Linux-Devicetree Archive on lore.kernel.org
 help / color / Atom feed
From: "Lothar Waßmann" <LW@KARO-electronics.de>
To: Rob Herring <robh+dt@kernel.org>, Pawel Moll <pawel.moll@arm.com>,
	Mark Rutland <mark.rutland@arm.com>,
	Ian Campbell <ijc+devicetree@hellion.org.uk>,
	Kumar Gala <galak@codeaurora.org>, Rob Landley <rob@landley.net>,
	Dmitry Torokhov <dmitry.torokhov@gmail.com>,
	Thierry Reding <thierry.reding@gmail.com>,
	Grant Likely <grant.likely@linaro.org>,
	Jonathan Cameron <jic23@kernel.org>,
	Shawn Guo <shawn.guo@linaro.org>,
	Silvio F <silvio.fricke@gmail.com>,
	Guennadi Liakhovetski <g.liakhovetski@gmx.de>,
	Jingoo Han <jg1.han@samsung.com>,
	Fugang Duan <B38611@freescale.com>,
	Sachin Kamat <sachin.kamat@linaro.org>,
	devicetree@vger.kernel.org, linux-doc@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-input@vger.kernel.org
Cc: "Lothar Waßmann" <LW@KARO-electronics.de>
Subject: [PATCHv3 3/4] Input: edt-ft5x06: Add DT support
Date: Fri, 17 Jan 2014 13:28:37 +0100
Message-ID: <1389961718-8130-4-git-send-email-LW@KARO-electronics.de> (raw)
In-Reply-To: <1389961718-8130-1-git-send-email-LW@KARO-electronics.de>


Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
---
 .../bindings/input/touchscreen/edt-ft5x06.txt      |   29 +++++
 drivers/input/touchscreen/edt-ft5x06.c             |  121 +++++++++++++++++---
 2 files changed, 132 insertions(+), 18 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt

diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
new file mode 100644
index 0000000..826b564
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
@@ -0,0 +1,29 @@
+* EDT FT5x06 Multiple Touch Controller
+
+Required properties:
+- compatible: must be "edt,ft5x06"
+- reg: i2c slave address
+- interrupt-parent: the phandle for the interrupt controller
+- interrupts: touch controller interrupt
+
+Optional properties:
+- reset-gpios: the gpio pin to be used for resetting the controller
+- wake-gpios:  the gpio pin to be used for waking up the controller
+
+  The following properties provide default values for the
+  corresponding parameters (see Documentation/input/edt-ft5x06.txt)
+- edt,threshold: allows setting the "click"-threshold in the range from 20 to 80.
+- edt,gain: sensitivity (0..31) (lower value -> higher sensitivity)
+- edt,offset: edge compensation (0..31)
+- edt,report-rate: report rate (3..14) events per 100ms
+
+Example:
+
+	edt_ft5x06@38 {
+		compatible = "edt,ft5x06";
+		reg = <0x38>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <5 0>;
+		reset-gpios = <&gpio2 6 1>;
+		wake-gpios = <&gpio4 9 0>;
+	};
diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
index 583c053..ec6b3e5 100644
--- a/drivers/input/touchscreen/edt-ft5x06.c
+++ b/drivers/input/touchscreen/edt-ft5x06.c
@@ -33,6 +33,7 @@
 #include <linux/debugfs.h>
 #include <linux/slab.h>
 #include <linux/gpio.h>
+#include <linux/of_gpio.h>
 #include <linux/input/mt.h>
 #include <linux/input/edt-ft5x06.h>
 
@@ -65,6 +66,10 @@ struct edt_ft5x06_ts_data {
 	u16 num_x;
 	u16 num_y;
 
+	int reset_pin;
+	int irq_pin;
+	int wake_pin;
+
 #if defined(CONFIG_DEBUG_FS)
 	struct dentry *debug_dir;
 	u8 *raw_buffer;
@@ -481,7 +486,7 @@ static int edt_ft5x06_debugfs_mode_set(void *data, u64 mode)
 
 	if (mode != tsdata->factory_mode) {
 		retval = mode ? edt_ft5x06_factory_mode(tsdata) :
-			        edt_ft5x06_work_mode(tsdata);
+				edt_ft5x06_work_mode(tsdata);
 	}
 
 	mutex_unlock(&tsdata->mutex);
@@ -619,24 +624,37 @@ edt_ft5x06_ts_teardown_debugfs(struct edt_ft5x06_ts_data *tsdata)
 
 
 static int edt_ft5x06_ts_reset(struct i2c_client *client,
-					 int reset_pin)
+			struct edt_ft5x06_ts_data *tsdata)
 {
 	int error;
 
-	if (gpio_is_valid(reset_pin)) {
+	if (gpio_is_valid(tsdata->wake_pin)) {
+		error = devm_gpio_request_one(&client->dev, tsdata->wake_pin,
+					GPIOF_OUT_INIT_LOW, "edt-ft5x06 wake");
+		if (error) {
+			dev_err(&client->dev,
+				"Failed to request GPIO %d as wake pin, error %d\n",
+				tsdata->wake_pin, error);
+			return error;
+		}
+
+		mdelay(5);
+		gpio_set_value(tsdata->wake_pin, 1);
+	}
+	if (gpio_is_valid(tsdata->reset_pin)) {
 		/* this pulls reset down, enabling the low active reset */
-		error = devm_gpio_request_one(&client->dev, reset_pin,
+		error = devm_gpio_request_one(&client->dev, tsdata->reset_pin,
 					GPIOF_OUT_INIT_LOW,
 					"edt-ft5x06 reset");
 		if (error) {
 			dev_err(&client->dev,
 				"Failed to request GPIO %d as reset pin, error %d\n",
-				reset_pin, error);
+				tsdata->reset_pin, error);
 			return error;
 		}
 
 		mdelay(50);
-		gpio_set_value(reset_pin, 1);
+		gpio_set_value(tsdata->reset_pin, 1);
 		mdelay(100);
 	}
 
@@ -677,6 +695,29 @@ static int edt_ft5x06_ts_identify(struct i2c_client *client,
 	    pdata->name <= edt_ft5x06_attr_##name.limit_high)		\
 		edt_ft5x06_register_write(tsdata, reg, pdata->name)
 
+#define EDT_GET_PROP(name, var, reg) {					\
+	u32 val;							\
+	if (of_property_read_u32(np, name, &val) == 0) {		\
+		if (val >= edt_ft5x06_attr_##var.limit_low &&		\
+			val <= edt_ft5x06_attr_##var.limit_high)	\
+			edt_ft5x06_register_write(tsdata, reg, val);	\
+		else							\
+			pr_err("edt_ft5x06: property %s (%u) is out of range: %u..%u", \
+				name, val,  edt_ft5x06_attr_##var.limit_low, \
+				edt_ft5x06_attr_##var.limit_high);	\
+	}								\
+}
+
+static void edt_ft5x06_ts_get_dt_defaults(struct device_node *np,
+					struct edt_ft5x06_ts_data *tsdata)
+{
+	/* pick up defaults from the DT data */
+	EDT_GET_PROP("edt,threshold", threshold, WORK_REGISTER_THRESHOLD);
+	EDT_GET_PROP("edt,gain", gain, WORK_REGISTER_GAIN);
+	EDT_GET_PROP("edt,offset", offset, WORK_REGISTER_OFFSET);
+	EDT_GET_PROP("edt,report-rate", report_rate, WORK_REGISTER_REPORT_RATE);
+}
+
 static void
 edt_ft5x06_ts_get_defaults(struct edt_ft5x06_ts_data *tsdata,
 			   const struct edt_ft5x06_platform_data *pdata)
@@ -704,6 +745,33 @@ edt_ft5x06_ts_get_parameters(struct edt_ft5x06_ts_data *tsdata)
 	tsdata->num_y = edt_ft5x06_register_read(tsdata, WORK_REGISTER_NUM_Y);
 }
 
+#ifdef CONFIG_OF
+static int edt_ft5x06_i2c_ts_probe_dt(struct device *dev,
+				struct edt_ft5x06_ts_data *tsdata)
+{
+	struct device_node *np = dev->of_node;
+
+	if (!np)
+		return -ENODEV;
+
+	/*
+	 * irq_pin is not needed for DT setup.
+	 * irq is associated via 'interrupts' property in DT
+	 */
+	tsdata->irq_pin = -EINVAL;
+	tsdata->reset_pin = of_get_named_gpio(np, "reset-gpios", 0);
+	tsdata->wake_pin = of_get_named_gpio(np, "wake-gpios", 0);
+
+	return 0;
+}
+#else
+static inline int edt_ft5x06_i2c_ts_probe_dt(struct device *dev,
+					struct edt_ft5x06_i2c_ts_data *tsdata)
+{
+	return -ENODEV;
+}
+#endif
+
 static int edt_ft5x06_ts_probe(struct i2c_client *client,
 					 const struct i2c_device_id *id)
 {
@@ -716,29 +784,42 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
 
 	dev_dbg(&client->dev, "probing for EDT FT5x06 I2C\n");
 
+	tsdata = devm_kzalloc(&client->dev, sizeof(*tsdata), GFP_KERNEL);
+	if (!tsdata) {
+		dev_err(&client->dev, "failed to allocate driver data.\n");
+		return -ENOMEM;
+	}
+
 	if (!pdata) {
-		dev_err(&client->dev, "no platform data?\n");
-		return -EINVAL;
+		error = edt_ft5x06_i2c_ts_probe_dt(&client->dev, tsdata);
+		if (error) {
+			dev_err(&client->dev,
+				"DT probe failed and no platform data present\n");
+			return error;
+		}
+	} else {
+		tsdata->reset_pin = pdata->reset_pin;
+		tsdata->irq_pin = pdata->irq_pin;
+		tsdata->wake_pin = -EINVAL;
 	}
 
-	error = edt_ft5x06_ts_reset(client, pdata->reset_pin);
+	error = edt_ft5x06_ts_reset(client, tsdata);
 	if (error)
 		return error;
 
-	if (gpio_is_valid(pdata->irq_pin)) {
-		error = devm_gpio_request_one(&client->dev, pdata->irq_pin,
-					 GPIOF_IN, "edt-ft5x06 irq");
+	if (gpio_is_valid(tsdata->irq_pin)) {
+		error = devm_gpio_request_one(&client->dev, tsdata->irq_pin,
+					GPIOF_IN, "edt-ft5x06 irq");
 		if (error) {
 			dev_err(&client->dev,
 				"Failed to request GPIO %d, error %d\n",
-				pdata->irq_pin, error);
+				tsdata->irq_pin, error);
 			return error;
 		}
 	}
 
-	tsdata = devm_kzalloc(&client->dev, sizeof(*tsdata), GFP_KERNEL);
 	input = devm_input_allocate_device(&client->dev);
-	if (!tsdata || !input) {
+	if (!input) {
 		dev_err(&client->dev, "failed to allocate input device.\n");
 		return -ENOMEM;
 	}
@@ -754,7 +835,11 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
 		return error;
 	}
 
-	edt_ft5x06_ts_get_defaults(tsdata, pdata);
+	if (!pdata)
+		edt_ft5x06_ts_get_dt_defaults(client->dev.of_node, tsdata);
+	else
+		edt_ft5x06_ts_get_defaults(tsdata, pdata);
+
 	edt_ft5x06_ts_get_parameters(tsdata);
 
 	dev_dbg(&client->dev,
@@ -807,8 +892,8 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
 	device_init_wakeup(&client->dev, 1);
 
 	dev_dbg(&client->dev,
-		"EDT FT5x06 initialized: IRQ pin %d, Reset pin %d.\n",
-		pdata->irq_pin, pdata->reset_pin);
+		"EDT FT5x06 initialized: IRQ %d, WAKE pin %d, Reset pin %d.\n",
+		client->irq, tsdata->wake_pin, tsdata->reset_pin);
 
 	return 0;
 }
-- 
1.7.2.5


  parent reply index

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2014-01-17 12:28 Lothar Waßmann
2014-01-17 12:28 ` [PATCHv3 1/4] DT: Add vendor prefix for Emerging Display Technologies Lothar Waßmann
2014-01-17 22:18   ` Rob Herring
2014-01-17 12:28 ` [PATCHv3 2/4] Input: edt_ft5x06: use devm_* functions where appropriate Lothar Waßmann
2014-01-17 12:28 ` Lothar Waßmann [this message]
2014-01-17 12:28 ` [PATCHv3 4/4] Input: edt-ft5x06 adjust reset delays according to datasheet Lothar Waßmann

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1389961718-8130-4-git-send-email-LW@KARO-electronics.de \
    --to=lw@karo-electronics.de \
    --cc=B38611@freescale.com \
    --cc=devicetree@vger.kernel.org \
    --cc=dmitry.torokhov@gmail.com \
    --cc=g.liakhovetski@gmx.de \
    --cc=galak@codeaurora.org \
    --cc=grant.likely@linaro.org \
    --cc=ijc+devicetree@hellion.org.uk \
    --cc=jg1.han@samsung.com \
    --cc=jic23@kernel.org \
    --cc=linux-doc@vger.kernel.org \
    --cc=linux-input@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=pawel.moll@arm.com \
    --cc=rob@landley.net \
    --cc=robh+dt@kernel.org \
    --cc=sachin.kamat@linaro.org \
    --cc=shawn.guo@linaro.org \
    --cc=silvio.fricke@gmail.com \
    --cc=thierry.reding@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-Devicetree Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-devicetree/0 linux-devicetree/git/0.git
	git clone --mirror https://lore.kernel.org/linux-devicetree/1 linux-devicetree/git/1.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-devicetree linux-devicetree/ https://lore.kernel.org/linux-devicetree \
		devicetree@vger.kernel.org
	public-inbox-index linux-devicetree

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-devicetree


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git