Linux-Devicetree Archive on lore.kernel.org
 help / color / Atom feed
From: Moritz Fischer <mdf@kernel.org>
To: linux-fpga@vger.kernel.org
Cc: robh+dt@kernel.org, mark.rutland@arm.com,
	linux-arm-kernel@lists.infradead.org, gregkh@linuxfoundation.org,
	"Moritz Fischer" <mdf@kernel.org>,
	"Michal Simek" <michal.simek@xilinx.com>,
	"Sören Brinkmann" <soren.brinkmann@xilinx.com>,
	linux-kernel@vger.kernel.org, devicetree@vger.kernel.org
Subject: [PATCH v3 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler
Date: Fri, 17 Mar 2017 13:11:13 -0700
Message-ID: <1489781473-30772-2-git-send-email-mdf@kernel.org> (raw)
In-Reply-To: <1489781473-30772-1-git-send-email-mdf@kernel.org>

This adds support for the Xilinx LogiCORE PR Decoupler
soft-ip that does decoupling of PR regions in the FPGA
fabric during partial reconfiguration.

Signed-off-by: Moritz Fischer <mdf@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
---
Changes from v2:
- Added Michal's Signed-off-by
- Added "xlnx,pr-decoupler" unversioned fallback

Changes from v1:
- Added Michal as Co-Author since I pulled in some of his code
- Reworked clk handling in _remove()
- Pulled in Michal's version of show_enable(), ditched priv->enabled

---
 drivers/fpga/Kconfig               |   9 +++
 drivers/fpga/Makefile              |   1 +
 drivers/fpga/xilinx-pr-decoupler.c | 148 +++++++++++++++++++++++++++++++++++++
 3 files changed, 158 insertions(+)
 create mode 100644 drivers/fpga/xilinx-pr-decoupler.c

diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
index ce861a2..ce0c91d 100644
--- a/drivers/fpga/Kconfig
+++ b/drivers/fpga/Kconfig
@@ -63,6 +63,15 @@ config ALTERA_FREEZE_BRIDGE
 	  isolate one region of the FPGA from the busses while that
 	  region is being reprogrammed.
 
+config XILINX_PR_DECOUPLER
+	tristate "Xilinx LogiCORE PR Decoupler"
+	depends on FPGA_BRIDGE
+	help
+	  Say Y to enable drivers for Xilinx LogiCORE PR Decoupler.
+	  The PR Decoupler exists in the FPGA fabric to isolate one
+	  region of the FPGA from the busses while that region is
+	  being reprogrammed during partial reconfig.
+
 endif # FPGA
 
 endmenu
diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
index 8df07bc..ba94b79 100644
--- a/drivers/fpga/Makefile
+++ b/drivers/fpga/Makefile
@@ -14,6 +14,7 @@ obj-$(CONFIG_FPGA_MGR_ZYNQ_FPGA)	+= zynq-fpga.o
 obj-$(CONFIG_FPGA_BRIDGE)		+= fpga-bridge.o
 obj-$(CONFIG_SOCFPGA_FPGA_BRIDGE)	+= altera-hps2fpga.o altera-fpga2sdram.o
 obj-$(CONFIG_ALTERA_FREEZE_BRIDGE)	+= altera-freeze-bridge.o
+obj-$(CONFIG_XILINX_PR_DECOUPLER)	+= xilinx-pr-decoupler.o
 
 # High Level Interfaces
 obj-$(CONFIG_FPGA_REGION)		+= fpga-region.o
diff --git a/drivers/fpga/xilinx-pr-decoupler.c b/drivers/fpga/xilinx-pr-decoupler.c
new file mode 100644
index 0000000..dd37b1c
--- /dev/null
+++ b/drivers/fpga/xilinx-pr-decoupler.c
@@ -0,0 +1,148 @@
+/*
+ * Copyright (c) 2017, National Instruments Corp.
+ * Copyright (c) 2017, Xilix Inc
+ *
+ * FPGA Bridge Driver for the Xilinx LogiCORE Partial Reconfiguration
+ * Decoupler IP Core.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/of_device.h>
+#include <linux/module.h>
+#include <linux/fpga/fpga-bridge.h>
+
+#define CTRL_CMD_DECOUPLE	BIT(0)
+#define CTRL_CMD_COUPLE		~BIT(0)
+
+struct xlnx_pr_decoupler_data {
+	void __iomem *io_base;
+	struct clk *clk;
+};
+
+static int xlnx_pr_decoupler_enable_set(struct fpga_bridge *bridge, bool enable)
+{
+	int err;
+	struct xlnx_pr_decoupler_data *priv = bridge->priv;
+
+	err = clk_enable(priv->clk);
+	if (err)
+		return err;
+
+	if (enable)
+		writel(CTRL_CMD_COUPLE, priv->io_base);
+	else
+		writel(CTRL_CMD_DECOUPLE, priv->io_base);
+
+	clk_disable(priv->clk);
+
+	return 0;
+}
+
+static int xlnx_pr_decoupler_enable_show(struct fpga_bridge *bridge)
+{
+	const struct xlnx_pr_decoupler_data *priv = bridge->priv;
+	u32 status;
+	int err;
+
+	err = clk_enable(priv->clk);
+	if (err)
+		return err;
+
+	status = readl(priv->io_base);
+
+	clk_disable(priv->clk);
+
+	return !status;
+}
+
+static struct fpga_bridge_ops xlnx_pr_decoupler_br_ops = {
+	.enable_set = xlnx_pr_decoupler_enable_set,
+	.enable_show = xlnx_pr_decoupler_enable_show,
+};
+
+static const struct of_device_id xlnx_pr_decoupler_of_match[] = {
+	{ .compatible = "xlnx,pr-decoupler-1.00", },
+	{ .compatible = "xlnx,pr-decoupler", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, xlnx_pr_decoupler_of_match);
+
+static int xlnx_pr_decoupler_probe(struct platform_device *pdev)
+{
+	struct xlnx_pr_decoupler_data *priv;
+	int err;
+	struct resource *res;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->io_base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(priv->io_base))
+		return PTR_ERR(priv->io_base);
+
+	priv->clk = devm_clk_get(&pdev->dev, "aclk");
+	if (IS_ERR(priv->clk)) {
+		dev_err(&pdev->dev, "input clock not found\n");
+		return PTR_ERR(priv->clk);
+	}
+
+	err = clk_prepare_enable(priv->clk);
+	if (err) {
+		dev_err(&pdev->dev, "unable to enable clock\n");
+		return err;
+	}
+
+	clk_disable(priv->clk);
+
+	err = fpga_bridge_register(&pdev->dev, "Xilinx PR Decoupler",
+				   &xlnx_pr_decoupler_br_ops, priv);
+
+	if (err) {
+		dev_err(&pdev->dev, "unable to register Xilinx PR Decoupler");
+		clk_unprepare(priv->clk);
+		return err;
+	}
+
+	return 0;
+}
+
+static int xlnx_pr_decoupler_remove(struct platform_device *pdev)
+{
+	struct fpga_bridge *bridge = platform_get_drvdata(pdev);
+	struct xlnx_pr_decoupler_data *p = bridge->priv;
+
+	fpga_bridge_unregister(&pdev->dev);
+
+	clk_unprepare(p->clk);
+
+	return 0;
+}
+
+static struct platform_driver xlnx_pr_decoupler_driver = {
+	.probe = xlnx_pr_decoupler_probe,
+	.remove = xlnx_pr_decoupler_remove,
+	.driver = {
+		.name = "xlnx_pr_decoupler",
+		.of_match_table = of_match_ptr(xlnx_pr_decoupler_of_match),
+	},
+};
+
+module_platform_driver(xlnx_pr_decoupler_driver);
+
+MODULE_DESCRIPTION("Xilinx Partial Reconfiguration Decoupler");
+MODULE_AUTHOR("Moritz Fischer <mdf@kernel.org>");
+MODULE_AUTHOR("Michal Simek <michal.simek@xilinx.com>");
+MODULE_LICENSE("GPL v2");
-- 
2.7.4

  reply index

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-03-17 20:11 [PATCH v3 1/2] doc: Add bindings document for Xilinx LogiCore " Moritz Fischer
2017-03-17 20:11 ` Moritz Fischer [this message]
2017-03-20 10:02   ` [PATCH v3 2/2] fpga: Add support for Xilinx LogiCORE " Michal Simek
2017-03-20 16:28   ` Alan Tull
     [not found]   ` <1489781473-30772-2-git-send-email-mdf-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
2017-03-20 16:51     ` kbuild test robot
2017-03-20 10:03 ` [PATCH v3 1/2] doc: Add bindings document for Xilinx LogiCore " Michal Simek
2017-03-20 16:17 ` Alan Tull
     [not found] ` <1489781473-30772-1-git-send-email-mdf-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
2017-03-24 14:59   ` Rob Herring
2017-03-24 15:23     ` Moritz Fischer
2017-03-24 17:25       ` Alan Tull
2017-03-24 18:07         ` Moritz Fischer

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1489781473-30772-2-git-send-email-mdf@kernel.org \
    --to=mdf@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-fpga@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=michal.simek@xilinx.com \
    --cc=robh+dt@kernel.org \
    --cc=soren.brinkmann@xilinx.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-Devicetree Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-devicetree/0 linux-devicetree/git/0.git
	git clone --mirror https://lore.kernel.org/linux-devicetree/1 linux-devicetree/git/1.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-devicetree linux-devicetree/ https://lore.kernel.org/linux-devicetree \
		devicetree@vger.kernel.org
	public-inbox-index linux-devicetree

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-devicetree


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git