From: Schrempf Frieder <frieder.schrempf@kontron.de>
To: Horia Geanta <horia.geanta@nxp.com>, Adam Ford <aford173@gmail.com>
Cc: "linux-crypto@vger.kernel.org" <linux-crypto@vger.kernel.org>,
"Mark Rutland" <mark.rutland@arm.com>,
Aymen Sghaier <aymen.sghaier@nxp.com>,
"Fabio Estevam" <festevam@gmail.com>,
Herbert Xu <herbert@gondor.apana.org.au>,
"devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
Sascha Hauer <s.hauer@pengutronix.de>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
Rob Herring <robh+dt@kernel.org>,
dl-linux-imx <linux-imx@nxp.com>,
Pengutronix Kernel Team <kernel@pengutronix.de>,
Shawn Guo <shawnguo@kernel.org>,
"David S. Miller" <davem@davemloft.net>,
"linux-arm-kernel@lists.infradead.org"
<linux-arm-kernel@lists.infradead.org>
Subject: Re: [PATCH 1/2] crypto: caam: Change the i.MX8MQ check support all i.MX8M variants
Date: Wed, 11 Dec 2019 14:23:32 +0000 [thread overview]
Message-ID: <d82428e3-326b-db80-2e40-4ef1bdbca060@kontron.de> (raw)
In-Reply-To: <VI1PR0402MB34857B8C5560B912B34674AB985B0@VI1PR0402MB3485.eurprd04.prod.outlook.com>
On 10.12.19 08:56, Horia Geanta wrote:
> On 12/6/2019 9:55 PM, Adam Ford wrote:
>> On Wed, Dec 4, 2019 at 5:38 AM Schrempf Frieder
>> <frieder.schrempf@kontron.de> wrote:
>>>
>>> Hi Adam,
>>>
>>> On 30.11.19 23:51, Adam Ford wrote:
>>>> The i.MX8M Mini uses the same crypto engine as the i.MX8MQ, but
>>>> the driver is restricting the check to just the i.MX8MQ.
>>>>
>>>> This patch lets the driver support all i.MX8M Variants if enabled.
>>>>
>>>> Signed-off-by: Adam Ford <aford173@gmail.com>
>>>
>>> What about the following lines in run_descriptor_deco0()? Does this
>>> condition also apply to i.MX8MM?
>>
>> I think that's a question for NXP. I am not seeing that in the NXP
>> Linux Release, and I don't have an 8MQ to compare.
>>
> IIRC the i.MX BSP releases use the JRI for initializing the RNG,
> and not the DECO register interface.
>
>> I was able to get the driver working on the i.MXMM with the patch.
>>
> You are probably using a newer U-boot, which includes
> commit dfaec76029f2 ("crypto/fsl: instantiate all rng state handles")
>
>> NXP Team,
>>
>> Do you have any opinions on this?
>>
> Since current U-boot initializes both RNG state handles, practically
> instantiate_rng() is a no-op.
>
> A simple experiment is to "lie" about the state_handle_mask, to exercise
> the DECO acquire code (or, as mentioned above, to run with an older U-boot):
>
> @@ -268,12 +272,19 @@ static int instantiate_rng(struct device *ctrldev, int state_handle_mask,
> struct caam_ctrl __iomem *ctrl;
> u32 *desc, status = 0, rdsta_val;
> int ret = 0, sh_idx;
> + static int force_init = 1;
>
> ctrl = (struct caam_ctrl __iomem *)ctrlpriv->ctrl;
> desc = kmalloc(CAAM_CMD_SZ * 7, GFP_KERNEL);
> if (!desc)
> return -ENOMEM;
>
> + if (force_init && (state_handle_mask == 0x3)) {
> + dev_err(ctrldev, "Forcing reinit of RNG state handle 0!\n");
> + force_init = 0;
> + state_handle_mask = 0x2;
> + }
> +
> for (sh_idx = 0; sh_idx < RNG4_MAX_HANDLES; sh_idx++) {
> /*
> * If the corresponding bit is set, this state handle
>
> In this case boot log confirms the DECO cannot be acquired:
> [ 2.137101] caam 30900000.crypto: Forcing reinit of RNG state handle 0!
> [ 2.172293] caam 30900000.crypto: failed to acquire DECO 0
> [ 2.177786] caam 30900000.crypto: failed to instantiate RNG
>
> To sum up, writing to DECORSR is mandatory.
Thanks Horia for providing the details.
Adam, can you update your patch to enable the code in
run_descriptor_deco0() for i.MX8MM?
If I understand this correctly, this is necessary to have the RNG
initialize correctly no matter what version of U-Boot is used.
Thanks,
Frieder
next prev parent reply other threads:[~2019-12-11 14:23 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-11-30 22:51 [PATCH 1/2] crypto: caam: Change the i.MX8MQ check support all i.MX8M variants Adam Ford
2019-11-30 22:51 ` [PATCH 2/2] arm64: dts: imx8mm: Add Crypto CAAM support Adam Ford
2019-12-09 16:23 ` Horia Geanta
2019-12-09 16:47 ` Adam Ford
2019-12-11 14:36 ` Schrempf Frieder
2019-12-04 11:38 ` [PATCH 1/2] crypto: caam: Change the i.MX8MQ check support all i.MX8M variants Schrempf Frieder
2019-12-06 19:55 ` Adam Ford
2019-12-10 7:56 ` Horia Geanta
2019-12-11 14:23 ` Schrempf Frieder [this message]
2019-12-11 14:27 ` Adam Ford
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=d82428e3-326b-db80-2e40-4ef1bdbca060@kontron.de \
--to=frieder.schrempf@kontron.de \
--cc=aford173@gmail.com \
--cc=aymen.sghaier@nxp.com \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=herbert@gondor.apana.org.au \
--cc=horia.geanta@nxp.com \
--cc=kernel@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-crypto@vger.kernel.org \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).