* [PATCH V3 0/5] Add minimal boot support for IPQ6018
@ 2020-01-03 11:49 Sricharan R
2020-01-03 11:49 ` [PATCH V3 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings Sricharan R
` (4 more replies)
0 siblings, 5 replies; 12+ messages in thread
From: Sricharan R @ 2020-01-03 11:49 UTC (permalink / raw)
To: sricharan, agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-clk, linux-gpio, linux-kernel, linux-soc,
robh+dt, sboyd, sivaprak
The IPQ6018 is Qualcomm\u2019s 802.11ax SoC for Routers,
Gateways and Access Points.
This series adds minimal board boot support for ipq6018-cp01 board.
[V3]
* Removed clock driver and bindings from this patch series, and added them
as a different series.
* Removed qpic_padN from pinctrl driver.
* Addressed review comments in dts, and added the remaining fixed clocks their
* Fixed review comments in pinctrl bindings
* Patch 4 arm64: dts: Add ipq6018 SoC and CP01 board support has build
dependency with,
https://patchwork.ozlabs.org/patch/1217293/
[v2]
* Splitted dt bindings and driver into different patches. Added missing bindings
and some style changes.
* Added ipq6018 schema
* Addressed review comments for gcc clock bindings.
* Removed all clk critical flags, removed 1/1 factor clocks, moved to new
way of specifying clk parents, and addressed other review comments.
* Sorted nodes based on address, name, label. Removed unused clock nodes,
Addressed other review comments.
Sricharan R (5):
dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings
pinctrl: qcom: Add ipq6018 pinctrl driver
dt-bindings: qcom: Add ipq6018 bindings
arm64: dts: Add ipq6018 SoC and CP01 board support
arm64: defconfig: Enable qcom ipq6018 clock and pinctrl
Documentation/devicetree/bindings/arm/qcom.yaml | 8 +
.../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml | 174 +++
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts | 30 +
arch/arm64/boot/dts/qcom/ipq6018.dtsi | 263 +++++
arch/arm64/configs/defconfig | 3 +
drivers/pinctrl/qcom/Kconfig | 10 +
drivers/pinctrl/qcom/Makefile | 1 +
drivers/pinctrl/qcom/pinctrl-ipq6018.c | 1107 ++++++++++++++++++++
9 files changed, 1597 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
create mode 100644 arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
create mode 100644 arch/arm64/boot/dts/qcom/ipq6018.dtsi
create mode 100644 drivers/pinctrl/qcom/pinctrl-ipq6018.c
--
1.9.1
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH V3 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings
2020-01-03 11:49 [PATCH V3 0/5] Add minimal boot support for IPQ6018 Sricharan R
@ 2020-01-03 11:49 ` Sricharan R
2020-01-04 0:58 ` Rob Herring
2020-01-07 11:55 ` Linus Walleij
2020-01-03 11:49 ` [PATCH V3 2/5] pinctrl: qcom: Add ipq6018 pinctrl driver Sricharan R
` (3 subsequent siblings)
4 siblings, 2 replies; 12+ messages in thread
From: Sricharan R @ 2020-01-03 11:49 UTC (permalink / raw)
To: sricharan, agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-clk, linux-gpio, linux-kernel, linux-soc,
robh+dt, sboyd, sivaprak
Add device tree binding Documentation details for ipq6018
pinctrl driver.
Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
---
[v3] Fixed the example dt node, inherited properties
.../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml | 166 +++++++++++++++++++++
1 file changed, 166 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
new file mode 100644
index 0000000..e959c5f
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
@@ -0,0 +1,166 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,ipq6018-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies, Inc. IPQ6018 TLMM block
+
+maintainers:
+ - Sricharan R <sricharan@codeaurora.org>
+
+description: |
+ This binding describes the Top Level Mode Multiplexer block found in the
+ IPQ6018 platform.
+
+properties:
+ compatible:
+ const: qcom,ipq6018-pinctrl
+ reg:
+ maxItems: 1
+ interrupts:
+ Description: Specifies the TLMM summary IRQ
+ maxItems: 1
+ interrupt-controller: true
+ '#interrupt-cells':
+ Description:
+ Specifies the PIN numbers and Flags, as defined in defined in
+ include/dt-bindings/interrupt-controller/irq.h
+ const: 2
+ gpio-controller: true
+ '#gpio-cells':
+ Description: Specifying the pin number and flags, as defined in
+ include/dt-bindings/gpio/gpio.h
+ const: 2
+ gpio-ranges:
+ Description: Documentation/devicetree/bindings/gpio/gpio.txt
+ maxItems: 1
+
+#PIN CONFIGURATION NODES
+patternProperties:
+ '-pins$':
+ type: object
+ Description:
+ Pinctrl node's client devices use subnodes for desired pin configuration.
+ Client device subnodes use below standard properties.
+
+ Properties:
+ pins:
+ allOf:
+ $ref: /schemas/types.yaml#/definitions/string
+ enum:
+ gpio0-gpio80
+ sdc1_clk
+ sdc1_cmd
+ sdc1_data
+ sdc2_clk
+ sdc2_cmd
+ sdc2_data
+ qdsd_cmd
+ qdsd_data0
+ qdsd_data1
+ qdsd_data2
+ qdsd_data3
+ Description:
+ List of gpio pins affected by the properties specified in this
+ subnode.
+
+ function:
+ allOf:
+ $ref: /schemas/types.yaml#/definitions/string
+ enum:
+ adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char,
+ atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac,
+ atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0,
+ atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp_i2c1,
+ blsp_i2c2, blsp_i2c3, blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_spi1,
+ blsp_spi1_cs1, blsp_spi1_cs2, blsp_spi1_cs3, blsp_spi2,
+ blsp_spi2_cs1, blsp_spi2_cs2, blsp_spi2_cs3, blsp_spi3,
+ blsp_spi3_cs1, blsp_spi3_cs2, blsp_spi3_cs3, blsp_spi4, blsp_spi5,
+ blsp_spi6, blsp_uart1, blsp_uart2, blsp_uim1, blsp_uim2, cam1_rst,
+ cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0,
+ cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v,
+ dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass,
+ flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a,
+ gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0,
+ gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2,
+ ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc,
+ nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s,
+ pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
+ pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a,
+ pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1,
+ qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0,
+ qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1,
+ qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b,
+ qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write,
+ sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3,
+ uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst
+ Description:
+ Specify the alternative function to be configured for the specified
+ pins.
+ bias-disable:
+ allOf:
+ $ref: /schemas/pinctrl/pincfg-node.yaml
+ Description:
+ The specified pins should be configured as no pull.
+ bias-pull-down:
+ allOf:
+ $ref: /schemas/pinctrl/pincfg-node.yaml
+ Description:
+ The specified pins should be configured as pull down.
+ bias-pull-up:
+ allOf:
+ $ref: /schemas/pinctrl/pincfg-node.yaml
+ Description:
+ The specified pins should be configured as pull up.
+ output-high:
+ allOf:
+ $ref: /schemas/pinctrl/pincfg-node.yaml
+ Description:
+ The specified pins are configured in output mode, driven high.
+ This option is not available for sdc pins.
+ output-low:
+ allOf:
+ $ref: /schemas/pinctrl/pincfg-node.yaml
+ Description:
+ The specified pins are configured in output mode, driven low.
+ This option is not available for sdc pins.
+ drive-strength:
+ allOf:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [2, 4, 6, 8, 10, 12, 14, 16]
+ Description:
+ Selects the drive strength for the specified pins, in mA.
+
+ required:
+ - pins
+ - function
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - interrupt-controller
+ - '#interrupt-cells'
+ - gpio-controller
+ - '#gpio-cells'
+ - gpio-ranges
+
+example:
+ tlmm: pinctrl@1000000 {
+ compatible = "qcom,ipq6018-pinctrl";
+ reg = <0x01000000 0x300000>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&tlmm 0 80>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ serial_3_pins: serial3-pinmux {
+ pins = "gpio44", "gpio45";
+ function = "blsp2_uart";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+ };
--
1.9.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH V3 2/5] pinctrl: qcom: Add ipq6018 pinctrl driver
2020-01-03 11:49 [PATCH V3 0/5] Add minimal boot support for IPQ6018 Sricharan R
2020-01-03 11:49 ` [PATCH V3 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings Sricharan R
@ 2020-01-03 11:49 ` Sricharan R
2020-01-04 1:33 ` Bjorn Andersson
2020-01-03 11:49 ` [PATCH V3 3/5] dt-bindings: qcom: Add ipq6018 bindings Sricharan R
` (2 subsequent siblings)
4 siblings, 1 reply; 12+ messages in thread
From: Sricharan R @ 2020-01-03 11:49 UTC (permalink / raw)
To: sricharan, agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-clk, linux-gpio, linux-kernel, linux-soc,
robh+dt, sboyd, sivaprak
Add initial pinctrl driver to support pin configuration with
pinctrl framework for ipq6018.
Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
---
[v3] Removed qpic_padN
drivers/pinctrl/qcom/Kconfig | 10 +
drivers/pinctrl/qcom/Makefile | 1 +
drivers/pinctrl/qcom/pinctrl-ipq6018.c | 1107 ++++++++++++++++++++++++++++++++
3 files changed, 1118 insertions(+)
create mode 100644 drivers/pinctrl/qcom/pinctrl-ipq6018.c
diff --git a/drivers/pinctrl/qcom/Kconfig b/drivers/pinctrl/qcom/Kconfig
index 811af2f8..c5d4428 100644
--- a/drivers/pinctrl/qcom/Kconfig
+++ b/drivers/pinctrl/qcom/Kconfig
@@ -50,6 +50,16 @@ config PINCTRL_IPQ8074
Qualcomm Technologies Inc. IPQ8074 platform. Select this for
IPQ8074.
+config PINCTRL_IPQ6018
+ tristate "Qualcomm Technologies, Inc. IPQ6018 pin controller driver"
+ depends on GPIOLIB && OF
+ select PINCTRL_MSM
+ help
+ This is the pinctrl, pinmux, pinconf and gpiolib driver for
+ the Qualcomm Technologies Inc. TLMM block found on the
+ Qualcomm Technologies Inc. IPQ6018 platform. Select this for
+ IPQ6018.
+
config PINCTRL_MSM8660
tristate "Qualcomm 8660 pin controller driver"
depends on GPIOLIB && OF
diff --git a/drivers/pinctrl/qcom/Makefile b/drivers/pinctrl/qcom/Makefile
index c2c2f9a..d9e0904 100644
--- a/drivers/pinctrl/qcom/Makefile
+++ b/drivers/pinctrl/qcom/Makefile
@@ -6,6 +6,7 @@ obj-$(CONFIG_PINCTRL_APQ8084) += pinctrl-apq8084.o
obj-$(CONFIG_PINCTRL_IPQ4019) += pinctrl-ipq4019.o
obj-$(CONFIG_PINCTRL_IPQ8064) += pinctrl-ipq8064.o
obj-$(CONFIG_PINCTRL_IPQ8074) += pinctrl-ipq8074.o
+obj-$(CONFIG_PINCTRL_IPQ6018) += pinctrl-ipq6018.o
obj-$(CONFIG_PINCTRL_MSM8660) += pinctrl-msm8660.o
obj-$(CONFIG_PINCTRL_MSM8960) += pinctrl-msm8960.o
obj-$(CONFIG_PINCTRL_MSM8X74) += pinctrl-msm8x74.o
diff --git a/drivers/pinctrl/qcom/pinctrl-ipq6018.c b/drivers/pinctrl/qcom/pinctrl-ipq6018.c
new file mode 100644
index 0000000..38c33a7
--- /dev/null
+++ b/drivers/pinctrl/qcom/pinctrl-ipq6018.c
@@ -0,0 +1,1107 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2016-2018, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-msm.h"
+
+#define FUNCTION(fname) \
+ [msm_mux_##fname] = { \
+ .name = #fname, \
+ .groups = fname##_groups, \
+ .ngroups = ARRAY_SIZE(fname##_groups), \
+ }
+
+#define REG_SIZE 0x1000
+#define PINGROUP(id, f1, f2, f3, f4, f5, f6, f7, f8, f9) \
+ { \
+ .name = "gpio" #id, \
+ .pins = gpio##id##_pins, \
+ .npins = (unsigned int)ARRAY_SIZE(gpio##id##_pins), \
+ .funcs = (int[]){ \
+ msm_mux_gpio, /* gpio mode */ \
+ msm_mux_##f1, \
+ msm_mux_##f2, \
+ msm_mux_##f3, \
+ msm_mux_##f4, \
+ msm_mux_##f5, \
+ msm_mux_##f6, \
+ msm_mux_##f7, \
+ msm_mux_##f8, \
+ msm_mux_##f9 \
+ }, \
+ .nfuncs = 10, \
+ .ctl_reg = REG_SIZE * id, \
+ .io_reg = 0x4 + REG_SIZE * id, \
+ .intr_cfg_reg = 0x8 + REG_SIZE * id, \
+ .intr_status_reg = 0xc + REG_SIZE * id, \
+ .intr_target_reg = 0x8 + REG_SIZE * id, \
+ .mux_bit = 2, \
+ .pull_bit = 0, \
+ .drv_bit = 6, \
+ .oe_bit = 9, \
+ .in_bit = 0, \
+ .out_bit = 1, \
+ .intr_enable_bit = 0, \
+ .intr_status_bit = 0, \
+ .intr_target_bit = 5, \
+ .intr_target_kpss_val = 3, \
+ .intr_raw_status_bit = 4, \
+ .intr_polarity_bit = 1, \
+ .intr_detection_bit = 2, \
+ .intr_detection_width = 2, \
+ }
+
+static const struct pinctrl_pin_desc ipq6018_pins[] = {
+ PINCTRL_PIN(0, "GPIO_0"),
+ PINCTRL_PIN(1, "GPIO_1"),
+ PINCTRL_PIN(2, "GPIO_2"),
+ PINCTRL_PIN(3, "GPIO_3"),
+ PINCTRL_PIN(4, "GPIO_4"),
+ PINCTRL_PIN(5, "GPIO_5"),
+ PINCTRL_PIN(6, "GPIO_6"),
+ PINCTRL_PIN(7, "GPIO_7"),
+ PINCTRL_PIN(8, "GPIO_8"),
+ PINCTRL_PIN(9, "GPIO_9"),
+ PINCTRL_PIN(10, "GPIO_10"),
+ PINCTRL_PIN(11, "GPIO_11"),
+ PINCTRL_PIN(12, "GPIO_12"),
+ PINCTRL_PIN(13, "GPIO_13"),
+ PINCTRL_PIN(14, "GPIO_14"),
+ PINCTRL_PIN(15, "GPIO_15"),
+ PINCTRL_PIN(16, "GPIO_16"),
+ PINCTRL_PIN(17, "GPIO_17"),
+ PINCTRL_PIN(18, "GPIO_18"),
+ PINCTRL_PIN(19, "GPIO_19"),
+ PINCTRL_PIN(20, "GPIO_20"),
+ PINCTRL_PIN(21, "GPIO_21"),
+ PINCTRL_PIN(22, "GPIO_22"),
+ PINCTRL_PIN(23, "GPIO_23"),
+ PINCTRL_PIN(24, "GPIO_24"),
+ PINCTRL_PIN(25, "GPIO_25"),
+ PINCTRL_PIN(26, "GPIO_26"),
+ PINCTRL_PIN(27, "GPIO_27"),
+ PINCTRL_PIN(28, "GPIO_28"),
+ PINCTRL_PIN(29, "GPIO_29"),
+ PINCTRL_PIN(30, "GPIO_30"),
+ PINCTRL_PIN(31, "GPIO_31"),
+ PINCTRL_PIN(32, "GPIO_32"),
+ PINCTRL_PIN(33, "GPIO_33"),
+ PINCTRL_PIN(34, "GPIO_34"),
+ PINCTRL_PIN(35, "GPIO_35"),
+ PINCTRL_PIN(36, "GPIO_36"),
+ PINCTRL_PIN(37, "GPIO_37"),
+ PINCTRL_PIN(38, "GPIO_38"),
+ PINCTRL_PIN(39, "GPIO_39"),
+ PINCTRL_PIN(40, "GPIO_40"),
+ PINCTRL_PIN(41, "GPIO_41"),
+ PINCTRL_PIN(42, "GPIO_42"),
+ PINCTRL_PIN(43, "GPIO_43"),
+ PINCTRL_PIN(44, "GPIO_44"),
+ PINCTRL_PIN(45, "GPIO_45"),
+ PINCTRL_PIN(46, "GPIO_46"),
+ PINCTRL_PIN(47, "GPIO_47"),
+ PINCTRL_PIN(48, "GPIO_48"),
+ PINCTRL_PIN(49, "GPIO_49"),
+ PINCTRL_PIN(50, "GPIO_50"),
+ PINCTRL_PIN(51, "GPIO_51"),
+ PINCTRL_PIN(52, "GPIO_52"),
+ PINCTRL_PIN(53, "GPIO_53"),
+ PINCTRL_PIN(54, "GPIO_54"),
+ PINCTRL_PIN(55, "GPIO_55"),
+ PINCTRL_PIN(56, "GPIO_56"),
+ PINCTRL_PIN(57, "GPIO_57"),
+ PINCTRL_PIN(58, "GPIO_58"),
+ PINCTRL_PIN(59, "GPIO_59"),
+ PINCTRL_PIN(60, "GPIO_60"),
+ PINCTRL_PIN(61, "GPIO_61"),
+ PINCTRL_PIN(62, "GPIO_62"),
+ PINCTRL_PIN(63, "GPIO_63"),
+ PINCTRL_PIN(64, "GPIO_64"),
+ PINCTRL_PIN(65, "GPIO_65"),
+ PINCTRL_PIN(66, "GPIO_66"),
+ PINCTRL_PIN(67, "GPIO_67"),
+ PINCTRL_PIN(68, "GPIO_68"),
+ PINCTRL_PIN(69, "GPIO_69"),
+ PINCTRL_PIN(70, "GPIO_70"),
+ PINCTRL_PIN(71, "GPIO_71"),
+ PINCTRL_PIN(72, "GPIO_72"),
+ PINCTRL_PIN(73, "GPIO_73"),
+ PINCTRL_PIN(74, "GPIO_74"),
+ PINCTRL_PIN(75, "GPIO_75"),
+ PINCTRL_PIN(76, "GPIO_76"),
+ PINCTRL_PIN(77, "GPIO_77"),
+ PINCTRL_PIN(78, "GPIO_78"),
+ PINCTRL_PIN(79, "GPIO_79"),
+};
+
+#define DECLARE_MSM_GPIO_PINS(pin) \
+ static const unsigned int gpio##pin##_pins[] = { pin }
+DECLARE_MSM_GPIO_PINS(0);
+DECLARE_MSM_GPIO_PINS(1);
+DECLARE_MSM_GPIO_PINS(2);
+DECLARE_MSM_GPIO_PINS(3);
+DECLARE_MSM_GPIO_PINS(4);
+DECLARE_MSM_GPIO_PINS(5);
+DECLARE_MSM_GPIO_PINS(6);
+DECLARE_MSM_GPIO_PINS(7);
+DECLARE_MSM_GPIO_PINS(8);
+DECLARE_MSM_GPIO_PINS(9);
+DECLARE_MSM_GPIO_PINS(10);
+DECLARE_MSM_GPIO_PINS(11);
+DECLARE_MSM_GPIO_PINS(12);
+DECLARE_MSM_GPIO_PINS(13);
+DECLARE_MSM_GPIO_PINS(14);
+DECLARE_MSM_GPIO_PINS(15);
+DECLARE_MSM_GPIO_PINS(16);
+DECLARE_MSM_GPIO_PINS(17);
+DECLARE_MSM_GPIO_PINS(18);
+DECLARE_MSM_GPIO_PINS(19);
+DECLARE_MSM_GPIO_PINS(20);
+DECLARE_MSM_GPIO_PINS(21);
+DECLARE_MSM_GPIO_PINS(22);
+DECLARE_MSM_GPIO_PINS(23);
+DECLARE_MSM_GPIO_PINS(24);
+DECLARE_MSM_GPIO_PINS(25);
+DECLARE_MSM_GPIO_PINS(26);
+DECLARE_MSM_GPIO_PINS(27);
+DECLARE_MSM_GPIO_PINS(28);
+DECLARE_MSM_GPIO_PINS(29);
+DECLARE_MSM_GPIO_PINS(30);
+DECLARE_MSM_GPIO_PINS(31);
+DECLARE_MSM_GPIO_PINS(32);
+DECLARE_MSM_GPIO_PINS(33);
+DECLARE_MSM_GPIO_PINS(34);
+DECLARE_MSM_GPIO_PINS(35);
+DECLARE_MSM_GPIO_PINS(36);
+DECLARE_MSM_GPIO_PINS(37);
+DECLARE_MSM_GPIO_PINS(38);
+DECLARE_MSM_GPIO_PINS(39);
+DECLARE_MSM_GPIO_PINS(40);
+DECLARE_MSM_GPIO_PINS(41);
+DECLARE_MSM_GPIO_PINS(42);
+DECLARE_MSM_GPIO_PINS(43);
+DECLARE_MSM_GPIO_PINS(44);
+DECLARE_MSM_GPIO_PINS(45);
+DECLARE_MSM_GPIO_PINS(46);
+DECLARE_MSM_GPIO_PINS(47);
+DECLARE_MSM_GPIO_PINS(48);
+DECLARE_MSM_GPIO_PINS(49);
+DECLARE_MSM_GPIO_PINS(50);
+DECLARE_MSM_GPIO_PINS(51);
+DECLARE_MSM_GPIO_PINS(52);
+DECLARE_MSM_GPIO_PINS(53);
+DECLARE_MSM_GPIO_PINS(54);
+DECLARE_MSM_GPIO_PINS(55);
+DECLARE_MSM_GPIO_PINS(56);
+DECLARE_MSM_GPIO_PINS(57);
+DECLARE_MSM_GPIO_PINS(58);
+DECLARE_MSM_GPIO_PINS(59);
+DECLARE_MSM_GPIO_PINS(60);
+DECLARE_MSM_GPIO_PINS(61);
+DECLARE_MSM_GPIO_PINS(62);
+DECLARE_MSM_GPIO_PINS(63);
+DECLARE_MSM_GPIO_PINS(64);
+DECLARE_MSM_GPIO_PINS(65);
+DECLARE_MSM_GPIO_PINS(66);
+DECLARE_MSM_GPIO_PINS(67);
+DECLARE_MSM_GPIO_PINS(68);
+DECLARE_MSM_GPIO_PINS(69);
+DECLARE_MSM_GPIO_PINS(70);
+DECLARE_MSM_GPIO_PINS(71);
+DECLARE_MSM_GPIO_PINS(72);
+DECLARE_MSM_GPIO_PINS(73);
+DECLARE_MSM_GPIO_PINS(74);
+DECLARE_MSM_GPIO_PINS(75);
+DECLARE_MSM_GPIO_PINS(76);
+DECLARE_MSM_GPIO_PINS(77);
+DECLARE_MSM_GPIO_PINS(78);
+DECLARE_MSM_GPIO_PINS(79);
+
+enum ipq6018_functions {
+ msm_mux_atest_char,
+ msm_mux_atest_char0,
+ msm_mux_atest_char1,
+ msm_mux_atest_char2,
+ msm_mux_atest_char3,
+ msm_mux_audio0,
+ msm_mux_audio1,
+ msm_mux_audio2,
+ msm_mux_audio3,
+ msm_mux_audio_rxbclk,
+ msm_mux_audio_rxfsync,
+ msm_mux_audio_rxmclk,
+ msm_mux_audio_rxmclkin,
+ msm_mux_audio_txbclk,
+ msm_mux_audio_txfsync,
+ msm_mux_audio_txmclk,
+ msm_mux_audio_txmclkin,
+ msm_mux_blsp0_i2c,
+ msm_mux_blsp0_spi,
+ msm_mux_blsp0_uart,
+ msm_mux_blsp1_i2c,
+ msm_mux_blsp1_spi,
+ msm_mux_blsp1_uart,
+ msm_mux_blsp2_i2c,
+ msm_mux_blsp2_spi,
+ msm_mux_blsp2_uart,
+ msm_mux_blsp3_i2c,
+ msm_mux_blsp3_spi,
+ msm_mux_blsp3_uart,
+ msm_mux_blsp4_i2c,
+ msm_mux_blsp4_spi,
+ msm_mux_blsp4_uart,
+ msm_mux_blsp5_i2c,
+ msm_mux_blsp5_uart,
+ msm_mux_burn0,
+ msm_mux_burn1,
+ msm_mux_cri_trng,
+ msm_mux_cri_trng0,
+ msm_mux_cri_trng1,
+ msm_mux_cxc0,
+ msm_mux_cxc1,
+ msm_mux_dbg_out,
+ msm_mux_gcc_plltest,
+ msm_mux_gcc_tlmm,
+ msm_mux_gpio,
+ msm_mux_lpass_aud,
+ msm_mux_lpass_aud0,
+ msm_mux_lpass_aud1,
+ msm_mux_lpass_aud2,
+ msm_mux_lpass_pcm,
+ msm_mux_lpass_pdm,
+ msm_mux_mac00,
+ msm_mux_mac01,
+ msm_mux_mac10,
+ msm_mux_mac11,
+ msm_mux_mac12,
+ msm_mux_mac13,
+ msm_mux_mac20,
+ msm_mux_mac21,
+ msm_mux_mdc,
+ msm_mux_mdio,
+ msm_mux_pcie0_clk,
+ msm_mux_pcie0_rst,
+ msm_mux_pcie0_wake,
+ msm_mux_prng_rosc,
+ msm_mux_pta1_0,
+ msm_mux_pta1_1,
+ msm_mux_pta1_2,
+ msm_mux_pta2_0,
+ msm_mux_pta2_1,
+ msm_mux_pta2_2,
+ msm_mux_pwm00,
+ msm_mux_pwm01,
+ msm_mux_pwm02,
+ msm_mux_pwm03,
+ msm_mux_pwm04,
+ msm_mux_pwm10,
+ msm_mux_pwm11,
+ msm_mux_pwm12,
+ msm_mux_pwm13,
+ msm_mux_pwm14,
+ msm_mux_pwm20,
+ msm_mux_pwm21,
+ msm_mux_pwm22,
+ msm_mux_pwm23,
+ msm_mux_pwm24,
+ msm_mux_pwm30,
+ msm_mux_pwm31,
+ msm_mux_pwm32,
+ msm_mux_pwm33,
+ msm_mux_qdss_cti_trig_in_a0,
+ msm_mux_qdss_cti_trig_in_a1,
+ msm_mux_qdss_cti_trig_out_a0,
+ msm_mux_qdss_cti_trig_out_a1,
+ msm_mux_qdss_cti_trig_in_b0,
+ msm_mux_qdss_cti_trig_in_b1,
+ msm_mux_qdss_cti_trig_out_b0,
+ msm_mux_qdss_cti_trig_out_b1,
+ msm_mux_qdss_traceclk_a,
+ msm_mux_qdss_tracectl_a,
+ msm_mux_qdss_tracedata_a,
+ msm_mux_qdss_traceclk_b,
+ msm_mux_qdss_tracectl_b,
+ msm_mux_qdss_tracedata_b,
+ msm_mux_qpic_pad,
+ msm_mux_rx0,
+ msm_mux_rx1,
+ msm_mux_rx_swrm,
+ msm_mux_rx_swrm0,
+ msm_mux_rx_swrm1,
+ msm_mux_sd_card,
+ msm_mux_sd_write,
+ msm_mux_tsens_max,
+ msm_mux_tx_swrm,
+ msm_mux_tx_swrm0,
+ msm_mux_tx_swrm1,
+ msm_mux_tx_swrm2,
+ msm_mux_wci20,
+ msm_mux_wci21,
+ msm_mux_wci22,
+ msm_mux_wci23,
+ msm_mux_wsa_swrm,
+ msm_mux__,
+};
+
+static const char * const blsp3_uart_groups[] = {
+ "gpio73", "gpio74", "gpio75", "gpio76",
+};
+
+static const char * const blsp3_i2c_groups[] = {
+ "gpio73", "gpio74",
+};
+
+static const char * const blsp3_spi_groups[] = {
+ "gpio73", "gpio74", "gpio75", "gpio76", "gpio77", "gpio78", "gpio79",
+};
+
+static const char * const wci20_groups[] = {
+ "gpio0", "gpio2",
+};
+
+static const char * const qpic_pad_groups[] = {
+ "gpio0", "gpio1", "gpio2", "gpio3", "gpio4", "gpio9", "gpio10",
+ "gpio11", "gpio17",
+};
+
+static const char * const burn0_groups[] = {
+ "gpio0",
+};
+
+static const char * const mac12_groups[] = {
+ "gpio1", "gpio11",
+};
+
+static const char * const qdss_tracectl_b_groups[] = {
+ "gpio1",
+};
+
+static const char * const burn1_groups[] = {
+ "gpio1",
+};
+
+static const char * const qdss_traceclk_b_groups[] = {
+ "gpio0",
+};
+
+static const char * const qdss_tracedata_b_groups[] = {
+ "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7", "gpio8", "gpio9",
+ "gpio10", "gpio11", "gpio12", "gpio13", "gpio14", "gpio15", "gpio16",
+ "gpio17",
+};
+
+static const char * const mac01_groups[] = {
+ "gpio3", "gpio4",
+};
+
+static const char * const mac21_groups[] = {
+ "gpio5", "gpio6",
+};
+
+static const char * const atest_char_groups[] = {
+ "gpio9",
+};
+
+static const char * const cxc0_groups[] = {
+ "gpio9", "gpio16",
+};
+
+static const char * const mac13_groups[] = {
+ "gpio9", "gpio16",
+};
+
+static const char * const dbg_out_groups[] = {
+ "gpio9",
+};
+
+static const char * const wci22_groups[] = {
+ "gpio11", "gpio17",
+};
+
+static const char * const pwm00_groups[] = {
+ "gpio18",
+};
+
+static const char * const atest_char0_groups[] = {
+ "gpio18",
+};
+
+static const char * const wci23_groups[] = {
+ "gpio18", "gpio19",
+};
+
+static const char * const mac11_groups[] = {
+ "gpio18", "gpio19",
+};
+
+static const char * const pwm10_groups[] = {
+ "gpio19",
+};
+
+static const char * const atest_char1_groups[] = {
+ "gpio19",
+};
+
+static const char * const pwm20_groups[] = {
+ "gpio20",
+};
+
+static const char * const atest_char2_groups[] = {
+ "gpio20",
+};
+
+static const char * const pwm30_groups[] = {
+ "gpio21",
+};
+
+static const char * const atest_char3_groups[] = {
+ "gpio21",
+};
+
+static const char * const audio_txmclk_groups[] = {
+ "gpio22",
+};
+
+static const char * const audio_txmclkin_groups[] = {
+ "gpio22",
+};
+
+static const char * const pwm02_groups[] = {
+ "gpio22",
+};
+
+static const char * const tx_swrm0_groups[] = {
+ "gpio22",
+};
+
+static const char * const qdss_cti_trig_out_b0_groups[] = {
+ "gpio22",
+};
+
+static const char * const audio_txbclk_groups[] = {
+ "gpio23",
+};
+
+static const char * const pwm12_groups[] = {
+ "gpio23",
+};
+
+static const char * const wsa_swrm_groups[] = {
+ "gpio23", "gpio24",
+};
+
+static const char * const tx_swrm1_groups[] = {
+ "gpio23",
+};
+
+static const char * const qdss_cti_trig_in_b0_groups[] = {
+ "gpio23",
+};
+
+static const char * const audio_txfsync_groups[] = {
+ "gpio24",
+};
+
+static const char * const pwm22_groups[] = {
+ "gpio24",
+};
+
+static const char * const tx_swrm2_groups[] = {
+ "gpio24",
+};
+
+static const char * const qdss_cti_trig_out_b1_groups[] = {
+ "gpio24",
+};
+
+static const char * const audio0_groups[] = {
+ "gpio25", "gpio32",
+};
+
+static const char * const pwm32_groups[] = {
+ "gpio25",
+};
+
+static const char * const tx_swrm_groups[] = {
+ "gpio25",
+};
+
+static const char * const qdss_cti_trig_in_b1_groups[] = {
+ "gpio25",
+};
+
+static const char * const audio1_groups[] = {
+ "gpio26", "gpio33",
+};
+
+static const char * const pwm04_groups[] = {
+ "gpio26",
+};
+
+static const char * const audio2_groups[] = {
+ "gpio27",
+};
+
+static const char * const pwm14_groups[] = {
+ "gpio27",
+};
+
+static const char * const audio3_groups[] = {
+ "gpio28",
+};
+
+static const char * const pwm24_groups[] = {
+ "gpio28",
+};
+
+static const char * const audio_rxmclk_groups[] = {
+ "gpio29",
+};
+
+static const char * const audio_rxmclkin_groups[] = {
+ "gpio29",
+};
+
+static const char * const pwm03_groups[] = {
+ "gpio29",
+};
+
+static const char * const lpass_pdm_groups[] = {
+ "gpio29", "gpio30", "gpio31", "gpio32",
+};
+
+static const char * const lpass_aud_groups[] = {
+ "gpio29",
+};
+
+static const char * const qdss_cti_trig_in_a1_groups[] = {
+ "gpio29",
+};
+
+static const char * const audio_rxbclk_groups[] = {
+ "gpio30",
+};
+
+static const char * const pwm13_groups[] = {
+ "gpio30",
+};
+
+static const char * const lpass_aud0_groups[] = {
+ "gpio30",
+};
+
+static const char * const rx_swrm_groups[] = {
+ "gpio30",
+};
+
+static const char * const qdss_cti_trig_out_a1_groups[] = {
+ "gpio30",
+};
+
+static const char * const audio_rxfsync_groups[] = {
+ "gpio31",
+};
+
+static const char * const pwm23_groups[] = {
+ "gpio31",
+};
+
+static const char * const lpass_aud1_groups[] = {
+ "gpio31",
+};
+
+static const char * const rx_swrm0_groups[] = {
+ "gpio31",
+};
+
+static const char * const qdss_cti_trig_in_a0_groups[] = {
+ "gpio31",
+};
+
+static const char * const pwm33_groups[] = {
+ "gpio32",
+};
+
+static const char * const lpass_aud2_groups[] = {
+ "gpio32",
+};
+
+static const char * const rx_swrm1_groups[] = {
+ "gpio32",
+};
+
+static const char * const qdss_cti_trig_out_a0_groups[] = {
+ "gpio32",
+};
+
+static const char * const lpass_pcm_groups[] = {
+ "gpio34", "gpio35", "gpio36", "gpio37",
+};
+
+static const char * const mac10_groups[] = {
+ "gpio34", "gpio35",
+};
+
+static const char * const mac00_groups[] = {
+ "gpio34", "gpio35",
+};
+
+static const char * const mac20_groups[] = {
+ "gpio36", "gpio37",
+};
+
+static const char * const blsp0_uart_groups[] = {
+ "gpio38", "gpio39", "gpio40", "gpio41",
+};
+
+static const char * const blsp0_i2c_groups[] = {
+ "gpio38", "gpio39",
+};
+
+static const char * const blsp0_spi_groups[] = {
+ "gpio38", "gpio39", "gpio40", "gpio41",
+};
+
+static const char * const blsp2_uart_groups[] = {
+ "gpio42", "gpio43", "gpio44", "gpio45",
+};
+
+static const char * const blsp2_i2c_groups[] = {
+ "gpio42", "gpio43",
+};
+
+static const char * const blsp2_spi_groups[] = {
+ "gpio42", "gpio43", "gpio44", "gpio45",
+};
+
+static const char * const blsp5_i2c_groups[] = {
+ "gpio46", "gpio47",
+};
+
+static const char * const blsp5_uart_groups[] = {
+ "gpio48", "gpio49",
+};
+
+static const char * const qdss_traceclk_a_groups[] = {
+ "gpio48",
+};
+
+static const char * const qdss_tracectl_a_groups[] = {
+ "gpio49",
+};
+
+static const char * const pwm01_groups[] = {
+ "gpio50",
+};
+
+static const char * const pta1_1_groups[] = {
+ "gpio51",
+};
+
+static const char * const pwm11_groups[] = {
+ "gpio51",
+};
+
+static const char * const rx1_groups[] = {
+ "gpio51",
+};
+
+static const char * const pta1_2_groups[] = {
+ "gpio52",
+};
+
+static const char * const pwm21_groups[] = {
+ "gpio52",
+};
+
+static const char * const pta1_0_groups[] = {
+ "gpio53",
+};
+
+static const char * const pwm31_groups[] = {
+ "gpio53",
+};
+
+static const char * const prng_rosc_groups[] = {
+ "gpio53",
+};
+
+static const char * const blsp4_uart_groups[] = {
+ "gpio55", "gpio56", "gpio57", "gpio58",
+};
+
+static const char * const blsp4_i2c_groups[] = {
+ "gpio55", "gpio56",
+};
+
+static const char * const blsp4_spi_groups[] = {
+ "gpio55", "gpio56", "gpio57", "gpio58",
+};
+
+static const char * const pcie0_clk_groups[] = {
+ "gpio59",
+};
+
+static const char * const cri_trng0_groups[] = {
+ "gpio59",
+};
+
+static const char * const pcie0_rst_groups[] = {
+ "gpio60",
+};
+
+static const char * const cri_trng1_groups[] = {
+ "gpio60",
+};
+
+static const char * const pcie0_wake_groups[] = {
+ "gpio61",
+};
+
+static const char * const cri_trng_groups[] = {
+ "gpio61",
+};
+
+static const char * const sd_card_groups[] = {
+ "gpio62",
+};
+
+static const char * const sd_write_groups[] = {
+ "gpio63",
+};
+
+static const char * const rx0_groups[] = {
+ "gpio63",
+};
+
+static const char * const tsens_max_groups[] = {
+ "gpio63",
+};
+
+static const char * const mdc_groups[] = {
+ "gpio64",
+};
+
+static const char * const qdss_tracedata_a_groups[] = {
+ "gpio64", "gpio65", "gpio66", "gpio67", "gpio68", "gpio69", "gpio70",
+ "gpio71", "gpio72", "gpio73", "gpio74", "gpio75", "gpio76", "gpio77",
+ "gpio78", "gpio79",
+};
+
+static const char * const mdio_groups[] = {
+ "gpio65",
+};
+
+static const char * const pta2_0_groups[] = {
+ "gpio66",
+};
+
+static const char * const wci21_groups[] = {
+ "gpio66", "gpio68",
+};
+
+static const char * const cxc1_groups[] = {
+ "gpio66", "gpio68",
+};
+
+static const char * const pta2_1_groups[] = {
+ "gpio67",
+};
+
+static const char * const pta2_2_groups[] = {
+ "gpio68",
+};
+
+static const char * const blsp1_uart_groups[] = {
+ "gpio69", "gpio70", "gpio71", "gpio72",
+};
+
+static const char * const blsp1_i2c_groups[] = {
+ "gpio69", "gpio70",
+};
+
+static const char * const blsp1_spi_groups[] = {
+ "gpio69", "gpio70", "gpio71", "gpio72",
+};
+
+static const char * const gcc_plltest_groups[] = {
+ "gpio69", "gpio71",
+};
+
+static const char * const gcc_tlmm_groups[] = {
+ "gpio70",
+};
+
+static const char * const gpio_groups[] = {
+ "gpio0", "gpio1", "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7",
+ "gpio8", "gpio9", "gpio10", "gpio11", "gpio12", "gpio13", "gpio14",
+ "gpio15", "gpio16", "gpio17", "gpio18", "gpio19", "gpio20", "gpio21",
+ "gpio22", "gpio23", "gpio24", "gpio25", "gpio26", "gpio27", "gpio28",
+ "gpio29", "gpio30", "gpio31", "gpio32", "gpio33", "gpio34", "gpio35",
+ "gpio36", "gpio37", "gpio38", "gpio39", "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45", "gpio46", "gpio47", "gpio48", "gpio49",
+ "gpio50", "gpio51", "gpio52", "gpio53", "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio58", "gpio59", "gpio60", "gpio61", "gpio62", "gpio63",
+ "gpio64", "gpio65", "gpio66", "gpio67", "gpio68", "gpio69", "gpio70",
+ "gpio71", "gpio72", "gpio73", "gpio74", "gpio75", "gpio76", "gpio77",
+ "gpio78", "gpio79",
+};
+
+static const struct msm_function ipq6018_functions[] = {
+ FUNCTION(atest_char),
+ FUNCTION(atest_char0),
+ FUNCTION(atest_char1),
+ FUNCTION(atest_char2),
+ FUNCTION(atest_char3),
+ FUNCTION(audio0),
+ FUNCTION(audio1),
+ FUNCTION(audio2),
+ FUNCTION(audio3),
+ FUNCTION(audio_rxbclk),
+ FUNCTION(audio_rxfsync),
+ FUNCTION(audio_rxmclk),
+ FUNCTION(audio_rxmclkin),
+ FUNCTION(audio_txbclk),
+ FUNCTION(audio_txfsync),
+ FUNCTION(audio_txmclk),
+ FUNCTION(audio_txmclkin),
+ FUNCTION(blsp0_i2c),
+ FUNCTION(blsp0_spi),
+ FUNCTION(blsp0_uart),
+ FUNCTION(blsp1_i2c),
+ FUNCTION(blsp1_spi),
+ FUNCTION(blsp1_uart),
+ FUNCTION(blsp2_i2c),
+ FUNCTION(blsp2_spi),
+ FUNCTION(blsp2_uart),
+ FUNCTION(blsp3_i2c),
+ FUNCTION(blsp3_spi),
+ FUNCTION(blsp3_uart),
+ FUNCTION(blsp4_i2c),
+ FUNCTION(blsp4_spi),
+ FUNCTION(blsp4_uart),
+ FUNCTION(blsp5_i2c),
+ FUNCTION(blsp5_uart),
+ FUNCTION(burn0),
+ FUNCTION(burn1),
+ FUNCTION(cri_trng),
+ FUNCTION(cri_trng0),
+ FUNCTION(cri_trng1),
+ FUNCTION(cxc0),
+ FUNCTION(cxc1),
+ FUNCTION(dbg_out),
+ FUNCTION(gcc_plltest),
+ FUNCTION(gcc_tlmm),
+ FUNCTION(gpio),
+ FUNCTION(lpass_aud),
+ FUNCTION(lpass_aud0),
+ FUNCTION(lpass_aud1),
+ FUNCTION(lpass_aud2),
+ FUNCTION(lpass_pcm),
+ FUNCTION(lpass_pdm),
+ FUNCTION(mac00),
+ FUNCTION(mac01),
+ FUNCTION(mac10),
+ FUNCTION(mac11),
+ FUNCTION(mac12),
+ FUNCTION(mac13),
+ FUNCTION(mac20),
+ FUNCTION(mac21),
+ FUNCTION(mdc),
+ FUNCTION(mdio),
+ FUNCTION(pcie0_clk),
+ FUNCTION(pcie0_rst),
+ FUNCTION(pcie0_wake),
+ FUNCTION(prng_rosc),
+ FUNCTION(pta1_0),
+ FUNCTION(pta1_1),
+ FUNCTION(pta1_2),
+ FUNCTION(pta2_0),
+ FUNCTION(pta2_1),
+ FUNCTION(pta2_2),
+ FUNCTION(pwm00),
+ FUNCTION(pwm01),
+ FUNCTION(pwm02),
+ FUNCTION(pwm03),
+ FUNCTION(pwm04),
+ FUNCTION(pwm10),
+ FUNCTION(pwm11),
+ FUNCTION(pwm12),
+ FUNCTION(pwm13),
+ FUNCTION(pwm14),
+ FUNCTION(pwm20),
+ FUNCTION(pwm21),
+ FUNCTION(pwm22),
+ FUNCTION(pwm23),
+ FUNCTION(pwm24),
+ FUNCTION(pwm30),
+ FUNCTION(pwm31),
+ FUNCTION(pwm32),
+ FUNCTION(pwm33),
+ FUNCTION(qdss_cti_trig_in_a0),
+ FUNCTION(qdss_cti_trig_in_a1),
+ FUNCTION(qdss_cti_trig_out_a0),
+ FUNCTION(qdss_cti_trig_out_a1),
+ FUNCTION(qdss_cti_trig_in_b0),
+ FUNCTION(qdss_cti_trig_in_b1),
+ FUNCTION(qdss_cti_trig_out_b0),
+ FUNCTION(qdss_cti_trig_out_b1),
+ FUNCTION(qdss_traceclk_a),
+ FUNCTION(qdss_tracectl_a),
+ FUNCTION(qdss_tracedata_a),
+ FUNCTION(qdss_traceclk_b),
+ FUNCTION(qdss_tracectl_b),
+ FUNCTION(qdss_tracedata_b),
+ FUNCTION(qpic_pad),
+ FUNCTION(rx0),
+ FUNCTION(rx1),
+ FUNCTION(rx_swrm),
+ FUNCTION(rx_swrm0),
+ FUNCTION(rx_swrm1),
+ FUNCTION(sd_card),
+ FUNCTION(sd_write),
+ FUNCTION(tsens_max),
+ FUNCTION(tx_swrm),
+ FUNCTION(tx_swrm0),
+ FUNCTION(tx_swrm1),
+ FUNCTION(tx_swrm2),
+ FUNCTION(wci20),
+ FUNCTION(wci21),
+ FUNCTION(wci22),
+ FUNCTION(wci23),
+ FUNCTION(wsa_swrm),
+};
+
+static const struct msm_pingroup ipq6018_groups[] = {
+ PINGROUP(0, qpic_pad, wci20, qdss_traceclk_b, _, burn0, _, _, _, _),
+ PINGROUP(1, qpic_pad, mac12, qdss_tracectl_b, _, burn1, _, _, _, _),
+ PINGROUP(2, qpic_pad, wci20, qdss_tracedata_b, _, _, _, _, _, _),
+ PINGROUP(3, qpic_pad, mac01, qdss_tracedata_b, _, _, _, _, _, _),
+ PINGROUP(4, qpic_pad, mac01, qdss_tracedata_b, _, _, _, _, _, _),
+ PINGROUP(5, qpic_pad, mac21, qdss_tracedata_b, _, _, _, _, _, _),
+ PINGROUP(6, qpic_pad, mac21, qdss_tracedata_b, _, _, _, _, _, _),
+ PINGROUP(7, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
+ PINGROUP(8, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
+ PINGROUP(9, qpic_pad, atest_char, cxc0, mac13, dbg_out, qdss_tracedata_b, _, _, _),
+ PINGROUP(10, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
+ PINGROUP(11, qpic_pad, wci22, mac12, qdss_tracedata_b, _, _, _, _, _),
+ PINGROUP(12, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
+ PINGROUP(13, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
+ PINGROUP(14, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
+ PINGROUP(15, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
+ PINGROUP(16, qpic_pad, cxc0, mac13, qdss_tracedata_b, _, _, _, _, _),
+ PINGROUP(17, qpic_pad, qdss_tracedata_b, wci22, _, _, _, _, _, _),
+ PINGROUP(18, pwm00, atest_char0, wci23, mac11, _, _, _, _, _),
+ PINGROUP(19, pwm10, atest_char1, wci23, mac11, _, _, _, _, _),
+ PINGROUP(20, pwm20, atest_char2, _, _, _, _, _, _, _),
+ PINGROUP(21, pwm30, atest_char3, _, _, _, _, _, _, _),
+ PINGROUP(22, audio_txmclk, audio_txmclkin, pwm02, tx_swrm0, _, qdss_cti_trig_out_b0, _, _, _),
+ PINGROUP(23, audio_txbclk, pwm12, wsa_swrm, tx_swrm1, _, qdss_cti_trig_in_b0, _, _, _),
+ PINGROUP(24, audio_txfsync, pwm22, wsa_swrm, tx_swrm2, _, qdss_cti_trig_out_b1, _, _, _),
+ PINGROUP(25, audio0, pwm32, tx_swrm, _, qdss_cti_trig_in_b1, _, _, _, _),
+ PINGROUP(26, audio1, pwm04, _, _, _, _, _, _, _),
+ PINGROUP(27, audio2, pwm14, _, _, _, _, _, _, _),
+ PINGROUP(28, audio3, pwm24, _, _, _, _, _, _, _),
+ PINGROUP(29, audio_rxmclk, audio_rxmclkin, pwm03, lpass_pdm, lpass_aud, qdss_cti_trig_in_a1, _, _, _),
+ PINGROUP(30, audio_rxbclk, pwm13, lpass_pdm, lpass_aud0, rx_swrm, _, qdss_cti_trig_out_a1, _, _),
+ PINGROUP(31, audio_rxfsync, pwm23, lpass_pdm, lpass_aud1, rx_swrm0, _, qdss_cti_trig_in_a0, _, _),
+ PINGROUP(32, audio0, pwm33, lpass_pdm, lpass_aud2, rx_swrm1, _, qdss_cti_trig_out_a0, _, _),
+ PINGROUP(33, audio1, _, _, _, _, _, _, _, _),
+ PINGROUP(34, lpass_pcm, mac10, mac00, _, _, _, _, _, _),
+ PINGROUP(35, lpass_pcm, mac10, mac00, _, _, _, _, _, _),
+ PINGROUP(36, lpass_pcm, mac20, _, _, _, _, _, _, _),
+ PINGROUP(37, lpass_pcm, mac20, _, _, _, _, _, _, _),
+ PINGROUP(38, blsp0_uart, blsp0_i2c, blsp0_spi, _, _, _, _, _, _),
+ PINGROUP(39, blsp0_uart, blsp0_i2c, blsp0_spi, _, _, _, _, _, _),
+ PINGROUP(40, blsp0_uart, blsp0_spi, _, _, _, _, _, _, _),
+ PINGROUP(41, blsp0_uart, blsp0_spi, _, _, _, _, _, _, _),
+ PINGROUP(42, blsp2_uart, blsp2_i2c, blsp2_spi, _, _, _, _, _, _),
+ PINGROUP(43, blsp2_uart, blsp2_i2c, blsp2_spi, _, _, _, _, _, _),
+ PINGROUP(44, blsp2_uart, blsp2_spi, _, _, _, _, _, _, _),
+ PINGROUP(45, blsp2_uart, blsp2_spi, _, _, _, _, _, _, _),
+ PINGROUP(46, blsp5_i2c, _, _, _, _, _, _, _, _),
+ PINGROUP(47, blsp5_i2c, _, _, _, _, _, _, _, _),
+ PINGROUP(48, blsp5_uart, _, qdss_traceclk_a, _, _, _, _, _, _),
+ PINGROUP(49, blsp5_uart, _, qdss_tracectl_a, _, _, _, _, _, _),
+ PINGROUP(50, pwm01, _, _, _, _, _, _, _, _),
+ PINGROUP(51, pta1_1, pwm11, _, rx1, _, _, _, _, _),
+ PINGROUP(52, pta1_2, pwm21, _, _, _, _, _, _, _),
+ PINGROUP(53, pta1_0, pwm31, prng_rosc, _, _, _, _, _, _),
+ PINGROUP(54, _, _, _, _, _, _, _, _, _),
+ PINGROUP(55, blsp4_uart, blsp4_i2c, blsp4_spi, _, _, _, _, _, _),
+ PINGROUP(56, blsp4_uart, blsp4_i2c, blsp4_spi, _, _, _, _, _, _),
+ PINGROUP(57, blsp4_uart, blsp4_spi, _, _, _, _, _, _, _),
+ PINGROUP(58, blsp4_uart, blsp4_spi, _, _, _, _, _, _, _),
+ PINGROUP(59, pcie0_clk, _, _, cri_trng0, _, _, _, _, _),
+ PINGROUP(60, pcie0_rst, _, _, cri_trng1, _, _, _, _, _),
+ PINGROUP(61, pcie0_wake, _, _, cri_trng, _, _, _, _, _),
+ PINGROUP(62, sd_card, _, _, _, _, _, _, _, _),
+ PINGROUP(63, sd_write, rx0, _, tsens_max, _, _, _, _, _),
+ PINGROUP(64, mdc, _, qdss_tracedata_a, _, _, _, _, _, _),
+ PINGROUP(65, mdio, _, qdss_tracedata_a, _, _, _, _, _, _),
+ PINGROUP(66, pta2_0, wci21, cxc1, qdss_tracedata_a, _, _, _, _, _),
+ PINGROUP(67, pta2_1, qdss_tracedata_a, _, _, _, _, _, _, _),
+ PINGROUP(68, pta2_2, wci21, cxc1, qdss_tracedata_a, _, _, _, _, _),
+ PINGROUP(69, blsp1_uart, blsp1_i2c, blsp1_spi, gcc_plltest, qdss_tracedata_a, _, _, _, _),
+ PINGROUP(70, blsp1_uart, blsp1_i2c, blsp1_spi, gcc_tlmm, qdss_tracedata_a, _, _, _, _),
+ PINGROUP(71, blsp1_uart, blsp1_spi, gcc_plltest, qdss_tracedata_a, _, _, _, _, _),
+ PINGROUP(72, blsp1_uart, blsp1_spi, qdss_tracedata_a, _, _, _, _, _, _),
+ PINGROUP(73, blsp3_uart, blsp3_i2c, blsp3_spi, _, qdss_tracedata_a, _, _, _, _),
+ PINGROUP(74, blsp3_uart, blsp3_i2c, blsp3_spi, _, qdss_tracedata_a, _, _, _, _),
+ PINGROUP(75, blsp3_uart, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _),
+ PINGROUP(76, blsp3_uart, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _),
+ PINGROUP(77, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _, _),
+ PINGROUP(78, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _, _),
+ PINGROUP(79, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _, _),
+};
+
+static const struct msm_pinctrl_soc_data ipq6018_pinctrl = {
+ .pins = ipq6018_pins,
+ .npins = ARRAY_SIZE(ipq6018_pins),
+ .functions = ipq6018_functions,
+ .nfunctions = ARRAY_SIZE(ipq6018_functions),
+ .groups = ipq6018_groups,
+ .ngroups = ARRAY_SIZE(ipq6018_groups),
+ .ngpios = 80,
+};
+
+static int ipq6018_pinctrl_probe(struct platform_device *pdev)
+{
+ return msm_pinctrl_probe(pdev, &ipq6018_pinctrl);
+}
+
+static const struct of_device_id ipq6018_pinctrl_of_match[] = {
+ { .compatible = "qcom,ipq6018-pinctrl", },
+ { },
+};
+
+static struct platform_driver ipq6018_pinctrl_driver = {
+ .driver = {
+ .name = "ipq6018-pinctrl",
+ .of_match_table = ipq6018_pinctrl_of_match,
+ },
+ .probe = ipq6018_pinctrl_probe,
+ .remove = msm_pinctrl_remove,
+};
+
+static int __init ipq6018_pinctrl_init(void)
+{
+ return platform_driver_register(&ipq6018_pinctrl_driver);
+}
+arch_initcall(ipq6018_pinctrl_init);
+
+static void __exit ipq6018_pinctrl_exit(void)
+{
+ platform_driver_unregister(&ipq6018_pinctrl_driver);
+}
+module_exit(ipq6018_pinctrl_exit);
+
+MODULE_DESCRIPTION("QTI ipq6018 pinctrl driver");
+MODULE_LICENSE("GPL v2");
+MODULE_DEVICE_TABLE(of, ipq6018_pinctrl_of_match);
--
1.9.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH V3 3/5] dt-bindings: qcom: Add ipq6018 bindings
2020-01-03 11:49 [PATCH V3 0/5] Add minimal boot support for IPQ6018 Sricharan R
2020-01-03 11:49 ` [PATCH V3 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings Sricharan R
2020-01-03 11:49 ` [PATCH V3 2/5] pinctrl: qcom: Add ipq6018 pinctrl driver Sricharan R
@ 2020-01-03 11:49 ` Sricharan R
2020-01-04 0:59 ` Rob Herring
2020-01-03 11:49 ` [PATCH V3 4/5] arm64: dts: Add ipq6018 SoC and CP01 board support Sricharan R
2020-01-03 11:49 ` [PATCH V3 5/5] arm64: defconfig: Enable qcom ipq6018 clock and pinctrl Sricharan R
4 siblings, 1 reply; 12+ messages in thread
From: Sricharan R @ 2020-01-03 11:49 UTC (permalink / raw)
To: sricharan, agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-clk, linux-gpio, linux-kernel, linux-soc,
robh+dt, sboyd, sivaprak
Document the new ipq6018 SOC/board device tree bindings.
Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
---
Documentation/devicetree/bindings/arm/qcom.yaml | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 529d924..164177e 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -28,6 +28,7 @@ description: |
apq8074
apq8084
apq8096
+ ipq6018
ipq8074
mdm9615
msm8916
@@ -41,6 +42,7 @@ description: |
The 'board' element must be one of the following strings:
cdp
+ cp01-c1
dragonboard
hk01
idp
@@ -150,4 +152,10 @@ properties:
- enum:
- qcom,sc7180-idp
- const: qcom,sc7180
+
+ - items:
+ - enum:
+ - qcom,ipq6018-cp01-c1
+ - const: qcom,ipq6018
+
...
--
1.9.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH V3 4/5] arm64: dts: Add ipq6018 SoC and CP01 board support
2020-01-03 11:49 [PATCH V3 0/5] Add minimal boot support for IPQ6018 Sricharan R
` (2 preceding siblings ...)
2020-01-03 11:49 ` [PATCH V3 3/5] dt-bindings: qcom: Add ipq6018 bindings Sricharan R
@ 2020-01-03 11:49 ` Sricharan R
2020-01-03 11:49 ` [PATCH V3 5/5] arm64: defconfig: Enable qcom ipq6018 clock and pinctrl Sricharan R
4 siblings, 0 replies; 12+ messages in thread
From: Sricharan R @ 2020-01-03 11:49 UTC (permalink / raw)
To: sricharan, agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-clk, linux-gpio, linux-kernel, linux-soc,
robh+dt, sboyd, sivaprak
Add initial device tree support for the Qualcomm IPQ6018 SoC and
CP01 evaluation board.
Co-developed-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
---
[v3] Fixed the uart pinctrl node, moved soc node down the
tree. This has build dependency with,
https://patchwork.ozlabs.org/patch/1217293/
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts | 30 ++++
arch/arm64/boot/dts/qcom/ipq6018.dtsi | 215 +++++++++++++++++++++++++++
3 files changed, 246 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
create mode 100644 arch/arm64/boot/dts/qcom/ipq6018.dtsi
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 7a5c2f7..48acb49 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -1,6 +1,7 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb
+dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8150.dtb
diff --git a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
new file mode 100644
index 0000000..897b4b2
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * IPQ6018 CP01 board device tree source
+ *
+ * Copyright (c) 2019, The Linux Foundation. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "ipq6018.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. IPQ6018/AP-CP01-C1";
+ compatible = "qcom,ipq6018-cp01", "qcom,ipq6018";
+
+ aliases {
+ serial0 = &blsp1_uart3;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs-append = " swiotlb=1";
+ };
+};
+
+&blsp1_uart3 {
+ pinctrl-0 = <&serial_3_pins>;
+ pinctrl-names = "default";
+ status = "ok";
+};
diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
new file mode 100644
index 0000000..78fa30e
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
@@ -0,0 +1,215 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * IPQ6018 SoC device tree source
+ *
+ * Copyright (c) 2019, The Linux Foundation. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-ipq6018.h>
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&intc>;
+
+ clocks {
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <32000>;
+ #clock-cells = <0>;
+ };
+
+ xo: xo {
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ #clock-cells = <0>;
+ };
+ };
+
+ cpus: cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ CPU0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0>;
+ enable-method = "psci";
+ next-level-cache = <&L2_0>;
+ };
+
+ CPU1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x1>;
+ next-level-cache = <&L2_0>;
+ };
+
+ CPU2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x2>;
+ next-level-cache = <&L2_0>;
+ };
+
+ CPU3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x3>;
+ next-level-cache = <&L2_0>;
+ };
+
+ L2_0: l2-cache {
+ compatible = "cache";
+ cache-level = <0x2>;
+ };
+ };
+
+ pmuv8: pmu {
+ compatible = "arm,cortex-a53-pmu";
+ interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) |
+ IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ psci: psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ tz: tz@48500000 {
+ reg = <0x0 0x48500000 0x0 0x00200000>;
+ no-map;
+ };
+ };
+
+ soc: soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0 0xffffffff>;
+ dma-ranges;
+ compatible = "simple-bus";
+
+ tlmm: pinctrl@1000000 {
+ compatible = "qcom,ipq6018-pinctrl";
+ reg = <0x01000000 0x300000>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&tlmm 0 80>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ serial_3_pins: serial3-pinmux {
+ pins = "gpio44", "gpio45";
+ function = "blsp2_uart";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+ };
+
+ gcc: gcc@1800000 {
+ compatible = "qcom,gcc-ipq6018";
+ reg = <0x01800000 0x80000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ blsp1_uart3: serial@78b1000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x078b1000 0x200>;
+ interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+
+ intc: interrupt-controller@b000000 {
+ compatible = "qcom,msm-qgic2";
+ interrupt-controller;
+ #interrupt-cells = <0x3>;
+ reg = <0x0b000000 0x1000>, /*GICD*/
+ <0x0b002000 0x1000>, /*GICC*/
+ <0x0b001000 0x1000>, /*GICH*/
+ <0x0b004000 0x1000>; /*GICV*/
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ timer@b120000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ compatible = "arm,armv7-timer-mem";
+ reg = <0x0b120000 0x1000>;
+ clock-frequency = <19200000>;
+
+ frame@b120000 {
+ frame-number = <0>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b121000 0x1000>,
+ <0x0b122000 0x1000>;
+ };
+
+ frame@b123000 {
+ frame-number = <1>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0xb123000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@b124000 {
+ frame-number = <2>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b124000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@b125000 {
+ frame-number = <3>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b125000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@b126000 {
+ frame-number = <4>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b126000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@b127000 {
+ frame-number = <5>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b127000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@b128000 {
+ frame-number = <6>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b128000 0x1000>;
+ status = "disabled";
+ };
+ };
+
+ };
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH V3 5/5] arm64: defconfig: Enable qcom ipq6018 clock and pinctrl
2020-01-03 11:49 [PATCH V3 0/5] Add minimal boot support for IPQ6018 Sricharan R
` (3 preceding siblings ...)
2020-01-03 11:49 ` [PATCH V3 4/5] arm64: dts: Add ipq6018 SoC and CP01 board support Sricharan R
@ 2020-01-03 11:49 ` Sricharan R
4 siblings, 0 replies; 12+ messages in thread
From: Sricharan R @ 2020-01-03 11:49 UTC (permalink / raw)
To: sricharan, agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-clk, linux-gpio, linux-kernel, linux-soc,
robh+dt, sboyd, sivaprak
These configs are required for booting kernel in qcom
ipq6018 boards.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
---
arch/arm64/configs/defconfig | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index f123840..631372c 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -403,6 +403,7 @@ CONFIG_PINCTRL_IMX8MN=y
CONFIG_PINCTRL_IMX8MQ=y
CONFIG_PINCTRL_IMX8QXP=y
CONFIG_PINCTRL_IPQ8074=y
+CONFIG_PINCTRL_IPQ6018=y
CONFIG_PINCTRL_MSM8916=y
CONFIG_PINCTRL_MSM8994=y
CONFIG_PINCTRL_MSM8996=y
@@ -709,6 +710,7 @@ CONFIG_QCOM_CLK_APCS_MSM8916=y
CONFIG_QCOM_CLK_SMD_RPM=y
CONFIG_QCOM_CLK_RPMH=y
CONFIG_IPQ_GCC_8074=y
+CONFIG_IPQ_GCC_6018=y
CONFIG_MSM_GCC_8916=y
CONFIG_MSM_GCC_8994=y
CONFIG_MSM_MMCC_8996=y
--
1.9.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH V3 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings
2020-01-03 11:49 ` [PATCH V3 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings Sricharan R
@ 2020-01-04 0:58 ` Rob Herring
2020-01-06 5:25 ` Sricharan R
2020-01-07 11:55 ` Linus Walleij
1 sibling, 1 reply; 12+ messages in thread
From: Rob Herring @ 2020-01-04 0:58 UTC (permalink / raw)
To: Sricharan R
Cc: agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-clk, linux-gpio, linux-kernel, linux-soc,
sboyd, sivaprak
On Fri, Jan 03, 2020 at 05:19:33PM +0530, Sricharan R wrote:
> Add device tree binding Documentation details for ipq6018
> pinctrl driver.
>
> Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
> Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
> Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
> Signed-off-by: Sricharan R <sricharan@codeaurora.org>
> ---
> [v3] Fixed the example dt node, inherited properties
>
> .../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml | 166 +++++++++++++++++++++
> 1 file changed, 166 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
> new file mode 100644
> index 0000000..e959c5f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
> @@ -0,0 +1,166 @@
> +# SPDX-License-Identifier: GPL-2.0-or-later
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/qcom,ipq6018-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm Technologies, Inc. IPQ6018 TLMM block
> +
> +maintainers:
> + - Sricharan R <sricharan@codeaurora.org>
> +
> +description: |
> + This binding describes the Top Level Mode Multiplexer block found in the
> + IPQ6018 platform.
> +
> +properties:
> + compatible:
> + const: qcom,ipq6018-pinctrl
A blank line after each property schema is preferred.
> + reg:
> + maxItems: 1
> + interrupts:
> + Description: Specifies the TLMM summary IRQ
> + maxItems: 1
> + interrupt-controller: true
> + '#interrupt-cells':
> + Description:
> + Specifies the PIN numbers and Flags, as defined in defined in
> + include/dt-bindings/interrupt-controller/irq.h
> + const: 2
> + gpio-controller: true
> + '#gpio-cells':
> + Description: Specifying the pin number and flags, as defined in
> + include/dt-bindings/gpio/gpio.h
> + const: 2
> + gpio-ranges:
> + Description: Documentation/devicetree/bindings/gpio/gpio.txt
> + maxItems: 1
> +
> +#PIN CONFIGURATION NODES
> +patternProperties:
> + '-pins$':
> + type: object
> + Description:
> + Pinctrl node's client devices use subnodes for desired pin configuration.
> + Client device subnodes use below standard properties.
> +
> + Properties:
Did you run 'make dt_binding_check' and is dt-schema up to date? This
isn't valid json-schema which is case sensitive.
> + pins:
> + allOf:
> + $ref: /schemas/types.yaml#/definitions/string
Also not valid as allOf is a list.
> + enum:
> + gpio0-gpio80
As is 'enum'...
> + sdc1_clk
> + sdc1_cmd
> + sdc1_data
> + sdc2_clk
> + sdc2_cmd
> + sdc2_data
> + qdsd_cmd
> + qdsd_data0
> + qdsd_data1
> + qdsd_data2
> + qdsd_data3
> + Description:
> + List of gpio pins affected by the properties specified in this
> + subnode.
> +
> + function:
> + allOf:
> + $ref: /schemas/types.yaml#/definitions/string
> + enum:
> + adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char,
> + atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac,
> + atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0,
> + atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp_i2c1,
> + blsp_i2c2, blsp_i2c3, blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_spi1,
> + blsp_spi1_cs1, blsp_spi1_cs2, blsp_spi1_cs3, blsp_spi2,
> + blsp_spi2_cs1, blsp_spi2_cs2, blsp_spi2_cs3, blsp_spi3,
> + blsp_spi3_cs1, blsp_spi3_cs2, blsp_spi3_cs3, blsp_spi4, blsp_spi5,
> + blsp_spi6, blsp_uart1, blsp_uart2, blsp_uim1, blsp_uim2, cam1_rst,
> + cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0,
> + cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v,
> + dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass,
> + flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a,
> + gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0,
> + gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2,
> + ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc,
> + nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s,
> + pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
> + pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a,
> + pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1,
> + qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0,
> + qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1,
> + qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b,
> + qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write,
> + sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3,
> + uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst
> + Description:
> + Specify the alternative function to be configured for the specified
> + pins.
> + bias-disable:
> + allOf:
> + $ref: /schemas/pinctrl/pincfg-node.yaml
While you should have this reference, it is at the wrong level. The node
needs to reference this schema, not the properties.
> + Description:
> + The specified pins should be configured as no pull.
> + bias-pull-down:
> + allOf:
> + $ref: /schemas/pinctrl/pincfg-node.yaml
> + Description:
> + The specified pins should be configured as pull down.
> + bias-pull-up:
> + allOf:
> + $ref: /schemas/pinctrl/pincfg-node.yaml
> + Description:
> + The specified pins should be configured as pull up.
> + output-high:
> + allOf:
> + $ref: /schemas/pinctrl/pincfg-node.yaml
> + Description:
> + The specified pins are configured in output mode, driven high.
> + This option is not available for sdc pins.
> + output-low:
> + allOf:
> + $ref: /schemas/pinctrl/pincfg-node.yaml
> + Description:
> + The specified pins are configured in output mode, driven low.
> + This option is not available for sdc pins.
> + drive-strength:
> + allOf:
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [2, 4, 6, 8, 10, 12, 14, 16]
> + Description:
> + Selects the drive strength for the specified pins, in mA.
> +
> + required:
> + - pins
> + - function
> +
> +required:
> + - compatible
> + - reg
> + - interrupts
> + - interrupt-controller
> + - '#interrupt-cells'
> + - gpio-controller
> + - '#gpio-cells'
> + - gpio-ranges
> +
> +example:
> + tlmm: pinctrl@1000000 {
> + compatible = "qcom,ipq6018-pinctrl";
> + reg = <0x01000000 0x300000>;
> + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&tlmm 0 80>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + serial_3_pins: serial3-pinmux {
> + pins = "gpio44", "gpio45";
> + function = "blsp2_uart";
> + drive-strength = <8>;
> + bias-pull-down;
> + };
> + };
> --
> 1.9.1
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH V3 3/5] dt-bindings: qcom: Add ipq6018 bindings
2020-01-03 11:49 ` [PATCH V3 3/5] dt-bindings: qcom: Add ipq6018 bindings Sricharan R
@ 2020-01-04 0:59 ` Rob Herring
0 siblings, 0 replies; 12+ messages in thread
From: Rob Herring @ 2020-01-04 0:59 UTC (permalink / raw)
To: Sricharan R
Cc: sricharan, agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-clk, linux-gpio, linux-kernel, linux-soc,
robh+dt, sboyd, sivaprak
On Fri, 3 Jan 2020 17:19:35 +0530, Sricharan R wrote:
> Document the new ipq6018 SOC/board device tree bindings.
>
> Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
> Signed-off-by: Sricharan R <sricharan@codeaurora.org>
> ---
> Documentation/devicetree/bindings/arm/qcom.yaml | 8 ++++++++
> 1 file changed, 8 insertions(+)
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH V3 2/5] pinctrl: qcom: Add ipq6018 pinctrl driver
2020-01-03 11:49 ` [PATCH V3 2/5] pinctrl: qcom: Add ipq6018 pinctrl driver Sricharan R
@ 2020-01-04 1:33 ` Bjorn Andersson
0 siblings, 0 replies; 12+ messages in thread
From: Bjorn Andersson @ 2020-01-04 1:33 UTC (permalink / raw)
To: Sricharan R
Cc: agross, devicetree, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-clk, linux-gpio, linux-kernel, linux-soc,
robh+dt, sboyd, sivaprak
On Fri 03 Jan 03:49 PST 2020, Sricharan R wrote:
> Add initial pinctrl driver to support pin configuration with
> pinctrl framework for ipq6018.
>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
> Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
> Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
> Signed-off-by: Sricharan R <sricharan@codeaurora.org>
> ---
> [v3] Removed qpic_padN
>
> drivers/pinctrl/qcom/Kconfig | 10 +
> drivers/pinctrl/qcom/Makefile | 1 +
> drivers/pinctrl/qcom/pinctrl-ipq6018.c | 1107 ++++++++++++++++++++++++++++++++
> 3 files changed, 1118 insertions(+)
> create mode 100644 drivers/pinctrl/qcom/pinctrl-ipq6018.c
>
> diff --git a/drivers/pinctrl/qcom/Kconfig b/drivers/pinctrl/qcom/Kconfig
> index 811af2f8..c5d4428 100644
> --- a/drivers/pinctrl/qcom/Kconfig
> +++ b/drivers/pinctrl/qcom/Kconfig
> @@ -50,6 +50,16 @@ config PINCTRL_IPQ8074
> Qualcomm Technologies Inc. IPQ8074 platform. Select this for
> IPQ8074.
>
> +config PINCTRL_IPQ6018
> + tristate "Qualcomm Technologies, Inc. IPQ6018 pin controller driver"
> + depends on GPIOLIB && OF
> + select PINCTRL_MSM
> + help
> + This is the pinctrl, pinmux, pinconf and gpiolib driver for
> + the Qualcomm Technologies Inc. TLMM block found on the
> + Qualcomm Technologies Inc. IPQ6018 platform. Select this for
> + IPQ6018.
> +
> config PINCTRL_MSM8660
> tristate "Qualcomm 8660 pin controller driver"
> depends on GPIOLIB && OF
> diff --git a/drivers/pinctrl/qcom/Makefile b/drivers/pinctrl/qcom/Makefile
> index c2c2f9a..d9e0904 100644
> --- a/drivers/pinctrl/qcom/Makefile
> +++ b/drivers/pinctrl/qcom/Makefile
> @@ -6,6 +6,7 @@ obj-$(CONFIG_PINCTRL_APQ8084) += pinctrl-apq8084.o
> obj-$(CONFIG_PINCTRL_IPQ4019) += pinctrl-ipq4019.o
> obj-$(CONFIG_PINCTRL_IPQ8064) += pinctrl-ipq8064.o
> obj-$(CONFIG_PINCTRL_IPQ8074) += pinctrl-ipq8074.o
> +obj-$(CONFIG_PINCTRL_IPQ6018) += pinctrl-ipq6018.o
> obj-$(CONFIG_PINCTRL_MSM8660) += pinctrl-msm8660.o
> obj-$(CONFIG_PINCTRL_MSM8960) += pinctrl-msm8960.o
> obj-$(CONFIG_PINCTRL_MSM8X74) += pinctrl-msm8x74.o
> diff --git a/drivers/pinctrl/qcom/pinctrl-ipq6018.c b/drivers/pinctrl/qcom/pinctrl-ipq6018.c
> new file mode 100644
> index 0000000..38c33a7
> --- /dev/null
> +++ b/drivers/pinctrl/qcom/pinctrl-ipq6018.c
> @@ -0,0 +1,1107 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2016-2018, The Linux Foundation. All rights reserved.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/pinctrl/pinctrl.h>
> +
> +#include "pinctrl-msm.h"
> +
> +#define FUNCTION(fname) \
> + [msm_mux_##fname] = { \
> + .name = #fname, \
> + .groups = fname##_groups, \
> + .ngroups = ARRAY_SIZE(fname##_groups), \
> + }
> +
> +#define REG_SIZE 0x1000
> +#define PINGROUP(id, f1, f2, f3, f4, f5, f6, f7, f8, f9) \
> + { \
> + .name = "gpio" #id, \
> + .pins = gpio##id##_pins, \
> + .npins = (unsigned int)ARRAY_SIZE(gpio##id##_pins), \
> + .funcs = (int[]){ \
> + msm_mux_gpio, /* gpio mode */ \
> + msm_mux_##f1, \
> + msm_mux_##f2, \
> + msm_mux_##f3, \
> + msm_mux_##f4, \
> + msm_mux_##f5, \
> + msm_mux_##f6, \
> + msm_mux_##f7, \
> + msm_mux_##f8, \
> + msm_mux_##f9 \
> + }, \
> + .nfuncs = 10, \
> + .ctl_reg = REG_SIZE * id, \
> + .io_reg = 0x4 + REG_SIZE * id, \
> + .intr_cfg_reg = 0x8 + REG_SIZE * id, \
> + .intr_status_reg = 0xc + REG_SIZE * id, \
> + .intr_target_reg = 0x8 + REG_SIZE * id, \
> + .mux_bit = 2, \
> + .pull_bit = 0, \
> + .drv_bit = 6, \
> + .oe_bit = 9, \
> + .in_bit = 0, \
> + .out_bit = 1, \
> + .intr_enable_bit = 0, \
> + .intr_status_bit = 0, \
> + .intr_target_bit = 5, \
> + .intr_target_kpss_val = 3, \
> + .intr_raw_status_bit = 4, \
> + .intr_polarity_bit = 1, \
> + .intr_detection_bit = 2, \
> + .intr_detection_width = 2, \
> + }
> +
> +static const struct pinctrl_pin_desc ipq6018_pins[] = {
> + PINCTRL_PIN(0, "GPIO_0"),
> + PINCTRL_PIN(1, "GPIO_1"),
> + PINCTRL_PIN(2, "GPIO_2"),
> + PINCTRL_PIN(3, "GPIO_3"),
> + PINCTRL_PIN(4, "GPIO_4"),
> + PINCTRL_PIN(5, "GPIO_5"),
> + PINCTRL_PIN(6, "GPIO_6"),
> + PINCTRL_PIN(7, "GPIO_7"),
> + PINCTRL_PIN(8, "GPIO_8"),
> + PINCTRL_PIN(9, "GPIO_9"),
> + PINCTRL_PIN(10, "GPIO_10"),
> + PINCTRL_PIN(11, "GPIO_11"),
> + PINCTRL_PIN(12, "GPIO_12"),
> + PINCTRL_PIN(13, "GPIO_13"),
> + PINCTRL_PIN(14, "GPIO_14"),
> + PINCTRL_PIN(15, "GPIO_15"),
> + PINCTRL_PIN(16, "GPIO_16"),
> + PINCTRL_PIN(17, "GPIO_17"),
> + PINCTRL_PIN(18, "GPIO_18"),
> + PINCTRL_PIN(19, "GPIO_19"),
> + PINCTRL_PIN(20, "GPIO_20"),
> + PINCTRL_PIN(21, "GPIO_21"),
> + PINCTRL_PIN(22, "GPIO_22"),
> + PINCTRL_PIN(23, "GPIO_23"),
> + PINCTRL_PIN(24, "GPIO_24"),
> + PINCTRL_PIN(25, "GPIO_25"),
> + PINCTRL_PIN(26, "GPIO_26"),
> + PINCTRL_PIN(27, "GPIO_27"),
> + PINCTRL_PIN(28, "GPIO_28"),
> + PINCTRL_PIN(29, "GPIO_29"),
> + PINCTRL_PIN(30, "GPIO_30"),
> + PINCTRL_PIN(31, "GPIO_31"),
> + PINCTRL_PIN(32, "GPIO_32"),
> + PINCTRL_PIN(33, "GPIO_33"),
> + PINCTRL_PIN(34, "GPIO_34"),
> + PINCTRL_PIN(35, "GPIO_35"),
> + PINCTRL_PIN(36, "GPIO_36"),
> + PINCTRL_PIN(37, "GPIO_37"),
> + PINCTRL_PIN(38, "GPIO_38"),
> + PINCTRL_PIN(39, "GPIO_39"),
> + PINCTRL_PIN(40, "GPIO_40"),
> + PINCTRL_PIN(41, "GPIO_41"),
> + PINCTRL_PIN(42, "GPIO_42"),
> + PINCTRL_PIN(43, "GPIO_43"),
> + PINCTRL_PIN(44, "GPIO_44"),
> + PINCTRL_PIN(45, "GPIO_45"),
> + PINCTRL_PIN(46, "GPIO_46"),
> + PINCTRL_PIN(47, "GPIO_47"),
> + PINCTRL_PIN(48, "GPIO_48"),
> + PINCTRL_PIN(49, "GPIO_49"),
> + PINCTRL_PIN(50, "GPIO_50"),
> + PINCTRL_PIN(51, "GPIO_51"),
> + PINCTRL_PIN(52, "GPIO_52"),
> + PINCTRL_PIN(53, "GPIO_53"),
> + PINCTRL_PIN(54, "GPIO_54"),
> + PINCTRL_PIN(55, "GPIO_55"),
> + PINCTRL_PIN(56, "GPIO_56"),
> + PINCTRL_PIN(57, "GPIO_57"),
> + PINCTRL_PIN(58, "GPIO_58"),
> + PINCTRL_PIN(59, "GPIO_59"),
> + PINCTRL_PIN(60, "GPIO_60"),
> + PINCTRL_PIN(61, "GPIO_61"),
> + PINCTRL_PIN(62, "GPIO_62"),
> + PINCTRL_PIN(63, "GPIO_63"),
> + PINCTRL_PIN(64, "GPIO_64"),
> + PINCTRL_PIN(65, "GPIO_65"),
> + PINCTRL_PIN(66, "GPIO_66"),
> + PINCTRL_PIN(67, "GPIO_67"),
> + PINCTRL_PIN(68, "GPIO_68"),
> + PINCTRL_PIN(69, "GPIO_69"),
> + PINCTRL_PIN(70, "GPIO_70"),
> + PINCTRL_PIN(71, "GPIO_71"),
> + PINCTRL_PIN(72, "GPIO_72"),
> + PINCTRL_PIN(73, "GPIO_73"),
> + PINCTRL_PIN(74, "GPIO_74"),
> + PINCTRL_PIN(75, "GPIO_75"),
> + PINCTRL_PIN(76, "GPIO_76"),
> + PINCTRL_PIN(77, "GPIO_77"),
> + PINCTRL_PIN(78, "GPIO_78"),
> + PINCTRL_PIN(79, "GPIO_79"),
> +};
> +
> +#define DECLARE_MSM_GPIO_PINS(pin) \
> + static const unsigned int gpio##pin##_pins[] = { pin }
> +DECLARE_MSM_GPIO_PINS(0);
> +DECLARE_MSM_GPIO_PINS(1);
> +DECLARE_MSM_GPIO_PINS(2);
> +DECLARE_MSM_GPIO_PINS(3);
> +DECLARE_MSM_GPIO_PINS(4);
> +DECLARE_MSM_GPIO_PINS(5);
> +DECLARE_MSM_GPIO_PINS(6);
> +DECLARE_MSM_GPIO_PINS(7);
> +DECLARE_MSM_GPIO_PINS(8);
> +DECLARE_MSM_GPIO_PINS(9);
> +DECLARE_MSM_GPIO_PINS(10);
> +DECLARE_MSM_GPIO_PINS(11);
> +DECLARE_MSM_GPIO_PINS(12);
> +DECLARE_MSM_GPIO_PINS(13);
> +DECLARE_MSM_GPIO_PINS(14);
> +DECLARE_MSM_GPIO_PINS(15);
> +DECLARE_MSM_GPIO_PINS(16);
> +DECLARE_MSM_GPIO_PINS(17);
> +DECLARE_MSM_GPIO_PINS(18);
> +DECLARE_MSM_GPIO_PINS(19);
> +DECLARE_MSM_GPIO_PINS(20);
> +DECLARE_MSM_GPIO_PINS(21);
> +DECLARE_MSM_GPIO_PINS(22);
> +DECLARE_MSM_GPIO_PINS(23);
> +DECLARE_MSM_GPIO_PINS(24);
> +DECLARE_MSM_GPIO_PINS(25);
> +DECLARE_MSM_GPIO_PINS(26);
> +DECLARE_MSM_GPIO_PINS(27);
> +DECLARE_MSM_GPIO_PINS(28);
> +DECLARE_MSM_GPIO_PINS(29);
> +DECLARE_MSM_GPIO_PINS(30);
> +DECLARE_MSM_GPIO_PINS(31);
> +DECLARE_MSM_GPIO_PINS(32);
> +DECLARE_MSM_GPIO_PINS(33);
> +DECLARE_MSM_GPIO_PINS(34);
> +DECLARE_MSM_GPIO_PINS(35);
> +DECLARE_MSM_GPIO_PINS(36);
> +DECLARE_MSM_GPIO_PINS(37);
> +DECLARE_MSM_GPIO_PINS(38);
> +DECLARE_MSM_GPIO_PINS(39);
> +DECLARE_MSM_GPIO_PINS(40);
> +DECLARE_MSM_GPIO_PINS(41);
> +DECLARE_MSM_GPIO_PINS(42);
> +DECLARE_MSM_GPIO_PINS(43);
> +DECLARE_MSM_GPIO_PINS(44);
> +DECLARE_MSM_GPIO_PINS(45);
> +DECLARE_MSM_GPIO_PINS(46);
> +DECLARE_MSM_GPIO_PINS(47);
> +DECLARE_MSM_GPIO_PINS(48);
> +DECLARE_MSM_GPIO_PINS(49);
> +DECLARE_MSM_GPIO_PINS(50);
> +DECLARE_MSM_GPIO_PINS(51);
> +DECLARE_MSM_GPIO_PINS(52);
> +DECLARE_MSM_GPIO_PINS(53);
> +DECLARE_MSM_GPIO_PINS(54);
> +DECLARE_MSM_GPIO_PINS(55);
> +DECLARE_MSM_GPIO_PINS(56);
> +DECLARE_MSM_GPIO_PINS(57);
> +DECLARE_MSM_GPIO_PINS(58);
> +DECLARE_MSM_GPIO_PINS(59);
> +DECLARE_MSM_GPIO_PINS(60);
> +DECLARE_MSM_GPIO_PINS(61);
> +DECLARE_MSM_GPIO_PINS(62);
> +DECLARE_MSM_GPIO_PINS(63);
> +DECLARE_MSM_GPIO_PINS(64);
> +DECLARE_MSM_GPIO_PINS(65);
> +DECLARE_MSM_GPIO_PINS(66);
> +DECLARE_MSM_GPIO_PINS(67);
> +DECLARE_MSM_GPIO_PINS(68);
> +DECLARE_MSM_GPIO_PINS(69);
> +DECLARE_MSM_GPIO_PINS(70);
> +DECLARE_MSM_GPIO_PINS(71);
> +DECLARE_MSM_GPIO_PINS(72);
> +DECLARE_MSM_GPIO_PINS(73);
> +DECLARE_MSM_GPIO_PINS(74);
> +DECLARE_MSM_GPIO_PINS(75);
> +DECLARE_MSM_GPIO_PINS(76);
> +DECLARE_MSM_GPIO_PINS(77);
> +DECLARE_MSM_GPIO_PINS(78);
> +DECLARE_MSM_GPIO_PINS(79);
> +
> +enum ipq6018_functions {
> + msm_mux_atest_char,
> + msm_mux_atest_char0,
> + msm_mux_atest_char1,
> + msm_mux_atest_char2,
> + msm_mux_atest_char3,
> + msm_mux_audio0,
> + msm_mux_audio1,
> + msm_mux_audio2,
> + msm_mux_audio3,
> + msm_mux_audio_rxbclk,
> + msm_mux_audio_rxfsync,
> + msm_mux_audio_rxmclk,
> + msm_mux_audio_rxmclkin,
> + msm_mux_audio_txbclk,
> + msm_mux_audio_txfsync,
> + msm_mux_audio_txmclk,
> + msm_mux_audio_txmclkin,
> + msm_mux_blsp0_i2c,
> + msm_mux_blsp0_spi,
> + msm_mux_blsp0_uart,
> + msm_mux_blsp1_i2c,
> + msm_mux_blsp1_spi,
> + msm_mux_blsp1_uart,
> + msm_mux_blsp2_i2c,
> + msm_mux_blsp2_spi,
> + msm_mux_blsp2_uart,
> + msm_mux_blsp3_i2c,
> + msm_mux_blsp3_spi,
> + msm_mux_blsp3_uart,
> + msm_mux_blsp4_i2c,
> + msm_mux_blsp4_spi,
> + msm_mux_blsp4_uart,
> + msm_mux_blsp5_i2c,
> + msm_mux_blsp5_uart,
> + msm_mux_burn0,
> + msm_mux_burn1,
> + msm_mux_cri_trng,
> + msm_mux_cri_trng0,
> + msm_mux_cri_trng1,
> + msm_mux_cxc0,
> + msm_mux_cxc1,
> + msm_mux_dbg_out,
> + msm_mux_gcc_plltest,
> + msm_mux_gcc_tlmm,
> + msm_mux_gpio,
> + msm_mux_lpass_aud,
> + msm_mux_lpass_aud0,
> + msm_mux_lpass_aud1,
> + msm_mux_lpass_aud2,
> + msm_mux_lpass_pcm,
> + msm_mux_lpass_pdm,
> + msm_mux_mac00,
> + msm_mux_mac01,
> + msm_mux_mac10,
> + msm_mux_mac11,
> + msm_mux_mac12,
> + msm_mux_mac13,
> + msm_mux_mac20,
> + msm_mux_mac21,
> + msm_mux_mdc,
> + msm_mux_mdio,
> + msm_mux_pcie0_clk,
> + msm_mux_pcie0_rst,
> + msm_mux_pcie0_wake,
> + msm_mux_prng_rosc,
> + msm_mux_pta1_0,
> + msm_mux_pta1_1,
> + msm_mux_pta1_2,
> + msm_mux_pta2_0,
> + msm_mux_pta2_1,
> + msm_mux_pta2_2,
> + msm_mux_pwm00,
> + msm_mux_pwm01,
> + msm_mux_pwm02,
> + msm_mux_pwm03,
> + msm_mux_pwm04,
> + msm_mux_pwm10,
> + msm_mux_pwm11,
> + msm_mux_pwm12,
> + msm_mux_pwm13,
> + msm_mux_pwm14,
> + msm_mux_pwm20,
> + msm_mux_pwm21,
> + msm_mux_pwm22,
> + msm_mux_pwm23,
> + msm_mux_pwm24,
> + msm_mux_pwm30,
> + msm_mux_pwm31,
> + msm_mux_pwm32,
> + msm_mux_pwm33,
> + msm_mux_qdss_cti_trig_in_a0,
> + msm_mux_qdss_cti_trig_in_a1,
> + msm_mux_qdss_cti_trig_out_a0,
> + msm_mux_qdss_cti_trig_out_a1,
> + msm_mux_qdss_cti_trig_in_b0,
> + msm_mux_qdss_cti_trig_in_b1,
> + msm_mux_qdss_cti_trig_out_b0,
> + msm_mux_qdss_cti_trig_out_b1,
> + msm_mux_qdss_traceclk_a,
> + msm_mux_qdss_tracectl_a,
> + msm_mux_qdss_tracedata_a,
> + msm_mux_qdss_traceclk_b,
> + msm_mux_qdss_tracectl_b,
> + msm_mux_qdss_tracedata_b,
> + msm_mux_qpic_pad,
> + msm_mux_rx0,
> + msm_mux_rx1,
> + msm_mux_rx_swrm,
> + msm_mux_rx_swrm0,
> + msm_mux_rx_swrm1,
> + msm_mux_sd_card,
> + msm_mux_sd_write,
> + msm_mux_tsens_max,
> + msm_mux_tx_swrm,
> + msm_mux_tx_swrm0,
> + msm_mux_tx_swrm1,
> + msm_mux_tx_swrm2,
> + msm_mux_wci20,
> + msm_mux_wci21,
> + msm_mux_wci22,
> + msm_mux_wci23,
> + msm_mux_wsa_swrm,
> + msm_mux__,
> +};
> +
> +static const char * const blsp3_uart_groups[] = {
> + "gpio73", "gpio74", "gpio75", "gpio76",
> +};
> +
> +static const char * const blsp3_i2c_groups[] = {
> + "gpio73", "gpio74",
> +};
> +
> +static const char * const blsp3_spi_groups[] = {
> + "gpio73", "gpio74", "gpio75", "gpio76", "gpio77", "gpio78", "gpio79",
> +};
> +
> +static const char * const wci20_groups[] = {
> + "gpio0", "gpio2",
> +};
> +
> +static const char * const qpic_pad_groups[] = {
> + "gpio0", "gpio1", "gpio2", "gpio3", "gpio4", "gpio9", "gpio10",
> + "gpio11", "gpio17",
> +};
> +
> +static const char * const burn0_groups[] = {
> + "gpio0",
> +};
> +
> +static const char * const mac12_groups[] = {
> + "gpio1", "gpio11",
> +};
> +
> +static const char * const qdss_tracectl_b_groups[] = {
> + "gpio1",
> +};
> +
> +static const char * const burn1_groups[] = {
> + "gpio1",
> +};
> +
> +static const char * const qdss_traceclk_b_groups[] = {
> + "gpio0",
> +};
> +
> +static const char * const qdss_tracedata_b_groups[] = {
> + "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7", "gpio8", "gpio9",
> + "gpio10", "gpio11", "gpio12", "gpio13", "gpio14", "gpio15", "gpio16",
> + "gpio17",
> +};
> +
> +static const char * const mac01_groups[] = {
> + "gpio3", "gpio4",
> +};
> +
> +static const char * const mac21_groups[] = {
> + "gpio5", "gpio6",
> +};
> +
> +static const char * const atest_char_groups[] = {
> + "gpio9",
> +};
> +
> +static const char * const cxc0_groups[] = {
> + "gpio9", "gpio16",
> +};
> +
> +static const char * const mac13_groups[] = {
> + "gpio9", "gpio16",
> +};
> +
> +static const char * const dbg_out_groups[] = {
> + "gpio9",
> +};
> +
> +static const char * const wci22_groups[] = {
> + "gpio11", "gpio17",
> +};
> +
> +static const char * const pwm00_groups[] = {
> + "gpio18",
> +};
> +
> +static const char * const atest_char0_groups[] = {
> + "gpio18",
> +};
> +
> +static const char * const wci23_groups[] = {
> + "gpio18", "gpio19",
> +};
> +
> +static const char * const mac11_groups[] = {
> + "gpio18", "gpio19",
> +};
> +
> +static const char * const pwm10_groups[] = {
> + "gpio19",
> +};
> +
> +static const char * const atest_char1_groups[] = {
> + "gpio19",
> +};
> +
> +static const char * const pwm20_groups[] = {
> + "gpio20",
> +};
> +
> +static const char * const atest_char2_groups[] = {
> + "gpio20",
> +};
> +
> +static const char * const pwm30_groups[] = {
> + "gpio21",
> +};
> +
> +static const char * const atest_char3_groups[] = {
> + "gpio21",
> +};
> +
> +static const char * const audio_txmclk_groups[] = {
> + "gpio22",
> +};
> +
> +static const char * const audio_txmclkin_groups[] = {
> + "gpio22",
> +};
> +
> +static const char * const pwm02_groups[] = {
> + "gpio22",
> +};
> +
> +static const char * const tx_swrm0_groups[] = {
> + "gpio22",
> +};
> +
> +static const char * const qdss_cti_trig_out_b0_groups[] = {
> + "gpio22",
> +};
> +
> +static const char * const audio_txbclk_groups[] = {
> + "gpio23",
> +};
> +
> +static const char * const pwm12_groups[] = {
> + "gpio23",
> +};
> +
> +static const char * const wsa_swrm_groups[] = {
> + "gpio23", "gpio24",
> +};
> +
> +static const char * const tx_swrm1_groups[] = {
> + "gpio23",
> +};
> +
> +static const char * const qdss_cti_trig_in_b0_groups[] = {
> + "gpio23",
> +};
> +
> +static const char * const audio_txfsync_groups[] = {
> + "gpio24",
> +};
> +
> +static const char * const pwm22_groups[] = {
> + "gpio24",
> +};
> +
> +static const char * const tx_swrm2_groups[] = {
> + "gpio24",
> +};
> +
> +static const char * const qdss_cti_trig_out_b1_groups[] = {
> + "gpio24",
> +};
> +
> +static const char * const audio0_groups[] = {
> + "gpio25", "gpio32",
> +};
> +
> +static const char * const pwm32_groups[] = {
> + "gpio25",
> +};
> +
> +static const char * const tx_swrm_groups[] = {
> + "gpio25",
> +};
> +
> +static const char * const qdss_cti_trig_in_b1_groups[] = {
> + "gpio25",
> +};
> +
> +static const char * const audio1_groups[] = {
> + "gpio26", "gpio33",
> +};
> +
> +static const char * const pwm04_groups[] = {
> + "gpio26",
> +};
> +
> +static const char * const audio2_groups[] = {
> + "gpio27",
> +};
> +
> +static const char * const pwm14_groups[] = {
> + "gpio27",
> +};
> +
> +static const char * const audio3_groups[] = {
> + "gpio28",
> +};
> +
> +static const char * const pwm24_groups[] = {
> + "gpio28",
> +};
> +
> +static const char * const audio_rxmclk_groups[] = {
> + "gpio29",
> +};
> +
> +static const char * const audio_rxmclkin_groups[] = {
> + "gpio29",
> +};
> +
> +static const char * const pwm03_groups[] = {
> + "gpio29",
> +};
> +
> +static const char * const lpass_pdm_groups[] = {
> + "gpio29", "gpio30", "gpio31", "gpio32",
> +};
> +
> +static const char * const lpass_aud_groups[] = {
> + "gpio29",
> +};
> +
> +static const char * const qdss_cti_trig_in_a1_groups[] = {
> + "gpio29",
> +};
> +
> +static const char * const audio_rxbclk_groups[] = {
> + "gpio30",
> +};
> +
> +static const char * const pwm13_groups[] = {
> + "gpio30",
> +};
> +
> +static const char * const lpass_aud0_groups[] = {
> + "gpio30",
> +};
> +
> +static const char * const rx_swrm_groups[] = {
> + "gpio30",
> +};
> +
> +static const char * const qdss_cti_trig_out_a1_groups[] = {
> + "gpio30",
> +};
> +
> +static const char * const audio_rxfsync_groups[] = {
> + "gpio31",
> +};
> +
> +static const char * const pwm23_groups[] = {
> + "gpio31",
> +};
> +
> +static const char * const lpass_aud1_groups[] = {
> + "gpio31",
> +};
> +
> +static const char * const rx_swrm0_groups[] = {
> + "gpio31",
> +};
> +
> +static const char * const qdss_cti_trig_in_a0_groups[] = {
> + "gpio31",
> +};
> +
> +static const char * const pwm33_groups[] = {
> + "gpio32",
> +};
> +
> +static const char * const lpass_aud2_groups[] = {
> + "gpio32",
> +};
> +
> +static const char * const rx_swrm1_groups[] = {
> + "gpio32",
> +};
> +
> +static const char * const qdss_cti_trig_out_a0_groups[] = {
> + "gpio32",
> +};
> +
> +static const char * const lpass_pcm_groups[] = {
> + "gpio34", "gpio35", "gpio36", "gpio37",
> +};
> +
> +static const char * const mac10_groups[] = {
> + "gpio34", "gpio35",
> +};
> +
> +static const char * const mac00_groups[] = {
> + "gpio34", "gpio35",
> +};
> +
> +static const char * const mac20_groups[] = {
> + "gpio36", "gpio37",
> +};
> +
> +static const char * const blsp0_uart_groups[] = {
> + "gpio38", "gpio39", "gpio40", "gpio41",
> +};
> +
> +static const char * const blsp0_i2c_groups[] = {
> + "gpio38", "gpio39",
> +};
> +
> +static const char * const blsp0_spi_groups[] = {
> + "gpio38", "gpio39", "gpio40", "gpio41",
> +};
> +
> +static const char * const blsp2_uart_groups[] = {
> + "gpio42", "gpio43", "gpio44", "gpio45",
> +};
> +
> +static const char * const blsp2_i2c_groups[] = {
> + "gpio42", "gpio43",
> +};
> +
> +static const char * const blsp2_spi_groups[] = {
> + "gpio42", "gpio43", "gpio44", "gpio45",
> +};
> +
> +static const char * const blsp5_i2c_groups[] = {
> + "gpio46", "gpio47",
> +};
> +
> +static const char * const blsp5_uart_groups[] = {
> + "gpio48", "gpio49",
> +};
> +
> +static const char * const qdss_traceclk_a_groups[] = {
> + "gpio48",
> +};
> +
> +static const char * const qdss_tracectl_a_groups[] = {
> + "gpio49",
> +};
> +
> +static const char * const pwm01_groups[] = {
> + "gpio50",
> +};
> +
> +static const char * const pta1_1_groups[] = {
> + "gpio51",
> +};
> +
> +static const char * const pwm11_groups[] = {
> + "gpio51",
> +};
> +
> +static const char * const rx1_groups[] = {
> + "gpio51",
> +};
> +
> +static const char * const pta1_2_groups[] = {
> + "gpio52",
> +};
> +
> +static const char * const pwm21_groups[] = {
> + "gpio52",
> +};
> +
> +static const char * const pta1_0_groups[] = {
> + "gpio53",
> +};
> +
> +static const char * const pwm31_groups[] = {
> + "gpio53",
> +};
> +
> +static const char * const prng_rosc_groups[] = {
> + "gpio53",
> +};
> +
> +static const char * const blsp4_uart_groups[] = {
> + "gpio55", "gpio56", "gpio57", "gpio58",
> +};
> +
> +static const char * const blsp4_i2c_groups[] = {
> + "gpio55", "gpio56",
> +};
> +
> +static const char * const blsp4_spi_groups[] = {
> + "gpio55", "gpio56", "gpio57", "gpio58",
> +};
> +
> +static const char * const pcie0_clk_groups[] = {
> + "gpio59",
> +};
> +
> +static const char * const cri_trng0_groups[] = {
> + "gpio59",
> +};
> +
> +static const char * const pcie0_rst_groups[] = {
> + "gpio60",
> +};
> +
> +static const char * const cri_trng1_groups[] = {
> + "gpio60",
> +};
> +
> +static const char * const pcie0_wake_groups[] = {
> + "gpio61",
> +};
> +
> +static const char * const cri_trng_groups[] = {
> + "gpio61",
> +};
> +
> +static const char * const sd_card_groups[] = {
> + "gpio62",
> +};
> +
> +static const char * const sd_write_groups[] = {
> + "gpio63",
> +};
> +
> +static const char * const rx0_groups[] = {
> + "gpio63",
> +};
> +
> +static const char * const tsens_max_groups[] = {
> + "gpio63",
> +};
> +
> +static const char * const mdc_groups[] = {
> + "gpio64",
> +};
> +
> +static const char * const qdss_tracedata_a_groups[] = {
> + "gpio64", "gpio65", "gpio66", "gpio67", "gpio68", "gpio69", "gpio70",
> + "gpio71", "gpio72", "gpio73", "gpio74", "gpio75", "gpio76", "gpio77",
> + "gpio78", "gpio79",
> +};
> +
> +static const char * const mdio_groups[] = {
> + "gpio65",
> +};
> +
> +static const char * const pta2_0_groups[] = {
> + "gpio66",
> +};
> +
> +static const char * const wci21_groups[] = {
> + "gpio66", "gpio68",
> +};
> +
> +static const char * const cxc1_groups[] = {
> + "gpio66", "gpio68",
> +};
> +
> +static const char * const pta2_1_groups[] = {
> + "gpio67",
> +};
> +
> +static const char * const pta2_2_groups[] = {
> + "gpio68",
> +};
> +
> +static const char * const blsp1_uart_groups[] = {
> + "gpio69", "gpio70", "gpio71", "gpio72",
> +};
> +
> +static const char * const blsp1_i2c_groups[] = {
> + "gpio69", "gpio70",
> +};
> +
> +static const char * const blsp1_spi_groups[] = {
> + "gpio69", "gpio70", "gpio71", "gpio72",
> +};
> +
> +static const char * const gcc_plltest_groups[] = {
> + "gpio69", "gpio71",
> +};
> +
> +static const char * const gcc_tlmm_groups[] = {
> + "gpio70",
> +};
> +
> +static const char * const gpio_groups[] = {
> + "gpio0", "gpio1", "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7",
> + "gpio8", "gpio9", "gpio10", "gpio11", "gpio12", "gpio13", "gpio14",
> + "gpio15", "gpio16", "gpio17", "gpio18", "gpio19", "gpio20", "gpio21",
> + "gpio22", "gpio23", "gpio24", "gpio25", "gpio26", "gpio27", "gpio28",
> + "gpio29", "gpio30", "gpio31", "gpio32", "gpio33", "gpio34", "gpio35",
> + "gpio36", "gpio37", "gpio38", "gpio39", "gpio40", "gpio41", "gpio42",
> + "gpio43", "gpio44", "gpio45", "gpio46", "gpio47", "gpio48", "gpio49",
> + "gpio50", "gpio51", "gpio52", "gpio53", "gpio54", "gpio55", "gpio56",
> + "gpio57", "gpio58", "gpio59", "gpio60", "gpio61", "gpio62", "gpio63",
> + "gpio64", "gpio65", "gpio66", "gpio67", "gpio68", "gpio69", "gpio70",
> + "gpio71", "gpio72", "gpio73", "gpio74", "gpio75", "gpio76", "gpio77",
> + "gpio78", "gpio79",
> +};
> +
> +static const struct msm_function ipq6018_functions[] = {
> + FUNCTION(atest_char),
> + FUNCTION(atest_char0),
> + FUNCTION(atest_char1),
> + FUNCTION(atest_char2),
> + FUNCTION(atest_char3),
> + FUNCTION(audio0),
> + FUNCTION(audio1),
> + FUNCTION(audio2),
> + FUNCTION(audio3),
> + FUNCTION(audio_rxbclk),
> + FUNCTION(audio_rxfsync),
> + FUNCTION(audio_rxmclk),
> + FUNCTION(audio_rxmclkin),
> + FUNCTION(audio_txbclk),
> + FUNCTION(audio_txfsync),
> + FUNCTION(audio_txmclk),
> + FUNCTION(audio_txmclkin),
> + FUNCTION(blsp0_i2c),
> + FUNCTION(blsp0_spi),
> + FUNCTION(blsp0_uart),
> + FUNCTION(blsp1_i2c),
> + FUNCTION(blsp1_spi),
> + FUNCTION(blsp1_uart),
> + FUNCTION(blsp2_i2c),
> + FUNCTION(blsp2_spi),
> + FUNCTION(blsp2_uart),
> + FUNCTION(blsp3_i2c),
> + FUNCTION(blsp3_spi),
> + FUNCTION(blsp3_uart),
> + FUNCTION(blsp4_i2c),
> + FUNCTION(blsp4_spi),
> + FUNCTION(blsp4_uart),
> + FUNCTION(blsp5_i2c),
> + FUNCTION(blsp5_uart),
> + FUNCTION(burn0),
> + FUNCTION(burn1),
> + FUNCTION(cri_trng),
> + FUNCTION(cri_trng0),
> + FUNCTION(cri_trng1),
> + FUNCTION(cxc0),
> + FUNCTION(cxc1),
> + FUNCTION(dbg_out),
> + FUNCTION(gcc_plltest),
> + FUNCTION(gcc_tlmm),
> + FUNCTION(gpio),
> + FUNCTION(lpass_aud),
> + FUNCTION(lpass_aud0),
> + FUNCTION(lpass_aud1),
> + FUNCTION(lpass_aud2),
> + FUNCTION(lpass_pcm),
> + FUNCTION(lpass_pdm),
> + FUNCTION(mac00),
> + FUNCTION(mac01),
> + FUNCTION(mac10),
> + FUNCTION(mac11),
> + FUNCTION(mac12),
> + FUNCTION(mac13),
> + FUNCTION(mac20),
> + FUNCTION(mac21),
> + FUNCTION(mdc),
> + FUNCTION(mdio),
> + FUNCTION(pcie0_clk),
> + FUNCTION(pcie0_rst),
> + FUNCTION(pcie0_wake),
> + FUNCTION(prng_rosc),
> + FUNCTION(pta1_0),
> + FUNCTION(pta1_1),
> + FUNCTION(pta1_2),
> + FUNCTION(pta2_0),
> + FUNCTION(pta2_1),
> + FUNCTION(pta2_2),
> + FUNCTION(pwm00),
> + FUNCTION(pwm01),
> + FUNCTION(pwm02),
> + FUNCTION(pwm03),
> + FUNCTION(pwm04),
> + FUNCTION(pwm10),
> + FUNCTION(pwm11),
> + FUNCTION(pwm12),
> + FUNCTION(pwm13),
> + FUNCTION(pwm14),
> + FUNCTION(pwm20),
> + FUNCTION(pwm21),
> + FUNCTION(pwm22),
> + FUNCTION(pwm23),
> + FUNCTION(pwm24),
> + FUNCTION(pwm30),
> + FUNCTION(pwm31),
> + FUNCTION(pwm32),
> + FUNCTION(pwm33),
> + FUNCTION(qdss_cti_trig_in_a0),
> + FUNCTION(qdss_cti_trig_in_a1),
> + FUNCTION(qdss_cti_trig_out_a0),
> + FUNCTION(qdss_cti_trig_out_a1),
> + FUNCTION(qdss_cti_trig_in_b0),
> + FUNCTION(qdss_cti_trig_in_b1),
> + FUNCTION(qdss_cti_trig_out_b0),
> + FUNCTION(qdss_cti_trig_out_b1),
> + FUNCTION(qdss_traceclk_a),
> + FUNCTION(qdss_tracectl_a),
> + FUNCTION(qdss_tracedata_a),
> + FUNCTION(qdss_traceclk_b),
> + FUNCTION(qdss_tracectl_b),
> + FUNCTION(qdss_tracedata_b),
> + FUNCTION(qpic_pad),
> + FUNCTION(rx0),
> + FUNCTION(rx1),
> + FUNCTION(rx_swrm),
> + FUNCTION(rx_swrm0),
> + FUNCTION(rx_swrm1),
> + FUNCTION(sd_card),
> + FUNCTION(sd_write),
> + FUNCTION(tsens_max),
> + FUNCTION(tx_swrm),
> + FUNCTION(tx_swrm0),
> + FUNCTION(tx_swrm1),
> + FUNCTION(tx_swrm2),
> + FUNCTION(wci20),
> + FUNCTION(wci21),
> + FUNCTION(wci22),
> + FUNCTION(wci23),
> + FUNCTION(wsa_swrm),
> +};
> +
> +static const struct msm_pingroup ipq6018_groups[] = {
> + PINGROUP(0, qpic_pad, wci20, qdss_traceclk_b, _, burn0, _, _, _, _),
> + PINGROUP(1, qpic_pad, mac12, qdss_tracectl_b, _, burn1, _, _, _, _),
> + PINGROUP(2, qpic_pad, wci20, qdss_tracedata_b, _, _, _, _, _, _),
> + PINGROUP(3, qpic_pad, mac01, qdss_tracedata_b, _, _, _, _, _, _),
> + PINGROUP(4, qpic_pad, mac01, qdss_tracedata_b, _, _, _, _, _, _),
> + PINGROUP(5, qpic_pad, mac21, qdss_tracedata_b, _, _, _, _, _, _),
> + PINGROUP(6, qpic_pad, mac21, qdss_tracedata_b, _, _, _, _, _, _),
> + PINGROUP(7, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
> + PINGROUP(8, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
> + PINGROUP(9, qpic_pad, atest_char, cxc0, mac13, dbg_out, qdss_tracedata_b, _, _, _),
> + PINGROUP(10, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
> + PINGROUP(11, qpic_pad, wci22, mac12, qdss_tracedata_b, _, _, _, _, _),
> + PINGROUP(12, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
> + PINGROUP(13, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
> + PINGROUP(14, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
> + PINGROUP(15, qpic_pad, qdss_tracedata_b, _, _, _, _, _, _, _),
> + PINGROUP(16, qpic_pad, cxc0, mac13, qdss_tracedata_b, _, _, _, _, _),
> + PINGROUP(17, qpic_pad, qdss_tracedata_b, wci22, _, _, _, _, _, _),
> + PINGROUP(18, pwm00, atest_char0, wci23, mac11, _, _, _, _, _),
> + PINGROUP(19, pwm10, atest_char1, wci23, mac11, _, _, _, _, _),
> + PINGROUP(20, pwm20, atest_char2, _, _, _, _, _, _, _),
> + PINGROUP(21, pwm30, atest_char3, _, _, _, _, _, _, _),
> + PINGROUP(22, audio_txmclk, audio_txmclkin, pwm02, tx_swrm0, _, qdss_cti_trig_out_b0, _, _, _),
> + PINGROUP(23, audio_txbclk, pwm12, wsa_swrm, tx_swrm1, _, qdss_cti_trig_in_b0, _, _, _),
> + PINGROUP(24, audio_txfsync, pwm22, wsa_swrm, tx_swrm2, _, qdss_cti_trig_out_b1, _, _, _),
> + PINGROUP(25, audio0, pwm32, tx_swrm, _, qdss_cti_trig_in_b1, _, _, _, _),
> + PINGROUP(26, audio1, pwm04, _, _, _, _, _, _, _),
> + PINGROUP(27, audio2, pwm14, _, _, _, _, _, _, _),
> + PINGROUP(28, audio3, pwm24, _, _, _, _, _, _, _),
> + PINGROUP(29, audio_rxmclk, audio_rxmclkin, pwm03, lpass_pdm, lpass_aud, qdss_cti_trig_in_a1, _, _, _),
> + PINGROUP(30, audio_rxbclk, pwm13, lpass_pdm, lpass_aud0, rx_swrm, _, qdss_cti_trig_out_a1, _, _),
> + PINGROUP(31, audio_rxfsync, pwm23, lpass_pdm, lpass_aud1, rx_swrm0, _, qdss_cti_trig_in_a0, _, _),
> + PINGROUP(32, audio0, pwm33, lpass_pdm, lpass_aud2, rx_swrm1, _, qdss_cti_trig_out_a0, _, _),
> + PINGROUP(33, audio1, _, _, _, _, _, _, _, _),
> + PINGROUP(34, lpass_pcm, mac10, mac00, _, _, _, _, _, _),
> + PINGROUP(35, lpass_pcm, mac10, mac00, _, _, _, _, _, _),
> + PINGROUP(36, lpass_pcm, mac20, _, _, _, _, _, _, _),
> + PINGROUP(37, lpass_pcm, mac20, _, _, _, _, _, _, _),
> + PINGROUP(38, blsp0_uart, blsp0_i2c, blsp0_spi, _, _, _, _, _, _),
> + PINGROUP(39, blsp0_uart, blsp0_i2c, blsp0_spi, _, _, _, _, _, _),
> + PINGROUP(40, blsp0_uart, blsp0_spi, _, _, _, _, _, _, _),
> + PINGROUP(41, blsp0_uart, blsp0_spi, _, _, _, _, _, _, _),
> + PINGROUP(42, blsp2_uart, blsp2_i2c, blsp2_spi, _, _, _, _, _, _),
> + PINGROUP(43, blsp2_uart, blsp2_i2c, blsp2_spi, _, _, _, _, _, _),
> + PINGROUP(44, blsp2_uart, blsp2_spi, _, _, _, _, _, _, _),
> + PINGROUP(45, blsp2_uart, blsp2_spi, _, _, _, _, _, _, _),
> + PINGROUP(46, blsp5_i2c, _, _, _, _, _, _, _, _),
> + PINGROUP(47, blsp5_i2c, _, _, _, _, _, _, _, _),
> + PINGROUP(48, blsp5_uart, _, qdss_traceclk_a, _, _, _, _, _, _),
> + PINGROUP(49, blsp5_uart, _, qdss_tracectl_a, _, _, _, _, _, _),
> + PINGROUP(50, pwm01, _, _, _, _, _, _, _, _),
> + PINGROUP(51, pta1_1, pwm11, _, rx1, _, _, _, _, _),
> + PINGROUP(52, pta1_2, pwm21, _, _, _, _, _, _, _),
> + PINGROUP(53, pta1_0, pwm31, prng_rosc, _, _, _, _, _, _),
> + PINGROUP(54, _, _, _, _, _, _, _, _, _),
> + PINGROUP(55, blsp4_uart, blsp4_i2c, blsp4_spi, _, _, _, _, _, _),
> + PINGROUP(56, blsp4_uart, blsp4_i2c, blsp4_spi, _, _, _, _, _, _),
> + PINGROUP(57, blsp4_uart, blsp4_spi, _, _, _, _, _, _, _),
> + PINGROUP(58, blsp4_uart, blsp4_spi, _, _, _, _, _, _, _),
> + PINGROUP(59, pcie0_clk, _, _, cri_trng0, _, _, _, _, _),
> + PINGROUP(60, pcie0_rst, _, _, cri_trng1, _, _, _, _, _),
> + PINGROUP(61, pcie0_wake, _, _, cri_trng, _, _, _, _, _),
> + PINGROUP(62, sd_card, _, _, _, _, _, _, _, _),
> + PINGROUP(63, sd_write, rx0, _, tsens_max, _, _, _, _, _),
> + PINGROUP(64, mdc, _, qdss_tracedata_a, _, _, _, _, _, _),
> + PINGROUP(65, mdio, _, qdss_tracedata_a, _, _, _, _, _, _),
> + PINGROUP(66, pta2_0, wci21, cxc1, qdss_tracedata_a, _, _, _, _, _),
> + PINGROUP(67, pta2_1, qdss_tracedata_a, _, _, _, _, _, _, _),
> + PINGROUP(68, pta2_2, wci21, cxc1, qdss_tracedata_a, _, _, _, _, _),
> + PINGROUP(69, blsp1_uart, blsp1_i2c, blsp1_spi, gcc_plltest, qdss_tracedata_a, _, _, _, _),
> + PINGROUP(70, blsp1_uart, blsp1_i2c, blsp1_spi, gcc_tlmm, qdss_tracedata_a, _, _, _, _),
> + PINGROUP(71, blsp1_uart, blsp1_spi, gcc_plltest, qdss_tracedata_a, _, _, _, _, _),
> + PINGROUP(72, blsp1_uart, blsp1_spi, qdss_tracedata_a, _, _, _, _, _, _),
> + PINGROUP(73, blsp3_uart, blsp3_i2c, blsp3_spi, _, qdss_tracedata_a, _, _, _, _),
> + PINGROUP(74, blsp3_uart, blsp3_i2c, blsp3_spi, _, qdss_tracedata_a, _, _, _, _),
> + PINGROUP(75, blsp3_uart, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _),
> + PINGROUP(76, blsp3_uart, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _),
> + PINGROUP(77, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _, _),
> + PINGROUP(78, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _, _),
> + PINGROUP(79, blsp3_spi, _, qdss_tracedata_a, _, _, _, _, _, _),
> +};
> +
> +static const struct msm_pinctrl_soc_data ipq6018_pinctrl = {
> + .pins = ipq6018_pins,
> + .npins = ARRAY_SIZE(ipq6018_pins),
> + .functions = ipq6018_functions,
> + .nfunctions = ARRAY_SIZE(ipq6018_functions),
> + .groups = ipq6018_groups,
> + .ngroups = ARRAY_SIZE(ipq6018_groups),
> + .ngpios = 80,
> +};
> +
> +static int ipq6018_pinctrl_probe(struct platform_device *pdev)
> +{
> + return msm_pinctrl_probe(pdev, &ipq6018_pinctrl);
> +}
> +
> +static const struct of_device_id ipq6018_pinctrl_of_match[] = {
> + { .compatible = "qcom,ipq6018-pinctrl", },
> + { },
> +};
> +
> +static struct platform_driver ipq6018_pinctrl_driver = {
> + .driver = {
> + .name = "ipq6018-pinctrl",
> + .of_match_table = ipq6018_pinctrl_of_match,
> + },
> + .probe = ipq6018_pinctrl_probe,
> + .remove = msm_pinctrl_remove,
> +};
> +
> +static int __init ipq6018_pinctrl_init(void)
> +{
> + return platform_driver_register(&ipq6018_pinctrl_driver);
> +}
> +arch_initcall(ipq6018_pinctrl_init);
> +
> +static void __exit ipq6018_pinctrl_exit(void)
> +{
> + platform_driver_unregister(&ipq6018_pinctrl_driver);
> +}
> +module_exit(ipq6018_pinctrl_exit);
> +
> +MODULE_DESCRIPTION("QTI ipq6018 pinctrl driver");
> +MODULE_LICENSE("GPL v2");
> +MODULE_DEVICE_TABLE(of, ipq6018_pinctrl_of_match);
> --
> 1.9.1
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH V3 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings
2020-01-04 0:58 ` Rob Herring
@ 2020-01-06 5:25 ` Sricharan R
0 siblings, 0 replies; 12+ messages in thread
From: Sricharan R @ 2020-01-06 5:25 UTC (permalink / raw)
To: Rob Herring
Cc: devicetree, sboyd, linux-arm-msm, linus.walleij, linux-kernel,
linux-gpio, agross, sivaprak, linux-soc, linux-clk,
linux-arm-kernel
Hi Rob,
Thanks for the review.
On 1/4/2020 6:28 AM, Rob Herring wrote:
> On Fri, Jan 03, 2020 at 05:19:33PM +0530, Sricharan R wrote:
>> Add device tree binding Documentation details for ipq6018
>> pinctrl driver.
>>
>> Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
>> Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
>> Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
>> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
>> Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
>> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
>> Signed-off-by: Sricharan R <sricharan@codeaurora.org>
>> ---
>> [v3] Fixed the example dt node, inherited properties
>>
>> .../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml | 166 +++++++++++++++++++++
>> 1 file changed, 166 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
>> new file mode 100644
>> index 0000000..e959c5f
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
>> @@ -0,0 +1,166 @@
>> +# SPDX-License-Identifier: GPL-2.0-or-later
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/pinctrl/qcom,ipq6018-pinctrl.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Qualcomm Technologies, Inc. IPQ6018 TLMM block
>> +
>> +maintainers:
>> + - Sricharan R <sricharan@codeaurora.org>
>> +
>> +description: |
>> + This binding describes the Top Level Mode Multiplexer block found in the
>> + IPQ6018 platform.
>> +
>> +properties:
>> + compatible:
>> + const: qcom,ipq6018-pinctrl
>
> A blank line after each property schema is preferred.
ok.
>
>> + reg:
>> + maxItems: 1
>> + interrupts:
>> + Description: Specifies the TLMM summary IRQ
>> + maxItems: 1
>> + interrupt-controller: true
>> + '#interrupt-cells':
>> + Description:
>> + Specifies the PIN numbers and Flags, as defined in defined in
>> + include/dt-bindings/interrupt-controller/irq.h
>> + const: 2
>> + gpio-controller: true
>> + '#gpio-cells':
>> + Description: Specifying the pin number and flags, as defined in
>> + include/dt-bindings/gpio/gpio.h
>> + const: 2
>> + gpio-ranges:
>> + Description: Documentation/devicetree/bindings/gpio/gpio.txt
>> + maxItems: 1
>> +
>> +#PIN CONFIGURATION NODES
>> +patternProperties:
>> + '-pins$':
>> + type: object
>> + Description:
>> + Pinctrl node's client devices use subnodes for desired pin configuration.
>> + Client device subnodes use below standard properties.
>> +
>> + Properties:
>
> Did you run 'make dt_binding_check' and is dt-schema up to date? This
> isn't valid json-schema which is case sensitive.
ok, will run the checks and will fix it.
>
>> + pins:
>> + allOf:
>> + $ref: /schemas/types.yaml#/definitions/string
>
> Also not valid as allOf is a list.
>
ok, will fix
>> + enum:
>> + gpio0-gpio80
>
> As is 'enum'...
ok.
>
>> + sdc1_clk
>> + sdc1_cmd
>> + sdc1_data
>> + sdc2_clk
>> + sdc2_cmd
>> + sdc2_data
>> + qdsd_cmd
>> + qdsd_data0
>> + qdsd_data1
>> + qdsd_data2
>> + qdsd_data3
>> + Description:
>> + List of gpio pins affected by the properties specified in this
>> + subnode.
>> +
>> + function:
>> + allOf:
>> + $ref: /schemas/types.yaml#/definitions/string
>> + enum:
>> + adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char,
>> + atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac,
>> + atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0,
>> + atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp_i2c1,
>> + blsp_i2c2, blsp_i2c3, blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_spi1,
>> + blsp_spi1_cs1, blsp_spi1_cs2, blsp_spi1_cs3, blsp_spi2,
>> + blsp_spi2_cs1, blsp_spi2_cs2, blsp_spi2_cs3, blsp_spi3,
>> + blsp_spi3_cs1, blsp_spi3_cs2, blsp_spi3_cs3, blsp_spi4, blsp_spi5,
>> + blsp_spi6, blsp_uart1, blsp_uart2, blsp_uim1, blsp_uim2, cam1_rst,
>> + cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0,
>> + cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v,
>> + dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass,
>> + flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a,
>> + gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0,
>> + gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2,
>> + ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc,
>> + nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s,
>> + pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
>> + pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a,
>> + pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1,
>> + qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0,
>> + qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1,
>> + qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b,
>> + qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write,
>> + sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3,
>> + uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst
>> + Description:
>> + Specify the alternative function to be configured for the specified
>> + pins.
>> + bias-disable:
>> + allOf:
>> + $ref: /schemas/pinctrl/pincfg-node.yaml
>
> While you should have this reference, it is at the wrong level. The node
> needs to reference this schema, not the properties.
>
ok, will fix here and below properties as well.
Regards,
Sricharan
>> + Description:
>> + The specified pins should be configured as no pull.
>> + bias-pull-down:
>> + allOf:
>> + $ref: /schemas/pinctrl/pincfg-node.yaml
>> + Description:
>> + The specified pins should be configured as pull down.
>> + bias-pull-up:
>> + allOf:
>> + $ref: /schemas/pinctrl/pincfg-node.yaml
>> + Description:
>> + The specified pins should be configured as pull up.
>> + output-high:
>> + allOf:
>> + $ref: /schemas/pinctrl/pincfg-node.yaml
>> + Description:
>> + The specified pins are configured in output mode, driven high.
>> + This option is not available for sdc pins.
>> + output-low:
>> + allOf:
>> + $ref: /schemas/pinctrl/pincfg-node.yaml
>> + Description:
>> + The specified pins are configured in output mode, driven low.
>> + This option is not available for sdc pins.
>> + drive-strength:
>> + allOf:
>> + $ref: /schemas/types.yaml#/definitions/uint32
>> + enum: [2, 4, 6, 8, 10, 12, 14, 16]
>> + Description:
>> + Selects the drive strength for the specified pins, in mA.
>> +
>> + required:
>> + - pins
>> + - function
>> +
>> +required:
>> + - compatible
>> + - reg
>> + - interrupts
>> + - interrupt-controller
>> + - '#interrupt-cells'
>> + - gpio-controller
>> + - '#gpio-cells'
>> + - gpio-ranges
>> +
>> +example:
>> + tlmm: pinctrl@1000000 {
>> + compatible = "qcom,ipq6018-pinctrl";
>> + reg = <0x01000000 0x300000>;
>> + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
>> + gpio-controller;
>> + #gpio-cells = <2>;
>> + gpio-ranges = <&tlmm 0 80>;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> +
>> + serial_3_pins: serial3-pinmux {
>> + pins = "gpio44", "gpio45";
>> + function = "blsp2_uart";
>> + drive-strength = <8>;
>> + bias-pull-down;
>> + };
>> + };
>> --
>> 1.9.1
>>
--
"QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH V3 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings
2020-01-03 11:49 ` [PATCH V3 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings Sricharan R
2020-01-04 0:58 ` Rob Herring
@ 2020-01-07 11:55 ` Linus Walleij
2020-01-09 9:21 ` Sricharan R
1 sibling, 1 reply; 12+ messages in thread
From: Linus Walleij @ 2020-01-07 11:55 UTC (permalink / raw)
To: Sricharan R
Cc: Andy Gross,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Linux ARM, MSM, linux-clk, open list:GPIO SUBSYSTEM,
linux-kernel, open list:ARM/QUALCOMM SUPPORT, Rob Herring,
Stephen Boyd, sivaprak
On Fri, Jan 3, 2020 at 12:49 PM Sricharan R <sricharan@codeaurora.org> wrote:
> Add device tree binding Documentation details for ipq6018
> pinctrl driver.
>
> Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
> Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
> Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
> Signed-off-by: Sricharan R <sricharan@codeaurora.org>
> ---
> [v3] Fixed the example dt node, inherited properties
Once you are done with patches 1 & 2, can I merge these
separately to the pinctrl tree?
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH V3 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings
2020-01-07 11:55 ` Linus Walleij
@ 2020-01-09 9:21 ` Sricharan R
0 siblings, 0 replies; 12+ messages in thread
From: Sricharan R @ 2020-01-09 9:21 UTC (permalink / raw)
To: Linus Walleij
Cc: Andy Gross,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Linux ARM, MSM, linux-clk, open list:GPIO SUBSYSTEM,
linux-kernel, open list:ARM/QUALCOMM SUPPORT, Rob Herring,
Stephen Boyd, sivaprak
Hi Linus,
On 1/7/2020 5:25 PM, Linus Walleij wrote:
> On Fri, Jan 3, 2020 at 12:49 PM Sricharan R <sricharan@codeaurora.org> wrote:
>
>> Add device tree binding Documentation details for ipq6018
>> pinctrl driver.
>>
>> Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
>> Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
>> Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
>> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
>> Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
>> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
>> Signed-off-by: Sricharan R <sricharan@codeaurora.org>
>> ---
>> [v3] Fixed the example dt node, inherited properties
>
> Once you are done with patches 1 & 2, can I merge these
> separately to the pinctrl tree?
Yeah, that should be fine. Posted a V4 and waiting for approval
from Rob on the pinctrl bindings for Patch 1.
Regards,
Sricharan
--
"QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2020-01-09 9:21 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-01-03 11:49 [PATCH V3 0/5] Add minimal boot support for IPQ6018 Sricharan R
2020-01-03 11:49 ` [PATCH V3 1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings Sricharan R
2020-01-04 0:58 ` Rob Herring
2020-01-06 5:25 ` Sricharan R
2020-01-07 11:55 ` Linus Walleij
2020-01-09 9:21 ` Sricharan R
2020-01-03 11:49 ` [PATCH V3 2/5] pinctrl: qcom: Add ipq6018 pinctrl driver Sricharan R
2020-01-04 1:33 ` Bjorn Andersson
2020-01-03 11:49 ` [PATCH V3 3/5] dt-bindings: qcom: Add ipq6018 bindings Sricharan R
2020-01-04 0:59 ` Rob Herring
2020-01-03 11:49 ` [PATCH V3 4/5] arm64: dts: Add ipq6018 SoC and CP01 board support Sricharan R
2020-01-03 11:49 ` [PATCH V3 5/5] arm64: defconfig: Enable qcom ipq6018 clock and pinctrl Sricharan R
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).