linux-clk.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH v4 00/16] Support ROHM BD71828 PMIC
@ 2019-11-16 18:55 Matti Vaittinen
  2019-11-16 18:55 ` [PATCH v4 01/16] dt-bindings: regulator: Document ROHM BD71282 regulator bindings Matti Vaittinen
                   ` (15 more replies)
  0 siblings, 16 replies; 19+ messages in thread
From: Matti Vaittinen @ 2019-11-16 18:55 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Lee Jones, Jacek Anaszewski, Pavel Machek, Dan Murphy,
	Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Mauro Carvalho Chehab, Jeff Kirsher, Wolfram Sang,
	Marek Szyprowski, Heiner Kallweit, Nicholas Mc Guire,
	Phil Edworthy, linux-leds, devicetree, linux-kernel, linux-doc,
	linux-clk, linux-gpio, linux-rtc

Patch series introducing support for ROHM BD71828 PMIC

ROHM BD71828 is a power management IC containing 7 bucks and 7 LDOs. All
regulators can either be controlled individually via I2C. Bucks 1,2,6 and
7 can also be assigned to a "regulator group" controlled by run-levels.
Eg. Run level specific voltages and enable/disable statuses for each of
these bucks can be set via register interface. The buck run-level group
assignment (selection if buck is to be controlled individually or via
run-levels) can be changed at run-time via I2C.

Run level changes can then be initiated wither via I2C writes or GPIO.
and when run-level is changed, state of all bucks which are set to be
controlled via run-levels are changed accrdingly.

This control mechanism selection (I2C or GPIO) is selected by data in
one time programmable PMIC memory area (during production) and can't be
changed later.

In addition to the bucks and LDOs there are:

- The usual clk gate
- 4 IO pins (mostly usable as GPO or tied to specific purpose)
- power button support
- RTC
- two LEDs
- battery charger
- HALL sensor input

This patch series adds support to regulators, clk, RTC, GPIOs and LEDs.

Power-supply driver for charger is "under construction" and not included
in this series.

The series also adds LED DT-node lookup based on node name or given
property name/value pair in LED core. It also adds generic default-state
and default-trigger property handling to LED core. Follow-up patches
simplifying few other LED drivers should follow.

In GPIO framework this series adds devm-support for gpio_array getting
for MFD sub-devices whose GPIO consumer information may be in parent
device's DT node. And while I was at it I also added few missing GPIO devm
functions to the documentaton listing.

Changelog v4 (first non RFC):
  General:
    - Changed subdevice loading and chip version identification to use
      platform ID.
    - License identifiers changed to GPL-2.0-only
  MFD:
    - Styling fixes mostly
  DT-Bindings:
    - a few more checks as suggested by Rob Herring.
    - Order of DT patches changed.
    - me as maintainer
    - standard units to new properties (microvolts, ohms)
    - runlevel values in an array
  LED:
    - BD71828 driver added (back)
      - Added DT support
    - Added LED DT node lookup in led framework when init_data is given
      with DT node match information.
    - Added common property parsing for default-state and
      default-trigger.
  Regulators:
    - dropped sysfs interfaces
    - fixed module unload/reload by binding gpio consumer information to
      regulator device not to MFD.
  GPIO:
    - Added devm_gpiod_get_parent_array
    - added few missing devm functions to documentation

Changelog v3:
  DT-Bindings:
    - yamlify
    - add LED binding doc
  CLK:
    - Move clk register definitions from MFD headers to clk driver
  GPIO:
    - Add generic direction define and use it.
  LED:
    - Drop LED driver from the series (for now).

Changelog v2: Mainly RTC and GPIO fixes suggested by Alexandre and Bartosz
  General:
    -Patch ordering changed to provide dt binding documents right after the
     MFD core.
  DT-Bindings for regulators (Patch 3)
    -Fix typo in PMIC model number
  RTC (patch 11)
    -Reverted renaming in order to reduce patch size.
    -Reworded commit message
  BD71828 regulator (patch 7)
    -Add MODULE_ALIAS
  GPIO (patch 12)
    -Remove file-name from comment
    -prefix IN and OUT defines with chip type
    -improved documentation for the INPUT only pin.
    -removed empty left-over function
    -removed unnecessary #ifdef CONFIG_OF_GPIO
    -removed unnecessary error print
    -Add MODULE_ALIAS

Patch 1:
        dt-bindings for regulators on BD71828 PMIC
Patch 2:
        dt-bindings for LEDs on BD71828 PMIC
Patch 3:
	dt-bindings for BD71828 PMIC
Patch 4:
	Convert rohm PMICs with common sub-devices to use platform_
	device_id to match MFD sub-devices
Patch 5:
        BD71828 MFD core.
Patch 6:
	Power button support using GPIO keys.
Patch 7:
        CLK gate support using existing clk-bd718x7
Patch 8:
        Split existing bd718x7 regulator driver to generic ROHM dt
        parsing portion (used by more than one ROHM drivers) and
        bd718x8 specific parts
Patch 9:
        Basic regulator support (individual control via I2C). This
        should be pretty standard stuff.
Patch 10:
	Add devm_gpiod_get_parent_array
Patch 11:
	Add missing managed GPIO array get functions to documentation
Patch 12:
        Add support for getting regulator voltages when run-levels are
	used. Allow specifying voltages for run-levels via DT and
	in-kernel API. Support changing run-levels via in-kernel API.
Patch 13:
        Support BD71828 RTC block using BD70528 RTC driver
Patch 14:
        Allow control of GP(I)O pins on BD71828 via GPIO subsystem
Patch 15:
	Add LED node lookup and common LED binding parsing support
	to LED class/core
Patch 16:
        Support toggling the LEDs on BD71828.

This patch series is based on v5.4-rc7

---

Matti Vaittinen (16):
  dt-bindings: regulator: Document ROHM BD71282 regulator bindings
  dt-bindings: leds: ROHM BD71282 PMIC LED driver
  dt-bindings: mfd: Document ROHM BD71828 bindings
  mfd: rohm PMICs - use platform_device_id to match MFD sub-devices
  mfd: bd71828: Support ROHM BD71828 PMIC - core
  mfd: input: bd71828: Add power-key support
  clk: bd718x7: Support ROHM BD71828 clk block
  regulator: bd718x7: Split driver to common and bd718x7 specific parts
  regulator: bd71828: Basic support for ROHM bd71828 PMIC regulators
  gpio: devres: Add devm_gpiod_get_parent_array
  docs: driver-model: Add missing managed GPIO array get functions
  regulator: bd71828: Add GPIO based run-level control for regulators
  rtc: bd70528 add BD71828 support
  gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs
  leds: Add common LED binding parsing support to LED class/core
  led: bd71828: Support LED outputs on ROHM BD71828 PMIC

 .../bindings/leds/rohm,bd71828-leds.yaml      |   49 +
 .../bindings/mfd/rohm,bd71828-pmic.yaml       |  249 +++
 .../regulator/rohm,bd71828-regulator.yaml     |  122 ++
 .../driver-api/driver-model/devres.rst        |    3 +
 drivers/clk/Kconfig                           |    6 +-
 drivers/clk/clk-bd718x7.c                     |   50 +-
 drivers/gpio/Kconfig                          |   12 +
 drivers/gpio/Makefile                         |    1 +
 drivers/gpio/gpio-bd71828.c                   |  159 ++
 drivers/gpio/gpiolib-devres.c                 |   65 +-
 drivers/leds/Kconfig                          |   10 +
 drivers/leds/Makefile                         |    1 +
 drivers/leds/led-class.c                      |   88 +-
 drivers/leds/led-core.c                       |  246 ++-
 drivers/leds/leds-bd71828.c                   |  104 ++
 drivers/mfd/Kconfig                           |   15 +
 drivers/mfd/Makefile                          |    2 +-
 drivers/mfd/rohm-bd70528.c                    |    3 +-
 drivers/mfd/rohm-bd71828.c                    |  345 +++++
 drivers/mfd/rohm-bd718x7.c                    |   39 +-
 drivers/regulator/Kconfig                     |   16 +
 drivers/regulator/Makefile                    |    2 +
 drivers/regulator/bd71828-regulator.c         | 1374 +++++++++++++++++
 drivers/regulator/bd718x7-regulator.c         |  200 +--
 drivers/regulator/rohm-regulator.c            |   95 ++
 drivers/rtc/Kconfig                           |    3 +-
 drivers/rtc/rtc-bd70528.c                     |  167 +-
 include/linux/gpio/consumer.h                 |    5 +
 include/linux/leds.h                          |   90 +-
 include/linux/mfd/rohm-bd70528.h              |   19 +-
 include/linux/mfd/rohm-bd71828.h              |  428 +++++
 include/linux/mfd/rohm-bd718x7.h              |    6 -
 include/linux/mfd/rohm-generic.h              |   48 +-
 include/linux/mfd/rohm-shared.h               |   27 +
 34 files changed, 3772 insertions(+), 277 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/leds/rohm,bd71828-leds.yaml
 create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml
 create mode 100644 Documentation/devicetree/bindings/regulator/rohm,bd71828-regulator.yaml
 create mode 100644 drivers/gpio/gpio-bd71828.c
 create mode 100644 drivers/leds/leds-bd71828.c
 create mode 100644 drivers/mfd/rohm-bd71828.c
 create mode 100644 drivers/regulator/bd71828-regulator.c
 create mode 100644 drivers/regulator/rohm-regulator.c
 create mode 100644 include/linux/mfd/rohm-bd71828.h
 create mode 100644 include/linux/mfd/rohm-shared.h


base-commit: 31f4f5b495a62c9a8b15b1c3581acd5efeb9af8c
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply	[flat|nested] 19+ messages in thread

* [PATCH v4 01/16] dt-bindings: regulator: Document ROHM BD71282 regulator bindings
  2019-11-16 18:55 [PATCH v4 00/16] Support ROHM BD71828 PMIC Matti Vaittinen
@ 2019-11-16 18:55 ` Matti Vaittinen
  2019-11-16 18:56 ` [PATCH v4 02/16] dt-bindings: leds: ROHM BD71282 PMIC LED driver Matti Vaittinen
                   ` (14 subsequent siblings)
  15 siblings, 0 replies; 19+ messages in thread
From: Matti Vaittinen @ 2019-11-16 18:55 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Lee Jones, Jacek Anaszewski, Pavel Machek, Dan Murphy,
	Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Mauro Carvalho Chehab, Jeff Kirsher, Wolfram Sang,
	Marek Szyprowski, Heiner Kallweit, Nicholas Mc Guire,
	Phil Edworthy, linux-leds, devicetree, linux-kernel, linux-doc,
	linux-clk, linux-gpio, linux-rtc

Document ROHM BD71828 PMIC regulator device tree bindings.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
 .../regulator/rohm,bd71828-regulator.yaml     | 122 ++++++++++++++++++
 1 file changed, 122 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/regulator/rohm,bd71828-regulator.yaml

diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd71828-regulator.yaml b/Documentation/devicetree/bindings/regulator/rohm,bd71828-regulator.yaml
new file mode 100644
index 000000000000..c23ec4d8584b
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/rohm,bd71828-regulator.yaml
@@ -0,0 +1,122 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/rohm,bd71828-regulator.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ROHM BD71828 Power Management Integrated Circuit regulators
+
+maintainers:
+  - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
+
+description: |
+  This module is part of the ROHM BD71828 MFD device. For more details
+  see Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml.
+
+  The regulator controller is represented as a sub-node of the PMIC node
+  on the device tree.
+
+  Regulator nodes should be named to BUCK_<number> and LDO_<number>.
+  The valid names for BD71828 regulator nodes are
+  BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6, BUCK7
+  LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7
+
+patternProperties:
+  "^LDO[1-7]$":
+    type: object
+    allOf:
+      - $ref: regulator.yaml#
+    description:
+      Properties for single LDO regulator.
+
+    properties:
+      #Is there a nice way to check the name is same as node name but lower case
+      regulator-name:
+        pattern: "^ldo[1-7]$"
+        description:
+          should be "ldo1", ..., "ldo7"
+
+  "^BUCK[1-7]$":
+    type: object
+    allOf:
+      - $ref: regulator.yaml#
+    description:
+      Properties for single BUCK regulator.
+
+    properties:
+      #Is there a nice way to check the name is same as node name but lower case
+      regulator-name:
+        pattern: "^buck[1-7]$"
+        description:
+          should be "buck1", ..., "buck7"
+
+      rohm,dvs-run-voltage:
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - minimum: 0
+            maximum: 3300000
+        description:
+          PMIC default "RUN" state voltage in uV. See below table for
+          bucks which support this. 0 means disabled.
+
+      rohm,dvs-idle-voltage:
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - minimum: 0
+            maximum: 3300000
+        description:
+          PMIC default "IDLE" state voltage in uV. See below table for
+          bucks which support this. 0 means disabled.
+
+      rohm,dvs-suspend-voltage:
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - minimum: 0
+            maximum: 3300000
+        description:
+          PMIC default "SUSPEND" state voltage in uV. See below table for
+          bucks which support this. 0 means disabled.
+
+      rohm,dvs-lpsr-voltage:
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - minimum: 0
+            maximum: 3300000
+        description:
+          PMIC default "LPSR" state voltage in uV. See below table for
+          bucks which support this. 0 means disabled.
+
+#Supported default DVS states:
+#buck		| run		| idle		| suspend	| lpsr
+#----------------------------------------------------------------------------
+#1, 2, 6, and 7	| supported	| supported	| 	supported (*)
+#----------------------------------------------------------------------------
+#3, 4, and 5	| 			supported (**)
+#----------------------------------------------------------------------------
+#(*)  LPSR and SUSPEND states use same voltage but both states have own enable /
+#     disable settings. Voltage 0 can be specified for a state to make regulator
+#     disabled on that state.
+#(**) All states use same voltage but have own enable / disable settings.
+#     Voltage 0 can be specified for a state to make regulator disabled on that
+#     state.
+
+      rohm,dvs-runlvl-ctrl:
+        description: |
+          buck control is done based on run-level. Regulator is not
+          individually controllable. See ../mfd/rohm,bd71828-pmic.yaml for
+          how to specify run-level control mechanism. Only bucks 1, 2, 6
+          and 7 support this.
+        type: boolean
+
+      rohm,dvs-runlevel-microvolts:
+        minimum: 0
+        maximum: 2000000
+        maxItems: 4
+        description:
+          Array of voltages for run-levels. First value is for run-level 0,
+          second for run-level 1 etc. Microvolts.
+
+    required:
+      - regulator-name
+  additionalProperties: false
+additionalProperties: false
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply related	[flat|nested] 19+ messages in thread

* [PATCH v4 02/16] dt-bindings: leds: ROHM BD71282 PMIC LED driver
  2019-11-16 18:55 [PATCH v4 00/16] Support ROHM BD71828 PMIC Matti Vaittinen
  2019-11-16 18:55 ` [PATCH v4 01/16] dt-bindings: regulator: Document ROHM BD71282 regulator bindings Matti Vaittinen
@ 2019-11-16 18:56 ` Matti Vaittinen
  2019-11-16 18:56 ` [PATCH v4 03/16] dt-bindings: mfd: Document ROHM BD71828 bindings Matti Vaittinen
                   ` (13 subsequent siblings)
  15 siblings, 0 replies; 19+ messages in thread
From: Matti Vaittinen @ 2019-11-16 18:56 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Lee Jones, Jacek Anaszewski, Pavel Machek, Dan Murphy,
	Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Mauro Carvalho Chehab, Jeff Kirsher, Wolfram Sang,
	Marek Szyprowski, Heiner Kallweit, Nicholas Mc Guire,
	Phil Edworthy, linux-leds, devicetree, linux-kernel, linux-doc,
	linux-clk, linux-gpio, linux-rtc

Document ROHM BD71828 PMIC LED driver device tree bindings.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
 .../bindings/leds/rohm,bd71828-leds.yaml      | 49 +++++++++++++++++++
 1 file changed, 49 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/leds/rohm,bd71828-leds.yaml

diff --git a/Documentation/devicetree/bindings/leds/rohm,bd71828-leds.yaml b/Documentation/devicetree/bindings/leds/rohm,bd71828-leds.yaml
new file mode 100644
index 000000000000..e72c9ae0fc2a
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/rohm,bd71828-leds.yaml
@@ -0,0 +1,49 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/leds/rohm,bd71828-leds.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ROHM BD71828 Power Management Integrated Circuit LED driver
+
+maintainers:
+  - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
+
+description: |
+  This module is part of the ROHM BD71828 MFD device. For more details
+  see Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml.
+
+  The LED controller is represented as a sub-node of the PMIC node on the device
+  tree.
+
+  The device has two LED outputs referred as GRNLED and AMBLED in data-sheet.
+
+properties:
+  compatible:
+    const: rohm,bd71828-leds
+
+patternProperties:
+  "^led-[1-2]$":
+    type: object
+    description:
+      Properties for a single LED.
+    properties:
+      #$ref: "common.yaml#"
+      rohm,led-compatible:
+        description: LED identification string
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/string"
+          - oneOf:
+            - const: bd71828-ambled
+            - const: bd71828-grnled
+      function:
+        description:
+          Purpose of LED as defined in dt-bindings/leds/common.h
+        $ref: "/schemas/types.yaml#/definitions/string"
+      color:
+        description:
+          LED colour as defined in dt-bindings/leds/common.h
+        $ref: "/schemas/types.yaml#/definitions/uint32"
+
+required:
+  - compatible
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply related	[flat|nested] 19+ messages in thread

* [PATCH v4 03/16] dt-bindings: mfd: Document ROHM BD71828 bindings
  2019-11-16 18:55 [PATCH v4 00/16] Support ROHM BD71828 PMIC Matti Vaittinen
  2019-11-16 18:55 ` [PATCH v4 01/16] dt-bindings: regulator: Document ROHM BD71282 regulator bindings Matti Vaittinen
  2019-11-16 18:56 ` [PATCH v4 02/16] dt-bindings: leds: ROHM BD71282 PMIC LED driver Matti Vaittinen
@ 2019-11-16 18:56 ` Matti Vaittinen
  2019-11-16 18:57 ` [PATCH v4 04/16] mfd: rohm PMICs - use platform_device_id to match MFD sub-devices Matti Vaittinen
                   ` (12 subsequent siblings)
  15 siblings, 0 replies; 19+ messages in thread
From: Matti Vaittinen @ 2019-11-16 18:56 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Lee Jones, Jacek Anaszewski, Pavel Machek, Dan Murphy,
	Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Mauro Carvalho Chehab, Jeff Kirsher, Wolfram Sang,
	Marek Szyprowski, Heiner Kallweit, Nicholas Mc Guire,
	Phil Edworthy, linux-leds, devicetree, linux-kernel, linux-doc,
	linux-clk, linux-gpio, linux-rtc

ROHM BD71828 Power management IC integrates 7 buck converters, 7 LDOs,
a real-time clock (RTC), 3 GPO/regulator control pins, HALL input
and a 32.768 kHz clock gate.

Document the dt bindings drivers are using.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
 .../bindings/mfd/rohm,bd71828-pmic.yaml       | 249 ++++++++++++++++++
 1 file changed, 249 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml

diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml
new file mode 100644
index 000000000000..17ea9fa463e8
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml
@@ -0,0 +1,249 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/rohm,bd71828-pmic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ROHM BD71828 Power Management Integrated Circuit bindings
+
+maintainers:
+  - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
+
+description: |
+  BD71828GW is a single-chip power management IC for battery-powered portable
+  devices. The IC integrates 7 buck converters, 7 LDOs, and a 1500 mA
+  single-cell linear charger. Also included is a Coulomb counter, a real-time
+  clock (RTC), and a 32.768 kHz clock gate.
+
+  The BD71828 RUN state is divided into 4 configurable run-levels named RUN0,
+  RUN1, RUN2 and RUN3. Bucks 1, 2, 6 and 7 can be either controlled individually
+  via I2C, or some/all of them can be bound to run-levels and controlled as a
+  group. If bucks are controlled individually these run-levels are ignored. See
+  ../regulator/rohm,bd71828-regulator.yaml for how to define regulator voltages
+  for run-levels. Run-levels can be changed by I2C or GPIO depending on PMIC's
+  OTP configuration.
+
+properties:
+  compatible:
+    const: rohm,bd71828
+
+  reg:
+    description:
+      I2C slave address.
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+    description:
+      The interrupt line the device is connected to.
+
+  gpio-controller: true
+      # Indicate BD71828 acts as a GPIO controller.
+
+  "#gpio-cells":
+    const: 2
+    description: |
+      The first cell is the pin number and the second cell is used to specify
+      flags. See ../gpio/gpio.txt for more information.
+
+  clocks:
+    maxItems: 1
+    description:
+      The parent clock connected to PMIC.
+
+  "#clock-cells":
+    const: 0
+
+  rohm,charger-sense-resistor-ohms:
+    minimum: 10000000
+    maximum: 50000000
+    description: |
+      BD71827 and BD71828 have SAR ADC for measuring charging currents.
+      External sense resistor (RSENSE in data sheet) should be used. If some
+      other but 30MOhm resistor is used the resistance value should be given
+      here in Ohms.
+
+  regulators:
+    $ref: ../regulator/rohm,bd71828-regulator.yaml
+    description:
+      List of child nodes that specify the regulators.
+
+  leds:
+    $ref: ../leds/rohm,bd71828-leds.yaml
+
+  rohm,dvs-vsel-gpios:
+    maxItems: 2
+    description: |
+      GPIOs used to control PMIC run-levels. Should describe two GPIOs.
+      (See run-level control in data-sheet). If this property is omitted but
+      some bucks are marked to be controlled by run-levels - then OTP option
+      allowing run-level control via I2C is assumed.
+
+  gpio-reserved-ranges:
+    description: |
+      Usage of BD71828 GPIO pins can be changed via OTP. This property can be
+      used to mark the pins which should not be configured for GPIO. Please see
+      the ../gpio/gpio.txt for more information.
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - "#clock-cells"
+  - regulators
+  - gpio-controller
+  - "#gpio-cells"
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/leds/common.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        pmic: pmic@4b {
+            compatible = "rohm,bd71828";
+            reg = <0x4b>;
+
+            interrupt-parent = <&gpio1>;
+            interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+
+            clocks = <&osc 0>;
+            #clock-cells = <0>;
+            clock-output-names = "bd71828-32k-out";
+
+            gpio-controller;
+            #gpio-cells = <2>;
+            gpio-reserved-ranges = <0 1>, <2 1>;
+
+            rohm,dvs-vsel-gpios = <&gpio1 12 0>, <&gpio1 13 0>;
+            rohm,charger-sense-resistor-ohms = <10000000>;
+
+            regulators {
+                buck1: BUCK1 {
+                    regulator-name = "buck1";
+                    regulator-min-microvolt = <500000>;
+                    regulator-max-microvolt = <2000000>;
+                    regulator-ramp-delay = <2500>;
+                    rohm,dvs-runlvl-ctrl;
+                    rohm,dvs-runlevel-microvolts  = <500000>,
+                                                    <506250>,
+                                                    <512500>,
+                                                    <518750>;
+                    regulator-boot-on;
+                };
+                buck2: BUCK2 {
+                    regulator-name = "buck2";
+                    regulator-min-microvolt = <500000>;
+                    regulator-max-microvolt = <2000000>;
+                    regulator-ramp-delay = <2500>;
+                    rohm,dvs-runlvl-ctrl;
+                    rohm,dvs-runlevel-microvolts  = <500000>,
+                                                    <506250>,
+                                                    <512500>,
+                                                    <518750>;
+                    regulator-boot-on;
+                };
+                buck3: BUCK3 {
+                    regulator-name = "buck3";
+                    regulator-min-microvolt = <1200000>;
+                    regulator-max-microvolt = <2000000>;
+                    regulator-boot-on;
+                };
+                buck4: BUCK4 {
+                    regulator-name = "buck4";
+                    regulator-min-microvolt = <1000000>;
+                    regulator-max-microvolt = <1800000>;
+                    regulator-boot-on;
+                };
+                buck5: BUCK5 {
+                    regulator-name = "buck5";
+                    regulator-min-microvolt = <2500000>;
+                    regulator-max-microvolt = <3300000>;
+                    regulator-boot-on;
+                };
+                buck6: BUCK6 {
+                    regulator-name = "buck6";
+                    regulator-min-microvolt = <500000>;
+                    regulator-max-microvolt = <2000000>;
+                    regulator-ramp-delay = <2500>;
+                    rohm,dvs-runlvl-ctrl;
+                    rohm,dvs-runlevel-microvolts  = <500000>,
+                                                    <506250>,
+                                                    <512500>,
+                                                    <518750>;
+                    regulator-boot-on;
+                };
+                buck7: BUCK7 {
+                    regulator-name = "buck7";
+                    regulator-min-microvolt = <500000>;
+                    regulator-max-microvolt = <2000000>;
+                    regulator-ramp-delay = <2500>;
+                    rohm,dvs-runlvl-ctrl;
+                    rohm,dvs-runlevel-microvolts  = <500000>,
+                                                    <506250>,
+                                                    <512500>,
+                                                    <518750>;
+                    regulator-boot-on;
+                };
+                ldo1: LDO1 {
+                    regulator-name = "ldo1";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <3300000>;
+                    regulator-boot-on;
+                };
+                ldo2: LDO2 {
+                    regulator-name = "ldo2";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <3300000>;
+                    regulator-boot-on;
+                };
+                ldo3: LDO3 {
+                    regulator-name = "ldo3";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <3300000>;
+                    regulator-boot-on;
+                };
+                ldo4: LDO4 {
+                    regulator-name = "ldo4";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <3300000>;
+                    regulator-boot-on;
+                };
+                ldo5: LDO5 {
+                    regulator-name = "ldo5";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <3300000>;
+                    regulator-boot-on;
+                };
+                ldo6: LDO6 {
+                    regulator-name = "ldo6";
+                    regulator-min-microvolt = <1800000>;
+                    regulator-max-microvolt = <1800000>;
+                    regulator-boot-on;
+                };
+                ldo7_reg: LDO7 {
+                    regulator-name = "ldo7";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <3300000>;
+                    regulator-boot-on;
+                };
+            };
+
+            leds {
+                compatible = "rohm,bd71828-leds";
+
+                led-1 {
+                    rohm,led-compatible = "bd71828-grnled";
+                    function = LED_FUNCTION_INDICATOR;
+                    color = <LED_COLOR_ID_GREEN>;
+                };
+                led-2 {
+                    rohm,led-compatible = "bd71828-ambled";
+                    function = LED_FUNCTION_CHARGING;
+                    color = <LED_COLOR_ID_AMBER>;
+                };
+            };
+        };
+    };
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply related	[flat|nested] 19+ messages in thread

* [PATCH v4 04/16] mfd: rohm PMICs - use platform_device_id to match MFD sub-devices
  2019-11-16 18:55 [PATCH v4 00/16] Support ROHM BD71828 PMIC Matti Vaittinen
                   ` (2 preceding siblings ...)
  2019-11-16 18:56 ` [PATCH v4 03/16] dt-bindings: mfd: Document ROHM BD71828 bindings Matti Vaittinen
@ 2019-11-16 18:57 ` Matti Vaittinen
  2019-11-16 18:57 ` [PATCH v4 05/16] mfd: bd71828: Support ROHM BD71828 PMIC - core Matti Vaittinen
                   ` (11 subsequent siblings)
  15 siblings, 0 replies; 19+ messages in thread
From: Matti Vaittinen @ 2019-11-16 18:57 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Lee Jones, Jacek Anaszewski, Pavel Machek, Dan Murphy,
	Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Mauro Carvalho Chehab, Jeff Kirsher, Wolfram Sang,
	Marek Szyprowski, Heiner Kallweit, Nicholas Mc Guire,
	Phil Edworthy, linux-leds, devicetree, linux-kernel, linux-doc,
	linux-clk, linux-gpio, linux-rtc

Thanks to Stephen Boyd I today learned we can use platform_device_id
to do device and module matching for MFD sub-devices!

Do device matching using the platform_device_id instead of using
explicit module_aliases to load modules and custom parent-data field
to do module loading and sub-device matching.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
 drivers/clk/clk-bd718x7.c             | 12 ++++++++-
 drivers/mfd/rohm-bd70528.c            |  3 +--
 drivers/mfd/rohm-bd718x7.c            | 39 ++++++++++++++++++++++-----
 drivers/regulator/bd718x7-regulator.c | 17 +++++++++---
 include/linux/mfd/rohm-generic.h      |  3 +--
 5 files changed, 58 insertions(+), 16 deletions(-)

diff --git a/drivers/clk/clk-bd718x7.c b/drivers/clk/clk-bd718x7.c
index ae6e5baee330..1c1764f74d0a 100644
--- a/drivers/clk/clk-bd718x7.c
+++ b/drivers/clk/clk-bd718x7.c
@@ -74,6 +74,7 @@ static int bd71837_clk_probe(struct platform_device *pdev)
 		.name = "bd718xx-32k-out",
 		.ops = &bd71837_clk_ops,
 	};
+	enum rohm_chip_type chip = platform_get_device_id(pdev)->driver_data;
 
 	c = devm_kzalloc(&pdev->dev, sizeof(*c), GFP_KERNEL);
 	if (!c)
@@ -87,7 +88,7 @@ static int bd71837_clk_probe(struct platform_device *pdev)
 		dev_err(&pdev->dev, "No parent clk found\n");
 		return -EINVAL;
 	}
-	switch (mfd->chip_type) {
+	switch (chip) {
 	case ROHM_CHIP_TYPE_BD71837:
 	case ROHM_CHIP_TYPE_BD71847:
 		c->reg = BD718XX_REG_OUT32K;
@@ -121,11 +122,20 @@ static int bd71837_clk_probe(struct platform_device *pdev)
 	return rval;
 }
 
+static const struct platform_device_id bd718x7_clk_id[] = {
+	{ "bd71837-clk", ROHM_CHIP_TYPE_BD71837 },
+	{ "bd71847-clk", ROHM_CHIP_TYPE_BD71847 },
+	{ "bd70528-clk", ROHM_CHIP_TYPE_BD70528 },
+	{ },
+};
+MODULE_DEVICE_TABLE(platform, bd718x7_clk_id);
+
 static struct platform_driver bd71837_clk = {
 	.driver = {
 		.name = "bd718xx-clk",
 	},
 	.probe = bd71837_clk_probe,
+	.id_table = bd718x7_clk_id,
 };
 
 module_platform_driver(bd71837_clk);
diff --git a/drivers/mfd/rohm-bd70528.c b/drivers/mfd/rohm-bd70528.c
index 55599d5c5c86..e66a4a1c3731 100644
--- a/drivers/mfd/rohm-bd70528.c
+++ b/drivers/mfd/rohm-bd70528.c
@@ -48,7 +48,7 @@ static struct mfd_cell bd70528_mfd_cells[] = {
 	 * We use BD71837 driver to drive the clock block. Only differences to
 	 * BD70528 clock gate are the register address and mask.
 	 */
-	{ .name = "bd718xx-clk", },
+	{ .name = "bd70528-clk", },
 	{ .name = "bd70528-wdt", },
 	{
 		.name = "bd70528-power",
@@ -237,7 +237,6 @@ static int bd70528_i2c_probe(struct i2c_client *i2c,
 
 	dev_set_drvdata(&i2c->dev, &bd70528->chip);
 
-	bd70528->chip.chip_type = ROHM_CHIP_TYPE_BD70528;
 	bd70528->chip.regmap = devm_regmap_init_i2c(i2c, &bd70528_regmap);
 	if (IS_ERR(bd70528->chip.regmap)) {
 		dev_err(&i2c->dev, "Failed to initialize Regmap\n");
diff --git a/drivers/mfd/rohm-bd718x7.c b/drivers/mfd/rohm-bd718x7.c
index 85e7f5133365..bb86ec829079 100644
--- a/drivers/mfd/rohm-bd718x7.c
+++ b/drivers/mfd/rohm-bd718x7.c
@@ -30,14 +30,24 @@ static struct gpio_keys_platform_data bd718xx_powerkey_data = {
 	.name = "bd718xx-pwrkey",
 };
 
-static struct mfd_cell bd718xx_mfd_cells[] = {
+static struct mfd_cell bd71837_mfd_cells[] = {
 	{
 		.name = "gpio-keys",
 		.platform_data = &bd718xx_powerkey_data,
 		.pdata_size = sizeof(bd718xx_powerkey_data),
 	},
-	{ .name = "bd718xx-clk", },
-	{ .name = "bd718xx-pmic", },
+	{ .name = "bd71837-clk", },
+	{ .name = "bd71837-pmic", },
+};
+
+static struct mfd_cell bd71847_mfd_cells[] = {
+	{
+		.name = "gpio-keys",
+		.platform_data = &bd718xx_powerkey_data,
+		.pdata_size = sizeof(bd718xx_powerkey_data),
+	},
+	{ .name = "bd71847-clk", },
+	{ .name = "bd71847-pmic", },
 };
 
 static const struct regmap_irq bd718xx_irqs[] = {
@@ -124,6 +134,9 @@ static int bd718xx_i2c_probe(struct i2c_client *i2c,
 {
 	struct bd718xx *bd718xx;
 	int ret;
+	unsigned int chip_type;
+	struct mfd_cell *mfd;
+	int cells;
 
 	if (!i2c->irq) {
 		dev_err(&i2c->dev, "No IRQ configured\n");
@@ -136,8 +149,21 @@ static int bd718xx_i2c_probe(struct i2c_client *i2c,
 		return -ENOMEM;
 
 	bd718xx->chip_irq = i2c->irq;
-	bd718xx->chip.chip_type = (unsigned int)(uintptr_t)
-				of_device_get_match_data(&i2c->dev);
+	chip_type = (unsigned int)(uintptr_t)
+		    of_device_get_match_data(&i2c->dev);
+	switch (chip_type) {
+	case ROHM_CHIP_TYPE_BD71837:
+		mfd = bd71837_mfd_cells;
+		cells = ARRAY_SIZE(bd71837_mfd_cells);
+		break;
+	case ROHM_CHIP_TYPE_BD71847:
+		mfd = bd71847_mfd_cells;
+		cells = ARRAY_SIZE(bd71847_mfd_cells);
+		break;
+	default:
+		dev_err(&i2c->dev, "Unknown device type");
+		return -EINVAL;
+	}
 	bd718xx->chip.dev = &i2c->dev;
 	dev_set_drvdata(&i2c->dev, bd718xx);
 
@@ -170,8 +196,7 @@ static int bd718xx_i2c_probe(struct i2c_client *i2c,
 	button.irq = ret;
 
 	ret = devm_mfd_add_devices(bd718xx->chip.dev, PLATFORM_DEVID_AUTO,
-				   bd718xx_mfd_cells,
-				   ARRAY_SIZE(bd718xx_mfd_cells), NULL, 0,
+				   mfd, cells, NULL, 0,
 				   regmap_irq_get_domain(bd718xx->irq_data));
 	if (ret)
 		dev_err(&i2c->dev, "Failed to create subdevices\n");
diff --git a/drivers/regulator/bd718x7-regulator.c b/drivers/regulator/bd718x7-regulator.c
index bdab46a5c461..2058d972c7b7 100644
--- a/drivers/regulator/bd718x7-regulator.c
+++ b/drivers/regulator/bd718x7-regulator.c
@@ -1164,6 +1164,7 @@ static int bd718xx_probe(struct platform_device *pdev)
 
 	int i, j, err;
 	bool use_snvs;
+	enum rohm_chip_type chip = platform_get_device_id(pdev)->driver_data;
 
 	mfd = dev_get_drvdata(pdev->dev.parent);
 	if (!mfd) {
@@ -1172,8 +1173,8 @@ static int bd718xx_probe(struct platform_device *pdev)
 		goto err;
 	}
 
-	if (mfd->chip.chip_type >= ROHM_CHIP_TYPE_AMOUNT ||
-	    !pmic_regulators[mfd->chip.chip_type].r_datas) {
+	if (chip >= ROHM_CHIP_TYPE_AMOUNT || chip < 0 ||
+	    !pmic_regulators[chip].r_datas) {
 		dev_err(&pdev->dev, "Unsupported chip type\n");
 		err = -EINVAL;
 		goto err;
@@ -1215,13 +1216,13 @@ static int bd718xx_probe(struct platform_device *pdev)
 		}
 	}
 
-	for (i = 0; i < pmic_regulators[mfd->chip.chip_type].r_amount; i++) {
+	for (i = 0; i < pmic_regulators[chip].r_amount; i++) {
 
 		const struct regulator_desc *desc;
 		struct regulator_dev *rdev;
 		const struct bd718xx_regulator_data *r;
 
-		r = &pmic_regulators[mfd->chip.chip_type].r_datas[i];
+		r = &pmic_regulators[chip].r_datas[i];
 		desc = &r->desc;
 
 		config.dev = pdev->dev.parent;
@@ -1281,11 +1282,19 @@ static int bd718xx_probe(struct platform_device *pdev)
 	return err;
 }
 
+static const struct platform_device_id bd718x7_pmic_id[] = {
+	{ "bd71837-pmic", ROHM_CHIP_TYPE_BD71837 },
+	{ "bd71847-pmic", ROHM_CHIP_TYPE_BD71847 },
+	{ },
+};
+MODULE_DEVICE_TABLE(platform, bd718x7_pmic_id);
+
 static struct platform_driver bd718xx_regulator = {
 	.driver = {
 		.name = "bd718xx-pmic",
 	},
 	.probe = bd718xx_probe,
+	.id_table = bd718x7_pmic_id,
 };
 
 module_platform_driver(bd718xx_regulator);
diff --git a/include/linux/mfd/rohm-generic.h b/include/linux/mfd/rohm-generic.h
index bff15ac26f2c..922f88008232 100644
--- a/include/linux/mfd/rohm-generic.h
+++ b/include/linux/mfd/rohm-generic.h
@@ -4,7 +4,7 @@
 #ifndef __LINUX_MFD_ROHM_H__
 #define __LINUX_MFD_ROHM_H__
 
-enum {
+enum rohm_chip_type {
 	ROHM_CHIP_TYPE_BD71837 = 0,
 	ROHM_CHIP_TYPE_BD71847,
 	ROHM_CHIP_TYPE_BD70528,
@@ -12,7 +12,6 @@ enum {
 };
 
 struct rohm_regmap_dev {
-	unsigned int chip_type;
 	struct device *dev;
 	struct regmap *regmap;
 };
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply related	[flat|nested] 19+ messages in thread

* [PATCH v4 05/16] mfd: bd71828: Support ROHM BD71828 PMIC - core
  2019-11-16 18:55 [PATCH v4 00/16] Support ROHM BD71828 PMIC Matti Vaittinen
                   ` (3 preceding siblings ...)
  2019-11-16 18:57 ` [PATCH v4 04/16] mfd: rohm PMICs - use platform_device_id to match MFD sub-devices Matti Vaittinen
@ 2019-11-16 18:57 ` Matti Vaittinen
  2019-11-16 18:58 ` [PATCH v4 06/16] mfd: input: bd71828: Add power-key support Matti Vaittinen
                   ` (10 subsequent siblings)
  15 siblings, 0 replies; 19+ messages in thread
From: Matti Vaittinen @ 2019-11-16 18:57 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Lee Jones, Jacek Anaszewski, Pavel Machek, Dan Murphy,
	Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Mauro Carvalho Chehab, Jeff Kirsher, Wolfram Sang,
	Marek Szyprowski, Heiner Kallweit, Nicholas Mc Guire,
	Phil Edworthy, linux-leds, devicetree, linux-kernel, linux-doc,
	linux-clk, linux-gpio, linux-rtc

BD71828GW is a single-chip power management IC for battery-powered portable
devices. The IC integrates 7 buck converters, 7 LDOs, and a 1500 mA
single-cell linear charger. Also included is a Coulomb counter, a real-time
clock (RTC), 3 GPO/regulator control pins, HALL input and a 32.768 kHz
clock gate.

Add MFD core driver providing interrupt controller facilities and i2c
access to sub device drivers.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
 drivers/mfd/Kconfig              |  15 ++
 drivers/mfd/Makefile             |   2 +-
 drivers/mfd/rohm-bd71828.c       | 319 +++++++++++++++++++++++
 include/linux/mfd/rohm-bd71828.h | 425 +++++++++++++++++++++++++++++++
 include/linux/mfd/rohm-generic.h |   1 +
 5 files changed, 761 insertions(+), 1 deletion(-)
 create mode 100644 drivers/mfd/rohm-bd71828.c
 create mode 100644 include/linux/mfd/rohm-bd71828.h

diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index ae24d3ea68ea..ff06e853f799 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1913,6 +1913,21 @@ config MFD_ROHM_BD70528
 	  10 bits SAR ADC for battery temperature monitor and 1S battery
 	  charger.
 
+config MFD_ROHM_BD71828
+	tristate "ROHM BD71828 Power Management IC"
+	depends on I2C=y
+	depends on OF
+	select REGMAP_I2C
+	select REGMAP_IRQ
+	select MFD_CORE
+	help
+	  Select this option to get support for the ROHM BD71828 Power
+	  Management IC. BD71828GW is a single-chip power management IC for
+	  battery-powered portable devices. The IC integrates 7 buck
+	  converters, 7 LDOs, and a 1500 mA single-cell linear charger.
+	  Also included is a Coulomb counter, a real-time clock (RTC), and
+	  a 32.768 kHz clock gate.
+
 config MFD_STM32_LPTIMER
 	tristate "Support for STM32 Low-Power Timer"
 	depends on (ARCH_STM32 && OF) || COMPILE_TEST
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index c1067ea46204..437c47ffd315 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -253,6 +253,6 @@ obj-$(CONFIG_MFD_MXS_LRADC)     += mxs-lradc.o
 obj-$(CONFIG_MFD_SC27XX_PMIC)	+= sprd-sc27xx-spi.o
 obj-$(CONFIG_RAVE_SP_CORE)	+= rave-sp.o
 obj-$(CONFIG_MFD_ROHM_BD70528)	+= rohm-bd70528.o
+obj-$(CONFIG_MFD_ROHM_BD71828)	+= rohm-bd71828.o
 obj-$(CONFIG_MFD_ROHM_BD718XX)	+= rohm-bd718x7.o
 obj-$(CONFIG_MFD_STMFX) 	+= stmfx.o
-
diff --git a/drivers/mfd/rohm-bd71828.c b/drivers/mfd/rohm-bd71828.c
new file mode 100644
index 000000000000..7f445d699fd9
--- /dev/null
+++ b/drivers/mfd/rohm-bd71828.c
@@ -0,0 +1,319 @@
+// SPDX-License-Identifier: GPL-2.0-only
+//
+// Copyright (C) 2019 ROHM Semiconductors
+//
+// ROHM BD71828 PMIC driver
+
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/irq.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/rohm-bd71828.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/types.h>
+
+static const struct resource rtc_irqs[] = {
+	DEFINE_RES_IRQ_NAMED(BD71828_INT_RTC0, "bd71828-rtc-alm-0"),
+	DEFINE_RES_IRQ_NAMED(BD71828_INT_RTC1, "bd71828-rtc-alm-1"),
+	DEFINE_RES_IRQ_NAMED(BD71828_INT_RTC2, "bd71828-rtc-alm-2"),
+};
+
+static struct mfd_cell bd71828_mfd_cells[] = {
+	{ .name = "bd71828-pmic", },
+	{ .name = "bd71828-gpio", },
+	{ .name = "bd71828-led", .of_compatible = "rohm,bd71828-leds" },
+	/*
+	 * We use BD71837 driver to drive the clock block. Only differences to
+	 * BD70528 clock gate are the register address and mask.
+	 */
+	{ .name = "bd71828-clk", },
+	{ .name = "bd71827-power", },
+	{
+		.name = "bd71828-rtc",
+		.resources = rtc_irqs,
+		.num_resources = ARRAY_SIZE(rtc_irqs),
+	},
+};
+
+static const struct regmap_range volatile_ranges[] = {
+	{
+		.range_min = BD71828_REG_PS_CTRL_1,
+		.range_max = BD71828_REG_PS_CTRL_1,
+	}, {
+		.range_min = BD71828_REG_PS_CTRL_3,
+		.range_max = BD71828_REG_PS_CTRL_3,
+	}, {
+		.range_min = BD71828_REG_RTC_SEC,
+		.range_max = BD71828_REG_RTC_YEAR,
+	}, {
+		/*
+		 * For now make all charger registers volatile because many
+		 * needs to be and because the charger block is not that
+		 * performance critical.
+		 */
+		.range_min = BD71828_REG_CHG_STATE,
+		.range_max = BD71828_REG_CHG_FULL,
+	}, {
+		.range_min = BD71828_REG_INT_MAIN,
+		.range_max = BD71828_REG_IO_STAT,
+	},
+};
+
+static const struct regmap_access_table volatile_regs = {
+	.yes_ranges = &volatile_ranges[0],
+	.n_yes_ranges = ARRAY_SIZE(volatile_ranges),
+};
+
+static struct regmap_config bd71828_regmap = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.volatile_table = &volatile_regs,
+	.max_register = BD71828_MAX_REGISTER,
+	.cache_type = REGCACHE_RBTREE,
+};
+
+/*
+ * Mapping of main IRQ register bits to sub-IRQ register offsets so that we can
+ * access corect sub-IRQ registers based on bits that are set in main IRQ
+ * register.
+ */
+
+static unsigned int bit0_offsets[] = {11};		/* RTC IRQ */
+static unsigned int bit1_offsets[] = {10};		/* TEMP IRQ */
+static unsigned int bit2_offsets[] = {6, 7, 8, 9};	/* BAT MON IRQ */
+static unsigned int bit3_offsets[] = {5};		/* BAT IRQ */
+static unsigned int bit4_offsets[] = {4};		/* CHG IRQ */
+static unsigned int bit5_offsets[] = {3};		/* VSYS IRQ */
+static unsigned int bit6_offsets[] = {1, 2};		/* DCIN IRQ */
+static unsigned int bit7_offsets[] = {0};		/* BUCK IRQ */
+
+static struct regmap_irq_sub_irq_map bd71828_sub_irq_offsets[] = {
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit0_offsets),
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit1_offsets),
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit2_offsets),
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit3_offsets),
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit4_offsets),
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit5_offsets),
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit6_offsets),
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit7_offsets),
+};
+
+static struct regmap_irq bd71828_irqs[] = {
+	REGMAP_IRQ_REG(BD71828_INT_BUCK1_OCP, 0, BD71828_INT_BUCK1_OCP_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BUCK2_OCP, 0, BD71828_INT_BUCK2_OCP_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BUCK3_OCP, 0, BD71828_INT_BUCK3_OCP_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BUCK4_OCP, 0, BD71828_INT_BUCK4_OCP_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BUCK5_OCP, 0, BD71828_INT_BUCK5_OCP_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BUCK6_OCP, 0, BD71828_INT_BUCK6_OCP_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BUCK7_OCP, 0, BD71828_INT_BUCK7_OCP_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_PGFAULT, 0, BD71828_INT_PGFAULT_MASK),
+	/* DCIN1 interrupts */
+	REGMAP_IRQ_REG(BD71828_INT_DCIN_DET, 1, BD71828_INT_DCIN_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_DCIN_RMV, 1, BD71828_INT_DCIN_RMV_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_CLPS_OUT, 1, BD71828_INT_CLPS_OUT_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_CLPS_IN, 1, BD71828_INT_CLPS_IN_MASK),
+	/* DCIN2 interrupts */
+	REGMAP_IRQ_REG(BD71828_INT_DCIN_MON_RES, 2,
+		       BD71828_INT_DCIN_MON_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_DCIN_MON_DET, 2,
+		       BD71828_INT_DCIN_MON_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_LONGPUSH, 2, BD71828_INT_LONGPUSH_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_MIDPUSH, 2, BD71828_INT_MIDPUSH_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_SHORTPUSH, 2, BD71828_INT_SHORTPUSH_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_PUSH, 2, BD71828_INT_PUSH_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_WDOG, 2, BD71828_INT_WDOG_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_SWRESET, 2, BD71828_INT_SWRESET_MASK),
+	/* Vsys */
+	REGMAP_IRQ_REG(BD71828_INT_VSYS_UV_RES, 3,
+		       BD71828_INT_VSYS_UV_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_VSYS_UV_DET, 3,
+		       BD71828_INT_VSYS_UV_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_VSYS_LOW_RES, 3,
+		       BD71828_INT_VSYS_LOW_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_VSYS_LOW_DET, 3,
+		       BD71828_INT_VSYS_LOW_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_VSYS_HALL_IN, 3,
+		       BD71828_INT_VSYS_HALL_IN_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_VSYS_HALL_TOGGLE, 3,
+		       BD71828_INT_VSYS_HALL_TOGGLE_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_VSYS_MON_RES, 3,
+		       BD71828_INT_VSYS_MON_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_VSYS_MON_DET, 3,
+		       BD71828_INT_VSYS_MON_DET_MASK),
+	/* Charger */
+	REGMAP_IRQ_REG(BD71828_INT_CHG_DCIN_ILIM, 4,
+		       BD71828_INT_CHG_DCIN_ILIM_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_CHG_TOPOFF_TO_DONE, 4,
+		       BD71828_INT_CHG_TOPOFF_TO_DONE_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_CHG_WDG_TEMP, 4,
+		       BD71828_INT_CHG_WDG_TEMP_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_CHG_WDG_TIME, 4,
+		       BD71828_INT_CHG_WDG_TIME_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_CHG_RECHARGE_RES, 4,
+		       BD71828_INT_CHG_RECHARGE_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_CHG_RECHARGE_DET, 4,
+		       BD71828_INT_CHG_RECHARGE_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_CHG_RANGED_TEMP_TRANSITION, 4,
+		       BD71828_INT_CHG_RANGED_TEMP_TRANSITION_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_CHG_STATE_TRANSITION, 4,
+		       BD71828_INT_CHG_STATE_TRANSITION_MASK),
+	/* Battery */
+	REGMAP_IRQ_REG(BD71828_INT_BAT_TEMP_NORMAL, 5,
+		       BD71828_INT_BAT_TEMP_NORMAL_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_TEMP_ERANGE, 5,
+		       BD71828_INT_BAT_TEMP_ERANGE_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_TEMP_WARN, 5,
+		       BD71828_INT_BAT_TEMP_WARN_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_REMOVED, 5,
+		       BD71828_INT_BAT_REMOVED_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_DETECTED, 5,
+		       BD71828_INT_BAT_DETECTED_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_THERM_REMOVED, 5,
+		       BD71828_INT_THERM_REMOVED_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_THERM_DETECTED, 5,
+		       BD71828_INT_THERM_DETECTED_MASK),
+	/* Battery Mon 1 */
+	REGMAP_IRQ_REG(BD71828_INT_BAT_DEAD, 6, BD71828_INT_BAT_DEAD_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_SHORTC_RES, 6,
+		       BD71828_INT_BAT_SHORTC_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_SHORTC_DET, 6,
+		       BD71828_INT_BAT_SHORTC_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_LOW_VOLT_RES, 6,
+		       BD71828_INT_BAT_LOW_VOLT_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_LOW_VOLT_DET, 6,
+		       BD71828_INT_BAT_LOW_VOLT_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_VOLT_RES, 6,
+		       BD71828_INT_BAT_OVER_VOLT_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_VOLT_DET, 6,
+		       BD71828_INT_BAT_OVER_VOLT_DET_MASK),
+	/* Battery Mon 2 */
+	REGMAP_IRQ_REG(BD71828_INT_BAT_MON_RES, 7,
+		       BD71828_INT_BAT_MON_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_MON_DET, 7,
+		       BD71828_INT_BAT_MON_DET_MASK),
+	/* Battery Mon 3 (Coulomb counter) */
+	REGMAP_IRQ_REG(BD71828_INT_BAT_CC_MON1, 8,
+		       BD71828_INT_BAT_CC_MON1_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_CC_MON2, 8,
+		       BD71828_INT_BAT_CC_MON2_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_CC_MON3, 8,
+		       BD71828_INT_BAT_CC_MON3_MASK),
+	/* Battery Mon 4 */
+	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_CURR_1_RES, 9,
+		       BD71828_INT_BAT_OVER_CURR_1_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_CURR_1_DET, 9,
+		       BD71828_INT_BAT_OVER_CURR_1_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_CURR_2_RES, 9,
+		       BD71828_INT_BAT_OVER_CURR_2_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_CURR_2_DET, 9,
+		       BD71828_INT_BAT_OVER_CURR_2_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_CURR_3_RES, 9,
+		       BD71828_INT_BAT_OVER_CURR_3_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_CURR_3_DET, 9,
+		       BD71828_INT_BAT_OVER_CURR_3_DET_MASK),
+	/* Temperature */
+	REGMAP_IRQ_REG(BD71828_INT_TEMP_BAT_LOW_RES, 10,
+		       BD71828_INT_TEMP_BAT_LOW_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_TEMP_BAT_LOW_DET, 10,
+		       BD71828_INT_TEMP_BAT_LOW_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_TEMP_BAT_HI_RES, 10,
+		       BD71828_INT_TEMP_BAT_HI_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_TEMP_BAT_HI_DET, 10,
+		       BD71828_INT_TEMP_BAT_HI_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_TEMP_CHIP_OVER_125_RES, 10,
+		       BD71828_INT_TEMP_CHIP_OVER_125_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_TEMP_CHIP_OVER_125_DET, 10,
+		       BD71828_INT_TEMP_CHIP_OVER_125_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_TEMP_CHIP_OVER_VF_DET, 10,
+		       BD71828_INT_TEMP_CHIP_OVER_VF_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_TEMP_CHIP_OVER_VF_RES, 10,
+		       BD71828_INT_TEMP_CHIP_OVER_VF_RES_MASK),
+	/* RTC Alarm */
+	REGMAP_IRQ_REG(BD71828_INT_RTC0, 11, BD71828_INT_RTC0_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_RTC1, 11, BD71828_INT_RTC1_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_RTC2, 11, BD71828_INT_RTC2_MASK),
+};
+
+static struct regmap_irq_chip bd71828_irq_chip = {
+	.name = "bd71828_irq",
+	.main_status = BD71828_REG_INT_MAIN,
+	.irqs = &bd71828_irqs[0],
+	.num_irqs = ARRAY_SIZE(bd71828_irqs),
+	.status_base = BD71828_REG_INT_BUCK,
+	.mask_base = BD71828_REG_INT_MASK_BUCK,
+	.ack_base = BD71828_REG_INT_BUCK,
+	.mask_invert = true,
+	.init_ack_masked = true,
+	.num_regs = 12,
+	.num_main_regs = 1,
+	.sub_reg_offsets = &bd71828_sub_irq_offsets[0],
+	.num_main_status_bits = 8,
+	.irq_reg_stride = 1,
+};
+
+static int bd71828_i2c_probe(struct i2c_client *i2c)
+{
+	struct rohm_regmap_dev *chip;
+	struct regmap_irq_chip_data *irq_data;
+	int ret;
+
+	if (!i2c->irq) {
+		dev_err(&i2c->dev, "No IRQ configured\n");
+		return -EINVAL;
+	}
+
+	chip = devm_kzalloc(&i2c->dev, sizeof(*chip), GFP_KERNEL);
+	if (!chip)
+		return -ENOMEM;
+
+	dev_set_drvdata(&i2c->dev, chip);
+
+	chip->regmap = devm_regmap_init_i2c(i2c, &bd71828_regmap);
+	if (IS_ERR(chip->regmap)) {
+		dev_err(&i2c->dev, "Failed to initialize Regmap\n");
+		return PTR_ERR(chip->regmap);
+	}
+
+	ret = devm_regmap_add_irq_chip(&i2c->dev, chip->regmap,
+				       i2c->irq, IRQF_ONESHOT, 0,
+				       &bd71828_irq_chip, &irq_data);
+	if (ret) {
+		dev_err(&i2c->dev, "Failed to add IRQ chip\n");
+		return ret;
+	}
+
+	dev_dbg(&i2c->dev, "Registered %d IRQs for chip\n",
+		bd71828_irq_chip.num_irqs);
+
+	ret = devm_mfd_add_devices(&i2c->dev, PLATFORM_DEVID_AUTO,
+				   bd71828_mfd_cells,
+				   ARRAY_SIZE(bd71828_mfd_cells), NULL, 0,
+				   regmap_irq_get_domain(irq_data));
+	if (ret)
+		dev_err(&i2c->dev, "Failed to create subdevices\n");
+
+	return ret;
+}
+
+static const struct of_device_id bd71828_of_match[] = {
+	{ .compatible = "rohm,bd71828", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, bd71828_of_match);
+
+static struct i2c_driver bd71828_drv = {
+	.driver = {
+		.name = "rohm-bd71828",
+		.of_match_table = bd71828_of_match,
+	},
+	.probe_new = &bd71828_i2c_probe,
+};
+
+module_i2c_driver(bd71828_drv);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("ROHM BD71828 Power Management IC driver");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/mfd/rohm-bd71828.h b/include/linux/mfd/rohm-bd71828.h
new file mode 100644
index 000000000000..eb0557eb5314
--- /dev/null
+++ b/include/linux/mfd/rohm-bd71828.h
@@ -0,0 +1,425 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/* Copyright (C) 2019 ROHM Semiconductors */
+
+#ifndef __LINUX_MFD_BD71828_H__
+#define __LINUX_MFD_BD71828_H__
+
+#include <linux/mfd/rohm-generic.h>
+
+/* Regulator IDs */
+enum {
+	BD71828_BUCK1,
+	BD71828_BUCK2,
+	BD71828_BUCK3,
+	BD71828_BUCK4,
+	BD71828_BUCK5,
+	BD71828_BUCK6,
+	BD71828_BUCK7,
+	BD71828_LDO1,
+	BD71828_LDO2,
+	BD71828_LDO3,
+	BD71828_LDO4,
+	BD71828_LDO5,
+	BD71828_LDO6,
+	BD71828_LDO_SNVS,
+	BD71828_REGULATOR_AMOUNT,
+};
+
+#define BD71828_BUCK1267_VOLTS		0xEF
+#define BD71828_BUCK3_VOLTS		0x10
+#define BD71828_BUCK4_VOLTS		0x20
+#define BD71828_BUCK5_VOLTS		0x10
+#define BD71828_LDO_VOLTS		0x32
+/* LDO6 is fixed 1.8V voltage */
+#define BD71828_LDO_6_VOLTAGE		1800000
+
+/* Registers and masks*/
+
+/* MODE control */
+#define BD71828_REG_PS_CTRL_1		0x04
+#define BD71828_REG_PS_CTRL_2		0x05
+#define BD71828_REG_PS_CTRL_3		0x06
+
+//#define BD71828_REG_SWRESET		0x06
+#define BD71828_MASK_RUN_LVL_CTRL	0x30
+
+/* Regulator control masks */
+
+#define BD71828_MASK_RAMP_DELAY		0x6
+
+#define BD71828_MASK_RUN_EN		0x08
+#define BD71828_MASK_SUSP_EN		0x04
+#define BD71828_MASK_IDLE_EN		0x02
+#define BD71828_MASK_LPSR_EN		0x01
+
+#define BD71828_MASK_RUN0_EN		0x01
+#define BD71828_MASK_RUN1_EN		0x02
+#define BD71828_MASK_RUN2_EN		0x04
+#define BD71828_MASK_RUN3_EN		0x08
+
+#define BD71828_MASK_DVS_BUCK1_CTRL	0x10
+#define BD71828_DVS_BUCK1_CTRL_I2C	0
+#define BD71828_DVS_BUCK1_USE_RUNLVL	0x10
+
+#define BD71828_MASK_DVS_BUCK2_CTRL	0x20
+#define BD71828_DVS_BUCK2_CTRL_I2C	0
+#define BD71828_DVS_BUCK2_USE_RUNLVL	0x20
+
+#define BD71828_MASK_DVS_BUCK6_CTRL	0x40
+#define BD71828_DVS_BUCK6_CTRL_I2C	0
+#define BD71828_DVS_BUCK6_USE_RUNLVL	0x40
+
+#define BD71828_MASK_DVS_BUCK7_CTRL	0x80
+#define BD71828_DVS_BUCK7_CTRL_I2C	0
+#define BD71828_DVS_BUCK7_USE_RUNLVL	0x80
+
+#define BD71828_MASK_BUCK1267_VOLT	0xff
+#define BD71828_MASK_BUCK3_VOLT		0x1f
+#define BD71828_MASK_BUCK4_VOLT		0x3f
+#define BD71828_MASK_BUCK5_VOLT		0x1f
+#define BD71828_MASK_LDO_VOLT		0x3f
+
+/* Regulator control regs */
+#define BD71828_REG_BUCK1_EN		0x08
+#define BD71828_REG_BUCK1_CTRL		0x09
+#define BD71828_REG_BUCK1_MODE		0x0a
+#define BD71828_REG_BUCK1_IDLE_VOLT	0x0b
+#define BD71828_REG_BUCK1_SUSP_VOLT	0x0c
+#define BD71828_REG_BUCK1_VOLT		0x0d
+
+#define BD71828_REG_BUCK2_EN		0x12
+#define BD71828_REG_BUCK2_CTRL		0x13
+#define BD71828_REG_BUCK2_MODE		0x14
+#define BD71828_REG_BUCK2_IDLE_VOLT	0x15
+#define BD71828_REG_BUCK2_SUSP_VOLT	0x16
+#define BD71828_REG_BUCK2_VOLT		0x17
+
+#define BD71828_REG_BUCK3_EN		0x1c
+#define BD71828_REG_BUCK3_MODE		0x1d
+#define BD71828_REG_BUCK3_VOLT		0x1e
+
+#define BD71828_REG_BUCK4_EN		0x1f
+#define BD71828_REG_BUCK4_MODE		0x20
+#define BD71828_REG_BUCK4_VOLT		0x21
+
+#define BD71828_REG_BUCK5_EN		0x22
+#define BD71828_REG_BUCK5_MODE		0x23
+#define BD71828_REG_BUCK5_VOLT		0x24
+
+#define BD71828_REG_BUCK6_EN		0x25
+#define BD71828_REG_BUCK6_CTRL		0x26
+#define BD71828_REG_BUCK6_MODE		0x27
+#define BD71828_REG_BUCK6_IDLE_VOLT	0x28
+#define BD71828_REG_BUCK6_SUSP_VOLT	0x29
+#define BD71828_REG_BUCK6_VOLT		0x2a
+
+#define BD71828_REG_BUCK7_EN		0x2f
+#define BD71828_REG_BUCK7_CTRL		0x30
+#define BD71828_REG_BUCK7_MODE		0x31
+#define BD71828_REG_BUCK7_IDLE_VOLT	0x32
+#define BD71828_REG_BUCK7_SUSP_VOLT	0x33
+#define BD71828_REG_BUCK7_VOLT		0x34
+
+#define BD71828_REG_LDO1_EN		0x39
+#define BD71828_REG_LDO1_VOLT		0x3a
+#define BD71828_REG_LDO2_EN		0x3b
+#define BD71828_REG_LDO2_VOLT		0x3c
+#define BD71828_REG_LDO3_EN		0x3d
+#define BD71828_REG_LDO3_VOLT		0x3e
+#define BD71828_REG_LDO4_EN		0x3f
+#define BD71828_REG_LDO4_VOLT		0x40
+#define BD71828_REG_LDO5_EN		0x41
+#define BD71828_REG_LDO5_VOLT		0x43
+#define BD71828_REG_LDO5_VOLT_OPT	0x42
+#define BD71828_REG_LDO6_EN		0x44
+//#define BD71828_REG_LDO6_VOLT		0x4
+#define BD71828_REG_LDO7_EN		0x45
+#define BD71828_REG_LDO7_VOLT		0x46
+
+/* GPIO */
+
+#define BD71828_GPIO_DRIVE_MASK		0x2
+#define BD71828_GPIO_OPEN_DRAIN		0x0
+#define BD71828_GPIO_PUSH_PULL		0x2
+#define BD71828_GPIO_OUT_HI		0x1
+#define BD71828_GPIO_OUT_LO		0x0
+#define BD71828_GPIO_OUT_MASK		0x1
+
+#define BD71828_REG_GPIO_CTRL1		0x47
+#define BD71828_REG_GPIO_CTRL2		0x48
+#define BD71828_REG_GPIO_CTRL3		0x49
+#define BD71828_REG_IO_STAT		0xed
+
+/* RTC */
+#define BD71828_REG_RTC_SEC		0x4c
+#define BD71828_REG_RTC_MINUTE		0x4d
+#define BD71828_REG_RTC_HOUR		0x4e
+#define BD71828_REG_RTC_WEEK		0x4f
+#define BD71828_REG_RTC_DAY		0x50
+#define BD71828_REG_RTC_MONTH		0x51
+#define BD71828_REG_RTC_YEAR		0x52
+
+#define BD71828_REG_RTC_ALM0_SEC	0x53
+#define BD71828_REG_RTC_ALM0_MINUTE	0x54
+#define BD71828_REG_RTC_ALM0_HOUR	0x55
+#define BD71828_REG_RTC_ALM0_WEEK	0x56
+#define BD71828_REG_RTC_ALM0_DAY	0x57
+#define BD71828_REG_RTC_ALM0_MONTH	0x58
+#define BD71828_REG_RTC_ALM0_YEAR	0x59
+#define BD71828_REG_RTC_ALM0_MASK	0x61
+
+#define BD71828_REG_RTC_ALM1_SEC	0x5a
+#define BD71828_REG_RTC_ALM1_MINUTE	0x5b
+#define BD71828_REG_RTC_ALM1_HOUR	0x5c
+#define BD71828_REG_RTC_ALM1_WEEK	0x5d
+#define BD71828_REG_RTC_ALM1_DAY	0x5e
+#define BD71828_REG_RTC_ALM1_MONTH	0x5f
+#define BD71828_REG_RTC_ALM1_YEAR	0x60
+#define BD71828_REG_RTC_ALM1_MASK	0x62
+
+#define BD71828_REG_RTC_ALM2		0x63
+
+/* Charger/Battey */
+#define BD71828_REG_CHG_STATE		0x65
+#define BD71828_REG_CHG_FULL		0xd2
+
+/* CLK */
+#define BD71828_REG_OUT32K		0x4B
+
+/* LEDs */
+#define BD71828_REG_LED_CTRL		0x4A
+#define BD71828_MASK_LED_AMBER		0x80
+#define BD71828_MASK_LED_GREEN		0x40
+#define BD71828_LED_ON			0xff
+#define BD71828_LED_OFF			0x0
+
+/* IRQ registers */
+#define BD71828_REG_INT_MASK_BUCK	0xd3
+#define BD71828_REG_INT_MASK_DCIN1	0xd4
+#define BD71828_REG_INT_MASK_DCIN2	0xd5
+#define BD71828_REG_INT_MASK_VSYS	0xd6
+#define BD71828_REG_INT_MASK_CHG	0xd7
+#define BD71828_REG_INT_MASK_BAT	0xd8
+#define BD71828_REG_INT_MASK_BAT_MON1	0xd9
+#define BD71828_REG_INT_MASK_BAT_MON2	0xda
+#define BD71828_REG_INT_MASK_BAT_MON3	0xdb
+#define BD71828_REG_INT_MASK_BAT_MON4	0xdc
+#define BD71828_REG_INT_MASK_TEMP	0xdd
+#define BD71828_REG_INT_MASK_RTC	0xde
+
+
+#define BD71828_REG_INT_MAIN		0xdf
+#define BD71828_REG_INT_BUCK		0xe0
+#define BD71828_REG_INT_DCIN1		0xe1
+#define BD71828_REG_INT_DCIN2		0xe2
+#define BD71828_REG_INT_VSYS		0xe3
+#define BD71828_REG_INT_CHG		0xe4
+#define BD71828_REG_INT_BAT		0xe5
+#define BD71828_REG_INT_BAT_MON1	0xe6
+#define BD71828_REG_INT_BAT_MON2	0xe7
+#define BD71828_REG_INT_BAT_MON3	0xe8
+#define BD71828_REG_INT_BAT_MON4	0xe9
+#define BD71828_REG_INT_TEMP		0xea
+#define BD71828_REG_INT_RTC		0xeb
+#define BD71828_REG_INT_UPDATE		0xec
+
+#define BD71828_MAX_REGISTER BD71828_REG_IO_STAT
+
+/* Masks for main IRQ register bits */
+enum {
+	BD71828_INT_BUCK,
+#define BD71828_INT_BUCK_MASK BIT(BD71828_INT_BUCK)
+	BD71828_INT_DCIN,
+#define BD71828_INT_DCIN_MASK BIT(BD71828_INT_DCIN)
+	BD71828_INT_VSYS,
+#define BD71828_INT_VSYS_MASK BIT(BD71828_INT_VSYS)
+	BD71828_INT_CHG,
+#define BD71828_INT_CHG_MASK BIT(BD71828_INT_CHG)
+	BD71828_INT_BAT,
+#define BD71828_INT_BAT_MASK BIT(BD71828_INT_BAT)
+	BD71828_INT_BAT_MON,
+#define BD71828_INT_BAT_MON_MASK BIT(BD71828_INT_BAT_MON)
+	BD71828_INT_TEMP,
+#define BD71828_INT_TEMP_MASK BIT(BD71828_INT_TEMP)
+	BD71828_INT_RTC,
+#define BD71828_INT_RTC_MASK BIT(BD71828_INT_RTC)
+};
+
+/* Interrupts */
+enum {
+	/* BUCK reg interrupts */
+	BD71828_INT_BUCK1_OCP,
+	BD71828_INT_BUCK2_OCP,
+	BD71828_INT_BUCK3_OCP,
+	BD71828_INT_BUCK4_OCP,
+	BD71828_INT_BUCK5_OCP,
+	BD71828_INT_BUCK6_OCP,
+	BD71828_INT_BUCK7_OCP,
+	BD71828_INT_PGFAULT,
+	/* DCIN1 interrupts */
+	BD71828_INT_DCIN_DET,
+	BD71828_INT_DCIN_RMV,
+	BD71828_INT_CLPS_OUT,
+	BD71828_INT_CLPS_IN,
+	/* DCIN2 interrupts */
+	BD71828_INT_DCIN_MON_RES,
+	BD71828_INT_DCIN_MON_DET,
+	BD71828_INT_LONGPUSH,
+	BD71828_INT_MIDPUSH,
+	BD71828_INT_SHORTPUSH,
+	BD71828_INT_PUSH,
+	BD71828_INT_WDOG,
+	BD71828_INT_SWRESET,
+	/* Vsys */
+	BD71828_INT_VSYS_UV_RES,
+	BD71828_INT_VSYS_UV_DET,
+	BD71828_INT_VSYS_LOW_RES,
+	BD71828_INT_VSYS_LOW_DET,
+	BD71828_INT_VSYS_HALL_IN,
+	BD71828_INT_VSYS_HALL_TOGGLE,
+	BD71828_INT_VSYS_MON_RES,
+	BD71828_INT_VSYS_MON_DET,
+	/* Charger */
+	BD71828_INT_CHG_DCIN_ILIM,
+	BD71828_INT_CHG_TOPOFF_TO_DONE,
+	BD71828_INT_CHG_WDG_TEMP,
+	BD71828_INT_CHG_WDG_TIME,
+	BD71828_INT_CHG_RECHARGE_RES,
+	BD71828_INT_CHG_RECHARGE_DET,
+	BD71828_INT_CHG_RANGED_TEMP_TRANSITION,
+	BD71828_INT_CHG_STATE_TRANSITION,
+	/* Battery */
+	BD71828_INT_BAT_TEMP_NORMAL,
+	BD71828_INT_BAT_TEMP_ERANGE,
+	BD71828_INT_BAT_TEMP_WARN,
+	BD71828_INT_BAT_REMOVED,
+	BD71828_INT_BAT_DETECTED,
+	BD71828_INT_THERM_REMOVED,
+	BD71828_INT_THERM_DETECTED,
+	/* Battery Mon 1 */
+	BD71828_INT_BAT_DEAD,
+	BD71828_INT_BAT_SHORTC_RES,
+	BD71828_INT_BAT_SHORTC_DET,
+	BD71828_INT_BAT_LOW_VOLT_RES,
+	BD71828_INT_BAT_LOW_VOLT_DET,
+	BD71828_INT_BAT_OVER_VOLT_RES,
+	BD71828_INT_BAT_OVER_VOLT_DET,
+	/* Battery Mon 2 */
+	BD71828_INT_BAT_MON_RES,
+	BD71828_INT_BAT_MON_DET,
+	/* Battery Mon 3 (Coulomb counter) */
+	BD71828_INT_BAT_CC_MON1,
+	BD71828_INT_BAT_CC_MON2,
+	BD71828_INT_BAT_CC_MON3,
+	/* Battery Mon 4 */
+	BD71828_INT_BAT_OVER_CURR_1_RES,
+	BD71828_INT_BAT_OVER_CURR_1_DET,
+	BD71828_INT_BAT_OVER_CURR_2_RES,
+	BD71828_INT_BAT_OVER_CURR_2_DET,
+	BD71828_INT_BAT_OVER_CURR_3_RES,
+	BD71828_INT_BAT_OVER_CURR_3_DET,
+	/* Temperature */
+	BD71828_INT_TEMP_BAT_LOW_RES,
+	BD71828_INT_TEMP_BAT_LOW_DET,
+	BD71828_INT_TEMP_BAT_HI_RES,
+	BD71828_INT_TEMP_BAT_HI_DET,
+	BD71828_INT_TEMP_CHIP_OVER_125_RES,
+	BD71828_INT_TEMP_CHIP_OVER_125_DET,
+	BD71828_INT_TEMP_CHIP_OVER_VF_DET,
+	BD71828_INT_TEMP_CHIP_OVER_VF_RES,
+	/* RTC Alarm */
+	BD71828_INT_RTC0,
+	BD71828_INT_RTC1,
+	BD71828_INT_RTC2,
+};
+
+#define BD71828_INT_BUCK1_OCP_MASK			0x1
+#define BD71828_INT_BUCK2_OCP_MASK			0x2
+#define BD71828_INT_BUCK3_OCP_MASK			0x4
+#define BD71828_INT_BUCK4_OCP_MASK			0x8
+#define BD71828_INT_BUCK5_OCP_MASK			0x10
+#define BD71828_INT_BUCK6_OCP_MASK			0x20
+#define BD71828_INT_BUCK7_OCP_MASK			0x40
+#define BD71828_INT_PGFAULT_MASK			0x80
+
+#define BD71828_INT_DCIN_DET_MASK			0x1
+#define BD71828_INT_DCIN_RMV_MASK			0x2
+#define BD71828_INT_CLPS_OUT_MASK			0x4
+#define BD71828_INT_CLPS_IN_MASK			0x8
+	/* DCIN2 interrupts */
+#define BD71828_INT_DCIN_MON_RES_MASK			0x1
+#define BD71828_INT_DCIN_MON_DET_MASK			0x2
+#define BD71828_INT_LONGPUSH_MASK			0x4
+#define BD71828_INT_MIDPUSH_MASK			0x8
+#define BD71828_INT_SHORTPUSH_MASK			0x10
+#define BD71828_INT_PUSH_MASK				0x20
+#define BD71828_INT_WDOG_MASK				0x40
+#define BD71828_INT_SWRESET_MASK			0x80
+	/* Vsys */
+#define BD71828_INT_VSYS_UV_RES_MASK			0x1
+#define BD71828_INT_VSYS_UV_DET_MASK			0x2
+#define BD71828_INT_VSYS_LOW_RES_MASK			0x4
+#define BD71828_INT_VSYS_LOW_DET_MASK			0x8
+#define BD71828_INT_VSYS_HALL_IN_MASK			0x10
+#define BD71828_INT_VSYS_HALL_TOGGLE_MASK		0x20
+#define BD71828_INT_VSYS_MON_RES_MASK			0x40
+#define BD71828_INT_VSYS_MON_DET_MASK			0x80
+	/* Charger */
+#define BD71828_INT_CHG_DCIN_ILIM_MASK			0x1
+#define BD71828_INT_CHG_TOPOFF_TO_DONE_MASK		0x2
+#define BD71828_INT_CHG_WDG_TEMP_MASK			0x4
+#define BD71828_INT_CHG_WDG_TIME_MASK			0x8
+#define BD71828_INT_CHG_RECHARGE_RES_MASK		0x10
+#define BD71828_INT_CHG_RECHARGE_DET_MASK		0x20
+#define BD71828_INT_CHG_RANGED_TEMP_TRANSITION_MASK	0x40
+#define BD71828_INT_CHG_STATE_TRANSITION_MASK		0x80
+	/* Battery */
+#define BD71828_INT_BAT_TEMP_NORMAL_MASK		0x1
+#define BD71828_INT_BAT_TEMP_ERANGE_MASK		0x2
+#define BD71828_INT_BAT_TEMP_WARN_MASK			0x4
+#define BD71828_INT_BAT_REMOVED_MASK			0x10
+#define BD71828_INT_BAT_DETECTED_MASK			0x20
+#define BD71828_INT_THERM_REMOVED_MASK			0x40
+#define BD71828_INT_THERM_DETECTED_MASK			0x80
+	/* Battery Mon 1 */
+#define BD71828_INT_BAT_DEAD_MASK			0x2
+#define BD71828_INT_BAT_SHORTC_RES_MASK			0x4
+#define BD71828_INT_BAT_SHORTC_DET_MASK			0x8
+#define BD71828_INT_BAT_LOW_VOLT_RES_MASK		0x10
+#define BD71828_INT_BAT_LOW_VOLT_DET_MASK		0x20
+#define BD71828_INT_BAT_OVER_VOLT_RES_MASK		0x40
+#define BD71828_INT_BAT_OVER_VOLT_DET_MASK		0x80
+	/* Battery Mon 2 */
+#define BD71828_INT_BAT_MON_RES_MASK			0x1
+#define BD71828_INT_BAT_MON_DET_MASK			0x2
+	/* Battery Mon 3 (Coulomb counter) */
+#define BD71828_INT_BAT_CC_MON1_MASK			0x1
+#define BD71828_INT_BAT_CC_MON2_MASK			0x2
+#define BD71828_INT_BAT_CC_MON3_MASK			0x4
+	/* Battery Mon 4 */
+#define BD71828_INT_BAT_OVER_CURR_1_RES_MASK		0x1
+#define BD71828_INT_BAT_OVER_CURR_1_DET_MASK		0x2
+#define BD71828_INT_BAT_OVER_CURR_2_RES_MASK		0x4
+#define BD71828_INT_BAT_OVER_CURR_2_DET_MASK		0x8
+#define BD71828_INT_BAT_OVER_CURR_3_RES_MASK		0x10
+#define BD71828_INT_BAT_OVER_CURR_3_DET_MASK		0x20
+	/* Temperature */
+#define BD71828_INT_TEMP_BAT_LOW_RES_MASK		0x1
+#define BD71828_INT_TEMP_BAT_LOW_DET_MASK		0x2
+#define BD71828_INT_TEMP_BAT_HI_RES_MASK		0x4
+#define BD71828_INT_TEMP_BAT_HI_DET_MASK		0x8
+#define BD71828_INT_TEMP_CHIP_OVER_125_RES_MASK		0x10
+#define BD71828_INT_TEMP_CHIP_OVER_125_DET_MASK		0x20
+#define BD71828_INT_TEMP_CHIP_OVER_VF_RES_MASK		0x40
+#define BD71828_INT_TEMP_CHIP_OVER_VF_DET_MASK		0x80
+	/* RTC Alarm */
+#define BD71828_INT_RTC0_MASK				0x1
+#define BD71828_INT_RTC1_MASK				0x2
+#define BD71828_INT_RTC2_MASK				0x4
+
+#define BD71828_OUT32K_EN				0x1
+#define BD71828_OUT_TYPE_MASK				0x2
+#define BD71828_OUT_TYPE_OPEN_DRAIN			0x0
+#define BD71828_OUT_TYPE_CMOS				0x2
+
+#endif /* __LINUX_MFD_BD71828_H__ */
diff --git a/include/linux/mfd/rohm-generic.h b/include/linux/mfd/rohm-generic.h
index 922f88008232..ff3dd7578fd3 100644
--- a/include/linux/mfd/rohm-generic.h
+++ b/include/linux/mfd/rohm-generic.h
@@ -8,6 +8,7 @@ enum rohm_chip_type {
 	ROHM_CHIP_TYPE_BD71837 = 0,
 	ROHM_CHIP_TYPE_BD71847,
 	ROHM_CHIP_TYPE_BD70528,
+	ROHM_CHIP_TYPE_BD71828,
 	ROHM_CHIP_TYPE_AMOUNT
 };
 
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply related	[flat|nested] 19+ messages in thread

* [PATCH v4 06/16] mfd: input: bd71828: Add power-key support
  2019-11-16 18:55 [PATCH v4 00/16] Support ROHM BD71828 PMIC Matti Vaittinen
                   ` (4 preceding siblings ...)
  2019-11-16 18:57 ` [PATCH v4 05/16] mfd: bd71828: Support ROHM BD71828 PMIC - core Matti Vaittinen
@ 2019-11-16 18:58 ` Matti Vaittinen
  2019-11-16 18:58 ` [PATCH v4 07/16] clk: bd718x7: Support ROHM BD71828 clk block Matti Vaittinen
                   ` (9 subsequent siblings)
  15 siblings, 0 replies; 19+ messages in thread
From: Matti Vaittinen @ 2019-11-16 18:58 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Lee Jones, Jacek Anaszewski, Pavel Machek, Dan Murphy,
	Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Mauro Carvalho Chehab, Jeff Kirsher, Wolfram Sang,
	Marek Szyprowski, Heiner Kallweit, Nicholas Mc Guire,
	Phil Edworthy, linux-leds, devicetree, linux-kernel, linux-doc,
	linux-clk, linux-gpio, linux-rtc

Use gpio_keys to send power input-event to user-space when power
button (short) press is detected.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
---
 drivers/mfd/rohm-bd71828.c | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/drivers/mfd/rohm-bd71828.c b/drivers/mfd/rohm-bd71828.c
index 7f445d699fd9..b892b50ec555 100644
--- a/drivers/mfd/rohm-bd71828.c
+++ b/drivers/mfd/rohm-bd71828.c
@@ -4,7 +4,9 @@
 //
 // ROHM BD71828 PMIC driver
 
+#include <linux/gpio_keys.h>
 #include <linux/i2c.h>
+#include <linux/input.h>
 #include <linux/interrupt.h>
 #include <linux/ioport.h>
 #include <linux/irq.h>
@@ -15,6 +17,18 @@
 #include <linux/regmap.h>
 #include <linux/types.h>
 
+static struct gpio_keys_button button = {
+	.code = KEY_POWER,
+	.gpio = -1,
+	.type = EV_KEY,
+};
+
+static struct gpio_keys_platform_data bd71828_powerkey_data = {
+	.buttons = &button,
+	.nbuttons = 1,
+	.name = "bd71828-pwrkey",
+};
+
 static const struct resource rtc_irqs[] = {
 	DEFINE_RES_IRQ_NAMED(BD71828_INT_RTC0, "bd71828-rtc-alm-0"),
 	DEFINE_RES_IRQ_NAMED(BD71828_INT_RTC1, "bd71828-rtc-alm-1"),
@@ -35,6 +49,10 @@ static struct mfd_cell bd71828_mfd_cells[] = {
 		.name = "bd71828-rtc",
 		.resources = rtc_irqs,
 		.num_resources = ARRAY_SIZE(rtc_irqs),
+	}, {
+		.name = "gpio-keys",
+		.platform_data = &bd71828_powerkey_data,
+		.pdata_size = sizeof(bd71828_powerkey_data),
 	},
 };
 
@@ -288,6 +306,14 @@ static int bd71828_i2c_probe(struct i2c_client *i2c)
 	dev_dbg(&i2c->dev, "Registered %d IRQs for chip\n",
 		bd71828_irq_chip.num_irqs);
 
+	ret = regmap_irq_get_virq(irq_data, BD71828_INT_SHORTPUSH);
+	if (ret < 0) {
+		dev_err(&i2c->dev, "Failed to get the power-key IRQ\n");
+		return ret;
+	}
+
+	button.irq = ret;
+
 	ret = devm_mfd_add_devices(&i2c->dev, PLATFORM_DEVID_AUTO,
 				   bd71828_mfd_cells,
 				   ARRAY_SIZE(bd71828_mfd_cells), NULL, 0,
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply related	[flat|nested] 19+ messages in thread

* [PATCH v4 07/16] clk: bd718x7: Support ROHM BD71828 clk block
  2019-11-16 18:55 [PATCH v4 00/16] Support ROHM BD71828 PMIC Matti Vaittinen
                   ` (5 preceding siblings ...)
  2019-11-16 18:58 ` [PATCH v4 06/16] mfd: input: bd71828: Add power-key support Matti Vaittinen
@ 2019-11-16 18:58 ` Matti Vaittinen
  2019-11-16 18:59 ` [PATCH v4 08/16] regulator: bd718x7: Split driver to common and bd718x7 specific parts Matti Vaittinen
                   ` (8 subsequent siblings)
  15 siblings, 0 replies; 19+ messages in thread
From: Matti Vaittinen @ 2019-11-16 18:58 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Lee Jones, Jacek Anaszewski, Pavel Machek, Dan Murphy,
	Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Mauro Carvalho Chehab, Jeff Kirsher, Wolfram Sang,
	Marek Szyprowski, Heiner Kallweit, Nicholas Mc Guire,
	Phil Edworthy, linux-leds, devicetree, linux-kernel, linux-doc,
	linux-clk, linux-gpio, linux-rtc

BD71828GW is a single-chip power management IC for battery-powered portable
devices. Add support for controlling BD71828 clk using bd718x7 driver.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
 drivers/clk/Kconfig              |  6 ++---
 drivers/clk/clk-bd718x7.c        | 38 +++++++++++++++++++++++---------
 include/linux/mfd/rohm-bd70528.h |  6 -----
 include/linux/mfd/rohm-bd71828.h |  4 ----
 include/linux/mfd/rohm-bd718x7.h |  6 -----
 5 files changed, 31 insertions(+), 29 deletions(-)

diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index c44247d0b83e..71c5dfdc78f4 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -293,10 +293,10 @@ config COMMON_CLK_STM32H7
 	  Support for stm32h7 SoC family clocks
 
 config COMMON_CLK_BD718XX
-	tristate "Clock driver for ROHM BD718x7 PMIC"
-	depends on MFD_ROHM_BD718XX || MFD_ROHM_BD70528
+	tristate "Clock driver for 32K clk gates on ROHM PMICs"
+	depends on MFD_ROHM_BD718XX || MFD_ROHM_BD70528 || MFD_ROHM_BD71828
 	help
-	  This driver supports ROHM BD71837, ROHM BD71847 and
+	  This driver supports ROHM BD71837, ROHM BD71847, ROHM BD71828 and
 	  ROHM BD70528 PMICs clock gates.
 
 config COMMON_CLK_FIXED_MMIO
diff --git a/drivers/clk/clk-bd718x7.c b/drivers/clk/clk-bd718x7.c
index 1c1764f74d0a..853f484b758a 100644
--- a/drivers/clk/clk-bd718x7.c
+++ b/drivers/clk/clk-bd718x7.c
@@ -7,12 +7,25 @@
 #include <linux/err.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
-#include <linux/mfd/rohm-bd718x7.h>
-#include <linux/mfd/rohm-bd70528.h>
+#include <linux/mfd/rohm-generic.h>
 #include <linux/clk-provider.h>
 #include <linux/clkdev.h>
 #include <linux/regmap.h>
 
+/* clk control registers */
+/* BD70528 */
+#define BD70528_REG_OUT32K	0x2c
+/* BD71828 */
+#define BD71828_REG_OUT32K	0x4B
+/* BD71837 and BD71847 */
+#define BD718XX_REG_OUT32K	0x2E
+
+/*
+ * BD71837, BD71847, BD70528 and BD71828 all use bit [0] to clk output control
+ */
+#define CLK_OUT_EN_MASK		BIT(0)
+
+
 struct bd718xx_clk {
 	struct clk_hw hw;
 	u8 reg;
@@ -21,10 +34,8 @@ struct bd718xx_clk {
 	struct rohm_regmap_dev *mfd;
 };
 
-static int bd71837_clk_set(struct clk_hw *hw, int status)
+static int bd71837_clk_set(struct bd718xx_clk *c, unsigned int status)
 {
-	struct bd718xx_clk *c = container_of(hw, struct bd718xx_clk, hw);
-
 	return regmap_update_bits(c->mfd->regmap, c->reg, c->mask, status);
 }
 
@@ -33,14 +44,16 @@ static void bd71837_clk_disable(struct clk_hw *hw)
 	int rv;
 	struct bd718xx_clk *c = container_of(hw, struct bd718xx_clk, hw);
 
-	rv = bd71837_clk_set(hw, 0);
+	rv = bd71837_clk_set(c, 0);
 	if (rv)
 		dev_dbg(&c->pdev->dev, "Failed to disable 32K clk (%d)\n", rv);
 }
 
 static int bd71837_clk_enable(struct clk_hw *hw)
 {
-	return bd71837_clk_set(hw, 1);
+	struct bd718xx_clk *c = container_of(hw, struct bd718xx_clk, hw);
+
+	return bd71837_clk_set(c, 0xffffffff);
 }
 
 static int bd71837_clk_is_enabled(struct clk_hw *hw)
@@ -92,11 +105,15 @@ static int bd71837_clk_probe(struct platform_device *pdev)
 	case ROHM_CHIP_TYPE_BD71837:
 	case ROHM_CHIP_TYPE_BD71847:
 		c->reg = BD718XX_REG_OUT32K;
-		c->mask = BD718XX_OUT32K_EN;
+		c->mask = CLK_OUT_EN_MASK;
+		break;
+	case ROHM_CHIP_TYPE_BD71828:
+		c->reg = BD71828_REG_OUT32K;
+		c->mask = CLK_OUT_EN_MASK;
 		break;
 	case ROHM_CHIP_TYPE_BD70528:
-		c->reg = BD70528_REG_CLK_OUT;
-		c->mask = BD70528_CLK_OUT_EN_MASK;
+		c->reg = BD70528_REG_OUT32K;
+		c->mask = CLK_OUT_EN_MASK;
 		break;
 	default:
 		dev_err(&pdev->dev, "Unknown clk chip\n");
@@ -126,6 +143,7 @@ static const struct platform_device_id bd718x7_clk_id[] = {
 	{ "bd71837-clk", ROHM_CHIP_TYPE_BD71837 },
 	{ "bd71847-clk", ROHM_CHIP_TYPE_BD71847 },
 	{ "bd70528-clk", ROHM_CHIP_TYPE_BD70528 },
+	{ "bd71828-clk", ROHM_CHIP_TYPE_BD71828 },
 	{ },
 };
 MODULE_DEVICE_TABLE(platform, bd718x7_clk_id);
diff --git a/include/linux/mfd/rohm-bd70528.h b/include/linux/mfd/rohm-bd70528.h
index 1013e60c5b25..2ad2320d0a96 100644
--- a/include/linux/mfd/rohm-bd70528.h
+++ b/include/linux/mfd/rohm-bd70528.h
@@ -89,10 +89,6 @@ struct bd70528_data {
 #define BD70528_REG_GPIO3_OUT	0x52
 #define BD70528_REG_GPIO4_OUT	0x54
 
-/* clk control */
-
-#define BD70528_REG_CLK_OUT	0x2c
-
 /* RTC */
 
 #define BD70528_REG_RTC_COUNT_H		0x2d
@@ -309,8 +305,6 @@ enum {
 
 #define BD70528_GPIO_IN_STATE_BASE 1
 
-#define BD70528_CLK_OUT_EN_MASK 0x1
-
 /* RTC masks to mask out reserved bits */
 
 #define BD70528_MASK_RTC_SEC		0x7f
diff --git a/include/linux/mfd/rohm-bd71828.h b/include/linux/mfd/rohm-bd71828.h
index eb0557eb5314..d013e03f742d 100644
--- a/include/linux/mfd/rohm-bd71828.h
+++ b/include/linux/mfd/rohm-bd71828.h
@@ -183,9 +183,6 @@ enum {
 #define BD71828_REG_CHG_STATE		0x65
 #define BD71828_REG_CHG_FULL		0xd2
 
-/* CLK */
-#define BD71828_REG_OUT32K		0x4B
-
 /* LEDs */
 #define BD71828_REG_LED_CTRL		0x4A
 #define BD71828_MASK_LED_AMBER		0x80
@@ -417,7 +414,6 @@ enum {
 #define BD71828_INT_RTC1_MASK				0x2
 #define BD71828_INT_RTC2_MASK				0x4
 
-#define BD71828_OUT32K_EN				0x1
 #define BD71828_OUT_TYPE_MASK				0x2
 #define BD71828_OUT_TYPE_OPEN_DRAIN			0x0
 #define BD71828_OUT_TYPE_CMOS				0x2
diff --git a/include/linux/mfd/rohm-bd718x7.h b/include/linux/mfd/rohm-bd718x7.h
index 7f2dbde402a1..bee2474a8f9f 100644
--- a/include/linux/mfd/rohm-bd718x7.h
+++ b/include/linux/mfd/rohm-bd718x7.h
@@ -191,12 +191,6 @@ enum {
 #define IRQ_ON_REQ		0x02
 #define IRQ_STBY_REQ		0x01
 
-/* BD718XX_REG_OUT32K bits */
-#define BD718XX_OUT32K_EN	0x01
-
-/* BD7183XX gated clock rate */
-#define BD718XX_CLK_RATE 32768
-
 /* ROHM BD718XX irqs */
 enum {
 	BD718XX_INT_STBY_REQ,
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply related	[flat|nested] 19+ messages in thread

* [PATCH v4 08/16] regulator: bd718x7: Split driver to common and bd718x7 specific parts
  2019-11-16 18:55 [PATCH v4 00/16] Support ROHM BD71828 PMIC Matti Vaittinen
                   ` (6 preceding siblings ...)
  2019-11-16 18:58 ` [PATCH v4 07/16] clk: bd718x7: Support ROHM BD71828 clk block Matti Vaittinen
@ 2019-11-16 18:59 ` Matti Vaittinen
  2019-11-16 18:59 ` [PATCH v4 09/16] regulator: bd71828: Basic support for ROHM bd71828 PMIC regulators Matti Vaittinen
                   ` (7 subsequent siblings)
  15 siblings, 0 replies; 19+ messages in thread
From: Matti Vaittinen @ 2019-11-16 18:59 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Lee Jones, Jacek Anaszewski, Pavel Machek, Dan Murphy,
	Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Mauro Carvalho Chehab, Jeff Kirsher, Wolfram Sang,
	Marek Szyprowski, Heiner Kallweit, Nicholas Mc Guire,
	Phil Edworthy, linux-leds, devicetree, linux-kernel, linux-doc,
	linux-clk, linux-gpio, linux-rtc

Few ROHM PMICs allow setting the voltage states for different system states
like RUN, IDLE, SUSPEND and LPSR. States are then changed via SoC specific
mechanisms. bd718x7 driver implemented device-tree parsing functions for
these state specific voltages. The parsing functions can be re-used by
other ROHM chip drivers like bd71828. Split the generic functions from
bd718x7-regulator.c to rohm-regulator.c and export them for other modules
to use.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
 drivers/regulator/Kconfig             |   4 +
 drivers/regulator/Makefile            |   1 +
 drivers/regulator/bd718x7-regulator.c | 183 ++++++++------------------
 drivers/regulator/rohm-regulator.c    |  95 +++++++++++++
 include/linux/mfd/rohm-generic.h      |  44 +++++++
 5 files changed, 199 insertions(+), 128 deletions(-)
 create mode 100644 drivers/regulator/rohm-regulator.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 3ee63531f6d5..5182a3d5660c 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -197,6 +197,7 @@ config REGULATOR_BD70528
 config REGULATOR_BD718XX
 	tristate "ROHM BD71837 Power Regulator"
 	depends on MFD_ROHM_BD718XX
+	select REGULATOR_ROHM
 	help
 	  This driver supports voltage regulators on ROHM BD71837 PMIC.
 	  This will enable support for the software controllable buck
@@ -790,6 +791,9 @@ config REGULATOR_RN5T618
 	  Say y here to support the regulators found on Ricoh RN5T567,
 	  RN5T618 or RC5T619 PMIC.
 
+config REGULATOR_ROHM
+	tristate
+
 config REGULATOR_RT5033
 	tristate "Richtek RT5033 Regulators"
 	depends on MFD_RT5033
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 2210ba56f9bd..6bcab72c1fc7 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -99,6 +99,7 @@ obj-$(CONFIG_REGULATOR_PCF50633) += pcf50633-regulator.o
 obj-$(CONFIG_REGULATOR_RC5T583)  += rc5t583-regulator.o
 obj-$(CONFIG_REGULATOR_RK808)   += rk808-regulator.o
 obj-$(CONFIG_REGULATOR_RN5T618) += rn5t618-regulator.o
+obj-$(CONFIG_REGULATOR_ROHM)	+= rohm-regulator.o
 obj-$(CONFIG_REGULATOR_RT5033)	+= rt5033-regulator.o
 obj-$(CONFIG_REGULATOR_S2MPA01) += s2mpa01.o
 obj-$(CONFIG_REGULATOR_S2MPS11) += s2mps11.o
diff --git a/drivers/regulator/bd718x7-regulator.c b/drivers/regulator/bd718x7-regulator.c
index 2058d972c7b7..76aef64cf793 100644
--- a/drivers/regulator/bd718x7-regulator.c
+++ b/drivers/regulator/bd718x7-regulator.c
@@ -318,6 +318,7 @@ struct reg_init {
 };
 struct bd718xx_regulator_data {
 	struct regulator_desc desc;
+	const struct rohm_dvs_config dvs;
 	const struct reg_init init;
 	const struct reg_init *additional_inits;
 	int additional_init_amnt;
@@ -349,133 +350,15 @@ static const struct reg_init bd71837_ldo6_inits[] = {
 	},
 };
 
-#define NUM_DVS_BUCKS 4
-
-struct of_dvs_setting {
-	const char *prop;
-	unsigned int reg;
-};
-
-static int set_dvs_levels(const struct of_dvs_setting *dvs,
-			  struct device_node *np,
-			  const struct regulator_desc *desc,
-			  struct regmap *regmap)
-{
-	int ret, i;
-	unsigned int uv;
-
-	ret = of_property_read_u32(np, dvs->prop, &uv);
-	if (ret) {
-		if (ret != -EINVAL)
-			return ret;
-		return 0;
-	}
-
-	for (i = 0; i < desc->n_voltages; i++) {
-		ret = regulator_desc_list_voltage_linear_range(desc, i);
-		if (ret < 0)
-			continue;
-		if (ret == uv) {
-			i <<= ffs(desc->vsel_mask) - 1;
-			ret = regmap_update_bits(regmap, dvs->reg,
-						 DVS_BUCK_RUN_MASK, i);
-			break;
-		}
-	}
-	return ret;
-}
-
-static int buck4_set_hw_dvs_levels(struct device_node *np,
+static int buck_set_hw_dvs_levels(struct device_node *np,
 			    const struct regulator_desc *desc,
 			    struct regulator_config *cfg)
 {
-	int ret, i;
-	const struct of_dvs_setting dvs[] = {
-		{
-			.prop = "rohm,dvs-run-voltage",
-			.reg = BD71837_REG_BUCK4_VOLT_RUN,
-		},
-	};
+	struct bd718xx_regulator_data *data;
 
-	for (i = 0; i < ARRAY_SIZE(dvs); i++) {
-		ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap);
-		if (ret)
-			break;
-	}
-	return ret;
-}
-static int buck3_set_hw_dvs_levels(struct device_node *np,
-			    const struct regulator_desc *desc,
-			    struct regulator_config *cfg)
-{
-	int ret, i;
-	const struct of_dvs_setting dvs[] = {
-		{
-			.prop = "rohm,dvs-run-voltage",
-			.reg = BD71837_REG_BUCK3_VOLT_RUN,
-		},
-	};
+	data = container_of(desc, struct bd718xx_regulator_data, desc);
 
-	for (i = 0; i < ARRAY_SIZE(dvs); i++) {
-		ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap);
-		if (ret)
-			break;
-	}
-	return ret;
-}
-
-static int buck2_set_hw_dvs_levels(struct device_node *np,
-			    const struct regulator_desc *desc,
-			    struct regulator_config *cfg)
-{
-	int ret, i;
-	const struct of_dvs_setting dvs[] = {
-		{
-			.prop = "rohm,dvs-run-voltage",
-			.reg = BD718XX_REG_BUCK2_VOLT_RUN,
-		},
-		{
-			.prop = "rohm,dvs-idle-voltage",
-			.reg = BD718XX_REG_BUCK2_VOLT_IDLE,
-		},
-	};
-
-
-
-	for (i = 0; i < ARRAY_SIZE(dvs); i++) {
-		ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap);
-		if (ret)
-			break;
-	}
-	return ret;
-}
-
-static int buck1_set_hw_dvs_levels(struct device_node *np,
-			    const struct regulator_desc *desc,
-			    struct regulator_config *cfg)
-{
-	int ret, i;
-	const struct of_dvs_setting dvs[] = {
-		{
-			.prop = "rohm,dvs-run-voltage",
-			.reg = BD718XX_REG_BUCK1_VOLT_RUN,
-		},
-		{
-			.prop = "rohm,dvs-idle-voltage",
-			.reg = BD718XX_REG_BUCK1_VOLT_IDLE,
-		},
-		{
-			.prop = "rohm,dvs-suspend-voltage",
-			.reg = BD718XX_REG_BUCK1_VOLT_SUSP,
-		},
-	};
-
-	for (i = 0; i < ARRAY_SIZE(dvs); i++) {
-		ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap);
-		if (ret)
-			break;
-	}
-	return ret;
+	return rohm_regulator_set_dvs_levels(&data->dvs, np, desc, cfg->regmap);
 }
 
 static const struct bd718xx_regulator_data bd71847_regulators[] = {
@@ -496,7 +379,17 @@ static const struct bd718xx_regulator_data bd71847_regulators[] = {
 			.enable_reg = BD718XX_REG_BUCK1_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck1_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND,
+			.run_reg = BD718XX_REG_BUCK1_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
+			.idle_reg = BD718XX_REG_BUCK1_VOLT_IDLE,
+			.idle_mask = DVS_BUCK_RUN_MASK,
+			.suspend_reg = BD718XX_REG_BUCK1_VOLT_SUSP,
+			.suspend_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD718XX_REG_BUCK1_CTRL,
@@ -520,7 +413,14 @@ static const struct bd718xx_regulator_data bd71847_regulators[] = {
 			.enable_reg = BD718XX_REG_BUCK2_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck2_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE,
+			.run_reg = BD718XX_REG_BUCK2_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
+			.idle_reg = BD718XX_REG_BUCK2_VOLT_IDLE,
+			.idle_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD718XX_REG_BUCK2_CTRL,
@@ -792,7 +692,17 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 			.enable_reg = BD718XX_REG_BUCK1_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck1_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND,
+			.run_reg = BD718XX_REG_BUCK1_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
+			.idle_reg = BD718XX_REG_BUCK1_VOLT_IDLE,
+			.idle_mask = DVS_BUCK_RUN_MASK,
+			.suspend_reg = BD718XX_REG_BUCK1_VOLT_SUSP,
+			.suspend_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD718XX_REG_BUCK1_CTRL,
@@ -816,7 +726,14 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 			.enable_reg = BD718XX_REG_BUCK2_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck2_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE,
+			.run_reg = BD718XX_REG_BUCK2_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
+			.idle_reg = BD718XX_REG_BUCK2_VOLT_IDLE,
+			.idle_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD718XX_REG_BUCK2_CTRL,
@@ -840,7 +757,12 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 			.enable_reg = BD71837_REG_BUCK3_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck3_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN,
+			.run_reg = BD71837_REG_BUCK3_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD71837_REG_BUCK3_CTRL,
@@ -864,7 +786,12 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 			.enable_reg = BD71837_REG_BUCK4_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck4_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN,
+			.run_reg = BD71837_REG_BUCK4_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD71837_REG_BUCK4_CTRL,
diff --git a/drivers/regulator/rohm-regulator.c b/drivers/regulator/rohm-regulator.c
new file mode 100644
index 000000000000..ca368ada53c6
--- /dev/null
+++ b/drivers/regulator/rohm-regulator.c
@@ -0,0 +1,95 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2018 ROHM Semiconductors
+
+#include <linux/errno.h>
+#include <linux/mfd/rohm-generic.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+
+static int set_dvs_level(const struct regulator_desc *desc,
+			 struct device_node *np, struct regmap *regmap,
+			 char *prop, unsigned int reg, unsigned int mask,
+			 unsigned int omask, unsigned int oreg)
+{
+	int ret, i;
+	uint32_t uv;
+
+	ret = of_property_read_u32(np, prop, &uv);
+	if (ret) {
+		if (ret != -EINVAL)
+			return ret;
+		return 0;
+	}
+
+	if (uv == 0) {
+		if (omask)
+			return regmap_update_bits(regmap, oreg, omask, 0);
+	}
+	for (i = 0; i < desc->n_voltages; i++) {
+		ret = regulator_desc_list_voltage_linear_range(desc, i);
+		if (ret < 0)
+			continue;
+		if (ret == uv) {
+			i <<= ffs(desc->vsel_mask) - 1;
+			ret = regmap_update_bits(regmap, reg, mask, i);
+			if (omask && !ret)
+				ret = regmap_update_bits(regmap, oreg, omask,
+							 omask);
+			break;
+		}
+	}
+	return ret;
+}
+
+int rohm_regulator_set_dvs_levels(const struct rohm_dvs_config *dvs,
+			  struct device_node *np,
+			  const struct regulator_desc *desc,
+			  struct regmap *regmap)
+{
+	int i, ret = 0;
+	char *prop;
+	unsigned int reg, mask, omask, oreg = desc->enable_reg;
+
+	for (i = 0; i < ROHM_DVS_LEVEL_MAX && !ret; i++) {
+		if (dvs->level_map & (1 << i)) {
+			switch (i + 1) {
+			case ROHM_DVS_LEVEL_RUN:
+				prop = "rohm,dvs-run-voltage";
+				reg = dvs->run_reg;
+				mask = dvs->run_mask;
+				omask = dvs->run_on_mask;
+				break;
+			case ROHM_DVS_LEVEL_IDLE:
+				prop = "rohm,dvs-idle-voltage";
+				reg = dvs->idle_reg;
+				mask = dvs->idle_mask;
+				omask = dvs->idle_on_mask;
+				break;
+			case ROHM_DVS_LEVEL_SUSPEND:
+				prop = "rohm,dvs-suspend-voltage";
+				reg = dvs->suspend_reg;
+				mask = dvs->suspend_mask;
+				omask = dvs->suspend_on_mask;
+				break;
+			case ROHM_DVS_LEVEL_LPSR:
+				prop = "rohm,dvs-lpsr-voltage";
+				reg = dvs->lpsr_reg;
+				mask = dvs->lpsr_mask;
+				omask = dvs->lpsr_on_mask;
+				break;
+			default:
+				return -EINVAL;
+			}
+			ret = set_dvs_level(desc, np, regmap, prop, reg, mask,
+					    omask, oreg);
+		}
+	}
+	return ret;
+}
+EXPORT_SYMBOL(rohm_regulator_set_dvs_levels);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("Generic helpers for ROHM PMIC regulator drivers");
diff --git a/include/linux/mfd/rohm-generic.h b/include/linux/mfd/rohm-generic.h
index ff3dd7578fd3..8037421cc6a1 100644
--- a/include/linux/mfd/rohm-generic.h
+++ b/include/linux/mfd/rohm-generic.h
@@ -4,6 +4,9 @@
 #ifndef __LINUX_MFD_ROHM_H__
 #define __LINUX_MFD_ROHM_H__
 
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+
 enum rohm_chip_type {
 	ROHM_CHIP_TYPE_BD71837 = 0,
 	ROHM_CHIP_TYPE_BD71847,
@@ -17,4 +20,45 @@ struct rohm_regmap_dev {
 	struct regmap *regmap;
 };
 
+enum {
+	ROHM_DVS_LEVEL_UNKNOWN,
+	ROHM_DVS_LEVEL_RUN,
+	ROHM_DVS_LEVEL_IDLE,
+	ROHM_DVS_LEVEL_SUSPEND,
+	ROHM_DVS_LEVEL_LPSR,
+#define ROHM_DVS_LEVEL_MAX ROHM_DVS_LEVEL_LPSR
+};
+
+struct rohm_dvs_config {
+	uint64_t level_map;
+	unsigned int run_reg;
+	unsigned int run_mask;
+	unsigned int run_on_mask;
+	unsigned int idle_reg;
+	unsigned int idle_mask;
+	unsigned int idle_on_mask;
+	unsigned int suspend_reg;
+	unsigned int suspend_mask;
+	unsigned int suspend_on_mask;
+	unsigned int lpsr_reg;
+	unsigned int lpsr_mask;
+	unsigned int lpsr_on_mask;
+};
+
+#if IS_ENABLED(CONFIG_REGULATOR_ROHM)
+int rohm_regulator_set_dvs_levels(const struct rohm_dvs_config *dvs,
+				  struct device_node *np,
+				  const struct regulator_desc *desc,
+				  struct regmap *regmap);
+
+#else
+static inline int rohm_regulator_set_dvs_levels(const struct rohm_dvs_config *dvs,
+						struct device_node *np,
+						const struct regulator_desc *desc,
+						struct regmap *regmap)
+{
+	return 0;
+}
+#endif //IS_ENABLED(CONFIG_REGULATOR_ROHM)
+
 #endif
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply related	[flat|nested] 19+ messages in thread

* [PATCH v4 09/16] regulator: bd71828: Basic support for ROHM bd71828 PMIC regulators
  2019-11-16 18:55 [PATCH v4 00/16] Support ROHM BD71828 PMIC Matti Vaittinen
                   ` (7 preceding siblings ...)
  2019-11-16 18:59 ` [PATCH v4 08/16] regulator: bd718x7: Split driver to common and bd718x7 specific parts Matti Vaittinen
@ 2019-11-16 18:59 ` Matti Vaittinen
  2019-11-16 18:59 ` [PATCH v4 10/16] gpio: devres: Add devm_gpiod_get_parent_array Matti Vaittinen
                   ` (6 subsequent siblings)
  15 siblings, 0 replies; 19+ messages in thread
From: Matti Vaittinen @ 2019-11-16 18:59 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Lee Jones, Jacek Anaszewski, Pavel Machek, Dan Murphy,
	Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Mauro Carvalho Chehab, Jeff Kirsher, Wolfram Sang,
	Marek Szyprowski, Heiner Kallweit, Nicholas Mc Guire,
	Phil Edworthy, linux-leds, devicetree, linux-kernel, linux-doc,
	linux-clk, linux-gpio, linux-rtc

ROHM BD71828 is a power management IC containing 7 bucks and 7 LDOs. Bucks
1,2,6 and 7 can be assigned to a regulator group controlled by run-levels.
Eg. Voltages and enable/disable statuses for specific run-levels (run0 to
run3) can be set via register interface and run level changes can then be
done either via I2C or GPIO.

This initial commit does not support assigning bucks to be controlled via
run-levels but only allows them to be individually controlled.

LDO5 voltage can also be controlled by GPIO2 pin and register interfaces
but this driver only supports the control via register.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
 drivers/regulator/Kconfig             |  12 +
 drivers/regulator/Makefile            |   1 +
 drivers/regulator/bd71828-regulator.c | 833 ++++++++++++++++++++++++++
 3 files changed, 846 insertions(+)
 create mode 100644 drivers/regulator/bd71828-regulator.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 5182a3d5660c..838bbfcf11ea 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -194,6 +194,18 @@ config REGULATOR_BD70528
 	  This driver can also be built as a module. If so, the module
 	  will be called bd70528-regulator.
 
+config REGULATOR_BD71828
+	tristate "ROHM BD71828 Power Regulator"
+	depends on MFD_ROHM_BD71828
+	select REGULATOR_ROHM
+	help
+	  This driver supports voltage regulators on ROHM BD71828 PMIC.
+	  This will enable support for the software controllable buck
+	  and LDO regulators.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called bd71828-regulator.
+
 config REGULATOR_BD718XX
 	tristate "ROHM BD71837 Power Regulator"
 	depends on MFD_ROHM_BD718XX
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 6bcab72c1fc7..cf0e08c5f3cd 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -28,6 +28,7 @@ obj-$(CONFIG_REGULATOR_AS3722) += as3722-regulator.o
 obj-$(CONFIG_REGULATOR_AXP20X) += axp20x-regulator.o
 obj-$(CONFIG_REGULATOR_BCM590XX) += bcm590xx-regulator.o
 obj-$(CONFIG_REGULATOR_BD70528) += bd70528-regulator.o
+obj-$(CONFIG_REGULATOR_BD71828) += bd71828-regulator.o
 obj-$(CONFIG_REGULATOR_BD718XX) += bd718x7-regulator.o
 obj-$(CONFIG_REGULATOR_BD9571MWV) += bd9571mwv-regulator.o
 obj-$(CONFIG_REGULATOR_DA903X)	+= da903x.o
diff --git a/drivers/regulator/bd71828-regulator.c b/drivers/regulator/bd71828-regulator.c
new file mode 100644
index 000000000000..b113cec41969
--- /dev/null
+++ b/drivers/regulator/bd71828-regulator.c
@@ -0,0 +1,833 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2019 ROHM Semiconductors
+// bd71828-regulator.c ROHM BD71828GW-DS1 regulator driver
+//
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/rohm-bd71828.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
+
+struct reg_init {
+	unsigned int reg;
+	unsigned int mask;
+	unsigned int val;
+};
+struct bd71828_regulator_data {
+	struct regulator_desc desc;
+	const struct rohm_dvs_config dvs;
+	const struct reg_init *reg_inits;
+	int reg_init_amnt;
+};
+
+static const struct reg_init buck1_inits[] = {
+	/*
+	 * DVS Buck voltages can be changed by register values or via GPIO.
+	 * Use register accesses by default.
+	 */
+	{
+		.reg = BD71828_REG_PS_CTRL_1,
+		.mask = BD71828_MASK_DVS_BUCK1_CTRL,
+		.val = BD71828_DVS_BUCK1_CTRL_I2C,
+	},
+};
+
+static const struct reg_init buck2_inits[] = {
+	{
+		.reg = BD71828_REG_PS_CTRL_1,
+		.mask = BD71828_MASK_DVS_BUCK2_CTRL,
+		.val = BD71828_DVS_BUCK2_CTRL_I2C,
+	},
+};
+
+static const struct reg_init buck6_inits[] = {
+	{
+		.reg = BD71828_REG_PS_CTRL_1,
+		.mask = BD71828_MASK_DVS_BUCK6_CTRL,
+		.val = BD71828_DVS_BUCK6_CTRL_I2C,
+	},
+};
+
+static const struct reg_init buck7_inits[] = {
+	{
+		.reg = BD71828_REG_PS_CTRL_1,
+		.mask = BD71828_MASK_DVS_BUCK7_CTRL,
+		.val = BD71828_DVS_BUCK7_CTRL_I2C,
+	},
+};
+
+static const struct regulator_linear_range bd71828_buck1267_volts[] = {
+	REGULATOR_LINEAR_RANGE(500000, 0x00, 0xef, 6250),
+	REGULATOR_LINEAR_RANGE(2000000, 0xf0, 0xff, 0),
+};
+
+static const struct regulator_linear_range bd71828_buck3_volts[] = {
+	REGULATOR_LINEAR_RANGE(1200000, 0x00, 0x0f, 50000),
+	REGULATOR_LINEAR_RANGE(2000000, 0x10, 0x1f, 0),
+};
+
+static const struct regulator_linear_range bd71828_buck4_volts[] = {
+	REGULATOR_LINEAR_RANGE(1000000, 0x00, 0x1f, 25000),
+	REGULATOR_LINEAR_RANGE(1800000, 0x20, 0x3f, 0),
+};
+
+static const struct regulator_linear_range bd71828_buck5_volts[] = {
+	REGULATOR_LINEAR_RANGE(2500000, 0x00, 0x0f, 50000),
+	REGULATOR_LINEAR_RANGE(3300000, 0x10, 0x1f, 0),
+};
+
+static const struct regulator_linear_range bd71828_ldo_volts[] = {
+	REGULATOR_LINEAR_RANGE(800000, 0x00, 0x31, 50000),
+	REGULATOR_LINEAR_RANGE(3300000, 0x32, 0x3f, 0),
+};
+
+static int ramp_delay_supported(struct regulator_dev *rdev)
+{
+	switch (rdev->desc->id) {
+	case BD71828_BUCK1:
+	case BD71828_BUCK2:
+	case BD71828_BUCK6:
+	case BD71828_BUCK7:
+		return 1;
+	default:
+		break;
+	}
+	return 0;
+}
+
+static int bd71828_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay)
+{
+	unsigned int val;
+
+	if (!ramp_delay_supported(rdev)) {
+		dev_err(&rdev->dev, "%s: can't set ramp-delay\n",
+			rdev->desc->name);
+		return -EINVAL;
+	}
+
+	switch (ramp_delay) {
+	case 1 ... 2500:
+		val = 0;
+		break;
+	case 2501 ... 5000:
+		val = 1;
+		break;
+	case 5001 ... 10000:
+		val = 2;
+		break;
+	case 10001 ... 20000:
+		val = 3;
+		break;
+	default:
+		val = 3;
+		dev_err(&rdev->dev,
+			"ramp_delay: %d not supported, setting 20mV/uS",
+			 ramp_delay);
+	}
+
+	/*
+	 * On BD71828 the ramp delay level control reg is at offset +2 to
+	 * enable reg
+	 */
+	return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg + 2,
+				  BD71828_MASK_RAMP_DELAY,
+				  val << (ffs(BD71828_MASK_RAMP_DELAY) - 1));
+
+}
+
+static int buck_set_hw_dvs_levels(struct device_node *np,
+				  const struct regulator_desc *desc,
+				  struct regulator_config *cfg)
+{
+	struct bd71828_regulator_data *data;
+
+	data = container_of(desc, struct bd71828_regulator_data, desc);
+
+	return rohm_regulator_set_dvs_levels(&data->dvs, np, desc, cfg->regmap);
+}
+
+static int ldo6_parse_dt(struct device_node *np,
+			 const struct regulator_desc *desc,
+			 struct regulator_config *cfg)
+{
+	int ret, i;
+	uint32_t uv = 0;
+	unsigned int en;
+	struct regmap *regmap = cfg->regmap;
+	static const char * const props[] = { "rohm,dvs-run-voltage",
+					      "rohm,dvs-idle-voltage",
+					      "rohm,dvs-suspend-voltage",
+					      "rohm,dvs-lpsr-voltage" };
+	unsigned int mask[] = { BD71828_MASK_RUN_EN, BD71828_MASK_IDLE_EN,
+			       BD71828_MASK_SUSP_EN, BD71828_MASK_LPSR_EN };
+
+	for (i = 0; i < ARRAY_SIZE(props); i++) {
+		ret = of_property_read_u32(np, props[i], &uv);
+		if (ret) {
+			if (ret != -EINVAL)
+				return ret;
+			continue;
+		}
+		if (uv)
+			en = 0xffffffff;
+		else
+			en = 0;
+
+		ret = regmap_update_bits(regmap, desc->enable_reg, mask[i], en);
+		if (ret)
+			return ret;
+	}
+	return 0;
+}
+
+static const struct regulator_ops bd71828_buck_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.list_voltage = regulator_list_voltage_linear_range,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+};
+
+static const struct regulator_ops bd71828_dvs_buck_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.list_voltage = regulator_list_voltage_linear_range,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.set_voltage_time_sel = regulator_set_voltage_time_sel,
+	.set_ramp_delay = bd71828_set_ramp_delay,
+};
+
+static const struct regulator_ops bd71828_ldo_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.list_voltage = regulator_list_voltage_linear_range,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+};
+
+static int bd71828_ldo6_get_voltage(struct regulator_dev *rdev)
+{
+	return BD71828_LDO_6_VOLTAGE;
+}
+
+static const struct regulator_ops bd71828_ldo6_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.get_voltage = bd71828_ldo6_get_voltage,
+	.is_enabled = regulator_is_enabled_regmap,
+};
+
+static const struct bd71828_regulator_data bd71828_rdata[] = {
+	{
+		.desc = {
+			.name = "buck1",
+			.of_match = of_match_ptr("BUCK1"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_BUCK1,
+			.ops = &bd71828_dvs_buck_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_buck1267_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_buck1267_volts),
+			.n_voltages = BD71828_BUCK1267_VOLTS,
+			.enable_reg = BD71828_REG_BUCK1_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_BUCK1_VOLT,
+			.vsel_mask = BD71828_MASK_BUCK1267_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_BUCK1_VOLT,
+			.run_mask = BD71828_MASK_BUCK1267_VOLT,
+			.idle_reg = BD71828_REG_BUCK1_IDLE_VOLT,
+			.idle_mask = BD71828_MASK_BUCK1267_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_reg = BD71828_REG_BUCK1_SUSP_VOLT,
+			.suspend_mask = BD71828_MASK_BUCK1267_VOLT,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+			/*
+			 * LPSR voltage is same as SUSPEND voltage. Allow
+			 * setting it so that regulator can be set enabled at
+			 * LPSR state
+			 */
+			.lpsr_reg = BD71828_REG_BUCK1_SUSP_VOLT,
+			.lpsr_mask = BD71828_MASK_BUCK1267_VOLT,
+		},
+		.reg_inits = buck1_inits,
+		.reg_init_amnt = ARRAY_SIZE(buck1_inits),
+	},
+	{
+		.desc = {
+			.name = "buck2",
+			.of_match = of_match_ptr("BUCK2"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_BUCK2,
+			.ops = &bd71828_dvs_buck_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_buck1267_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_buck1267_volts),
+			.n_voltages = BD71828_BUCK1267_VOLTS,
+			.enable_reg = BD71828_REG_BUCK2_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_BUCK2_VOLT,
+			.vsel_mask = BD71828_MASK_BUCK1267_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_BUCK2_VOLT,
+			.run_mask = BD71828_MASK_BUCK1267_VOLT,
+			.idle_reg = BD71828_REG_BUCK2_IDLE_VOLT,
+			.idle_mask = BD71828_MASK_BUCK1267_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_reg = BD71828_REG_BUCK2_SUSP_VOLT,
+			.suspend_mask = BD71828_MASK_BUCK1267_VOLT,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+			.lpsr_reg = BD71828_REG_BUCK2_SUSP_VOLT,
+			.lpsr_mask = BD71828_MASK_BUCK1267_VOLT,
+		},
+		.reg_inits = buck2_inits,
+		.reg_init_amnt = ARRAY_SIZE(buck2_inits),
+	},
+	{
+		.desc = {
+			.name = "buck3",
+			.of_match = of_match_ptr("BUCK3"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_BUCK3,
+			.ops = &bd71828_buck_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_buck3_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_buck3_volts),
+			.n_voltages = BD71828_BUCK3_VOLTS,
+			.enable_reg = BD71828_REG_BUCK3_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_BUCK3_VOLT,
+			.vsel_mask = BD71828_MASK_BUCK3_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			/*
+			 * BUCK3 only supports single voltage for all states.
+			 * voltage can be individually enabled for each state
+			 * though => allow setting all states to support
+			 * enabling power rail on different states.
+			 */
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_BUCK3_VOLT,
+			.idle_reg = BD71828_REG_BUCK3_VOLT,
+			.suspend_reg = BD71828_REG_BUCK3_VOLT,
+			.lpsr_reg = BD71828_REG_BUCK3_VOLT,
+			.run_mask = BD71828_MASK_BUCK3_VOLT,
+			.idle_mask = BD71828_MASK_BUCK3_VOLT,
+			.suspend_mask = BD71828_MASK_BUCK3_VOLT,
+			.lpsr_mask = BD71828_MASK_BUCK3_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+		},
+	},
+	{
+		.desc = {
+			.name = "buck4",
+			.of_match = of_match_ptr("BUCK4"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_BUCK4,
+			.ops = &bd71828_buck_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_buck4_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_buck4_volts),
+			.n_voltages = BD71828_BUCK4_VOLTS,
+			.enable_reg = BD71828_REG_BUCK4_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_BUCK4_VOLT,
+			.vsel_mask = BD71828_MASK_BUCK4_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			/*
+			 * BUCK4 only supports single voltage for all states.
+			 * voltage can be individually enabled for each state
+			 * though => allow setting all states to support
+			 * enabling power rail on different states.
+			 */
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_BUCK4_VOLT,
+			.idle_reg = BD71828_REG_BUCK4_VOLT,
+			.suspend_reg = BD71828_REG_BUCK4_VOLT,
+			.lpsr_reg = BD71828_REG_BUCK4_VOLT,
+			.run_mask = BD71828_MASK_BUCK4_VOLT,
+			.idle_mask = BD71828_MASK_BUCK4_VOLT,
+			.suspend_mask = BD71828_MASK_BUCK4_VOLT,
+			.lpsr_mask = BD71828_MASK_BUCK4_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+		},
+	},
+	{
+		.desc = {
+			.name = "buck5",
+			.of_match = of_match_ptr("BUCK5"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_BUCK5,
+			.ops = &bd71828_buck_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_buck5_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_buck5_volts),
+			.n_voltages = BD71828_BUCK5_VOLTS,
+			.enable_reg = BD71828_REG_BUCK5_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_BUCK5_VOLT,
+			.vsel_mask = BD71828_MASK_BUCK5_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			/*
+			 * BUCK5 only supports single voltage for all states.
+			 * voltage can be individually enabled for each state
+			 * though => allow setting all states to support
+			 * enabling power rail on different states.
+			 */
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_BUCK5_VOLT,
+			.idle_reg = BD71828_REG_BUCK5_VOLT,
+			.suspend_reg = BD71828_REG_BUCK5_VOLT,
+			.lpsr_reg = BD71828_REG_BUCK5_VOLT,
+			.run_mask = BD71828_MASK_BUCK5_VOLT,
+			.idle_mask = BD71828_MASK_BUCK5_VOLT,
+			.suspend_mask = BD71828_MASK_BUCK5_VOLT,
+			.lpsr_mask = BD71828_MASK_BUCK5_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+		},
+	},
+	{
+		.desc = {
+			.name = "buck6",
+			.of_match = of_match_ptr("BUCK6"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_BUCK6,
+			.ops = &bd71828_dvs_buck_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_buck1267_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_buck1267_volts),
+			.n_voltages = BD71828_BUCK1267_VOLTS,
+			.enable_reg = BD71828_REG_BUCK6_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_BUCK6_VOLT,
+			.vsel_mask = BD71828_MASK_BUCK1267_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_BUCK6_VOLT,
+			.run_mask = BD71828_MASK_BUCK1267_VOLT,
+			.idle_reg = BD71828_REG_BUCK6_IDLE_VOLT,
+			.idle_mask = BD71828_MASK_BUCK1267_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_reg = BD71828_REG_BUCK6_SUSP_VOLT,
+			.suspend_mask = BD71828_MASK_BUCK1267_VOLT,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+			.lpsr_reg = BD71828_REG_BUCK6_SUSP_VOLT,
+			.lpsr_mask = BD71828_MASK_BUCK1267_VOLT,
+		},
+		.reg_inits = buck6_inits,
+		.reg_init_amnt = ARRAY_SIZE(buck6_inits),
+	},
+	{
+		.desc = {
+			.name = "buck7",
+			.of_match = of_match_ptr("BUCK7"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_BUCK7,
+			.ops = &bd71828_dvs_buck_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_buck1267_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_buck1267_volts),
+			.n_voltages = BD71828_BUCK1267_VOLTS,
+			.enable_reg = BD71828_REG_BUCK7_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_BUCK7_VOLT,
+			.vsel_mask = BD71828_MASK_BUCK1267_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_BUCK7_VOLT,
+			.run_mask = BD71828_MASK_BUCK1267_VOLT,
+			.idle_reg = BD71828_REG_BUCK7_IDLE_VOLT,
+			.idle_mask = BD71828_MASK_BUCK1267_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_reg = BD71828_REG_BUCK7_SUSP_VOLT,
+			.suspend_mask = BD71828_MASK_BUCK1267_VOLT,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+			.lpsr_reg = BD71828_REG_BUCK7_SUSP_VOLT,
+			.lpsr_mask = BD71828_MASK_BUCK1267_VOLT,
+		},
+		.reg_inits = buck7_inits,
+		.reg_init_amnt = ARRAY_SIZE(buck7_inits),
+	},
+	{
+		.desc = {
+			.name = "ldo1",
+			.of_match = of_match_ptr("LDO1"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_LDO1,
+			.ops = &bd71828_ldo_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_ldo_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_ldo_volts),
+			.n_voltages = BD71828_LDO_VOLTS,
+			.enable_reg = BD71828_REG_LDO1_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_LDO1_VOLT,
+			.vsel_mask = BD71828_MASK_LDO_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			/*
+			 * LDO1 only supports single voltage for all states.
+			 * voltage can be individually enabled for each state
+			 * though => allow setting all states to support
+			 * enabling power rail on different states.
+			 */
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_LDO1_VOLT,
+			.idle_reg = BD71828_REG_LDO1_VOLT,
+			.suspend_reg = BD71828_REG_LDO1_VOLT,
+			.lpsr_reg = BD71828_REG_LDO1_VOLT,
+			.run_mask = BD71828_MASK_LDO_VOLT,
+			.idle_mask = BD71828_MASK_LDO_VOLT,
+			.suspend_mask = BD71828_MASK_LDO_VOLT,
+			.lpsr_mask = BD71828_MASK_LDO_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+		},
+	}, {
+		.desc = {
+			.name = "ldo2",
+			.of_match = of_match_ptr("LDO2"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_LDO2,
+			.ops = &bd71828_ldo_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_ldo_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_ldo_volts),
+			.n_voltages = BD71828_LDO_VOLTS,
+			.enable_reg = BD71828_REG_LDO2_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_LDO2_VOLT,
+			.vsel_mask = BD71828_MASK_LDO_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			/*
+			 * LDO2 only supports single voltage for all states.
+			 * voltage can be individually enabled for each state
+			 * though => allow setting all states to support
+			 * enabling power rail on different states.
+			 */
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_LDO2_VOLT,
+			.idle_reg = BD71828_REG_LDO2_VOLT,
+			.suspend_reg = BD71828_REG_LDO2_VOLT,
+			.lpsr_reg = BD71828_REG_LDO2_VOLT,
+			.run_mask = BD71828_MASK_LDO_VOLT,
+			.idle_mask = BD71828_MASK_LDO_VOLT,
+			.suspend_mask = BD71828_MASK_LDO_VOLT,
+			.lpsr_mask = BD71828_MASK_LDO_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+		},
+	}, {
+		.desc = {
+			.name = "ldo3",
+			.of_match = of_match_ptr("LDO3"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_LDO3,
+			.ops = &bd71828_ldo_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_ldo_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_ldo_volts),
+			.n_voltages = BD71828_LDO_VOLTS,
+			.enable_reg = BD71828_REG_LDO3_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_LDO3_VOLT,
+			.vsel_mask = BD71828_MASK_LDO_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			/*
+			 * LDO3 only supports single voltage for all states.
+			 * voltage can be individually enabled for each state
+			 * though => allow setting all states to support
+			 * enabling power rail on different states.
+			 */
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_LDO3_VOLT,
+			.idle_reg = BD71828_REG_LDO3_VOLT,
+			.suspend_reg = BD71828_REG_LDO3_VOLT,
+			.lpsr_reg = BD71828_REG_LDO3_VOLT,
+			.run_mask = BD71828_MASK_LDO_VOLT,
+			.idle_mask = BD71828_MASK_LDO_VOLT,
+			.suspend_mask = BD71828_MASK_LDO_VOLT,
+			.lpsr_mask = BD71828_MASK_LDO_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+		},
+
+	}, {
+		.desc = {
+			.name = "ldo4",
+			.of_match = of_match_ptr("LDO4"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_LDO4,
+			.ops = &bd71828_ldo_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_ldo_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_ldo_volts),
+			.n_voltages = BD71828_LDO_VOLTS,
+			.enable_reg = BD71828_REG_LDO4_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_LDO4_VOLT,
+			.vsel_mask = BD71828_MASK_LDO_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			/*
+			 * LDO1 only supports single voltage for all states.
+			 * voltage can be individually enabled for each state
+			 * though => allow setting all states to support
+			 * enabling power rail on different states.
+			 */
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_LDO4_VOLT,
+			.idle_reg = BD71828_REG_LDO4_VOLT,
+			.suspend_reg = BD71828_REG_LDO4_VOLT,
+			.lpsr_reg = BD71828_REG_LDO4_VOLT,
+			.run_mask = BD71828_MASK_LDO_VOLT,
+			.idle_mask = BD71828_MASK_LDO_VOLT,
+			.suspend_mask = BD71828_MASK_LDO_VOLT,
+			.lpsr_mask = BD71828_MASK_LDO_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+		},
+	}, {
+		.desc = {
+			.name = "ldo5",
+			.of_match = of_match_ptr("LDO5"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_LDO5,
+			.ops = &bd71828_ldo_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_ldo_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_ldo_volts),
+			.n_voltages = BD71828_LDO_VOLTS,
+			.enable_reg = BD71828_REG_LDO5_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_LDO5_VOLT,
+			.vsel_mask = BD71828_MASK_LDO_VOLT,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+			.owner = THIS_MODULE,
+		},
+		/*
+		 * LDO5 is special. It can choose vsel settings to be configured
+		 * from 2 different registers (by GPIO).
+		 *
+		 * This driver supports only configuration where
+		 * BD71828_REG_LDO5_VOLT_L is used.
+		 */
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_LDO5_VOLT,
+			.idle_reg = BD71828_REG_LDO5_VOLT,
+			.suspend_reg = BD71828_REG_LDO5_VOLT,
+			.lpsr_reg = BD71828_REG_LDO5_VOLT,
+			.run_mask = BD71828_MASK_LDO_VOLT,
+			.idle_mask = BD71828_MASK_LDO_VOLT,
+			.suspend_mask = BD71828_MASK_LDO_VOLT,
+			.lpsr_mask = BD71828_MASK_LDO_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+		},
+
+	}, {
+		.desc = {
+			.name = "ldo6",
+			.of_match = of_match_ptr("LDO6"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_LDO6,
+			.ops = &bd71828_ldo6_ops,
+			.type = REGULATOR_VOLTAGE,
+			.n_voltages = 1,
+			.enable_reg = BD71828_REG_LDO6_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.owner = THIS_MODULE,
+			/*
+			 * LDO6 only supports enable/disable for all states.
+			 * Voltage for LDO6 is fixed.
+			 */
+			.of_parse_cb = ldo6_parse_dt,
+		},
+	}, {
+		.desc = {
+			/* SNVS LDO in data-sheet */
+			.name = "ldo7",
+			.of_match = of_match_ptr("LDO7"),
+			.regulators_node = of_match_ptr("regulators"),
+			.id = BD71828_LDO_SNVS,
+			.ops = &bd71828_ldo_ops,
+			.type = REGULATOR_VOLTAGE,
+			.linear_ranges = bd71828_ldo_volts,
+			.n_linear_ranges = ARRAY_SIZE(bd71828_ldo_volts),
+			.n_voltages = BD71828_LDO_VOLTS,
+			.enable_reg = BD71828_REG_LDO7_EN,
+			.enable_mask = BD71828_MASK_RUN_EN,
+			.vsel_reg = BD71828_REG_LDO7_VOLT,
+			.vsel_mask = BD71828_MASK_LDO_VOLT,
+			.owner = THIS_MODULE,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			/*
+			 * LDO7 only supports single voltage for all states.
+			 * voltage can be individually enabled for each state
+			 * though => allow setting all states to support
+			 * enabling power rail on different states.
+			 */
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND |
+				     ROHM_DVS_LEVEL_LPSR,
+			.run_reg = BD71828_REG_LDO7_VOLT,
+			.idle_reg = BD71828_REG_LDO7_VOLT,
+			.suspend_reg = BD71828_REG_LDO7_VOLT,
+			.lpsr_reg = BD71828_REG_LDO7_VOLT,
+			.run_mask = BD71828_MASK_LDO_VOLT,
+			.idle_mask = BD71828_MASK_LDO_VOLT,
+			.suspend_mask = BD71828_MASK_LDO_VOLT,
+			.lpsr_mask = BD71828_MASK_LDO_VOLT,
+			.idle_on_mask = BD71828_MASK_IDLE_EN,
+			.suspend_on_mask = BD71828_MASK_SUSP_EN,
+			.lpsr_on_mask = BD71828_MASK_LPSR_EN,
+		},
+
+	},
+};
+
+static int bd71828_probe(struct platform_device *pdev)
+{
+	struct rohm_regmap_dev *bd71828;
+	int i, j, ret;
+	struct regulator_config config = {
+		.dev = pdev->dev.parent,
+	};
+
+	bd71828 = dev_get_drvdata(pdev->dev.parent);
+	if (!bd71828) {
+		dev_err(&pdev->dev, "No MFD driver data\n");
+		return -EINVAL;
+	}
+
+	config.regmap = bd71828->regmap;
+
+	for (i = 0; i < ARRAY_SIZE(bd71828_rdata); i++) {
+		struct regulator_dev *rdev;
+		const struct bd71828_regulator_data *rd;
+
+		rd = &bd71828_rdata[i];
+		rdev = devm_regulator_register(&pdev->dev,
+					       &rd->desc, &config);
+		if (IS_ERR(rdev)) {
+			dev_err(&pdev->dev,
+				"failed to register %s regulator\n",
+				rd->desc.name);
+			return PTR_ERR(rdev);
+		}
+		for (j = 0; j < rd->reg_init_amnt; j++) {
+			ret = regmap_update_bits(bd71828->regmap,
+						 rd->reg_inits[j].reg,
+						 rd->reg_inits[j].mask,
+						 rd->reg_inits[j].val);
+			if (ret) {
+				dev_err(&pdev->dev,
+					"regulator %s init failed\n",
+					rd->desc.name);
+				return ret;
+			}
+		}
+	}
+	return 0;
+}
+
+static struct platform_driver bd71828_regulator = {
+	.driver = {
+		.name = "bd71828-pmic"
+	},
+	.probe = bd71828_probe,
+};
+
+module_platform_driver(bd71828_regulator);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("BD71828 voltage regulator driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:bd71828-pmic");
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply related	[flat|nested] 19+ messages in thread

* [PATCH v4 10/16] gpio: devres: Add devm_gpiod_get_parent_array
  2019-11-16 18:55 [PATCH v4 00/16] Support ROHM BD71828 PMIC Matti Vaittinen
                   ` (8 preceding siblings ...)
  2019-11-16 18:59 ` [PATCH v4 09/16] regulator: bd71828: Basic support for ROHM bd71828 PMIC regulators Matti Vaittinen
@ 2019-11-16 18:59 ` Matti Vaittinen
  2019-11-16 19:00 ` [PATCH v4 11/16] docs: driver-model: Add missing managed GPIO array get functions Matti Vaittinen
                   ` (5 subsequent siblings)
  15 siblings, 0 replies; 19+ messages in thread
From: Matti Vaittinen @ 2019-11-16 18:59 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Lee Jones, Jacek Anaszewski, Pavel Machek, Dan Murphy,
	Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Mauro Carvalho Chehab, Jeff Kirsher, Wolfram Sang,
	Marek Szyprowski, Heiner Kallweit, Nicholas Mc Guire,
	Phil Edworthy, linux-leds, devicetree, linux-kernel, linux-doc,
	linux-clk, linux-gpio, linux-rtc

Bunch of MFD sub-devices which are instantiated by MFD do not have
own device-tree nodes but have (for example) the GPIO consumer
information in parent device's DT node. Add resource managed
devm_gpiod_get_array() for such devices so that they can get the
consumer information from parent DT while still binding the GPIO
reservation life-time to this sub-device life time.

If devm_gpiod_get_array is used as such - then unloading and then
re-loading the child device fails as the GPIOs reserved during first
load are not freed when driver for sub-device is unload (if parent
stays there).

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
 .../driver-api/driver-model/devres.rst        |  1 +
 drivers/gpio/gpiolib-devres.c                 | 65 ++++++++++++++-----
 include/linux/gpio/consumer.h                 |  5 ++
 3 files changed, 56 insertions(+), 15 deletions(-)

diff --git a/Documentation/driver-api/driver-model/devres.rst b/Documentation/driver-api/driver-model/devres.rst
index a100bef54952..1b8302ba405b 100644
--- a/Documentation/driver-api/driver-model/devres.rst
+++ b/Documentation/driver-api/driver-model/devres.rst
@@ -270,6 +270,7 @@ GPIO
   devm_gpiod_get_index()
   devm_gpiod_get_index_optional()
   devm_gpiod_get_optional()
+  devm_gpiod_get_parent_array()
   devm_gpiod_put()
   devm_gpiod_unhinge()
   devm_gpiochip_add_data()
diff --git a/drivers/gpio/gpiolib-devres.c b/drivers/gpio/gpiolib-devres.c
index 98e3c20d9730..584fa6edfd20 100644
--- a/drivers/gpio/gpiolib-devres.c
+++ b/drivers/gpio/gpiolib-devres.c
@@ -270,19 +270,11 @@ struct gpio_desc *__must_check devm_gpiod_get_index_optional(struct device *dev,
 }
 EXPORT_SYMBOL_GPL(devm_gpiod_get_index_optional);
 
-/**
- * devm_gpiod_get_array - Resource-managed gpiod_get_array()
- * @dev:	GPIO consumer
- * @con_id:	function within the GPIO consumer
- * @flags:	optional GPIO initialization flags
- *
- * Managed gpiod_get_array(). GPIO descriptors returned from this function are
- * automatically disposed on driver detach. See gpiod_get_array() for detailed
- * information about behavior and return values.
- */
-struct gpio_descs *__must_check devm_gpiod_get_array(struct device *dev,
-						     const char *con_id,
-						     enum gpiod_flags flags)
+static struct gpio_descs *__must_check
+__devm_gpiod_get_array(struct device *gpiodev,
+		       struct device *managed,
+		       const char *con_id,
+		       enum gpiod_flags flags)
 {
 	struct gpio_descs **dr;
 	struct gpio_descs *descs;
@@ -292,19 +284,62 @@ struct gpio_descs *__must_check devm_gpiod_get_array(struct device *dev,
 	if (!dr)
 		return ERR_PTR(-ENOMEM);
 
-	descs = gpiod_get_array(dev, con_id, flags);
+	descs = gpiod_get_array(gpiodev, con_id, flags);
 	if (IS_ERR(descs)) {
 		devres_free(dr);
 		return descs;
 	}
 
 	*dr = descs;
-	devres_add(dev, dr);
+	if (managed)
+		devres_add(managed, dr);
+	else
+		devres_add(gpiodev, dr);
 
 	return descs;
 }
+
+/**
+ * devm_gpiod_get_array - Resource-managed gpiod_get_array()
+ * @dev:	GPIO consumer
+ * @con_id:	function within the GPIO consumer
+ * @flags:	optional GPIO initialization flags
+ *
+ * Managed gpiod_get_array(). GPIO descriptors returned from this function are
+ * automatically disposed on driver detach. See gpiod_get_array() for detailed
+ * information about behavior and return values.
+ */
+struct gpio_descs *__must_check devm_gpiod_get_array(struct device *dev,
+						     const char *con_id,
+						     enum gpiod_flags flags)
+{
+	return __devm_gpiod_get_array(dev, NULL, con_id, flags);
+}
 EXPORT_SYMBOL_GPL(devm_gpiod_get_array);
 
+/**
+ * devm_gpiod_get_parent_array - Resource-managed gpiod_get_array for subdevices
+ * @dev:	Managed device whose parent is the GPIO consumer
+ * @con_id:	function within the GPIO consumer
+ * @flags:	optional GPIO initialization flags
+ *
+ * Managed gpiod_get_array() for subdevices. This function is intended to be
+ * used by MFD sub-devices whose GPIO bindings are in parent (MFD) device but
+ * whose GPIO reservation should last only for the dub-device life time.
+ * Returns EINVAL if no parent device is found. Rest of the behaviour and
+ * return values are as documented for gpiod_get_array()
+ */
+struct gpio_descs *__must_check
+devm_gpiod_get_parent_array(struct device *dev,
+			    const char *con_id,
+			    enum gpiod_flags flags)
+{
+	if (!dev | !dev->parent)
+		return ERR_PTR(-EINVAL);
+	return __devm_gpiod_get_array(dev->parent, dev, con_id, flags);
+}
+EXPORT_SYMBOL_GPL(devm_gpiod_get_parent_array);
+
 /**
  * devm_gpiod_get_array_optional - Resource-managed gpiod_get_array_optional()
  * @dev:	GPIO consumer
diff --git a/include/linux/gpio/consumer.h b/include/linux/gpio/consumer.h
index b70af921c614..01a82b1c6828 100644
--- a/include/linux/gpio/consumer.h
+++ b/include/linux/gpio/consumer.h
@@ -103,6 +103,11 @@ struct gpio_descs *__must_check devm_gpiod_get_array(struct device *dev,
 struct gpio_descs *__must_check
 devm_gpiod_get_array_optional(struct device *dev, const char *con_id,
 			      enum gpiod_flags flags);
+struct gpio_descs *__must_check
+devm_gpiod_get_parent_array(struct device *dev,
+			    const char *con_id,
+			    enum gpiod_flags flags);
+
 void devm_gpiod_put(struct device *dev, struct gpio_desc *desc);
 void devm_gpiod_unhinge(struct device *dev, struct gpio_desc *desc);
 void devm_gpiod_put_array(struct device *dev, struct gpio_descs *descs);
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply related	[flat|nested] 19+ messages in thread

* [PATCH v4 11/16] docs: driver-model: Add missing managed GPIO array get functions
  2019-11-16 18:55 [PATCH v4 00/16] Support ROHM BD71828 PMIC Matti Vaittinen
                   ` (9 preceding siblings ...)
  2019-11-16 18:59 ` [PATCH v4 10/16] gpio: devres: Add devm_gpiod_get_parent_array Matti Vaittinen
@ 2019-11-16 19:00 ` Matti Vaittinen
  2019-11-16 19:00 ` [PATCH v4 12/16] regulator: bd71828: Add GPIO based run-level control for regulators Matti Vaittinen
                   ` (4 subsequent siblings)
  15 siblings, 0 replies; 19+ messages in thread
From: Matti Vaittinen @ 2019-11-16 19:00 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Lee Jones, Jacek Anaszewski, Pavel Machek, Dan Murphy,
	Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Mauro Carvalho Chehab, Jeff Kirsher, Wolfram Sang,
	Marek Szyprowski, Heiner Kallweit, Nicholas Mc Guire,
	Phil Edworthy, linux-leds, devicetree, linux-kernel, linux-doc,
	linux-clk, linux-gpio, linux-rtc

devm_gpiod_get_array and devm_gpiod_get_array_optional were missing
from the list. Add them.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
 Documentation/driver-api/driver-model/devres.rst | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/driver-api/driver-model/devres.rst b/Documentation/driver-api/driver-model/devres.rst
index 1b8302ba405b..b60d0702412d 100644
--- a/Documentation/driver-api/driver-model/devres.rst
+++ b/Documentation/driver-api/driver-model/devres.rst
@@ -267,6 +267,8 @@ DRM
 
 GPIO
   devm_gpiod_get()
+  devm_gpiod_get_array()
+  devm_gpiod_get_array_optional()
   devm_gpiod_get_index()
   devm_gpiod_get_index_optional()
   devm_gpiod_get_optional()
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply related	[flat|nested] 19+ messages in thread

* [PATCH v4 12/16] regulator: bd71828: Add GPIO based run-level control for regulators
  2019-11-16 18:55 [PATCH v4 00/16] Support ROHM BD71828 PMIC Matti Vaittinen
                   ` (10 preceding siblings ...)
  2019-11-16 19:00 ` [PATCH v4 11/16] docs: driver-model: Add missing managed GPIO array get functions Matti Vaittinen
@ 2019-11-16 19:00 ` Matti Vaittinen
  2019-11-16 19:01 ` [PATCH v4 13/16] rtc: bd70528 add BD71828 support Matti Vaittinen
                   ` (3 subsequent siblings)
  15 siblings, 0 replies; 19+ messages in thread
From: Matti Vaittinen @ 2019-11-16 19:00 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Lee Jones, Jacek Anaszewski, Pavel Machek, Dan Murphy,
	Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Mauro Carvalho Chehab, Jeff Kirsher, Wolfram Sang,
	Marek Szyprowski, Heiner Kallweit, Nicholas Mc Guire,
	Phil Edworthy, linux-leds, devicetree, linux-kernel, linux-doc,
	linux-clk, linux-gpio, linux-rtc

Bucks 1,2,6 and 7 on ROHM BD71828 can be either controlled as
individual regulartors - or they can be grouped to a group of
regulators that are controlled by 'run levels'. This can be
done via I2C. Each regulator can be assigned a voltage and
enable/disable status for each run-level. These statuses are
also changeable via I2C.

Run-levels can then be changed either by I2C or GPIO. This
control mechanism is selected by data in one time programmable
area (during production) and can't be changed later.

Allow:
 - configuring regulators to be controlled via run-levels
 - allow getting/setting the current run-level via in-kernel API
   using either GPIO or I2C underneath
 - Allow run-time changes to run-level voltages via in-kernel API
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
 drivers/regulator/bd71828-regulator.c | 561 +++++++++++++++++++++++++-
 include/linux/mfd/rohm-bd71828.h      |   5 +
 2 files changed, 556 insertions(+), 10 deletions(-)

diff --git a/drivers/regulator/bd71828-regulator.c b/drivers/regulator/bd71828-regulator.c
index b113cec41969..411e6a297da6 100644
--- a/drivers/regulator/bd71828-regulator.c
+++ b/drivers/regulator/bd71828-regulator.c
@@ -4,8 +4,10 @@
 //
 
 #include <linux/delay.h>
+#include <linux/device.h>
 #include <linux/err.h>
 #include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/interrupt.h>
 #include <linux/kernel.h>
 #include <linux/mfd/rohm-bd71828.h>
@@ -17,16 +19,37 @@
 #include <linux/regulator/machine.h>
 #include <linux/regulator/of_regulator.h>
 
+/* Drivers should not do this. But we provide this custom kernel interface
+ * for users to switch the run-level. Hence we need to get the rdev from
+ * struct regulator
+ */
+#include "internal.h"
+
+#define MAX_GPIO_DVS_BUCKS 4
+#define DVS_RUN_LEVELS 4
+#define BD71828_RUNLVL_DEFAULT_UV 500000
+
 struct reg_init {
 	unsigned int reg;
 	unsigned int mask;
 	unsigned int val;
 };
+
+struct run_lvl_ctrl {
+	unsigned int voltage;
+	bool enabled;
+};
+
 struct bd71828_regulator_data {
 	struct regulator_desc desc;
-	const struct rohm_dvs_config dvs;
+	struct rohm_dvs_config dvs;
 	const struct reg_init *reg_inits;
 	int reg_init_amnt;
+	struct run_lvl_ctrl run_lvl[DVS_RUN_LEVELS];
+	struct mutex dvs_lock;
+	struct gpio_descs *gps;
+	struct regmap *regmap;
+	bool allow_runlvl;
 };
 
 static const struct reg_init buck1_inits[] = {
@@ -41,6 +64,14 @@ static const struct reg_init buck1_inits[] = {
 	},
 };
 
+static const struct reg_init buck1_gpio_inits[] = {
+	{
+		.reg = BD71828_REG_PS_CTRL_1,
+		.mask = BD71828_MASK_DVS_BUCK1_CTRL,
+		.val = BD71828_DVS_BUCK1_USE_RUNLVL,
+	},
+};
+
 static const struct reg_init buck2_inits[] = {
 	{
 		.reg = BD71828_REG_PS_CTRL_1,
@@ -49,6 +80,14 @@ static const struct reg_init buck2_inits[] = {
 	},
 };
 
+static const struct reg_init buck2_gpio_inits[] = {
+	{
+		.reg = BD71828_REG_PS_CTRL_1,
+		.mask = BD71828_MASK_DVS_BUCK2_CTRL,
+		.val = BD71828_DVS_BUCK2_USE_RUNLVL,
+	},
+};
+
 static const struct reg_init buck6_inits[] = {
 	{
 		.reg = BD71828_REG_PS_CTRL_1,
@@ -57,6 +96,14 @@ static const struct reg_init buck6_inits[] = {
 	},
 };
 
+static const struct reg_init buck6_gpio_inits[] = {
+	{
+		.reg = BD71828_REG_PS_CTRL_1,
+		.mask = BD71828_MASK_DVS_BUCK6_CTRL,
+		.val = BD71828_DVS_BUCK6_USE_RUNLVL,
+	},
+};
+
 static const struct reg_init buck7_inits[] = {
 	{
 		.reg = BD71828_REG_PS_CTRL_1,
@@ -65,6 +112,14 @@ static const struct reg_init buck7_inits[] = {
 	},
 };
 
+static const struct reg_init buck7_gpio_inits[] = {
+	{
+		.reg = BD71828_REG_PS_CTRL_1,
+		.mask = BD71828_MASK_DVS_BUCK7_CTRL,
+		.val = BD71828_DVS_BUCK7_USE_RUNLVL,
+	},
+};
+
 static const struct regulator_linear_range bd71828_buck1267_volts[] = {
 	REGULATOR_LINEAR_RANGE(500000, 0x00, 0xef, 6250),
 	REGULATOR_LINEAR_RANGE(2000000, 0xf0, 0xff, 0),
@@ -155,6 +210,83 @@ static int buck_set_hw_dvs_levels(struct device_node *np,
 	return rohm_regulator_set_dvs_levels(&data->dvs, np, desc, cfg->regmap);
 }
 
+static int set_runlevel_voltage(struct regmap *regmap,
+				const struct regulator_desc *desc,
+				unsigned int uv, unsigned int level)
+{
+	int i, ret = -EINVAL;
+	/*
+	 * RUN level registers are next to vsel_reg. RUN0 reg is next, then
+	 * is the RUN 1 reg and so on...
+	 */
+	u8 reg = desc->vsel_reg + level + 1;
+	u8 mask = BD71828_MASK_BUCK1267_VOLT;
+
+	for (i = 0; i < desc->n_voltages; i++) {
+		ret = regulator_desc_list_voltage_linear_range(desc, i);
+		if (ret < 0)
+			continue;
+		if (ret == uv) {
+			i <<= ffs(desc->vsel_mask) - 1;
+			ret = regmap_update_bits(regmap, reg, mask, i);
+			break;
+		}
+	}
+	return ret;
+}
+
+static int buck_set_runlvl_hw_dvs_levels(struct device_node *np,
+				       const struct regulator_desc *desc,
+				       struct regulator_config *cfg)
+{
+	struct bd71828_regulator_data *data;
+	/* Default to 'disabled' (0 uV) if no property found */
+	uint32_t uv[DVS_RUN_LEVELS] = {0};
+	int i, ret;
+	const char *prop = "rohm,dvs-runlevel-microvolts";
+	/* On BD71828 the RUN level control reg is next to enable reg */
+	u8 en_reg = desc->enable_reg + 1;
+	u8 en_masks[DVS_RUN_LEVELS] = { BD71828_MASK_RUN0_EN,
+					BD71828_MASK_RUN1_EN,
+					BD71828_MASK_RUN2_EN,
+					BD71828_MASK_RUN3_EN };
+
+	data = container_of(desc, struct bd71828_regulator_data, desc);
+
+	ret = of_property_read_variable_u32_array(np, prop, uv, 1,
+						  DVS_RUN_LEVELS);
+	if (ret < 0 && ret != -EINVAL)
+		return ret;
+
+	mutex_lock(&data->dvs_lock);
+	for (i = 0; i < DVS_RUN_LEVELS; i++) {
+		if (uv[i]) {
+			data->run_lvl[i].voltage = uv[i];
+			data->run_lvl[i].enabled = true;
+
+			ret = set_runlevel_voltage(cfg->regmap, desc, uv[i], i);
+			if (ret)
+				goto unlock_out;
+
+			ret = regmap_update_bits(cfg->regmap, en_reg,
+						 en_masks[i], en_masks[i]);
+		} else {
+			data->run_lvl[i].voltage = BD71828_RUNLVL_DEFAULT_UV;
+			ret = regmap_update_bits(cfg->regmap, en_reg,
+						 en_masks[i], 0);
+		}
+		if (ret)
+			goto unlock_out;
+	}
+
+	ret = rohm_regulator_set_dvs_levels(&data->dvs, np, desc, cfg->regmap);
+
+unlock_out:
+	mutex_unlock(&data->dvs_lock);
+
+	return ret;
+}
+
 static int ldo6_parse_dt(struct device_node *np,
 			 const struct regulator_desc *desc,
 			 struct regulator_config *cfg)
@@ -189,6 +321,265 @@ static int ldo6_parse_dt(struct device_node *np,
 	return 0;
 }
 
+static int bd71828_dvs_gpio_set_run_level(struct bd71828_regulator_data *rd,
+					  int val)
+{
+	DECLARE_BITMAP(values, 2);
+
+	if (rd->gps->ndescs != 2)
+		return -EINVAL;
+
+	if (val < 0 || val > 3)
+		return -EINVAL;
+
+	values[0] = val;
+
+	return gpiod_set_array_value_cansleep(rd->gps->ndescs, rd->gps->desc,
+				     rd->gps->info, values);
+}
+
+/* Get current run level when RUN levels are controlled using I2C */
+static int bd71828_dvs_i2c_set_run_level(struct regmap *regmap,
+					 int lvl)
+{
+	unsigned int reg;
+
+	reg = lvl << (ffs(BD71828_MASK_RUN_LVL_CTRL) - 1);
+
+	return regmap_update_bits(regmap, BD71828_REG_PS_CTRL_3,
+				  BD71828_MASK_RUN_LVL_CTRL, reg);
+}
+/* Get current run level when RUN levels are controlled using I2C */
+static int bd71828_dvs_i2c_get_run_level(struct regmap *regmap,
+					 struct bd71828_regulator_data *rd)
+{
+	int ret;
+	unsigned int val;
+
+	ret = regmap_read(regmap, BD71828_REG_PS_CTRL_3, &val);
+	if (ret)
+		return ret;
+
+	ret = (val & BD71828_MASK_RUN_LVL_CTRL);
+	ret >>= ffs(BD71828_MASK_RUN_LVL_CTRL) - 1;
+
+	return ret;
+}
+
+/* Get current RUN level when run levels are controlled by GPIO */
+static int bd71828_dvs_gpio_get_run_level(struct bd71828_regulator_data *rd)
+{
+	int run_level;
+	int ret;
+	DECLARE_BITMAP(values, 2);
+
+	values[0] = 0;
+
+	if (rd->gps->ndescs != 2)
+		return -EINVAL;
+
+	ret = gpiod_get_array_value_cansleep(rd->gps->ndescs, rd->gps->desc,
+				     rd->gps->info, values);
+	if (ret)
+		return ret;
+
+	run_level = values[0];
+
+	return run_level;
+}
+
+/*
+ * To be used when BD71828 regulator is controlled by RUN levels
+ * via I2C instead of GPIO
+ */
+static int bd71828_dvs_i2c_is_enabled(struct regulator_dev *rdev)
+{
+	struct bd71828_regulator_data *data = rdev_get_drvdata(rdev);
+	int ret;
+
+	mutex_lock(&data->dvs_lock);
+	ret = bd71828_dvs_i2c_get_run_level(rdev->regmap, data);
+	if (ret < 0)
+		goto unlock_out;
+
+	ret = data->run_lvl[ret].enabled;
+
+unlock_out:
+	mutex_unlock(&data->dvs_lock);
+
+	return ret;
+}
+
+/*
+ * To be used when BD71828 regulator is controlled by RUN levels
+ * via GPIO
+ */
+static int bd71828_dvs_gpio_is_enabled(struct regulator_dev *rdev)
+{
+	struct bd71828_regulator_data *data = rdev_get_drvdata(rdev);
+	int ret;
+
+	mutex_lock(&data->dvs_lock);
+	ret = bd71828_dvs_gpio_get_run_level(data);
+	if (ret < 0 || ret >= DVS_RUN_LEVELS)
+		goto unlock_out;
+
+	ret = data->run_lvl[ret].enabled;
+
+unlock_out:
+	mutex_unlock(&data->dvs_lock);
+
+	return ret;
+}
+
+/*
+ * To be used when BD71828 regulator is controlled by RUN levels
+ * via I2C instead of GPIO
+ */
+static int bd71828_dvs_i2c_get_voltage(struct regulator_dev *rdev)
+{
+	int ret;
+	struct bd71828_regulator_data *data = rdev_get_drvdata(rdev);
+
+	mutex_lock(&data->dvs_lock);
+	ret = bd71828_dvs_i2c_get_run_level(rdev->regmap, data);
+	if (ret < 0)
+		goto unlock_out;
+
+	ret = data->run_lvl[ret].voltage;
+
+unlock_out:
+	mutex_unlock(&data->dvs_lock);
+
+	return ret;
+}
+
+/*
+ * To be used when BD71828 regulator is controlled by RUN levels
+ * via GPIO
+ */
+static int bd71828_dvs_gpio_get_voltage(struct regulator_dev *rdev)
+{
+	int ret;
+	struct bd71828_regulator_data *data = rdev_get_drvdata(rdev);
+
+	mutex_lock(&data->dvs_lock);
+	ret = bd71828_dvs_gpio_get_run_level(data);
+	if (ret < 0 || DVS_RUN_LEVELS <= ret)
+		goto unlock_out;
+
+	ret = data->run_lvl[ret].voltage;
+
+unlock_out:
+	mutex_unlock(&data->dvs_lock);
+
+	return ret;
+}
+
+/**
+ * bd71828_set_runlevel_voltage - change run-level voltage
+ *
+ * @regulator:  pointer to regulator for which the run-level voltage is changed
+ * @uv:		New voltage for run-level in micro volts
+ * @level:	run-level for which the voltage is to be changed
+ *
+ * Changes the run-level voltage for given regulator
+ */
+int bd71828_set_runlevel_voltage(struct regulator *regulator, unsigned int uv,
+				 unsigned int level)
+{
+	struct regulator_dev *rdev = regulator->rdev;
+	struct bd71828_regulator_data *data = rdev_get_drvdata(rdev);
+	int ret;
+
+	if (!data || !data->allow_runlvl)
+		return -EINVAL;
+
+	mutex_lock(&data->dvs_lock);
+	ret = set_runlevel_voltage(rdev->regmap, rdev->desc, uv, level);
+	mutex_unlock(&data->dvs_lock);
+
+	return ret;
+}
+EXPORT_SYMBOL(bd71828_set_runlevel_voltage);
+
+/**
+ * bd71828_set_runlevel - change system run-level.
+ *
+ * @regulator:	pointer to one of the BD71828 regulators obtained by
+ *		call to regulator_get
+ * @level:	New run-level the system should enter
+ *
+ * Changes the system to run-level which was given as argument. This
+ * operation will change state of all regulators which are set to be
+ * controlled by run-levels. Note that 'regulator' must point to a
+ * regulator which is controlled by run-levels.
+ */
+int bd71828_set_runlevel(struct regulator *regulator, unsigned int level)
+{
+	struct regulator_dev *rdev = regulator->rdev;
+	struct bd71828_regulator_data *rd = rdev_get_drvdata(rdev);
+
+	if (!rd)
+		return -ENOENT;
+
+	if (!rd || !rd->allow_runlvl)
+		return -EINVAL;
+
+	if (rd->gps)
+		return bd71828_dvs_gpio_set_run_level(rd, level);
+
+	return bd71828_dvs_i2c_set_run_level(rd->regmap, level);
+}
+EXPORT_SYMBOL(bd71828_set_runlevel);
+
+/**
+ * bd71828_get_runlevel - get the current system run-level.
+ *
+ * @regulator:	pointer to one of the BD71828 regulators obtained by
+ *		call to regulator_get
+ * @level:	Pointer to value where current run-level is stored
+ *
+ * Returns the current system run-level. Note that 'regulator' must
+ * point to a regulator which is controlled by run-levels.
+ */
+int bd71828_get_runlevel(struct regulator *regulator, unsigned int *level)
+{
+	struct regulator_dev *rdev = regulator->rdev;
+	struct bd71828_regulator_data *rd = rdev_get_drvdata(rdev);
+	int ret;
+
+	if (!rd)
+		return -ENOENT;
+
+	if (!rd || !rd->allow_runlvl)
+		return -EINVAL;
+
+	if (!rd->gps)
+		ret = bd71828_dvs_i2c_get_run_level(rd->regmap, rd);
+	else
+		ret = bd71828_dvs_gpio_get_run_level(rd);
+
+	if (ret < 0)
+		return ret;
+
+	*level = (unsigned int) ret;
+
+	return 0;
+}
+EXPORT_SYMBOL(bd71828_get_runlevel);
+
+
+static const struct regulator_ops dvs_buck_gpio_ops = {
+	.is_enabled = bd71828_dvs_gpio_is_enabled,
+	.get_voltage = bd71828_dvs_gpio_get_voltage,
+};
+
+static const struct regulator_ops dvs_buck_i2c_ops = {
+	.is_enabled = bd71828_dvs_i2c_is_enabled,
+	.get_voltage = bd71828_dvs_i2c_get_voltage,
+};
+
 static const struct regulator_ops bd71828_buck_ops = {
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
@@ -773,6 +1164,127 @@ static const struct bd71828_regulator_data bd71828_rdata[] = {
 	},
 };
 
+struct bd71828_gpio_cfg {
+	bool use_gpio;
+	unsigned int runlvl;
+	struct gpio_descs *gps;
+};
+
+static void mark_regulator_runlvl_controlled(struct device *dev,
+					     struct device_node *np,
+					     struct bd71828_gpio_cfg *g)
+{
+	int i;
+
+	for (i = 1; i <= ARRAY_SIZE(bd71828_rdata); i++) {
+		if (!of_node_name_eq(np, bd71828_rdata[i-1].desc.of_match))
+			continue;
+		switch (i) {
+		case 1:
+		case 2:
+		case 6:
+		case 7:
+			g->runlvl |= 1 << (i - 1);
+			dev_dbg(dev, "buck %d runlevel controlled\n", i);
+			break;
+		default:
+			dev_err(dev,
+				"Only bucks 1,2,6,7 support run-level dvs\n");
+			break;
+		}
+	}
+}
+
+static int get_runcontrolled_bucks_dt(struct device *dev,
+				      struct bd71828_gpio_cfg *g)
+{
+	struct device_node *np;
+	struct device_node *nproot = dev->of_node;
+	const char *prop = "rohm,dvs-runlvl-ctrl";
+
+	g->runlvl = 0;
+
+	nproot = of_get_child_by_name(nproot, "regulators");
+	if (!nproot) {
+		dev_err(dev, "failed to find regulators node\n");
+		return -ENODEV;
+	}
+	for_each_child_of_node(nproot, np)
+		if (of_property_read_bool(np, prop))
+			mark_regulator_runlvl_controlled(dev, np, g);
+
+	of_node_put(nproot);
+	return 0;
+}
+
+static int check_dt_for_gpio_controls(struct device *d,
+				      struct bd71828_gpio_cfg *g)
+{
+	int ret;
+
+	ret = get_runcontrolled_bucks_dt(d, g);
+	if (ret)
+		return ret;
+
+	g->use_gpio = false;
+
+	/* If the run level control is not requested by any bucks we're done */
+	if (!g->runlvl)
+		return 0;
+
+	g->gps = devm_gpiod_get_parent_array(d, "rohm,dvs-vsel", GPIOD_OUT_LOW);
+
+	if (IS_ERR(g->gps)) {
+		ret = PTR_ERR(g->gps);
+		if (ret == -ENOENT)
+			return 0;
+		return ret;
+	}
+
+	if (g->gps->ndescs != 2)
+		return -ENOENT;
+
+	g->use_gpio = true;
+
+	return 0;
+}
+
+static void set_buck_runlvl_controlled(struct rohm_regmap_dev *bd71828,
+				      struct bd71828_regulator_data *rd,
+				      struct bd71828_gpio_cfg *g)
+{
+	switch (rd->desc.id) {
+	case BD71828_BUCK1:
+		rd->reg_inits = buck1_gpio_inits;
+		break;
+	case BD71828_BUCK2:
+		rd->reg_inits = buck2_gpio_inits;
+		break;
+	case BD71828_BUCK6:
+		rd->reg_inits = buck6_gpio_inits;
+		break;
+	case BD71828_BUCK7:
+		rd->reg_inits = buck7_gpio_inits;
+		break;
+	default:
+		return;
+	}
+
+	/*
+	 * Disallow setters. Get voltages/enable states based
+	 * on current RUN level
+	 */
+	rd->allow_runlvl = true;
+
+	if (g->use_gpio) {
+		rd->gps = g->gps;
+		rd->desc.ops = &dvs_buck_gpio_ops;
+	} else {
+		rd->desc.ops = &dvs_buck_i2c_ops;
+	}
+	rd->desc.of_parse_cb = buck_set_runlvl_hw_dvs_levels;
+}
+
 static int bd71828_probe(struct platform_device *pdev)
 {
 	struct rohm_regmap_dev *bd71828;
@@ -780,6 +1292,8 @@ static int bd71828_probe(struct platform_device *pdev)
 	struct regulator_config config = {
 		.dev = pdev->dev.parent,
 	};
+	struct bd71828_gpio_cfg gcfg = {0};
+	struct bd71828_regulator_data *rd;
 
 	bd71828 = dev_get_drvdata(pdev->dev.parent);
 	if (!bd71828) {
@@ -787,30 +1301,57 @@ static int bd71828_probe(struct platform_device *pdev)
 		return -EINVAL;
 	}
 
+	ret = check_dt_for_gpio_controls(pdev->dev.parent, &gcfg);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to get DVS gpio resources\n");
+		return ret;
+	}
+
+	/*
+	 * Allocate device data to allow controlling more than one PMICs
+	 */
+	rd = devm_kmalloc_array(&pdev->dev, ARRAY_SIZE(bd71828_rdata),
+				sizeof(*rd), GFP_KERNEL);
+	if (!rd)
+		return -ENOMEM;
+
+	dev_set_drvdata(&pdev->dev, rd);
+
+	for (i = 0; i < ARRAY_SIZE(bd71828_rdata); i++) {
+		/* Use bd71828_rdata as template */
+		rd[i] = bd71828_rdata[i];
+
+		mutex_init(&rd[i].dvs_lock);
+		if (gcfg.runlvl & (1 << i))
+			set_buck_runlvl_controlled(bd71828, &rd[i], &gcfg);
+
+		rd[i].regmap = bd71828->regmap;
+	}
+
 	config.regmap = bd71828->regmap;
 
 	for (i = 0; i < ARRAY_SIZE(bd71828_rdata); i++) {
 		struct regulator_dev *rdev;
-		const struct bd71828_regulator_data *rd;
 
-		rd = &bd71828_rdata[i];
+		config.driver_data = &rd[i];
+
 		rdev = devm_regulator_register(&pdev->dev,
-					       &rd->desc, &config);
+					       &rd[i].desc, &config);
 		if (IS_ERR(rdev)) {
 			dev_err(&pdev->dev,
 				"failed to register %s regulator\n",
-				rd->desc.name);
+				rd[i].desc.name);
 			return PTR_ERR(rdev);
 		}
-		for (j = 0; j < rd->reg_init_amnt; j++) {
+		for (j = 0; j < rd[i].reg_init_amnt; j++) {
 			ret = regmap_update_bits(bd71828->regmap,
-						 rd->reg_inits[j].reg,
-						 rd->reg_inits[j].mask,
-						 rd->reg_inits[j].val);
+						 rd[i].reg_inits[j].reg,
+						 rd[i].reg_inits[j].mask,
+						 rd[i].reg_inits[j].val);
 			if (ret) {
 				dev_err(&pdev->dev,
 					"regulator %s init failed\n",
-					rd->desc.name);
+					rd[i].desc.name);
 				return ret;
 			}
 		}
diff --git a/include/linux/mfd/rohm-bd71828.h b/include/linux/mfd/rohm-bd71828.h
index d013e03f742d..fc0955f0662c 100644
--- a/include/linux/mfd/rohm-bd71828.h
+++ b/include/linux/mfd/rohm-bd71828.h
@@ -418,4 +418,9 @@ enum {
 #define BD71828_OUT_TYPE_OPEN_DRAIN			0x0
 #define BD71828_OUT_TYPE_CMOS				0x2
 
+int bd71828_set_runlevel_voltage(struct regulator *regulator, unsigned int uv,
+				 unsigned int level);
+int bd71828_set_runlevel(struct regulator *regulator, unsigned int level);
+int bd71828_get_runlevel(struct regulator *regulator, unsigned int *level);
+
 #endif /* __LINUX_MFD_BD71828_H__ */
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply related	[flat|nested] 19+ messages in thread

* [PATCH v4 13/16] rtc: bd70528 add BD71828 support
  2019-11-16 18:55 [PATCH v4 00/16] Support ROHM BD71828 PMIC Matti Vaittinen
                   ` (11 preceding siblings ...)
  2019-11-16 19:00 ` [PATCH v4 12/16] regulator: bd71828: Add GPIO based run-level control for regulators Matti Vaittinen
@ 2019-11-16 19:01 ` Matti Vaittinen
  2019-11-16 19:01 ` [PATCH v4 14/16] gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs Matti Vaittinen
                   ` (2 subsequent siblings)
  15 siblings, 0 replies; 19+ messages in thread
From: Matti Vaittinen @ 2019-11-16 19:01 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Lee Jones, Jacek Anaszewski, Pavel Machek, Dan Murphy,
	Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Mauro Carvalho Chehab, Jeff Kirsher, Wolfram Sang,
	Marek Szyprowski, Heiner Kallweit, Nicholas Mc Guire,
	Phil Edworthy, linux-leds, devicetree, linux-kernel, linux-doc,
	linux-clk, linux-gpio, linux-rtc

ROHM BD71828 PMIC RTC block is from many parts similar to one
on BD70528. Support BD71828 RTC using BD70528 RTC driver and
avoid re-inventing the wheel.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
 drivers/rtc/Kconfig              |   3 +-
 drivers/rtc/rtc-bd70528.c        | 167 ++++++++++++++++++++++++++++---
 include/linux/mfd/rohm-bd70528.h |  13 +--
 include/linux/mfd/rohm-bd71828.h |   4 +-
 include/linux/mfd/rohm-shared.h  |  27 +++++
 5 files changed, 185 insertions(+), 29 deletions(-)
 create mode 100644 include/linux/mfd/rohm-shared.h

diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index 1adf9f815652..d03636ec7311 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -509,12 +509,13 @@ config RTC_DRV_M41T80_WDT
 	help
 	  If you say Y here you will get support for the
 	  watchdog timer in the ST M41T60 and M41T80 RTC chips series.
+
 config RTC_DRV_BD70528
 	tristate "ROHM BD70528 PMIC RTC"
 	depends on MFD_ROHM_BD70528 && (BD70528_WATCHDOG || !BD70528_WATCHDOG)
 	help
 	  If you say Y here you will get support for the RTC
-	  on ROHM BD70528 Power Management IC.
+	  block on ROHM BD70528 and BD71828 Power Management IC.
 
 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-bd70528.
diff --git a/drivers/rtc/rtc-bd70528.c b/drivers/rtc/rtc-bd70528.c
index 7744333b0f40..09524b2712ba 100644
--- a/drivers/rtc/rtc-bd70528.c
+++ b/drivers/rtc/rtc-bd70528.c
@@ -6,6 +6,7 @@
 
 #include <linux/bcd.h>
 #include <linux/mfd/rohm-bd70528.h>
+#include <linux/mfd/rohm-bd71828.h>
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/platform_device.h>
@@ -15,7 +16,7 @@
 /*
  * We read regs RTC_SEC => RTC_YEAR
  * this struct is ordered according to chip registers.
- * Keep it u8 only to avoid padding issues.
+ * Keep it u8 only (or packed) to avoid padding issues.
  */
 struct bd70528_rtc_day {
 	u8 sec;
@@ -36,6 +37,13 @@ struct bd70528_rtc_wake {
 	u8 ctrl;
 } __packed;
 
+struct bd71828_rtc_alm {
+	struct bd70528_rtc_data alm0;
+	struct bd70528_rtc_data alm1;
+	u8 alm_mask;
+	u8 alm1_mask;
+} __packed;
+
 struct bd70528_rtc_alm {
 	struct bd70528_rtc_data data;
 	u8 alm_mask;
@@ -45,6 +53,8 @@ struct bd70528_rtc_alm {
 struct bd70528_rtc {
 	struct rohm_regmap_dev *mfd;
 	struct device *dev;
+	u8 reg_time_start;
+	bool has_rtc_timers;
 };
 
 static int bd70528_set_wake(struct rohm_regmap_dev *bd70528,
@@ -152,12 +162,18 @@ static int bd70528_set_rtc_based_timers(struct bd70528_rtc *r, int new_state,
 static int bd70528_re_enable_rtc_based_timers(struct bd70528_rtc *r,
 					      int old_state)
 {
+	if (!r->has_rtc_timers)
+		return 0;
+
 	return bd70528_set_rtc_based_timers(r, old_state, NULL);
 }
 
 static int bd70528_disable_rtc_based_timers(struct bd70528_rtc *r,
 					    int *old_state)
 {
+	if (!r->has_rtc_timers)
+		return 0;
+
 	return bd70528_set_rtc_based_timers(r, 0, old_state);
 }
 
@@ -213,6 +229,36 @@ static inline void rtc2tm(struct bd70528_rtc_data *r, struct rtc_time *t)
 	t->tm_wday = bcd2bin(r->week & BD70528_MASK_RTC_WEEK);
 }
 
+static int bd71828_set_alarm(struct device *dev, struct rtc_wkalrm *a)
+{
+	int ret;
+	struct bd71828_rtc_alm alm;
+	struct bd70528_rtc *r = dev_get_drvdata(dev);
+	struct rohm_regmap_dev *bd71828 = r->mfd;
+
+	ret = regmap_bulk_read(bd71828->regmap, BD71828_REG_RTC_ALM_START,
+			       &alm, sizeof(alm));
+	if (ret) {
+		dev_err(dev, "Failed to read alarm regs\n");
+		return ret;
+	}
+
+	tm2rtc(&a->time, &alm.alm0);
+
+	if (!a->enabled)
+		alm.alm_mask &= ~BD70528_MASK_ALM_EN;
+	else
+		alm.alm_mask |= BD70528_MASK_ALM_EN;
+
+	ret = regmap_bulk_write(bd71828->regmap, BD71828_REG_RTC_ALM_START,
+				&alm, sizeof(alm));
+	if (ret)
+		dev_err(dev, "Failed to set alarm time\n");
+
+	return ret;
+
+}
+
 static int bd70528_set_alarm(struct device *dev, struct rtc_wkalrm *a)
 {
 	struct bd70528_rtc_wake wake;
@@ -261,6 +307,30 @@ static int bd70528_set_alarm(struct device *dev, struct rtc_wkalrm *a)
 	return ret;
 }
 
+static int bd71828_read_alarm(struct device *dev, struct rtc_wkalrm *a)
+{
+	int ret;
+	struct bd71828_rtc_alm alm;
+	struct bd70528_rtc *r = dev_get_drvdata(dev);
+	struct rohm_regmap_dev *bd71828 = r->mfd;
+
+	ret = regmap_bulk_read(bd71828->regmap, BD71828_REG_RTC_ALM_START,
+			       &alm, sizeof(alm));
+	if (ret) {
+		dev_err(dev, "Failed to read alarm regs\n");
+		return ret;
+	}
+
+	rtc2tm(&alm.alm0, &a->time);
+	a->time.tm_mday = -1;
+	a->time.tm_mon = -1;
+	a->time.tm_year = -1;
+	a->enabled = !!(alm.alm_mask & BD70528_MASK_ALM_EN);
+	a->pending = 0;
+
+	return 0;
+}
+
 static int bd70528_read_alarm(struct device *dev, struct rtc_wkalrm *a)
 {
 	struct bd70528_rtc_alm alm;
@@ -297,7 +367,7 @@ static int bd70528_set_time_locked(struct device *dev, struct rtc_time *t)
 		return ret;
 
 	tmpret = regmap_bulk_read(bd70528->regmap,
-				  BD70528_REG_RTC_START, &rtc_data,
+				  r->reg_time_start, &rtc_data,
 				  sizeof(rtc_data));
 	if (tmpret) {
 		dev_err(dev, "Failed to read RTC time registers\n");
@@ -306,7 +376,7 @@ static int bd70528_set_time_locked(struct device *dev, struct rtc_time *t)
 	tm2rtc(t, &rtc_data);
 
 	tmpret = regmap_bulk_write(bd70528->regmap,
-				   BD70528_REG_RTC_START, &rtc_data,
+				   r->reg_time_start, &rtc_data,
 				   sizeof(rtc_data));
 	if (tmpret) {
 		dev_err(dev, "Failed to set RTC time\n");
@@ -321,6 +391,11 @@ static int bd70528_set_time_locked(struct device *dev, struct rtc_time *t)
 	return ret;
 }
 
+static int bd71828_set_time(struct device *dev, struct rtc_time *t)
+{
+	return bd70528_set_time_locked(dev, t);
+}
+
 static int bd70528_set_time(struct device *dev, struct rtc_time *t)
 {
 	int ret;
@@ -341,7 +416,7 @@ static int bd70528_get_time(struct device *dev, struct rtc_time *t)
 
 	/* read the RTC date and time registers all at once */
 	ret = regmap_bulk_read(bd70528->regmap,
-			       BD70528_REG_RTC_START, &rtc_data,
+			       r->reg_time_start, &rtc_data,
 			       sizeof(rtc_data));
 	if (ret) {
 		dev_err(dev, "Failed to read RTC time (err %d)\n", ret);
@@ -378,6 +453,23 @@ static int bd70528_alm_enable(struct device *dev, unsigned int enabled)
 	return ret;
 }
 
+static int bd71828_alm_enable(struct device *dev, unsigned int enabled)
+{
+	int ret;
+	struct bd70528_rtc *r = dev_get_drvdata(dev);
+	unsigned int enableval = BD70528_MASK_ALM_EN;
+
+	if (!enabled)
+		enableval = 0;
+
+	ret = regmap_update_bits(r->mfd->regmap, BD71828_REG_RTC_ALM0_MASK,
+				 BD70528_MASK_ALM_EN, enableval);
+	if (ret)
+		dev_err(dev, "Failed to change alarm state\n");
+
+	return ret;
+}
+
 static const struct rtc_class_ops bd70528_rtc_ops = {
 	.read_time		= bd70528_get_time,
 	.set_time		= bd70528_set_time,
@@ -386,6 +478,14 @@ static const struct rtc_class_ops bd70528_rtc_ops = {
 	.alarm_irq_enable	= bd70528_alm_enable,
 };
 
+static const struct rtc_class_ops bd71828_rtc_ops = {
+	.read_time		= bd70528_get_time,
+	.set_time		= bd71828_set_time,
+	.read_alarm		= bd71828_read_alarm,
+	.set_alarm		= bd71828_set_alarm,
+	.alarm_irq_enable	= bd71828_alm_enable,
+};
+
 static irqreturn_t alm_hndlr(int irq, void *data)
 {
 	struct rtc_device *rtc = data;
@@ -397,11 +497,16 @@ static irqreturn_t alm_hndlr(int irq, void *data)
 static int bd70528_probe(struct platform_device *pdev)
 {
 	struct bd70528_rtc *bd_rtc;
+	const struct rtc_class_ops *rtc_ops;
 	struct rohm_regmap_dev *mfd;
+	const char *irq_name;
 	int ret;
 	struct rtc_device *rtc;
 	int irq;
 	unsigned int hr;
+	bool enable_main_irq = false;
+	u8 hour_reg;
+	enum rohm_chip_type chip = platform_get_device_id(pdev)->driver_data;
 
 	mfd = dev_get_drvdata(pdev->dev.parent);
 	if (!mfd) {
@@ -415,13 +520,36 @@ static int bd70528_probe(struct platform_device *pdev)
 	bd_rtc->mfd = mfd;
 	bd_rtc->dev = &pdev->dev;
 
-	irq = platform_get_irq_byname(pdev, "bd70528-rtc-alm");
-	if (irq < 0)
+	switch (chip) {
+	case ROHM_CHIP_TYPE_BD70528:
+		irq_name = "bd70528-rtc-alm";
+		bd_rtc->has_rtc_timers = true;
+		bd_rtc->reg_time_start = BD70528_REG_RTC_START;
+		hour_reg = BD70528_REG_RTC_HOUR;
+		enable_main_irq = true;
+		rtc_ops = &bd70528_rtc_ops;
+		break;
+	case ROHM_CHIP_TYPE_BD71828:
+		irq_name = "bd71828-rtc-alm-0";
+		bd_rtc->reg_time_start = BD71828_REG_RTC_START;
+		hour_reg = BD71828_REG_RTC_HOUR;
+		rtc_ops = &bd71828_rtc_ops;
+		break;
+	default:
+		dev_err(&pdev->dev, "Unknown chip\n");
+		return -ENOENT;
+	}
+
+	irq = platform_get_irq_byname(pdev, irq_name);
+
+	if (irq < 0) {
+		dev_err(&pdev->dev, "Failed to get irq\n");
 		return irq;
+	}
 
 	platform_set_drvdata(pdev, bd_rtc);
 
-	ret = regmap_read(mfd->regmap, BD70528_REG_RTC_HOUR, &hr);
+	ret = regmap_read(mfd->regmap, hour_reg, &hr);
 
 	if (ret) {
 		dev_err(&pdev->dev, "Failed to reag RTC clock\n");
@@ -431,10 +559,10 @@ static int bd70528_probe(struct platform_device *pdev)
 	if (!(hr & BD70528_MASK_RTC_HOUR_24H)) {
 		struct rtc_time t;
 
-		ret = bd70528_get_time(&pdev->dev, &t);
+		ret = rtc_ops->read_time(&pdev->dev, &t);
 
 		if (!ret)
-			ret = bd70528_set_time(&pdev->dev, &t);
+			ret = rtc_ops->set_time(&pdev->dev, &t);
 
 		if (ret) {
 			dev_err(&pdev->dev,
@@ -454,7 +582,7 @@ static int bd70528_probe(struct platform_device *pdev)
 
 	rtc->range_min = RTC_TIMESTAMP_BEGIN_2000;
 	rtc->range_max = RTC_TIMESTAMP_END_2099;
-	rtc->ops = &bd70528_rtc_ops;
+	rtc->ops = rtc_ops;
 
 	/* Request alarm IRQ prior to registerig the RTC */
 	ret = devm_request_threaded_irq(&pdev->dev, irq, NULL, &alm_hndlr,
@@ -468,26 +596,35 @@ static int bd70528_probe(struct platform_device *pdev)
 	 *  leave them enabled as irq-controller should disable irqs
 	 *  from sub-registers when IRQ is disabled or freed.
 	 */
-	ret = regmap_update_bits(mfd->regmap,
+	if (enable_main_irq) {
+		ret = regmap_update_bits(mfd->regmap,
 				 BD70528_REG_INT_MAIN_MASK,
 				 BD70528_INT_RTC_MASK, 0);
-	if (ret) {
-		dev_err(&pdev->dev, "Failed to enable RTC interrupts\n");
-		return ret;
+		if (ret) {
+			dev_err(&pdev->dev, "Failed to enable RTC interrupts\n");
+			return ret;
+		}
 	}
 
 	return rtc_register_device(rtc);
 }
+static const struct platform_device_id bd718x7_rtc_id[] = {
+	{ "bd70528-rtc", ROHM_CHIP_TYPE_BD70528 },
+	{ "bd71828-rtc", ROHM_CHIP_TYPE_BD71828 },
+	{ },
+};
+MODULE_DEVICE_TABLE(platform, bd718x7_rtc_id);
 
 static struct platform_driver bd70528_rtc = {
 	.driver = {
 		.name = "bd70528-rtc"
 	},
 	.probe = bd70528_probe,
+	.id_table = bd718x7_rtc_id,
 };
 
 module_platform_driver(bd70528_rtc);
 
 MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
-MODULE_DESCRIPTION("BD70528 RTC driver");
+MODULE_DESCRIPTION("ROHM BD70528 and BD71828 PMIC RTC driver");
 MODULE_LICENSE("GPL");
diff --git a/include/linux/mfd/rohm-bd70528.h b/include/linux/mfd/rohm-bd70528.h
index 2ad2320d0a96..a57af878fd0c 100644
--- a/include/linux/mfd/rohm-bd70528.h
+++ b/include/linux/mfd/rohm-bd70528.h
@@ -7,6 +7,7 @@
 #include <linux/bits.h>
 #include <linux/device.h>
 #include <linux/mfd/rohm-generic.h>
+#include <linux/mfd/rohm-shared.h>
 #include <linux/regmap.h>
 
 enum {
@@ -307,17 +308,6 @@ enum {
 
 /* RTC masks to mask out reserved bits */
 
-#define BD70528_MASK_RTC_SEC		0x7f
-#define BD70528_MASK_RTC_MINUTE		0x7f
-#define BD70528_MASK_RTC_HOUR_24H	0x80
-#define BD70528_MASK_RTC_HOUR_PM	0x20
-#define BD70528_MASK_RTC_HOUR		0x1f
-#define BD70528_MASK_RTC_DAY		0x3f
-#define BD70528_MASK_RTC_WEEK		0x07
-#define BD70528_MASK_RTC_MONTH		0x1f
-#define BD70528_MASK_RTC_YEAR		0xff
-#define BD70528_MASK_RTC_COUNT_L	0x7f
-
 #define BD70528_MASK_ELAPSED_TIMER_EN	0x1
 /* Mask second, min and hour fields
  * HW would support ALM irq for over 24h
@@ -326,7 +316,6 @@ enum {
  * wake-up we limit ALM to 24H and only
  * unmask sec, min and hour
  */
-#define BD70528_MASK_ALM_EN		0x7
 #define BD70528_MASK_WAKE_EN		0x1
 
 /* WDT masks */
diff --git a/include/linux/mfd/rohm-bd71828.h b/include/linux/mfd/rohm-bd71828.h
index fc0955f0662c..093662f3e867 100644
--- a/include/linux/mfd/rohm-bd71828.h
+++ b/include/linux/mfd/rohm-bd71828.h
@@ -5,6 +5,7 @@
 #define __LINUX_MFD_BD71828_H__
 
 #include <linux/mfd/rohm-generic.h>
+#include <linux/mfd/rohm-shared.h>
 
 /* Regulator IDs */
 enum {
@@ -160,6 +161,7 @@ enum {
 #define BD71828_REG_RTC_YEAR		0x52
 
 #define BD71828_REG_RTC_ALM0_SEC	0x53
+#define BD71828_REG_RTC_ALM_START	BD71828_REG_RTC_ALM0_SEC
 #define BD71828_REG_RTC_ALM0_MINUTE	0x54
 #define BD71828_REG_RTC_ALM0_HOUR	0x55
 #define BD71828_REG_RTC_ALM0_WEEK	0x56
@@ -178,6 +180,7 @@ enum {
 #define BD71828_REG_RTC_ALM1_MASK	0x62
 
 #define BD71828_REG_RTC_ALM2		0x63
+#define BD71828_REG_RTC_START		BD71828_REG_RTC_SEC
 
 /* Charger/Battey */
 #define BD71828_REG_CHG_STATE		0x65
@@ -204,7 +207,6 @@ enum {
 #define BD71828_REG_INT_MASK_TEMP	0xdd
 #define BD71828_REG_INT_MASK_RTC	0xde
 
-
 #define BD71828_REG_INT_MAIN		0xdf
 #define BD71828_REG_INT_BUCK		0xe0
 #define BD71828_REG_INT_DCIN1		0xe1
diff --git a/include/linux/mfd/rohm-shared.h b/include/linux/mfd/rohm-shared.h
new file mode 100644
index 000000000000..f16fc3b5000e
--- /dev/null
+++ b/include/linux/mfd/rohm-shared.h
@@ -0,0 +1,27 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/* Copyright (C) 2018 ROHM Semiconductors */
+
+
+#ifndef __LINUX_MFD_ROHM_SHARED_H__
+#define __LINUX_MFD_ROHM_SHARED_H__
+
+/*
+ * RTC definitions shared between
+ *
+ * BD70528
+ * and BD71828
+ */
+
+
+#define BD70528_MASK_RTC_SEC		0x7f
+#define BD70528_MASK_RTC_MINUTE	0x7f
+#define BD70528_MASK_RTC_HOUR_24H	0x80
+#define BD70528_MASK_RTC_HOUR_PM	0x20
+#define BD70528_MASK_RTC_HOUR		0x3f
+#define BD70528_MASK_RTC_DAY		0x3f
+#define BD70528_MASK_RTC_WEEK		0x07
+#define BD70528_MASK_RTC_MONTH		0x1f
+#define BD70528_MASK_RTC_YEAR		0xff
+#define BD70528_MASK_ALM_EN		0x7
+
+#endif /* __LINUX_MFD_ROHM_SHARED_H__ */
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply related	[flat|nested] 19+ messages in thread

* [PATCH v4 14/16] gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs
  2019-11-16 18:55 [PATCH v4 00/16] Support ROHM BD71828 PMIC Matti Vaittinen
                   ` (12 preceding siblings ...)
  2019-11-16 19:01 ` [PATCH v4 13/16] rtc: bd70528 add BD71828 support Matti Vaittinen
@ 2019-11-16 19:01 ` Matti Vaittinen
  2019-11-16 19:02 ` [PATCH v4 15/16] leds: Add common LED binding parsing support to LED class/core Matti Vaittinen
  2019-11-16 19:02 ` [PATCH v4 16/16] led: bd71828: Support LED outputs on ROHM BD71828 PMIC Matti Vaittinen
  15 siblings, 0 replies; 19+ messages in thread
From: Matti Vaittinen @ 2019-11-16 19:01 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Lee Jones, Jacek Anaszewski, Pavel Machek, Dan Murphy,
	Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Mauro Carvalho Chehab, Jeff Kirsher, Wolfram Sang,
	Marek Szyprowski, Heiner Kallweit, Nicholas Mc Guire,
	Phil Edworthy, linux-leds, devicetree, linux-kernel, linux-doc,
	linux-clk, linux-gpio, linux-rtc

ROHM BD71828 PMIC contains 4 pins which can be configured by OTP
to be used for general purposes. First 3 can be used as outputs
and 4.th pin can be used as input. Allow them to be controlled
via GPIO framework.

The driver assumes all of the pins are configured as GPIOs and
trusts that the reserved pins in other OTP configurations are
excluded from control using "gpio-reserved-ranges" device tree
property (or left untouched by GPIO users).

Typical use for 4.th pin (input) is to use it as HALL sensor
input so that this pin state is toggled when HALL sensor detects
LID position change (from close to open or open to close). PMIC
HW implements some extra logic which allows PMIC to power-up the
system when this pin is toggled. Please see the data sheet for
details of GPIO options which can be selected by OTP settings.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
 drivers/gpio/Kconfig        |  12 +++
 drivers/gpio/Makefile       |   1 +
 drivers/gpio/gpio-bd71828.c | 159 ++++++++++++++++++++++++++++++++++++
 3 files changed, 172 insertions(+)
 create mode 100644 drivers/gpio/gpio-bd71828.c

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 38e096e6925f..b4089096f7f2 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -994,6 +994,18 @@ config GPIO_BD70528
 	  This driver can also be built as a module. If so, the module
 	  will be called gpio-bd70528.
 
+config GPIO_BD71828
+	tristate "ROHM BD71828 GPIO support"
+	depends on MFD_ROHM_BD71828
+	help
+	  Support for GPIOs on ROHM BD71828 PMIC. There are three GPIOs
+	  available on the ROHM PMIC in total. The GPIOs are limited to
+	  outputs only and pins must be configured to GPIO outputs by
+	  OTP. Enable this only if you want to use these pins as outputs.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called gpio-bd71828.
+
 config GPIO_BD9571MWV
 	tristate "ROHM BD9571 GPIO support"
 	depends on MFD_BD9571MWV
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index d2fd19c15bae..034b38996579 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -35,6 +35,7 @@ obj-$(CONFIG_GPIO_ASPEED)		+= gpio-aspeed.o
 obj-$(CONFIG_GPIO_ATH79)		+= gpio-ath79.o
 obj-$(CONFIG_GPIO_BCM_KONA)		+= gpio-bcm-kona.o
 obj-$(CONFIG_GPIO_BD70528)		+= gpio-bd70528.o
+obj-$(CONFIG_GPIO_BD71828)		+= gpio-bd71828.o
 obj-$(CONFIG_GPIO_BD9571MWV)		+= gpio-bd9571mwv.o
 obj-$(CONFIG_GPIO_BRCMSTB)		+= gpio-brcmstb.o
 obj-$(CONFIG_GPIO_BT8XX)		+= gpio-bt8xx.o
diff --git a/drivers/gpio/gpio-bd71828.c b/drivers/gpio/gpio-bd71828.c
new file mode 100644
index 000000000000..04aade9e0a4d
--- /dev/null
+++ b/drivers/gpio/gpio-bd71828.c
@@ -0,0 +1,159 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2018 ROHM Semiconductors
+
+#include <linux/gpio/driver.h>
+#include <linux/mfd/rohm-bd71828.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define GPIO_OUT_REG(off) (BD71828_REG_GPIO_CTRL1 + (off))
+#define HALL_GPIO_OFFSET 3
+
+/*
+ * These defines can be removed when
+ * "gpio: Add definition for GPIO direction"
+ * (9208b1e77d6e8e9776f34f46ef4079ecac9c3c25 in GPIO tree) gets merged,
+ */
+#ifndef GPIO_LINE_DIRECTION_IN
+	#define GPIO_LINE_DIRECTION_IN 1
+	#define GPIO_LINE_DIRECTION_OUT 0
+#endif
+
+struct bd71828_gpio {
+	struct rohm_regmap_dev chip;
+	struct gpio_chip gpio;
+};
+
+static void bd71828_gpio_set(struct gpio_chip *chip, unsigned int offset,
+			     int value)
+{
+	int ret;
+	struct bd71828_gpio *bdgpio = gpiochip_get_data(chip);
+	u8 val = (value) ? BD71828_GPIO_OUT_HI : BD71828_GPIO_OUT_LO;
+
+	/*
+	 * The HALL input pin can only be used as input. If this is the pin
+	 * we are dealing with - then we are done
+	 */
+	if (offset == HALL_GPIO_OFFSET)
+		return;
+
+	ret = regmap_update_bits(bdgpio->chip.regmap, GPIO_OUT_REG(offset),
+				 BD71828_GPIO_OUT_MASK, val);
+	if (ret)
+		dev_err(bdgpio->chip.dev, "Could not set gpio to %d\n", value);
+}
+
+static int bd71828_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+	int ret;
+	unsigned int val;
+	struct bd71828_gpio *bdgpio = gpiochip_get_data(chip);
+
+	if (offset == HALL_GPIO_OFFSET)
+		ret = regmap_read(bdgpio->chip.regmap, BD71828_REG_IO_STAT,
+				  &val);
+	else
+		ret = regmap_read(bdgpio->chip.regmap, GPIO_OUT_REG(offset),
+				  &val);
+	if (!ret)
+		ret = (val & BD71828_GPIO_OUT_MASK);
+
+	return ret;
+}
+
+static int bd71828_gpio_set_config(struct gpio_chip *chip, unsigned int offset,
+				   unsigned long config)
+{
+	struct bd71828_gpio *bdgpio = gpiochip_get_data(chip);
+
+	if (offset == HALL_GPIO_OFFSET)
+		return -ENOTSUPP;
+
+	switch (pinconf_to_config_param(config)) {
+	case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+		return regmap_update_bits(bdgpio->chip.regmap,
+					  GPIO_OUT_REG(offset),
+					  BD71828_GPIO_DRIVE_MASK,
+					  BD71828_GPIO_OPEN_DRAIN);
+	case PIN_CONFIG_DRIVE_PUSH_PULL:
+		return regmap_update_bits(bdgpio->chip.regmap,
+					  GPIO_OUT_REG(offset),
+					  BD71828_GPIO_DRIVE_MASK,
+					  BD71828_GPIO_PUSH_PULL);
+	default:
+		break;
+	}
+	return -ENOTSUPP;
+}
+
+static int bd71828_get_direction(struct gpio_chip *chip, unsigned int offset)
+{
+	/*
+	 * Pin usage is selected by OTP data. We can't read it runtime. Hence
+	 * we trust that if the pin is not excluded by "gpio-reserved-ranges"
+	 * the OTP configuration is set to OUT. (Other pins but HALL input pin
+	 * on BD71828 can't really be used for general purpose input - input
+	 * states are used for specific cases like regulator control or
+	 * PMIC_ON_REQ.
+	 */
+	if (offset == HALL_GPIO_OFFSET)
+		return GPIO_LINE_DIRECTION_IN;
+
+	return GPIO_LINE_DIRECTION_OUT;
+}
+
+static int bd71828_probe(struct platform_device *pdev)
+{
+	struct bd71828_gpio *bdgpio;
+	struct rohm_regmap_dev *bd71828;
+
+	bd71828 = dev_get_drvdata(pdev->dev.parent);
+	if (!bd71828) {
+		dev_err(&pdev->dev, "No MFD driver data\n");
+		return -EINVAL;
+	}
+
+	bdgpio = devm_kzalloc(&pdev->dev, sizeof(*bdgpio),
+			      GFP_KERNEL);
+	if (!bdgpio)
+		return -ENOMEM;
+
+	bdgpio->chip.dev = &pdev->dev;
+	bdgpio->gpio.parent = pdev->dev.parent;
+	bdgpio->gpio.label = "bd71828-gpio";
+	bdgpio->gpio.owner = THIS_MODULE;
+	bdgpio->gpio.get_direction = bd71828_get_direction;
+	bdgpio->gpio.set_config = bd71828_gpio_set_config;
+	bdgpio->gpio.can_sleep = true;
+	bdgpio->gpio.get = bd71828_gpio_get;
+	bdgpio->gpio.set = bd71828_gpio_set;
+	bdgpio->gpio.base = -1;
+
+	/*
+	 * See if we need some implementation to mark some PINs as
+	 * not controllable based on DT info or if core can handle
+	 * "gpio-reserved-ranges" and exclude them from control
+	 */
+	bdgpio->gpio.ngpio = 4;
+	bdgpio->gpio.of_node = pdev->dev.parent->of_node;
+	bdgpio->chip.regmap = bd71828->regmap;
+
+	return devm_gpiochip_add_data(&pdev->dev, &bdgpio->gpio,
+				     bdgpio);
+}
+
+static struct platform_driver bd71828_gpio = {
+	.driver = {
+		.name = "bd71828-gpio"
+	},
+	.probe = bd71828_probe,
+};
+
+module_platform_driver(bd71828_gpio);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("BD71828 voltage regulator driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:bd71828-gpio");
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply related	[flat|nested] 19+ messages in thread

* [PATCH v4 15/16] leds: Add common LED binding parsing support to LED class/core
  2019-11-16 18:55 [PATCH v4 00/16] Support ROHM BD71828 PMIC Matti Vaittinen
                   ` (13 preceding siblings ...)
  2019-11-16 19:01 ` [PATCH v4 14/16] gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs Matti Vaittinen
@ 2019-11-16 19:02 ` Matti Vaittinen
  2019-11-18  5:59   ` Dan Carpenter
  2019-11-16 19:02 ` [PATCH v4 16/16] led: bd71828: Support LED outputs on ROHM BD71828 PMIC Matti Vaittinen
  15 siblings, 1 reply; 19+ messages in thread
From: Matti Vaittinen @ 2019-11-16 19:02 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Lee Jones, Jacek Anaszewski, Pavel Machek, Dan Murphy,
	Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Mauro Carvalho Chehab, Jeff Kirsher, Wolfram Sang,
	Marek Szyprowski, Heiner Kallweit, Nicholas Mc Guire,
	Phil Edworthy, linux-leds, devicetree, linux-kernel, linux-doc,
	linux-clk, linux-gpio, linux-rtc

Qucik grep for 'for_each' or 'linux,default-trigger' or
'default-state' under drivers/leds can tell quite a lot. It seems
multiple LED controller drivers implement the very similar looping
through the child nodes in order to locate the LED nodes and read
and support the common LED dt bindings. Implementing this same
stuff for all LED controllers gets old pretty fast.

This commit adds support for locating the LED node (based on known
node names - or linux,led-compatible property) and handling of
few common LED properties.

linux,default-trigger,
default-state (with the exception of keep),

(in addition to already handled
function-enumerator,
function,
color
and label).

Regarding the node look-up: If no init_data is given, then no
node-lookup is done and cdev name is used as such.

If init_data is goven but no starting point for node lookup - then
(parent) device's own DT node is used. If no led-compatible is given,
then of_match is searched for. If neither led-compatible not of_match
is given then device's own node or passed starting point are used as
such.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
 drivers/leds/led-class.c |  88 ++++++++++++--
 drivers/leds/led-core.c  | 246 +++++++++++++++++++++++++++++++--------
 include/linux/leds.h     |  90 ++++++++++++--
 3 files changed, 360 insertions(+), 64 deletions(-)

diff --git a/drivers/leds/led-class.c b/drivers/leds/led-class.c
index 647b1263c579..98173b64a597 100644
--- a/drivers/leds/led-class.c
+++ b/drivers/leds/led-class.c
@@ -235,6 +235,29 @@ static int led_classdev_next_name(const char *init_name, char *name,
 	return i;
 }
 
+static void led_add_props(struct led_classdev *ld, struct led_properties *props)
+{
+	if (props->default_trigger)
+		ld->default_trigger = props->default_trigger;
+	/*
+	 * According to binding docs the LED is by-default turned OFF unless
+	 * default_state is used to indicate it should be ON or that state
+	 * should be kept as is
+	 */
+	if (props->default_state) {
+		ld->brightness = LED_OFF;
+		if (!strcmp(props->default_state, "on"))
+			ld->brightness = LED_FULL;
+	/*
+	 * We probably should not call the brightness_get prior calling
+	 * the of_parse_cb if one is provided.
+	 * Add a flag to advertice that state should be queried and kept as-is.
+	 */
+		else if (!strcmp(props->default_state, "keep"))
+			props->brightness_keep = true;
+	}
+}
+
 /**
  * led_classdev_register_ext - register a new object of led_classdev class
  *			       with init data.
@@ -251,22 +274,58 @@ int led_classdev_register_ext(struct device *parent,
 	char final_name[LED_MAX_NAME_SIZE];
 	const char *proposed_name = composed_name;
 	int ret;
-
+	struct led_properties props = {0};
+	struct fwnode_handle *fw;
+
+	/*
+	 * We don't try getting the name based on DT node if init-data is not
+	 * given. We could see if we find LED properties from the device's node
+	 * but that might change LED names for old users of
+	 * led_classdev_register who have been providing the LED name in
+	 * cdev->name. So we seek fwnode for names only if init_data is given
+	 */
 	if (init_data) {
+		led_cdev->init_data = init_data;
 		if (init_data->devname_mandatory && !init_data->devicename) {
 			dev_err(parent, "Mandatory device name is missing");
 			return -EINVAL;
 		}
-		ret = led_compose_name(parent, init_data, composed_name);
+
+		fw = led_find_fwnode(parent, init_data);
+		if (!fw) {
+			dev_err(parent, "No fwnode found\n");
+			return -ENOENT;
+		}
+		/*
+		 * We did increase refcount for fwnode. Let's set a flag so we
+		 * can decrease it during deregistration
+		 */
+		led_cdev->fwnode_owned = true;
+
+		ret = led_parse_fwnode_props(parent, fw, &props);
+		if (ret)
+			goto err_out;
+
+		if (init_data->of_parse_cb)
+			ret = init_data->of_parse_cb(led_cdev, fw, &props);
 		if (ret < 0)
-			return ret;
+			goto err_out;
+
+		led_add_props(led_cdev, &props);
+
+		ret = led_compose_name(parent, init_data, &props,
+				       composed_name);
+		if (ret < 0)
+			goto err_out;
 	} else {
 		proposed_name = led_cdev->name;
+		led_cdev->fwnode_owned = false;
+		fw = NULL;
 	}
 
 	ret = led_classdev_next_name(proposed_name, final_name, sizeof(final_name));
 	if (ret < 0)
-		return ret;
+		goto err_out;
 
 	mutex_init(&led_cdev->led_access);
 	mutex_lock(&led_cdev->led_access);
@@ -274,22 +333,28 @@ int led_classdev_register_ext(struct device *parent,
 				led_cdev, led_cdev->groups, "%s", final_name);
 	if (IS_ERR(led_cdev->dev)) {
 		mutex_unlock(&led_cdev->led_access);
-		return PTR_ERR(led_cdev->dev);
+		ret = PTR_ERR(led_cdev->dev);
+		goto err_out;
 	}
-	if (init_data && init_data->fwnode)
-		led_cdev->dev->fwnode = init_data->fwnode;
+	if (fw)
+		led_cdev->dev->fwnode = fw;
 
 	if (ret)
 		dev_warn(parent, "Led %s renamed to %s due to name collision",
 				led_cdev->name, dev_name(led_cdev->dev));
 
+	if (props.brightness_keep)
+		if (led_cdev->brightness_get)
+			led_cdev->brightness =
+				 led_cdev->brightness_get(led_cdev);
+
 	if (led_cdev->flags & LED_BRIGHT_HW_CHANGED) {
 		ret = led_add_brightness_hw_changed(led_cdev);
 		if (ret) {
 			device_unregister(led_cdev->dev);
 			led_cdev->dev = NULL;
 			mutex_unlock(&led_cdev->led_access);
-			return ret;
+			goto err_out;
 		}
 	}
 
@@ -322,6 +387,10 @@ int led_classdev_register_ext(struct device *parent,
 			led_cdev->name);
 
 	return 0;
+err_out:
+	if (led_cdev->fwnode_owned)
+		fwnode_handle_put(fw);
+	return ret;
 }
 EXPORT_SYMBOL_GPL(led_classdev_register_ext);
 
@@ -355,6 +424,9 @@ void led_classdev_unregister(struct led_classdev *led_cdev)
 	if (led_cdev->flags & LED_BRIGHT_HW_CHANGED)
 		led_remove_brightness_hw_changed(led_cdev);
 
+	if (led_cdev->fwnode_owned)
+		fwnode_handle_put(led_cdev->dev->fwnode);
+
 	device_unregister(led_cdev->dev);
 
 	down_write(&leds_list_lock);
diff --git a/drivers/leds/led-core.c b/drivers/leds/led-core.c
index f1f718dbe0f8..0cd105a5f200 100644
--- a/drivers/leds/led-core.c
+++ b/drivers/leds/led-core.c
@@ -365,70 +365,216 @@ void led_sysfs_enable(struct led_classdev *led_cdev)
 }
 EXPORT_SYMBOL_GPL(led_sysfs_enable);
 
-static void led_parse_fwnode_props(struct device *dev,
-				   struct fwnode_handle *fwnode,
-				   struct led_properties *props)
+static int fw_is_match(struct fwnode_handle *fw,
+		       struct led_fw_match_property *mp, void *val)
 {
+	void *cmp = mp->raw_val;
 	int ret;
 
+	if (mp->raw_val) {
+		ret = fwnode_property_read_u8_array(fw, mp->name, val,
+						    mp->size);
+	} else if (mp->intval) {
+		cmp = mp->intval;
+		switch (mp->size) {
+		case 1:
+			ret = fwnode_property_read_u8_array(fw, mp->name, val,
+						    mp->size);
+			break;
+		case 2:
+			ret = fwnode_property_read_u16_array(fw, mp->name, val,
+						    mp->size);
+			break;
+		case 4:
+			ret = fwnode_property_read_u32_array(fw, mp->name, val,
+						    mp->size);
+			break;
+		case 8:
+			ret = fwnode_property_read_u64_array(fw, mp->name, val,
+						    mp->size);
+			break;
+		default:
+			return -EINVAL;
+		}
+	}
+	if (!ret && cmp) {
+		if (!memcmp(val, cmp, mp->size)) {
+			kfree(val);
+			return 1;
+		}
+	}
+	return 0;
+}
+/**
+ * led_find_fwnode - find fwnode for led
+ * @parent	LED controller device
+ * @init_data	led init data with match information
+ *
+ * Scans the firmware nodes and returns node matching the given init_data.
+ * NOTE: Function increases refcount for found node. Caller must decrease
+ * refcount using fwnode_handle_put when finished with node.
+ */
+struct fwnode_handle *led_find_fwnode(struct device *parent,
+				      struct led_init_data *init_data)
+{
+	struct fwnode_handle *fw;
+
+	/*
+	 * This should never be called W/O init data. We could always return
+	 * dev_fwnode() - but then we should pump-up the refcount
+	 */
+	if (!init_data)
+		return NULL;
+
+	if (!init_data->fwnode)
+		fw = dev_fwnode(parent);
+	else
+		fw = init_data->fwnode;
+
+	if (!fw)
+		return NULL;
+
+	/*
+	 * Simple things are pretty. I think simplest is to use DT node-name
+	 * for matching the node with LED - same way regulators use the node
+	 * name to match with desc.
+	 *
+	 * This may not work with existing LED DT entries if the node name has
+	 * been freely selectible. In order to this to work the binding doc
+	 * for LED driver should define usable node names.
+	 *
+	 * If this is not working we can define specific match property which
+	 * value we scan and use for matching for LEDs connected to the
+	 * controller.
+	 */
+	if (init_data->match_property.name && init_data->match_property.size) {
+		u8 *val;
+		int ret;
+		struct fwnode_handle *child;
+		struct led_fw_match_property *mp;
+
+		mp = &init_data->match_property;
+
+		val = kzalloc(mp->size, GFP_KERNEL);
+		if (!val)
+			return ERR_PTR(-ENOMEM);
+
+		fwnode_for_each_child_node(fw, child) {
+			ret = fw_is_match(child, mp, val);
+			if (ret > 0) {
+				kfree(val);
+				return child;
+			}
+			if (ret < 0) {
+				dev_err(parent,
+					"invalid fw match. Use raw_val?\n");
+				fwnode_handle_put(child);
+				break;
+			}
+		}
+		kfree(val);
+	}
+	if (init_data->of_match)
+		fw = fwnode_get_named_child_node(fw, init_data->of_match);
+	else
+		fw = fwnode_handle_get(fw);
+
+	return fw;
+}
+EXPORT_SYMBOL(led_find_fwnode);
+
+int led_parse_fwnode_props(struct device *dev, struct fwnode_handle *fwnode,
+			   struct led_properties *props)
+{
+	int ret = 0;
+
 	if (!fwnode)
-		return;
+		return 0;
 
 	if (fwnode_property_present(fwnode, "label")) {
 		ret = fwnode_property_read_string(fwnode, "label", &props->label);
 		if (ret)
 			dev_err(dev, "Error parsing 'label' property (%d)\n", ret);
-		return;
+		return ret;
 	}
 
+	/**
+	 * Please note, logic changed - if invalid property is found we bail
+	 * early out without parsing the rest of the properties. Originally
+	 * this was the case only for 'label' property. I don't know the
+	 * rationale behind original logic allowing invalid properties to be
+	 * given. If there is a reason then we should reconsider this.
+	 * Intuitively it feels correct to just yell and quit if we hit value we
+	 * don't understand - but intuition may be wrong at times :)
+	 */
 	if (fwnode_property_present(fwnode, "color")) {
 		ret = fwnode_property_read_u32(fwnode, "color", &props->color);
-		if (ret)
+		if (ret) {
 			dev_err(dev, "Error parsing 'color' property (%d)\n", ret);
-		else if (props->color >= LED_COLOR_ID_MAX)
+			return ret;
+		} else if (props->color >= LED_COLOR_ID_MAX) {
 			dev_err(dev, "LED color identifier out of range\n");
-		else
-			props->color_present = true;
+			return ret;
+		}
+		props->color_present = true;
 	}
 
+	if (fwnode_property_present(fwnode, "function")) {
+		ret = fwnode_property_read_string(fwnode, "function",
+						  &props->function);
+		if (ret) {
+			dev_err(dev,
+				"Error parsing 'function' property (%d)\n",
+				ret);
+			return ret;
+		}
+	}
 
-	if (!fwnode_property_present(fwnode, "function"))
-		return;
-
-	ret = fwnode_property_read_string(fwnode, "function", &props->function);
-	if (ret) {
-		dev_err(dev,
-			"Error parsing 'function' property (%d)\n",
-			ret);
+	if (fwnode_property_present(fwnode, "function-enumerator")) {
+		ret = fwnode_property_read_u32(fwnode, "function-enumerator",
+					       &props->func_enum);
+		if (ret) {
+			dev_err(dev,
+				"Error parsing 'function-enumerator' property (%d)\n",
+				ret);
+			return ret;
+		}
+		props->func_enum_present = true;
 	}
 
-	if (!fwnode_property_present(fwnode, "function-enumerator"))
-		return;
+	if (fwnode_property_present(fwnode, "default-state")) {
+		ret = fwnode_property_read_string(fwnode, "default-state",
+						  &props->default_state);
+		if (ret) {
+			dev_err(dev,
+				"Error parsing 'default-state' property (%d)\n",
+				ret);
+			return ret;
+		}
+	}
 
-	ret = fwnode_property_read_u32(fwnode, "function-enumerator",
-				       &props->func_enum);
-	if (ret) {
-		dev_err(dev,
-			"Error parsing 'function-enumerator' property (%d)\n",
-			ret);
-	} else {
-		props->func_enum_present = true;
+	if (fwnode_property_present(fwnode, "linux,default-trigger")) {
+		ret = fwnode_property_read_string(fwnode,
+						  "linux,default-trigger",
+						  &props->default_trigger);
+		if (ret)
+			dev_err(dev,
+				"Error parsing 'linux,default-trigger' property (%d)\n",
+				ret);
 	}
+	return ret;
 }
+EXPORT_SYMBOL_GPL(led_parse_fwnode_props);
 
 int led_compose_name(struct device *dev, struct led_init_data *init_data,
-		     char *led_classdev_name)
+		     struct led_properties *props, char *led_classdev_name)
 {
-	struct led_properties props = {};
-	struct fwnode_handle *fwnode = init_data->fwnode;
 	const char *devicename = init_data->devicename;
 
 	if (!led_classdev_name)
 		return -EINVAL;
 
-	led_parse_fwnode_props(dev, fwnode, &props);
-
-	if (props.label) {
+	if (props->label) {
 		/*
 		 * If init_data.devicename is NULL, then it indicates that
 		 * DT label should be used as-is for LED class device name.
@@ -436,23 +582,23 @@ int led_compose_name(struct device *dev, struct led_init_data *init_data,
 		 * the final LED class device name.
 		 */
 		if (!devicename) {
-			strscpy(led_classdev_name, props.label,
+			strscpy(led_classdev_name, props->label,
 				LED_MAX_NAME_SIZE);
 		} else {
 			snprintf(led_classdev_name, LED_MAX_NAME_SIZE, "%s:%s",
-				 devicename, props.label);
+				 devicename, props->label);
 		}
-	} else if (props.function || props.color_present) {
+	} else if (props->function || props->color_present) {
 		char tmp_buf[LED_MAX_NAME_SIZE];
 
-		if (props.func_enum_present) {
+		if (props->func_enum_present) {
 			snprintf(tmp_buf, LED_MAX_NAME_SIZE, "%s:%s-%d",
-				 props.color_present ? led_colors[props.color] : "",
-				 props.function ?: "", props.func_enum);
+				 props->color_present ? led_colors[props->color] : "",
+				 props->function ?: "", props->func_enum);
 		} else {
 			snprintf(tmp_buf, LED_MAX_NAME_SIZE, "%s:%s",
-				 props.color_present ? led_colors[props.color] : "",
-				 props.function ?: "");
+				 props->color_present ? led_colors[props->color] : "",
+				 props->function ?: "");
 		}
 		if (init_data->devname_mandatory) {
 			snprintf(led_classdev_name, LED_MAX_NAME_SIZE, "%s:%s",
@@ -468,11 +614,19 @@ int led_compose_name(struct device *dev, struct led_init_data *init_data,
 		}
 		snprintf(led_classdev_name, LED_MAX_NAME_SIZE, "%s:%s",
 			 devicename, init_data->default_label);
-	} else if (is_of_node(fwnode)) {
-		strscpy(led_classdev_name, to_of_node(fwnode)->name,
-			LED_MAX_NAME_SIZE);
-	} else
-		return -EINVAL;
+	} else {
+		struct fwnode_handle *fwnode = led_find_fwnode(dev, init_data);
+		int ret = -EINVAL;
+
+		if (is_of_node(fwnode)) {
+			ret = 0;
+			strscpy(led_classdev_name, to_of_node(fwnode)->name,
+				LED_MAX_NAME_SIZE);
+		}
+		fwnode_handle_put(fwnode);
+
+		return ret;
+	}
 
 	return 0;
 }
diff --git a/include/linux/leds.h b/include/linux/leds.h
index efb309dba914..aea7d6bc7294 100644
--- a/include/linux/leds.h
+++ b/include/linux/leds.h
@@ -13,6 +13,7 @@
 #include <linux/kernfs.h>
 #include <linux/list.h>
 #include <linux/mutex.h>
+#include <linux/property.h>
 #include <linux/rwsem.h>
 #include <linux/spinlock.h>
 #include <linux/timer.h>
@@ -20,6 +21,7 @@
 
 struct device;
 struct led_pattern;
+struct led_classdev;
 /*
  * LED Core
  */
@@ -31,8 +33,47 @@ enum led_brightness {
 	LED_FULL	= 255,
 };
 
+struct led_properties {
+	u32		color;
+	bool		color_present;
+	const char	*function;
+	u32		func_enum;
+	bool		func_enum_present;
+	const char	*label;
+	const char	*default_trigger;
+	const char	*default_state;
+	bool		brightness_keep;
+};
+
+struct led_fw_match_property {
+	const char *name;	/* Name of the property to match */
+	void *raw_val;		/* Raw property value as present in fwnode */
+	void *intval;		/* Property value if 8,16,32 or 64bit integer */
+	size_t size;		/* Size of value in bytes */
+};
+
 struct led_init_data {
-	/* device fwnode handle */
+	/*
+	 * If DT binding dictates the node name the driver can fill of_match
+	 * corresponding to node name describing this LED. If fwnode is given
+	 * the match is searched from it's child nodes. If not, the match is
+	 * searched from device's own child nodes.
+	 */
+	const char *of_match;
+	/*
+	 * If fwnode contains property with known value the driver can specify
+	 * correct propertty-value pair here to do the matching. This has higher
+	 * priority than of_match. If fwnode is given the match is searched
+	 * from it's child nodes. If not match is searched from device's
+	 * own child nodes.
+	 */
+	struct led_fw_match_property match_property;
+	/*
+	 * device fwnode handle. If of_match or led_compatible are not given
+	 * this is used for LED as given. If of_match or led_compatible are
+	 * given then this is used as a parent node whose child nodes are
+	 * scanned for given match.
+	 */
 	struct fwnode_handle *fwnode;
 	/*
 	 * default <color:function> tuple, for backward compatibility
@@ -53,9 +94,17 @@ struct led_init_data {
 	 * set it to true
 	 */
 	bool devname_mandatory;
+	/*
+	 * Callback which a LED driver can register if it has own non-standard
+	 * DT properties. Core calls this with the located DT node during
+	 * class_device registration
+	 */
+	int (*of_parse_cb)(struct led_classdev *ld, struct fwnode_handle *fw,
+			    struct led_properties *props);
 };
 
 struct led_classdev {
+	struct led_init_data	*init_data;
 	const char		*name;
 	enum led_brightness	 brightness;
 	enum led_brightness	 max_brightness;
@@ -148,6 +197,7 @@ struct led_classdev {
 
 	/* Ensures consistent access to the LED Flash Class device */
 	struct mutex		led_access;
+	bool			fwnode_owned;
 };
 
 /**
@@ -302,6 +352,7 @@ extern void led_sysfs_enable(struct led_classdev *led_cdev);
  * led_compose_name - compose LED class device name
  * @dev: LED controller device object
  * @init_data: the LED class device initialization data
+ * @props: LED properties as parsed from fwnode.
  * @led_classdev_name: composed LED class device name
  *
  * Create LED class device name basing on the provided init_data argument.
@@ -311,6 +362,7 @@ extern void led_sysfs_enable(struct led_classdev *led_cdev);
  * Returns: 0 on success or negative error value on failure
  */
 extern int led_compose_name(struct device *dev, struct led_init_data *init_data,
+			    struct led_properties *props,
 			    char *led_classdev_name);
 
 /**
@@ -324,6 +376,33 @@ static inline bool led_sysfs_is_disabled(struct led_classdev *led_cdev)
 	return led_cdev->flags & LED_SYSFS_DISABLE;
 }
 
+/**
+ * led_find_fwnode - find fwnode matching given LED init data
+ * @parent: LED controller device this LED is driven by
+ * @init_data: the LED class device initialization data
+ *
+ * Find the fw node matching given LED init data.
+ * NOTE: Function increases refcount for found node. Caller must decrease
+ * refcount using fwnode_handle_put when finished with node.
+ *
+ * Returns: node handle or NULL if matching fw node was not found
+ */
+struct fwnode_handle *led_find_fwnode(struct device *parent,
+				      struct led_init_data *init_data);
+
+/**
+ * led_parse_fwnode_props - parse LED common properties from fwnode
+ * @dev: pointer to LED device.
+ * @fwnode: LED node containing the properties
+ * @props: structure where found property data is stored.
+ *
+ * Parse the common LED properties from fwnode.
+ *
+ * Returns: 0 on success or negative error value on failure
+ */
+int led_parse_fwnode_props(struct device *dev, struct fwnode_handle *fwnode,
+			   struct led_properties *props);
+
 /*
  * LED Triggers
  */
@@ -490,15 +569,6 @@ struct led_platform_data {
 	struct led_info	*leds;
 };
 
-struct led_properties {
-	u32		color;
-	bool		color_present;
-	const char	*function;
-	u32		func_enum;
-	bool		func_enum_present;
-	const char	*label;
-};
-
 struct gpio_desc;
 typedef int (*gpio_blink_set_t)(struct gpio_desc *desc, int state,
 				unsigned long *delay_on,
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply related	[flat|nested] 19+ messages in thread

* [PATCH v4 16/16] led: bd71828: Support LED outputs on ROHM BD71828 PMIC
  2019-11-16 18:55 [PATCH v4 00/16] Support ROHM BD71828 PMIC Matti Vaittinen
                   ` (14 preceding siblings ...)
  2019-11-16 19:02 ` [PATCH v4 15/16] leds: Add common LED binding parsing support to LED class/core Matti Vaittinen
@ 2019-11-16 19:02 ` Matti Vaittinen
  15 siblings, 0 replies; 19+ messages in thread
From: Matti Vaittinen @ 2019-11-16 19:02 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Lee Jones, Jacek Anaszewski, Pavel Machek, Dan Murphy,
	Rob Herring, Mark Rutland, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Mauro Carvalho Chehab, Jeff Kirsher, Wolfram Sang,
	Marek Szyprowski, Heiner Kallweit, Nicholas Mc Guire,
	Phil Edworthy, linux-leds, devicetree, linux-kernel, linux-doc,
	linux-clk, linux-gpio, linux-rtc

ROHM BD71828 power management IC has two LED outputs for charge status
and button pressing indications. The LED outputs can also be forced
by SW so add driver allowing to use these LEDs for other indications
as well.

Leds are controlled by SW using 'Force ON' bits. Please note the
constrains mentioned in data-sheet:
    1. If one LED is forced ON - then also the other LED is forced.
            => You can't use SW control to force ON one LED and allow HW
               to control the other.
    2. You can't force both LEDs OFF. If the FORCE bit for both LED's is
       zero, then LEDs are controlled by HW and indicate button/charger
       states as explained in data-sheet.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
 drivers/leds/Kconfig        |  10 ++++
 drivers/leds/Makefile       |   1 +
 drivers/leds/leds-bd71828.c | 104 ++++++++++++++++++++++++++++++++++++
 3 files changed, 115 insertions(+)
 create mode 100644 drivers/leds/leds-bd71828.c

diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index 1988de1d64c0..cafcbae7c084 100644
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -532,6 +532,16 @@ config LEDS_BD2802
 	  This option enables support for BD2802GU RGB LED driver chips
 	  accessed via the I2C bus.
 
+config LEDS_BD71828
+	tristate "LED driver for LEDS on ROHM BD71828 PMIC"
+	depends on LEDS_CLASS
+	depends on MFD_ROHM_BD71828
+	help
+	  This option enables support for LED outputs located on ROHM
+	  BD71828 power management IC. ROHM BD71828 has two led output pins
+	  which can be left to indicate HW states or controlled by SW. Say
+	  yes here if you want to enable SW control for these LEDs.
+
 config LEDS_INTEL_SS4200
 	tristate "LED driver for Intel NAS SS4200 series"
 	depends on LEDS_CLASS
diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
index 41fb073a39c1..2a8f6a8e4c7c 100644
--- a/drivers/leds/Makefile
+++ b/drivers/leds/Makefile
@@ -15,6 +15,7 @@ obj-$(CONFIG_LEDS_AN30259A)		+= leds-an30259a.o
 obj-$(CONFIG_LEDS_BCM6328)		+= leds-bcm6328.o
 obj-$(CONFIG_LEDS_BCM6358)		+= leds-bcm6358.o
 obj-$(CONFIG_LEDS_BD2802)		+= leds-bd2802.o
+obj-$(CONFIG_LEDS_BD71828)		+= leds-bd71828.o
 obj-$(CONFIG_LEDS_CPCAP)		+= leds-cpcap.o
 obj-$(CONFIG_LEDS_LOCOMO)		+= leds-locomo.o
 obj-$(CONFIG_LEDS_LM3530)		+= leds-lm3530.o
diff --git a/drivers/leds/leds-bd71828.c b/drivers/leds/leds-bd71828.c
new file mode 100644
index 000000000000..f032e24485e9
--- /dev/null
+++ b/drivers/leds/leds-bd71828.c
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2019 ROHM Semiconductors
+
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/leds.h>
+#include <linux/mfd/rohm-bd71828.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+#define BD71828_LED_TO_DATA(l) ((l)->id == ID_GREEN_LED ? \
+	container_of((l), struct bd71828_leds, green) : \
+	container_of((l), struct bd71828_leds, amber))
+
+/* Names for led identification - these match the data sheet names */
+enum {
+	ID_GREEN_LED,
+	ID_AMBER_LED,
+	ID_NMBR_OF,
+};
+
+struct bd71828_led {
+	struct led_init_data init_data;
+	int id;
+	struct led_classdev l;
+	u8 force_mask;
+};
+
+struct bd71828_leds {
+	struct rohm_regmap_dev *bd71828;
+	struct bd71828_led green;
+	struct bd71828_led amber;
+};
+
+static int bd71828_led_brightness_set(struct led_classdev *led_cdev,
+				      enum led_brightness value)
+{
+	struct bd71828_led *l = container_of(led_cdev, struct bd71828_led, l);
+	struct bd71828_leds *data;
+	unsigned int val = BD71828_LED_OFF;
+
+	data = BD71828_LED_TO_DATA(l);
+	if (value != LED_OFF)
+		val = BD71828_LED_ON;
+
+	return regmap_update_bits(data->bd71828->regmap, BD71828_REG_LED_CTRL,
+			    l->force_mask, val);
+}
+
+static int bd71828_led_probe(struct platform_device *pdev)
+{
+	struct rohm_regmap_dev *bd71828;
+	struct bd71828_leds *l;
+	struct bd71828_led *g, *a;
+	int ret;
+
+	bd71828 = dev_get_drvdata(pdev->dev.parent);
+	l = devm_kzalloc(&pdev->dev, sizeof(*l), GFP_KERNEL);
+	if (!l)
+		return -ENOMEM;
+	l->bd71828 = bd71828;
+	a = &l->amber;
+	g = &l->green;
+
+	/* Fill in details for 'AMBLED' */
+	a->init_data.match_property.name = "rohm,led-compatible";
+	a->init_data.match_property.raw_val = "bd71828-ambled";
+	a->init_data.match_property.size = strlen("bd71828-ambled");
+	a->id = ID_AMBER_LED;
+	a->force_mask = BD71828_MASK_LED_AMBER;
+
+	/* Fill in details for 'GRNLED' */
+	g->init_data.match_property.name = "rohm,led-compatible";
+	g->init_data.match_property.raw_val = "bd71828-grnled";
+	g->init_data.match_property.size = strlen("bd71828-grnled");
+	g->id = ID_GREEN_LED;
+	g->force_mask = BD71828_MASK_LED_GREEN;
+
+	a->l.brightness_set_blocking = bd71828_led_brightness_set;
+	g->l.brightness_set_blocking = bd71828_led_brightness_set;
+
+	ret = devm_led_classdev_register_ext(&pdev->dev, &g->l, &g->init_data);
+	if (ret)
+		return ret;
+
+	return devm_led_classdev_register_ext(&pdev->dev, &a->l, &a->init_data);
+}
+
+static struct platform_driver bd71828_led_driver = {
+	.driver = {
+		.name  = "bd71828-led",
+	},
+	.probe  = bd71828_led_probe,
+};
+
+module_platform_driver(bd71828_led_driver);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("ROHM BD71828 LED driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:bd71828-led");
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply related	[flat|nested] 19+ messages in thread

* Re: [PATCH v4 15/16] leds: Add common LED binding parsing support to LED class/core
  2019-11-16 19:02 ` [PATCH v4 15/16] leds: Add common LED binding parsing support to LED class/core Matti Vaittinen
@ 2019-11-18  5:59   ` Dan Carpenter
  2019-11-18  6:34     ` Vaittinen, Matti
  0 siblings, 1 reply; 19+ messages in thread
From: Dan Carpenter @ 2019-11-18  5:59 UTC (permalink / raw)
  To: kbuild, Matti Vaittinen
  Cc: kbuild-all, matti.vaittinen, mazziesaccount, Lee Jones,
	Jacek Anaszewski, Pavel Machek, Dan Murphy, Rob Herring,
	Mark Rutland, Liam Girdwood, Mark Brown, Jonathan Corbet,
	Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Mauro Carvalho Chehab, Jeff Kirsher, Wolfram Sang,
	Marek Szyprowski, Heiner Kallweit, Nicholas Mc Guire,
	Phil Edworthy, linux-leds, devicetree, linux-kernel, linux-doc,
	linux-clk, linux-gpio, linux-rtc

Hi Matti,

[auto build test WARNING on 31f4f5b495a62c9a8b15b1c3581acd5efeb9af8c]

url:    https://github.com/0day-ci/linux/commits/Matti-Vaittinen/Support-ROHM-BD71828-PMIC/20191117-030515
base:    31f4f5b495a62c9a8b15b1c3581acd5efeb9af8c

If you fix the issue, kindly add following tag
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>

smatch warnings:
drivers/leds/led-core.c:400 fw_is_match() error: uninitialized symbol 'ret'.
drivers/leds/led-core.c:465 led_find_fwnode() error: double free of 'val'

# https://github.com/0day-ci/linux/commit/7b8033cfca34525c9e45fe2e74783fef74f4a49c
git remote add linux-review https://github.com/0day-ci/linux
git remote update linux-review
git checkout 7b8033cfca34525c9e45fe2e74783fef74f4a49c
vim +/ret +400 drivers/leds/led-core.c

7b8033cfca3452 Matti Vaittinen  2019-11-16  368  static int fw_is_match(struct fwnode_handle *fw,
7b8033cfca3452 Matti Vaittinen  2019-11-16  369  		       struct led_fw_match_property *mp, void *val)
bb4e9af0348dfe Jacek Anaszewski 2019-06-09  370  {
7b8033cfca3452 Matti Vaittinen  2019-11-16  371  	void *cmp = mp->raw_val;
bb4e9af0348dfe Jacek Anaszewski 2019-06-09  372  	int ret;
bb4e9af0348dfe Jacek Anaszewski 2019-06-09  373  
7b8033cfca3452 Matti Vaittinen  2019-11-16  374  	if (mp->raw_val) {
7b8033cfca3452 Matti Vaittinen  2019-11-16  375  		ret = fwnode_property_read_u8_array(fw, mp->name, val,
7b8033cfca3452 Matti Vaittinen  2019-11-16  376  						    mp->size);
7b8033cfca3452 Matti Vaittinen  2019-11-16  377  	} else if (mp->intval) {
                                                                   ^^^^^^^^^^
Smatch is complaining about if this is false then ret isn't set.

7b8033cfca3452 Matti Vaittinen  2019-11-16  378  		cmp = mp->intval;
7b8033cfca3452 Matti Vaittinen  2019-11-16  379  		switch (mp->size) {
7b8033cfca3452 Matti Vaittinen  2019-11-16  380  		case 1:
7b8033cfca3452 Matti Vaittinen  2019-11-16  381  			ret = fwnode_property_read_u8_array(fw, mp->name, val,
7b8033cfca3452 Matti Vaittinen  2019-11-16  382  						    mp->size);
7b8033cfca3452 Matti Vaittinen  2019-11-16  383  			break;
7b8033cfca3452 Matti Vaittinen  2019-11-16  384  		case 2:
7b8033cfca3452 Matti Vaittinen  2019-11-16  385  			ret = fwnode_property_read_u16_array(fw, mp->name, val,
7b8033cfca3452 Matti Vaittinen  2019-11-16  386  						    mp->size);
7b8033cfca3452 Matti Vaittinen  2019-11-16  387  			break;
7b8033cfca3452 Matti Vaittinen  2019-11-16  388  		case 4:
7b8033cfca3452 Matti Vaittinen  2019-11-16  389  			ret = fwnode_property_read_u32_array(fw, mp->name, val,
7b8033cfca3452 Matti Vaittinen  2019-11-16  390  						    mp->size);
7b8033cfca3452 Matti Vaittinen  2019-11-16  391  			break;
7b8033cfca3452 Matti Vaittinen  2019-11-16  392  		case 8:
7b8033cfca3452 Matti Vaittinen  2019-11-16  393  			ret = fwnode_property_read_u64_array(fw, mp->name, val,
7b8033cfca3452 Matti Vaittinen  2019-11-16  394  						    mp->size);
7b8033cfca3452 Matti Vaittinen  2019-11-16  395  			break;
7b8033cfca3452 Matti Vaittinen  2019-11-16  396  		default:
7b8033cfca3452 Matti Vaittinen  2019-11-16  397  			return -EINVAL;
7b8033cfca3452 Matti Vaittinen  2019-11-16  398  		}
7b8033cfca3452 Matti Vaittinen  2019-11-16  399  	}
7b8033cfca3452 Matti Vaittinen  2019-11-16 @400  	if (!ret && cmp) {
7b8033cfca3452 Matti Vaittinen  2019-11-16  401  		if (!memcmp(val, cmp, mp->size)) {
7b8033cfca3452 Matti Vaittinen  2019-11-16  402  			kfree(val);
                                                                        ^^^^^^^^^^
This kfree leads to a double free below.  Freeing it here is a
layering violation, so delete this one and keep the kfree in the caller.

7b8033cfca3452 Matti Vaittinen  2019-11-16  403  			return 1;
7b8033cfca3452 Matti Vaittinen  2019-11-16  404  		}
7b8033cfca3452 Matti Vaittinen  2019-11-16  405  	}
7b8033cfca3452 Matti Vaittinen  2019-11-16  406  	return 0;
7b8033cfca3452 Matti Vaittinen  2019-11-16  407  }
7b8033cfca3452 Matti Vaittinen  2019-11-16  408  /**
7b8033cfca3452 Matti Vaittinen  2019-11-16  409   * led_find_fwnode - find fwnode for led
7b8033cfca3452 Matti Vaittinen  2019-11-16  410   * @parent	LED controller device
7b8033cfca3452 Matti Vaittinen  2019-11-16  411   * @init_data	led init data with match information
7b8033cfca3452 Matti Vaittinen  2019-11-16  412   *
7b8033cfca3452 Matti Vaittinen  2019-11-16  413   * Scans the firmware nodes and returns node matching the given init_data.
7b8033cfca3452 Matti Vaittinen  2019-11-16  414   * NOTE: Function increases refcount for found node. Caller must decrease
7b8033cfca3452 Matti Vaittinen  2019-11-16  415   * refcount using fwnode_handle_put when finished with node.
7b8033cfca3452 Matti Vaittinen  2019-11-16  416   */
7b8033cfca3452 Matti Vaittinen  2019-11-16  417  struct fwnode_handle *led_find_fwnode(struct device *parent,
7b8033cfca3452 Matti Vaittinen  2019-11-16  418  				      struct led_init_data *init_data)
7b8033cfca3452 Matti Vaittinen  2019-11-16  419  {
7b8033cfca3452 Matti Vaittinen  2019-11-16  420  	struct fwnode_handle *fw;
7b8033cfca3452 Matti Vaittinen  2019-11-16  421  
7b8033cfca3452 Matti Vaittinen  2019-11-16  422  	/*
7b8033cfca3452 Matti Vaittinen  2019-11-16  423  	 * This should never be called W/O init data. We could always return
7b8033cfca3452 Matti Vaittinen  2019-11-16  424  	 * dev_fwnode() - but then we should pump-up the refcount
7b8033cfca3452 Matti Vaittinen  2019-11-16  425  	 */
7b8033cfca3452 Matti Vaittinen  2019-11-16  426  	if (!init_data)
7b8033cfca3452 Matti Vaittinen  2019-11-16  427  		return NULL;
7b8033cfca3452 Matti Vaittinen  2019-11-16  428  
7b8033cfca3452 Matti Vaittinen  2019-11-16  429  	if (!init_data->fwnode)
7b8033cfca3452 Matti Vaittinen  2019-11-16  430  		fw = dev_fwnode(parent);
7b8033cfca3452 Matti Vaittinen  2019-11-16  431  	else
7b8033cfca3452 Matti Vaittinen  2019-11-16  432  		fw = init_data->fwnode;
7b8033cfca3452 Matti Vaittinen  2019-11-16  433  
7b8033cfca3452 Matti Vaittinen  2019-11-16  434  	if (!fw)
7b8033cfca3452 Matti Vaittinen  2019-11-16  435  		return NULL;
7b8033cfca3452 Matti Vaittinen  2019-11-16  436  
7b8033cfca3452 Matti Vaittinen  2019-11-16  437  	/*
7b8033cfca3452 Matti Vaittinen  2019-11-16  438  	 * Simple things are pretty. I think simplest is to use DT node-name
7b8033cfca3452 Matti Vaittinen  2019-11-16  439  	 * for matching the node with LED - same way regulators use the node
7b8033cfca3452 Matti Vaittinen  2019-11-16  440  	 * name to match with desc.
7b8033cfca3452 Matti Vaittinen  2019-11-16  441  	 *
7b8033cfca3452 Matti Vaittinen  2019-11-16  442  	 * This may not work with existing LED DT entries if the node name has
7b8033cfca3452 Matti Vaittinen  2019-11-16  443  	 * been freely selectible. In order to this to work the binding doc
7b8033cfca3452 Matti Vaittinen  2019-11-16  444  	 * for LED driver should define usable node names.
7b8033cfca3452 Matti Vaittinen  2019-11-16  445  	 *
7b8033cfca3452 Matti Vaittinen  2019-11-16  446  	 * If this is not working we can define specific match property which
7b8033cfca3452 Matti Vaittinen  2019-11-16  447  	 * value we scan and use for matching for LEDs connected to the
7b8033cfca3452 Matti Vaittinen  2019-11-16  448  	 * controller.
7b8033cfca3452 Matti Vaittinen  2019-11-16  449  	 */
7b8033cfca3452 Matti Vaittinen  2019-11-16  450  	if (init_data->match_property.name && init_data->match_property.size) {
7b8033cfca3452 Matti Vaittinen  2019-11-16  451  		u8 *val;
7b8033cfca3452 Matti Vaittinen  2019-11-16  452  		int ret;
7b8033cfca3452 Matti Vaittinen  2019-11-16  453  		struct fwnode_handle *child;
7b8033cfca3452 Matti Vaittinen  2019-11-16  454  		struct led_fw_match_property *mp;
7b8033cfca3452 Matti Vaittinen  2019-11-16  455  
7b8033cfca3452 Matti Vaittinen  2019-11-16  456  		mp = &init_data->match_property;
7b8033cfca3452 Matti Vaittinen  2019-11-16  457  
7b8033cfca3452 Matti Vaittinen  2019-11-16  458  		val = kzalloc(mp->size, GFP_KERNEL);
7b8033cfca3452 Matti Vaittinen  2019-11-16  459  		if (!val)
7b8033cfca3452 Matti Vaittinen  2019-11-16  460  			return ERR_PTR(-ENOMEM);
7b8033cfca3452 Matti Vaittinen  2019-11-16  461  
7b8033cfca3452 Matti Vaittinen  2019-11-16  462  		fwnode_for_each_child_node(fw, child) {
7b8033cfca3452 Matti Vaittinen  2019-11-16  463  			ret = fw_is_match(child, mp, val);
                                                                                                     ^^^

7b8033cfca3452 Matti Vaittinen  2019-11-16  464  			if (ret > 0) {
7b8033cfca3452 Matti Vaittinen  2019-11-16 @465  				kfree(val);
                                                                                      ^^^

Oops.

7b8033cfca3452 Matti Vaittinen  2019-11-16  466  				return child;
7b8033cfca3452 Matti Vaittinen  2019-11-16  467  			}
7b8033cfca3452 Matti Vaittinen  2019-11-16  468  			if (ret < 0) {
7b8033cfca3452 Matti Vaittinen  2019-11-16  469  				dev_err(parent,
7b8033cfca3452 Matti Vaittinen  2019-11-16  470  					"invalid fw match. Use raw_val?\n");
7b8033cfca3452 Matti Vaittinen  2019-11-16  471  				fwnode_handle_put(child);
7b8033cfca3452 Matti Vaittinen  2019-11-16  472  				break;
7b8033cfca3452 Matti Vaittinen  2019-11-16  473  			}
7b8033cfca3452 Matti Vaittinen  2019-11-16  474  		}
7b8033cfca3452 Matti Vaittinen  2019-11-16  475  		kfree(val);
7b8033cfca3452 Matti Vaittinen  2019-11-16  476  	}
7b8033cfca3452 Matti Vaittinen  2019-11-16  477  	if (init_data->of_match)
7b8033cfca3452 Matti Vaittinen  2019-11-16  478  		fw = fwnode_get_named_child_node(fw, init_data->of_match);
7b8033cfca3452 Matti Vaittinen  2019-11-16  479  	else
7b8033cfca3452 Matti Vaittinen  2019-11-16  480  		fw = fwnode_handle_get(fw);
7b8033cfca3452 Matti Vaittinen  2019-11-16  481  
7b8033cfca3452 Matti Vaittinen  2019-11-16  482  	return fw;
7b8033cfca3452 Matti Vaittinen  2019-11-16  483  }

---
0-DAY kernel test infrastructure                 Open Source Technology Center
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org Intel Corporation

^ permalink raw reply	[flat|nested] 19+ messages in thread

* Re: [PATCH v4 15/16] leds: Add common LED binding parsing support to LED class/core
  2019-11-18  5:59   ` Dan Carpenter
@ 2019-11-18  6:34     ` Vaittinen, Matti
  0 siblings, 0 replies; 19+ messages in thread
From: Vaittinen, Matti @ 2019-11-18  6:34 UTC (permalink / raw)
  To: dan.carpenter, kbuild
  Cc: robh+dt, mchehab+samsung, sboyd, linux-clk, phil.edworthy,
	hkallweit1, m.szyprowski, mturquette, devicetree, corbet,
	linux-kernel, lee.jones, broonie, lgirdwood, pavel, mark.rutland,
	dmurphy, jeffrey.t.kirsher, a.zummo, hofrat, alexandre.belloni,
	mazziesaccount, linux-rtc, linux-gpio, kbuild-all, linus.walleij,
	jacek.anaszewski, wsa+renesas, linux-leds, bgolaszewski,
	linux-doc

Hello All,

On Mon, 2019-11-18 at 08:59 +0300, Dan Carpenter wrote:
> Hi Matti,
> 
> [auto build test WARNING on 31f4f5b495a62c9a8b15b1c3581acd5efeb9af8c]
> 
> url:    
> https://github.com/0day-ci/linux/commits/Matti-Vaittinen/Support-ROHM-BD71828-PMIC/20191117-030515
> base:    31f4f5b495a62c9a8b15b1c3581acd5efeb9af8c
> 
> If you fix the issue, kindly add following tag
> Reported-by: kbuild test robot <lkp@intel.com>
> Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
> 
> smatch warnings:
> drivers/leds/led-core.c:400 fw_is_match() error: uninitialized symbol
> 'ret'.
> drivers/leds/led-core.c:465 led_find_fwnode() error: double free of
> 'val'

Ouch. The free is clearly a leftover from original code where the
"is_match" was not it's own function. Sorry folks. I'll fix both issues
and send new version.

By the way, I'd appreciate if someone else would also check the
reference-counting for fwnodes - is pumping up the refcount in
led_find_fwnode Ok? My idea is that when-ever the led_find_fwnode
returns an fwnode, the LED class needs to decrease refcount when LED is
unregistered. No matter if fwnode was from device, given by LED driver
or found by the LED class.

Br,
	Matti Vaittinen



^ permalink raw reply	[flat|nested] 19+ messages in thread

end of thread, other threads:[~2019-11-18  6:34 UTC | newest]

Thread overview: 19+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-11-16 18:55 [PATCH v4 00/16] Support ROHM BD71828 PMIC Matti Vaittinen
2019-11-16 18:55 ` [PATCH v4 01/16] dt-bindings: regulator: Document ROHM BD71282 regulator bindings Matti Vaittinen
2019-11-16 18:56 ` [PATCH v4 02/16] dt-bindings: leds: ROHM BD71282 PMIC LED driver Matti Vaittinen
2019-11-16 18:56 ` [PATCH v4 03/16] dt-bindings: mfd: Document ROHM BD71828 bindings Matti Vaittinen
2019-11-16 18:57 ` [PATCH v4 04/16] mfd: rohm PMICs - use platform_device_id to match MFD sub-devices Matti Vaittinen
2019-11-16 18:57 ` [PATCH v4 05/16] mfd: bd71828: Support ROHM BD71828 PMIC - core Matti Vaittinen
2019-11-16 18:58 ` [PATCH v4 06/16] mfd: input: bd71828: Add power-key support Matti Vaittinen
2019-11-16 18:58 ` [PATCH v4 07/16] clk: bd718x7: Support ROHM BD71828 clk block Matti Vaittinen
2019-11-16 18:59 ` [PATCH v4 08/16] regulator: bd718x7: Split driver to common and bd718x7 specific parts Matti Vaittinen
2019-11-16 18:59 ` [PATCH v4 09/16] regulator: bd71828: Basic support for ROHM bd71828 PMIC regulators Matti Vaittinen
2019-11-16 18:59 ` [PATCH v4 10/16] gpio: devres: Add devm_gpiod_get_parent_array Matti Vaittinen
2019-11-16 19:00 ` [PATCH v4 11/16] docs: driver-model: Add missing managed GPIO array get functions Matti Vaittinen
2019-11-16 19:00 ` [PATCH v4 12/16] regulator: bd71828: Add GPIO based run-level control for regulators Matti Vaittinen
2019-11-16 19:01 ` [PATCH v4 13/16] rtc: bd70528 add BD71828 support Matti Vaittinen
2019-11-16 19:01 ` [PATCH v4 14/16] gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs Matti Vaittinen
2019-11-16 19:02 ` [PATCH v4 15/16] leds: Add common LED binding parsing support to LED class/core Matti Vaittinen
2019-11-18  5:59   ` Dan Carpenter
2019-11-18  6:34     ` Vaittinen, Matti
2019-11-16 19:02 ` [PATCH v4 16/16] led: bd71828: Support LED outputs on ROHM BD71828 PMIC Matti Vaittinen

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).