2_clk.common.hw, + [CLK_R_APB1_TIMER] = &r_apb1_timer_clk.common.hw, + [CLK_R_APB1_TWD] = &r_apb1_twd_clk.common.hw, + [CLK_R_APB1_PWM] = &r_apb1_pwm_clk.common.hw, + [CLK_R_APB1_BUS_PWM] = &r_apb1_bus_pwm_clk.common.hw, + [CLK_R_APB1_PPU] = &r_apb1_ppu_clk.common.hw, + [CLK_R_APB2_UART] = &r_apb2_uart_clk.common.hw, + [CLK_R_APB2_I2C0] = &r_apb2_i2c0_clk.common.hw, + [CLK_R_APB2_I2C1] = &r_apb2_i2c1_clk.common.hw, + [CLK_R_APB1_IR] = &r_apb1_ir_rx_clk.common.hw, + [CLK_R_APB1_BUS_IR] = &r_apb1_bus_ir_rx_clk.common.hw, + [CLK_R_AHB_BUS_RTC] = &r_ahb_bus_rtc_clk.common.hw, + }, + .num = CLK_NUMBER, +}; + +static struct ccu_reset_map sun50i_a100_r_ccu_resets[] = { + [RST_R_APB1_TIMER] = { 0x11c, BIT(16) }, + [RST_R_APB1_BUS_PWM] = { 0x13c, BIT(16) }, + [RST_R_APB1_PPU] = { 0x17c, BIT(16) }, + [RST_R_APB2_UART] = { 0x18c, BIT(16) }, + [RST_R_APB2_I2C0] = { 0x19c, BIT(16) }, + [RST_R_APB2_I2C1] = { 0x19c, BIT(17) }, + [RST_R_APB1_BUS_IR] = { 0x1cc, BIT(16) }, + [RST_R_AHB_BUS_RTC] = { 0x20c, BIT(16) }, +}; + +static const struct sunxi_ccu_desc sun50i_a100_r_ccu_desc = { + .ccu_clks = sun50i_a100_r_ccu_clks, + .num_ccu_clks = ARRAY_SIZE(sun50i_a100_r_ccu_clks), + + .hw_clks = &sun50i_a100_r_hw_clks, + + .resets = sun50i_a100_r_ccu_resets, + .num_resets = ARRAY_SIZE(sun50i_a100_r_ccu_resets), +}; + +static int sun50i_a100_r_ccu_probe(struct platform_device *pdev) +{ + void __iomem *reg; + + reg = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(reg)) + return PTR_ERR(reg); + + return sunxi_ccu_probe(pdev->dev.of_node, reg, &sun50i_a100_r_ccu_desc); +} + +static const struct of_device_id sun50i_a100_r_ccu_ids[] = { + { .compatible = "allwinner,sun50i-a100-r-ccu" }, + { } +}; + +static struct platform_driver sun50i_a100_r_ccu_driver = { + .probe = sun50i_a100_r_ccu_probe, + .driver = { + .name = "sun50i-a100-r-ccu", + .of_match_table = sun50i_a100_r_ccu_ids, + }, +}; +module_platform_driver(sun50i_a100_r_ccu_driver); diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h new file mode 100644 index 000000000000..c26a08b924db --- /dev/null +++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h @@ -0,0 +1,14 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (c) 2020 Frank Lee <frank@allwinner.com> + */ + +#ifndef _CCU_SUN50IW10_R_H +#define _CCU_SUN50IW10_R_H + +#include <dt-bindings/clock/sun50i-a100-r-ccu.h> +#include <dt-bindings/reset/sun50i-a100-r-ccu.h> + +#define CLK_NUMBER (CLK_R_AHB_BUS_RTC + 1) + +#endif /* _CCU_SUN50IW10_R_H */ diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100.c b/drivers/clk/sunxi-ng/ccu-sun50i-a100.c new file mode 100644 index 000000000000..f9a0a7754eed --- /dev/null +++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100.c @@ -0,0 +1,1255 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2020 Frank Lee <frank@allwinner.com> + */ + +#include <linux/clk-provider.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/of_address.h> +#include <linux/platform_device.h> + +#include "ccu_common.h" +#include "ccu_reset.h" + +#include "ccu_div.h" +#include "ccu_gate.h" +#include "ccu_mp.h" +#include "ccu_mult.h" +#include "ccu_nk.h" +#include "ccu_nkm.h" +#include "ccu_nkmp.h" +#include "ccu_nm.h" + +#include "ccu-sun50i-a100.h" + +/* + * The CPU PLL is actually NP clock, with P being /1, /2 or /4. However + * P should only be used for output frequencies lower than 288 MHz. + * + * For now we can just model it as a multiplier clock, and force P to /1. + * + * The M factor is present in the register's description, but not in the + * frequency formula, and it's documented as "M is only used for backdoor + * testing", so it's not modelled and then force to 0. + */ +#define SUN50I_A100_PLL_CPUX_REG 0x000 +static struct ccu_mult pll_cpux_clk = { + .enable = BIT(27), + .lock = BIT(28), + .mult = _SUNXI_CCU_MULT_MIN(8, 8, 12), + .common = { + .reg = 0x000, + .hw.init = CLK_HW_INIT("pll-cpux", "dcxo24M", + &ccu_mult_ops, + CLK_SET_RATE_UNGATE), + }, +}; + +/* Some PLLs are input * N / div1 / P. Model them as NKMP with no K */ +#define SUN50I_A100_PLL_DDR0_REG 0x010 +static struct ccu_nkmp pll_ddr0_clk = { + .enable = BIT(27), + .lock = BIT(28), + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), + .m = _SUNXI_CCU_DIV(1, 1), /* input divider */ + .p = _SUNXI_CCU_DIV(0, 1), /* output divider */ + .common = { + .reg = 0x010, + .hw.init = CLK_HW_INIT("pll-ddr0", "dcxo24M", + &ccu_nkmp_ops, + CLK_SET_RATE_UNGATE | + CLK_IS_CRITICAL), + }, +}; + +#define SUN50I_A100_PLL_PERIPH0_REG 0x020 +static struct ccu_nkmp pll_periph0_clk = { + .enable = BIT(27), + .lock = BIT(28), + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), + .m = _SUNXI_CCU_DIV(1, 1), /* input divider */ + .p = _SUNXI_CCU_DIV(0, 1), /* output divider */ + .fixed_post_div = 2, + .common = { + .reg = 0x020, + .features = CCU_FEATURE_FIXED_POSTDIV, + .hw.init = CLK_HW_INIT("pll-periph0", "dcxo24M", + &ccu_nkmp_ops, + CLK_SET_RATE_UNGATE), + }, +}; + +#define SUN50I_A100_PLL_PERIPH1_REG 0x028 +static struct ccu_nkmp pll_periph1_clk = { + .enable = BIT(27), + .lock = BIT(28), + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), + .m = _SUNXI_CCU_DIV(1, 1), /* input divider */ + .p = _SUNXI_CCU_DIV(0, 1), /* output divider */ + .fixed_post_div = 2, + .common = { + .reg = 0x028, + .features = CCU_FEATURE_FIXED_POSTDIV, + .hw.init = CLK_HW_INIT("pll-periph1", "dcxo24M", + &ccu_nkmp_ops, + CLK_SET_RATE_UNGATE), + }, +}; +#define SUN50I_A100_PLL_PERIPH1_PATTERN0_REG 0x128 + +#define SUN50I_A100_PLL_GPU_REG 0x030 +static struct ccu_nkmp pll_gpu_clk = { + .enable = BIT(27), + .lock = BIT(28), + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), + .m = _SUNXI_CCU_DIV(1, 1), /* input divider */ + .p = _SUNXI_CCU_DIV(0, 1), /* output divider */ + .common = { + .reg = 0x030, + .hw.init = CLK_HW_INIT("pll-gpu", "dcxo24M", + &ccu_nkmp_ops, + CLK_SET_RATE_UNGATE), + }, +}; + +/* + * For Video PLLs, the output divider is described as "used for testing" + * in the user manual. So it's not modelled and forced to 0. + */ +#define SUN50I_A100_PLL_VIDEO0_REG 0x040 +static struct ccu_nm pll_video0_clk = { + .enable = BIT(27), + .lock = BIT(28), + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), + .m = _SUNXI_CCU_DIV(1, 1), /* input divider */ + .fixed_post_div = 4, + .common = { + .reg = 0x040, + .features = CCU_FEATURE_FIXED_POSTDIV, + .hw.init = CLK_HW_INIT("pll-video0", "dcxo24M", + &ccu_nm_ops, + CLK_SET_RATE_UNGATE), + }, +}; + +#define SUN50I_A100_PLL_VIDEO1_REG 0x048 +static struct ccu_nm pll_video1_clk = { + .enable = BIT(27), + .lock = BIT(28), + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), + .m = _SUNXI_CCU_DIV(1, 1), /* input divider */ + .fixed_post_div = 4, + .common = { + .reg = 0x048, + .features = CCU_FEATURE_FIXED_POSTDIV, + .hw.init = CLK_HW_INIT("pll-video1", "dcxo24M", + &ccu_nm_ops, + CLK_SET_RATE_UNGATE), + }, +}; + +#define SUN50I_A100_PLL_VIDEO2_REG 0x050 +static struct ccu_nm pll_video2_clk = { + .enable = BIT(27), + .lock = BIT(28), + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), + .m = _SUNXI_CCU_DIV(1, 1), /* input divider */ + .fixed_post_div = 4, + .common = { + .reg = 0x050, + .features = CCU_FEATURE_FIXED_POSTDIV, + .hw.init = CLK_HW_INIT("pll-video2", "dcxo24M", + &ccu_nm_ops, + CLK_SET_RATE_UNGATE), + }, +}; + +#define SUN50I_A100_PLL_VE_REG 0x058 +static struct ccu_nkmp pll_ve_clk = { + .enable = BIT(27), + .lock = BIT(28), + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), + .m = _SUNXI_CCU_DIV(1, 1), /* input divider */ + .p = _SUNXI_CCU_DIV(0, 1), /* output divider */ + .common = { + .reg = 0x058, + .hw.init = CLK_HW_INIT("pll-ve", "dcxo24M", + &ccu_nkmp_ops, + CLK_SET_RATE_UNGATE), + }, +}; + +/* + * The COM PLL has m0 dividers in addition to the usual N, M + * factors. Since we only need 1 frequencies from this PLL: 45.1584 MHz, + * ignore it for now. + */ +#define SUN50I_A100_PLL_COM_REG 0x060 +static struct ccu_sdm_setting pll_com_sdm_table[] = { + { .rate = 451584000, .pattern = 0xc0014396, .m = 2, .n = 37 }, +}; + +static struct ccu_nm pll_com_clk = { + .enable = BIT(27), + .lock = BIT(28), + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), + .m = _SUNXI_CCU_DIV(0, 1), + .sdm = _SUNXI_CCU_SDM(pll_com_sdm_table, BIT(24), + 0x160, BIT(31)), + .common = { + .reg = 0x060, + .features = CCU_FEATURE_SIGMA_DELTA_MOD, + .hw.init = CLK_HW_INIT("pll-com", "dcxo24M", + &ccu_nm_ops, + CLK_SET_RATE_UNGATE), + }, +}; + +#define SUN50I_A100_PLL_VIDEO3_REG 0x068 +static struct ccu_nm pll_video3_clk = { + .enable = BIT(27), + .lock = BIT(28), + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), + .m = _SUNXI_CCU_DIV(1, 1), /* input divider */ + .fixed_post_div = 4, + .common = { + .reg = 0x068, + .features = CCU_FEATURE_FIXED_POSTDIV, + .hw.init = CLK_HW_INIT("pll-video3", "dcxo24M", + &ccu_nm_ops, + CLK_SET_RATE_UNGATE), + }, +}; + +/* + * The Audio PLL has m0, m1 dividers in addition to the usual N, M + * factors. Since we only need 4 frequencies from this PLL: 22.5792 MHz, + * 24.576 MHz, 90.3168MHz and 98.304MHz ignore them for now. + * Enforce the default for them, which is m0 = 1, m1 = 0. + */ +#define SUN50I_A100_PLL_AUDIO_REG 0x078 +static struct ccu_sdm_setting pll_audio_sdm_table[] = { + { .rate = 45158400, .pattern = 0xc001bcd3, .m = 18, .n = 33 }, + { .rate = 49152000, .pattern = 0xc001eb85, .m = 20, .n = 40 }, + { .rate = 180633600, .pattern = 0xc001288d, .m = 3, .n = 22 }, + { .rate = 196608000, .pattern = 0xc001eb85, .m = 5, .n = 40 }, +}; + +static struct ccu_nm pll_audio_clk = { + .enable = BIT(27), + .lock = BIT(28), + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), + .m = _SUNXI_CCU_DIV(16, 6), + .fixed_post_div = 2, + .sdm = _SUNXI_CCU_SDM(pll_audio_sdm_table, BIT(24), + 0x178, BIT(31)), + .common = { + .reg = 0x078, + .features = CCU_FEATURE_FIXED_POSTDIV | + CCU_FEATURE_SIGMA_DELTA_MOD, + .hw.init = CLK_HW_INIT("pll-audio", "dcxo24M", + &ccu_nm_ops, + CLK_SET_RATE_UNGATE), + }, +}; + +static const char * const cpux_parents[] = { "dcxo24M", "osc32k", + "iosc", "pll-cpux", + "pll-periph0" }; +static SUNXI_CCU_MUX(cpux_clk, "cpux", cpux_parents, + 0x500, 24, 3, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL); +static SUNXI_CCU_M(axi_clk, "axi", "cpux", 0x500, 0, 2, 0); +static SUNXI_CCU_M(cpux_apb_clk, "cpux-apb", "cpux", 0x500, 8, 2, 0); + +static const char * const psi_ahb1_ahb2_parents[] = { "dcxo24M", "osc32k", + "iosc", "pll-periph0", + "pll-periph0-2x" }; +static SUNXI_CCU_MP_WITH_MUX(psi_ahb1_ahb2_clk, "psi-ahb1-ahb2", + psi_ahb1_ahb2_parents, + 0x510, + 0, 2, /* M */ + 8, 2, /* P */ + 24, 3, /* mux */ + 0); + +static const char * const ahb3_apb1_apb2_parents[] = { "dcxo24M", "osc32k", + "psi-ahb1-ahb2", + "pll-periph0", + "pll-periph0-2x" }; +static SUNXI_CCU_MP_WITH_MUX(ahb3_clk, "ahb3", ahb3_apb1_apb2_parents, 0x51c, + 0, 2, /* M */ + 8, 2, /* P */ + 24, 3, /* mux */ + 0); + +static SUNXI_CCU_MP_WITH_MUX(apb1_clk, "apb1", ahb3_apb1_apb2_parents, 0x520, + 0, 2, /* M */ + 8, 2, /* P */ + 24, 3, /* mux */ + 0); + +static SUNXI_CCU_MP_WITH_MUX(apb2_clk, "apb2", ahb3_apb1_apb2_parents, 0x524, + 0, 2, /* M */ + 8, 2, /* P */ + 24, 3, /* mux */ + 0); + +static const char * const mbus_parents[] = { "dcxo24M", "pll-ddr0", + "pll-periph0", + "pll-periph0-2x" }; +static SUNXI_CCU_M_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents, 0x540, + 0, 3, /* M */ + 24, 2, /* mux */ + BIT(31), /* gate */ + CLK_IS_CRITICAL); + +static const char * const de_parents[] = { "pll-com", "pll-periph0-2x" }; +static SUNXI_CCU_M_WITH_MUX_GATE(de_clk, "de0", de_parents, 0x600, + 0, 4, /* M */ + 24, 1, /* mux */ + BIT(31), /* gate */ + CLK_SET_RATE_PARENT); + +static SUNXI_CCU_GATE(bus_de_clk, "bus-de", "psi-ahb1-ahb2", + 0x60c, BIT(0), 0); + +static const char * const g2d_parents[] = { "pll-com", "pll-periph0-2x", + "pll-video0-2x", "pll-video1-2x", + "pll-video2-2x"}; +static SUNXI_CCU_M_WITH_MUX_GATE(g2d_clk, "g2d", + g2d_parents, + 0x630, + 0, 4, /* M */ + 24, 3, /* mux */ + BIT(31), /* gate */ + 0); + +static SUNXI_CCU_GATE(bus_g2d_clk, "bus-g2d", "psi-ahb1-ahb2", + 0x63c, BIT(0), 0); + +static const char * const gpu_parents[] = { "pll-gpu" }; +static SUNXI_CCU_M_WITH_MUX_GATE(gpu_clk, "gpu", gpu_parents, 0x670, + 0, 2, /* M */ + 24, 1, /* mux */ + BIT(31), /* gate */ + 0); + +static SUNXI_CCU_GATE(bus_gpu_clk, "bus-gpu", "psi-ahb1-ahb2", + 0x67c, BIT(0), 0); + +static const char * const ce_parents[] = { "dcxo24M", "pll-periph0-2x" }; +static SUNXI_CCU_MP_WITH_MUX_GATE(ce_clk, "ce", ce_parents, 0x680, + 0, 4, /* M */ + 8, 2, /* N */ + 24, 1, /* mux */ + BIT(31), /* gate */ + 0); + +static SUNXI_CCU_GATE(bus_ce_clk, "bus-ce", "psi-ahb1-ahb2", + 0x68c, BIT(0), 0); + +static const char * const ve_parents[] = { "pll-ve" }; +static SUNXI_CCU_M_WITH_MUX_GATE(ve_clk, "ve", ve_parents, 0x690, + 0, 3, /* M */ + 24, 1, /* mux */ + BIT(31), /* gate */ + CLK_SET_RATE_PARENT); + +static SUNXI_CCU_GATE(bus_ve_clk, "bus-ve", "psi-ahb1-ahb2", + 0x69c, BIT(0), 0); + +static SUNXI_CCU_GATE(bus_dma_clk, "bus-dma", "psi-ahb1-ahb2", + 0x70c, BIT(0), 0); + +static SUNXI_CCU_GATE(bus_msgbox_clk, "bus-msgbox", "psi-ahb1-ahb2", + 0x71c, BIT(0), 0); + +static SUNXI_CCU_GATE(bus_spinlock_clk, "bus-spinlock", "psi-ahb1-ahb2", + 0x72c, BIT(0), 0); + +static SUNXI_CCU_GATE(bus_hstimer_clk, "bus-hstimer", "psi-ahb1-ahb2", + 0x73c, BIT(0), 0); + +static SUNXI_CCU_GATE(avs_clk, "avs", "dcxo24M", 0x740, BIT(31), 0); + +static SUNXI_CCU_GATE(bus_dbg_clk, "bus-dbg", "psi-ahb1-ahb2", + 0x78c, BIT(0), 0); + +static SUNXI_CCU_GATE(bus_psi_clk, "bus-psi", "psi-ahb1-ahb2", + 0x79c, BIT(0), 0); + +static SUNXI_CCU_GATE(bus_pwm_clk, "bus-pwm", "apb1", 0x7ac, BIT(0), 0); + +static SUNXI_CCU_GATE(bus_iommu_clk, "bus-iommu", "apb1", 0x7bc, BIT(0), 0); + +static SUNXI_CCU_GATE(mbus_dma_clk, "mbus-dma", "mbus", + 0x804, BIT(0), 0); +static SUNXI_CCU_GATE(mbus_ve_clk, "mbus-ve", "mbus", + 0x804, BIT(1), 0); +static SUNXI_CCU_GATE(mbus_ce_clk, "mbus-ce", "mbus", + 0x804, BIT(2), 0); +static SUNXI_CCU_GATE(mbus_nand_clk, "mbus-nand", "mbus", + 0x804, BIT(5), 0); +static SUNXI_CCU_GATE(mbus_csi_clk, "mbus-csi", "mbus", + 0x804, BIT(8), 0); +static SUNXI_CCU_GATE(mbus_isp_clk, "mbus-isp", "mbus", + 0x804, BIT(9), 0); +static SUNXI_CCU_GATE(mbus_g2d_clk, "mbus-g2d", "mbus", + 0x804, BIT(10), 0); + +static SUNXI_CCU_GATE(bus_dram_clk, "bus-dram", "psi-ahb1-ahb2", + 0x80c, BIT(0), CLK_IS_CRITICAL); + +static const char * const nand_spi_parents[] = { "dcxo24M", + "pll-periph0", + "pll-periph1", + "pll-periph0-2x", + "pll-periph1-2x" }; +static SUNXI_CCU_MP_WITH_MUX_GATE(nand0_clk, "nand0", nand_spi_parents, 0x810, + 0, 4, /* M */ + 8, 2, /* N */ + 24, 3, /* mux */ + BIT(31), /* gate */ + 0); + +static SUNXI_CCU_MP_WITH_MUX_GATE(nand1_clk, "nand1", nand_spi_parents, 0x814, + 0, 4, /* M */ + 8, 2, /* N */ + 24, 3, /* mux */ + BIT(31), /* gate */ + 0); + +static SUNXI_CCU_GATE(bus_nand_clk, "bus-nand", "ahb3", 0x82c, BIT(0), 0); + +/* don't use postdiv for bsp kernel */ +static const char * const mmc_parents[] = { "dcxo24M", "pll-periph0-2x", + "pll-periph1-2x" }; +static SUNXI_CCU_MP_WITH_MUX_GATE(mmc0_clk, "mmc0", mmc_parents, 0x830, + 0, 4, /* M */ + 8, 2, /* N */ + 24, 2, /* mux */ + BIT(31), /* gate */ + CLK_SET_RATE_NO_REPARENT); + +static SUNXI_CCU_MP_WITH_MUX_GATE(mmc1_clk, "mmc1", mmc_parents, 0x834, + 0, 4, /* M */ + 8, 2, /* N */ + 24, 2, /* mux */ + BIT(31), /* gate */ + CLK_SET_RATE_NO_REPARENT); + +static SUNXI_CCU_MP_WITH_MUX_GATE(mmc2_clk, "mmc2", mmc_parents, 0x838, + 0, 4, /* M */ + 8, 2, /* N */ + 24, 2, /* mux */ + BIT(31), /* gate */ + CLK_SET_RATE_NO_REPARENT); + +static SUNXI_CCU_GATE(bus_mmc0_clk, "bus-mmc0", "ahb3", 0x84c, BIT(0), 0); +static SUNXI_CCU_GATE(bus_mmc1_clk, "bus-mmc1", "ahb3", 0x84c, BIT(1), 0); +static SUNXI_CCU_GATE(bus_mmc2_clk, "bus-mmc2", "ahb3", 0x84c, BIT(2), 0); + +static SUNXI_CCU_GATE(bus_uart0_clk, "bus-uart0", "apb2", 0x90c, BIT(0), 0); +static SUNXI_CCU_GATE(bus_uart1_clk, "bus-uart1", "apb2", 0x90c, BIT(1), 0); +static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2", 0x90c, BIT(2), 0); +static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2", 0x90c, BIT(3), 0); +static SUNXI_CCU_GATE(bus_uart4_clk, "bus-uart4", "apb2", 0x90c, BIT(4), 0); + +static SUNXI_CCU_GATE(bus_i2c0_clk, "bus-i2c0", "apb2", 0x91c, BIT(0), 0); +static SUNXI_CCU_GATE(bus_i2c1_clk, "bus-i2c1", "apb2", 0x91c, BIT(1), 0); +static SUNXI_CCU_GATE(bus_i2c2_clk, "bus-i2c2", "apb2", 0x91c, BIT(2), 0); +static SUNXI_CCU_GATE(bus_i2c3_clk, "bus-i2c3", "apb2", 0x91c, BIT(3), 0); + +static SUNXI_CCU_MP_WITH_MUX_GATE(spi0_clk, "spi0", nand_spi_parents, 0x940, + 0, 4, /* M */ + 8, 2, /* N */ + 24, 3, /* mux */ + BIT(31), /* gate */ + 0); + +static SUNXI_CCU_MP_WITH_MUX_GATE(spi1_clk, "spi1", nand_spi_parents, 0x944, + 0, 4, /* M */ + 8, 2, /* N */ + 24, 3, /* mux */ + BIT(31), /* gate */ + 0); + +static SUNXI_CCU_MP_WITH_MUX_GATE(spi2_clk, "spi2", nand_spi_parents, 0x948, + 0, 4, /* M */ + 8, 2, /* N */ + 24, 3, /* mux */ + BIT(31), /* gate */ + 0); + +static SUNXI_CCU_GATE(bus_spi0_clk, "bus-spi0", "ahb3", 0x96c, BIT(0), 0); +static SUNXI_CCU_GATE(bus_spi1_clk, "bus-spi1", "ahb3", 0x96c, BIT(1), 0); +static SUNXI_CCU_GATE(bus_spi2_clk, "bus-spi2", "ahb3", 0x96c, BIT(2), 0); + +static SUNXI_CCU_GATE(emac_25m_clk, "emac-25m", "ahb3", 0x970, + BIT(31) | BIT(30), 0); + +static SUNXI_CCU_GATE(bus_emac_clk, "bus-emac", "ahb3", 0x97c, BIT(0), 0); + +static const char * const ir_parents[] = { "osc32k", "iosc", + "pll-periph0", "pll-periph1" }; +static SUNXI_CCU_MP_WITH_MUX_GATE(ir_rx_clk, "ir-rx", ir_parents, 0x990, + 0, 4, /* M */ + 8, 2, /* N */ + 24, 3, /* mux */ + BIT(31), /* gate */ + 0); + +static SUNXI_CCU_GATE(bus_ir_rx_clk, "bus-ir-rx", "ahb3", 0x99c, BIT(0), 0); + +static SUNXI_CCU_MP_WITH_MUX_GATE(ir_tx_clk, "ir-tx", ir_parents, 0x9c0, + 0, 4, /* M */ + 8, 2, /* N */ + 24, 3, /* mux */ + BIT(31), /* gate */ + 0); + +static SUNXI_CCU_GATE(bus_ir_tx_clk, "bus-ir-tx", "apb1", 0x9cc, BIT(0), 0); + +static SUNXI_CCU_GATE(bus_gpadc_clk, "bus-gpadc", "apb1", 0x9ec, BIT(0), 0); + +static SUNXI_CCU_GATE(bus_ths_clk, "bus-ths", "apb1", 0x9fc, BIT(0), 0); + +static const char * const audio_parents[] = { "pll-audio", "pll-com-audio" }; +static struct ccu_div i2s0_clk = { + .enable = BIT(31), + .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO), + .mux = _SUNXI_CCU_MUX(24, 2), + .common = { + .reg = 0xa10, + .hw.init = CLK_HW_INIT_PARENTS("i2s0", + audio_parents, + &ccu_div_ops, + CLK_SET_RATE_PARENT), + }, +}; + +static struct ccu_div i2s1_clk = { + .enable = BIT(31), + .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO), + .mux = _SUNXI_CCU_MUX(24, 2), + .common = { + .reg = 0xa14, + .hw.init = CLK_HW_INIT_PARENTS("i2s1", + audio_parents, + &ccu_div_ops, + CLK_SET_RATE_PARENT), + }, +}; + +static struct ccu_div i2s2_clk = { + .enable = BIT(31), + .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO), + .mux = _SUNXI_CCU_MUX(24, 2), + .common = { + .reg = 0xa18, + .hw.init = CLK_HW_INIT_PARENTS("i2s2", + audio_parents, + &ccu_div_ops, + CLK_SET_RATE_PARENT), + }, +}; + +static struct ccu_div i2s3_clk = { + .enable = BIT(31), + .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO), + .mux = _SUNXI_CCU_MUX(24, 2), + .common = { + .reg = 0xa1c, + .hw.init = CLK_HW_INIT_PARENTS("i2s3", + audio_parents, + &ccu_div_ops, + CLK_SET_RATE_PARENT), + }, +}; + +static SUNXI_CCU_GATE(bus_i2s0_clk, "bus-i2s0", "apb1", 0xa20, BIT(0), 0); +static SUNXI_CCU_GATE(bus_i2s1_clk, "bus-i2s1", "apb1", 0xa20, BIT(1), 0); +static SUNXI_CCU_GATE(bus_i2s2_clk, "bus-i2s2", "apb1", 0xa20, BIT(2), 0); +static SUNXI_CCU_GATE(bus_i2s3_clk, "bus-i2s3", "apb1", 0xa20, BIT(3), 0); + +static struct ccu_div spdif_clk = { + .enable = BIT(31), + .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO), + .mux = _SUNXI_CCU_MUX(24, 2), + .common = { + .reg = 0xa24, + .hw.init = CLK_HW_INIT_PARENTS("spdif", + audio_parents, + &ccu_div_ops, + 0), + }, +}; + +static SUNXI_CCU_GATE(bus_spdif_clk, "bus-spdif", "apb1", 0xa2c, BIT(0), 0); + +static struct ccu_div dmic_clk = { + .enable = BIT(31), + .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO), + .mux = _SUNXI_CCU_MUX(24, 2), + .common = { + .reg = 0xa40, + .hw.init = CLK_HW_INIT_PARENTS("dmic", + audio_parents, + &ccu_div_ops, + 0), + }, +}; + +static SUNXI_CCU_GATE(bus_dmic_clk, "bus-dmic", "apb1", 0xa4c, BIT(0), 0); + +static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_dac_clk, "audio-codec-dac", + audio_parents, 0xa50, + 0, 4, /* M */ + 24, 2, /* mux */ + BIT(31), /* gate */ + 0); + +static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_adc_clk, "audio-codec-adc", + audio_parents, 0xa54, + 0, 4, /* M */ + 24, 2, /* mux */ + BIT(31), /* gate */ + 0); + +static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_4x_clk, "audio-codec-4x", + audio_parents, 0xa58, + 0, 4, /* M */ + 24, 2, /* mux */ + BIT(31), /* gate */ + 0); + +static SUNXI_CCU_GATE(bus_audio_codec_clk, "bus-audio-codec", "apb1", 0xa5c, + BIT(0), 0); + +/* + * There are OHCI 12M clock source selection bits for 2 USB 2.0 ports. + * We will force them to 0 (12M divided from 48M). + */ +#define SUN50I_A100_USB0_CLK_REG 0xa70 +#define SUN50I_A100_USB1_CLK_REG 0xa74 + +static SUNXI_CCU_GATE(usb_ohci0_clk, "usb-ohci0", "osc12M", 0xa70, BIT(31), 0); +static SUNXI_CCU_GATE(usb_phy0_clk, "usb-phy0", "dcxo24M", 0xa70, BIT(29), 0); + +static SUNXI_CCU_GATE(usb_ohci1_clk, "usb-ohci1", "osc12M", 0xa74, BIT(31), 0); +static SUNXI_CCU_GATE(usb_phy1_clk, "usb-phy1", "dcxo24M", 0xa74, BIT(29), 0); + +static SUNXI_CCU_GATE(bus_ohci0_clk, "bus-ohci0", "ahb3", 0xa8c, BIT(0), 0); +static SUNXI_CCU_GATE(bus_ohci1_clk, "bus-ohci1", "ahb3", 0xa8c, BIT(1), 0); +static SUNXI_CCU_GATE(bus_ehci0_clk, "bus-ehci0", "ahb3", 0xa8c, BIT(4), 0); +static SUNXI_CCU_GATE(bus_ehci1_clk, "bus-ehci1", "ahb3", 0xa8c, BIT(5), 0); +static SUNXI_CCU_GATE(bus_otg_clk, "bus-otg", "ahb3", 0xa8c, BIT(8), 0); + +static SUNXI_CCU_GATE(bus_lradc_clk, "bus-lradc", "ahb3", 0xa9c, BIT(0), 0); + +static SUNXI_CCU_GATE(bus_dpss_top0_clk, "bus-dpss-top0", "ahb3", + 0xabc, BIT(0), 0); + +static SUNXI_CCU_GATE(bus_dpss_top1_clk, "bus-dpss-top1", "ahb3", + 0xacc, BIT(0), 0); + +static const char * const mipi_dsi_parents[] = { "dcxo24M", "pll-periph0-2x", + "pll-periph0" }; +static SUNXI_CCU_M_WITH_MUX_GATE(mipi_dsi_clk, "mipi-dsi", + mipi_dsi_parents, + 0xb24, + 0, 4, /* M */ + 24, 2, /* mux */ + BIT(31), /* gate */ + 0); + +static SUNXI_CCU_GATE(bus_mipi_dsi_clk, "bus-mipi-dsi", "ahb3", + 0xb4c, BIT(0), 0); + +static const char * const tcon_lcd_parents[] = { "pll-video0-4x", + "pll-video1-4x", + "pll-video2-4x", + "pll-video3-4x", + "pll-periph0-2x" }; +static SUNXI_CCU_MP_WITH_MUX_GATE(tcon_lcd_clk, "tcon-lcd0", + tcon_lcd_parents, 0xb60, + 0, 4, /* M */ + 8, 2, /* N */ + 24, 3, /* mux */ + BIT(31), /* gate */ + 0); + +static SUNXI_CCU_GATE(bus_tcon_lcd_clk, "bus-tcon-lcd0", "ahb3", + 0xb7c, BIT(0), 0); + +static const char * const ledc_parents[] = { "dcxo24M", + "pll-periph0" }; +static SUNXI_CCU_MP_WITH_MUX_GATE(ledc_clk, "ledc", + ledc_parents, 0xbf0, + 0, 4, /* M */ + 8, 2, /* N */ + 24, 3, /* mux */ + BIT(31), /* gate */ + 0); + +static SUNXI_CCU_GATE(bus_ledc_clk, "bus-ledc", "ahb3", 0xbfc, BIT(0), 0); + +static const char * const csi_top_parents[] = { "pll-periph0-2x", + "pll-video0-2x", + "pll-video1-2x", + "pll-video2-2x", + "pll-video3-2x" }; +static SUNXI_CCU_M_WITH_MUX_GATE(csi_top_clk, "csi-top", + csi_top_parents, 0xc04, + 0, 4, /* M */ + 24, 3, /* mux */ + BIT(31), /* gate */ + 0); + +static const char * const csi0_mclk_parents[] = { "dcxo24M", "pll-video2", + "pll-video3", "pll-video0", + "pll-video1" }; +static SUNXI_CCU_M_WITH_MUX_GATE(csi0_mclk_clk, "csi0-mclk", + csi0_mclk_parents, 0xc08, + 0, 5, /* M */ + 24, 3, /* mux */ + BIT(31), /* gate */ + 0); + +static const char * const csi1_mclk_parents[] = { "dcxo24M", "pll-video3", + "pll-video0", "pll-video1", + "pll-video2" }; +static SUNXI_CCU_M_WITH_MUX_GATE(csi1_mclk_clk, "csi1-mclk", + csi1_mclk_parents, 0xc0c, + 0, 5, /* M */ + 24, 3, /* mux */ + BIT(31), /* gate */ + 0); + +static SUNXI_CCU_GATE(bus_csi_clk, "bus-csi", "ahb3", 0xc1c, BIT(0), 0); + +static const char * const csi_isp_parents[] = { "pll-periph0-2x", + "pll-video0-2x", + "pll-video1-2x", + "pll-video2-2x", + "pll-video3-2x" }; +static SUNXI_CCU_M_WITH_MUX_GATE(csi_isp_clk, "csi-isp", + csi_isp_parents, 0xc20, + 0, 5, /* M */ + 24, 3, /* mux */ + BIT(31), /* gate */ + 0); + +/* Fixed factor clocks */ +static CLK_FIXED_FACTOR_FW_NAME(osc12M_clk, "osc12M", "hosc", 2, 1, 0); + +static CLK_FIXED_FACTOR_HW(pll_com_audio_clk, "pll-com-audio", + &pll_com_clk.common.hw, + 5, 1, CLK_SET_RATE_PARENT); + +static CLK_FIXED_FACTOR_HW(pll_periph0_2x_clk, "pll-periph0-2x", + &pll_periph0_clk.common.hw, + 1, 2, 0); + +static CLK_FIXED_FACTOR_HW(pll_periph1_2x_clk, "pll-periph1-2x", + &pll_periph1_clk.common.hw, + 1, 2, 0); + +static const struct clk_hw *pll_video0_parents[] = { + &pll_video0_clk.common.hw +}; +static CLK_FIXED_FACTOR_HWS(pll_video0_4x_clk, "pll-video0-4x", + pll_video0_parents, + 1, 4, CLK_SET_RATE_PARENT); +static CLK_FIXED_FACTOR_HWS(pll_video0_2x_clk, "pll-video0-2x", + pll_video0_parents, + 1, 2, CLK_SET_RATE_PARENT); + +static const struct clk_hw *pll_video1_parents[] = { + &pll_video1_clk.common.hw +}; +static CLK_FIXED_FACTOR_HWS(pll_video1_4x_clk, "pll-video1-4x", + pll_video1_parents, + 1, 4, CLK_SET_RATE_PARENT); +static CLK_FIXED_FACTOR_HWS(pll_video1_2x_clk, "pll-video1-2x", + pll_video1_parents, + 1, 2, CLK_SET_RATE_PARENT); + +static const struct clk_hw *pll_video2_parents[] = { + &pll_video2_clk.common.hw +}; +static CLK_FIXED_FACTOR_HWS(pll_video2_4x_clk, "pll-video2-4x", + pll_video2_parents, + 1, 4, CLK_SET_RATE_PARENT); +static CLK_FIXED_FACTOR_HWS(pll_video2_2x_clk, "pll-video2-2x", + pll_video2_parents, + 1, 2, CLK_SET_RATE_PARENT); + +static const struct clk_hw *pll_video3_parents[] = { + &pll_video3_clk.common.hw +}; +static CLK_FIXED_FACTOR_HWS(pll_video3_4x_clk, "pll-video3-4x", + pll_video3_parents, + 1, 4, CLK_SET_RATE_PARENT); +static CLK_FIXED_FACTOR_HWS(pll_video3_2x_clk, "pll-video3-2x", + pll_video3_parents, + 1, 2, CLK_SET_RATE_PARENT); + +static struct ccu_common *sun50i_a100_ccu_clks[] = { + &pll_cpux_clk.common, + &pll_ddr0_clk.common, + &pll_periph0_clk.common, + &pll_periph1_clk.common, + &pll_gpu_clk.common, + &pll_video0_clk.common, + &pll_video1_clk.common, + &pll_video2_clk.common, + &pll_video3_clk.common, + &pll_ve_clk.common, + &pll_com_clk.common, + &pll_audio_clk.common, + &cpux_clk.common, + &axi_clk.common, + &cpux_apb_clk.common, + &psi_ahb1_ahb2_clk.common, + &ahb3_clk.common, + &apb1_clk.common, + &apb2_clk.common, + &mbus_clk.common, + &de_clk.common, + &bus_de_clk.common, + &g2d_clk.common, + &bus_g2d_clk.common, + &gpu_clk.common, + &bus_gpu_clk.common, + &ce_clk.common, + &bus_ce_clk.common, + &ve_clk.common, + &bus_ve_clk.common, + &bus_dma_clk.common, + &bus_msgbox_clk.common, + &bus_spinlock_clk.common, + &bus_hstimer_clk.common, + &avs_clk.common, + &bus_dbg_clk.common, + &bus_psi_clk.common, + &bus_pwm_clk.common, + &bus_iommu_clk.common, + &mbus_dma_clk.common, + &mbus_ve_clk.common, + &mbus_ce_clk.common, + &mbus_nand_clk.common, + &mbus_csi_clk.common, + &mbus_isp_clk.common, + &mbus_g2d_clk.common, + &bus_dram_clk.common, + &nand0_clk.common, + &nand1_clk.common, + &bus_nand_clk.common, + &mmc0_clk.common, + &mmc1_clk.common, + &mmc2_clk.common, + &bus_mmc0_clk.common, + &bus_mmc1_clk.common, + &bus_mmc2_clk.common, + &bus_uart0_clk.common, + &bus_uart1_clk.common, + &bus_uart2_clk.common, + &bus_uart3_clk.common, + &bus_uart4_clk.common, + &bus_i2c0_clk.common, + &bus_i2c1_clk.common, + &bus_i2c2_clk.common, + &bus_i2c3_clk.common, + &spi0_clk.common, + &spi1_clk.common, + &spi2_clk.common, + &bus_spi0_clk.common, + &bus_spi1_clk.common, + &bus_spi2_clk.common, + &emac_25m_clk.common, + &bus_emac_clk.common, + &ir_rx_clk.common, + &bus_ir_rx_clk.common, + &ir_tx_clk.common, + &bus_ir_tx_clk.common, + &bus_gpadc_clk.common, + &bus_ths_clk.common, + &i2s0_clk.common, + &i2s1_clk.common, + &i2s2_clk.common, + &i2s3_clk.common, + &bus_i2s0_clk.common, + &bus_i2s1_clk.common, + &bus_i2s2_clk.common, + &bus_i2s3_clk.common, + &spdif_clk.common, + &bus_spdif_clk.common, + &dmic_clk.common, + &bus_dmic_clk.common, + &audio_codec_dac_clk.common, + &audio_codec_adc_clk.common, + &audio_codec_4x_clk.common, + &bus_audio_codec_clk.common, + &usb_ohci0_clk.common, + &usb_phy0_clk.common, + &usb_ohci1_clk.common, + &usb_phy1_clk.common, + &bus_ohci0_clk.common, + &bus_ohci1_clk.common, + &bus_ehci0_clk.common, + &bus_ehci1_clk.common, + &bus_otg_clk.common, + &bus_lradc_clk.common, + &bus_dpss_top0_clk.common, + &bus_dpss_top1_clk.common, + &mipi_dsi_clk.common, + &bus_mipi_dsi_clk.common, + &tcon_lcd_clk.common, + &bus_tcon_lcd_clk.common, + &ledc_clk.common, + &bus_ledc_clk.common, + &csi_top_clk.common, + &csi0_mclk_clk.common, + &csi1_mclk_clk.common, + &bus_csi_clk.common, + &csi_isp_clk.common, +}; + +static struct clk_hw_onecell_data sun50i_a100_hw_clks = { + .hws = { + [CLK_OSC12M] = &osc12M_clk.hw, + [CLK_PLL_CPUX] = &pll_cpux_clk.common.hw, + [CLK_PLL_DDR0] = &pll_ddr0_clk.common.hw, + [CLK_PLL_PERIPH0] = &pll_periph0_clk.common.hw, + [CLK_PLL_PERIPH0_2X] = &pll_periph0_2x_clk.hw, + [CLK_PLL_PERIPH1] = &pll_periph1_clk.common.hw, + [CLK_PLL_PERIPH1_2X] = &pll_periph1_2x_clk.hw, + [CLK_PLL_GPU] = &pll_gpu_clk.common.hw, + [CLK_PLL_VIDEO0] = &pll_video0_clk.common.hw, + [CLK_PLL_VIDEO0_2X] = &pll_video0_2x_clk.hw, + [CLK_PLL_VIDEO0_4X] = &pll_video0_4x_clk.hw, + [CLK_PLL_VIDEO1] = &pll_video1_clk.common.hw, + [CLK_PLL_VIDEO1_2X] = &pll_video1_2x_clk.hw, + [CLK_PLL_VIDEO1_4X] = &pll_video1_4x_clk.hw, + [CLK_PLL_VIDEO2] = &pll_video2_clk.common.hw, + [CLK_PLL_VIDEO2_2X] = &pll_video2_2x_clk.hw, + [CLK_PLL_VIDEO2_4X] = &pll_video2_4x_clk.hw, + [CLK_PLL_VIDEO3] = &pll_video3_clk.common.hw, + [CLK_PLL_VIDEO3_2X] = &pll_video3_2x_clk.hw, + [CLK_PLL_VIDEO3_4X] = &pll_video3_4x_clk.hw, + [CLK_PLL_VE] = &pll_ve_clk.common.hw, + [CLK_PLL_COM] = &pll_com_clk.common.hw, + [CLK_PLL_COM_AUDIO] = &pll_com_audio_clk.hw, + [CLK_PLL_AUDIO] = &pll_audio_clk.common.hw, + [CLK_CPUX] = &cpux_clk.common.hw, + [CLK_AXI] = &axi_clk.common.hw, + [CLK_CPUX_APB] = &cpux_apb_clk.common.hw, + [CLK_PSI_AHB1_AHB2] = &psi_ahb1_ahb2_clk.common.hw, + [CLK_AHB3] = &ahb3_clk.common.hw, + [CLK_APB1] = &apb1_clk.common.hw, + [CLK_APB2] = &apb2_clk.common.hw, + [CLK_MBUS] = &mbus_clk.common.hw, + [CLK_DE] = &de_clk.common.hw, + [CLK_BUS_DE] = &bus_de_clk.common.hw, + [CLK_G2D] = &g2d_clk.common.hw, + [CLK_BUS_G2D] = &bus_g2d_clk.common.hw, + [CLK_GPU] = &gpu_clk.common.hw, + [CLK_BUS_GPU] = &bus_gpu_clk.common.hw, + [CLK_CE] = &ce_clk.common.hw, + [CLK_BUS_CE] = &bus_ce_clk.common.hw, + [CLK_VE] = &ve_clk.common.hw, + [CLK_BUS_VE] = &bus_ve_clk.common.hw, + [CLK_BUS_DMA] = &bus_dma_clk.common.hw, + [CLK_BUS_MSGBOX] = &bus_msgbox_clk.common.hw, + [CLK_BUS_SPINLOCK] = &bus_spinlock_clk.common.hw, + [CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw, + [CLK_AVS] = &avs_clk.common.hw, + [CLK_BUS_DBG] = &bus_dbg_clk.common.hw, + [CLK_BUS_PSI] = &bus_psi_clk.common.hw, + [CLK_BUS_PWM] = &bus_pwm_clk.common.hw, + [CLK_BUS_IOMMU] = &bus_iommu_clk.common.hw, + [CLK_MBUS_DMA] = &mbus_dma_clk.common.hw, + [CLK_MBUS_VE] = &mbus_ve_clk.common.hw, + [CLK_MBUS_CE] = &mbus_ce_clk.common.hw, + [CLK_MBUS_NAND] = &mbus_nand_clk.common.hw, + [CLK_MBUS_CSI] = &mbus_csi_clk.common.hw, + [CLK_MBUS_ISP] = &mbus_isp_clk.common.hw, + [CLK_MBUS_G2D] = &mbus_g2d_clk.common.hw, + [CLK_BUS_DRAM] = &bus_dram_clk.common.hw, + [CLK_NAND0] = &nand0_clk.common.hw, + [CLK_NAND1] = &nand1_clk.common.hw, + [CLK_BUS_NAND] = &bus_nand_clk.common.hw, + [CLK_MMC0] = &mmc0_clk.common.hw, + [CLK_MMC1] = &mmc1_clk.common.hw, + [CLK_MMC2] = &mmc2_clk.common.hw, + [CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw, + [CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw, + [CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw, + [CLK_BUS_UART0] = &bus_uart0_clk.common.hw, + [CLK_BUS_UART1] = &bus_uart1_clk.common.hw, + [CLK_BUS_UART2] = &bus_uart2_clk.common.hw, + [CLK_BUS_UART3] = &bus_uart3_clk.common.hw, + [CLK_BUS_UART4] = &bus_uart4_clk.common.hw, + [CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw, + [CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw, + [CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw, + [CLK_BUS_I2C3] = &bus_i2c3_clk.common.hw, + [CLK_SPI0] = &spi0_clk.common.hw, + [CLK_SPI1] = &spi1_clk.common.hw, + [CLK_SPI2] = &spi2_clk.common.hw, + [CLK_BUS_SPI0] = &bus_spi0_clk.common.hw, + [CLK_BUS_SPI1] = &bus_spi1_clk.common.hw, + [CLK_BUS_SPI2] = &bus_spi2_clk.common.hw, + [CLK_EMAC_25M] = &emac_25m_clk.common.hw, + [CLK_BUS_EMAC] = &bus_emac_clk.common.hw, + [CLK_IR_RX] = &ir_rx_clk.common.hw, + [CLK_BUS_IR_RX] = &bus_ir_rx_clk.common.hw, + [CLK_IR_TX] = &ir_tx_clk.common.hw, + [CLK_BUS_IR_TX] = &bus_ir_tx_clk.common.hw, + [CLK_BUS_GPADC] = &bus_gpadc_clk.common.hw, + [CLK_BUS_THS] = &bus_ths_clk.common.hw, + [CLK_I2S0] = &i2s0_clk.common.hw, + [CLK_I2S1] = &i2s1_clk.common.hw, + [CLK_I2S2] = &i2s2_clk.common.hw, + [CLK_I2S3] = &i2s3_clk.common.hw, + [CLK_BUS_I2S0] = &bus_i2s0_clk.common.hw, + [CLK_BUS_I2S1] = &bus_i2s1_clk.common.hw, + [CLK_BUS_I2S2] = &bus_i2s2_clk.common.hw, + [CLK_BUS_I2S3] = &bus_i2s3_clk.common.hw, + [CLK_SPDIF] = &spdif_clk.common.hw, + [CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw, + [CLK_DMIC] = &dmic_clk.common.hw, + [CLK_BUS_DMIC] = &bus_dmic_clk.common.hw, + [CLK_AUDIO_DAC] = &audio_codec_dac_clk.common.hw, + [CLK_AUDIO_ADC] = &audio_codec_adc_clk.common.hw, + [CLK_AUDIO_4X] = &audio_codec_4x_clk.common.hw, + [CLK_BUS_AUDIO_CODEC] = &bus_audio_codec_clk.common.hw, + [CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw, + [CLK_USB_PHY0] = &usb_phy0_clk.common.hw, + [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw, + [CLK_USB_PHY1] = &usb_phy1_clk.common.hw, + [CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw, + [CLK_BUS_OHCI1] = &bus_ohci1_clk.common.hw, + [CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw, + [CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw, + [CLK_BUS_OTG] = &bus_otg_clk.common.hw, + [CLK_BUS_LRADC] = &bus_lradc_clk.common.hw, + [CLK_BUS_DPSS_TOP0] = &bus_dpss_top0_clk.common.hw, + [CLK_BUS_DPSS_TOP1] = &bus_dpss_top1_clk.common.hw, + [CLK_MIPI_DSI] = &mipi_dsi_clk.common.hw, + [CLK_BUS_MIPI_DSI] = &bus_mipi_dsi_clk.common.hw, + [CLK_TCON_LCD] = &tcon_lcd_clk.common.hw, + [CLK_BUS_TCON_LCD] = &bus_tcon_lcd_clk.common.hw, + [CLK_LEDC] = &ledc_clk.common.hw, + [CLK_BUS_LEDC] = &bus_ledc_clk.common.hw, + [CLK_CSI_TOP] = &csi_top_clk.common.hw, + [CLK_CSI0_MCLK] = &csi0_mclk_clk.common.hw, + [CLK_CSI1_MCLK] = &csi1_mclk_clk.common.hw, + [CLK_BUS_CSI] = &bus_csi_clk.common.hw, + [CLK_CSI_ISP] = &csi_isp_clk.common.hw, + }, + .num = CLK_NUMBER, +}; + +static struct ccu_reset_map sun50i_a100_ccu_resets[] = { + [RST_MBUS] = { 0x540, BIT(30) }, + + [RST_BUS_DE] = { 0x60c, BIT(16) }, + [RST_BUS_G2D] = { 0x63c, BIT(16) }, + [RST_BUS_GPU] = { 0x67c, BIT(16) }, + [RST_BUS_CE] = { 0x68c, BIT(16) }, + [RST_BUS_VE] = { 0x69c, BIT(16) }, + [RST_BUS_DMA] = { 0x70c, BIT(16) }, + [RST_BUS_MSGBOX] = { 0x71c, BIT(16) }, + [RST_BUS_SPINLOCK] = { 0x72c, BIT(16) }, + [RST_BUS_HSTIMER] = { 0x73c, BIT(16) }, + [RST_BUS_DBG] = { 0x78c, BIT(16) }, + [RST_BUS_PSI] = { 0x79c, BIT(16) }, + [RST_BUS_PWM] = { 0x7ac, BIT(16) }, + [RST_BUS_DRAM] = { 0x80c, BIT(16) }, + [RST_BUS_NAND] = { 0x82c, BIT(16) }, + [RST_BUS_MMC0] = { 0x84c, BIT(16) }, + [RST_BUS_MMC1] = { 0x84c, BIT(17) }, + [RST_BUS_MMC2] = { 0x84c, BIT(18) }, + [RST_BUS_UART0] = { 0x90c, BIT(16) }, + [RST_BUS_UART1] = { 0x90c, BIT(17) }, + [RST_BUS_UART2] = { 0x90c, BIT(18) }, + [RST_BUS_UART3] = { 0x90c, BIT(19) }, + [RST_BUS_UART4] = { 0x90c, BIT(20) }, + [RST_BUS_I2C0] = { 0x91c, BIT(16) }, + [RST_BUS_I2C1] = { 0x91c, BIT(17) }, + [RST_BUS_I2C2] = { 0x91c, BIT(18) }, + [RST_BUS_I2C3] = { 0x91c, BIT(19) }, + [RST_BUS_SPI0] = { 0x96c, BIT(16) }, + [RST_BUS_SPI1] = { 0x96c, BIT(17) }, + [RST_BUS_SPI2] = { 0x96c, BIT(18) }, + [RST_BUS_EMAC] = { 0x97c, BIT(16) }, + [RST_BUS_IR_RX] = { 0x99c, BIT(16) }, + [RST_BUS_IR_TX] = { 0x9cc, BIT(16) }, + [RST_BUS_GPADC] = { 0x9ec, BIT(16) }, + [RST_BUS_THS] = { 0x9fc, BIT(16) }, + [RST_BUS_I2S0] = { 0xa20, BIT(16) }, + [RST_BUS_I2S1] = { 0xa20, BIT(17) }, + [RST_BUS_I2S2] = { 0xa20, BIT(18) }, + [RST_BUS_I2S3] = { 0xa20, BIT(19) }, + [RST_BUS_SPDIF] = { 0xa2c, BIT(16) }, + [RST_BUS_DMIC] = { 0xa4c, BIT(16) }, + [RST_BUS_AUDIO_CODEC] = { 0xa5c, BIT(16) }, + + [RST_USB_PHY0] = { 0xa70, BIT(30) }, + [RST_USB_PHY1] = { 0xa74, BIT(30) }, + + [RST_BUS_OHCI0] = { 0xa8c, BIT(16) }, + [RST_BUS_OHCI1] = { 0xa8c, BIT(17) }, + [RST_BUS_EHCI0] = { 0xa8c, BIT(20) }, + [RST_BUS_EHCI1] = { 0xa8c, BIT(21) }, + [RST_BUS_OTG] = { 0xa8c, BIT(24) }, + + [RST_BUS_LRADC] = { 0xa9c, BIT(16) }, + [RST_BUS_DPSS_TOP0] = { 0xabc, BIT(16) }, + [RST_BUS_DPSS_TOP1] = { 0xacc, BIT(16) }, + [RST_BUS_MIPI_DSI] = { 0xb4c, BIT(16) }, + [RST_BUS_TCON_LCD] = { 0xb7c, BIT(16) }, + [RST_BUS_LVDS] = { 0xbac, BIT(16) }, + [RST_BUS_LEDC] = { 0xbfc, BIT(16) }, + [RST_BUS_CSI] = { 0xc1c, BIT(16) }, + [RST_BUS_CSI_ISP] = { 0xc2c, BIT(16) }, +}; + +static const struct sunxi_ccu_desc sun50i_a100_ccu_desc = { + .ccu_clks = sun50i_a100_ccu_clks, + .num_ccu_clks = ARRAY_SIZE(sun50i_a100_ccu_clks), + + .hw_clks = &sun50i_a100_hw_clks, + + .resets = sun50i_a100_ccu_resets, + .num_resets = ARRAY_SIZE(sun50i_a100_ccu_resets), +}; + +static const u32 pll_regs[] = { + SUN50I_A100_PLL_CPUX_REG, + SUN50I_A100_PLL_DDR0_REG, + SUN50I_A100_PLL_PERIPH0_REG, + SUN50I_A100_PLL_PERIPH1_REG, + SUN50I_A100_PLL_GPU_REG, + SUN50I_A100_PLL_VIDEO0_REG, + SUN50I_A100_PLL_VIDEO1_REG, + SUN50I_A100_PLL_VIDEO2_REG, + SUN50I_A100_PLL_VIDEO3_REG, + SUN50I_A100_PLL_VE_REG, + SUN50I_A100_PLL_COM_REG, + SUN50I_A100_PLL_AUDIO_REG, +}; + +static const u32 pll_video_regs[] = { + SUN50I_A100_PLL_VIDEO0_REG, + SUN50I_A100_PLL_VIDEO1_REG, + SUN50I_A100_PLL_VIDEO2_REG, + SUN50I_A100_PLL_VIDEO3_REG, +}; + +static const u32 usb2_clk_regs[] = { + SUN50I_A100_USB0_CLK_REG, + SUN50I_A100_USB1_CLK_REG, +}; + +static struct ccu_pll_nb sun50i_a100_pll_cpu_nb = { + .common = &pll_cpux_clk.common, + /* copy from pll_cpux_clk */ + .enable = BIT(27), + .lock = BIT(28), +}; + +static struct ccu_mux_nb sun50i_a100_cpu_nb = { + .common = &cpux_clk.common, + .cm = &cpux_clk.mux, + .delay_us = 1, + .bypass_index = 4, /* index of pll periph0 */ +}; + +static int sun50i_a100_ccu_probe(struct platform_device *pdev) +{ + void __iomem *reg; + u32 val; + int i, ret; + + reg = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(reg)) + return PTR_ERR(reg); + + /* Enable the lock bits on all PLLs */ + for (i = 0; i < ARRAY_SIZE(pll_regs); i++) { + val = readl(reg + pll_regs[i]); + val |= BIT(29); + writel(val, reg + pll_regs[i]); + } + + /* + * In order to pass the EMI certification, the SDM function of + * the peripheral 1 bus is enabled, and the frequency is still + * calculated using the previous division factor. + */ + writel(0xd1303333, reg + SUN50I_A100_PLL_PERIPH1_PATTERN0_REG); + + val = readl(reg + SUN50I_A100_PLL_PERIPH1_REG); + val |= BIT(24); + writel(val, reg + SUN50I_A100_PLL_PERIPH1_REG); + + /* + * Force the output divider of video PLLs to 0. + * + * See the comment before pll-video0 definition for the reason. + */ + for (i = 0; i < ARRAY_SIZE(pll_video_regs); i++) { + val = readl(reg + pll_video_regs[i]); + val &= ~BIT(0); + writel(val, reg + pll_video_regs[i]); + } + + /* Enforce m1 = 0, m0 = 1 for Audio PLL */ + val = readl(reg + SUN50I_A100_PLL_AUDIO_REG); + val &= ~BIT(1); + val |= BIT(0); + writel(val, reg + SUN50I_A100_PLL_AUDIO_REG); + + /* + * Force OHCI 12M clock sources to 00 (12MHz divided from 48MHz) + * + * This clock mux is still mysterious, and the code just enforces + * it to have a valid clock parent. + */ + for (i = 0; i < ARRAY_SIZE(usb2_clk_regs); i++) { + val = readl(reg + usb2_clk_regs[i]); + val &= ~GENMASK(25, 24); + writel(val, reg + usb2_clk_regs[i]); + } + + ret = sunxi_ccu_probe(pdev->dev.of_node, reg, &sun50i_a100_ccu_desc); + if (ret) + return ret; + + /* Gate then ungate PLL CPU after any rate changes */ + ccu_pll_notifier_register(&sun50i_a100_pll_cpu_nb); + + /* Reparent CPU during PLL CPU rate changes */ + ccu_mux_notifier_register(pll_cpux_clk.common.hw.clk, + &sun50i_a100_cpu_nb); + + return 0; +} + +static const struct of_device_id sun50i_a100_ccu_ids[] = { + { .compatible = "allwinner,sun50i-a100-ccu" }, + { } +}; + +static struct platform_driver sun50i_a100_ccu_driver = { + .probe = sun50i_a100_ccu_probe, + .driver = { + .name = "sun50i-a100-ccu", + .of_match_table = sun50i_a100_ccu_ids, + }, +}; +module_platform_driver(sun50i_a100_ccu_driver); diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100.h b/drivers/clk/sunxi-ng/ccu-sun50i-a100.h new file mode 100644 index 000000000000..4fbf2e1a6697 --- /dev/null +++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100.h @@ -0,0 +1,14 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (c) 2020 Frank Lee <frank@allwinner.com> + */ + +#ifndef _CCU_SUN50I_A100_H_ +#define _CCU_SUN50I_A100_H_ + +#include <dt-bindings/clock/sun50i-a100-ccu.h> +#include <dt-bindings/reset/sun50i-a100-ccu.h> + +#define CLK_NUMBER (CLK_CSI_ISP + 1) + +#endif /* _CCU_SUN50I_A100_H_ */ diff --git a/include/dt-bindings/clock/sun50i-a100-ccu.h b/include/dt-bindings/clock/sun50i-a100-ccu.h new file mode 100644 index 000000000000..8186b1a7bcfe --- /dev/null +++ b/include/dt-bindings/clock/sun50i-a100-ccu.h @@ -0,0 +1,141 @@ +/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */ +/* + * Copyright (c) 2020 Frank Lee <frank@allwinner.com> + */ + +#ifndef _DT_BINDINGS_CLK_SUN50I_A100_H_ +#define _DT_BINDINGS_CLK_SUN50I_A100_H_ + +#define CLK_OSC12M 0 +#define CLK_PLL_CPUX 1 +#define CLK_PLL_DDR0 2 +#define CLK_PLL_PERIPH0 3 +#define CLK_PLL_PERIPH0_2X 4 +#define CLK_PLL_PERIPH1 5 +#define CLK_PLL_PERIPH1_2X 6 +#define CLK_PLL_GPU 7 +#define CLK_PLL_VIDEO0 8 +#define CLK_PLL_VIDEO0_2X 9 +#define CLK_PLL_VIDEO0_4X 10 +#define CLK_PLL_VIDEO1 11 +#define CLK_PLL_VIDEO1_2X 12 +#define CLK_PLL_VIDEO1_4X 13 +#define CLK_PLL_VIDEO2 14 +#define CLK_PLL_VIDEO2_2X 15 +#define CLK_PLL_VIDEO2_4X 16 +#define CLK_PLL_VIDEO3 17 +#define CLK_PLL_VIDEO3_2X 18 +#define CLK_PLL_VIDEO3_4X 19 +#define CLK_PLL_VE 20 +#define CLK_PLL_COM 21 +#define CLK_PLL_COM_AUDIO 22 +#define CLK_PLL_AUDIO 23 +#define CLK_CPUX 24 +#define CLK_AXI 25 +#define CLK_CPUX_APB 26 +#define CLK_PSI_AHB1_AHB2 27 +#define CLK_AHB3 28 +#define CLK_APB1 29 +#define CLK_APB2 30 +#define CLK_MBUS 31 +#define CLK_DE 32 +#define CLK_BUS_DE 33 +#define CLK_G2D 34 +#define CLK_BUS_G2D 35 +#define CLK_GPU 36 +#define CLK_BUS_GPU 37 +#define CLK_CE 38 +#define CLK_BUS_CE 39 +#define CLK_VE 40 +#define CLK_BUS_VE 41 +#define CLK_BUS_DMA 42 +#define CLK_BUS_MSGBOX 43 +#define CLK_BUS_SPINLOCK 44 +#define CLK_BUS_HSTIMER 45 +#define CLK_AVS 46 +#define CLK_BUS_DBG 47 +#define CLK_BUS_PSI 48 +#define CLK_BUS_PWM 49 +#define CLK_BUS_IOMMU 50 +#define CLK_MBUS_DMA 51 +#define CLK_MBUS_VE 52 +#define CLK_MBUS_CE 53 +#define CLK_MBUS_NAND 54 +#define CLK_MBUS_CSI 55 +#define CLK_MBUS_ISP 56 +#define CLK_MBUS_G2D 57 +#define CLK_BUS_DRAM 58 +#define CLK_NAND0 59 +#define CLK_NAND1 60 +#define CLK_BUS_NAND 61 +#define CLK_MMC0 62 +#define CLK_MMC1 63 +#define CLK_MMC2 64 +#define CLK_MMC3 65 +#define CLK_BUS_MMC0 66 +#define CLK_BUS_MMC1 67 +#define CLK_BUS_MMC2 68 +#define CLK_BUS_UART0 69 +#define CLK_BUS_UART1 70 +#define CLK_BUS_UART2 71 +#define CLK_BUS_UART3 72 +#define CLK_BUS_UART4 73 +#define CLK_BUS_I2C0 74 +#define CLK_BUS_I2C1 75 +#define CLK_BUS_I2C2 76 +#define CLK_BUS_I2C3 77 +#define CLK_SPI0 78 +#define CLK_SPI1 79 +#define CLK_SPI2 80 +#define CLK_BUS_SPI0 81 +#define CLK_BUS_SPI1 82 +#define CLK_BUS_SPI2 83 +#define CLK_EMAC_25M 84 +#define CLK_BUS_EMAC 85 +#define CLK_IR_RX 86 +#define CLK_BUS_IR_RX 87 +#define CLK_IR_TX 88 +#define CLK_BUS_IR_TX 89 +#define CLK_BUS_GPADC 90 +#define CLK_BUS_THS 91 +#define CLK_I2S0 92 +#define CLK_I2S1 93 +#define CLK_I2S2 94 +#define CLK_I2S3 95 +#define CLK_BUS_I2S0 96 +#define CLK_BUS_I2S1 97 +#define CLK_BUS_I2S2 98 +#define CLK_BUS_I2S3 99 +#define CLK_SPDIF 100 +#define CLK_BUS_SPDIF 101 +#define CLK_DMIC 102 +#define CLK_BUS_DMIC 103 +#define CLK_AUDIO_DAC 104 +#define CLK_AUDIO_ADC 105 +#define CLK_AUDIO_4X 106 +#define CLK_BUS_AUDIO_CODEC 107 +#define CLK_USB_OHCI0 108 +#define CLK_USB_PHY0 109 +#define CLK_USB_OHCI1 110 +#define CLK_USB_PHY1 111 +#define CLK_BUS_OHCI0 112 +#define CLK_BUS_OHCI1 113 +#define CLK_BUS_EHCI0 114 +#define CLK_BUS_EHCI1 115 +#define CLK_BUS_OTG 116 +#define CLK_BUS_LRADC 117 +#define CLK_BUS_DPSS_TOP0 118 +#define CLK_BUS_DPSS_TOP1 119 +#define CLK_MIPI_DSI 120 +#define CLK_BUS_MIPI_DSI 121 +#define CLK_TCON_LCD 122 +#define CLK_BUS_TCON_LCD 123 +#define CLK_LEDC 124 +#define CLK_BUS_LEDC 125 +#define CLK_CSI_TOP 126 +#define CLK_CSI0_MCLK 127 +#define CLK_CSI1_MCLK 128 +#define CLK_BUS_CSI 129 +#define CLK_CSI_ISP 130 + +#endif /* _DT_BINDINGS_CLK_SUN50I_A100_H_ */ diff --git a/include/dt-bindings/clock/sun50i-a100-r-ccu.h b/include/dt-bindings/clock/sun50i-a100-r-ccu.h new file mode 100644 index 000000000000..a4486c31924a --- /dev/null +++ b/include/dt-bindings/clock/sun50i-a100-r-ccu.h @@ -0,0 +1,25 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (c) 2020 Frank Lee <frank@allwinner.com> + */ + +#ifndef _DT_BINDINGS_CLK_SUN50I_A100_R_CCU_H_ +#define _DT_BINDINGS_CLK_SUN50I_A100_R_CCU_H_ + +#define CLK_CPUS 0 +#define CLK_R_AHB 1 +#define CLK_R_APB1 2 +#define CLK_R_APB2 3 +#define CLK_R_APB1_TIMER 4 +#define CLK_R_APB1_TWD 5 +#define CLK_R_APB1_PWM 6 +#define CLK_R_APB1_BUS_PWM 7 +#define CLK_R_APB1_PPU 8 +#define CLK_R_APB2_UART 9 +#define CLK_R_APB2_I2C0 10 +#define CLK_R_APB2_I2C1 11 +#define CLK_R_APB1_IR 12 +#define CLK_R_APB1_BUS_IR 13 +#define CLK_R_AHB_BUS_RTC 14 + +#endif /* _DT_BINDINGS_CLK_SUN50I_A100_R_CCU_H_ */ diff --git a/include/dt-bindings/reset/sun50i-a100-ccu.h b/include/dt-bindings/reset/sun50i-a100-ccu.h new file mode 100644 index 000000000000..3aeea481c717 --- /dev/null +++ b/include/dt-bindings/reset/sun50i-a100-ccu.h @@ -0,0 +1,68 @@ +/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */ +/* + * Copyright (c) 2020 Frank Lee <frank@allwinner.com> + */ + +#ifndef _DT_BINDINGS_RESET_SUN50I_A100_H_ +#define _DT_BINDINGS_RESET_SUN50I_A100_H_ + +#define RST_MBUS 0 +#define RST_BUS_DE 1 +#define RST_BUS_G2D 2 +#define RST_BUS_GPU 3 +#define RST_BUS_CE 4 +#define RST_BUS_VE 5 +#define RST_BUS_DMA 6 +#define RST_BUS_MSGBOX 7 +#define RST_BUS_SPINLOCK 8 +#define RST_BUS_HSTIMER 9 +#define RST_BUS_DBG 10 +#define RST_BUS_PSI 11 +#define RST_BUS_PWM 12 +#define RST_BUS_DRAM 13 +#define RST_BUS_NAND 14 +#define RST_BUS_MMC0 15 +#define RST_BUS_MMC1 16 +#define RST_BUS_MMC2 17 +#define RST_BUS_UART0 18 +#define RST_BUS_UART1 19 +#define RST_BUS_UART2 20 +#define RST_BUS_UART3 21 +#define RST_BUS_UART4 22 +#define RST_BUS_I2C0 23 +#define RST_BUS_I2C1 24 +#define RST_BUS_I2C2 25 +#define RST_BUS_I2C3 26 +#define RST_BUS_SPI0 27 +#define RST_BUS_SPI1 28 +#define RST_BUS_SPI2 29 +#define RST_BUS_EMAC 30 +#define RST_BUS_IR_RX 31 +#define RST_BUS_IR_TX 32 +#define RST_BUS_GPADC 33 +#define RST_BUS_THS 34 +#define RST_BUS_I2S0 35 +#define RST_BUS_I2S1 36 +#define RST_BUS_I2S2 37 +#define RST_BUS_I2S3 38 +#define RST_BUS_SPDIF 39 +#define RST_BUS_DMIC 40 +#define RST_BUS_AUDIO_CODEC 41 +#define RST_USB_PHY0 42 +#define RST_USB_PHY1 43 +#define RST_BUS_OHCI0 44 +#define RST_BUS_OHCI1 45 +#define RST_BUS_EHCI0 46 +#define RST_BUS_EHCI1 47 +#define RST_BUS_OTG 48 +#define RST_BUS_LRADC 49 +#define RST_BUS_DPSS_TOP0 50 +#define RST_BUS_DPSS_TOP1 51 +#define RST_BUS_MIPI_DSI 52 +#define RST_BUS_TCON_LCD 53 +#define RST_BUS_LVDS 54 +#define RST_BUS_LEDC 55 +#define RST_BUS_CSI 56 +#define RST_BUS_CSI_ISP 57 + +#endif /* _DT_BINDINGS_RESET_SUN50I_A100_H_ */ diff --git a/include/dt-bindings/reset/sun50i-a100-r-ccu.h b/include/dt-bindings/reset/sun50i-a100-r-ccu.h new file mode 100644 index 000000000000..366ccf791c43 --- /dev/null +++ b/include/dt-bindings/reset/sun50i-a100-r-ccu.h @@ -0,0 +1,18 @@ +/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */ +/* + * Copyright (c) 2020 Frank Lee <frank@allwinner.com> + */ + +#ifndef _DT_BINDINGS_RST_SUN50I_A100_R_CCU_H_ +#define _DT_BINDINGS_RST_SUN50I_A100_R_CCU_H_ + +#define RST_R_APB1_TIMER 0 +#define RST_R_APB1_BUS_PWM 1 +#define RST_R_APB1_PPU 2 +#define RST_R_APB2_UART 3 +#define RST_R_APB2_I2C0 4 +#define RST_R_APB2_I2C1 5 +#define RST_R_APB1_BUS_IR 6 +#define RST_R_AHB_BUS_RTC 7 + +#endif /* _DT_BINDINGS_RST_SUN50I_A100_R_CCU_H_ */ -- 2.24.0 ^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: [PATCH 1/4] clk: sunxi-ng: add support for the Allwinner A100 CCU 2020-05-22 3:07 ` [PATCH 1/4] clk: sunxi-ng: add support for the Allwinner A100 CCU Frank Lee @ 2020-05-22 15:14 ` Maxime Ripard 2020-06-03 9:42 ` 回复：[PATCH " 李扬韬 0 siblings, 1 reply; 15+ messages in thread From: Maxime Ripard @ 2020-05-22 15:14 UTC (permalink / raw) To: Frank Lee Cc: wens, robh+dt, mturquette, sboyd, linus.walleij, p.zabel, huangshuosheng, tiny.windzz, linux-arm-kernel, devicetree, linux-kernel, linux-clk, linux-gpio [-- Attachment #1: Type: text/plain, Size: 60865 bytes --] Hi, On Fri, May 22, 2020 at 11:07:40AM +0800, Frank Lee wrote: > Add support for a100 in the sunxi-ng CCU framework. > > Signed-off-by: Frank Lee <frank@allwinnertech.com> > --- > drivers/clk/sunxi-ng/Kconfig | 10 + > drivers/clk/sunxi-ng/Makefile | 2 + > drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c | 206 +++ > drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h | 14 + > drivers/clk/sunxi-ng/ccu-sun50i-a100.c | 1255 +++++++++++++++++ > drivers/clk/sunxi-ng/ccu-sun50i-a100.h | 14 + > include/dt-bindings/clock/sun50i-a100-ccu.h | 141 ++ > include/dt-bindings/clock/sun50i-a100-r-ccu.h | 25 + > include/dt-bindings/reset/sun50i-a100-ccu.h | 68 + > include/dt-bindings/reset/sun50i-a100-r-ccu.h | 18 + > 10 files changed, 1753 insertions(+) > create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c > create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h > create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.c > create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.h > create mode 100644 include/dt-bindings/clock/sun50i-a100-ccu.h > create mode 100644 include/dt-bindings/clock/sun50i-a100-r-ccu.h > create mode 100644 include/dt-bindings/reset/sun50i-a100-ccu.h > create mode 100644 include/dt-bindings/reset/sun50i-a100-r-ccu.h > > diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig > index cdf333003c30..ce5f5847d5d3 100644 > --- a/drivers/clk/sunxi-ng/Kconfig > +++ b/drivers/clk/sunxi-ng/Kconfig > @@ -17,6 +17,16 @@ config SUN50I_A64_CCU > default ARM64 && ARCH_SUNXI > depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST > > +config SUN50I_A100_CCU > + bool "Support for the Allwinner A100 CCU" > + default ARM64 && ARCH_SUNXI > + depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST > + > +config SUN50I_A100_R_CCU > + bool "Support for the Allwinner A100 PRCM CCU" > + default ARM64 && ARCH_SUNXI > + depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST > + > config SUN50I_H6_CCU > bool "Support for the Allwinner H6 CCU" > default ARM64 && ARCH_SUNXI > diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile > index 4c7bee883f2f..3eb5cff40eac 100644 > --- a/drivers/clk/sunxi-ng/Makefile > +++ b/drivers/clk/sunxi-ng/Makefile > @@ -23,6 +23,8 @@ obj-y += ccu_mp.o > # SoC support > obj-$(CONFIG_SUNIV_F1C100S_CCU) += ccu-suniv-f1c100s.o > obj-$(CONFIG_SUN50I_A64_CCU) += ccu-sun50i-a64.o > +obj-$(CONFIG_SUN50I_A100_CCU) += ccu-sun50i-a100.o > +obj-$(CONFIG_SUN50I_A100_R_CCU) += ccu-sun50i-a100-r.o > obj-$(CONFIG_SUN50I_H6_CCU) += ccu-sun50i-h6.o > obj-$(CONFIG_SUN50I_H6_R_CCU) += ccu-sun50i-h6-r.o > obj-$(CONFIG_SUN4I_A10_CCU) += ccu-sun4i-a10.o > diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c > new file mode 100644 > index 000000000000..31875269ef90 > --- /dev/null > +++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c > @@ -0,0 +1,206 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (c) 2020 Frank Lee <frank@allwinner.com> The domain doesn't match the one used to send that patch, is that intentional? > + */ > + > +#include <linux/clk-provider.h> > +#include <linux/module.h> > +#include <linux/of_address.h> > +#include <linux/platform_device.h> > + > +#include "ccu_common.h" > +#include "ccu_reset.h" > + > +#include "ccu_div.h" > +#include "ccu_gate.h" > +#include "ccu_mp.h" > +#include "ccu_nm.h" > + > +#include "ccu-sun50i-a100-r.h" > + > +static const char * const cpus_r_apb2_parents[] = { "dcxo24M", "osc32k", > + "iosc", "pll-periph0" }; > +static const struct ccu_mux_var_prediv cpus_r_apb2_predivs[] = { > + { .index = 3, .shift = 0, .width = 5 }, > +}; > + > +static struct ccu_div cpus_clk = { > + .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO), > + > + .mux = { > + .shift = 24, > + .width = 2, > + > + .var_predivs = cpus_r_apb2_predivs, > + .n_var_predivs = ARRAY_SIZE(cpus_r_apb2_predivs), > + }, > + > + .common = { > + .reg = 0x000, > + .features = CCU_FEATURE_VARIABLE_PREDIV, > + .hw.init = CLK_HW_INIT_PARENTS("cpus", > + cpus_r_apb2_parents, > + &ccu_div_ops, > + 0), > + }, > +}; > + > +static CLK_FIXED_FACTOR_HW(r_ahb_clk, "r-ahb", &cpus_clk.common.hw, 1, 1, 0); > + > +static struct ccu_div r_apb1_clk = { > + .div = _SUNXI_CCU_DIV(0, 2), > + > + .common = { > + .reg = 0x00c, > + .hw.init = CLK_HW_INIT("r-apb1", > + "r-ahb", > + &ccu_div_ops, > + 0), > + }, > +}; > + > +static struct ccu_div r_apb2_clk = { > + .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO), > + > + .mux = { > + .shift = 24, > + .width = 2, > + > + .var_predivs = cpus_r_apb2_predivs, > + .n_var_predivs = ARRAY_SIZE(cpus_r_apb2_predivs), > + }, > + > + .common = { > + .reg = 0x010, > + .features = CCU_FEATURE_VARIABLE_PREDIV, > + .hw.init = CLK_HW_INIT_PARENTS("r-apb2", > + cpus_r_apb2_parents, > + &ccu_div_ops, > + 0), > + }, > +}; > + > +static SUNXI_CCU_GATE(r_apb1_timer_clk, "r-apb1-timer", "r-apb1", > + 0x11c, BIT(0), 0); > + > +static SUNXI_CCU_GATE(r_apb1_twd_clk, "r-apb1-twd", "r-apb1", > + 0x12c, BIT(0), 0); > + > +static const char * const r_apb1_pwm_clk_parents[] = { "dcxo24M", "osc32k", > + "iosc" }; > +static SUNXI_CCU_MUX(r_apb1_pwm_clk, "r-apb1-pwm", r_apb1_pwm_clk_parents, > + 0x130, 24, 2, 0); > + > +static SUNXI_CCU_GATE(r_apb1_bus_pwm_clk, "r-apb1-bus-pwm", "r-apb1", > + 0x13c, BIT(0), 0); > + > +static SUNXI_CCU_GATE(r_apb1_ppu_clk, "r-apb1-ppu", "r-apb1", > + 0x17c, BIT(0), 0); > + > +static SUNXI_CCU_GATE(r_apb2_uart_clk, "r-apb2-uart", "r-apb2", > + 0x18c, BIT(0), 0); > + > +static SUNXI_CCU_GATE(r_apb2_i2c0_clk, "r-apb2-i2c0", "r-apb2", > + 0x19c, BIT(0), 0); > + > +static SUNXI_CCU_GATE(r_apb2_i2c1_clk, "r-apb2-i2c1", "r-apb2", > + 0x19c, BIT(1), 0); You should be using SUNXI_CCU_GATE_DATA here > +static const char * const r_apb1_ir_rx_parents[] = { "osc32k", "dcxo24M" }; > +static SUNXI_CCU_MP_WITH_MUX_GATE(r_apb1_ir_rx_clk, "r-apb1-ir-rx", > + r_apb1_ir_rx_parents, 0x1c0, > + 0, 5, /* M */ > + 8, 2, /* P */ > + 24, 1, /* mux */ > + BIT(31), /* gate */ > + 0); > + > +static SUNXI_CCU_GATE(r_apb1_bus_ir_rx_clk, "r-apb1-bus-ir-rx", "r-apb1", > + 0x1cc, BIT(0), 0); > + > +static SUNXI_CCU_GATE(r_ahb_bus_rtc_clk, "r-ahb-rtc", "r-ahb", > + 0x20c, BIT(0), 0); > + > +static struct ccu_common *sun50i_a100_r_ccu_clks[] = { > + &cpus_clk.common, > + &r_apb1_clk.common, > + &r_apb2_clk.common, > + &r_apb1_timer_clk.common, > + &r_apb1_twd_clk.common, > + &r_apb1_pwm_clk.common, > + &r_apb1_bus_pwm_clk.common, > + &r_apb1_ppu_clk.common, > + &r_apb2_uart_clk.common, > + &r_apb2_i2c0_clk.common, > + &r_apb2_i2c1_clk.common, > + &r_apb1_ir_rx_clk.common, > + &r_apb1_bus_ir_rx_clk.common, > + &r_ahb_bus_rtc_clk.common, > +}; > + > +static struct clk_hw_onecell_data sun50i_a100_r_hw_clks = { > + .hws = { > + [CLK_CPUS] = &cpus_clk.common.hw, > + [CLK_R_AHB] = &r_ahb_clk.hw, Having some consistency here would be great, CLK_R_CPUS would be best I guess. > + [CLK_R_APB1] = &r_apb1_clk.common.hw, > + [CLK_R_APB2] = &r_apb2_clk.common.hw, > + [CLK_R_APB1_TIMER] = &r_apb1_timer_clk.common.hw, > + [CLK_R_APB1_TWD] = &r_apb1_twd_clk.common.hw, > + [CLK_R_APB1_PWM] = &r_apb1_pwm_clk.common.hw, > + [CLK_R_APB1_BUS_PWM] = &r_apb1_bus_pwm_clk.common.hw, > + [CLK_R_APB1_PPU] = &r_apb1_ppu_clk.common.hw, > + [CLK_R_APB2_UART] = &r_apb2_uart_clk.common.hw, > + [CLK_R_APB2_I2C0] = &r_apb2_i2c0_clk.common.hw, > + [CLK_R_APB2_I2C1] = &r_apb2_i2c1_clk.common.hw, > + [CLK_R_APB1_IR] = &r_apb1_ir_rx_clk.common.hw, > + [CLK_R_APB1_BUS_IR] = &r_apb1_bus_ir_rx_clk.common.hw, > + [CLK_R_AHB_BUS_RTC] = &r_ahb_bus_rtc_clk.common.hw, > + }, > + .num = CLK_NUMBER, > +}; > + > +static struct ccu_reset_map sun50i_a100_r_ccu_resets[] = { > + [RST_R_APB1_TIMER] = { 0x11c, BIT(16) }, > + [RST_R_APB1_BUS_PWM] = { 0x13c, BIT(16) }, > + [RST_R_APB1_PPU] = { 0x17c, BIT(16) }, > + [RST_R_APB2_UART] = { 0x18c, BIT(16) }, > + [RST_R_APB2_I2C0] = { 0x19c, BIT(16) }, > + [RST_R_APB2_I2C1] = { 0x19c, BIT(17) }, > + [RST_R_APB1_BUS_IR] = { 0x1cc, BIT(16) }, > + [RST_R_AHB_BUS_RTC] = { 0x20c, BIT(16) }, > +}; > + > +static const struct sunxi_ccu_desc sun50i_a100_r_ccu_desc = { > + .ccu_clks = sun50i_a100_r_ccu_clks, > + .num_ccu_clks = ARRAY_SIZE(sun50i_a100_r_ccu_clks), > + > + .hw_clks = &sun50i_a100_r_hw_clks, > + > + .resets = sun50i_a100_r_ccu_resets, > + .num_resets = ARRAY_SIZE(sun50i_a100_r_ccu_resets), > +}; > + > +static int sun50i_a100_r_ccu_probe(struct platform_device *pdev) > +{ > + void __iomem *reg; > + > + reg = devm_platform_ioremap_resource(pdev, 0); > + if (IS_ERR(reg)) > + return PTR_ERR(reg); > + > + return sunxi_ccu_probe(pdev->dev.of_node, reg, &sun50i_a100_r_ccu_desc); > +} > + > +static const struct of_device_id sun50i_a100_r_ccu_ids[] = { > + { .compatible = "allwinner,sun50i-a100-r-ccu" }, > + { } > +}; You're going to need a DT binding here too. > +static struct platform_driver sun50i_a100_r_ccu_driver = { > + .probe = sun50i_a100_r_ccu_probe, > + .driver = { > + .name = "sun50i-a100-r-ccu", > + .of_match_table = sun50i_a100_r_ccu_ids, > + }, > +}; > +module_platform_driver(sun50i_a100_r_ccu_driver); > diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h > new file mode 100644 > index 000000000000..c26a08b924db > --- /dev/null > +++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h > @@ -0,0 +1,14 @@ > +/* SPDX-License-Identifier: GPL-2.0 */ > +/* > + * Copyright (c) 2020 Frank Lee <frank@allwinner.com> > + */ > + > +#ifndef _CCU_SUN50IW10_R_H > +#define _CCU_SUN50IW10_R_H > + > +#include <dt-bindings/clock/sun50i-a100-r-ccu.h> > +#include <dt-bindings/reset/sun50i-a100-r-ccu.h> > + > +#define CLK_NUMBER (CLK_R_AHB_BUS_RTC + 1) > + > +#endif /* _CCU_SUN50IW10_R_H */ > diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100.c b/drivers/clk/sunxi-ng/ccu-sun50i-a100.c > new file mode 100644 > index 000000000000..f9a0a7754eed > --- /dev/null > +++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100.c > @@ -0,0 +1,1255 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (c) 2020 Frank Lee <frank@allwinner.com> > + */ > + > +#include <linux/clk-provider.h> > +#include <linux/io.h> > +#include <linux/module.h> > +#include <linux/of_address.h> > +#include <linux/platform_device.h> > + > +#include "ccu_common.h" > +#include "ccu_reset.h" > + > +#include "ccu_div.h" > +#include "ccu_gate.h" > +#include "ccu_mp.h" > +#include "ccu_mult.h" > +#include "ccu_nk.h" > +#include "ccu_nkm.h" > +#include "ccu_nkmp.h" > +#include "ccu_nm.h" > + > +#include "ccu-sun50i-a100.h" > + > +/* > + * The CPU PLL is actually NP clock, with P being /1, /2 or /4. However > + * P should only be used for output frequencies lower than 288 MHz. > + * > + * For now we can just model it as a multiplier clock, and force P to /1. > + * > + * The M factor is present in the register's description, but not in the > + * frequency formula, and it's documented as "M is only used for backdoor > + * testing", so it's not modelled and then force to 0. > + */ > +#define SUN50I_A100_PLL_CPUX_REG 0x000 > +static struct ccu_mult pll_cpux_clk = { > + .enable = BIT(27), > + .lock = BIT(28), > + .mult = _SUNXI_CCU_MULT_MIN(8, 8, 12), > + .common = { > + .reg = 0x000, > + .hw.init = CLK_HW_INIT("pll-cpux", "dcxo24M", > + &ccu_mult_ops, > + CLK_SET_RATE_UNGATE), > + }, > +}; > + > +/* Some PLLs are input * N / div1 / P. Model them as NKMP with no K */ > +#define SUN50I_A100_PLL_DDR0_REG 0x010 > +static struct ccu_nkmp pll_ddr0_clk = { > + .enable = BIT(27), > + .lock = BIT(28), > + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), > + .m = _SUNXI_CCU_DIV(1, 1), /* input divider */ > + .p = _SUNXI_CCU_DIV(0, 1), /* output divider */ > + .common = { > + .reg = 0x010, > + .hw.init = CLK_HW_INIT("pll-ddr0", "dcxo24M", > + &ccu_nkmp_ops, > + CLK_SET_RATE_UNGATE | > + CLK_IS_CRITICAL), > + }, > +}; > + > +#define SUN50I_A100_PLL_PERIPH0_REG 0x020 > +static struct ccu_nkmp pll_periph0_clk = { > + .enable = BIT(27), > + .lock = BIT(28), > + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), > + .m = _SUNXI_CCU_DIV(1, 1), /* input divider */ > + .p = _SUNXI_CCU_DIV(0, 1), /* output divider */ > + .fixed_post_div = 2, > + .common = { > + .reg = 0x020, > + .features = CCU_FEATURE_FIXED_POSTDIV, > + .hw.init = CLK_HW_INIT("pll-periph0", "dcxo24M", > + &ccu_nkmp_ops, > + CLK_SET_RATE_UNGATE), > + }, > +}; > + > +#define SUN50I_A100_PLL_PERIPH1_REG 0x028 > +static struct ccu_nkmp pll_periph1_clk = { > + .enable = BIT(27), > + .lock = BIT(28), > + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), > + .m = _SUNXI_CCU_DIV(1, 1), /* input divider */ > + .p = _SUNXI_CCU_DIV(0, 1), /* output divider */ > + .fixed_post_div = 2, > + .common = { > + .reg = 0x028, > + .features = CCU_FEATURE_FIXED_POSTDIV, > + .hw.init = CLK_HW_INIT("pll-periph1", "dcxo24M", > + &ccu_nkmp_ops, > + CLK_SET_RATE_UNGATE), > + }, > +}; > +#define SUN50I_A100_PLL_PERIPH1_PATTERN0_REG 0x128 > + > +#define SUN50I_A100_PLL_GPU_REG 0x030 > +static struct ccu_nkmp pll_gpu_clk = { > + .enable = BIT(27), > + .lock = BIT(28), > + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), > + .m = _SUNXI_CCU_DIV(1, 1), /* input divider */ > + .p = _SUNXI_CCU_DIV(0, 1), /* output divider */ > + .common = { > + .reg = 0x030, > + .hw.init = CLK_HW_INIT("pll-gpu", "dcxo24M", > + &ccu_nkmp_ops, > + CLK_SET_RATE_UNGATE), > + }, > +}; > + > +/* > + * For Video PLLs, the output divider is described as "used for testing" > + * in the user manual. So it's not modelled and forced to 0. > + */ > +#define SUN50I_A100_PLL_VIDEO0_REG 0x040 > +static struct ccu_nm pll_video0_clk = { > + .enable = BIT(27), > + .lock = BIT(28), > + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), > + .m = _SUNXI_CCU_DIV(1, 1), /* input divider */ > + .fixed_post_div = 4, > + .common = { > + .reg = 0x040, > + .features = CCU_FEATURE_FIXED_POSTDIV, > + .hw.init = CLK_HW_INIT("pll-video0", "dcxo24M", > + &ccu_nm_ops, > + CLK_SET_RATE_UNGATE), > + }, > +}; > + > +#define SUN50I_A100_PLL_VIDEO1_REG 0x048 > +static struct ccu_nm pll_video1_clk = { > + .enable = BIT(27), > + .lock = BIT(28), > + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), > + .m = _SUNXI_CCU_DIV(1, 1), /* input divider */ > + .fixed_post_div = 4, > + .common = { > + .reg = 0x048, > + .features = CCU_FEATURE_FIXED_POSTDIV, > + .hw.init = CLK_HW_INIT("pll-video1", "dcxo24M", > + &ccu_nm_ops, > + CLK_SET_RATE_UNGATE), > + }, > +}; > + > +#define SUN50I_A100_PLL_VIDEO2_REG 0x050 > +static struct ccu_nm pll_video2_clk = { > + .enable = BIT(27), > + .lock = BIT(28), > + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), > + .m = _SUNXI_CCU_DIV(1, 1), /* input divider */ > + .fixed_post_div = 4, > + .common = { > + .reg = 0x050, > + .features = CCU_FEATURE_FIXED_POSTDIV, > + .hw.init = CLK_HW_INIT("pll-video2", "dcxo24M", > + &ccu_nm_ops, > + CLK_SET_RATE_UNGATE), > + }, > +}; > + > +#define SUN50I_A100_PLL_VE_REG 0x058 > +static struct ccu_nkmp pll_ve_clk = { > + .enable = BIT(27), > + .lock = BIT(28), > + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), > + .m = _SUNXI_CCU_DIV(1, 1), /* input divider */ > + .p = _SUNXI_CCU_DIV(0, 1), /* output divider */ > + .common = { > + .reg = 0x058, > + .hw.init = CLK_HW_INIT("pll-ve", "dcxo24M", > + &ccu_nkmp_ops, > + CLK_SET_RATE_UNGATE), > + }, > +}; > + > +/* > + * The COM PLL has m0 dividers in addition to the usual N, M > + * factors. Since we only need 1 frequencies from this PLL: 45.1584 MHz, > + * ignore it for now. > + */ > +#define SUN50I_A100_PLL_COM_REG 0x060 > +static struct ccu_sdm_setting pll_com_sdm_table[] = { > + { .rate = 451584000, .pattern = 0xc0014396, .m = 2, .n = 37 }, > +}; > + > +static struct ccu_nm pll_com_clk = { > + .enable = BIT(27), > + .lock = BIT(28), > + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), > + .m = _SUNXI_CCU_DIV(0, 1), > + .sdm = _SUNXI_CCU_SDM(pll_com_sdm_table, BIT(24), > + 0x160, BIT(31)), > + .common = { > + .reg = 0x060, > + .features = CCU_FEATURE_SIGMA_DELTA_MOD, > + .hw.init = CLK_HW_INIT("pll-com", "dcxo24M", > + &ccu_nm_ops, > + CLK_SET_RATE_UNGATE), > + }, > +}; > + > +#define SUN50I_A100_PLL_VIDEO3_REG 0x068 > +static struct ccu_nm pll_video3_clk = { > + .enable = BIT(27), > + .lock = BIT(28), > + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), > + .m = _SUNXI_CCU_DIV(1, 1), /* input divider */ > + .fixed_post_div = 4, > + .common = { > + .reg = 0x068, > + .features = CCU_FEATURE_FIXED_POSTDIV, > + .hw.init = CLK_HW_INIT("pll-video3", "dcxo24M", > + &ccu_nm_ops, > + CLK_SET_RATE_UNGATE), > + }, > +}; > + > +/* > + * The Audio PLL has m0, m1 dividers in addition to the usual N, M > + * factors. Since we only need 4 frequencies from this PLL: 22.5792 MHz, > + * 24.576 MHz, 90.3168MHz and 98.304MHz ignore them for now. > + * Enforce the default for them, which is m0 = 1, m1 = 0. > + */ > +#define SUN50I_A100_PLL_AUDIO_REG 0x078 > +static struct ccu_sdm_setting pll_audio_sdm_table[] = { > + { .rate = 45158400, .pattern = 0xc001bcd3, .m = 18, .n = 33 }, > + { .rate = 49152000, .pattern = 0xc001eb85, .m = 20, .n = 40 }, > + { .rate = 180633600, .pattern = 0xc001288d, .m = 3, .n = 22 }, > + { .rate = 196608000, .pattern = 0xc001eb85, .m = 5, .n = 40 }, > +}; > + > +static struct ccu_nm pll_audio_clk = { > + .enable = BIT(27), > + .lock = BIT(28), > + .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), > + .m = _SUNXI_CCU_DIV(16, 6), > + .fixed_post_div = 2, > + .sdm = _SUNXI_CCU_SDM(pll_audio_sdm_table, BIT(24), > + 0x178, BIT(31)), > + .common = { > + .reg = 0x078, > + .features = CCU_FEATURE_FIXED_POSTDIV | > + CCU_FEATURE_SIGMA_DELTA_MOD, > + .hw.init = CLK_HW_INIT("pll-audio", "dcxo24M", > + &ccu_nm_ops, > + CLK_SET_RATE_UNGATE), > + }, > +}; > + > +static const char * const cpux_parents[] = { "dcxo24M", "osc32k", > + "iosc", "pll-cpux", > + "pll-periph0" }; > +static SUNXI_CCU_MUX(cpux_clk, "cpux", cpux_parents, > + 0x500, 24, 3, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL); > +static SUNXI_CCU_M(axi_clk, "axi", "cpux", 0x500, 0, 2, 0); > +static SUNXI_CCU_M(cpux_apb_clk, "cpux-apb", "cpux", 0x500, 8, 2, 0); > + > +static const char * const psi_ahb1_ahb2_parents[] = { "dcxo24M", "osc32k", > + "iosc", "pll-periph0", > + "pll-periph0-2x" }; > +static SUNXI_CCU_MP_WITH_MUX(psi_ahb1_ahb2_clk, "psi-ahb1-ahb2", > + psi_ahb1_ahb2_parents, > + 0x510, > + 0, 2, /* M */ > + 8, 2, /* P */ > + 24, 3, /* mux */ > + 0); > + > +static const char * const ahb3_apb1_apb2_parents[] = { "dcxo24M", "osc32k", > + "psi-ahb1-ahb2", > + "pll-periph0", > + "pll-periph0-2x" }; > +static SUNXI_CCU_MP_WITH_MUX(ahb3_clk, "ahb3", ahb3_apb1_apb2_parents, 0x51c, > + 0, 2, /* M */ > + 8, 2, /* P */ > + 24, 3, /* mux */ > + 0); > + > +static SUNXI_CCU_MP_WITH_MUX(apb1_clk, "apb1", ahb3_apb1_apb2_parents, 0x520, > + 0, 2, /* M */ > + 8, 2, /* P */ > + 24, 3, /* mux */ > + 0); > + > +static SUNXI_CCU_MP_WITH_MUX(apb2_clk, "apb2", ahb3_apb1_apb2_parents, 0x524, > + 0, 2, /* M */ > + 8, 2, /* P */ > + 24, 3, /* mux */ > + 0); > + > +static const char * const mbus_parents[] = { "dcxo24M", "pll-ddr0", > + "pll-periph0", > + "pll-periph0-2x" }; > +static SUNXI_CCU_M_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents, 0x540, > + 0, 3, /* M */ > + 24, 2, /* mux */ > + BIT(31), /* gate */ > + CLK_IS_CRITICAL); > + > +static const char * const de_parents[] = { "pll-com", "pll-periph0-2x" }; > +static SUNXI_CCU_M_WITH_MUX_GATE(de_clk, "de0", de_parents, 0x600, > + 0, 4, /* M */ > + 24, 1, /* mux */ > + BIT(31), /* gate */ > + CLK_SET_RATE_PARENT); > + > +static SUNXI_CCU_GATE(bus_de_clk, "bus-de", "psi-ahb1-ahb2", > + 0x60c, BIT(0), 0); > + > +static const char * const g2d_parents[] = { "pll-com", "pll-periph0-2x", > + "pll-video0-2x", "pll-video1-2x", > + "pll-video2-2x"}; > +static SUNXI_CCU_M_WITH_MUX_GATE(g2d_clk, "g2d", > + g2d_parents, > + 0x630, > + 0, 4, /* M */ > + 24, 3, /* mux */ > + BIT(31), /* gate */ > + 0); > + > +static SUNXI_CCU_GATE(bus_g2d_clk, "bus-g2d", "psi-ahb1-ahb2", > + 0x63c, BIT(0), 0); > + > +static const char * const gpu_parents[] = { "pll-gpu" }; > +static SUNXI_CCU_M_WITH_MUX_GATE(gpu_clk, "gpu", gpu_parents, 0x670, > + 0, 2, /* M */ > + 24, 1, /* mux */ > + BIT(31), /* gate */ > + 0); > + > +static SUNXI_CCU_GATE(bus_gpu_clk, "bus-gpu", "psi-ahb1-ahb2", > + 0x67c, BIT(0), 0); > + > +static const char * const ce_parents[] = { "dcxo24M", "pll-periph0-2x" }; > +static SUNXI_CCU_MP_WITH_MUX_GATE(ce_clk, "ce", ce_parents, 0x680, > + 0, 4, /* M */ > + 8, 2, /* N */ > + 24, 1, /* mux */ > + BIT(31), /* gate */ > + 0); > + > +static SUNXI_CCU_GATE(bus_ce_clk, "bus-ce", "psi-ahb1-ahb2", > + 0x68c, BIT(0), 0); > + > +static const char * const ve_parents[] = { "pll-ve" }; > +static SUNXI_CCU_M_WITH_MUX_GATE(ve_clk, "ve", ve_parents, 0x690, > + 0, 3, /* M */ > + 24, 1, /* mux */ > + BIT(31), /* gate */ > + CLK_SET_RATE_PARENT); > + > +static SUNXI_CCU_GATE(bus_ve_clk, "bus-ve", "psi-ahb1-ahb2", > + 0x69c, BIT(0), 0); > + > +static SUNXI_CCU_GATE(bus_dma_clk, "bus-dma", "psi-ahb1-ahb2", > + 0x70c, BIT(0), 0); > + > +static SUNXI_CCU_GATE(bus_msgbox_clk, "bus-msgbox", "psi-ahb1-ahb2", > + 0x71c, BIT(0), 0); > + > +static SUNXI_CCU_GATE(bus_spinlock_clk, "bus-spinlock", "psi-ahb1-ahb2", > + 0x72c, BIT(0), 0); > + > +static SUNXI_CCU_GATE(bus_hstimer_clk, "bus-hstimer", "psi-ahb1-ahb2", > + 0x73c, BIT(0), 0); > + > +static SUNXI_CCU_GATE(avs_clk, "avs", "dcxo24M", 0x740, BIT(31), 0); > + > +static SUNXI_CCU_GATE(bus_dbg_clk, "bus-dbg", "psi-ahb1-ahb2", > + 0x78c, BIT(0), 0); > + > +static SUNXI_CCU_GATE(bus_psi_clk, "bus-psi", "psi-ahb1-ahb2", > + 0x79c, BIT(0), 0); > + > +static SUNXI_CCU_GATE(bus_pwm_clk, "bus-pwm", "apb1", 0x7ac, BIT(0), 0); > + > +static SUNXI_CCU_GATE(bus_iommu_clk, "bus-iommu", "apb1", 0x7bc, BIT(0), 0); > + > +static SUNXI_CCU_GATE(mbus_dma_clk, "mbus-dma", "mbus", > + 0x804, BIT(0), 0); > +static SUNXI_CCU_GATE(mbus_ve_clk, "mbus-ve", "mbus", > + 0x804, BIT(1), 0); > +static SUNXI_CCU_GATE(mbus_ce_clk, "mbus-ce", "mbus", > + 0x804, BIT(2), 0); > +static SUNXI_CCU_GATE(mbus_nand_clk, "mbus-nand", "mbus", > + 0x804, BIT(5), 0); > +static SUNXI_CCU_GATE(mbus_csi_clk, "mbus-csi", "mbus", > + 0x804, BIT(8), 0); > +static SUNXI_CCU_GATE(mbus_isp_clk, "mbus-isp", "mbus", > + 0x804, BIT(9), 0); > +static SUNXI_CCU_GATE(mbus_g2d_clk, "mbus-g2d", "mbus", > + 0x804, BIT(10), 0); > + > +static SUNXI_CCU_GATE(bus_dram_clk, "bus-dram", "psi-ahb1-ahb2", > + 0x80c, BIT(0), CLK_IS_CRITICAL); > + > +static const char * const nand_spi_parents[] = { "dcxo24M", > + "pll-periph0", > + "pll-periph1", > + "pll-periph0-2x", > + "pll-periph1-2x" }; > +static SUNXI_CCU_MP_WITH_MUX_GATE(nand0_clk, "nand0", nand_spi_parents, 0x810, > + 0, 4, /* M */ > + 8, 2, /* N */ > + 24, 3, /* mux */ > + BIT(31), /* gate */ > + 0); > + > +static SUNXI_CCU_MP_WITH_MUX_GATE(nand1_clk, "nand1", nand_spi_parents, 0x814, > + 0, 4, /* M */ > + 8, 2, /* N */ > + 24, 3, /* mux */ > + BIT(31), /* gate */ > + 0); > + > +static SUNXI_CCU_GATE(bus_nand_clk, "bus-nand", "ahb3", 0x82c, BIT(0), 0); > + > +/* don't use postdiv for bsp kernel */ > +static const char * const mmc_parents[] = { "dcxo24M", "pll-periph0-2x", > + "pll-periph1-2x" }; > +static SUNXI_CCU_MP_WITH_MUX_GATE(mmc0_clk, "mmc0", mmc_parents, 0x830, > + 0, 4, /* M */ > + 8, 2, /* N */ > + 24, 2, /* mux */ > + BIT(31), /* gate */ > + CLK_SET_RATE_NO_REPARENT); > + > +static SUNXI_CCU_MP_WITH_MUX_GATE(mmc1_clk, "mmc1", mmc_parents, 0x834, > + 0, 4, /* M */ > + 8, 2, /* N */ > + 24, 2, /* mux */ > + BIT(31), /* gate */ > + CLK_SET_RATE_NO_REPARENT); > + > +static SUNXI_CCU_MP_WITH_MUX_GATE(mmc2_clk, "mmc2", mmc_parents, 0x838, > + 0, 4, /* M */ > + 8, 2, /* N */ > + 24, 2, /* mux */ > + BIT(31), /* gate */ > + CLK_SET_RATE_NO_REPARENT); > + > +static SUNXI_CCU_GATE(bus_mmc0_clk, "bus-mmc0", "ahb3", 0x84c, BIT(0), 0); > +static SUNXI_CCU_GATE(bus_mmc1_clk, "bus-mmc1", "ahb3", 0x84c, BIT(1), 0); > +static SUNXI_CCU_GATE(bus_mmc2_clk, "bus-mmc2", "ahb3", 0x84c, BIT(2), 0); > + > +static SUNXI_CCU_GATE(bus_uart0_clk, "bus-uart0", "apb2", 0x90c, BIT(0), 0); > +static SUNXI_CCU_GATE(bus_uart1_clk, "bus-uart1", "apb2", 0x90c, BIT(1), 0); > +static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2", 0x90c, BIT(2), 0); > +static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2", 0x90c, BIT(3), 0); > +static SUNXI_CCU_GATE(bus_uart4_clk, "bus-uart4", "apb2", 0x90c, BIT(4), 0); > + > +static SUNXI_CCU_GATE(bus_i2c0_clk, "bus-i2c0", "apb2", 0x91c, BIT(0), 0); > +static SUNXI_CCU_GATE(bus_i2c1_clk, "bus-i2c1", "apb2", 0x91c, BIT(1), 0); > +static SUNXI_CCU_GATE(bus_i2c2_clk, "bus-i2c2", "apb2", 0x91c, BIT(2), 0); > +static SUNXI_CCU_GATE(bus_i2c3_clk, "bus-i2c3", "apb2", 0x91c, BIT(3), 0); > + > +static SUNXI_CCU_MP_WITH_MUX_GATE(spi0_clk, "spi0", nand_spi_parents, 0x940, > + 0, 4, /* M */ > + 8, 2, /* N */ > + 24, 3, /* mux */ > + BIT(31), /* gate */ > + 0); > + > +static SUNXI_CCU_MP_WITH_MUX_GATE(spi1_clk, "spi1", nand_spi_parents, 0x944, > + 0, 4, /* M */ > + 8, 2, /* N */ > + 24, 3, /* mux */ > + BIT(31), /* gate */ > + 0); > + > +static SUNXI_CCU_MP_WITH_MUX_GATE(spi2_clk, "spi2", nand_spi_parents, 0x948, > + 0, 4, /* M */ > + 8, 2, /* N */ > + 24, 3, /* mux */ > + BIT(31), /* gate */ > + 0); > + > +static SUNXI_CCU_GATE(bus_spi0_clk, "bus-spi0", "ahb3", 0x96c, BIT(0), 0); > +static SUNXI_CCU_GATE(bus_spi1_clk, "bus-spi1", "ahb3", 0x96c, BIT(1), 0); > +static SUNXI_CCU_GATE(bus_spi2_clk, "bus-spi2", "ahb3", 0x96c, BIT(2), 0); > + > +static SUNXI_CCU_GATE(emac_25m_clk, "emac-25m", "ahb3", 0x970, > + BIT(31) | BIT(30), 0); > + > +static SUNXI_CCU_GATE(bus_emac_clk, "bus-emac", "ahb3", 0x97c, BIT(0), 0); > + > +static const char * const ir_parents[] = { "osc32k", "iosc", > + "pll-periph0", "pll-periph1" }; > +static SUNXI_CCU_MP_WITH_MUX_GATE(ir_rx_clk, "ir-rx", ir_parents, 0x990, > + 0, 4, /* M */ > + 8, 2, /* N */ > + 24, 3, /* mux */ > + BIT(31), /* gate */ > + 0); > + > +static SUNXI_CCU_GATE(bus_ir_rx_clk, "bus-ir-rx", "ahb3", 0x99c, BIT(0), 0); > + > +static SUNXI_CCU_MP_WITH_MUX_GATE(ir_tx_clk, "ir-tx", ir_parents, 0x9c0, > + 0, 4, /* M */ > + 8, 2, /* N */ > + 24, 3, /* mux */ > + BIT(31), /* gate */ > + 0); > + > +static SUNXI_CCU_GATE(bus_ir_tx_clk, "bus-ir-tx", "apb1", 0x9cc, BIT(0), 0); > + > +static SUNXI_CCU_GATE(bus_gpadc_clk, "bus-gpadc", "apb1", 0x9ec, BIT(0), 0); > + > +static SUNXI_CCU_GATE(bus_ths_clk, "bus-ths", "apb1", 0x9fc, BIT(0), 0); > + > +static const char * const audio_parents[] = { "pll-audio", "pll-com-audio" }; > +static struct ccu_div i2s0_clk = { > + .enable = BIT(31), > + .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO), > + .mux = _SUNXI_CCU_MUX(24, 2), > + .common = { > + .reg = 0xa10, > + .hw.init = CLK_HW_INIT_PARENTS("i2s0", > + audio_parents, > + &ccu_div_ops, > + CLK_SET_RATE_PARENT), > + }, > +}; > + > +static struct ccu_div i2s1_clk = { > + .enable = BIT(31), > + .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO), > + .mux = _SUNXI_CCU_MUX(24, 2), > + .common = { > + .reg = 0xa14, > + .hw.init = CLK_HW_INIT_PARENTS("i2s1", > + audio_parents, > + &ccu_div_ops, > + CLK_SET_RATE_PARENT), > + }, > +}; > + > +static struct ccu_div i2s2_clk = { > + .enable = BIT(31), > + .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO), > + .mux = _SUNXI_CCU_MUX(24, 2), > + .common = { > + .reg = 0xa18, > + .hw.init = CLK_HW_INIT_PARENTS("i2s2", > + audio_parents, > + &ccu_div_ops, > + CLK_SET_RATE_PARENT), > + }, > +}; > + > +static struct ccu_div i2s3_clk = { > + .enable = BIT(31), > + .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO), > + .mux = _SUNXI_CCU_MUX(24, 2), > + .common = { > + .reg = 0xa1c, > + .hw.init = CLK_HW_INIT_PARENTS("i2s3", > + audio_parents, > + &ccu_div_ops, > + CLK_SET_RATE_PARENT), > + }, > +}; > + > +static SUNXI_CCU_GATE(bus_i2s0_clk, "bus-i2s0", "apb1", 0xa20, BIT(0), 0); > +static SUNXI_CCU_GATE(bus_i2s1_clk, "bus-i2s1", "apb1", 0xa20, BIT(1), 0); > +static SUNXI_CCU_GATE(bus_i2s2_clk, "bus-i2s2", "apb1", 0xa20, BIT(2), 0); > +static SUNXI_CCU_GATE(bus_i2s3_clk, "bus-i2s3", "apb1", 0xa20, BIT(3), 0); > + > +static struct ccu_div spdif_clk = { > + .enable = BIT(31), > + .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO), > + .mux = _SUNXI_CCU_MUX(24, 2), > + .common = { > + .reg = 0xa24, > + .hw.init = CLK_HW_INIT_PARENTS("spdif", > + audio_parents, > + &ccu_div_ops, > + 0), > + }, > +}; > + > +static SUNXI_CCU_GATE(bus_spdif_clk, "bus-spdif", "apb1", 0xa2c, BIT(0), 0); > + > +static struct ccu_div dmic_clk = { > + .enable = BIT(31), > + .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO), > + .mux = _SUNXI_CCU_MUX(24, 2), > + .common = { > + .reg = 0xa40, > + .hw.init = CLK_HW_INIT_PARENTS("dmic", > + audio_parents, > + &ccu_div_ops, > + 0), > + }, > +}; > + > +static SUNXI_CCU_GATE(bus_dmic_clk, "bus-dmic", "apb1", 0xa4c, BIT(0), 0); > + > +static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_dac_clk, "audio-codec-dac", > + audio_parents, 0xa50, > + 0, 4, /* M */ > + 24, 2, /* mux */ > + BIT(31), /* gate */ > + 0); > + > +static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_adc_clk, "audio-codec-adc", > + audio_parents, 0xa54, > + 0, 4, /* M */ > + 24, 2, /* mux */ > + BIT(31), /* gate */ > + 0); > + > +static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_4x_clk, "audio-codec-4x", > + audio_parents, 0xa58, > + 0, 4, /* M */ > + 24, 2, /* mux */ > + BIT(31), /* gate */ > + 0); > + > +static SUNXI_CCU_GATE(bus_audio_codec_clk, "bus-audio-codec", "apb1", 0xa5c, > + BIT(0), 0); > + > +/* > + * There are OHCI 12M clock source selection bits for 2 USB 2.0 ports. > + * We will force them to 0 (12M divided from 48M). > + */ > +#define SUN50I_A100_USB0_CLK_REG 0xa70 > +#define SUN50I_A100_USB1_CLK_REG 0xa74 > + > +static SUNXI_CCU_GATE(usb_ohci0_clk, "usb-ohci0", "osc12M", 0xa70, BIT(31), 0); > +static SUNXI_CCU_GATE(usb_phy0_clk, "usb-phy0", "dcxo24M", 0xa70, BIT(29), 0); > + > +static SUNXI_CCU_GATE(usb_ohci1_clk, "usb-ohci1", "osc12M", 0xa74, BIT(31), 0); > +static SUNXI_CCU_GATE(usb_phy1_clk, "usb-phy1", "dcxo24M", 0xa74, BIT(29), 0); > + > +static SUNXI_CCU_GATE(bus_ohci0_clk, "bus-ohci0", "ahb3", 0xa8c, BIT(0), 0); > +static SUNXI_CCU_GATE(bus_ohci1_clk, "bus-ohci1", "ahb3", 0xa8c, BIT(1), 0); > +static SUNXI_CCU_GATE(bus_ehci0_clk, "bus-ehci0", "ahb3", 0xa8c, BIT(4), 0); > +static SUNXI_CCU_GATE(bus_ehci1_clk, "bus-ehci1", "ahb3", 0xa8c, BIT(5), 0); > +static SUNXI_CCU_GATE(bus_otg_clk, "bus-otg", "ahb3", 0xa8c, BIT(8), 0); > + > +static SUNXI_CCU_GATE(bus_lradc_clk, "bus-lradc", "ahb3", 0xa9c, BIT(0), 0); > + > +static SUNXI_CCU_GATE(bus_dpss_top0_clk, "bus-dpss-top0", "ahb3", > + 0xabc, BIT(0), 0); > + > +static SUNXI_CCU_GATE(bus_dpss_top1_clk, "bus-dpss-top1", "ahb3", > + 0xacc, BIT(0), 0); > + > +static const char * const mipi_dsi_parents[] = { "dcxo24M", "pll-periph0-2x", > + "pll-periph0" }; > +static SUNXI_CCU_M_WITH_MUX_GATE(mipi_dsi_clk, "mipi-dsi", > + mipi_dsi_parents, > + 0xb24, > + 0, 4, /* M */ > + 24, 2, /* mux */ > + BIT(31), /* gate */ > + 0); > + > +static SUNXI_CCU_GATE(bus_mipi_dsi_clk, "bus-mipi-dsi", "ahb3", > + 0xb4c, BIT(0), 0); > + > +static const char * const tcon_lcd_parents[] = { "pll-video0-4x", > + "pll-video1-4x", > + "pll-video2-4x", > + "pll-video3-4x", > + "pll-periph0-2x" }; > +static SUNXI_CCU_MP_WITH_MUX_GATE(tcon_lcd_clk, "tcon-lcd0", > + tcon_lcd_parents, 0xb60, > + 0, 4, /* M */ > + 8, 2, /* N */ > + 24, 3, /* mux */ > + BIT(31), /* gate */ > + 0); > + > +static SUNXI_CCU_GATE(bus_tcon_lcd_clk, "bus-tcon-lcd0", "ahb3", > + 0xb7c, BIT(0), 0); > + > +static const char * const ledc_parents[] = { "dcxo24M", > + "pll-periph0" }; > +static SUNXI_CCU_MP_WITH_MUX_GATE(ledc_clk, "ledc", > + ledc_parents, 0xbf0, > + 0, 4, /* M */ > + 8, 2, /* N */ > + 24, 3, /* mux */ > + BIT(31), /* gate */ > + 0); > + > +static SUNXI_CCU_GATE(bus_ledc_clk, "bus-ledc", "ahb3", 0xbfc, BIT(0), 0); > + > +static const char * const csi_top_parents[] = { "pll-periph0-2x", > + "pll-video0-2x", > + "pll-video1-2x", > + "pll-video2-2x", > + "pll-video3-2x" }; > +static SUNXI_CCU_M_WITH_MUX_GATE(csi_top_clk, "csi-top", > + csi_top_parents, 0xc04, > + 0, 4, /* M */ > + 24, 3, /* mux */ > + BIT(31), /* gate */ > + 0); > + > +static const char * const csi0_mclk_parents[] = { "dcxo24M", "pll-video2", > + "pll-video3", "pll-video0", > + "pll-video1" }; > +static SUNXI_CCU_M_WITH_MUX_GATE(csi0_mclk_clk, "csi0-mclk", > + csi0_mclk_parents, 0xc08, > + 0, 5, /* M */ > + 24, 3, /* mux */ > + BIT(31), /* gate */ > + 0); > + > +static const char * const csi1_mclk_parents[] = { "dcxo24M", "pll-video3", > + "pll-video0", "pll-video1", > + "pll-video2" }; > +static SUNXI_CCU_M_WITH_MUX_GATE(csi1_mclk_clk, "csi1-mclk", > + csi1_mclk_parents, 0xc0c, > + 0, 5, /* M */ > + 24, 3, /* mux */ > + BIT(31), /* gate */ > + 0); > + > +static SUNXI_CCU_GATE(bus_csi_clk, "bus-csi", "ahb3", 0xc1c, BIT(0), 0); > + > +static const char * const csi_isp_parents[] = { "pll-periph0-2x", > + "pll-video0-2x", > + "pll-video1-2x", > + "pll-video2-2x", > + "pll-video3-2x" }; > +static SUNXI_CCU_M_WITH_MUX_GATE(csi_isp_clk, "csi-isp", > + csi_isp_parents, 0xc20, > + 0, 5, /* M */ > + 24, 3, /* mux */ > + BIT(31), /* gate */ > + 0); > + > +/* Fixed factor clocks */ > +static CLK_FIXED_FACTOR_FW_NAME(osc12M_clk, "osc12M", "hosc", 2, 1, 0); > + > +static CLK_FIXED_FACTOR_HW(pll_com_audio_clk, "pll-com-audio", > + &pll_com_clk.common.hw, > + 5, 1, CLK_SET_RATE_PARENT); > + > +static CLK_FIXED_FACTOR_HW(pll_periph0_2x_clk, "pll-periph0-2x", > + &pll_periph0_clk.common.hw, > + 1, 2, 0); > + > +static CLK_FIXED_FACTOR_HW(pll_periph1_2x_clk, "pll-periph1-2x", > + &pll_periph1_clk.common.hw, > + 1, 2, 0); > + > +static const struct clk_hw *pll_video0_parents[] = { > + &pll_video0_clk.common.hw > +}; > +static CLK_FIXED_FACTOR_HWS(pll_video0_4x_clk, "pll-video0-4x", > + pll_video0_parents, > + 1, 4, CLK_SET_RATE_PARENT); > +static CLK_FIXED_FACTOR_HWS(pll_video0_2x_clk, "pll-video0-2x", > + pll_video0_parents, > + 1, 2, CLK_SET_RATE_PARENT); > + > +static const struct clk_hw *pll_video1_parents[] = { > + &pll_video1_clk.common.hw > +}; > +static CLK_FIXED_FACTOR_HWS(pll_video1_4x_clk, "pll-video1-4x", > + pll_video1_parents, > + 1, 4, CLK_SET_RATE_PARENT); > +static CLK_FIXED_FACTOR_HWS(pll_video1_2x_clk, "pll-video1-2x", > + pll_video1_parents, > + 1, 2, CLK_SET_RATE_PARENT); > + > +static const struct clk_hw *pll_video2_parents[] = { > + &pll_video2_clk.common.hw > +}; > +static CLK_FIXED_FACTOR_HWS(pll_video2_4x_clk, "pll-video2-4x", > + pll_video2_parents, > + 1, 4, CLK_SET_RATE_PARENT); > +static CLK_FIXED_FACTOR_HWS(pll_video2_2x_clk, "pll-video2-2x", > + pll_video2_parents, > + 1, 2, CLK_SET_RATE_PARENT); > + > +static const struct clk_hw *pll_video3_parents[] = { > + &pll_video3_clk.common.hw > +}; > +static CLK_FIXED_FACTOR_HWS(pll_video3_4x_clk, "pll-video3-4x", > + pll_video3_parents, > + 1, 4, CLK_SET_RATE_PARENT); > +static CLK_FIXED_FACTOR_HWS(pll_video3_2x_clk, "pll-video3-2x", > + pll_video3_parents, > + 1, 2, CLK_SET_RATE_PARENT); > + > +static struct ccu_common *sun50i_a100_ccu_clks[] = { > + &pll_cpux_clk.common, > + &pll_ddr0_clk.common, > + &pll_periph0_clk.common, > + &pll_periph1_clk.common, > + &pll_gpu_clk.common, > + &pll_video0_clk.common, > + &pll_video1_clk.common, > + &pll_video2_clk.common, > + &pll_video3_clk.common, > + &pll_ve_clk.common, > + &pll_com_clk.common, > + &pll_audio_clk.common, > + &cpux_clk.common, > + &axi_clk.common, > + &cpux_apb_clk.common, > + &psi_ahb1_ahb2_clk.common, > + &ahb3_clk.common, > + &apb1_clk.common, > + &apb2_clk.common, > + &mbus_clk.common, > + &de_clk.common, > + &bus_de_clk.common, > + &g2d_clk.common, > + &bus_g2d_clk.common, > + &gpu_clk.common, > + &bus_gpu_clk.common, > + &ce_clk.common, > + &bus_ce_clk.common, > + &ve_clk.common, > + &bus_ve_clk.common, > + &bus_dma_clk.common, > + &bus_msgbox_clk.common, > + &bus_spinlock_clk.common, > + &bus_hstimer_clk.common, > + &avs_clk.common, > + &bus_dbg_clk.common, > + &bus_psi_clk.common, > + &bus_pwm_clk.common, > + &bus_iommu_clk.common, > + &mbus_dma_clk.common, > + &mbus_ve_clk.common, > + &mbus_ce_clk.common, > + &mbus_nand_clk.common, > + &mbus_csi_clk.common, > + &mbus_isp_clk.common, > + &mbus_g2d_clk.common, > + &bus_dram_clk.common, > + &nand0_clk.common, > + &nand1_clk.common, > + &bus_nand_clk.common, > + &mmc0_clk.common, > + &mmc1_clk.common, > + &mmc2_clk.common, > + &bus_mmc0_clk.common, > + &bus_mmc1_clk.common, > + &bus_mmc2_clk.common, > + &bus_uart0_clk.common, > + &bus_uart1_clk.common, > + &bus_uart2_clk.common, > + &bus_uart3_clk.common, > + &bus_uart4_clk.common, > + &bus_i2c0_clk.common, > + &bus_i2c1_clk.common, > + &bus_i2c2_clk.common, > + &bus_i2c3_clk.common, > + &spi0_clk.common, > + &spi1_clk.common, > + &spi2_clk.common, > + &bus_spi0_clk.common, > + &bus_spi1_clk.common, > + &bus_spi2_clk.common, > + &emac_25m_clk.common, > + &bus_emac_clk.common, > + &ir_rx_clk.common, > + &bus_ir_rx_clk.common, > + &ir_tx_clk.common, > + &bus_ir_tx_clk.common, > + &bus_gpadc_clk.common, > + &bus_ths_clk.common, > + &i2s0_clk.common, > + &i2s1_clk.common, > + &i2s2_clk.common, > + &i2s3_clk.common, > + &bus_i2s0_clk.common, > + &bus_i2s1_clk.common, > + &bus_i2s2_clk.common, > + &bus_i2s3_clk.common, > + &spdif_clk.common, > + &bus_spdif_clk.common, > + &dmic_clk.common, > + &bus_dmic_clk.common, > + &audio_codec_dac_clk.common, > + &audio_codec_adc_clk.common, > + &audio_codec_4x_clk.common, > + &bus_audio_codec_clk.common, > + &usb_ohci0_clk.common, > + &usb_phy0_clk.common, > + &usb_ohci1_clk.common, > + &usb_phy1_clk.common, > + &bus_ohci0_clk.common, > + &bus_ohci1_clk.common, > + &bus_ehci0_clk.common, > + &bus_ehci1_clk.common, > + &bus_otg_clk.common, > + &bus_lradc_clk.common, > + &bus_dpss_top0_clk.common, > + &bus_dpss_top1_clk.common, > + &mipi_dsi_clk.common, > + &bus_mipi_dsi_clk.common, > + &tcon_lcd_clk.common, > + &bus_tcon_lcd_clk.common, > + &ledc_clk.common, > + &bus_ledc_clk.common, > + &csi_top_clk.common, > + &csi0_mclk_clk.common, > + &csi1_mclk_clk.common, > + &bus_csi_clk.common, > + &csi_isp_clk.common, > +}; > + > +static struct clk_hw_onecell_data sun50i_a100_hw_clks = { > + .hws = { > + [CLK_OSC12M] = &osc12M_clk.hw, > + [CLK_PLL_CPUX] = &pll_cpux_clk.common.hw, > + [CLK_PLL_DDR0] = &pll_ddr0_clk.common.hw, > + [CLK_PLL_PERIPH0] = &pll_periph0_clk.common.hw, > + [CLK_PLL_PERIPH0_2X] = &pll_periph0_2x_clk.hw, > + [CLK_PLL_PERIPH1] = &pll_periph1_clk.common.hw, > + [CLK_PLL_PERIPH1_2X] = &pll_periph1_2x_clk.hw, > + [CLK_PLL_GPU] = &pll_gpu_clk.common.hw, > + [CLK_PLL_VIDEO0] = &pll_video0_clk.common.hw, > + [CLK_PLL_VIDEO0_2X] = &pll_video0_2x_clk.hw, > + [CLK_PLL_VIDEO0_4X] = &pll_video0_4x_clk.hw, > + [CLK_PLL_VIDEO1] = &pll_video1_clk.common.hw, > + [CLK_PLL_VIDEO1_2X] = &pll_video1_2x_clk.hw, > + [CLK_PLL_VIDEO1_4X] = &pll_video1_4x_clk.hw, > + [CLK_PLL_VIDEO2] = &pll_video2_clk.common.hw, > + [CLK_PLL_VIDEO2_2X] = &pll_video2_2x_clk.hw, > + [CLK_PLL_VIDEO2_4X] = &pll_video2_4x_clk.hw, > + [CLK_PLL_VIDEO3] = &pll_video3_clk.common.hw, > + [CLK_PLL_VIDEO3_2X] = &pll_video3_2x_clk.hw, > + [CLK_PLL_VIDEO3_4X] = &pll_video3_4x_clk.hw, > + [CLK_PLL_VE] = &pll_ve_clk.common.hw, > + [CLK_PLL_COM] = &pll_com_clk.common.hw, > + [CLK_PLL_COM_AUDIO] = &pll_com_audio_clk.hw, > + [CLK_PLL_AUDIO] = &pll_audio_clk.common.hw, > + [CLK_CPUX] = &cpux_clk.common.hw, > + [CLK_AXI] = &axi_clk.common.hw, > + [CLK_CPUX_APB] = &cpux_apb_clk.common.hw, > + [CLK_PSI_AHB1_AHB2] = &psi_ahb1_ahb2_clk.common.hw, > + [CLK_AHB3] = &ahb3_clk.common.hw, > + [CLK_APB1] = &apb1_clk.common.hw, > + [CLK_APB2] = &apb2_clk.common.hw, > + [CLK_MBUS] = &mbus_clk.common.hw, > + [CLK_DE] = &de_clk.common.hw, > + [CLK_BUS_DE] = &bus_de_clk.common.hw, > + [CLK_G2D] = &g2d_clk.common.hw, > + [CLK_BUS_G2D] = &bus_g2d_clk.common.hw, > + [CLK_GPU] = &gpu_clk.common.hw, > + [CLK_BUS_GPU] = &bus_gpu_clk.common.hw, > + [CLK_CE] = &ce_clk.common.hw, > + [CLK_BUS_CE] = &bus_ce_clk.common.hw, > + [CLK_VE] = &ve_clk.common.hw, > + [CLK_BUS_VE] = &bus_ve_clk.common.hw, > + [CLK_BUS_DMA] = &bus_dma_clk.common.hw, > + [CLK_BUS_MSGBOX] = &bus_msgbox_clk.common.hw, > + [CLK_BUS_SPINLOCK] = &bus_spinlock_clk.common.hw, > + [CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw, > + [CLK_AVS] = &avs_clk.common.hw, > + [CLK_BUS_DBG] = &bus_dbg_clk.common.hw, > + [CLK_BUS_PSI] = &bus_psi_clk.common.hw, > + [CLK_BUS_PWM] = &bus_pwm_clk.common.hw, > + [CLK_BUS_IOMMU] = &bus_iommu_clk.common.hw, > + [CLK_MBUS_DMA] = &mbus_dma_clk.common.hw, > + [CLK_MBUS_VE] = &mbus_ve_clk.common.hw, > + [CLK_MBUS_CE] = &mbus_ce_clk.common.hw, > + [CLK_MBUS_NAND] = &mbus_nand_clk.common.hw, > + [CLK_MBUS_CSI] = &mbus_csi_clk.common.hw, > + [CLK_MBUS_ISP] = &mbus_isp_clk.common.hw, > + [CLK_MBUS_G2D] = &mbus_g2d_clk.common.hw, > + [CLK_BUS_DRAM] = &bus_dram_clk.common.hw, > + [CLK_NAND0] = &nand0_clk.common.hw, > + [CLK_NAND1] = &nand1_clk.common.hw, > + [CLK_BUS_NAND] = &bus_nand_clk.common.hw, > + [CLK_MMC0] = &mmc0_clk.common.hw, > + [CLK_MMC1] = &mmc1_clk.common.hw, > + [CLK_MMC2] = &mmc2_clk.common.hw, > + [CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw, > + [CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw, > + [CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw, > + [CLK_BUS_UART0] = &bus_uart0_clk.common.hw, > + [CLK_BUS_UART1] = &bus_uart1_clk.common.hw, > + [CLK_BUS_UART2] = &bus_uart2_clk.common.hw, > + [CLK_BUS_UART3] = &bus_uart3_clk.common.hw, > + [CLK_BUS_UART4] = &bus_uart4_clk.common.hw, > + [CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw, > + [CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw, > + [CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw, > + [CLK_BUS_I2C3] = &bus_i2c3_clk.common.hw, > + [CLK_SPI0] = &spi0_clk.common.hw, > + [CLK_SPI1] = &spi1_clk.common.hw, > + [CLK_SPI2] = &spi2_clk.common.hw, > + [CLK_BUS_SPI0] = &bus_spi0_clk.common.hw, > + [CLK_BUS_SPI1] = &bus_spi1_clk.common.hw, > + [CLK_BUS_SPI2] = &bus_spi2_clk.common.hw, > + [CLK_EMAC_25M] = &emac_25m_clk.common.hw, > + [CLK_BUS_EMAC] = &bus_emac_clk.common.hw, > + [CLK_IR_RX] = &ir_rx_clk.common.hw, > + [CLK_BUS_IR_RX] = &bus_ir_rx_clk.common.hw, > + [CLK_IR_TX] = &ir_tx_clk.common.hw, > + [CLK_BUS_IR_TX] = &bus_ir_tx_clk.common.hw, > + [CLK_BUS_GPADC] = &bus_gpadc_clk.common.hw, > + [CLK_BUS_THS] = &bus_ths_clk.common.hw, > + [CLK_I2S0] = &i2s0_clk.common.hw, > + [CLK_I2S1] = &i2s1_clk.common.hw, > + [CLK_I2S2] = &i2s2_clk.common.hw, > + [CLK_I2S3] = &i2s3_clk.common.hw, > + [CLK_BUS_I2S0] = &bus_i2s0_clk.common.hw, > + [CLK_BUS_I2S1] = &bus_i2s1_clk.common.hw, > + [CLK_BUS_I2S2] = &bus_i2s2_clk.common.hw, > + [CLK_BUS_I2S3] = &bus_i2s3_clk.common.hw, > + [CLK_SPDIF] = &spdif_clk.common.hw, > + [CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw, > + [CLK_DMIC] = &dmic_clk.common.hw, > + [CLK_BUS_DMIC] = &bus_dmic_clk.common.hw, > + [CLK_AUDIO_DAC] = &audio_codec_dac_clk.common.hw, > + [CLK_AUDIO_ADC] = &audio_codec_adc_clk.common.hw, > + [CLK_AUDIO_4X] = &audio_codec_4x_clk.common.hw, > + [CLK_BUS_AUDIO_CODEC] = &bus_audio_codec_clk.common.hw, > + [CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw, > + [CLK_USB_PHY0] = &usb_phy0_clk.common.hw, > + [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw, > + [CLK_USB_PHY1] = &usb_phy1_clk.common.hw, > + [CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw, > + [CLK_BUS_OHCI1] = &bus_ohci1_clk.common.hw, > + [CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw, > + [CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw, > + [CLK_BUS_OTG] = &bus_otg_clk.common.hw, > + [CLK_BUS_LRADC] = &bus_lradc_clk.common.hw, > + [CLK_BUS_DPSS_TOP0] = &bus_dpss_top0_clk.common.hw, > + [CLK_BUS_DPSS_TOP1] = &bus_dpss_top1_clk.common.hw, > + [CLK_MIPI_DSI] = &mipi_dsi_clk.common.hw, > + [CLK_BUS_MIPI_DSI] = &bus_mipi_dsi_clk.common.hw, > + [CLK_TCON_LCD] = &tcon_lcd_clk.common.hw, > + [CLK_BUS_TCON_LCD] = &bus_tcon_lcd_clk.common.hw, > + [CLK_LEDC] = &ledc_clk.common.hw, > + [CLK_BUS_LEDC] = &bus_ledc_clk.common.hw, > + [CLK_CSI_TOP] = &csi_top_clk.common.hw, > + [CLK_CSI0_MCLK] = &csi0_mclk_clk.common.hw, > + [CLK_CSI1_MCLK] = &csi1_mclk_clk.common.hw, > + [CLK_BUS_CSI] = &bus_csi_clk.common.hw, > + [CLK_CSI_ISP] = &csi_isp_clk.common.hw, > + }, > + .num = CLK_NUMBER, > +}; > + > +static struct ccu_reset_map sun50i_a100_ccu_resets[] = { > + [RST_MBUS] = { 0x540, BIT(30) }, > + > + [RST_BUS_DE] = { 0x60c, BIT(16) }, > + [RST_BUS_G2D] = { 0x63c, BIT(16) }, > + [RST_BUS_GPU] = { 0x67c, BIT(16) }, > + [RST_BUS_CE] = { 0x68c, BIT(16) }, > + [RST_BUS_VE] = { 0x69c, BIT(16) }, > + [RST_BUS_DMA] = { 0x70c, BIT(16) }, > + [RST_BUS_MSGBOX] = { 0x71c, BIT(16) }, > + [RST_BUS_SPINLOCK] = { 0x72c, BIT(16) }, > + [RST_BUS_HSTIMER] = { 0x73c, BIT(16) }, > + [RST_BUS_DBG] = { 0x78c, BIT(16) }, > + [RST_BUS_PSI] = { 0x79c, BIT(16) }, > + [RST_BUS_PWM] = { 0x7ac, BIT(16) }, > + [RST_BUS_DRAM] = { 0x80c, BIT(16) }, > + [RST_BUS_NAND] = { 0x82c, BIT(16) }, > + [RST_BUS_MMC0] = { 0x84c, BIT(16) }, > + [RST_BUS_MMC1] = { 0x84c, BIT(17) }, > + [RST_BUS_MMC2] = { 0x84c, BIT(18) }, > + [RST_BUS_UART0] = { 0x90c, BIT(16) }, > + [RST_BUS_UART1] = { 0x90c, BIT(17) }, > + [RST_BUS_UART2] = { 0x90c, BIT(18) }, > + [RST_BUS_UART3] = { 0x90c, BIT(19) }, > + [RST_BUS_UART4] = { 0x90c, BIT(20) }, > + [RST_BUS_I2C0] = { 0x91c, BIT(16) }, > + [RST_BUS_I2C1] = { 0x91c, BIT(17) }, > + [RST_BUS_I2C2] = { 0x91c, BIT(18) }, > + [RST_BUS_I2C3] = { 0x91c, BIT(19) }, > + [RST_BUS_SPI0] = { 0x96c, BIT(16) }, > + [RST_BUS_SPI1] = { 0x96c, BIT(17) }, > + [RST_BUS_SPI2] = { 0x96c, BIT(18) }, > + [RST_BUS_EMAC] = { 0x97c, BIT(16) }, > + [RST_BUS_IR_RX] = { 0x99c, BIT(16) }, > + [RST_BUS_IR_TX] = { 0x9cc, BIT(16) }, > + [RST_BUS_GPADC] = { 0x9ec, BIT(16) }, > + [RST_BUS_THS] = { 0x9fc, BIT(16) }, > + [RST_BUS_I2S0] = { 0xa20, BIT(16) }, > + [RST_BUS_I2S1] = { 0xa20, BIT(17) }, > + [RST_BUS_I2S2] = { 0xa20, BIT(18) }, > + [RST_BUS_I2S3] = { 0xa20, BIT(19) }, > + [RST_BUS_SPDIF] = { 0xa2c, BIT(16) }, > + [RST_BUS_DMIC] = { 0xa4c, BIT(16) }, > + [RST_BUS_AUDIO_CODEC] = { 0xa5c, BIT(16) }, > + > + [RST_USB_PHY0] = { 0xa70, BIT(30) }, > + [RST_USB_PHY1] = { 0xa74, BIT(30) }, > + > + [RST_BUS_OHCI0] = { 0xa8c, BIT(16) }, > + [RST_BUS_OHCI1] = { 0xa8c, BIT(17) }, > + [RST_BUS_EHCI0] = { 0xa8c, BIT(20) }, > + [RST_BUS_EHCI1] = { 0xa8c, BIT(21) }, > + [RST_BUS_OTG] = { 0xa8c, BIT(24) }, > + > + [RST_BUS_LRADC] = { 0xa9c, BIT(16) }, > + [RST_BUS_DPSS_TOP0] = { 0xabc, BIT(16) }, > + [RST_BUS_DPSS_TOP1] = { 0xacc, BIT(16) }, > + [RST_BUS_MIPI_DSI] = { 0xb4c, BIT(16) }, > + [RST_BUS_TCON_LCD] = { 0xb7c, BIT(16) }, > + [RST_BUS_LVDS] = { 0xbac, BIT(16) }, > + [RST_BUS_LEDC] = { 0xbfc, BIT(16) }, > + [RST_BUS_CSI] = { 0xc1c, BIT(16) }, > + [RST_BUS_CSI_ISP] = { 0xc2c, BIT(16) }, > +}; > + > +static const struct sunxi_ccu_desc sun50i_a100_ccu_desc = { > + .ccu_clks = sun50i_a100_ccu_clks, > + .num_ccu_clks = ARRAY_SIZE(sun50i_a100_ccu_clks), > + > + .hw_clks = &sun50i_a100_hw_clks, > + > + .resets = sun50i_a100_ccu_resets, > + .num_resets = ARRAY_SIZE(sun50i_a100_ccu_resets), > +}; > + > +static const u32 pll_regs[] = { > + SUN50I_A100_PLL_CPUX_REG, > + SUN50I_A100_PLL_DDR0_REG, > + SUN50I_A100_PLL_PERIPH0_REG, > + SUN50I_A100_PLL_PERIPH1_REG, > + SUN50I_A100_PLL_GPU_REG, > + SUN50I_A100_PLL_VIDEO0_REG, > + SUN50I_A100_PLL_VIDEO1_REG, > + SUN50I_A100_PLL_VIDEO2_REG, > + SUN50I_A100_PLL_VIDEO3_REG, > + SUN50I_A100_PLL_VE_REG, > + SUN50I_A100_PLL_COM_REG, > + SUN50I_A100_PLL_AUDIO_REG, > +}; > + > +static const u32 pll_video_regs[] = { > + SUN50I_A100_PLL_VIDEO0_REG, > + SUN50I_A100_PLL_VIDEO1_REG, > + SUN50I_A100_PLL_VIDEO2_REG, > + SUN50I_A100_PLL_VIDEO3_REG, > +}; > + > +static const u32 usb2_clk_regs[] = { > + SUN50I_A100_USB0_CLK_REG, > + SUN50I_A100_USB1_CLK_REG, > +}; Using the same prefix that we use everywhere else would be nice too. > +static struct ccu_pll_nb sun50i_a100_pll_cpu_nb = { > + .common = &pll_cpux_clk.common, > + /* copy from pll_cpux_clk */ > + .enable = BIT(27), > + .lock = BIT(28), > +}; > + > +static struct ccu_mux_nb sun50i_a100_cpu_nb = { > + .common = &cpux_clk.common, > + .cm = &cpux_clk.mux, > + .delay_us = 1, > + .bypass_index = 4, /* index of pll periph0 */ > +}; > + > +static int sun50i_a100_ccu_probe(struct platform_device *pdev) > +{ > + void __iomem *reg; > + u32 val; > + int i, ret; > + > + reg = devm_platform_ioremap_resource(pdev, 0); > + if (IS_ERR(reg)) > + return PTR_ERR(reg); > + > + /* Enable the lock bits on all PLLs */ > + for (i = 0; i < ARRAY_SIZE(pll_regs); i++) { > + val = readl(reg + pll_regs[i]); > + val |= BIT(29); Having a define for that would be nice here > + writel(val, reg + pll_regs[i]); > + } > + > + /* > + * In order to pass the EMI certification, the SDM function of > + * the peripheral 1 bus is enabled, and the frequency is still > + * calculated using the previous division factor. > + */ > + writel(0xd1303333, reg + SUN50I_A100_PLL_PERIPH1_PATTERN0_REG); Same here > + val = readl(reg + SUN50I_A100_PLL_PERIPH1_REG); > + val |= BIT(24); > + writel(val, reg + SUN50I_A100_PLL_PERIPH1_REG); Same here > + /* > + * Force the output divider of video PLLs to 0. > + * > + * See the comment before pll-video0 definition for the reason. > + */ > + for (i = 0; i < ARRAY_SIZE(pll_video_regs); i++) { > + val = readl(reg + pll_video_regs[i]); > + val &= ~BIT(0); > + writel(val, reg + pll_video_regs[i]); > + } > + > + /* Enforce m1 = 0, m0 = 1 for Audio PLL */ Why? > + val = readl(reg + SUN50I_A100_PLL_AUDIO_REG); > + val &= ~BIT(1); > + val |= BIT(0); > + writel(val, reg + SUN50I_A100_PLL_AUDIO_REG); > + > + /* > + * Force OHCI 12M clock sources to 00 (12MHz divided from 48MHz) > + * > + * This clock mux is still mysterious, and the code just enforces > + * it to have a valid clock parent. > + */ > + for (i = 0; i < ARRAY_SIZE(usb2_clk_regs); i++) { > + val = readl(reg + usb2_clk_regs[i]); > + val &= ~GENMASK(25, 24); > + writel(val, reg + usb2_clk_regs[i]); > + } > + > + ret = sunxi_ccu_probe(pdev->dev.of_node, reg, &sun50i_a100_ccu_desc); > + if (ret) > + return ret; > + > + /* Gate then ungate PLL CPU after any rate changes */ > + ccu_pll_notifier_register(&sun50i_a100_pll_cpu_nb); > + > + /* Reparent CPU during PLL CPU rate changes */ > + ccu_mux_notifier_register(pll_cpux_clk.common.hw.clk, > + &sun50i_a100_cpu_nb); > + > + return 0; > +} > + > +static const struct of_device_id sun50i_a100_ccu_ids[] = { > + { .compatible = "allwinner,sun50i-a100-ccu" }, > + { } > +}; > + > +static struct platform_driver sun50i_a100_ccu_driver = { > + .probe = sun50i_a100_ccu_probe, > + .driver = { > + .name = "sun50i-a100-ccu", > + .of_match_table = sun50i_a100_ccu_ids, > + }, > +}; > +module_platform_driver(sun50i_a100_ccu_driver); > diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100.h b/drivers/clk/sunxi-ng/ccu-sun50i-a100.h > new file mode 100644 > index 000000000000..4fbf2e1a6697 > --- /dev/null > +++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100.h > @@ -0,0 +1,14 @@ > +/* SPDX-License-Identifier: GPL-2.0 */ > +/* > + * Copyright (c) 2020 Frank Lee <frank@allwinner.com> > + */ > + > +#ifndef _CCU_SUN50I_A100_H_ > +#define _CCU_SUN50I_A100_H_ > + > +#include <dt-bindings/clock/sun50i-a100-ccu.h> > +#include <dt-bindings/reset/sun50i-a100-ccu.h> > + > +#define CLK_NUMBER (CLK_CSI_ISP + 1) > + > +#endif /* _CCU_SUN50I_A100_H_ */ > diff --git a/include/dt-bindings/clock/sun50i-a100-ccu.h b/include/dt-bindings/clock/sun50i-a100-ccu.h > new file mode 100644 > index 000000000000..8186b1a7bcfe > --- /dev/null > +++ b/include/dt-bindings/clock/sun50i-a100-ccu.h > @@ -0,0 +1,141 @@ > +/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */ > +/* > + * Copyright (c) 2020 Frank Lee <frank@allwinner.com> > + */ > + > +#ifndef _DT_BINDINGS_CLK_SUN50I_A100_H_ > +#define _DT_BINDINGS_CLK_SUN50I_A100_H_ > + > +#define CLK_OSC12M 0 > +#define CLK_PLL_CPUX 1 > +#define CLK_PLL_DDR0 2 > +#define CLK_PLL_PERIPH0 3 > +#define CLK_PLL_PERIPH0_2X 4 > +#define CLK_PLL_PERIPH1 5 > +#define CLK_PLL_PERIPH1_2X 6 > +#define CLK_PLL_GPU 7 > +#define CLK_PLL_VIDEO0 8 > +#define CLK_PLL_VIDEO0_2X 9 > +#define CLK_PLL_VIDEO0_4X 10 > +#define CLK_PLL_VIDEO1 11 > +#define CLK_PLL_VIDEO1_2X 12 > +#define CLK_PLL_VIDEO1_4X 13 > +#define CLK_PLL_VIDEO2 14 > +#define CLK_PLL_VIDEO2_2X 15 > +#define CLK_PLL_VIDEO2_4X 16 > +#define CLK_PLL_VIDEO3 17 > +#define CLK_PLL_VIDEO3_2X 18 > +#define CLK_PLL_VIDEO3_4X 19 > +#define CLK_PLL_VE 20 > +#define CLK_PLL_COM 21 > +#define CLK_PLL_COM_AUDIO 22 > +#define CLK_PLL_AUDIO 23 > +#define CLK_CPUX 24 > +#define CLK_AXI 25 > +#define CLK_CPUX_APB 26 > +#define CLK_PSI_AHB1_AHB2 27 > +#define CLK_AHB3 28 > +#define CLK_APB1 29 > +#define CLK_APB2 30 > +#define CLK_MBUS 31 > +#define CLK_DE 32 > +#define CLK_BUS_DE 33 > +#define CLK_G2D 34 > +#define CLK_BUS_G2D 35 > +#define CLK_GPU 36 > +#define CLK_BUS_GPU 37 > +#define CLK_CE 38 > +#define CLK_BUS_CE 39 > +#define CLK_VE 40 > +#define CLK_BUS_VE 41 > +#define CLK_BUS_DMA 42 > +#define CLK_BUS_MSGBOX 43 > +#define CLK_BUS_SPINLOCK 44 > +#define CLK_BUS_HSTIMER 45 > +#define CLK_AVS 46 > +#define CLK_BUS_DBG 47 > +#define CLK_BUS_PSI 48 > +#define CLK_BUS_PWM 49 > +#define CLK_BUS_IOMMU 50 > +#define CLK_MBUS_DMA 51 > +#define CLK_MBUS_VE 52 > +#define CLK_MBUS_CE 53 > +#define CLK_MBUS_NAND 54 > +#define CLK_MBUS_CSI 55 > +#define CLK_MBUS_ISP 56 > +#define CLK_MBUS_G2D 57 > +#define CLK_BUS_DRAM 58 > +#define CLK_NAND0 59 > +#define CLK_NAND1 60 > +#define CLK_BUS_NAND 61 > +#define CLK_MMC0 62 > +#define CLK_MMC1 63 > +#define CLK_MMC2 64 > +#define CLK_MMC3 65 > +#define CLK_BUS_MMC0 66 > +#define CLK_BUS_MMC1 67 > +#define CLK_BUS_MMC2 68 > +#define CLK_BUS_UART0 69 > +#define CLK_BUS_UART1 70 > +#define CLK_BUS_UART2 71 > +#define CLK_BUS_UART3 72 > +#define CLK_BUS_UART4 73 > +#define CLK_BUS_I2C0 74 > +#define CLK_BUS_I2C1 75 > +#define CLK_BUS_I2C2 76 > +#define CLK_BUS_I2C3 77 > +#define CLK_SPI0 78 > +#define CLK_SPI1 79 > +#define CLK_SPI2 80 > +#define CLK_BUS_SPI0 81 > +#define CLK_BUS_SPI1 82 > +#define CLK_BUS_SPI2 83 > +#define CLK_EMAC_25M 84 > +#define CLK_BUS_EMAC 85 > +#define CLK_IR_RX 86 > +#define CLK_BUS_IR_RX 87 > +#define CLK_IR_TX 88 > +#define CLK_BUS_IR_TX 89 > +#define CLK_BUS_GPADC 90 > +#define CLK_BUS_THS 91 > +#define CLK_I2S0 92 > +#define CLK_I2S1 93 > +#define CLK_I2S2 94 > +#define CLK_I2S3 95 > +#define CLK_BUS_I2S0 96 > +#define CLK_BUS_I2S1 97 > +#define CLK_BUS_I2S2 98 > +#define CLK_BUS_I2S3 99 > +#define CLK_SPDIF 100 > +#define CLK_BUS_SPDIF 101 > +#define CLK_DMIC 102 > +#define CLK_BUS_DMIC 103 > +#define CLK_AUDIO_DAC 104 > +#define CLK_AUDIO_ADC 105 > +#define CLK_AUDIO_4X 106 > +#define CLK_BUS_AUDIO_CODEC 107 > +#define CLK_USB_OHCI0 108 > +#define CLK_USB_PHY0 109 > +#define CLK_USB_OHCI1 110 > +#define CLK_USB_PHY1 111 > +#define CLK_BUS_OHCI0 112 > +#define CLK_BUS_OHCI1 113 > +#define CLK_BUS_EHCI0 114 > +#define CLK_BUS_EHCI1 115 > +#define CLK_BUS_OTG 116 > +#define CLK_BUS_LRADC 117 > +#define CLK_BUS_DPSS_TOP0 118 > +#define CLK_BUS_DPSS_TOP1 119 > +#define CLK_MIPI_DSI 120 > +#define CLK_BUS_MIPI_DSI 121 > +#define CLK_TCON_LCD 122 > +#define CLK_BUS_TCON_LCD 123 > +#define CLK_LEDC 124 > +#define CLK_BUS_LEDC 125 > +#define CLK_CSI_TOP 126 > +#define CLK_CSI0_MCLK 127 > +#define CLK_CSI1_MCLK 128 > +#define CLK_BUS_CSI 129 > +#define CLK_CSI_ISP 130 > + > +#endif /* _DT_BINDINGS_CLK_SUN50I_A100_H_ */ So we don't really want to expose all the clocks in the binding here, but only the one that are going to be used by the devices (and not the "internal" ones), so that will be usually the bus gates and the module gates. If we need a PLL at some point, we can always export it, but that should be the exception, not the default. > diff --git a/include/dt-bindings/clock/sun50i-a100-r-ccu.h b/include/dt-bindings/clock/sun50i-a100-r-ccu.h > new file mode 100644 > index 000000000000..a4486c31924a > --- /dev/null > +++ b/include/dt-bindings/clock/sun50i-a100-r-ccu.h > @@ -0,0 +1,25 @@ > +/* SPDX-License-Identifier: GPL-2.0 */ > +/* > + * Copyright (c) 2020 Frank Lee <frank@allwinner.com> > + */ > + > +#ifndef _DT_BINDINGS_CLK_SUN50I_A100_R_CCU_H_ > +#define _DT_BINDINGS_CLK_SUN50I_A100_R_CCU_H_ > + > +#define CLK_CPUS 0 > +#define CLK_R_AHB 1 > +#define CLK_R_APB1 2 > +#define CLK_R_APB2 3 > +#define CLK_R_APB1_TIMER 4 > +#define CLK_R_APB1_TWD 5 > +#define CLK_R_APB1_PWM 6 > +#define CLK_R_APB1_BUS_PWM 7 > +#define CLK_R_APB1_PPU 8 > +#define CLK_R_APB2_UART 9 > +#define CLK_R_APB2_I2C0 10 > +#define CLK_R_APB2_I2C1 11 > +#define CLK_R_APB1_IR 12 > +#define CLK_R_APB1_BUS_IR 13 > +#define CLK_R_AHB_BUS_RTC 14 > + > +#endif /* _DT_BINDINGS_CLK_SUN50I_A100_R_CCU_H_ */ Same story here Maxime [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 228 bytes --] ^ permalink raw reply [flat|nested] 15+ messages in thread
* 回复：[PATCH 1/4] clk: sunxi-ng: add support for the Allwinner A100 CCU 2020-05-22 15:14 ` Maxime Ripard @ 2020-06-03 9:42 ` 李扬韬 2020-06-03 9:48 ` [PATCH " Chen-Yu Tsai 0 siblings, 1 reply; 15+ messages in thread From: 李扬韬 @ 2020-06-03 9:42 UTC (permalink / raw) To: Maxime Ripard Cc: wens, robh+dt, mturquette, sboyd, linus.walleij, p.zabel, 黄烁生, tiny.windzz, linux-arm-kernel, devicetree, linux-kernel, linux-clk, linux-gpio >> + /* Enable the lock bits on all PLLs */ >> + for (i = 0; i < ARRAY_SIZE(pll_regs); i++) { >> + val = readl(reg + pll_regs[i]); >> + val |= BIT(29); > >Having a define for that would be nice here > >> + writel(val, reg + pll_regs[i]); >> + } >> + >> + /* >> + * In order to pass the EMI certification, the SDM function of >> + * the peripheral 1 bus is enabled, and the frequency is still >> + * calculated using the previous division factor. >> + */ >> + writel(0xd1303333, reg + SUN50I_A100_PLL_PERIPH1_PATTERN0_REG); > >Same here Having a define? I don’t quite understand what you mean, can you give me an example? MBR, Yangtao ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH 1/4] clk: sunxi-ng: add support for the Allwinner A100 CCU 2020-06-03 9:42 ` 回复：[PATCH " 李扬韬 @ 2020-06-03 9:48 ` Chen-Yu Tsai 0 siblings, 0 replies; 15+ messages in thread From: Chen-Yu Tsai @ 2020-06-03 9:48 UTC (permalink / raw) To: 李扬韬 Cc: Maxime Ripard, robh+dt, mturquette, sboyd, linus.walleij, p.zabel, 黄烁生, tiny.windzz, linux-arm-kernel, devicetree, linux-kernel, linux-clk, linux-gpio On Wed, Jun 3, 2020 at 5:42 PM 李扬韬 <frank@allwinnertech.com> wrote: > > >> + /* Enable the lock bits on all PLLs */ > >> + for (i = 0; i < ARRAY_SIZE(pll_regs); i++) { > >> + val = readl(reg + pll_regs[i]); > >> + val |= BIT(29); > > > >Having a define for that would be nice here > > > >> + writel(val, reg + pll_regs[i]); > >> + } > >> + > >> + /* > >> + * In order to pass the EMI certification, the SDM function of > >> + * the peripheral 1 bus is enabled, and the frequency is still > >> + * calculated using the previous division factor. > >> + */ > >> + writel(0xd1303333, reg + SUN50I_A100_PLL_PERIPH1_PATTERN0_REG); > > > >Same here > > Having a define? I don’t quite understand what you mean, > can you give me an example? What Maxime means is that 0xd1303333 is a magic number. It is better to make a properly named macro, or many macros that you then bitwise-OR together. So you should make macros for each bitfield in that register, which would likely include the SDM calculation factors, the enable bit, and any other fields. ChenYu > MBR, > Yangtao ^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 2/4] pinctrl: sunxi: add support for the Allwinner A100 pin controller 2020-05-22 3:07 [PATCH 0/4] Allwinner A100 Initial support Frank Lee 2020-05-22 3:07 ` [PATCH 1/4] clk: sunxi-ng: add support for the Allwinner A100 CCU Frank Lee @ 2020-05-22 3:07 ` Frank Lee 2020-05-22 15:28 ` Maxime Ripard 2020-05-22 3:07 ` [PATCH 3/4] arm64: allwinner: A100: add the basical Allwinner A100 DTSI file Frank Lee ` (2 subsequent siblings) 4 siblings, 1 reply; 15+ messages in thread From: Frank Lee @ 2020-05-22 3:07 UTC (permalink / raw) To: mripard, wens, robh+dt, mturquette, sboyd, linus.walleij, p.zabel, frank, huangshuosheng, tiny.windzz Cc: linux-arm-kernel, devicetree, linux-kernel, linux-clk, linux-gpio This commit introduces support for the pin controller on A100. Signed-off-by: Frank Lee <frank@allwinnertech.com> --- drivers/pinctrl/sunxi/Kconfig | 10 + drivers/pinctrl/sunxi/Makefile | 2 + drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c | 105 +++ drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c | 710 ++++++++++++++++++ 4 files changed, 827 insertions(+) create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig index f7aae200ee15..593293584ecc 100644 --- a/drivers/pinctrl/sunxi/Kconfig +++ b/drivers/pinctrl/sunxi/Kconfig @@ -94,6 +94,16 @@ config PINCTRL_SUN50I_A64_R default ARM64 && ARCH_SUNXI select PINCTRL_SUNXI +config PINCTRL_SUN50I_A100 + bool "Support for the Allwinner A100 PIO" + default ARM64 && ARCH_SUNXI + select PINCTRL_SUNXI + +config PINCTRL_SUN50I_A100_R + bool "Support for the Allwinner A100 R-PIO" + default ARM64 && ARCH_SUNXI + select PINCTRL_SUNXI + config PINCTRL_SUN50I_H5 bool "Support for the Allwinner H5 PIO" default ARM64 && ARCH_SUNXI diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile index fafcdae8134f..8b7ff0dc3bdf 100644 --- a/drivers/pinctrl/sunxi/Makefile +++ b/drivers/pinctrl/sunxi/Makefile @@ -13,6 +13,8 @@ obj-$(CONFIG_PINCTRL_SUN8I_A23_R) += pinctrl-sun8i-a23-r.o obj-$(CONFIG_PINCTRL_SUN8I_A33) += pinctrl-sun8i-a33.o obj-$(CONFIG_PINCTRL_SUN50I_A64) += pinctrl-sun50i-a64.o obj-$(CONFIG_PINCTRL_SUN50I_A64_R) += pinctrl-sun50i-a64-r.o +obj-$(CONFIG_PINCTRL_SUN50I_A100) += pinctrl-sun50i-a100.o +obj-$(CONFIG_PINCTRL_SUN50I_A100_R) += pinctrl-sun50i-a100-r.o obj-$(CONFIG_PINCTRL_SUN8I_A83T) += pinctrl-sun8i-a83t.o obj-$(CONFIG_PINCTRL_SUN8I_A83T_R) += pinctrl-sun8i-a83t-r.o obj-$(CONFIG_PINCTRL_SUN8I_H3) += pinctrl-sun8i-h3.o diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c new file mode 100644 index 000000000000..d38d8770c9da --- /dev/null +++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c @@ -0,0 +1,105 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2020 Frank Lee <frank@allwinner.com> + * + * Based on: + * huangshuosheng <huangshuosheng@allwinnertech.com> + */ + +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/pinctrl/pinctrl.h> +#include "pinctrl-sunxi.h" + +static const struct sunxi_desc_pin a100_r_pins[] = { + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 0), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "s_i2c0"), /* SCK */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 1), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "s_i2c0"), /* SDA */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 2), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "s_uart0"), /* TX */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 3), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "s_uart0"), /* RX */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 4), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "s_jtag"), /* MS */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 5), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "s_jtag"), /* CK */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 6), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "s_jtag"), /* DO */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 7), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "s_jtag"), /* DI */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 8), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "s_i2c1"), /* SCK */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 9), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "s_i2c1"), /* SDA */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 10), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "s_pwm"), + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 11), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "s_cpu"), /* CUR_W */ + SUNXI_FUNCTION(0x3, "s_cir"), /* IN */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)), +}; + +static const struct sunxi_pinctrl_desc a100_r_pinctrl_data = { + .pins = a100_r_pins, + .npins = ARRAY_SIZE(a100_r_pins), + .pin_base = PL_BASE, + .irq_banks = 1, +}; + +static int a100_r_pinctrl_probe(struct platform_device *pdev) +{ + return sunxi_pinctrl_init(pdev, &a100_r_pinctrl_data); +} + +static const struct of_device_id a100_r_pinctrl_match[] = { + { .compatible = "allwinner,sun50i-a100-r-pinctrl", }, + {} +}; +MODULE_DEVICE_TABLE(of, a100_r_pinctrl_match); + +static struct platform_driver a100_r_pinctrl_driver = { + .probe = a100_r_pinctrl_probe, + .driver = { + .name = "sun50iw10p1-r-pinctrl", + .of_match_table = a100_r_pinctrl_match, + }, +}; +module_platform_driver(a100_r_pinctrl_driver); diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c new file mode 100644 index 000000000000..b9591009f0a4 --- /dev/null +++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c @@ -0,0 +1,710 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2020 Frank Lee <frank@allwinner.com> + * + * Based on: + * huangshuosheng <huangshuosheng@allwinnertech.com> + */ + +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/pinctrl/pinctrl.h> + +#include "pinctrl-sunxi.h" + +static const struct sunxi_desc_pin a100_pins[] = { + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 0), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "uart2"), /* TX */ + SUNXI_FUNCTION(0x3, "spi2"), /* CS */ + SUNXI_FUNCTION(0x4, "jtag"), /* MS */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 1), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "uart2"), /* RX */ + SUNXI_FUNCTION(0x3, "spi2"), /* CLK */ + SUNXI_FUNCTION(0x4, "jtag"), /* CK */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 2), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "uart2"), /* RTS */ + SUNXI_FUNCTION(0x3, "spi2"), /* MOSI */ + SUNXI_FUNCTION(0x4, "jtag"), /* DO */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 3), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "uart2"), /* CTS */ + SUNXI_FUNCTION(0x3, "spi2"), /* MISO */ + SUNXI_FUNCTION(0x4, "jtag"), /* DI */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 4), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "i2c1"), /* SCK */ + SUNXI_FUNCTION(0x3, "i2s0"), /* MCLK */ + SUNXI_FUNCTION(0x4, "jtag"), /* MS_GPU */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 5), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "i2c1"), /* SDA */ + SUNXI_FUNCTION(0x3, "i2s0"), /* BCLK */ + SUNXI_FUNCTION(0x4, "jtag"), /* CK_GPU */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 6), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x3, "i2s0"), /* LRCK */ + SUNXI_FUNCTION(0x4, "jtag"), /* DO_GPU */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 7), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "spdif"), /* DIN */ + SUNXI_FUNCTION(0x3, "i2s0"), /* DOUT0 */ + SUNXI_FUNCTION(0x4, "i2s0"), /* DIN1 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 8), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "spdif"), /* DOUT */ + SUNXI_FUNCTION(0x3, "i2s0"), /* DIN0 */ + SUNXI_FUNCTION(0x4, "i2s0"), /* DOUT1 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 9), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "uart0"), /* TX */ + SUNXI_FUNCTION(0x3, "i2c0"), /* SCK */ + SUNXI_FUNCTION(0x4, "jtag"), /* DI_GPU */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 10), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "uart0"), /* RX */ + SUNXI_FUNCTION(0x3, "i2c0"), /* SDA */ + SUNXI_FUNCTION(0x4, "pwm1"), + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)), + /* HOLE */ + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "nand0"), /* WE */ + SUNXI_FUNCTION(0x3, "mmc2"), /* DS */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 0)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "nand0"), /* ALE */ + SUNXI_FUNCTION(0x3, "mmc2"), /* RST */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 1)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "nand0"), /* CLE */ + SUNXI_FUNCTION(0x4, "spi0"), /* MOSI */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 2)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "nand0"), /* CE1 */ + SUNXI_FUNCTION(0x4, "spi0"), /* CS0 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 3)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "nand0"), /* CE0 */ + SUNXI_FUNCTION(0x4, "spi0"), /* MISO */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 4)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "nand0"), /* RE */ + SUNXI_FUNCTION(0x3, "mmc2"), /* CLK */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 5)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "nand0"), /* RB0 */ + SUNXI_FUNCTION(0x3, "mmc2"), /* CMD */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 6)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "nand0"), /* RB1 */ + SUNXI_FUNCTION(0x4, "spi0"), /* CS1 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 7)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "nand0"), /* DQ7 */ + SUNXI_FUNCTION(0x3, "mmc2"), /* D3 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 8)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "nand0"), /* DQ6 */ + SUNXI_FUNCTION(0x3, "mmc2"), /* D4 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 9)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "nand0"), /* DQ5 */ + SUNXI_FUNCTION(0x3, "mmc2"), /* D0 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 10)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "nand0"), /* DQ4 */ + SUNXI_FUNCTION(0x3, "mmc2"), /* D5 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 11)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "nand0"), /* DQS */ + SUNXI_FUNCTION(0x4, "spi0"), /* CLK */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 12)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "nand0"), /* DQ3 */ + SUNXI_FUNCTION(0x3, "mmc2"), /* D1 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 13)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "nand0"), /* DQ2 */ + SUNXI_FUNCTION(0x3, "mmc2"), /* D6 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 14)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "nand0"), /* DQ1 */ + SUNXI_FUNCTION(0x3, "mmc2"), /* D2 */ + SUNXI_FUNCTION(0x4, "spi0"), /* WP */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 15)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "nand0"), /* DQ0 */ + SUNXI_FUNCTION(0x3, "mmc2"), /* D7 */ + SUNXI_FUNCTION(0x4, "spi0"), /* HOLD */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 16)), + /* HOLE */ + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* D2 */ + SUNXI_FUNCTION(0x3, "lvds0"), /* D0P */ + SUNXI_FUNCTION(0x4, "dsi0"), /* DP0 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 0)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* D3 */ + SUNXI_FUNCTION(0x3, "lvds0"), /* D0N */ + SUNXI_FUNCTION(0x4, "dsi0"), /* DM0 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 1)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* D4 */ + SUNXI_FUNCTION(0x3, "lvds0"), /* D1P */ + SUNXI_FUNCTION(0x4, "dsi0"), /* DP1 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 2)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* D5 */ + SUNXI_FUNCTION(0x3, "lvds0"), /* D1N */ + SUNXI_FUNCTION(0x4, "dsi0"), /* DM1 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 3)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* D6 */ + SUNXI_FUNCTION(0x3, "lvds0"), /* D2P */ + SUNXI_FUNCTION(0x4, "dsi0"), /* CKP */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 4)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* D7 */ + SUNXI_FUNCTION(0x3, "lvds0"), /* D2N */ + SUNXI_FUNCTION(0x4, "dsi0"), /* CKM */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 5)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* D10 */ + SUNXI_FUNCTION(0x3, "lvds0"), /* CKP */ + SUNXI_FUNCTION(0x4, "dsi0"), /* DP2 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 6)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* D11 */ + SUNXI_FUNCTION(0x3, "lvds0"), /* CKN */ + SUNXI_FUNCTION(0x4, "dsi0"), /* DM2 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 7)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* D12 */ + SUNXI_FUNCTION(0x4, "dsi0"), /* DP3 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 8)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* D13 */ + SUNXI_FUNCTION(0x4, "dsi0"), /* DM3 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 9)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* D14 */ + SUNXI_FUNCTION(0x4, "spi1"), /* CS */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 10)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* D15 */ + SUNXI_FUNCTION(0x4, "spi1"), /* CLK */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 11)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* D18 */ + SUNXI_FUNCTION(0x4, "spi1"), /* MOSI */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 12)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* D19 */ + SUNXI_FUNCTION(0x4, "spi1"), /* MISO */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 13)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* D20 */ + SUNXI_FUNCTION(0x4, "uart3"), /* TX */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 14)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* D21 */ + SUNXI_FUNCTION(0x4, "uart3"), /* RX */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 15)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* D22 */ + SUNXI_FUNCTION(0x4, "uart3"), /* RTS */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 16)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* D23 */ + SUNXI_FUNCTION(0x4, "uart3"), /* CTS */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 17)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 18), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* CLK */ + SUNXI_FUNCTION(0x4, "uart4"), /* TX */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 18)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 19), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* DE */ + SUNXI_FUNCTION(0x4, "uart4"), /* RX */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 19)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 20), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* HSYNC */ + SUNXI_FUNCTION(0x3, "pwm2"), + SUNXI_FUNCTION(0x4, "uart4"), /* RTS */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 20)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 21), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "lcd0"), /* VSYNC */ + SUNXI_FUNCTION(0x3, "pwm3"), + SUNXI_FUNCTION(0x4, "uart4"), /* CTS */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 21)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 22), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "pwm1"), + SUNXI_FUNCTION(0x4, "i2c0"), /* SCK */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 22)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 23), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "pwm0"), + SUNXI_FUNCTION(0x4, "i2c0"), /* SDA */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 23)), + /* HOLE */ + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "csi"), /* MCLK */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 0)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "i2c2"), /* SCK */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 1)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "i2c2"), /* SDA */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 2)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "i2c3"), /* SCK */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 3)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "i2c3"), /* SDA */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 4)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "csi"), /* MCLK */ + SUNXI_FUNCTION(0x3, "pll"), /* LOCK_DBG */ + SUNXI_FUNCTION(0x4, "i2s2"), /* MCLK */ + SUNXI_FUNCTION(0x5, "ledc"), /* LEDC */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 5)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x3, "bist0"), /* RESULT0 */ + SUNXI_FUNCTION(0x4, "i2s2"), /* BCLK */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 6)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "csi"), /* SM_VS */ + SUNXI_FUNCTION(0x3, "bist0"), /* RESULT1 */ + SUNXI_FUNCTION(0x4, "i2s2"), /* LRCK */ + SUNXI_FUNCTION(0x5, "tcon0"), /* TRIG */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 7)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x3, "bist0"), /* RESULT2 */ + SUNXI_FUNCTION(0x4, "i2s2"), /* DOUT0 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 8)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x3, "bist0"), /* RESULT3 */ + SUNXI_FUNCTION(0x4, "i2s2"), /* DIN0 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 9)), + /* HOLE */ + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "mmc0"), /* D1 */ + SUNXI_FUNCTION(0x3, "jtag"), /* MS1 */ + SUNXI_FUNCTION(0x4, "jtag"), /* MS_GPU */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 0)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "mmc0"), /* D0 */ + SUNXI_FUNCTION(0x3, "jtag"), /* DI1 */ + SUNXI_FUNCTION(0x4, "jtag"), /* DI_GPU */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 1)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "mmc0"), /* CLK */ + SUNXI_FUNCTION(0x3, "uart0"), /* TX */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 2)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "mmc0"), /* CMD */ + SUNXI_FUNCTION(0x3, "jtag"), /* DO */ + SUNXI_FUNCTION(0x4, "jtag"), /* DO_GPU */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 3)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "mmc0"), /* D3 */ + SUNXI_FUNCTION(0x3, "uart0"), /* RX */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 4)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "mmc0"), /* D2 */ + SUNXI_FUNCTION(0x3, "jtag"), /* CK */ + SUNXI_FUNCTION(0x4, "jtag"), /* CK_GPU */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 5)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 6)), + /* HOLE */ + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "mmc1"), /* CLK */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 0)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "mmc1"), /* CMD */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 1)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "mmc1"), /* D0 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 2)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "mmc1"), /* D1 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 3)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "mmc1"), /* D2 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 4)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "mmc1"), /* D3 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 5)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "uart1"), /* TX */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 6)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "uart1"), /* RX */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 7)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "uart1"), /* RTS */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 8)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "uart1"), /* CTS */ + SUNXI_FUNCTION(0x3, "i2s1"), /* MCLK */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 9)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x3, "i2s1"), /* BCLK */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 10)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x3, "i2s1"), /* LRCK */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 11)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x3, "i2s1"), /* DOUT0 */ + SUNXI_FUNCTION(0x4, "i2s1"), /* DIN1 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 12)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x3, "i2s1"), /* DIN0 */ + SUNXI_FUNCTION(0x4, "i2s1"), /* DOUT1 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 13)), + /* HOLE */ + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 0), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "i2c0"), /* SCK */ + SUNXI_FUNCTION(0x5, "emac0"), /* RXD1 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 0)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 1), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "i2c0"), /* SDA */ + SUNXI_FUNCTION(0x5, "emac0"), /* RXD0 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 1)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 2), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "i2c1"), /* SCK */ + SUNXI_FUNCTION(0x3, "cpu"), /* CUR_W */ + SUNXI_FUNCTION(0x5, "emac0"), /* RXCTL */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 2)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 3), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "i2c1"), /* SDA */ + SUNXI_FUNCTION(0x3, "cir0"), /* OUT */ + SUNXI_FUNCTION(0x5, "emac0"), /* CLKIN */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 3)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 4), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "uart3"), /* TX */ + SUNXI_FUNCTION(0x3, "spi1"), /* CS */ + SUNXI_FUNCTION(0x4, "cpu"), /* CUR_W */ + SUNXI_FUNCTION(0x5, "emac0"), /* TXD1 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 4)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 5), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "uart3"), /* RX */ + SUNXI_FUNCTION(0x3, "spi1"), /* CLK */ + SUNXI_FUNCTION(0x4, "ledc"), + SUNXI_FUNCTION(0x5, "emac0"), /* TXD0 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 5)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 6), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "uart3"), /* RTS */ + SUNXI_FUNCTION(0x3, "spi1"), /* MOSI */ + SUNXI_FUNCTION(0x5, "emac0"), /* TXCK */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 6)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 7), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "uart3"), /* CTS */ + SUNXI_FUNCTION(0x3, "spi1"), /* MISO */ + SUNXI_FUNCTION(0x4, "spdif"), /* OUT */ + SUNXI_FUNCTION(0x5, "emac0"), /* TXCTL */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 7)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 8), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "dmic"), /* CLK */ + SUNXI_FUNCTION(0x3, "spi2"), /* CS */ + SUNXI_FUNCTION(0x4, "i2s2"), /* MCLK */ + SUNXI_FUNCTION(0x5, "i2s2"), /* DIN2 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 8)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 9), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "dmic"), /* DATA0 */ + SUNXI_FUNCTION(0x3, "spi2"), /* CLK */ + SUNXI_FUNCTION(0x4, "i2s2"), /* BCLK */ + SUNXI_FUNCTION(0x5, "emac0"), /* MDC */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 9)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 10), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "dmic"), /* DATA1 */ + SUNXI_FUNCTION(0x3, "spi2"), /* MOSI */ + SUNXI_FUNCTION(0x4, "i2s2"), /* LRCK */ + SUNXI_FUNCTION(0x5, "emac0"), /* MDIO */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 10)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 11), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "dmic"), /* DATA2 */ + SUNXI_FUNCTION(0x3, "spi2"), /* MISO */ + SUNXI_FUNCTION(0x4, "i2s2"), /* DOUT0 */ + SUNXI_FUNCTION(0x5, "i2s2"), /* DIN1 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 11)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 12), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "dmic"), /* DATA3 */ + SUNXI_FUNCTION(0x3, "i2c3"), /* SCK */ + SUNXI_FUNCTION(0x4, "i2s2"), /* DIN0 */ + SUNXI_FUNCTION(0x5, "i2s2"), /* DOUT1 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 12)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 13), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x3, "i2c3"), /* SCK */ + SUNXI_FUNCTION(0x4, "i2s3"), /* MCLK */ + SUNXI_FUNCTION(0x5, "emac0"), /* EPHY */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 13)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 14), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x4, "i2s3"), /* BCLK */ + SUNXI_FUNCTION(0x5, "emac0"), /* RXD3 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 14)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 15), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x4, "i2s3"), /* LRCK */ + SUNXI_FUNCTION(0x5, "emac0"), /* RXD2 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 15)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 16), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x3, "i2s3"), /* DOUT0 */ + SUNXI_FUNCTION(0x4, "i2s3"), /* DIN1 */ + SUNXI_FUNCTION(0x5, "emac0"), /* RXCK */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 16)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 17), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x3, "i2s3"), /* DOUT1 */ + SUNXI_FUNCTION(0x4, "i2s3"), /* DIN0 */ + SUNXI_FUNCTION(0x5, "emac0"), /* TXD3 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 17)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 18), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "cir0"), /* OUT */ + SUNXI_FUNCTION(0x3, "i2s3"), /* DOUT2 */ + SUNXI_FUNCTION(0x4, "i2s3"), /* DIN2 */ + SUNXI_FUNCTION(0x5, "emac0"), /* TXD2 */ + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 18)), + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 19), + SUNXI_FUNCTION(0x0, "gpio_in"), + SUNXI_FUNCTION(0x1, "gpio_out"), + SUNXI_FUNCTION(0x2, "cir0"), /* IN */ + SUNXI_FUNCTION(0x3, "i2s3"), /* DOUT3 */ + SUNXI_FUNCTION(0x4, "i2s3"), /* DIN3 */ + SUNXI_FUNCTION(0x5, "ledc"), + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 19)), +}; + +static const unsigned int a100_irq_bank_map[] = { 0, 1, 2, 3, 4, 5, 6}; + +static const struct sunxi_pinctrl_desc a100_pinctrl_data = { + .pins = a100_pins, + .npins = ARRAY_SIZE(a100_pins), + .irq_banks = 7, + .irq_bank_map = a100_irq_bank_map, + .io_bias_cfg_variant = BIAS_VOLTAGE_PIO_POW_MODE_SEL, +}; + +static int a100_pinctrl_probe(struct platform_device *pdev) +{ + return sunxi_pinctrl_init(pdev, &a100_pinctrl_data); +} + +static const struct of_device_id a100_pinctrl_match[] = { + { .compatible = "allwinner,sun50i-a100-pinctrl", }, + {} +}; +MODULE_DEVICE_TABLE(of, a100_pinctrl_match); + +static struct platform_driver a100_pinctrl_driver = { + .probe = a100_pinctrl_probe, + .driver = { + .name = "sun50i-a100-pinctrl", + .of_match_table = a100_pinctrl_match, + }, +}; +module_platform_driver(a100_pinctrl_driver); -- 2.24.0 ^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: [PATCH 2/4] pinctrl: sunxi: add support for the Allwinner A100 pin controller 2020-05-22 3:07 ` [PATCH 2/4] pinctrl: sunxi: add support for the Allwinner A100 pin controller Frank Lee @ 2020-05-22 15:28 ` Maxime Ripard 2020-06-03 9:44 ` 回复：[PATCH " 李扬韬 0 siblings, 1 reply; 15+ messages in thread From: Maxime Ripard @ 2020-05-22 15:28 UTC (permalink / raw) To: Frank Lee Cc: wens, robh+dt, mturquette, sboyd, linus.walleij, p.zabel, huangshuosheng, tiny.windzz, linux-arm-kernel, devicetree, linux-kernel, linux-clk, linux-gpio [-- Attachment #1: Type: text/plain, Size: 35314 bytes --] Hi, On Fri, May 22, 2020 at 11:07:41AM +0800, Frank Lee wrote: > This commit introduces support for the pin controller on A100. > > Signed-off-by: Frank Lee <frank@allwinnertech.com> > --- > drivers/pinctrl/sunxi/Kconfig | 10 + > drivers/pinctrl/sunxi/Makefile | 2 + > drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c | 105 +++ > drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c | 710 ++++++++++++++++++ This will need a DT binding too, and please make sure to run checkpatch with --strict, you have a bunch of misaligned parenthesis. > 4 files changed, 827 insertions(+) > create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c > create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c > > diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig > index f7aae200ee15..593293584ecc 100644 > --- a/drivers/pinctrl/sunxi/Kconfig > +++ b/drivers/pinctrl/sunxi/Kconfig > @@ -94,6 +94,16 @@ config PINCTRL_SUN50I_A64_R > default ARM64 && ARCH_SUNXI > select PINCTRL_SUNXI > > +config PINCTRL_SUN50I_A100 > + bool "Support for the Allwinner A100 PIO" > + default ARM64 && ARCH_SUNXI > + select PINCTRL_SUNXI > + > +config PINCTRL_SUN50I_A100_R > + bool "Support for the Allwinner A100 R-PIO" > + default ARM64 && ARCH_SUNXI > + select PINCTRL_SUNXI > + > config PINCTRL_SUN50I_H5 > bool "Support for the Allwinner H5 PIO" > default ARM64 && ARCH_SUNXI > diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile > index fafcdae8134f..8b7ff0dc3bdf 100644 > --- a/drivers/pinctrl/sunxi/Makefile > +++ b/drivers/pinctrl/sunxi/Makefile > @@ -13,6 +13,8 @@ obj-$(CONFIG_PINCTRL_SUN8I_A23_R) += pinctrl-sun8i-a23-r.o > obj-$(CONFIG_PINCTRL_SUN8I_A33) += pinctrl-sun8i-a33.o > obj-$(CONFIG_PINCTRL_SUN50I_A64) += pinctrl-sun50i-a64.o > obj-$(CONFIG_PINCTRL_SUN50I_A64_R) += pinctrl-sun50i-a64-r.o > +obj-$(CONFIG_PINCTRL_SUN50I_A100) += pinctrl-sun50i-a100.o > +obj-$(CONFIG_PINCTRL_SUN50I_A100_R) += pinctrl-sun50i-a100-r.o > obj-$(CONFIG_PINCTRL_SUN8I_A83T) += pinctrl-sun8i-a83t.o > obj-$(CONFIG_PINCTRL_SUN8I_A83T_R) += pinctrl-sun8i-a83t-r.o > obj-$(CONFIG_PINCTRL_SUN8I_H3) += pinctrl-sun8i-h3.o > diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c > new file mode 100644 > index 000000000000..d38d8770c9da > --- /dev/null > +++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c > @@ -0,0 +1,105 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (c) 2020 Frank Lee <frank@allwinner.com> > + * > + * Based on: > + * huangshuosheng <huangshuosheng@allwinnertech.com> > + */ > + > +#include <linux/module.h> > +#include <linux/platform_device.h> > +#include <linux/of.h> > +#include <linux/of_device.h> > +#include <linux/pinctrl/pinctrl.h> > +#include "pinctrl-sunxi.h" > + > +static const struct sunxi_desc_pin a100_r_pins[] = { > + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 0), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "s_i2c0"), /* SCK */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 1), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "s_i2c0"), /* SDA */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 2), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "s_uart0"), /* TX */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 3), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "s_uart0"), /* RX */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 4), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "s_jtag"), /* MS */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 5), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "s_jtag"), /* CK */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 6), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "s_jtag"), /* DO */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 7), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "s_jtag"), /* DI */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 8), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "s_i2c1"), /* SCK */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 9), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "s_i2c1"), /* SDA */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 10), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "s_pwm"), > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 11), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "s_cpu"), /* CUR_W */ > + SUNXI_FUNCTION(0x3, "s_cir"), /* IN */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)), > +}; > + > +static const struct sunxi_pinctrl_desc a100_r_pinctrl_data = { > + .pins = a100_r_pins, > + .npins = ARRAY_SIZE(a100_r_pins), > + .pin_base = PL_BASE, > + .irq_banks = 1, > +}; > + > +static int a100_r_pinctrl_probe(struct platform_device *pdev) > +{ > + return sunxi_pinctrl_init(pdev, &a100_r_pinctrl_data); > +} > + > +static const struct of_device_id a100_r_pinctrl_match[] = { > + { .compatible = "allwinner,sun50i-a100-r-pinctrl", }, > + {} > +}; > +MODULE_DEVICE_TABLE(of, a100_r_pinctrl_match); > + > +static struct platform_driver a100_r_pinctrl_driver = { > + .probe = a100_r_pinctrl_probe, > + .driver = { > + .name = "sun50iw10p1-r-pinctrl", > + .of_match_table = a100_r_pinctrl_match, > + }, > +}; > +module_platform_driver(a100_r_pinctrl_driver); > diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c > new file mode 100644 > index 000000000000..b9591009f0a4 > --- /dev/null > +++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c > @@ -0,0 +1,710 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (c) 2020 Frank Lee <frank@allwinner.com> > + * > + * Based on: > + * huangshuosheng <huangshuosheng@allwinnertech.com> > + */ > + > +#include <linux/module.h> > +#include <linux/platform_device.h> > +#include <linux/of.h> > +#include <linux/of_device.h> > +#include <linux/pinctrl/pinctrl.h> > + > +#include "pinctrl-sunxi.h" > + > +static const struct sunxi_desc_pin a100_pins[] = { > + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 0), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "uart2"), /* TX */ > + SUNXI_FUNCTION(0x3, "spi2"), /* CS */ > + SUNXI_FUNCTION(0x4, "jtag"), /* MS */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 1), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "uart2"), /* RX */ > + SUNXI_FUNCTION(0x3, "spi2"), /* CLK */ > + SUNXI_FUNCTION(0x4, "jtag"), /* CK */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 2), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "uart2"), /* RTS */ > + SUNXI_FUNCTION(0x3, "spi2"), /* MOSI */ > + SUNXI_FUNCTION(0x4, "jtag"), /* DO */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 3), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "uart2"), /* CTS */ > + SUNXI_FUNCTION(0x3, "spi2"), /* MISO */ > + SUNXI_FUNCTION(0x4, "jtag"), /* DI */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 4), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "i2c1"), /* SCK */ > + SUNXI_FUNCTION(0x3, "i2s0"), /* MCLK */ > + SUNXI_FUNCTION(0x4, "jtag"), /* MS_GPU */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 5), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "i2c1"), /* SDA */ > + SUNXI_FUNCTION(0x3, "i2s0"), /* BCLK */ > + SUNXI_FUNCTION(0x4, "jtag"), /* CK_GPU */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 6), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x3, "i2s0"), /* LRCK */ > + SUNXI_FUNCTION(0x4, "jtag"), /* DO_GPU */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 7), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "spdif"), /* DIN */ > + SUNXI_FUNCTION(0x3, "i2s0"), /* DOUT0 */ > + SUNXI_FUNCTION(0x4, "i2s0"), /* DIN1 */ I guess the second one would be i2s1? > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 8), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "spdif"), /* DOUT */ > + SUNXI_FUNCTION(0x3, "i2s0"), /* DIN0 */ > + SUNXI_FUNCTION(0x4, "i2s0"), /* DOUT1 */ Ditto > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 9), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "uart0"), /* TX */ > + SUNXI_FUNCTION(0x3, "i2c0"), /* SCK */ > + SUNXI_FUNCTION(0x4, "jtag"), /* DI_GPU */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 10), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "uart0"), /* RX */ > + SUNXI_FUNCTION(0x3, "i2c0"), /* SDA */ > + SUNXI_FUNCTION(0x4, "pwm1"), > + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)), > + /* HOLE */ > + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "nand0"), /* WE */ > + SUNXI_FUNCTION(0x3, "mmc2"), /* DS */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 0)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "nand0"), /* ALE */ > + SUNXI_FUNCTION(0x3, "mmc2"), /* RST */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 1)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "nand0"), /* CLE */ > + SUNXI_FUNCTION(0x4, "spi0"), /* MOSI */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 2)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "nand0"), /* CE1 */ > + SUNXI_FUNCTION(0x4, "spi0"), /* CS0 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 3)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "nand0"), /* CE0 */ > + SUNXI_FUNCTION(0x4, "spi0"), /* MISO */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 4)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "nand0"), /* RE */ > + SUNXI_FUNCTION(0x3, "mmc2"), /* CLK */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 5)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "nand0"), /* RB0 */ > + SUNXI_FUNCTION(0x3, "mmc2"), /* CMD */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 6)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "nand0"), /* RB1 */ > + SUNXI_FUNCTION(0x4, "spi0"), /* CS1 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 7)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "nand0"), /* DQ7 */ > + SUNXI_FUNCTION(0x3, "mmc2"), /* D3 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 8)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "nand0"), /* DQ6 */ > + SUNXI_FUNCTION(0x3, "mmc2"), /* D4 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 9)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "nand0"), /* DQ5 */ > + SUNXI_FUNCTION(0x3, "mmc2"), /* D0 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 10)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "nand0"), /* DQ4 */ > + SUNXI_FUNCTION(0x3, "mmc2"), /* D5 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 11)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "nand0"), /* DQS */ > + SUNXI_FUNCTION(0x4, "spi0"), /* CLK */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 12)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "nand0"), /* DQ3 */ > + SUNXI_FUNCTION(0x3, "mmc2"), /* D1 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 13)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "nand0"), /* DQ2 */ > + SUNXI_FUNCTION(0x3, "mmc2"), /* D6 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 14)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "nand0"), /* DQ1 */ > + SUNXI_FUNCTION(0x3, "mmc2"), /* D2 */ > + SUNXI_FUNCTION(0x4, "spi0"), /* WP */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 15)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "nand0"), /* DQ0 */ > + SUNXI_FUNCTION(0x3, "mmc2"), /* D7 */ > + SUNXI_FUNCTION(0x4, "spi0"), /* HOLD */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 16)), > + /* HOLE */ > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* D2 */ > + SUNXI_FUNCTION(0x3, "lvds0"), /* D0P */ > + SUNXI_FUNCTION(0x4, "dsi0"), /* DP0 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 0)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* D3 */ > + SUNXI_FUNCTION(0x3, "lvds0"), /* D0N */ > + SUNXI_FUNCTION(0x4, "dsi0"), /* DM0 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 1)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* D4 */ > + SUNXI_FUNCTION(0x3, "lvds0"), /* D1P */ > + SUNXI_FUNCTION(0x4, "dsi0"), /* DP1 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 2)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* D5 */ > + SUNXI_FUNCTION(0x3, "lvds0"), /* D1N */ > + SUNXI_FUNCTION(0x4, "dsi0"), /* DM1 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 3)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* D6 */ > + SUNXI_FUNCTION(0x3, "lvds0"), /* D2P */ > + SUNXI_FUNCTION(0x4, "dsi0"), /* CKP */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 4)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* D7 */ > + SUNXI_FUNCTION(0x3, "lvds0"), /* D2N */ > + SUNXI_FUNCTION(0x4, "dsi0"), /* CKM */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 5)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* D10 */ > + SUNXI_FUNCTION(0x3, "lvds0"), /* CKP */ > + SUNXI_FUNCTION(0x4, "dsi0"), /* DP2 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 6)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* D11 */ > + SUNXI_FUNCTION(0x3, "lvds0"), /* CKN */ > + SUNXI_FUNCTION(0x4, "dsi0"), /* DM2 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 7)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* D12 */ > + SUNXI_FUNCTION(0x4, "dsi0"), /* DP3 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 8)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* D13 */ > + SUNXI_FUNCTION(0x4, "dsi0"), /* DM3 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 9)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* D14 */ > + SUNXI_FUNCTION(0x4, "spi1"), /* CS */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 10)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* D15 */ > + SUNXI_FUNCTION(0x4, "spi1"), /* CLK */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 11)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* D18 */ > + SUNXI_FUNCTION(0x4, "spi1"), /* MOSI */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 12)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* D19 */ > + SUNXI_FUNCTION(0x4, "spi1"), /* MISO */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 13)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* D20 */ > + SUNXI_FUNCTION(0x4, "uart3"), /* TX */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 14)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* D21 */ > + SUNXI_FUNCTION(0x4, "uart3"), /* RX */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 15)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* D22 */ > + SUNXI_FUNCTION(0x4, "uart3"), /* RTS */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 16)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* D23 */ > + SUNXI_FUNCTION(0x4, "uart3"), /* CTS */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 17)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 18), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* CLK */ > + SUNXI_FUNCTION(0x4, "uart4"), /* TX */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 18)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 19), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* DE */ > + SUNXI_FUNCTION(0x4, "uart4"), /* RX */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 19)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 20), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* HSYNC */ > + SUNXI_FUNCTION(0x3, "pwm2"), > + SUNXI_FUNCTION(0x4, "uart4"), /* RTS */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 20)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 21), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "lcd0"), /* VSYNC */ > + SUNXI_FUNCTION(0x3, "pwm3"), > + SUNXI_FUNCTION(0x4, "uart4"), /* CTS */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 21)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 22), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "pwm1"), > + SUNXI_FUNCTION(0x4, "i2c0"), /* SCK */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 22)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 23), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "pwm0"), > + SUNXI_FUNCTION(0x4, "i2c0"), /* SDA */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 23)), > + /* HOLE */ > + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "csi"), /* MCLK */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 0)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "i2c2"), /* SCK */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 1)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "i2c2"), /* SDA */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 2)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "i2c3"), /* SCK */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 3)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "i2c3"), /* SDA */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 4)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "csi"), /* MCLK */ > + SUNXI_FUNCTION(0x3, "pll"), /* LOCK_DBG */ > + SUNXI_FUNCTION(0x4, "i2s2"), /* MCLK */ > + SUNXI_FUNCTION(0x5, "ledc"), /* LEDC */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 5)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x3, "bist0"), /* RESULT0 */ > + SUNXI_FUNCTION(0x4, "i2s2"), /* BCLK */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 6)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "csi"), /* SM_VS */ > + SUNXI_FUNCTION(0x3, "bist0"), /* RESULT1 */ > + SUNXI_FUNCTION(0x4, "i2s2"), /* LRCK */ > + SUNXI_FUNCTION(0x5, "tcon0"), /* TRIG */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 7)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x3, "bist0"), /* RESULT2 */ > + SUNXI_FUNCTION(0x4, "i2s2"), /* DOUT0 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 8)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x3, "bist0"), /* RESULT3 */ > + SUNXI_FUNCTION(0x4, "i2s2"), /* DIN0 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 9)), > + /* HOLE */ > + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "mmc0"), /* D1 */ > + SUNXI_FUNCTION(0x3, "jtag"), /* MS1 */ > + SUNXI_FUNCTION(0x4, "jtag"), /* MS_GPU */ We should use another name here, since the code will just pick the first one and ignore the second. What about jtag-gpu? > + SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 0)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "mmc0"), /* D0 */ > + SUNXI_FUNCTION(0x3, "jtag"), /* DI1 */ > + SUNXI_FUNCTION(0x4, "jtag"), /* DI_GPU */ Ditto > + SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 1)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "mmc0"), /* CLK */ > + SUNXI_FUNCTION(0x3, "uart0"), /* TX */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 2)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "mmc0"), /* CMD */ > + SUNXI_FUNCTION(0x3, "jtag"), /* DO */ > + SUNXI_FUNCTION(0x4, "jtag"), /* DO_GPU */ Ditto > + SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 3)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "mmc0"), /* D3 */ > + SUNXI_FUNCTION(0x3, "uart0"), /* RX */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 4)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "mmc0"), /* D2 */ > + SUNXI_FUNCTION(0x3, "jtag"), /* CK */ > + SUNXI_FUNCTION(0x4, "jtag"), /* CK_GPU */ Ditto > + SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 5)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 6)), > + /* HOLE */ > + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "mmc1"), /* CLK */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 0)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "mmc1"), /* CMD */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 1)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "mmc1"), /* D0 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 2)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "mmc1"), /* D1 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 3)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "mmc1"), /* D2 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 4)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "mmc1"), /* D3 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 5)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "uart1"), /* TX */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 6)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "uart1"), /* RX */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 7)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "uart1"), /* RTS */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 8)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "uart1"), /* CTS */ > + SUNXI_FUNCTION(0x3, "i2s1"), /* MCLK */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 9)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x3, "i2s1"), /* BCLK */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 10)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x3, "i2s1"), /* LRCK */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 11)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x3, "i2s1"), /* DOUT0 */ > + SUNXI_FUNCTION(0x4, "i2s1"), /* DIN1 */ This is suspicious too > + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 12)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x3, "i2s1"), /* DIN0 */ > + SUNXI_FUNCTION(0x4, "i2s1"), /* DOUT1 */ Here too > + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 13)), > + /* HOLE */ > + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 0), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "i2c0"), /* SCK */ > + SUNXI_FUNCTION(0x5, "emac0"), /* RXD1 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 0)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 1), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "i2c0"), /* SDA */ > + SUNXI_FUNCTION(0x5, "emac0"), /* RXD0 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 1)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 2), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "i2c1"), /* SCK */ > + SUNXI_FUNCTION(0x3, "cpu"), /* CUR_W */ What is "cpu" supposed to be? > + SUNXI_FUNCTION(0x5, "emac0"), /* RXCTL */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 2)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 3), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "i2c1"), /* SDA */ > + SUNXI_FUNCTION(0x3, "cir0"), /* OUT */ > + SUNXI_FUNCTION(0x5, "emac0"), /* CLKIN */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 3)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 4), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "uart3"), /* TX */ > + SUNXI_FUNCTION(0x3, "spi1"), /* CS */ > + SUNXI_FUNCTION(0x4, "cpu"), /* CUR_W */ > + SUNXI_FUNCTION(0x5, "emac0"), /* TXD1 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 4)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 5), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "uart3"), /* RX */ > + SUNXI_FUNCTION(0x3, "spi1"), /* CLK */ > + SUNXI_FUNCTION(0x4, "ledc"), > + SUNXI_FUNCTION(0x5, "emac0"), /* TXD0 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 5)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 6), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "uart3"), /* RTS */ > + SUNXI_FUNCTION(0x3, "spi1"), /* MOSI */ > + SUNXI_FUNCTION(0x5, "emac0"), /* TXCK */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 6)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 7), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "uart3"), /* CTS */ > + SUNXI_FUNCTION(0x3, "spi1"), /* MISO */ > + SUNXI_FUNCTION(0x4, "spdif"), /* OUT */ > + SUNXI_FUNCTION(0x5, "emac0"), /* TXCTL */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 7)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 8), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "dmic"), /* CLK */ > + SUNXI_FUNCTION(0x3, "spi2"), /* CS */ > + SUNXI_FUNCTION(0x4, "i2s2"), /* MCLK */ > + SUNXI_FUNCTION(0x5, "i2s2"), /* DIN2 */ Same issue than previously > + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 8)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 9), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "dmic"), /* DATA0 */ > + SUNXI_FUNCTION(0x3, "spi2"), /* CLK */ > + SUNXI_FUNCTION(0x4, "i2s2"), /* BCLK */ > + SUNXI_FUNCTION(0x5, "emac0"), /* MDC */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 9)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 10), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "dmic"), /* DATA1 */ > + SUNXI_FUNCTION(0x3, "spi2"), /* MOSI */ > + SUNXI_FUNCTION(0x4, "i2s2"), /* LRCK */ > + SUNXI_FUNCTION(0x5, "emac0"), /* MDIO */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 10)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 11), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "dmic"), /* DATA2 */ > + SUNXI_FUNCTION(0x3, "spi2"), /* MISO */ > + SUNXI_FUNCTION(0x4, "i2s2"), /* DOUT0 */ > + SUNXI_FUNCTION(0x5, "i2s2"), /* DIN1 */ Here as well > + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 11)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 12), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "dmic"), /* DATA3 */ > + SUNXI_FUNCTION(0x3, "i2c3"), /* SCK */ > + SUNXI_FUNCTION(0x4, "i2s2"), /* DIN0 */ > + SUNXI_FUNCTION(0x5, "i2s2"), /* DOUT1 */ Ditto > + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 12)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 13), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x3, "i2c3"), /* SCK */ > + SUNXI_FUNCTION(0x4, "i2s3"), /* MCLK */ > + SUNXI_FUNCTION(0x5, "emac0"), /* EPHY */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 13)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 14), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x4, "i2s3"), /* BCLK */ > + SUNXI_FUNCTION(0x5, "emac0"), /* RXD3 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 14)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 15), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x4, "i2s3"), /* LRCK */ > + SUNXI_FUNCTION(0x5, "emac0"), /* RXD2 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 15)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 16), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x3, "i2s3"), /* DOUT0 */ > + SUNXI_FUNCTION(0x4, "i2s3"), /* DIN1 */ Ditto > + SUNXI_FUNCTION(0x5, "emac0"), /* RXCK */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 16)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 17), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x3, "i2s3"), /* DOUT1 */ > + SUNXI_FUNCTION(0x4, "i2s3"), /* DIN0 */ Ditto > + SUNXI_FUNCTION(0x5, "emac0"), /* TXD3 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 17)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 18), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "cir0"), /* OUT */ > + SUNXI_FUNCTION(0x3, "i2s3"), /* DOUT2 */ > + SUNXI_FUNCTION(0x4, "i2s3"), /* DIN2 */ Ditto > + SUNXI_FUNCTION(0x5, "emac0"), /* TXD2 */ > + SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 18)), > + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 19), > + SUNXI_FUNCTION(0x0, "gpio_in"), > + SUNXI_FUNCTION(0x1, "gpio_out"), > + SUNXI_FUNCTION(0x2, "cir0"), /* IN */ > + SUNXI_FUNCTION(0x3, "i2s3"), /* DOUT3 */ > + SUNXI_FUNCTION(0x4, "i2s3"), /* DIN3 */ Ditto Maxime [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 228 bytes --] ^ permalink raw reply [flat|nested] 15+ messages in thread
* 回复：[PATCH 2/4] pinctrl: sunxi: add support for the Allwinner A100 pin controller 2020-05-22 15:28 ` Maxime Ripard @ 2020-06-03 9:44 ` 李扬韬 2020-06-05 15:13 ` Maxime Ripard 0 siblings, 1 reply; 15+ messages in thread From: 李扬韬 @ 2020-06-03 9:44 UTC (permalink / raw) To: Maxime Ripard Cc: wens, robh+dt, mturquette, sboyd, linus.walleij, p.zabel, 黄烁生, tiny.windzz, linux-arm-kernel, devicetree, linux-kernel, linux-clk, linux-gpio >> + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0), >> + SUNXI_FUNCTION(0x0, "gpio_in"), >> + SUNXI_FUNCTION(0x1, "gpio_out"), >> + SUNXI_FUNCTION(0x2, "mmc0"), /* D1 */ >> + SUNXI_FUNCTION(0x3, "jtag"), /* MS1 */ >> + SUNXI_FUNCTION(0x4, "jtag"), /* MS_GPU */ > >We should use another name here, since the code will just pick the first one and >ignore the second. What about jtag-gpu? The underscores are used in front, so changing it to jtag_gpu may be more consistent. >> + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 7), >> + SUNXI_FUNCTION(0x0, "gpio_in"), >> + SUNXI_FUNCTION(0x1, "gpio_out"), >> + SUNXI_FUNCTION(0x2, "spdif"), /* DIN */ >> + SUNXI_FUNCTION(0x3, "i2s0"), /* DOUT0 */ >> + SUNXI_FUNCTION(0x4, "i2s0"), /* DIN1 */ > >I guess the second one would be i2s1? No, each i2s may have many inputs and outputs. SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 19), SUNXI_FUNCTION(0x0, "gpio_in"), SUNXI_FUNCTION(0x1, "gpio_out"), SUNXI_FUNCTION(0x2, "cir0"), /* IN */ SUNXI_FUNCTION(0x3, "i2s3_dout3"), /* DOUT3 */ SUNXI_FUNCTION(0x4, "i2s3_din3"), /* DIN3 */ SUNXI_FUNCTION(0x5, "ledc"), SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 19)), Considering that the same pin has multiple same functions, so add a suffix, like i2s3_dout3 and i2s3_din3? Or specify muxsel in the device tree may be another solution. >> + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 2), >> + SUNXI_FUNCTION(0x0, "gpio_in"), >> + SUNXI_FUNCTION(0x1, "gpio_out"), >> + SUNXI_FUNCTION(0x2, "i2c1"), /* SCK */ >> + SUNXI_FUNCTION(0x3, "cpu"), /* CUR_W */ > >What is "cpu" supposed to be? As far as I know, this is a function that has never been used. The hardware guy said that it can be used to control the CPU to reduce the current. Thx, Yangtao ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: 回复：[PATCH 2/4] pinctrl: sunxi: add support for the Allwinner A100 pin controller 2020-06-03 9:44 ` 回复：[PATCH " 李扬韬 @ 2020-06-05 15:13 ` Maxime Ripard 2020-06-16 9:26 ` Frank Lee 0 siblings, 1 reply; 15+ messages in thread From: Maxime Ripard @ 2020-06-05 15:13 UTC (permalink / raw) To: wens, 李扬韬, linus.walleij Cc: robh+dt, mturquette, sboyd, p.zabel, 黄烁生, tiny.windzz, linux-arm-kernel, devicetree, linux-kernel, linux-clk, linux-gpio [-- Attachment #1: Type: text/plain, Size: 2618 bytes --] Hi Frank, On Wed, Jun 03, 2020 at 05:44:36PM +0800, 李扬韬 wrote: > >> + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0), > >> + SUNXI_FUNCTION(0x0, "gpio_in"), > >> + SUNXI_FUNCTION(0x1, "gpio_out"), > >> + SUNXI_FUNCTION(0x2, "mmc0"), /* D1 */ > >> + SUNXI_FUNCTION(0x3, "jtag"), /* MS1 */ > >> + SUNXI_FUNCTION(0x4, "jtag"), /* MS_GPU */ > > > >We should use another name here, since the code will just pick the first one and > >ignore the second. What about jtag-gpu? > > The underscores are used in front, so changing it to jtag_gpu may be more consistent. Yep, that makes sense > >> + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 7), > >> + SUNXI_FUNCTION(0x0, "gpio_in"), > >> + SUNXI_FUNCTION(0x1, "gpio_out"), > >> + SUNXI_FUNCTION(0x2, "spdif"), /* DIN */ > >> + SUNXI_FUNCTION(0x3, "i2s0"), /* DOUT0 */ > >> + SUNXI_FUNCTION(0x4, "i2s0"), /* DIN1 */ > > > >I guess the second one would be i2s1? > > No, each i2s may have many inputs and outputs. > > SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 19), > SUNXI_FUNCTION(0x0, "gpio_in"), > SUNXI_FUNCTION(0x1, "gpio_out"), > SUNXI_FUNCTION(0x2, "cir0"), /* IN */ > SUNXI_FUNCTION(0x3, "i2s3_dout3"), /* DOUT3 */ > SUNXI_FUNCTION(0x4, "i2s3_din3"), /* DIN3 */ > SUNXI_FUNCTION(0x5, "ledc"), > SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 19)), > > Considering that the same pin has multiple same functions, > so add a suffix, like i2s3_dout3 and i2s3_din3? > > Or specify muxsel in the device tree may be another solution. Having muxsel is not really an option. We have two sets of bindings to maintain already, adding a third one would make it fairly hard to maintain. And the second binding we support is the generic pinctrl binding, so I'm not really sure why we would want to move away from that. And I'm not really fond of having a suffix either. It kind of breaks the consistency we had so far, and ideally I'd like to keep that. Chen-Yu, Linus? Any input on that one? > >> + SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 2), > >> + SUNXI_FUNCTION(0x0, "gpio_in"), > >> + SUNXI_FUNCTION(0x1, "gpio_out"), > >> + SUNXI_FUNCTION(0x2, "i2c1"), /* SCK */ > >> + SUNXI_FUNCTION(0x3, "cpu"), /* CUR_W */ > > > >What is "cpu" supposed to be? > > As far as I know, this is a function that has never been used. > The hardware guy said that it can be used to control the CPU to reduce the current. Ok. Do we really need to add it right now if we don't really know what it's going to be used for? Thanks! Maxime [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 228 bytes --] ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: 回复：[PATCH 2/4] pinctrl: sunxi: add support for the Allwinner A100 pin controller 2020-06-05 15:13 ` Maxime Ripard @ 2020-06-16 9:26 ` Frank Lee 2020-06-20 21:27 ` Linus Walleij 0 siblings, 1 reply; 15+ messages in thread From: Frank Lee @ 2020-06-16 9:26 UTC (permalink / raw) To: Maxime Ripard Cc: wens, 李扬韬, linus.walleij, robh+dt, mturquette, sboyd, p.zabel, 黄烁生, linux-arm-kernel, devicetree, linux-kernel, linux-clk, linux-gpio HI Chen-Yu, Linus, On Fri, Jun 5, 2020 at 11:13 PM Maxime Ripard <maxime@cerno.tech> wrote: > > Hi Frank, > > On Wed, Jun 03, 2020 at 05:44:36PM +0800, 李扬韬 wrote: > > >> + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0), > > >> + SUNXI_FUNCTION(0x0, "gpio_in"), > > >> + SUNXI_FUNCTION(0x1, "gpio_out"), > > >> + SUNXI_FUNCTION(0x2, "mmc0"), /* D1 */ > > >> + SUNXI_FUNCTION(0x3, "jtag"), /* MS1 */ > > >> + SUNXI_FUNCTION(0x4, "jtag"), /* MS_GPU */ > > > > > >We should use another name here, since the code will just pick the first one and > > >ignore the second. What about jtag-gpu? > > > > The underscores are used in front, so changing it to jtag_gpu may be more consistent. > > Yep, that makes sense > > > >> + SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 7), > > >> + SUNXI_FUNCTION(0x0, "gpio_in"), > > >> + SUNXI_FUNCTION(0x1, "gpio_out"), > > >> + SUNXI_FUNCTION(0x2, "spdif"), /* DIN */ > > >> + SUNXI_FUNCTION(0x3, "i2s0"), /* DOUT0 */ > > >> + SUNXI_FUNCTION(0x4, "i2s0"), /* DIN1 */ > > > > > >I guess the second one would be i2s1? > > > > No, each i2s may have many inputs and outputs. > > > > SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 19), > > SUNXI_FUNCTION(0x0, "gpio_in"), > > SUNXI_FUNCTION(0x1, "gpio_out"), > > SUNXI_FUNCTION(0x2, "cir0"), /* IN */ > > SUNXI_FUNCTION(0x3, "i2s3_dout3"), /* DOUT3 */ > > SUNXI_FUNCTION(0x4, "i2s3_din3"), /* DIN3 */ > > SUNXI_FUNCTION(0x5, "ledc"), > > SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 19)), > > > > Considering that the same pin has multiple same functions, > > so add a suffix, like i2s3_dout3 and i2s3_din3? > > > > Or specify muxsel in the device tree may be another solution. > > Having muxsel is not really an option. We have two sets of bindings to > maintain already, adding a third one would make it fairly hard to > maintain. And the second binding we support is the generic pinctrl > binding, so I'm not really sure why we would want to move away from > that. > > And I'm not really fond of having a suffix either. It kind of breaks the > consistency we had so far, and ideally I'd like to keep that. > > Chen-Yu, Linus? Any input on that one? PING...... ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: 回复：[PATCH 2/4] pinctrl: sunxi: add support for the Allwinner A100 pin controller 2020-06-16 9:26 ` Frank Lee @ 2020-06-20 21:27 ` Linus Walleij 0 siblings, 0 replies; 15+ messages in thread From: Linus Walleij @ 2020-06-20 21:27 UTC (permalink / raw) To: Frank Lee Cc: Maxime Ripard, wens, 李扬韬, robh+dt, mturquette, sboyd, p.zabel, 黄烁生, linux-arm-kernel, devicetree, linux-kernel, linux-clk, linux-gpio On Tue, Jun 16, 2020 at 11:27 AM Frank Lee <tiny.windzz@gmail.com> wrote: > HI Chen-Yu, Linus, > On Fri, Jun 5, 2020 at 11:13 PM Maxime Ripard <maxime@cerno.tech> wrote: > > > Considering that the same pin has multiple same functions, > > > so add a suffix, like i2s3_dout3 and i2s3_din3? > > > > > > Or specify muxsel in the device tree may be another solution. > > > > Having muxsel is not really an option. We have two sets of bindings to > > maintain already, adding a third one would make it fairly hard to > > maintain. And the second binding we support is the generic pinctrl > > binding, so I'm not really sure why we would want to move away from > > that. > > > > And I'm not really fond of having a suffix either. It kind of breaks the > > consistency we had so far, and ideally I'd like to keep that. > > > > Chen-Yu, Linus? Any input on that one? This is entirely up to the driver maintainer. They need to keep the code together and the naming consistent with how they perceive the hardware works and/or is intended to work. Yours, Linus Walleij ^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 3/4] arm64: allwinner: A100: add the basical Allwinner A100 DTSI file 2020-05-22 3:07 [PATCH 0/4] Allwinner A100 Initial support Frank Lee 2020-05-22 3:07 ` [PATCH 1/4] clk: sunxi-ng: add support for the Allwinner A100 CCU Frank Lee 2020-05-22 3:07 ` [PATCH 2/4] pinctrl: sunxi: add support for the Allwinner A100 pin controller Frank Lee @ 2020-05-22 3:07 ` Frank Lee 2020-05-22 3:07 ` [PATCH 4/4] arm64: allwinner: A100: add support for Allwinner Perf1 board Frank Lee 2020-05-22 15:02 ` [PATCH 0/4] Allwinner A100 Initial support Maxime Ripard 4 siblings, 0 replies; 15+ messages in thread From: Frank Lee @ 2020-05-22 3:07 UTC (permalink / raw) To: mripard, wens, robh+dt, mturquette, sboyd, linus.walleij, p.zabel, frank, huangshuosheng, tiny.windzz Cc: linux-arm-kernel, devicetree, linux-kernel, linux-clk, linux-gpio Allwinner A100 is a new SoC with Cortex-A53 cores, this commit adds the basical DTSI file of it, including the clock, pins and UART support. Signed-off-by: Frank Lee <frank@allwinnertech.com> --- .../arm64/boot/dts/allwinner/sun50i-a100.dtsi | 173 ++++++++++++++++++ 1 file changed, 173 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi new file mode 100644 index 000000000000..bd9bf9b2f832 --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi @@ -0,0 +1,173 @@ +// SPDX-License-Identifier: (GPL-2.0+ or MIT) +/* + * Copyright (c) 2020 Frank Lee <frank@allwinner.com> + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/sun50i-a100-ccu.h> +#include <dt-bindings/clock/sun50i-a100-r-ccu.h> +#include <dt-bindings/reset/sun50i-a100-ccu.h> +#include <dt-bindings/reset/sun50i-a100-r-ccu.h> + +/ { + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + compatible = "arm,armv8"; + device_type = "cpu"; + reg = <0x0>; + enable-method = "psci"; + }; + + cpu@1 { + compatible = "arm,armv8"; + device_type = "cpu"; + reg = <0x1>; + enable-method = "psci"; + }; + + cpu@2 { + compatible = "arm,armv8"; + device_type = "cpu"; + reg = <0x2>; + enable-method = "psci"; + }; + + cpu@3 { + compatible = "arm,armv8"; + device_type = "cpu"; + reg = <0x3>; + enable-method = "psci"; + }; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + iosc: internal-osc-clk { + compatible = "fixed-clock"; + clock-frequency = <16000000>; + clock-accuracy = <300000000>; + clock-output-names = "iosc"; + #clock-cells = <0>; + }; + + dcxo24M: dcxo24M_clk { + compatible = "fixed-clock"; + clock-frequency = <24000000>; + clock-output-names = "dcxo24M"; + #clock-cells = <0>; + }; + + osc32k: osc32k_clk { + compatible = "fixed-clock"; + clock-frequency = <32768>; + clock-output-names = "osc32k"; + #clock-cells = <0>; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, + <GIC_PPI 14 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, + <GIC_PPI 11 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, + <GIC_PPI 10 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + }; + + soc: soc { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + ccu: clock@3001000 { + compatible = "allwinner,sun50i-a100-ccu"; + reg = <0x0 0x03001000 0x0 0x1000>; + clocks = <&dcxo24M>, <&osc32k>, <&iosc>; + clock-names = "hosc", "losc", "iosc"; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + gic: interrupt-controller@3021000 { + compatible = "arm,gic-400"; + reg = <0x0 0x03021000 0x0 0x1000>, + <0x0 0x03022000 0x0 0x2000>, + <0x0 0x03024000 0x0 0x2000>, + <0x0 0x03026000 0x0 0x2000>; + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_HIGH)>; + interrupt-controller; + #interrupt-cells = <3>; + }; + + pio: pinctrl@300b000 { + compatible = "allwinner,sun50i-a100-pinctrl"; + reg = <0x0 0x0300b000 0x0 0x400>; + interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_APB1>, <&dcxo24M>, <&osc32k>; + clock-names = "apb", "hosc", "losc"; + gpio-controller; + #gpio-cells = <3>; + interrupt-controller; + #interrupt-cells = <3>; + + uart0_pb_pins: uart0-pb-pins { + pins = "PB9", "PB10"; + function = "uart0"; + }; + }; + + uart0: serial@5000000 { + compatible = "snps,dw-apb-uart"; + reg = <0x0 0x05000000 0x0 0x400>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART0>; + resets = <&ccu RST_BUS_UART0>; + }; + + r_ccu: clock@7010000 { + compatible = "allwinner,sun50i-a100-r-ccu"; + reg = <0x0 0x07010000 0x0 0x400>; + clocks = <&dcxo24M>, <&osc32k>, <&iosc>, + <&ccu CLK_PLL_PERIPH0>; + clock-names = "hosc", "losc", "iosc", "pll-periph"; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + r_pio: pinctrl@7022000 { + compatible = "allwinner,sun50i-a100-r-pinctrl"; + reg = <0x0 0x07022000 0x0 0x400>; + interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&r_ccu CLK_R_APB1>, <&dcxo24M>, <&osc32k>; + clock-names = "apb", "hosc", "losc"; + gpio-controller; + #gpio-cells = <3>; + interrupt-controller; + #interrupt-cells = <3>; + }; + }; +}; -- 2.24.0 ^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 4/4] arm64: allwinner: A100: add support for Allwinner Perf1 board 2020-05-22 3:07 [PATCH 0/4] Allwinner A100 Initial support Frank Lee ` (2 preceding siblings ...) 2020-05-22 3:07 ` [PATCH 3/4] arm64: allwinner: A100: add the basical Allwinner A100 DTSI file Frank Lee @ 2020-05-22 3:07 ` Frank Lee 2020-05-22 15:31 ` Maxime Ripard 2020-05-22 15:02 ` [PATCH 0/4] Allwinner A100 Initial support Maxime Ripard 4 siblings, 1 reply; 15+ messages in thread From: Frank Lee @ 2020-05-22 3:07 UTC (permalink / raw) To: mripard, wens, robh+dt, mturquette, sboyd, linus.walleij, p.zabel, frank, huangshuosheng, tiny.windzz Cc: linux-arm-kernel, devicetree, linux-kernel, linux-clk, linux-gpio A100 perf1 is an Allwinner A100-based SBC, with the following features: - 1GiB DDR3 DRAM - AXP803 PMIC - 2 USB 2.0 ports - MicroSD slot and on-board eMMC module - on-board Nand flash - ··· Adds initial support for it, including the UART. Signed-off-by: Frank Lee <frank@allwinnertech.com> --- arch/arm64/boot/dts/allwinner/Makefile | 1 + .../allwinner/sun50i-a100-allwinner-perf1.dts | 27 +++++++++++++++++++ 2 files changed, 28 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a100-allwinner-perf1.dts diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile index e4d3cd0ac5bb..ab780dbdd17b 100644 --- a/arch/arm64/boot/dts/allwinner/Makefile +++ b/arch/arm64/boot/dts/allwinner/Makefile @@ -14,6 +14,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.1.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a100-allwinner-perf1.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus-v1.2.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-emlid-neutis-n5-devboard.dtb diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a100-allwinner-perf1.dts b/arch/arm64/boot/dts/allwinner/sun50i-a100-allwinner-perf1.dts new file mode 100644 index 000000000000..32c9986920ed --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-a100-allwinner-perf1.dts @@ -0,0 +1,27 @@ +// SPDX-License-Identifier: (GPL-2.0+ or MIT) +/* + * Copyright (c) 2020 Frank Lee <frank@allwinner.com> + */ + +/dts-v1/; + +#include "sun50i-a100.dtsi" + +/{ + model = "A100 perf1"; + compatible = "allwinner,a100-perf1", "allwinner,sun50i-a100"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pb_pins>; + status = "okay"; +}; -- 2.24.0 ^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: [PATCH 4/4] arm64: allwinner: A100: add support for Allwinner Perf1 board 2020-05-22 3:07 ` [PATCH 4/4] arm64: allwinner: A100: add support for Allwinner Perf1 board Frank Lee @ 2020-05-22 15:31 ` Maxime Ripard 0 siblings, 0 replies; 15+ messages in thread From: Maxime Ripard @ 2020-05-22 15:31 UTC (permalink / raw) To: Frank Lee Cc: wens, robh+dt, mturquette, sboyd, linus.walleij, p.zabel, huangshuosheng, tiny.windzz, linux-arm-kernel, devicetree, linux-kernel, linux-clk, linux-gpio [-- Attachment #1: Type: text/plain, Size: 2286 bytes --] Hi, On Fri, May 22, 2020 at 11:07:43AM +0800, Frank Lee wrote: > A100 perf1 is an Allwinner A100-based SBC, with the following features: > > - 1GiB DDR3 DRAM > - AXP803 PMIC > - 2 USB 2.0 ports > - MicroSD slot and on-board eMMC module > - on-board Nand flash > - ··· > > Adds initial support for it, including the UART. > > Signed-off-by: Frank Lee <frank@allwinnertech.com> Which bootloader have you used to test this? > --- > arch/arm64/boot/dts/allwinner/Makefile | 1 + > .../allwinner/sun50i-a100-allwinner-perf1.dts | 27 +++++++++++++++++++ > 2 files changed, 28 insertions(+) > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a100-allwinner-perf1.dts > > diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile > index e4d3cd0ac5bb..ab780dbdd17b 100644 > --- a/arch/arm64/boot/dts/allwinner/Makefile > +++ b/arch/arm64/boot/dts/allwinner/Makefile > @@ -14,6 +14,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.1.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a100-allwinner-perf1.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus-v1.2.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-emlid-neutis-n5-devboard.dtb > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a100-allwinner-perf1.dts b/arch/arm64/boot/dts/allwinner/sun50i-a100-allwinner-perf1.dts > new file mode 100644 > index 000000000000..32c9986920ed > --- /dev/null > +++ b/arch/arm64/boot/dts/allwinner/sun50i-a100-allwinner-perf1.dts > @@ -0,0 +1,27 @@ > +// SPDX-License-Identifier: (GPL-2.0+ or MIT) > +/* > + * Copyright (c) 2020 Frank Lee <frank@allwinner.com> > + */ > + > +/dts-v1/; > + > +#include "sun50i-a100.dtsi" > + > +/{ > + model = "A100 perf1"; Having the same casing and the "brand" would be great here, so something like "Allwinner A100 Perf1", or just Perf1 if that name is only ever going to be used on the A100 > + compatible = "allwinner,a100-perf1", "allwinner,sun50i-a100"; This binding needs to be documented Maxime [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 228 bytes --] ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH 0/4] Allwinner A100 Initial support 2020-05-22 3:07 [PATCH 0/4] Allwinner A100 Initial support Frank Lee ` (3 preceding siblings ...) 2020-05-22 3:07 ` [PATCH 4/4] arm64: allwinner: A100: add support for Allwinner Perf1 board Frank Lee @ 2020-05-22 15:02 ` Maxime Ripard 4 siblings, 0 replies; 15+ messages in thread From: Maxime Ripard @ 2020-05-22 15:02 UTC (permalink / raw) To: Frank Lee Cc: wens, robh+dt, mturquette, sboyd, linus.walleij, p.zabel, huangshuosheng, tiny.windzz, linux-arm-kernel, devicetree, linux-kernel, linux-clk, linux-gpio [-- Attachment #1: Type: text/plain, Size: 433 bytes --] Hi, On Fri, May 22, 2020 at 11:07:39AM +0800, Frank Lee wrote: > This patch set adds initial support for allwinner a100 soc, > which is a 64-bit tablet chip. The patches are mostly good for a first iteration, thanks! Could you provide a bit more context on what that SoC is and if the user manual is available somewhere? It will be pretty hard to review without it. Also, is that perf1 board available somewhere? Thanks! Maxime [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 228 bytes --] ^ permalink raw reply [flat|nested] 15+ messages in thread
end of thread, other threads:[~2020-06-20 21:28 UTC | newest] Thread overview: 15+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2020-05-22 3:07 [PATCH 0/4] Allwinner A100 Initial support Frank Lee 2020-05-22 3:07 ` [PATCH 1/4] clk: sunxi-ng: add support for the Allwinner A100 CCU Frank Lee 2020-05-22 15:14 ` Maxime Ripard 2020-06-03 9:42 ` 回复：[PATCH " 李扬韬 2020-06-03 9:48 ` [PATCH " Chen-Yu Tsai 2020-05-22 3:07 ` [PATCH 2/4] pinctrl: sunxi: add support for the Allwinner A100 pin controller Frank Lee 2020-05-22 15:28 ` Maxime Ripard 2020-06-03 9:44 ` 回复：[PATCH " 李扬韬 2020-06-05 15:13 ` Maxime Ripard 2020-06-16 9:26 ` Frank Lee 2020-06-20 21:27 ` Linus Walleij 2020-05-22 3:07 ` [PATCH 3/4] arm64: allwinner: A100: add the basical Allwinner A100 DTSI file Frank Lee 2020-05-22 3:07 ` [PATCH 4/4] arm64: allwinner: A100: add support for Allwinner Perf1 board Frank Lee 2020-05-22 15:31 ` Maxime Ripard 2020-05-22 15:02 ` [PATCH 0/4] Allwinner A100 Initial support Maxime Ripard
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).