From mboxrd@z Thu Jan 1 00:00:00 1970 From: Anson Huang Subject: [PATCH V2 2/2] cpufreq: imx6q: add 696MHz operating point for i.mx6ul Date: Sat, 6 Jan 2018 18:42:40 +0800 Message-ID: <1515235360-1628-2-git-send-email-Anson.Huang@nxp.com> References: <1515235360-1628-1-git-send-email-Anson.Huang@nxp.com> Mime-Version: 1.0 Content-Type: text/plain Return-path: In-Reply-To: <1515235360-1628-1-git-send-email-Anson.Huang@nxp.com> Sender: linux-kernel-owner@vger.kernel.org To: shawnguo@kernel.org, kernel@pengutronix.de, fabio.estevam@nxp.com, robh+dt@kernel.org, mark.rutland@arm.com, rjw@rjwysocki.net, linux@armlinux.org.uk, viresh.kumar@linaro.org, rafael@kernel.org Cc: linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-pm@vger.kernel.org List-Id: devicetree@vger.kernel.org Add 696MHz operating point for i.MX6UL, only for those parts with speed grading fuse set to 2b'10 supports 696MHz operating point, so, speed grading check is also added for i.MX6UL in this patch, the clock tree for each operating point are as below: 696MHz: pll1 696000000 pll1_bypass 696000000 pll1_sys 696000000 pll1_sw 696000000 arm 696000000 528MHz: pll2 528000000 pll2_bypass 528000000 pll2_bus 528000000 ca7_secondary_sel 528000000 step 528000000 pll1_sw 528000000 arm 528000000 396MHz: pll2_pfd2_396m 396000000 ca7_secondary_sel 396000000 step 396000000 pll1_sw 396000000 arm 396000000 198MHz: pll2_pfd2_396m 396000000 ca7_secondary_sel 396000000 step 396000000 pll1_sw 396000000 arm 198000000 Signed-off-by: Anson Huang --- changes since v1: redo the patch based on linux-next-pm. drivers/cpufreq/imx6q-cpufreq.c | 46 ++++++++++++++++++++++++++++++++++++++++- 1 file changed, 45 insertions(+), 1 deletion(-) diff --git a/drivers/cpufreq/imx6q-cpufreq.c b/drivers/cpufreq/imx6q-cpufreq.c index 8bfb077..741f22e 100644 --- a/drivers/cpufreq/imx6q-cpufreq.c +++ b/drivers/cpufreq/imx6q-cpufreq.c @@ -136,6 +136,10 @@ static int imx6q_set_target(struct cpufreq_policy *policy, unsigned int index) clks[PLL2_PFD2_396M].clk); clk_set_parent(clks[STEP].clk, clks[SECONDARY_SEL].clk); clk_set_parent(clks[PLL1_SW].clk, clks[STEP].clk); + if (freq_hz > clk_get_rate(clks[PLL2_BUS].clk)) { + clk_set_rate(clks[PLL1_SYS].clk, new_freq * 1000); + clk_set_parent(clks[PLL1_SW].clk, clks[PLL1_SYS].clk); + } } else { clk_set_parent(clks[STEP].clk, clks[PLL2_PFD2_396M].clk); clk_set_parent(clks[PLL1_SW].clk, clks[STEP].clk); @@ -260,6 +264,43 @@ static void imx6q_opp_check_speed_grading(struct device *dev) of_node_put(np); } +#define OCOTP_CFG3_6UL_SPEED_696MHZ 0x2 + +static void imx6ul_opp_check_speed_grading(struct device *dev) +{ + struct device_node *np; + void __iomem *base; + u32 val; + + np = of_find_compatible_node(NULL, NULL, "fsl,imx6ul-ocotp"); + if (!np) + return; + + base = of_iomap(np, 0); + if (!base) { + dev_err(dev, "failed to map ocotp\n"); + goto put_node; + } + + /* + * Speed GRADING[1:0] defines the max speed of ARM: + * 2b'00: Reserved; + * 2b'01: 528000000Hz; + * 2b'10: 696000000Hz; + * 2b'11: Reserved; + * We need to set the max speed of ARM according to fuse map. + */ + val = readl_relaxed(base + OCOTP_CFG3); + val >>= OCOTP_CFG3_SPEED_SHIFT; + val &= 0x3; + if (val != OCOTP_CFG3_6UL_SPEED_696MHZ) + if (dev_pm_opp_disable(dev, 696000000)) + dev_warn(dev, "failed to disable 696MHz OPP\n"); + iounmap(base); +put_node: + of_node_put(np); +} + static int imx6q_cpufreq_probe(struct platform_device *pdev) { struct device_node *np; @@ -314,7 +355,10 @@ static int imx6q_cpufreq_probe(struct platform_device *pdev) goto put_reg; } - imx6q_opp_check_speed_grading(cpu_dev); + if (of_machine_is_compatible("fsl,imx6ul")) + imx6ul_opp_check_speed_grading(cpu_dev); + else + imx6q_opp_check_speed_grading(cpu_dev); /* Because we have added the OPPs here, we must free them */ free_opp = true; -- 1.9.1