* [PATCH v3 1/8] dt-bindings: display: xlnx: Add bindings for Xilinx display pipeline
@ 2018-01-16 1:57 Hyun Kwon
[not found] ` <1516067831-11382-1-git-send-email-hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
` (3 more replies)
0 siblings, 4 replies; 17+ messages in thread
From: Hyun Kwon @ 2018-01-16 1:57 UTC (permalink / raw)
To: dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW,
devicetree-u79uwXL29TY76Z2rM5mHXA
Cc: Michal Simek, Rob Herring, Daniel Vetter, Laurent Pinchart, Hyun Kwon
The dt binding for Xilinx display pipeline. The pipeline can be
composed with multiple and different types of sub-devices. This node
is to represent the entire pipeline as a single entity.
Signed-off-by: Hyun Kwon <hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
---
v2
- Remove linux specific terms
- Elaborate details, ex regarding port binding
- Rename xlnx,kms to xlnx,display
- Rename the file name to xlnx,display.txt
- Add examples of hardware blocks
---
---
.../bindings/display/xlnx/xlnx,display.txt | 68 ++++++++++++++++++++++
1 file changed, 68 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/xlnx/xlnx,display.txt
diff --git a/Documentation/devicetree/bindings/display/xlnx/xlnx,display.txt b/Documentation/devicetree/bindings/display/xlnx/xlnx,display.txt
new file mode 100644
index 0000000..fde1a35
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/xlnx/xlnx,display.txt
@@ -0,0 +1,68 @@
+Xilinx Display Pipeline
+-----------------------
+
+Xilinx display pipeline can be designed with various types of multiple IPs:
+IPs hardened on chip, ob board IPs, and soft IPs in programmable logic.
+While each component would need its own node, this node represents
+a whole display pipeline as a single entity by integrating individual subdevice
+with glue logics.
+
+The following illustrates some examples of topology:
+
+A linear pipeline with multiple blocks:
+
+ SoC DMA -> SoC display controller -> SoC display enc
+or,
+ FPGA DMA -> FPGA display controller -> FPGA display enc
+
+A pipeline with branches:
+
+ SoC DMA -> SoC display controller -> SoC display enc
+ |
+ FPGA DMA->
+or,
+ SoC DMA -> SoC display controller -> SoC display enc
+ |
+ -> FPAG display enc
+
+or,
+
+ SoC DMA -> SoC display controller -> SoC display enc
+ | |
+ FPGA display controller -> -> FPGA display enc
+
+Required properties:
+
+- compatible: Must be "xlnx,display".
+
+- ports: phandles for ports of display controller subdevice.
+ In the display controller port nodes, topology for entire pipeline
+ should be described using the DT bindings defined in
+ Documentation/devicetree/bindings/graph.txt.
+
+Example:
+
+ xlnx_display {
+ compatible = "xlnx,display";
+ ports = <&display_controller_port>;
+ };
+
+ display_controller {
+ ...
+ display_controller_port: port@0 {
+ display_controller_ep: endpoint {
+ remote-endpoint = <&dp_controller_ep>;
+ };
+ };
+ ...
+ };
+
+ dp_controller {
+ ...
+ dp_controller_port: port@0 {
+ dp_controller_ep: endpoint {
+ remote-endpoint = <&display_controller_ep>;
+ };
+ };
+ ...
+ };
--
2.7.4
This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH v3 2/8] drm: xlnx: Xilinx DRM KMS driver
[not found] ` <1516067831-11382-1-git-send-email-hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
@ 2018-01-16 1:57 ` Hyun Kwon
[not found] ` <1516067831-11382-2-git-send-email-hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
2018-01-17 8:20 ` Daniel Vetter
2018-01-16 1:57 ` [PATCH v3 3/8] dt-bindings: display: xlnx: Add ZynqMP DP subsystem bindings Hyun Kwon
` (3 subsequent siblings)
4 siblings, 2 replies; 17+ messages in thread
From: Hyun Kwon @ 2018-01-16 1:57 UTC (permalink / raw)
To: dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW,
devicetree-u79uwXL29TY76Z2rM5mHXA
Cc: Michal Simek, Rob Herring, Daniel Vetter, Laurent Pinchart, Hyun Kwon
Xilinx has various platforms for display, where users can create
using multiple IPs in the programmable FPGA fabric, or where
some hardened piepline is available on the chip. Furthermore,
hardened pipeline can also interact with soft logics in FPGA.
The Xilinx DRM KMS is to integrate multiple subdevices and to represent
the entire pipeline as a single DRM device. The driver includes helpers
(ex, framebuffer and gem helpers) and glue logics (ex, crtc interface).
Signed-off-by: Hyun Kwon <hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
---
v3
- Add Laurent as a maintainer
- Fix multiple-reference on gem objects
v2
- Change the SPDX identifier format
- Merge patches(crtc, gem, fb) into single one
v2 of xlnx_drv
- Rename kms to display in xlnx_drv
- Replace some xlnx specific fb helper with common helpers in xlnx_drv
- Don't set the commit tail callback in xlnx_drv
- Support 'ports' graph binding in xlnx_drv
v2 of xlnx_fb
- Remove wrappers in xlnx_fb
- Replace some functions with drm core helpers in xlnx_fb
---
---
MAINTAINERS | 9 +
drivers/gpu/drm/Kconfig | 2 +
drivers/gpu/drm/Makefile | 1 +
drivers/gpu/drm/xlnx/Kconfig | 12 ++
drivers/gpu/drm/xlnx/Makefile | 2 +
drivers/gpu/drm/xlnx/xlnx_crtc.c | 203 ++++++++++++++++++
drivers/gpu/drm/xlnx/xlnx_crtc.h | 78 +++++++
drivers/gpu/drm/xlnx/xlnx_drv.c | 447 +++++++++++++++++++++++++++++++++++++++
drivers/gpu/drm/xlnx/xlnx_drv.h | 30 +++
drivers/gpu/drm/xlnx/xlnx_fb.c | 298 ++++++++++++++++++++++++++
drivers/gpu/drm/xlnx/xlnx_fb.h | 33 +++
drivers/gpu/drm/xlnx/xlnx_gem.c | 47 ++++
drivers/gpu/drm/xlnx/xlnx_gem.h | 26 +++
13 files changed, 1188 insertions(+)
create mode 100644 drivers/gpu/drm/xlnx/Kconfig
create mode 100644 drivers/gpu/drm/xlnx/Makefile
create mode 100644 drivers/gpu/drm/xlnx/xlnx_crtc.c
create mode 100644 drivers/gpu/drm/xlnx/xlnx_crtc.h
create mode 100644 drivers/gpu/drm/xlnx/xlnx_drv.c
create mode 100644 drivers/gpu/drm/xlnx/xlnx_drv.h
create mode 100644 drivers/gpu/drm/xlnx/xlnx_fb.c
create mode 100644 drivers/gpu/drm/xlnx/xlnx_fb.h
create mode 100644 drivers/gpu/drm/xlnx/xlnx_gem.c
create mode 100644 drivers/gpu/drm/xlnx/xlnx_gem.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 2811a21..dc84346 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4682,6 +4682,15 @@ F: drivers/gpu/drm/etnaviv/
F: include/uapi/drm/etnaviv_drm.h
F: Documentation/devicetree/bindings/display/etnaviv/
+DRM DRIVERS FOR XILINX
+M: Hyun Kwon <hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
+M: Laurent Pinchart <laurent.pinchart-ryLnwIuWjnjg/C1BVhZhaw@public.gmane.org>
+L: dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW@public.gmane.org
+S: Maintained
+F: drivers/gpu/drm/xlnx/
+F: Documentation/devicetree/bindings/display/xlnx/
+T: git git://anongit.freedesktop.org/drm/drm-misc
+
DRM DRIVERS FOR ZTE ZX
M: Shawn Guo <shawnguo-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
L: dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW@public.gmane.org
diff --git a/drivers/gpu/drm/Kconfig b/drivers/gpu/drm/Kconfig
index 22ee5a1..f3c71e3 100644
--- a/drivers/gpu/drm/Kconfig
+++ b/drivers/gpu/drm/Kconfig
@@ -282,6 +282,8 @@ source "drivers/gpu/drm/tinydrm/Kconfig"
source "drivers/gpu/drm/pl111/Kconfig"
+source "drivers/gpu/drm/xlnx/Kconfig"
+
# Keep legacy drivers last
menuconfig DRM_LEGACY
diff --git a/drivers/gpu/drm/Makefile b/drivers/gpu/drm/Makefile
index 92550dd..2f44c77 100644
--- a/drivers/gpu/drm/Makefile
+++ b/drivers/gpu/drm/Makefile
@@ -103,3 +103,4 @@ obj-$(CONFIG_DRM_ZTE) += zte/
obj-$(CONFIG_DRM_MXSFB) += mxsfb/
obj-$(CONFIG_DRM_TINYDRM) += tinydrm/
obj-$(CONFIG_DRM_PL111) += pl111/
+obj-$(CONFIG_DRM_XLNX) += xlnx/
diff --git a/drivers/gpu/drm/xlnx/Kconfig b/drivers/gpu/drm/xlnx/Kconfig
new file mode 100644
index 0000000..19fd7cd
--- /dev/null
+++ b/drivers/gpu/drm/xlnx/Kconfig
@@ -0,0 +1,12 @@
+config DRM_XLNX
+ tristate "Xilinx DRM KMS Driver"
+ depends on DRM && OF
+ select DRM_KMS_HELPER
+ select DRM_KMS_CMA_HELPER
+ select DRM_GEM_CMA_HELPER
+ help
+ Xilinx DRM KMS driver. Choose this option if you have
+ a Xilinx SoCs with hardened display pipeline or soft
+ display pipeline using Xilinx IPs in FPGA. This module
+ provides the kernel mode setting functionalities
+ for Xilinx display drivers.
diff --git a/drivers/gpu/drm/xlnx/Makefile b/drivers/gpu/drm/xlnx/Makefile
new file mode 100644
index 0000000..c60a281
--- /dev/null
+++ b/drivers/gpu/drm/xlnx/Makefile
@@ -0,0 +1,2 @@
+xlnx_drm-objs += xlnx_crtc.o xlnx_drv.o xlnx_fb.o xlnx_gem.o
+obj-$(CONFIG_DRM_XLNX) += xlnx_drm.o
diff --git a/drivers/gpu/drm/xlnx/xlnx_crtc.c b/drivers/gpu/drm/xlnx/xlnx_crtc.c
new file mode 100644
index 0000000..89beb9e
--- /dev/null
+++ b/drivers/gpu/drm/xlnx/xlnx_crtc.c
@@ -0,0 +1,203 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx DRM crtc driver
+ *
+ * Copyright (C) 2017 - 2018 Xilinx, Inc.
+ *
+ * Author: Hyun Woo Kwon <hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <drm/drmP.h>
+
+#include <linux/list.h>
+
+#include "xlnx_crtc.h"
+#include "xlnx_drv.h"
+
+/*
+ * Overview
+ * --------
+ *
+ * The Xilinx CRTC layer is to enable the custom interface to CRTC drivers.
+ * The interface is used by Xilinx DRM driver where it needs CRTC
+ * functionailty. CRTC drivers should attach the desired callbacks
+ * to struct xlnx_crtc and register the xlnx_crtc with correcsponding
+ * drm_device. It's highly recommended CRTC drivers register all callbacks
+ * even though many of them are optional.
+ * The CRTC helper simply walks through the registered CRTC device,
+ * and call the callbacks.
+ */
+
+/**
+ * struct xlnx_crtc_helper - Xilinx CRTC helper
+ * @xlnx_crtcs: list of Xilinx CRTC devices
+ * @lock: lock to protect @xlnx_crtcs
+ * @drm: back pointer to DRM core
+ */
+struct xlnx_crtc_helper {
+ struct list_head xlnx_crtcs;
+ struct mutex lock; /* lock for @xlnx_crtcs */
+ struct drm_device *drm;
+};
+
+#define XLNX_CRTC_MAX_HEIGHT_WIDTH UINT_MAX
+
+int xlnx_crtc_helper_enable_vblank(struct xlnx_crtc_helper *helper,
+ unsigned int crtc_id)
+{
+ struct xlnx_crtc *crtc;
+
+ list_for_each_entry(crtc, &helper->xlnx_crtcs, list)
+ if (drm_crtc_index(&crtc->crtc) == crtc_id)
+ if (crtc->enable_vblank)
+ return crtc->enable_vblank(crtc);
+ return -ENODEV;
+}
+
+void xlnx_crtc_helper_disable_vblank(struct xlnx_crtc_helper *helper,
+ unsigned int crtc_id)
+{
+ struct xlnx_crtc *crtc;
+
+ list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
+ if (drm_crtc_index(&crtc->crtc) == crtc_id) {
+ if (crtc->disable_vblank)
+ crtc->disable_vblank(crtc);
+ return;
+ }
+ }
+}
+
+unsigned int xlnx_crtc_helper_get_align(struct xlnx_crtc_helper *helper)
+{
+ struct xlnx_crtc *crtc;
+ unsigned int align = 1, tmp;
+
+ list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
+ if (crtc->get_align) {
+ tmp = crtc->get_align(crtc);
+ align = ALIGN(align, tmp);
+ }
+ }
+
+ return align;
+}
+
+u64 xlnx_crtc_helper_get_dma_mask(struct xlnx_crtc_helper *helper)
+{
+ struct xlnx_crtc *crtc;
+ u64 mask = DMA_BIT_MASK(sizeof(dma_addr_t) * 8), tmp;
+
+ list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
+ if (crtc->get_dma_mask) {
+ tmp = crtc->get_dma_mask(crtc);
+ mask = min(mask, tmp);
+ }
+ }
+
+ return mask;
+}
+
+int xlnx_crtc_helper_get_max_width(struct xlnx_crtc_helper *helper)
+{
+ struct xlnx_crtc *crtc;
+ unsigned int width = XLNX_CRTC_MAX_HEIGHT_WIDTH, tmp;
+
+ list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
+ if (crtc->get_max_width) {
+ tmp = crtc->get_max_width(crtc);
+ width = min(width, tmp);
+ }
+ }
+
+ return width;
+}
+
+int xlnx_crtc_helper_get_max_height(struct xlnx_crtc_helper *helper)
+{
+ struct xlnx_crtc *crtc;
+ unsigned int height = XLNX_CRTC_MAX_HEIGHT_WIDTH, tmp;
+
+ list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
+ if (crtc->get_max_height) {
+ tmp = crtc->get_max_height(crtc);
+ height = min(height, tmp);
+ }
+ }
+
+ return height;
+}
+
+uint32_t xlnx_crtc_helper_get_format(struct xlnx_crtc_helper *helper)
+{
+ struct xlnx_crtc *crtc;
+ u32 format = 0, tmp;
+
+ list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
+ if (crtc->get_format) {
+ tmp = crtc->get_format(crtc);
+ if (format && format != tmp)
+ return 0;
+ format = tmp;
+ }
+ }
+
+ return format;
+}
+
+struct xlnx_crtc_helper *xlnx_crtc_helper_init(struct drm_device *drm)
+{
+ struct xlnx_crtc_helper *helper;
+
+ helper = devm_kzalloc(drm->dev, sizeof(*helper), GFP_KERNEL);
+ if (!helper)
+ return ERR_PTR(-ENOMEM);
+
+ INIT_LIST_HEAD(&helper->xlnx_crtcs);
+ mutex_init(&helper->lock);
+ helper->drm = drm;
+
+ return helper;
+}
+
+void xlnx_crtc_helper_fini(struct drm_device *drm,
+ struct xlnx_crtc_helper *helper)
+{
+ if (WARN_ON(helper->drm != drm))
+ return;
+
+ if (WARN_ON(!list_empty(&helper->xlnx_crtcs)))
+ return;
+
+ mutex_destroy(&helper->lock);
+ devm_kfree(drm->dev, helper);
+}
+
+void xlnx_crtc_register(struct drm_device *drm, struct xlnx_crtc *crtc)
+{
+ struct xlnx_crtc_helper *helper = xlnx_get_crtc_helper(drm);
+
+ mutex_lock(&helper->lock);
+ list_add_tail(&crtc->list, &helper->xlnx_crtcs);
+ mutex_unlock(&helper->lock);
+}
+EXPORT_SYMBOL_GPL(xlnx_crtc_register);
+
+void xlnx_crtc_unregister(struct drm_device *drm, struct xlnx_crtc *crtc)
+{
+ struct xlnx_crtc_helper *helper = xlnx_get_crtc_helper(drm);
+
+ mutex_lock(&helper->lock);
+ list_del(&crtc->list);
+ mutex_unlock(&helper->lock);
+}
+EXPORT_SYMBOL_GPL(xlnx_crtc_unregister);
diff --git a/drivers/gpu/drm/xlnx/xlnx_crtc.h b/drivers/gpu/drm/xlnx/xlnx_crtc.h
new file mode 100644
index 0000000..1498e10
--- /dev/null
+++ b/drivers/gpu/drm/xlnx/xlnx_crtc.h
@@ -0,0 +1,78 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx DRM crtc header
+ *
+ * Copyright (C) 2017 - 2018 Xilinx, Inc.
+ *
+ * Author: Hyun Woo Kwon <hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _XLNX_CRTC_H_
+#define _XLNX_CRTC_H_
+
+/**
+ * struct xlnx_crtc - Xilinx CRTC device
+ * @crtc: DRM CRTC device
+ * @list: list node for Xilinx CRTC device list
+ * @enable_vblank: Enable vblank
+ * @disable_vblank: Disable vblank
+ * @get_align: Get the alignment requirement of CRTC device
+ * @get_dma_mask: Get the dma mask of CRTC device
+ * @get_max_width: Get the maximum supported width
+ * @get_max_height: Get the maximum supported height
+ * @get_format: Get the current format of CRTC device
+ */
+struct xlnx_crtc {
+ struct drm_crtc crtc;
+ struct list_head list;
+ int (*enable_vblank)(struct xlnx_crtc *crtc);
+ void (*disable_vblank)(struct xlnx_crtc *crtc);
+ unsigned int (*get_align)(struct xlnx_crtc *crtc);
+ u64 (*get_dma_mask)(struct xlnx_crtc *crtc);
+ int (*get_max_width)(struct xlnx_crtc *crtc);
+ int (*get_max_height)(struct xlnx_crtc *crtc);
+ uint32_t (*get_format)(struct xlnx_crtc *crtc);
+};
+
+/*
+ * Helper functions: used within Xlnx DRM
+ */
+
+struct xlnx_crtc_helper;
+
+int xlnx_crtc_helper_enable_vblank(struct xlnx_crtc_helper *helper,
+ unsigned int crtc_id);
+void xlnx_crtc_helper_disable_vblank(struct xlnx_crtc_helper *helper,
+ unsigned int crtc_id);
+unsigned int xlnx_crtc_helper_get_align(struct xlnx_crtc_helper *helper);
+u64 xlnx_crtc_helper_get_dma_mask(struct xlnx_crtc_helper *helper);
+int xlnx_crtc_helper_get_max_width(struct xlnx_crtc_helper *helper);
+int xlnx_crtc_helper_get_max_height(struct xlnx_crtc_helper *helper);
+uint32_t xlnx_crtc_helper_get_format(struct xlnx_crtc_helper *helper);
+
+struct xlnx_crtc_helper *xlnx_crtc_helper_init(struct drm_device *drm);
+void xlnx_crtc_helper_fini(struct drm_device *drm,
+ struct xlnx_crtc_helper *helper);
+
+/*
+ * CRTC registration: used by other sub-driver modules
+ */
+
+static inline struct xlnx_crtc *to_xlnx_crtc(struct drm_crtc *crtc)
+{
+ return container_of(crtc, struct xlnx_crtc, crtc);
+}
+
+void xlnx_crtc_register(struct drm_device *drm, struct xlnx_crtc *crtc);
+void xlnx_crtc_unregister(struct drm_device *drm, struct xlnx_crtc *crtc);
+
+#endif /* _XLNX_CRTC_H_ */
diff --git a/drivers/gpu/drm/xlnx/xlnx_drv.c b/drivers/gpu/drm/xlnx/xlnx_drv.c
new file mode 100644
index 0000000..a350492
--- /dev/null
+++ b/drivers/gpu/drm/xlnx/xlnx_drv.c
@@ -0,0 +1,447 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx DRM KMS Driver
+ *
+ * Copyright (C) 2013 - 2018 Xilinx, Inc.
+ *
+ * Author: Hyun Woo Kwon <hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <drm/drmP.h>
+#include <drm/drm_atomic.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_fb_helper.h>
+#include <drm/drm_gem_cma_helper.h>
+#include <drm/drm_of.h>
+
+#include <linux/component.h>
+#include <linux/device.h>
+#include <linux/dma-buf.h>
+#include <linux/module.h>
+#include <linux/of_graph.h>
+#include <linux/platform_device.h>
+#include <linux/reservation.h>
+
+#include "xlnx_crtc.h"
+#include "xlnx_fb.h"
+#include "xlnx_gem.h"
+
+#define DRIVER_NAME "xlnx"
+#define DRIVER_DESC "Xilinx DRM KMS Driver"
+#define DRIVER_DATE "20130509"
+#define DRIVER_MAJOR 1
+#define DRIVER_MINOR 0
+
+static uint xlnx_fbdev_vres = 2;
+module_param_named(fbdev_vres, xlnx_fbdev_vres, uint, 0444);
+MODULE_PARM_DESC(fbdev_vres,
+ "fbdev virtual resolution multiplier for fb (default: 2)");
+
+/**
+ * struct xlnx_drm - Xilinx DRM private data
+ * @drm: DRM core
+ * @crtc: Xilinx DRM CRTC helper
+ * @fb: DRM fb helper
+ * @pdev: platform device
+ * @suspend_state: atomic state for suspend / resume
+ */
+struct xlnx_drm {
+ struct drm_device *drm;
+ struct xlnx_crtc_helper *crtc;
+ struct drm_fb_helper *fb;
+ struct platform_device *pdev;
+ struct drm_atomic_state *suspend_state;
+};
+
+/**
+ * xlnx_get_crtc_helper - Return the crtc helper instance
+ * @drm: DRM device
+ *
+ * Return: the crtc helper instance
+ */
+struct xlnx_crtc_helper *xlnx_get_crtc_helper(struct drm_device *drm)
+{
+ struct xlnx_drm *xlnx_drm = drm->dev_private;
+
+ return xlnx_drm->crtc;
+}
+
+/**
+ * xlnx_get_align - Return the align requirement through CRTC helper
+ * @drm: DRM device
+ *
+ * Return: the alignment requirement
+ */
+unsigned int xlnx_get_align(struct drm_device *drm)
+{
+ struct xlnx_drm *xlnx_drm = drm->dev_private;
+
+ return xlnx_crtc_helper_get_align(xlnx_drm->crtc);
+}
+
+/**
+ * xlnx_get_format - Return the current format of CRTC
+ * @drm: DRM device
+ *
+ * Return: the current CRTC format
+ */
+uint32_t xlnx_get_format(struct drm_device *drm)
+{
+ struct xlnx_drm *xlnx_drm = drm->dev_private;
+
+ return xlnx_crtc_helper_get_format(xlnx_drm->crtc);
+}
+
+static void xlnx_output_poll_changed(struct drm_device *drm)
+{
+ struct xlnx_drm *xlnx_drm = drm->dev_private;
+
+ if (xlnx_drm->fb)
+ drm_fb_helper_hotplug_event(xlnx_drm->fb);
+}
+
+static const struct drm_mode_config_funcs xlnx_mode_config_funcs = {
+ .fb_create = xlnx_fb_create,
+ .output_poll_changed = xlnx_output_poll_changed,
+ .atomic_check = drm_atomic_helper_check,
+ .atomic_commit = drm_atomic_helper_commit,
+};
+
+static int xlnx_enable_vblank(struct drm_device *drm, unsigned int crtc)
+{
+ struct xlnx_drm *xlnx_drm = drm->dev_private;
+
+ return xlnx_crtc_helper_enable_vblank(xlnx_drm->crtc, crtc);
+}
+
+static void xlnx_disable_vblank(struct drm_device *drm, unsigned int crtc)
+{
+ struct xlnx_drm *xlnx_drm = drm->dev_private;
+
+ xlnx_crtc_helper_disable_vblank(xlnx_drm->crtc, crtc);
+}
+
+static void xlnx_mode_config_init(struct drm_device *drm)
+{
+ struct xlnx_drm *xlnx_drm = drm->dev_private;
+ struct xlnx_crtc_helper *crtc = xlnx_drm->crtc;
+
+ drm->mode_config.min_width = 0;
+ drm->mode_config.min_height = 0;
+ drm->mode_config.max_width = xlnx_crtc_helper_get_max_width(crtc);
+ drm->mode_config.max_height = xlnx_crtc_helper_get_max_height(crtc);
+}
+
+static void xlnx_lastclose(struct drm_device *drm)
+{
+ struct xlnx_drm *xlnx_drm = drm->dev_private;
+
+ if (xlnx_drm->fb)
+ drm_fb_helper_restore_fbdev_mode_unlocked(xlnx_drm->fb);
+}
+
+static const struct file_operations xlnx_fops = {
+ .owner = THIS_MODULE,
+ .open = drm_open,
+ .release = drm_release,
+ .unlocked_ioctl = drm_ioctl,
+ .mmap = drm_gem_cma_mmap,
+ .poll = drm_poll,
+ .read = drm_read,
+#ifdef CONFIG_COMPAT
+ .compat_ioctl = drm_compat_ioctl,
+#endif
+ .llseek = noop_llseek,
+};
+
+static struct drm_driver xlnx_drm_driver = {
+ .driver_features = DRIVER_MODESET | DRIVER_GEM |
+ DRIVER_ATOMIC | DRIVER_PRIME,
+ .lastclose = xlnx_lastclose,
+
+ .enable_vblank = xlnx_enable_vblank,
+ .disable_vblank = xlnx_disable_vblank,
+
+ .prime_handle_to_fd = drm_gem_prime_handle_to_fd,
+ .prime_fd_to_handle = drm_gem_prime_fd_to_handle,
+ .gem_prime_export = drm_gem_prime_export,
+ .gem_prime_import = drm_gem_prime_import,
+ .gem_prime_get_sg_table = drm_gem_cma_prime_get_sg_table,
+ .gem_prime_import_sg_table = drm_gem_cma_prime_import_sg_table,
+ .gem_prime_vmap = drm_gem_cma_prime_vmap,
+ .gem_prime_vunmap = drm_gem_cma_prime_vunmap,
+ .gem_prime_mmap = drm_gem_cma_prime_mmap,
+ .gem_free_object = drm_gem_cma_free_object,
+ .gem_vm_ops = &drm_gem_cma_vm_ops,
+ .dumb_create = xlnx_gem_cma_dumb_create,
+ .dumb_destroy = drm_gem_dumb_destroy,
+
+ .fops = &xlnx_fops,
+
+ .name = DRIVER_NAME,
+ .desc = DRIVER_DESC,
+ .date = DRIVER_DATE,
+ .major = DRIVER_MAJOR,
+ .minor = DRIVER_MINOR,
+};
+
+static int xlnx_bind(struct device *dev)
+{
+ struct xlnx_drm *xlnx_drm;
+ struct drm_device *drm;
+ const struct drm_format_info *info;
+ struct platform_device *pdev = to_platform_device(dev);
+ int ret;
+ u32 format;
+
+ drm = drm_dev_alloc(&xlnx_drm_driver, &pdev->dev);
+ if (IS_ERR(drm))
+ return PTR_ERR(drm);
+
+ xlnx_drm = devm_kzalloc(drm->dev, sizeof(*xlnx_drm), GFP_KERNEL);
+ if (!xlnx_drm) {
+ ret = -ENOMEM;
+ goto err_drm;
+ }
+
+ drm_mode_config_init(drm);
+ drm->mode_config.funcs = &xlnx_mode_config_funcs;
+
+ ret = drm_vblank_init(drm, 1);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to initialize vblank\n");
+ goto err_xlnx_drm;
+ }
+
+ drm->irq_enabled = 1;
+ drm->dev_private = xlnx_drm;
+ xlnx_drm->drm = drm;
+ drm_kms_helper_poll_init(drm);
+ platform_set_drvdata(pdev, xlnx_drm);
+
+ xlnx_drm->crtc = xlnx_crtc_helper_init(drm);
+ if (IS_ERR(xlnx_drm->crtc)) {
+ ret = PTR_ERR(xlnx_drm->crtc);
+ goto err_xlnx_drm;
+ }
+
+ ret = component_bind_all(drm->dev, drm);
+ if (ret)
+ goto err_crtc;
+
+ xlnx_mode_config_init(drm);
+ drm_mode_config_reset(drm);
+ dma_set_mask(drm->dev, xlnx_crtc_helper_get_dma_mask(xlnx_drm->crtc));
+
+ format = xlnx_crtc_helper_get_format(xlnx_drm->crtc);
+ info = drm_format_info(format);
+ if (info && info->depth && info->cpp[0]) {
+ unsigned int align;
+
+ align = xlnx_crtc_helper_get_align(xlnx_drm->crtc);
+ xlnx_drm->fb = xlnx_fb_init(drm, info->cpp[0] * 8, 1, align,
+ xlnx_fbdev_vres);
+ if (IS_ERR(xlnx_drm->fb)) {
+ dev_err(&pdev->dev,
+ "failed to initialize drm fb\n");
+ xlnx_drm->fb = NULL;
+ }
+ } else {
+ /* fbdev emulation is optional */
+ dev_info(&pdev->dev, "fbdev is not initialized\n");
+ }
+
+ ret = drm_dev_register(drm, 0);
+ if (ret < 0)
+ goto err_fb;
+
+ return 0;
+
+err_fb:
+ if (xlnx_drm->fb)
+ xlnx_fb_fini(xlnx_drm->fb);
+ component_unbind_all(drm->dev, drm);
+err_crtc:
+ xlnx_crtc_helper_fini(drm, xlnx_drm->crtc);
+err_xlnx_drm:
+ drm_mode_config_cleanup(drm);
+err_drm:
+ drm_dev_unref(drm);
+ return ret;
+}
+
+static void xlnx_unbind(struct device *dev)
+{
+ struct xlnx_drm *xlnx_drm = dev_get_drvdata(dev);
+ struct drm_device *drm = xlnx_drm->drm;
+
+ drm_dev_unregister(drm);
+ if (xlnx_drm->fb)
+ xlnx_fb_fini(xlnx_drm->fb);
+ component_unbind_all(drm->dev, drm);
+ xlnx_crtc_helper_fini(drm, xlnx_drm->crtc);
+ drm_kms_helper_poll_fini(drm);
+ drm_mode_config_cleanup(drm);
+ drm_dev_unref(drm);
+}
+
+static const struct component_master_ops xlnx_master_ops = {
+ .bind = xlnx_bind,
+ .unbind = xlnx_unbind,
+};
+
+static int xlnx_of_component_probe(struct device *dev,
+ int (*compare_of)(struct device *, void *),
+ const struct component_master_ops *m_ops)
+{
+ struct device_node *ep, *port, *remote, *parent;
+ struct component_match *match = NULL;
+ int i;
+
+ if (!dev->of_node)
+ return -EINVAL;
+
+ for (i = 0; ; i++) {
+ port = of_parse_phandle(dev->of_node, "ports", i);
+ if (!port)
+ break;
+
+ parent = of_graph_get_port_parent(port);
+ if (!of_device_is_available(parent)) {
+ of_node_put(port);
+ continue;
+ }
+
+ component_match_add(dev, &match, compare_of, parent);
+ of_node_put(parent);
+ of_node_put(port);
+ }
+
+ if (i == 0) {
+ dev_err(dev, "missing 'ports' property\n");
+ return -ENODEV;
+ }
+
+ if (!match) {
+ dev_err(dev, "no available port\n");
+ return -ENODEV;
+ }
+
+ for (i = 0; ; i++) {
+ port = of_parse_phandle(dev->of_node, "ports", i);
+ if (!port)
+ break;
+
+ parent = of_graph_get_port_parent(port);
+ if (!of_device_is_available(parent)) {
+ of_node_put(port);
+ continue;
+ }
+
+ for_each_child_of_node(port, ep) {
+ remote = of_graph_get_remote_port_parent(ep);
+ if (!remote || !of_device_is_available(remote)) {
+ of_node_put(remote);
+ continue;
+ } else if (!of_device_is_available(remote->parent)) {
+ dev_warn(dev, "parent dev of %s unavailable\n",
+ remote->full_name);
+ of_node_put(remote);
+ continue;
+ }
+ component_match_add(dev, &match, compare_of, remote);
+ of_node_put(remote);
+ }
+ of_node_put(port);
+ }
+
+ return component_master_add_with_match(dev, m_ops, match);
+}
+
+static int xlnx_compare_of(struct device *dev, void *data)
+{
+ return dev->of_node == data;
+}
+
+static int xlnx_platform_probe(struct platform_device *pdev)
+{
+ return xlnx_of_component_probe(&pdev->dev, xlnx_compare_of,
+ &xlnx_master_ops);
+}
+
+static int xlnx_platform_remove(struct platform_device *pdev)
+{
+ component_master_del(&pdev->dev, &xlnx_master_ops);
+ return 0;
+}
+
+static void xlnx_platform_shutdown(struct platform_device *pdev)
+{
+ struct xlnx_drm *xlnx_drm = platform_get_drvdata(pdev);
+
+ drm_put_dev(xlnx_drm->drm);
+}
+
+static int __maybe_unused xlnx_pm_suspend(struct device *dev)
+{
+ struct xlnx_drm *xlnx_drm = dev_get_drvdata(dev);
+ struct drm_device *drm = xlnx_drm->drm;
+
+ drm_kms_helper_poll_disable(drm);
+
+ xlnx_drm->suspend_state = drm_atomic_helper_suspend(drm);
+ if (IS_ERR(xlnx_drm->suspend_state)) {
+ drm_kms_helper_poll_enable(drm);
+ return PTR_ERR(xlnx_drm->suspend_state);
+ }
+
+ return 0;
+}
+
+static int __maybe_unused xlnx_pm_resume(struct device *dev)
+{
+ struct xlnx_drm *xlnx_drm = dev_get_drvdata(dev);
+ struct drm_device *drm = xlnx_drm->drm;
+
+ drm_atomic_helper_resume(drm, xlnx_drm->suspend_state);
+ drm_kms_helper_poll_enable(drm);
+
+ return 0;
+}
+
+static const struct dev_pm_ops xlnx_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(xlnx_pm_suspend, xlnx_pm_resume)
+};
+
+static const struct of_device_id xlnx_of_match[] = {
+ { .compatible = "xlnx,display", },
+ { /* end of table */ },
+};
+MODULE_DEVICE_TABLE(of, xlnx_of_match);
+
+static struct platform_driver xlnx_driver = {
+ .probe = xlnx_platform_probe,
+ .remove = xlnx_platform_remove,
+ .shutdown = xlnx_platform_shutdown,
+ .driver = {
+ .name = "xlnx-drm",
+ .pm = &xlnx_pm_ops,
+ .of_match_table = xlnx_of_match,
+ },
+};
+
+module_platform_driver(xlnx_driver);
+
+MODULE_AUTHOR("Xilinx, Inc.");
+MODULE_DESCRIPTION("Xilinx DRM KMS Driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/gpu/drm/xlnx/xlnx_drv.h b/drivers/gpu/drm/xlnx/xlnx_drv.h
new file mode 100644
index 0000000..8c320fd
--- /dev/null
+++ b/drivers/gpu/drm/xlnx/xlnx_drv.h
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx DRM KMS Header for Xilinx
+ *
+ * Copyright (C) 2013 - 2018 Xilinx, Inc.
+ *
+ * Author: Hyun Woo Kwon <hyunk-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _XLNX_DRV_H_
+#define _XLNX_DRV_H_
+
+struct drm_device;
+struct xlnx_crtc_helper;
+
+uint32_t xlnx_get_format(struct drm_device *drm);
+unsigned int xlnx_get_align(struct drm_device *drm);
+struct xlnx_crtc_helper *xlnx_get_crtc_helper(struct drm_device *drm);
+struct xlnx_bridge_helper *xlnx_get_bridge_helper(struct drm_device *drm);
+
+#endif /* _XLNX_DRV_H_ */
diff --git a/drivers/gpu/drm/xlnx/xlnx_fb.c b/drivers/gpu/drm/xlnx/xlnx_fb.c
new file mode 100644
index 0000000..e72087d
--- /dev/null
+++ b/drivers/gpu/drm/xlnx/xlnx_fb.c
@@ -0,0 +1,298 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx DRM KMS Framebuffer helper
+ *
+ * Copyright (C) 2015 - 2018 Xilinx, Inc.
+ *
+ * Author: Hyun Woo Kwon <hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
+ *
+ * Based on drm_fb_cma_helper.c
+ *
+ * Copyright (C) 2012 Analog Device Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <drm/drmP.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_fb_helper.h>
+#include <drm/drm_gem_cma_helper.h>
+#include <drm/drm_gem_framebuffer_helper.h>
+
+#include "xlnx_drv.h"
+#include "xlnx_fb.h"
+
+#define XLNX_MAX_PLANES 4
+
+struct xlnx_fbdev {
+ struct drm_fb_helper fb_helper;
+ struct drm_framebuffer *fb;
+ unsigned int align;
+ unsigned int vres_mult;
+};
+
+static inline struct xlnx_fbdev *to_fbdev(struct drm_fb_helper *fb_helper)
+{
+ return container_of(fb_helper, struct xlnx_fbdev, fb_helper);
+}
+
+static struct drm_framebuffer_funcs xlnx_fb_funcs = {
+ .destroy = drm_gem_fb_destroy,
+ .create_handle = drm_gem_fb_create_handle,
+};
+
+static int
+xlnx_fb_ioctl(struct fb_info *info, unsigned int cmd, unsigned long arg)
+{
+ struct drm_fb_helper *fb_helper = info->par;
+ unsigned int i;
+ int ret = 0;
+
+ switch (cmd) {
+ case FBIO_WAITFORVSYNC:
+ for (i = 0; i < fb_helper->crtc_count; i++) {
+ struct drm_mode_set *mode_set;
+ struct drm_crtc *crtc;
+
+ mode_set = &fb_helper->crtc_info[i].mode_set;
+ crtc = mode_set->crtc;
+ ret = drm_crtc_vblank_get(crtc);
+ if (!ret) {
+ drm_crtc_wait_one_vblank(crtc);
+ drm_crtc_vblank_put(crtc);
+ }
+ }
+ return ret;
+ default:
+ return -ENOTTY;
+ }
+
+ return 0;
+}
+
+static struct fb_ops xlnx_fbdev_ops = {
+ .owner = THIS_MODULE,
+ .fb_fillrect = sys_fillrect,
+ .fb_copyarea = sys_copyarea,
+ .fb_imageblit = sys_imageblit,
+ .fb_check_var = drm_fb_helper_check_var,
+ .fb_set_par = drm_fb_helper_set_par,
+ .fb_blank = drm_fb_helper_blank,
+ .fb_pan_display = drm_fb_helper_pan_display,
+ .fb_setcmap = drm_fb_helper_setcmap,
+ .fb_ioctl = xlnx_fb_ioctl,
+};
+
+/**
+ * xlnx_fbdev_create - Create the fbdev with a framebuffer
+ * @fb_helper: fb helper structure
+ * @size: framebuffer size info
+ *
+ * This function is based on drm_fbdev_cma_create().
+ *
+ * Return: 0 if successful, or the error code.
+ */
+static int xlnx_fbdev_create(struct drm_fb_helper *fb_helper,
+ struct drm_fb_helper_surface_size *size)
+{
+ struct xlnx_fbdev *fbdev = to_fbdev(fb_helper);
+ struct drm_device *drm = fb_helper->dev;
+ struct drm_gem_cma_object *obj;
+ struct drm_framebuffer *fb;
+ unsigned int bytes_per_pixel;
+ unsigned long offset;
+ struct fb_info *fbi;
+ size_t bytes;
+ int ret;
+
+ dev_dbg(drm->dev, "surface width(%d), height(%d) and bpp(%d)\n",
+ size->surface_width, size->surface_height, size->surface_bpp);
+
+ size->surface_height *= fbdev->vres_mult;
+ bytes_per_pixel = DIV_ROUND_UP(size->surface_bpp, 8);
+ bytes = ALIGN(size->surface_width * bytes_per_pixel, fbdev->align);
+ bytes *= size->surface_height;
+
+ obj = drm_gem_cma_create(drm, bytes);
+ if (IS_ERR(obj))
+ return PTR_ERR(obj);
+
+ fbi = framebuffer_alloc(0, drm->dev);
+ if (!fbi) {
+ dev_err(drm->dev, "Failed to allocate framebuffer info.\n");
+ ret = -ENOMEM;
+ goto err_drm_gem_cma_free_object;
+ }
+
+ fbdev->fb = drm_gem_fbdev_fb_create(drm, size, fbdev->align, &obj->base,
+ &xlnx_fb_funcs);
+ if (IS_ERR(fbdev->fb)) {
+ dev_err(drm->dev, "Failed to allocate DRM framebuffer.\n");
+ ret = PTR_ERR(fbdev->fb);
+ goto err_framebuffer_release;
+ }
+
+ fb = fbdev->fb;
+ fb_helper->fb = fb;
+ fb_helper->fbdev = fbi;
+ fbi->par = fb_helper;
+ fbi->flags = FBINFO_FLAG_DEFAULT;
+ fbi->fbops = &xlnx_fbdev_ops;
+
+ ret = fb_alloc_cmap(&fbi->cmap, 256, 0);
+ if (ret) {
+ dev_err(drm->dev, "Failed to allocate color map.\n");
+ goto err_fb_destroy;
+ }
+
+ drm_fb_helper_fill_fix(fbi, fb->pitches[0], fb->format->depth);
+ drm_fb_helper_fill_var(fbi, fb_helper, fb->width, fb->height);
+ fbi->var.yres = fb->height / fbdev->vres_mult;
+
+ offset = fbi->var.xoffset * bytes_per_pixel;
+ offset += fbi->var.yoffset * fb->pitches[0];
+
+ drm->mode_config.fb_base = (resource_size_t)obj->paddr;
+ fbi->screen_base = (char __iomem *)(obj->vaddr + offset);
+ fbi->fix.smem_start = (unsigned long)(obj->paddr + offset);
+ fbi->screen_size = bytes;
+ fbi->fix.smem_len = bytes;
+
+ return 0;
+
+err_fb_destroy:
+ drm_framebuffer_unregister_private(fb);
+ drm_gem_fb_destroy(fb);
+err_framebuffer_release:
+ framebuffer_release(fbi);
+err_drm_gem_cma_free_object:
+ drm_gem_cma_free_object(&obj->base);
+ return ret;
+}
+
+static struct drm_fb_helper_funcs xlnx_fb_helper_funcs = {
+ .fb_probe = xlnx_fbdev_create,
+};
+
+/**
+ * xlnx_fb_init - Allocate and initializes the Xilinx framebuffer
+ * @drm: DRM device
+ * @preferred_bpp: preferred bits per pixel for the device
+ * @max_conn_count: maximum number of connectors
+ * @align: alignment value for pitch
+ * @vres_mult: multiplier for virtual resolution
+ *
+ * This function is based on drm_fbdev_cma_init().
+ *
+ * Return: a newly allocated drm_fb_helper struct or a ERR_PTR.
+ */
+struct drm_fb_helper *
+xlnx_fb_init(struct drm_device *drm, int preferred_bpp,
+ unsigned int max_conn_count, unsigned int align,
+ unsigned int vres_mult)
+{
+ struct xlnx_fbdev *fbdev;
+ struct drm_fb_helper *fb_helper;
+ int ret;
+
+ fbdev = kzalloc(sizeof(*fbdev), GFP_KERNEL);
+ if (!fbdev)
+ return ERR_PTR(-ENOMEM);
+
+ fbdev->vres_mult = vres_mult;
+ fbdev->align = align;
+ fb_helper = &fbdev->fb_helper;
+ drm_fb_helper_prepare(drm, fb_helper, &xlnx_fb_helper_funcs);
+
+ ret = drm_fb_helper_init(drm, fb_helper, max_conn_count);
+ if (ret < 0) {
+ dev_err(drm->dev, "Failed to initialize drm fb helper.\n");
+ goto err_free;
+ }
+
+ ret = drm_fb_helper_single_add_all_connectors(fb_helper);
+ if (ret < 0) {
+ dev_err(drm->dev, "Failed to add connectors.\n");
+ goto err_drm_fb_helper_fini;
+ }
+
+ ret = drm_fb_helper_initial_config(fb_helper, preferred_bpp);
+ if (ret < 0) {
+ dev_err(drm->dev, "Failed to set initial hw configuration.\n");
+ goto err_drm_fb_helper_fini;
+ }
+
+ return fb_helper;
+
+err_drm_fb_helper_fini:
+ drm_fb_helper_fini(fb_helper);
+err_free:
+ kfree(fbdev);
+ return ERR_PTR(ret);
+}
+
+/**
+ * xlnx_fbdev_defio_fini - Free the defio fb
+ * @fbi: fb_info struct
+ *
+ * This function is based on drm_fbdev_cma_defio_fini().
+ */
+static void xlnx_fbdev_defio_fini(struct fb_info *fbi)
+{
+ if (!fbi->fbdefio)
+ return;
+
+ fb_deferred_io_cleanup(fbi);
+ kfree(fbi->fbdefio);
+ kfree(fbi->fbops);
+}
+
+/**
+ * xlnx_fbdev_fini - Free the Xilinx framebuffer
+ * @fb_helper: drm_fb_helper struct
+ *
+ * This function is based on drm_fbdev_cma_fini().
+ */
+void xlnx_fb_fini(struct drm_fb_helper *fb_helper)
+{
+ struct xlnx_fbdev *fbdev = to_fbdev(fb_helper);
+
+ drm_fb_helper_unregister_fbi(&fbdev->fb_helper);
+ if (fbdev->fb_helper.fbdev)
+ xlnx_fbdev_defio_fini(fbdev->fb_helper.fbdev);
+
+ if (fbdev->fb_helper.fb)
+ drm_framebuffer_remove(fbdev->fb_helper.fb);
+
+ drm_fb_helper_fini(&fbdev->fb_helper);
+ kfree(fbdev);
+}
+
+/**
+ * xlnx_fb_create - (struct drm_mode_config_funcs *)->fb_create callback
+ * @drm: DRM device
+ * @file_priv: drm file private data
+ * @mode_cmd: mode command for fb creation
+ *
+ * This functions creates a drm_framebuffer with xlnx_fb_funcs for given mode
+ * @mode_cmd. This functions is intended to be used for the fb_create callback
+ * function of drm_mode_config_funcs.
+ *
+ * Return: a drm_framebuffer object if successful, or
+ * ERR_PTR from drm_gem_fb_create_with_funcs().
+ */
+struct drm_framebuffer *
+xlnx_fb_create(struct drm_device *drm, struct drm_file *file_priv,
+ const struct drm_mode_fb_cmd2 *mode_cmd)
+{
+ return drm_gem_fb_create_with_funcs(drm, file_priv, mode_cmd,
+ &xlnx_fb_funcs);
+}
diff --git a/drivers/gpu/drm/xlnx/xlnx_fb.h b/drivers/gpu/drm/xlnx/xlnx_fb.h
new file mode 100644
index 0000000..6efc985
--- /dev/null
+++ b/drivers/gpu/drm/xlnx/xlnx_fb.h
@@ -0,0 +1,33 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx DRM KMS Framebuffer helper header
+ *
+ * Copyright (C) 2015 - 2018 Xilinx, Inc.
+ *
+ * Author: Hyun Woo Kwon <hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _XLNX_FB_H_
+#define _XLNX_FB_H_
+
+struct drm_fb_helper;
+
+struct drm_framebuffer *
+xlnx_fb_create(struct drm_device *drm, struct drm_file *file_priv,
+ const struct drm_mode_fb_cmd2 *mode_cmd);
+struct drm_fb_helper *
+xlnx_fb_init(struct drm_device *drm, int preferred_bpp,
+ unsigned int max_conn_count, unsigned int align,
+ unsigned int vres_mult);
+void xlnx_fb_fini(struct drm_fb_helper *fb_helper);
+
+#endif /* _XLNX_FB_H_ */
diff --git a/drivers/gpu/drm/xlnx/xlnx_gem.c b/drivers/gpu/drm/xlnx/xlnx_gem.c
new file mode 100644
index 0000000..4a5d533
--- /dev/null
+++ b/drivers/gpu/drm/xlnx/xlnx_gem.c
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx DRM KMS GEM helper
+ *
+ * Copyright (C) 2015 - 2018 Xilinx, Inc.
+ *
+ * Author: Hyun Woo Kwon <hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <drm/drmP.h>
+#include <drm/drm_gem_cma_helper.h>
+
+#include "xlnx_drv.h"
+#include "xlnx_gem.h"
+
+/*
+ * xlnx_gem_cma_dumb_create - (struct drm_driver)->dumb_create callback
+ * @file_priv: drm_file object
+ * @drm: DRM object
+ * @args: info for dumb scanout buffer creation
+ *
+ * This function is for dumb_create callback of drm_driver struct. Simply
+ * it wraps around drm_gem_cma_dumb_create() and sets the pitch value
+ * by retrieving the value from the device.
+ *
+ * Return: The return value from drm_gem_cma_dumb_create()
+ */
+int xlnx_gem_cma_dumb_create(struct drm_file *file_priv, struct drm_device *drm,
+ struct drm_mode_create_dumb *args)
+{
+ int pitch = DIV_ROUND_UP(args->width * args->bpp, 8);
+ unsigned int align = xlnx_get_align(drm);
+
+ if (!args->pitch || !IS_ALIGNED(args->pitch, align))
+ args->pitch = ALIGN(pitch, align);
+
+ return drm_gem_cma_dumb_create_internal(file_priv, drm, args);
+}
diff --git a/drivers/gpu/drm/xlnx/xlnx_gem.h b/drivers/gpu/drm/xlnx/xlnx_gem.h
new file mode 100644
index 0000000..f380de9
--- /dev/null
+++ b/drivers/gpu/drm/xlnx/xlnx_gem.h
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx DRM KMS GEM helper header
+ *
+ * Copyright (C) 2015 - 2018 Xilinx, Inc.
+ *
+ * Author: Hyun Woo Kwon <hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _XLNX_GEM_H_
+#define _XLNX_GEM_H_
+
+int xlnx_gem_cma_dumb_create(struct drm_file *file_priv,
+ struct drm_device *drm,
+ struct drm_mode_create_dumb *args);
+
+#endif /* _XLNX_GEM_H_ */
--
2.7.4
This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH v3 3/8] dt-bindings: display: xlnx: Add ZynqMP DP subsystem bindings
[not found] ` <1516067831-11382-1-git-send-email-hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
2018-01-16 1:57 ` [PATCH v3 2/8] drm: xlnx: Xilinx DRM KMS driver Hyun Kwon
@ 2018-01-16 1:57 ` Hyun Kwon
[not found] ` <1516067831-11382-3-git-send-email-hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
2018-01-16 1:57 ` [PATCH v3 4/8] drm: xlnx: DRM KMS driver for Xilinx ZynqMP DP subsystem display Hyun Kwon
` (2 subsequent siblings)
4 siblings, 1 reply; 17+ messages in thread
From: Hyun Kwon @ 2018-01-16 1:57 UTC (permalink / raw)
To: dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW,
devicetree-u79uwXL29TY76Z2rM5mHXA
Cc: Michal Simek, Rob Herring, Daniel Vetter, Laurent Pinchart, Hyun Kwon
This add a dt binding for ZynqMP DP subsystem.
Signed-off-by: Hyun Kwon <hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
---
v2
- Group multiple ports under 'ports'
- Replace linux specific terms with generic hardware descriptions
---
---
.../bindings/display/xlnx/xlnx,zynqmp-dpsub.txt | 98 ++++++++++++++++++++++
1 file changed, 98 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.txt
diff --git a/Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.txt b/Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.txt
new file mode 100644
index 0000000..dbcbde5
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.txt
@@ -0,0 +1,98 @@
+Xilinx ZynqMP DisplayPort subsystem
+-----------------------------------
+
+Required properties:
+
+- compatible: Must be "xlnx,zynqmp-dpsub-1.7".
+
+- reg: Physical base address and length of the registers set for the device.
+- reg-names: Must be "dp", "blend", "av_buf", and "aud" to map logical register
+ partitions.
+
+- interrupts: Interrupt number.
+- interrupts-parent: phandle for interrupt controller.
+
+- clocks: phandles for axi, audio, non-live video, and live video clocks.
+ axi clock is required. Audio clock is optional. If not present, audio will
+ be disabled. One of non-live or live video clock should be present.
+- clock-names: The identification strings are required. "aclk" for axi clock.
+ "dp_aud_clk" for audio clock. "dp_vtc_pixel_clk_in" for non-live video clock.
+ "dp_live_video_in_clk" for live video clock (clock from programmable logic).
+
+- phys: phandles for phy specifier.
+- phy-names: The identifier strings. "dp-phy" followed by index.
+
+- power-domains: phandle for the corresponding power domain
+
+- ports: There are 2 logical blocks in the IP: display controller and
+ DisplayPort encoder. Each block can be used / connected independently with
+ external device, hence ports for each block are required using DT bindings
+ defined in Documentation/devicetree/bindings/graph.txt. Refer to
+ ./xlnx,display.txt for how topology for entire pipeline is described.
+
+- vid-layer, gfx-layer: Required to represent available layers
+
+Required layer properties
+
+- dmas: phandles for DMA channels as defined in
+ Documentation/devicetree/bindings/dma/dma.txt.
+- dma-names: The identifier strings are required. "graphics0" for graphics
+ layer. "video" followed by index for video layer
+
+Optional child node
+
+- The driver populates any child device node in this node. This can be used,
+ for example, to populate the sound device from the DisplayPort subsystem
+ driver.
+
+Example:
+ zynqmp_dpsub: zynqmp_dpsub@fd4a0000 {
+ compatible = "xlnx,zynqmp-dpsub-1.7";
+ reg = <0x0 0xfd4a0000 0x0 0x1000>,
+ <0x0 0xfd4aa000 0x0 0x1000>,
+ <0x0 0xfd4ab000 0x0 0x1000>,
+ <0x0 0xfd4ac000 0x0 0x1000>;
+ reg-names = "dp", "blend", "av_buf", "aud";
+ interrupts = <0 119 4>;
+ interrupt-parent = <&gic>;
+
+ clock-names = "dp_apb_clk", "dp_aud_clk", "dp_live_video_in_clk";
+ clocks = <&dp_aclk>, <&clkc 17>, <&si570_1>;
+
+ phys = <&lane1>, <&lane0>;
+ phy-names = "dp-phy0", "dp-phy1";
+
+ power-domains = <&pd_dp>;
+
+ vid-layer {
+ dma-names = "vid0", "vid1", "vid2";
+ dmas = <&xlnx_dpdma 0>,
+ <&xlnx_dpdma 1>,
+ <&xlnx_dpdma 2>;
+ };
+
+ gfx-layer {
+ dma-names = "gfx0";
+ dmas = <&xlnx_dpdma 3>;
+ };
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ display_port: port@0 {
+ reg = <0>;
+ display_port: endpoint {
+ remote-endpoint = <&dp_port>;
+ };
+ };
+ port@1 {
+ reg = <1>;
+ dp_port: endpoint {
+ remote-endpoint = <&display_port>;
+ };
+ };
+ }
+ };
+};
+
--
2.7.4
This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH v3 4/8] drm: xlnx: DRM KMS driver for Xilinx ZynqMP DP subsystem display
[not found] ` <1516067831-11382-1-git-send-email-hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
2018-01-16 1:57 ` [PATCH v3 2/8] drm: xlnx: Xilinx DRM KMS driver Hyun Kwon
2018-01-16 1:57 ` [PATCH v3 3/8] dt-bindings: display: xlnx: Add ZynqMP DP subsystem bindings Hyun Kwon
@ 2018-01-16 1:57 ` Hyun Kwon
2018-01-16 1:57 ` [PATCH v3 5/8] drm: xlnx: DRM KMS driver for Xilinx ZynqMP DisplayPort Hyun Kwon
2018-01-16 1:57 ` [PATCH v3 6/8] drm: xlnx: ZynqMP DP subsystem DRM KMS driver Hyun Kwon
4 siblings, 0 replies; 17+ messages in thread
From: Hyun Kwon @ 2018-01-16 1:57 UTC (permalink / raw)
To: dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW,
devicetree-u79uwXL29TY76Z2rM5mHXA
Cc: Michal Simek, Rob Herring, Daniel Vetter, Laurent Pinchart, Hyun Kwon
Xilinx ZynqMP has a hardened display pipeline. The pipeline can
be logically partitioned into 2 parts: display controller and
DisplayPort encoder / transmitter. This driver handles the display
controller part of the pipeline that handles buffer management and
blending.
Signed-off-by: Hyun Kwon <hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
---
v3
- Fix a small typo
v2
- Use drm_fb_cma_get_gem_addr()
- Use drm_crtc_arm_vblank_event()
- Split drm properties into a separate patch
- Remove dummy funcs
- Don't add offset as it's already done by a new helper
- Change the SPDX identifier format
- Minor change of a commit message
---
---
drivers/gpu/drm/xlnx/zynqmp_disp.c | 2680 ++++++++++++++++++++++++++++++++++++
drivers/gpu/drm/xlnx/zynqmp_disp.h | 36 +
2 files changed, 2716 insertions(+)
create mode 100644 drivers/gpu/drm/xlnx/zynqmp_disp.c
create mode 100644 drivers/gpu/drm/xlnx/zynqmp_disp.h
diff --git a/drivers/gpu/drm/xlnx/zynqmp_disp.c b/drivers/gpu/drm/xlnx/zynqmp_disp.c
new file mode 100644
index 0000000..65519ca
--- /dev/null
+++ b/drivers/gpu/drm/xlnx/zynqmp_disp.c
@@ -0,0 +1,2680 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ZynqMP Display Controller Driver
+ *
+ * Copyright (C) 2017 - 2018 Xilinx, Inc.
+ *
+ * Author: Hyun Woo Kwon <hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <drm/drmP.h>
+#include <drm/drm_atomic.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_fb_cma_helper.h>
+#include <drm/drm_fourcc.h>
+#include <drm/drm_plane_helper.h>
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/dmaengine.h>
+#include <linux/interrupt.h>
+#include <linux/irqreturn.h>
+#include <linux/list.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_dma.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/spinlock.h>
+#include <linux/uaccess.h>
+
+#include "xlnx_crtc.h"
+#include "xlnx_fb.h"
+#include "zynqmp_disp.h"
+#include "zynqmp_dp.h"
+#include "zynqmp_dpsub.h"
+
+/*
+ * Overview
+ * --------
+ *
+ * The display part of ZynqMP DP subsystem. Internally, the device
+ * is partitioned into 3 blocks: AV buffer manager, Blender, Audio.
+ * The driver creates the DRM crtc and plane objectes and maps the DRM
+ * interface into those 3 blocks. In high level, the driver is layered
+ * in the following way:
+ *
+ * zynqmp_disp_crtc & zynqmp_disp_plane
+ * |->zynqmp_disp
+ * |->zynqmp_disp_aud
+ * |->zynqmp_disp_blend
+ * |->zynqmp_disp_av_buf
+ *
+ * The driver APIs are used externally by
+ * - zynqmp_dpsub: Top level ZynqMP DP subsystem driver
+ * - zynqmp_dp: ZynqMP DP driver
+ * - xlnx_crtc: Xilinx DRM specific crtc functions
+ */
+
+/* Blender registers */
+#define ZYNQMP_DISP_V_BLEND_BG_CLR_0 0x0
+#define ZYNQMP_DISP_V_BLEND_BG_CLR_1 0x4
+#define ZYNQMP_DISP_V_BLEND_BG_CLR_2 0x8
+#define ZYNQMP_DISP_V_BLEND_BG_MAX 0xfff
+#define ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA 0xc
+#define ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA_MASK 0x1fe
+#define ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA_MAX 0xff
+#define ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT 0x14
+#define ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_RGB 0x0
+#define ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_YCBCR444 0x1
+#define ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_YCBCR422 0x2
+#define ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_YONLY 0x3
+#define ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_XVYCC 0x4
+#define ZYNQMP_DISP_V_BLEND_OUTPUT_EN_DOWNSAMPLE BIT(4)
+#define ZYNQMP_DISP_V_BLEND_LAYER_CONTROL 0x18
+#define ZYNQMP_DISP_V_BLEND_LAYER_CONTROL_EN_US BIT(0)
+#define ZYNQMP_DISP_V_BLEND_LAYER_CONTROL_RGB BIT(1)
+#define ZYNQMP_DISP_V_BLEND_LAYER_CONTROL_BYPASS BIT(8)
+#define ZYNQMP_DISP_V_BLEND_NUM_COEFF 9
+#define ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF0 0x20
+#define ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF1 0x24
+#define ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF2 0x28
+#define ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF3 0x2c
+#define ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF4 0x30
+#define ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF5 0x34
+#define ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF6 0x38
+#define ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF7 0x3c
+#define ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF8 0x40
+#define ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF0 0x44
+#define ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF1 0x48
+#define ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF2 0x4c
+#define ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF3 0x50
+#define ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF4 0x54
+#define ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF5 0x58
+#define ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF6 0x5c
+#define ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF7 0x60
+#define ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF8 0x64
+#define ZYNQMP_DISP_V_BLEND_NUM_OFFSET 3
+#define ZYNQMP_DISP_V_BLEND_LUMA_IN1CSC_OFFSET 0x68
+#define ZYNQMP_DISP_V_BLEND_CR_IN1CSC_OFFSET 0x6c
+#define ZYNQMP_DISP_V_BLEND_CB_IN1CSC_OFFSET 0x70
+#define ZYNQMP_DISP_V_BLEND_LUMA_OUTCSC_OFFSET 0x74
+#define ZYNQMP_DISP_V_BLEND_CR_OUTCSC_OFFSET 0x78
+#define ZYNQMP_DISP_V_BLEND_CB_OUTCSC_OFFSET 0x7c
+#define ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF0 0x80
+#define ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF1 0x84
+#define ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF2 0x88
+#define ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF3 0x8c
+#define ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF4 0x90
+#define ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF5 0x94
+#define ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF6 0x98
+#define ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF7 0x9c
+#define ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF8 0xa0
+#define ZYNQMP_DISP_V_BLEND_LUMA_IN2CSC_OFFSET 0xa4
+#define ZYNQMP_DISP_V_BLEND_CR_IN2CSC_OFFSET 0xa8
+#define ZYNQMP_DISP_V_BLEND_CB_IN2CSC_OFFSET 0xac
+#define ZYNQMP_DISP_V_BLEND_CHROMA_KEY_ENABLE 0x1d0
+#define ZYNQMP_DISP_V_BLEND_CHROMA_KEY_COMP1 0x1d4
+#define ZYNQMP_DISP_V_BLEND_CHROMA_KEY_COMP2 0x1d8
+#define ZYNQMP_DISP_V_BLEND_CHROMA_KEY_COMP3 0x1dc
+
+/* AV buffer manager registers */
+#define ZYNQMP_DISP_AV_BUF_FMT 0x0
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_SHIFT 0
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_MASK (0x1f << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_UYVY (0 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_VYUY (1 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YVYU (2 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YUYV (3 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16 (4 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV24 (5 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI (6 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_MONO (7 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI2 (8 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YUV444 (9 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_RGB888 (10 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_RGBA8880 (11 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_RGB888_10 (12 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YUV444_10 (13 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI2_10 (14 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI_10 (15 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16_10 (16 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV24_10 (17 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YONLY_10 (18 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16_420 (19 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI_420 (20 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI2_420 (21 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16_420_10 (22 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI_420_10 (23 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI2_420_10 (24 << 0)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_SHIFT 8
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_MASK (0xf << 8)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGBA8888 (0 << 8)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_ABGR8888 (1 << 8)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGB888 (2 << 8)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_BGR888 (3 << 8)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGBA5551 (4 << 8)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGBA4444 (5 << 8)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGB565 (6 << 8)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_8BPP (7 << 8)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_4BPP (8 << 8)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_2BPP (9 << 8)
+#define ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_1BPP (10 << 8)
+#define ZYNQMP_DISP_AV_BUF_NON_LIVE_LATENCY 0x8
+#define ZYNQMP_DISP_AV_BUF_CHBUF 0x10
+#define ZYNQMP_DISP_AV_BUF_CHBUF_EN BIT(0)
+#define ZYNQMP_DISP_AV_BUF_CHBUF_FLUSH BIT(1)
+#define ZYNQMP_DISP_AV_BUF_CHBUF_BURST_LEN_SHIFT 2
+#define ZYNQMP_DISP_AV_BUF_CHBUF_BURST_LEN_MASK (0xf << 2)
+#define ZYNQMP_DISP_AV_BUF_CHBUF_BURST_LEN_MAX 0xf
+#define ZYNQMP_DISP_AV_BUF_CHBUF_BURST_LEN_AUD_MAX 0x3
+#define ZYNQMP_DISP_AV_BUF_STATUS 0x28
+#define ZYNQMP_DISP_AV_BUF_STC_CTRL 0x2c
+#define ZYNQMP_DISP_AV_BUF_STC_CTRL_EN BIT(0)
+#define ZYNQMP_DISP_AV_BUF_STC_CTRL_EVENT_SHIFT 1
+#define ZYNQMP_DISP_AV_BUF_STC_CTRL_EVENT_EX_VSYNC 0
+#define ZYNQMP_DISP_AV_BUF_STC_CTRL_EVENT_EX_VID 1
+#define ZYNQMP_DISP_AV_BUF_STC_CTRL_EVENT_EX_AUD 2
+#define ZYNQMP_DISP_AV_BUF_STC_CTRL_EVENT_INT_VSYNC 3
+#define ZYNQMP_DISP_AV_BUF_STC_INIT_VALUE0 0x30
+#define ZYNQMP_DISP_AV_BUF_STC_INIT_VALUE1 0x34
+#define ZYNQMP_DISP_AV_BUF_STC_ADJ 0x38
+#define ZYNQMP_DISP_AV_BUF_STC_VID_VSYNC_TS0 0x3c
+#define ZYNQMP_DISP_AV_BUF_STC_VID_VSYNC_TS1 0x40
+#define ZYNQMP_DISP_AV_BUF_STC_EXT_VSYNC_TS0 0x44
+#define ZYNQMP_DISP_AV_BUF_STC_EXT_VSYNC_TS1 0x48
+#define ZYNQMP_DISP_AV_BUF_STC_CUSTOM_EVENT_TS0 0x4c
+#define ZYNQMP_DISP_AV_BUF_STC_CUSTOM_EVENT_TS1 0x50
+#define ZYNQMP_DISP_AV_BUF_STC_CUSTOM_EVENT2_TS0 0x54
+#define ZYNQMP_DISP_AV_BUF_STC_CUSTOM_EVENT2_TS1 0x58
+#define ZYNQMP_DISP_AV_BUF_STC_SNAPSHOT0 0x60
+#define ZYNQMP_DISP_AV_BUF_STC_SNAPSHOT1 0x64
+#define ZYNQMP_DISP_AV_BUF_OUTPUT 0x70
+#define ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_SHIFT 0
+#define ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_MASK (0x3 << 0)
+#define ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_LIVE (0 << 0)
+#define ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_MEM (1 << 0)
+#define ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_PATTERN (2 << 0)
+#define ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_NONE (3 << 0)
+#define ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_SHIFT 2
+#define ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_MASK (0x3 << 2)
+#define ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_DISABLE (0 << 2)
+#define ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_MEM (1 << 2)
+#define ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_LIVE (2 << 2)
+#define ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_NONE (3 << 2)
+#define ZYNQMP_DISP_AV_BUF_OUTPUT_AUD1_SHIFT 4
+#define ZYNQMP_DISP_AV_BUF_OUTPUT_AUD1_MASK (0x3 << 4)
+#define ZYNQMP_DISP_AV_BUF_OUTPUT_AUD1_PL (0 << 4)
+#define ZYNQMP_DISP_AV_BUF_OUTPUT_AUD1_MEM (1 << 4)
+#define ZYNQMP_DISP_AV_BUF_OUTPUT_AUD1_PATTERN (2 << 4)
+#define ZYNQMP_DISP_AV_BUF_OUTPUT_AUD1_DISABLE (3 << 4)
+#define ZYNQMP_DISP_AV_BUF_OUTPUT_AUD2_EN BIT(6)
+#define ZYNQMP_DISP_AV_BUF_HCOUNT_VCOUNT_INT0 0x74
+#define ZYNQMP_DISP_AV_BUF_HCOUNT_VCOUNT_INT1 0x78
+#define ZYNQMP_DISP_AV_BUF_PATTERN_GEN_SELECT 0x100
+#define ZYNQMP_DISP_AV_BUF_CLK_SRC 0x120
+#define ZYNQMP_DISP_AV_BUF_CLK_SRC_VID_FROM_PS BIT(0)
+#define ZYNQMP_DISP_AV_BUF_CLK_SRC_AUD_FROM_PS BIT(1)
+#define ZYNQMP_DISP_AV_BUF_CLK_SRC_VID_INTERNAL_TIMING BIT(2)
+#define ZYNQMP_DISP_AV_BUF_SRST_REG 0x124
+#define ZYNQMP_DISP_AV_BUF_SRST_REG_VID_RST BIT(1)
+#define ZYNQMP_DISP_AV_BUF_AUDIO_CH_CONFIG 0x12c
+#define ZYNQMP_DISP_AV_BUF_GFX_COMP0_SF 0x200
+#define ZYNQMP_DISP_AV_BUF_GFX_COMP1_SF 0x204
+#define ZYNQMP_DISP_AV_BUF_GFX_COMP2_SF 0x208
+#define ZYNQMP_DISP_AV_BUF_VID_COMP0_SF 0x20c
+#define ZYNQMP_DISP_AV_BUF_VID_COMP1_SF 0x210
+#define ZYNQMP_DISP_AV_BUF_VID_COMP2_SF 0x214
+#define ZYNQMP_DISP_AV_BUF_LIVE_VID_COMP0_SF 0x218
+#define ZYNQMP_DISP_AV_BUF_LIVE_VID_COMP1_SF 0x21c
+#define ZYNQMP_DISP_AV_BUF_LIVE_VID_COMP2_SF 0x220
+#define ZYNQMP_DISP_AV_BUF_LIVE_VID_CONFIG 0x224
+#define ZYNQMP_DISP_AV_BUF_LIVE_GFX_COMP0_SF 0x228
+#define ZYNQMP_DISP_AV_BUF_LIVE_GFX_COMP1_SF 0x22c
+#define ZYNQMP_DISP_AV_BUF_LIVE_GFX_COMP2_SF 0x230
+#define ZYNQMP_DISP_AV_BUF_LIVE_GFX_CONFIG 0x234
+#define ZYNQMP_DISP_AV_BUF_4BIT_SF 0x11111
+#define ZYNQMP_DISP_AV_BUF_5BIT_SF 0x10842
+#define ZYNQMP_DISP_AV_BUF_6BIT_SF 0x10410
+#define ZYNQMP_DISP_AV_BUF_8BIT_SF 0x10101
+#define ZYNQMP_DISP_AV_BUF_10BIT_SF 0x10040
+#define ZYNQMP_DISP_AV_BUF_NULL_SF 0
+#define ZYNQMP_DISP_AV_BUF_NUM_SF 3
+#define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_BPC_6 0x0
+#define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_BPC_8 0x1
+#define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_BPC_10 0x2
+#define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_BPC_12 0x3
+#define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_BPC_MASK GENMASK(2, 0)
+#define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_RGB 0x0
+#define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_YUV444 0x1
+#define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_YUV422 0x2
+#define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_YONLY 0x3
+#define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_MASK GENMASK(5, 4)
+#define ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_CB_FIRST BIT(8)
+#define ZYNQMP_DISP_AV_BUF_PALETTE_MEMORY 0x400
+
+/* Audio registers */
+#define ZYNQMP_DISP_AUD_MIXER_VOLUME 0x0
+#define ZYNQMP_DISP_AUD_MIXER_VOLUME_NO_SCALE 0x20002000
+#define ZYNQMP_DISP_AUD_MIXER_META_DATA 0x4
+#define ZYNQMP_DISP_AUD_CH_STATUS0 0x8
+#define ZYNQMP_DISP_AUD_CH_STATUS1 0xc
+#define ZYNQMP_DISP_AUD_CH_STATUS2 0x10
+#define ZYNQMP_DISP_AUD_CH_STATUS3 0x14
+#define ZYNQMP_DISP_AUD_CH_STATUS4 0x18
+#define ZYNQMP_DISP_AUD_CH_STATUS5 0x1c
+#define ZYNQMP_DISP_AUD_CH_A_DATA0 0x20
+#define ZYNQMP_DISP_AUD_CH_A_DATA1 0x24
+#define ZYNQMP_DISP_AUD_CH_A_DATA2 0x28
+#define ZYNQMP_DISP_AUD_CH_A_DATA3 0x2c
+#define ZYNQMP_DISP_AUD_CH_A_DATA4 0x30
+#define ZYNQMP_DISP_AUD_CH_A_DATA5 0x34
+#define ZYNQMP_DISP_AUD_CH_B_DATA0 0x38
+#define ZYNQMP_DISP_AUD_CH_B_DATA1 0x3c
+#define ZYNQMP_DISP_AUD_CH_B_DATA2 0x40
+#define ZYNQMP_DISP_AUD_CH_B_DATA3 0x44
+#define ZYNQMP_DISP_AUD_CH_B_DATA4 0x48
+#define ZYNQMP_DISP_AUD_CH_B_DATA5 0x4c
+#define ZYNQMP_DISP_AUD_SOFT_RESET 0xc00
+#define ZYNQMP_DISP_AUD_SOFT_RESET_AUD_SRST BIT(0)
+
+#define ZYNQMP_DISP_AV_BUF_NUM_VID_GFX_BUFFERS 4
+#define ZYNQMP_DISP_AV_BUF_NUM_BUFFERS 6
+
+#define ZYNQMP_DISP_NUM_LAYERS 2
+#define ZYNQMP_DISP_MAX_NUM_SUB_PLANES 3
+/*
+ * 3840x2160 is advertised max resolution, but almost any resolutions under
+ * 300Mhz pixel rate would work. Thus put 4096 as maximum width and height.
+ */
+#define ZYNQMP_DISP_MAX_WIDTH 4096
+#define ZYNQMP_DISP_MAX_HEIGHT 4096
+/* 44 bit addressing. This is acutally DPDMA limitation */
+#define ZYNQMP_DISP_MAX_DMA_BIT 44
+
+/**
+ * enum zynqmp_disp_layer_type - Layer type (can be used for hw ID)
+ * @ZYNQMP_DISP_LAYER_VID: Video layer
+ * @ZYNQMP_DISP_LAYER_GFX: Graphics layer
+ */
+enum zynqmp_disp_layer_type {
+ ZYNQMP_DISP_LAYER_VID,
+ ZYNQMP_DISP_LAYER_GFX
+};
+
+/**
+ * enum zynqmp_disp_layer_mode - Layer mode
+ * @ZYNQMP_DISP_LAYER_NONLIVE: non-live (memory) mode
+ * @ZYNQMP_DISP_LAYER_LIVE: live (stream) mode
+ */
+enum zynqmp_disp_layer_mode {
+ ZYNQMP_DISP_LAYER_NONLIVE,
+ ZYNQMP_DISP_LAYER_LIVE
+};
+
+/**
+ * struct zynqmp_disp_layer_dma - struct for DMA engine
+ * @chan: DMA channel
+ * @is_active: flag if the DMA is active
+ * @xt: Interleaved desc config container
+ * @sgl: Data chunk for dma_interleaved_template
+ */
+struct zynqmp_disp_layer_dma {
+ struct dma_chan *chan;
+ bool is_active;
+ struct dma_interleaved_template xt;
+ struct data_chunk sgl[1];
+};
+
+/**
+ * struct zynqmp_disp_layer - Display subsystem layer
+ * @plane: DRM plane
+ * @of_node: device node
+ * @dma: struct for DMA engine
+ * @num_chan: Number of DMA channel
+ * @id: Layer ID
+ * @offset: Layer offset in the register space
+ * @enabled: flag if enabled
+ * @fmt: Current format descriptor
+ * @drm_fmts: Array of supported DRM formats
+ * @num_fmts: Number of supported DRM formats
+ * @bus_fmts: Array of supported bus formats
+ * @num_bus_fmts: Number of supported bus formats
+ * @w: Width
+ * @h: Height
+ * @mode: the operation mode
+ * @other: other layer
+ * @disp: back pointer to struct zynqmp_disp
+ */
+struct zynqmp_disp_layer {
+ struct drm_plane plane;
+ struct device_node *of_node;
+ struct zynqmp_disp_layer_dma dma[ZYNQMP_DISP_MAX_NUM_SUB_PLANES];
+ unsigned int num_chan;
+ enum zynqmp_disp_layer_type id;
+ u32 offset;
+ u8 enabled;
+ const struct zynqmp_disp_fmt *fmt;
+ u32 *drm_fmts;
+ unsigned int num_fmts;
+ u32 *bus_fmts;
+ unsigned int num_bus_fmts;
+ u32 w;
+ u32 h;
+ enum zynqmp_disp_layer_mode mode;
+ struct zynqmp_disp_layer *other;
+ struct zynqmp_disp *disp;
+};
+
+/**
+ * struct zynqmp_disp_blend - Blender
+ * @base: Base address offset
+ */
+struct zynqmp_disp_blend {
+ void __iomem *base;
+};
+
+/**
+ * struct zynqmp_disp_av_buf - AV buffer manager
+ * @base: Base address offset
+ */
+struct zynqmp_disp_av_buf {
+ void __iomem *base;
+};
+
+/**
+ * struct zynqmp_disp_aud - Audio
+ * @base: Base address offset
+ */
+struct zynqmp_disp_aud {
+ void __iomem *base;
+};
+
+/**
+ * struct zynqmp_disp - Display subsystem
+ * @xlnx_crtc: Xilinx DRM crtc
+ * @dev: device structure
+ * @dpsub: Display subsystem
+ * @drm: DRM core
+ * @enabled: flag if enabled
+ * @blend: Blender block
+ * @av_buf: AV buffer manager block
+ * @aud:Audio block
+ * @layers: layers
+ * @alpha: current global alpha value
+ * @alpha_en: flag if the global alpha is enabled
+ * @color: current output color value
+ * @bg_c0: current value of 1st background color component
+ * @bg_c1: current value of 2nd background color component
+ * @bg_c2: current value of 3rd background color component
+ * @tpg_on: current TPG mode state
+ * @event: pending vblank event request
+ * @_ps_pclk: Pixel clock from PS
+ * @_pl_pclk: Pixel clock from PL
+ * @pclk: Pixel clock
+ * @pclk_en: Flag if the pixel clock is enabled
+ * @_ps_audclk: Audio clock from PS
+ * @_pl_audclk: Audio clock from PL
+ * @audclk: Audio clock
+ * @audclk_en: Flag if the audio clock is enabled
+ * @aclk: APB clock
+ * @aclk_en: Flag if the APB clock is enabled
+ */
+struct zynqmp_disp {
+ struct xlnx_crtc xlnx_crtc;
+ struct device *dev;
+ struct zynqmp_dpsub *dpsub;
+ struct drm_device *drm;
+ bool enabled;
+ struct zynqmp_disp_blend blend;
+ struct zynqmp_disp_av_buf av_buf;
+ struct zynqmp_disp_aud aud;
+ struct zynqmp_disp_layer layers[ZYNQMP_DISP_NUM_LAYERS];
+ u32 alpha;
+ bool alpha_en;
+ unsigned int color;
+ u32 bg_c0;
+ u32 bg_c1;
+ u32 bg_c2;
+ bool tpg_on;
+ struct drm_pending_vblank_event *event;
+ /* Don't operate directly on _ps_ */
+ struct clk *_ps_pclk;
+ struct clk *_pl_pclk;
+ struct clk *pclk;
+ bool pclk_en;
+ struct clk *_ps_audclk;
+ struct clk *_pl_audclk;
+ struct clk *audclk;
+ bool audclk_en;
+ struct clk *aclk;
+ bool aclk_en;
+};
+
+/**
+ * struct zynqmp_disp_fmt - Display subsystem format mapping
+ * @drm_fmt: drm format
+ * @disp_fmt: Display subsystem format
+ * @bus_fmt: Bus formats (live formats)
+ * @rgb: flag for RGB formats
+ * @swap: flag to swap r & b for rgb formats, and u & v for yuv formats
+ * @chroma_sub: flag for chroma subsampled formats
+ * @sf: scaling factors for upto 3 color components
+ */
+struct zynqmp_disp_fmt {
+ u32 drm_fmt;
+ u32 disp_fmt;
+ u32 bus_fmt;
+ bool rgb;
+ bool swap;
+ bool chroma_sub;
+ u32 sf[3];
+};
+
+static void zynqmp_disp_write(void __iomem *base, int offset, u32 val)
+{
+ writel(val, base + offset);
+}
+
+static u32 zynqmp_disp_read(void __iomem *base, int offset)
+{
+ return readl(base + offset);
+}
+
+static void zynqmp_disp_clr(void __iomem *base, int offset, u32 clr)
+{
+ zynqmp_disp_write(base, offset, zynqmp_disp_read(base, offset) & ~clr);
+}
+
+static void zynqmp_disp_set(void __iomem *base, int offset, u32 set)
+{
+ zynqmp_disp_write(base, offset, zynqmp_disp_read(base, offset) | set);
+}
+
+/*
+ * Clock functions
+ */
+
+/**
+ * zynqmp_disp_clk_enable - Enable the clock if needed
+ * @clk: clk device
+ * @flag: flag if the clock is enabled
+ *
+ * Enable the clock only if it's not enabled @flag.
+ *
+ * Return: value from clk_prepare_enable().
+ */
+static int zynqmp_disp_clk_enable(struct clk *clk, bool *flag)
+{
+ int ret = 0;
+
+ if (!*flag) {
+ ret = clk_prepare_enable(clk);
+ if (!ret)
+ *flag = true;
+ }
+
+ return ret;
+}
+
+/**
+ * zynqmp_disp_clk_enable - Enable the clock if needed
+ * @clk: clk device
+ * @flag: flag if the clock is enabled
+ *
+ * Disable the clock only if it's enabled @flag.
+ */
+static void zynqmp_disp_clk_disable(struct clk *clk, bool *flag)
+{
+ if (*flag) {
+ clk_disable_unprepare(clk);
+ *flag = false;
+ }
+}
+
+/**
+ * zynqmp_disp_clk_enable - Enable and disable the clock
+ * @clk: clk device
+ * @flag: flag if the clock is enabled
+ *
+ * This is to ensure the clock is disabled. The initial hardware state is
+ * unknown, and this makes sure that the clock is disabled.
+ *
+ * Return: value from clk_prepare_enable().
+ */
+static int zynqmp_disp_clk_enable_disable(struct clk *clk, bool *flag)
+{
+ int ret = 0;
+
+ if (!*flag) {
+ ret = clk_prepare_enable(clk);
+ clk_disable_unprepare(clk);
+ }
+
+ return ret;
+}
+
+/*
+ * Blender functions
+ */
+
+/**
+ * zynqmp_disp_blend_set_output_fmt - Set the output format of the blend
+ * @blend: blend object
+ * @fmt: output format
+ *
+ * Set the output format to @fmt.
+ */
+static void
+zynqmp_disp_blend_set_output_fmt(struct zynqmp_disp_blend *blend, u32 fmt)
+{
+ u16 reset_coeffs[] = { 0x1000, 0x0, 0x0,
+ 0x0, 0x1000, 0x0,
+ 0x0, 0x0, 0x1000 };
+ u32 reset_offsets[] = { 0x0, 0x0, 0x0 };
+ u16 sdtv_coeffs[] = { 0x4c9, 0x864, 0x1d3,
+ 0x7d4d, 0x7ab3, 0x800,
+ 0x800, 0x794d, 0x7eb3 };
+ u32 full_range_offsets[] = { 0x0, 0x8000000, 0x8000000 };
+ u16 *coeffs;
+ u32 *offsets;
+ u32 offset, i;
+
+ zynqmp_disp_write(blend->base, ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT, fmt);
+ if (fmt == ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_RGB) {
+ coeffs = reset_coeffs;
+ offsets = reset_offsets;
+ } else {
+ /* Hardcode Full-range SDTV values. Can be runtime config */
+ coeffs = sdtv_coeffs;
+ offsets = full_range_offsets;
+ }
+
+ offset = ZYNQMP_DISP_V_BLEND_RGB2YCBCR_COEFF0;
+ for (i = 0; i < ZYNQMP_DISP_V_BLEND_NUM_COEFF; i++)
+ zynqmp_disp_write(blend->base, offset + i * 4, coeffs[i]);
+
+ offset = ZYNQMP_DISP_V_BLEND_LUMA_OUTCSC_OFFSET;
+ for (i = 0; i < ZYNQMP_DISP_V_BLEND_NUM_OFFSET; i++)
+ zynqmp_disp_write(blend->base, offset + i * 4, offsets[i]);
+}
+
+/**
+ * zynqmp_disp_blend_layer_enable - Enable a layer
+ * @blend: blend object
+ * @layer: layer to enable
+ *
+ * Enable a layer @layer.
+ */
+static void zynqmp_disp_blend_layer_enable(struct zynqmp_disp_blend *blend,
+ struct zynqmp_disp_layer *layer)
+{
+ u32 reg, offset, i, s0, s1;
+ u16 sdtv_coeffs[] = { 0x1000, 0x166f, 0x0,
+ 0x1000, 0x7483, 0x7a7f,
+ 0x1000, 0x0, 0x1c5a };
+ u16 swap_coeffs[] = { 0x1000, 0x0, 0x0,
+ 0x0, 0x1000, 0x0,
+ 0x0, 0x0, 0x1000 };
+ u16 *coeffs;
+ u32 offsets[] = { 0x0, 0x1800, 0x1800 };
+
+ reg = layer->fmt->rgb ? ZYNQMP_DISP_V_BLEND_LAYER_CONTROL_RGB : 0;
+ reg |= layer->fmt->chroma_sub ?
+ ZYNQMP_DISP_V_BLEND_LAYER_CONTROL_EN_US : 0;
+
+ zynqmp_disp_write(blend->base,
+ ZYNQMP_DISP_V_BLEND_LAYER_CONTROL + layer->offset,
+ reg);
+
+ if (layer->id == ZYNQMP_DISP_LAYER_VID)
+ offset = ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF0;
+ else
+ offset = ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF0;
+
+ if (!layer->fmt->rgb) {
+ coeffs = sdtv_coeffs;
+ s0 = 1;
+ s1 = 2;
+ } else {
+ coeffs = swap_coeffs;
+ s0 = 0;
+ s1 = 2;
+
+ /* No offset for RGB formats */
+ for (i = 0; i < ZYNQMP_DISP_V_BLEND_NUM_OFFSET; i++)
+ offsets[i] = 0;
+ }
+
+ if (layer->fmt->swap) {
+ for (i = 0; i < 3; i++) {
+ coeffs[i * 3 + s0] ^= coeffs[i * 3 + s1];
+ coeffs[i * 3 + s1] ^= coeffs[i * 3 + s0];
+ coeffs[i * 3 + s0] ^= coeffs[i * 3 + s1];
+ }
+ }
+
+ /* Program coefficients. Can be runtime configurable */
+ for (i = 0; i < ZYNQMP_DISP_V_BLEND_NUM_COEFF; i++)
+ zynqmp_disp_write(blend->base, offset + i * 4, coeffs[i]);
+
+ if (layer->id == ZYNQMP_DISP_LAYER_VID)
+ offset = ZYNQMP_DISP_V_BLEND_LUMA_IN1CSC_OFFSET;
+ else
+ offset = ZYNQMP_DISP_V_BLEND_LUMA_IN2CSC_OFFSET;
+
+ /* Program offsets. Can be runtime configurable */
+ for (i = 0; i < ZYNQMP_DISP_V_BLEND_NUM_OFFSET; i++)
+ zynqmp_disp_write(blend->base, offset + i * 4, offsets[i]);
+}
+
+/**
+ * zynqmp_disp_blend_layer_disable - Disable a layer
+ * @blend: blend object
+ * @layer: layer to disable
+ *
+ * Disable a layer @layer.
+ */
+static void zynqmp_disp_blend_layer_disable(struct zynqmp_disp_blend *blend,
+ struct zynqmp_disp_layer *layer)
+{
+ u32 offset;
+ unsigned int i;
+
+ zynqmp_disp_write(blend->base,
+ ZYNQMP_DISP_V_BLEND_LAYER_CONTROL + layer->offset, 0);
+
+ if (layer->id == ZYNQMP_DISP_LAYER_VID)
+ offset = ZYNQMP_DISP_V_BLEND_IN1CSC_COEFF0;
+ else
+ offset = ZYNQMP_DISP_V_BLEND_IN2CSC_COEFF0;
+ for (i = 0; i < ZYNQMP_DISP_V_BLEND_NUM_COEFF; i++)
+ zynqmp_disp_write(blend->base, offset + i * 4, 0);
+
+ if (layer->id == ZYNQMP_DISP_LAYER_VID)
+ offset = ZYNQMP_DISP_V_BLEND_LUMA_IN1CSC_OFFSET;
+ else
+ offset = ZYNQMP_DISP_V_BLEND_LUMA_IN2CSC_OFFSET;
+
+ for (i = 0; i < ZYNQMP_DISP_V_BLEND_NUM_OFFSET; i++)
+ zynqmp_disp_write(blend->base, offset + i * 4, 0);
+}
+
+/**
+ * zynqmp_disp_blend_set_bg_color - Set the background color
+ * @blend: blend object
+ * @c0: color component 0
+ * @c1: color component 1
+ * @c2: color component 2
+ *
+ * Set the background color.
+ */
+static void zynqmp_disp_blend_set_bg_color(struct zynqmp_disp_blend *blend,
+ u32 c0, u32 c1, u32 c2)
+{
+ zynqmp_disp_write(blend->base, ZYNQMP_DISP_V_BLEND_BG_CLR_0, c0);
+ zynqmp_disp_write(blend->base, ZYNQMP_DISP_V_BLEND_BG_CLR_1, c1);
+ zynqmp_disp_write(blend->base, ZYNQMP_DISP_V_BLEND_BG_CLR_2, c2);
+}
+
+/**
+ * zynqmp_disp_blend_set_alpha - Set the alpha for blending
+ * @blend: blend object
+ * @alpha: alpha value to be used
+ *
+ * Set the alpha for blending.
+ */
+static void
+zynqmp_disp_blend_set_alpha(struct zynqmp_disp_blend *blend, u32 alpha)
+{
+ u32 reg;
+
+ reg = zynqmp_disp_read(blend->base,
+ ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA);
+ reg &= ~ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA_MASK;
+ reg |= alpha << 1;
+ zynqmp_disp_write(blend->base, ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA,
+ reg);
+}
+
+/**
+ * zynqmp_disp_blend_enable_alpha - Enable/disable the global alpha
+ * @blend: blend object
+ * @enable: flag to enable or disable alpha blending
+ *
+ * Enable/disable the global alpha blending based on @enable.
+ */
+static void
+zynqmp_disp_blend_enable_alpha(struct zynqmp_disp_blend *blend, bool enable)
+{
+ if (enable)
+ zynqmp_disp_set(blend->base,
+ ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA, BIT(0));
+ else
+ zynqmp_disp_clr(blend->base,
+ ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA, BIT(0));
+}
+
+/* List of blend output formats */
+/* The id / order should be aligned with zynqmp_disp_color_enum */
+static const struct zynqmp_disp_fmt blend_output_fmts[] = {
+ {
+ .disp_fmt = ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_RGB,
+ }, {
+ .disp_fmt = ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_YCBCR444,
+ }, {
+ .disp_fmt = ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_YCBCR422,
+ }, {
+ .disp_fmt = ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_YONLY,
+ }
+};
+
+/*
+ * AV buffer manager functions
+ */
+
+/* List of video layer formats */
+#define ZYNQMP_DISP_AV_BUF_VID_FMT_YUYV 2
+static const struct zynqmp_disp_fmt av_buf_vid_fmts[] = {
+ {
+ .drm_fmt = DRM_FORMAT_VYUY,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_VID_VYUY,
+ .rgb = false,
+ .swap = true,
+ .chroma_sub = true,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_UYVY,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_VID_VYUY,
+ .rgb = false,
+ .swap = false,
+ .chroma_sub = true,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_YUYV,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YUYV,
+ .rgb = false,
+ .swap = false,
+ .chroma_sub = true,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_YVYU,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YUYV,
+ .rgb = false,
+ .swap = true,
+ .chroma_sub = true,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_YUV422,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16,
+ .rgb = false,
+ .swap = false,
+ .chroma_sub = true,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_YVU422,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16,
+ .rgb = false,
+ .swap = true,
+ .chroma_sub = true,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_YUV444,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV24,
+ .rgb = false,
+ .swap = false,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_YVU444,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV24,
+ .rgb = false,
+ .swap = true,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_NV16,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI,
+ .rgb = false,
+ .swap = false,
+ .chroma_sub = true,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_NV61,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI,
+ .rgb = false,
+ .swap = true,
+ .chroma_sub = true,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_BGR888,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_VID_RGB888,
+ .rgb = true,
+ .swap = false,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_RGB888,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_VID_RGB888,
+ .rgb = true,
+ .swap = true,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_XBGR8888,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_VID_RGBA8880,
+ .rgb = true,
+ .swap = false,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_XRGB8888,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_VID_RGBA8880,
+ .rgb = true,
+ .swap = true,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_XBGR2101010,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_VID_RGB888_10,
+ .rgb = true,
+ .swap = false,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_10BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_10BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_10BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_XRGB2101010,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_VID_RGB888_10,
+ .rgb = true,
+ .swap = true,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_10BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_10BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_10BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_YUV420,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16_420,
+ .rgb = false,
+ .swap = false,
+ .chroma_sub = true,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_YVU420,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16_420,
+ .rgb = false,
+ .swap = true,
+ .chroma_sub = true,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_NV12,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI_420,
+ .rgb = false,
+ .swap = false,
+ .chroma_sub = true,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_NV21,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_VID_YV16CI_420,
+ .rgb = false,
+ .swap = true,
+ .chroma_sub = true,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }
+};
+
+/* List of graphics layer formats */
+#define ZYNQMP_DISP_AV_BUF_GFX_FMT_RGB565 10
+static const struct zynqmp_disp_fmt av_buf_gfx_fmts[] = {
+ {
+ .drm_fmt = DRM_FORMAT_ABGR8888,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGBA8888,
+ .rgb = true,
+ .swap = false,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_ARGB8888,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGBA8888,
+ .rgb = true,
+ .swap = true,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_RGBA8888,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_ABGR8888,
+ .rgb = true,
+ .swap = false,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_BGRA8888,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_ABGR8888,
+ .rgb = true,
+ .swap = true,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_BGR888,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGB888,
+ .rgb = true,
+ .swap = false,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_RGB888,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_BGR888,
+ .rgb = true,
+ .swap = false,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_RGBA5551,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGBA5551,
+ .rgb = true,
+ .swap = false,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_5BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_5BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_5BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_BGRA5551,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGBA5551,
+ .rgb = true,
+ .swap = true,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_5BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_5BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_5BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_RGBA4444,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGBA4444,
+ .rgb = true,
+ .swap = false,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_4BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_4BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_4BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_BGRA4444,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGBA4444,
+ .rgb = true,
+ .swap = true,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_4BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_4BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_4BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_RGB565,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGB565,
+ .rgb = true,
+ .swap = false,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_5BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_6BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_5BIT_SF,
+ }, {
+ .drm_fmt = DRM_FORMAT_BGR565,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_RGB565,
+ .rgb = true,
+ .swap = true,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_5BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_6BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_5BIT_SF,
+ }
+};
+
+/* List of live formats */
+/* Format can be combination of color, bpc, and cb-cr order.
+ * - Color: RGB / YUV444 / YUV422 / Y only
+ * - BPC: 6, 8, 10, 12
+ * - Swap: Cb and Cr swap
+ * which can be 32 bus formats. Only list the subset of those for now.
+ */
+static const struct zynqmp_disp_fmt av_buf_live_fmts[] = {
+ {
+ .bus_fmt = MEDIA_BUS_FMT_RGB666_1X18,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_BPC_6 ||
+ ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_RGB,
+ .rgb = true,
+ .swap = false,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_6BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_6BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_6BIT_SF,
+ }, {
+ .bus_fmt = MEDIA_BUS_FMT_RBG888_1X24,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_BPC_8 ||
+ ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_RGB,
+ .rgb = true,
+ .swap = false,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .bus_fmt = MEDIA_BUS_FMT_UYVY8_1X16,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_BPC_8 ||
+ ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_YUV422,
+ .rgb = false,
+ .swap = false,
+ .chroma_sub = true,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .bus_fmt = MEDIA_BUS_FMT_VUY8_1X24,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_BPC_8 ||
+ ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_YUV444,
+ .rgb = false,
+ .swap = false,
+ .chroma_sub = false,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_8BIT_SF,
+ }, {
+ .bus_fmt = MEDIA_BUS_FMT_UYVY10_1X20,
+ .disp_fmt = ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_BPC_10 ||
+ ZYNQMP_DISP_AV_BUF_LIVE_CONFIG_FMT_YUV422,
+ .rgb = false,
+ .swap = false,
+ .chroma_sub = true,
+ .sf[0] = ZYNQMP_DISP_AV_BUF_10BIT_SF,
+ .sf[1] = ZYNQMP_DISP_AV_BUF_10BIT_SF,
+ .sf[2] = ZYNQMP_DISP_AV_BUF_10BIT_SF,
+ }
+};
+
+/**
+ * zynqmp_disp_av_buf_set_fmt - Set the input formats
+ * @av_buf: av buffer manager
+ * @fmt: formats
+ *
+ * Set the av buffer manager format to @fmt. @fmt should have valid values
+ * for both video and graphics layer.
+ */
+static void
+zynqmp_disp_av_buf_set_fmt(struct zynqmp_disp_av_buf *av_buf, u32 fmt)
+{
+ zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_FMT, fmt);
+}
+
+/**
+ * zynqmp_disp_av_buf_get_fmt - Get the input formats
+ * @av_buf: av buffer manager
+ *
+ * Get the input formats (which include video and graphics) of
+ * av buffer manager.
+ *
+ * Return: value of ZYNQMP_DISP_AV_BUF_FMT register.
+ */
+static u32
+zynqmp_disp_av_buf_get_fmt(struct zynqmp_disp_av_buf *av_buf)
+{
+ return zynqmp_disp_read(av_buf->base, ZYNQMP_DISP_AV_BUF_FMT);
+}
+
+/**
+ * zynqmp_disp_av_buf_set_vid_clock_src - Set the video clock source
+ * @av_buf: av buffer manager
+ * @from_ps: flag if the video clock is from ps
+ *
+ * Set the video clock source based on @from_ps. It can come from either PS or
+ * PL.
+ */
+static void
+zynqmp_disp_av_buf_set_vid_clock_src(struct zynqmp_disp_av_buf *av_buf,
+ bool from_ps)
+{
+ u32 reg = zynqmp_disp_read(av_buf->base, ZYNQMP_DISP_AV_BUF_CLK_SRC);
+
+ if (from_ps)
+ reg |= ZYNQMP_DISP_AV_BUF_CLK_SRC_VID_FROM_PS;
+ else
+ reg &= ~ZYNQMP_DISP_AV_BUF_CLK_SRC_VID_FROM_PS;
+ zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_CLK_SRC, reg);
+}
+
+/**
+ * zynqmp_disp_av_buf_set_vid_timing_src - Set the video timing source
+ * @av_buf: av buffer manager
+ * @internal: flag if the video timing is generated internally
+ *
+ * Set the video timing source based on @internal. It can come externally or
+ * be generated internally.
+ */
+static void
+zynqmp_disp_av_buf_set_vid_timing_src(struct zynqmp_disp_av_buf *av_buf,
+ bool internal)
+{
+ u32 reg = zynqmp_disp_read(av_buf->base, ZYNQMP_DISP_AV_BUF_CLK_SRC);
+
+ if (internal)
+ reg |= ZYNQMP_DISP_AV_BUF_CLK_SRC_VID_INTERNAL_TIMING;
+ else
+ reg &= ~ZYNQMP_DISP_AV_BUF_CLK_SRC_VID_INTERNAL_TIMING;
+ zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_CLK_SRC, reg);
+}
+
+/**
+ * zynqmp_disp_av_buf_set_aud_clock_src - Set the audio clock source
+ * @av_buf: av buffer manager
+ * @from_ps: flag if the video clock is from ps
+ *
+ * Set the audio clock source based on @from_ps. It can come from either PS or
+ * PL.
+ */
+static void
+zynqmp_disp_av_buf_set_aud_clock_src(struct zynqmp_disp_av_buf *av_buf,
+ bool from_ps)
+{
+ u32 reg = zynqmp_disp_read(av_buf->base, ZYNQMP_DISP_AV_BUF_CLK_SRC);
+
+ if (from_ps)
+ reg |= ZYNQMP_DISP_AV_BUF_CLK_SRC_AUD_FROM_PS;
+ else
+ reg &= ~ZYNQMP_DISP_AV_BUF_CLK_SRC_AUD_FROM_PS;
+ zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_CLK_SRC, reg);
+}
+
+/**
+ * zynqmp_disp_av_buf_enable_buf - Enable buffers
+ * @av_buf: av buffer manager
+ *
+ * Enable all (video and audio) buffers.
+ */
+static void
+zynqmp_disp_av_buf_enable_buf(struct zynqmp_disp_av_buf *av_buf)
+{
+ u32 reg, i;
+
+ reg = ZYNQMP_DISP_AV_BUF_CHBUF_EN;
+ reg |= ZYNQMP_DISP_AV_BUF_CHBUF_BURST_LEN_MAX <<
+ ZYNQMP_DISP_AV_BUF_CHBUF_BURST_LEN_SHIFT;
+
+ for (i = 0; i < ZYNQMP_DISP_AV_BUF_NUM_VID_GFX_BUFFERS; i++)
+ zynqmp_disp_write(av_buf->base,
+ ZYNQMP_DISP_AV_BUF_CHBUF + i * 4, reg);
+
+ reg = ZYNQMP_DISP_AV_BUF_CHBUF_EN;
+ reg |= ZYNQMP_DISP_AV_BUF_CHBUF_BURST_LEN_AUD_MAX <<
+ ZYNQMP_DISP_AV_BUF_CHBUF_BURST_LEN_SHIFT;
+
+ for (; i < ZYNQMP_DISP_AV_BUF_NUM_BUFFERS; i++)
+ zynqmp_disp_write(av_buf->base,
+ ZYNQMP_DISP_AV_BUF_CHBUF + i * 4, reg);
+}
+
+/**
+ * zynqmp_disp_av_buf_disable_buf - Disable buffers
+ * @av_buf: av buffer manager
+ *
+ * Disable all (video and audio) buffers.
+ */
+static void
+zynqmp_disp_av_buf_disable_buf(struct zynqmp_disp_av_buf *av_buf)
+{
+ u32 reg, i;
+
+ reg = ZYNQMP_DISP_AV_BUF_CHBUF_FLUSH & ~ZYNQMP_DISP_AV_BUF_CHBUF_EN;
+ for (i = 0; i < ZYNQMP_DISP_AV_BUF_NUM_BUFFERS; i++)
+ zynqmp_disp_write(av_buf->base,
+ ZYNQMP_DISP_AV_BUF_CHBUF + i * 4, reg);
+}
+
+/**
+ * zynqmp_disp_av_buf_enable_aud - Enable audio
+ * @av_buf: av buffer manager
+ *
+ * Enable all audio buffers.
+ */
+static void
+zynqmp_disp_av_buf_enable_aud(struct zynqmp_disp_av_buf *av_buf)
+{
+ u32 reg;
+
+ reg = zynqmp_disp_read(av_buf->base, ZYNQMP_DISP_AV_BUF_OUTPUT);
+ reg &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_AUD1_MASK;
+ reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_AUD1_MEM;
+ reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_AUD2_EN;
+ zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_OUTPUT, reg);
+}
+
+/**
+ * zynqmp_disp_av_buf_enable - Enable the video pipe
+ * @av_buf: av buffer manager
+ *
+ * De-assert the video pipe reset
+ */
+static void
+zynqmp_disp_av_buf_enable(struct zynqmp_disp_av_buf *av_buf)
+{
+ zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_SRST_REG, 0);
+}
+
+/**
+ * zynqmp_disp_av_buf_disable - Disable the video pipe
+ * @av_buf: av buffer manager
+ *
+ * Assert the video pipe reset
+ */
+static void
+zynqmp_disp_av_buf_disable(struct zynqmp_disp_av_buf *av_buf)
+{
+ zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_SRST_REG,
+ ZYNQMP_DISP_AV_BUF_SRST_REG_VID_RST);
+}
+
+/**
+ * zynqmp_disp_av_buf_disable_aud - Disable audio
+ * @av_buf: av buffer manager
+ *
+ * Disable all audio buffers.
+ */
+static void
+zynqmp_disp_av_buf_disable_aud(struct zynqmp_disp_av_buf *av_buf)
+{
+ u32 reg;
+
+ reg = zynqmp_disp_read(av_buf->base, ZYNQMP_DISP_AV_BUF_OUTPUT);
+ reg &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_AUD1_MASK;
+ reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_AUD1_DISABLE;
+ reg &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_AUD2_EN;
+ zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_OUTPUT, reg);
+}
+
+/**
+ * zynqmp_disp_av_buf_set_tpg - Set TPG mode
+ * @av_buf: av buffer manager
+ * @tpg_on: if TPG should be on
+ *
+ * Set the TPG mode based on @tpg_on.
+ */
+static void zynqmp_disp_av_buf_set_tpg(struct zynqmp_disp_av_buf *av_buf,
+ bool tpg_on)
+{
+ u32 reg;
+
+ reg = zynqmp_disp_read(av_buf->base, ZYNQMP_DISP_AV_BUF_OUTPUT);
+ reg &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_MASK;
+ if (tpg_on)
+ reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_PATTERN;
+ else
+ reg &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_PATTERN;
+ zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_OUTPUT, reg);
+}
+
+/**
+ * zynqmp_disp_av_buf_enable_vid - Enable the video layer buffer
+ * @av_buf: av buffer manager
+ * @layer: layer to enable
+ * @mode: operation mode of layer
+ *
+ * Enable the video/graphics buffer for @layer.
+ */
+static void zynqmp_disp_av_buf_enable_vid(struct zynqmp_disp_av_buf *av_buf,
+ struct zynqmp_disp_layer *layer,
+ enum zynqmp_disp_layer_mode mode)
+{
+ u32 reg;
+
+ reg = zynqmp_disp_read(av_buf->base, ZYNQMP_DISP_AV_BUF_OUTPUT);
+ if (layer->id == ZYNQMP_DISP_LAYER_VID) {
+ reg &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_MASK;
+ if (mode == ZYNQMP_DISP_LAYER_NONLIVE)
+ reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_MEM;
+ else
+ reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_LIVE;
+ } else {
+ reg &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_MASK;
+ reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_MEM;
+ if (mode == ZYNQMP_DISP_LAYER_NONLIVE)
+ reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_MEM;
+ else
+ reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_LIVE;
+ }
+ zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_OUTPUT, reg);
+}
+
+/**
+ * zynqmp_disp_av_buf_disable_vid - Disable the video layer buffer
+ * @av_buf: av buffer manager
+ * @layer: layer to disable
+ *
+ * Disable the video/graphics buffer for @layer.
+ */
+static void
+zynqmp_disp_av_buf_disable_vid(struct zynqmp_disp_av_buf *av_buf,
+ struct zynqmp_disp_layer *layer)
+{
+ u32 reg;
+
+ reg = zynqmp_disp_read(av_buf->base, ZYNQMP_DISP_AV_BUF_OUTPUT);
+ if (layer->id == ZYNQMP_DISP_LAYER_VID) {
+ reg &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_MASK;
+ reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID1_NONE;
+ } else {
+ reg &= ~ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_MASK;
+ reg |= ZYNQMP_DISP_AV_BUF_OUTPUT_VID2_DISABLE;
+ }
+ zynqmp_disp_write(av_buf->base, ZYNQMP_DISP_AV_BUF_OUTPUT, reg);
+}
+
+/**
+ * zynqmp_disp_av_buf_init_sf - Initialize scaling factors
+ * @av_buf: av buffer manager
+ * @vid_fmt: video format descriptor
+ * @gfx_fmt: graphics format descriptor
+ *
+ * Initialize scaling factors for both video and graphics layers.
+ * If the format descriptor is NULL, the function skips the programming.
+ */
+static void zynqmp_disp_av_buf_init_sf(struct zynqmp_disp_av_buf *av_buf,
+ const struct zynqmp_disp_fmt *vid_fmt,
+ const struct zynqmp_disp_fmt *gfx_fmt)
+{
+ unsigned int i;
+ u32 offset;
+
+ if (gfx_fmt) {
+ offset = ZYNQMP_DISP_AV_BUF_GFX_COMP0_SF;
+ for (i = 0; i < ZYNQMP_DISP_AV_BUF_NUM_SF; i++)
+ zynqmp_disp_write(av_buf->base, offset + i * 4,
+ gfx_fmt->sf[i]);
+ }
+
+ if (vid_fmt) {
+ offset = ZYNQMP_DISP_AV_BUF_VID_COMP0_SF;
+ for (i = 0; i < ZYNQMP_DISP_AV_BUF_NUM_SF; i++)
+ zynqmp_disp_write(av_buf->base, offset + i * 4,
+ vid_fmt->sf[i]);
+ }
+}
+
+/*
+ * Audio functions
+ */
+
+/**
+ * zynqmp_disp_aud_init - Initialize the audio
+ * @aud: audio
+ *
+ * Initialize the audio with default mixer volume. The de-assertion will
+ * initialize the audio states.
+ */
+static void zynqmp_disp_aud_init(struct zynqmp_disp_aud *aud)
+{
+ /* Clear the audio soft reset register as it's an non-reset flop */
+ zynqmp_disp_write(aud->base, ZYNQMP_DISP_AUD_SOFT_RESET, 0);
+ zynqmp_disp_write(aud->base, ZYNQMP_DISP_AUD_MIXER_VOLUME,
+ ZYNQMP_DISP_AUD_MIXER_VOLUME_NO_SCALE);
+}
+
+/**
+ * zynqmp_disp_aud_deinit - De-initialize the audio
+ * @aud: audio
+ *
+ * Put the audio in reset.
+ */
+static void zynqmp_disp_aud_deinit(struct zynqmp_disp_aud *aud)
+{
+ zynqmp_disp_set(aud->base, ZYNQMP_DISP_AUD_SOFT_RESET,
+ ZYNQMP_DISP_AUD_SOFT_RESET_AUD_SRST);
+}
+
+/*
+ * ZynqMP Display layer functions
+ */
+
+/**
+ * zynqmp_disp_layer_check_size - Verify width and height for the layer
+ * @disp: Display subsystem
+ * @layer: layer
+ * @width: width
+ * @height: height
+ *
+ * The Display subsystem has the limitation that both layers should have
+ * identical size. This function stores width and height of @layer, and verifies
+ * if the size (width and height) is valid.
+ *
+ * Return: 0 on success, or -EINVAL if width or/and height is invalid.
+ */
+static int zynqmp_disp_layer_check_size(struct zynqmp_disp *disp,
+ struct zynqmp_disp_layer *layer,
+ u32 width, u32 height)
+{
+ struct zynqmp_disp_layer *other = layer->other;
+
+ if (other->enabled && (other->w != width || other->h != height)) {
+ dev_err(disp->dev, "Layer width:height must be %d:%d\n",
+ other->w, other->h);
+ return -EINVAL;
+ }
+
+ layer->w = width;
+ layer->h = height;
+
+ return 0;
+}
+
+/**
+ * zynqmp_disp_map_fmt - Find the Display subsystem format for given drm format
+ * @fmts: format table to look up
+ * @size: size of the table @fmts
+ * @drm_fmt: DRM format to search
+ *
+ * Search a Display subsystem format corresponding to the given DRM format
+ * @drm_fmt, and return the format descriptor which contains the Display
+ * subsystem format value.
+ *
+ * Return: a Display subsystem format descriptor on success, or NULL.
+ */
+static const struct zynqmp_disp_fmt *
+zynqmp_disp_map_fmt(const struct zynqmp_disp_fmt fmts[],
+ unsigned int size, uint32_t drm_fmt)
+{
+ unsigned int i;
+
+ for (i = 0; i < size; i++)
+ if (fmts[i].drm_fmt == drm_fmt)
+ return &fmts[i];
+
+ return NULL;
+}
+
+/**
+ * zynqmp_disp_set_fmt - Set the format of the layer
+ * @disp: Display subsystem
+ * @layer: layer to set the format
+ * @drm_fmt: DRM format to set
+ *
+ * Set the format of the given layer to @drm_fmt.
+ *
+ * Return: 0 on success. -EINVAL if @drm_fmt is not supported by the layer.
+ */
+static int zynqmp_disp_layer_set_fmt(struct zynqmp_disp *disp,
+ struct zynqmp_disp_layer *layer,
+ uint32_t drm_fmt)
+{
+ const struct zynqmp_disp_fmt *fmt;
+ const struct zynqmp_disp_fmt *vid_fmt = NULL, *gfx_fmt = NULL;
+ u32 size, fmts, mask;
+
+ if (layer->id == ZYNQMP_DISP_LAYER_VID) {
+ size = ARRAY_SIZE(av_buf_vid_fmts);
+ mask = ~ZYNQMP_DISP_AV_BUF_FMT_NL_VID_MASK;
+ fmt = zynqmp_disp_map_fmt(av_buf_vid_fmts, size, drm_fmt);
+ vid_fmt = fmt;
+ } else {
+ size = ARRAY_SIZE(av_buf_gfx_fmts);
+ mask = ~ZYNQMP_DISP_AV_BUF_FMT_NL_GFX_MASK;
+ fmt = zynqmp_disp_map_fmt(av_buf_gfx_fmts, size, drm_fmt);
+ gfx_fmt = fmt;
+ }
+
+ if (!fmt)
+ return -EINVAL;
+
+ fmts = zynqmp_disp_av_buf_get_fmt(&disp->av_buf);
+ fmts &= mask;
+ fmts |= fmt->disp_fmt;
+ zynqmp_disp_av_buf_set_fmt(&disp->av_buf, fmts);
+ zynqmp_disp_av_buf_init_sf(&disp->av_buf, vid_fmt, gfx_fmt);
+ layer->fmt = fmt;
+
+ return 0;
+}
+
+/**
+ * zynqmp_disp_set_tpg - Enable or disable TPG
+ * @disp: Display subsystem
+ * @layer: Video layer
+ * @tpg_on: flag if TPG needs to be enabled or disabled
+ *
+ * Enable / disable the TPG mode on the video layer @layer depending on
+ * @tpg_on. The video layer should be disabled prior to enable request.
+ *
+ * Return: 0 on success. -ENODEV if it's not video layer. -EIO if
+ * the video layer is enabled.
+ */
+static int zynqmp_disp_layer_set_tpg(struct zynqmp_disp *disp,
+ struct zynqmp_disp_layer *layer,
+ bool tpg_on)
+{
+ if (layer->id != ZYNQMP_DISP_LAYER_VID) {
+ dev_err(disp->dev,
+ "only the video layer has the tpg mode\n");
+ return -ENODEV;
+ }
+
+ if (layer->enabled) {
+ dev_err(disp->dev,
+ "the video layer should be disabled for tpg mode\n");
+ return -EIO;
+ }
+
+ zynqmp_disp_av_buf_set_tpg(&disp->av_buf, tpg_on);
+ disp->tpg_on = tpg_on;
+
+ return 0;
+}
+
+/**
+ * zynqmp_disp_get_fmt - Get the supported DRM formats of the layer
+ * @disp: Display subsystem
+ * @layer: layer to get the formats
+ * @drm_fmts: pointer to array of DRM format strings
+ * @num_fmts: pointer to number of returned DRM formats
+ *
+ * Get the supported DRM formats of the given layer.
+ */
+static void zynqmp_disp_layer_get_fmts(struct zynqmp_disp *disp,
+ struct zynqmp_disp_layer *layer,
+ u32 **drm_fmts, unsigned int *num_fmts)
+{
+ *drm_fmts = layer->drm_fmts;
+ *num_fmts = layer->num_fmts;
+}
+
+/**
+ * zynqmp_disp_layer_enable - Enable the layer
+ * @disp: Display subsystem
+ * @layer: layer to esable
+ * @mode: operation mode
+ *
+ * Enable the layer @layer.
+ *
+ * Return: 0 on success, otherwise error code.
+ */
+static int zynqmp_disp_layer_enable(struct zynqmp_disp *disp,
+ struct zynqmp_disp_layer *layer,
+ enum zynqmp_disp_layer_mode mode)
+{
+ struct device *dev = disp->dev;
+ struct dma_async_tx_descriptor *desc;
+ enum dma_ctrl_flags flags;
+ unsigned int i;
+
+ if (layer->enabled && layer->mode != mode) {
+ dev_err(dev, "layer is already enabled in different mode\n");
+ return -EBUSY;
+ }
+
+ zynqmp_disp_av_buf_enable_vid(&disp->av_buf, layer, mode);
+ zynqmp_disp_blend_layer_enable(&disp->blend, layer);
+
+ layer->enabled = true;
+ layer->mode = mode;
+
+ if (mode == ZYNQMP_DISP_LAYER_LIVE)
+ return 0;
+
+ for (i = 0; i < ZYNQMP_DISP_MAX_NUM_SUB_PLANES; i++) {
+ struct zynqmp_disp_layer_dma *dma = &layer->dma[i];
+
+ if (dma->chan && dma->is_active) {
+ flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
+ desc = dmaengine_prep_interleaved_dma(dma->chan,
+ &dma->xt, flags);
+ if (!desc) {
+ dev_err(dev, "failed to prep DMA descriptor\n");
+ return -ENOMEM;
+ }
+
+ dmaengine_submit(desc);
+ dma_async_issue_pending(dma->chan);
+ }
+ }
+
+ return 0;
+}
+
+/**
+ * zynqmp_disp_layer_disable - Disable the layer
+ * @disp: Display subsystem
+ * @layer: layer to disable
+ * @mode: operation mode
+ *
+ * Disable the layer @layer.
+ *
+ * Return: 0 on success, or -EBUSY if the layer is in different mode.
+ */
+static int zynqmp_disp_layer_disable(struct zynqmp_disp *disp,
+ struct zynqmp_disp_layer *layer,
+ enum zynqmp_disp_layer_mode mode)
+{
+ struct device *dev = disp->dev;
+ unsigned int i;
+
+ if (layer->mode != mode) {
+ dev_err(dev, "the layer is operating in different mode\n");
+ return -EBUSY;
+ }
+
+ for (i = 0; i < ZYNQMP_DISP_MAX_NUM_SUB_PLANES; i++)
+ if (layer->dma[i].chan && layer->dma[i].is_active)
+ dmaengine_terminate_sync(layer->dma[i].chan);
+
+ zynqmp_disp_av_buf_disable_vid(&disp->av_buf, layer);
+ zynqmp_disp_blend_layer_disable(&disp->blend, layer);
+ layer->enabled = false;
+
+ return 0;
+}
+
+/**
+ * zynqmp_disp_layer_request_dma - Request DMA channels for a layer
+ * @disp: Display subsystem
+ * @layer: layer to request DMA channels
+ * @name: identifier string for layer type
+ *
+ * Request DMA engine channels for corresponding layer.
+ *
+ * Return: 0 on success, or err value from of_dma_request_slave_channel().
+ */
+static int
+zynqmp_disp_layer_request_dma(struct zynqmp_disp *disp,
+ struct zynqmp_disp_layer *layer, const char *name)
+{
+ struct zynqmp_disp_layer_dma *dma;
+ unsigned int i;
+ int ret;
+
+ for (i = 0; i < layer->num_chan; i++) {
+ char temp[16];
+
+ dma = &layer->dma[i];
+ snprintf(temp, sizeof(temp), "%s%d", name, i);
+ dma->chan = of_dma_request_slave_channel(layer->of_node,
+ temp);
+ if (IS_ERR(dma->chan)) {
+ dev_err(disp->dev, "failed to request dma channel\n");
+ ret = PTR_ERR(dma->chan);
+ dma->chan = NULL;
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+/**
+ * zynqmp_disp_layer_release_dma - Release DMA channels for a layer
+ * @disp: Display subsystem
+ * @layer: layer to release DMA channels
+ *
+ * Release the dma channels associated with @layer.
+ */
+static void zynqmp_disp_layer_release_dma(struct zynqmp_disp *disp,
+ struct zynqmp_disp_layer *layer)
+{
+ unsigned int i;
+
+ for (i = 0; i < layer->num_chan; i++) {
+ if (layer->dma[i].chan) {
+ /* Make sure the channel is terminated before release */
+ dmaengine_terminate_all(layer->dma[i].chan);
+ dma_release_channel(layer->dma[i].chan);
+ }
+ }
+}
+
+/**
+ * zynqmp_disp_layer_is_live - if any layer is live
+ * @disp: Display subsystem
+ *
+ * Return: true if any layer is live
+ */
+static bool zynqmp_disp_layer_is_live(struct zynqmp_disp *disp)
+{
+ unsigned int i;
+
+ for (i = 0; i < ZYNQMP_DISP_NUM_LAYERS; i++) {
+ if (disp->layers[i].enabled &&
+ disp->layers[i].mode == ZYNQMP_DISP_LAYER_LIVE)
+ return true;
+ }
+
+ return false;
+}
+
+/**
+ * zynqmp_disp_layer_is_enabled - if any layer is enabled
+ * @disp: Display subsystem
+ *
+ * Return: true if any layer is enabled
+ */
+static bool zynqmp_disp_layer_is_enabled(struct zynqmp_disp *disp)
+{
+ unsigned int i;
+
+ for (i = 0; i < ZYNQMP_DISP_NUM_LAYERS; i++)
+ if (disp->layers[i].enabled)
+ return true;
+
+ return false;
+}
+
+/**
+ * zynqmp_disp_layer_destroy - Destroy all layers
+ * @disp: Display subsystem
+ *
+ * Destroy all layers.
+ */
+static void zynqmp_disp_layer_destroy(struct zynqmp_disp *disp)
+{
+ unsigned int i;
+
+ for (i = 0; i < ZYNQMP_DISP_NUM_LAYERS; i++) {
+ zynqmp_disp_layer_release_dma(disp, &disp->layers[i]);
+ if (disp->layers[i].of_node)
+ of_node_put(disp->layers[i].of_node);
+ }
+}
+
+/**
+ * zynqmp_disp_layer_create - Create all layers
+ * @disp: Display subsystem
+ *
+ * Create all layers.
+ *
+ * Return: 0 on success, otherwise error code from failed function
+ */
+static int zynqmp_disp_layer_create(struct zynqmp_disp *disp)
+{
+ struct zynqmp_disp_layer *layer;
+ unsigned int i;
+ int num_chans[ZYNQMP_DISP_NUM_LAYERS] = { 3, 1 };
+ const char * const dma_name[] = { "vid", "gfx" };
+ int ret;
+
+ for (i = 0; i < ZYNQMP_DISP_NUM_LAYERS; i++) {
+ char temp[16];
+
+ layer = &disp->layers[i];
+ layer->id = i;
+ layer->offset = i * 4;
+ layer->other = &disp->layers[!i];
+ layer->num_chan = num_chans[i];
+ snprintf(temp, sizeof(temp), "%s-layer", dma_name[i]);
+ layer->of_node = of_get_child_by_name(disp->dev->of_node, temp);
+ if (!layer->of_node)
+ goto err;
+ ret = zynqmp_disp_layer_request_dma(disp, layer, dma_name[i]);
+ if (ret)
+ goto err;
+ layer->disp = disp;
+ }
+
+ return 0;
+
+err:
+ zynqmp_disp_layer_destroy(disp);
+ return ret;
+}
+
+/*
+ * ZynqMP Display internal functions
+ */
+
+/*
+ * Output format enumeration.
+ * The ID should be aligned with blend_output_fmts.
+ * The string should be aligned with how zynqmp_dp_set_color() decodes.
+ */
+static struct drm_prop_enum_list zynqmp_disp_color_enum[] = {
+ { 0, "rgb" },
+ { 1, "ycrcb444" },
+ { 2, "ycrcb422" },
+ { 3, "yonly" },
+};
+
+/**
+ * zynqmp_disp_set_output_fmt - Set the output format
+ * @disp: Display subsystem
+ * @id: the format ID. Refer to zynqmp_disp_color_enum[].
+ *
+ * This function sets the output format of the display / blender as well as
+ * the format of DP controller. The @id should be aligned with
+ * zynqmp_disp_color_enum.
+ */
+static void
+zynqmp_disp_set_output_fmt(struct zynqmp_disp *disp, unsigned int id)
+{
+ const struct zynqmp_disp_fmt *fmt = &blend_output_fmts[id];
+
+ zynqmp_dp_set_color(disp->dpsub->dp, zynqmp_disp_color_enum[id].name);
+ zynqmp_disp_blend_set_output_fmt(&disp->blend, fmt->disp_fmt);
+}
+
+/**
+ * zynqmp_disp_set_bg_color - Set the background color
+ * @disp: Display subsystem
+ * @c0: color component 0
+ * @c1: color component 1
+ * @c2: color component 2
+ *
+ * Set the background color with given color components (@c0, @c1, @c2).
+ */
+static void zynqmp_disp_set_bg_color(struct zynqmp_disp *disp,
+ u32 c0, u32 c1, u32 c2)
+{
+ zynqmp_disp_blend_set_bg_color(&disp->blend, c0, c1, c2);
+}
+
+/**
+ * zynqmp_disp_set_alpha - Set the alpha value
+ * @disp: Display subsystem
+ * @alpha: alpha value to set
+ *
+ * Set the alpha value for blending.
+ */
+static void zynqmp_disp_set_alpha(struct zynqmp_disp *disp, u32 alpha)
+{
+ disp->alpha = alpha;
+ zynqmp_disp_blend_set_alpha(&disp->blend, alpha);
+}
+
+/**
+ * zynqmp_disp_set_g_alpha - Enable/disable the global alpha blending
+ * @disp: Display subsystem
+ * @enable: flag to enable or disable alpha blending
+ *
+ * Set the alpha value for blending.
+ */
+static void zynqmp_disp_set_g_alpha(struct zynqmp_disp *disp, bool enable)
+{
+ disp->alpha_en = enable;
+ zynqmp_disp_blend_enable_alpha(&disp->blend, enable);
+}
+
+/**
+ * zynqmp_disp_enable - Enable the Display subsystem
+ * @disp: Display subsystem
+ *
+ * Enable the Display subsystem.
+ */
+static void zynqmp_disp_enable(struct zynqmp_disp *disp)
+{
+ bool live;
+
+ if (disp->enabled)
+ return;
+
+ zynqmp_disp_av_buf_enable(&disp->av_buf);
+ /* Choose clock source based on the DT clock handle */
+ zynqmp_disp_av_buf_set_vid_clock_src(&disp->av_buf, !!disp->_ps_pclk);
+ zynqmp_disp_av_buf_set_aud_clock_src(&disp->av_buf, !!disp->_ps_audclk);
+ live = zynqmp_disp_layer_is_live(disp);
+ zynqmp_disp_av_buf_set_vid_timing_src(&disp->av_buf, !live);
+ zynqmp_disp_av_buf_enable_buf(&disp->av_buf);
+ zynqmp_disp_av_buf_enable_aud(&disp->av_buf);
+ zynqmp_disp_aud_init(&disp->aud);
+ disp->enabled = true;
+}
+
+/**
+ * zynqmp_disp_disable - Disable the Display subsystem
+ * @disp: Display subsystem
+ * @force: flag to disable forcefully
+ *
+ * Disable the Display subsystem.
+ */
+static void zynqmp_disp_disable(struct zynqmp_disp *disp, bool force)
+{
+ struct drm_crtc *crtc = &disp->xlnx_crtc.crtc;
+
+ if (!force && (!disp->enabled || zynqmp_disp_layer_is_enabled(disp)))
+ return;
+
+ zynqmp_disp_aud_deinit(&disp->aud);
+ zynqmp_disp_av_buf_disable_aud(&disp->av_buf);
+ zynqmp_disp_av_buf_disable_buf(&disp->av_buf);
+ zynqmp_disp_av_buf_disable(&disp->av_buf);
+
+ /* Mark the flip is done as crtc is disabled anyway */
+ if (crtc->state->event) {
+ complete_all(crtc->state->event->base.completion);
+ crtc->state->event = NULL;
+ }
+
+ disp->enabled = false;
+}
+
+/*
+ * ZynqMP Display external functions for zynqmp_dp
+ */
+
+/**
+ * zynqmp_disp_handle_vblank - Handle the vblank event
+ * @disp: Display subsystem
+ *
+ * This function handles the vblank interrupt, and sends an event to
+ * CRTC object. This will be called by the DP vblank interrupt handler.
+ */
+void zynqmp_disp_handle_vblank(struct zynqmp_disp *disp)
+{
+ struct drm_crtc *crtc = &disp->xlnx_crtc.crtc;
+
+ drm_crtc_handle_vblank(crtc);
+}
+
+/**
+ * zynqmp_disp_get_apb_clk_rate - Get the current APB clock rate
+ * @disp: Display subsystem
+ *
+ * Return: the current APB clock rate.
+ */
+unsigned int zynqmp_disp_get_apb_clk_rate(struct zynqmp_disp *disp)
+{
+ return clk_get_rate(disp->aclk);
+}
+
+/**
+ * zynqmp_disp_aud_enabled - If the audio is enabled
+ * @disp: Display subsystem
+ *
+ * Return if the audio is enabled depending on the audio clock.
+ *
+ * Return: true if audio is enabled, or false.
+ */
+bool zynqmp_disp_aud_enabled(struct zynqmp_disp *disp)
+{
+ return !!disp->audclk;
+}
+
+/**
+ * zynqmp_disp_get_aud_clk_rate - Get the current audio clock rate
+ * @disp: Display subsystem
+ *
+ * Return: the current audio clock rate.
+ */
+unsigned int zynqmp_disp_get_aud_clk_rate(struct zynqmp_disp *disp)
+{
+ if (zynqmp_disp_aud_enabled(disp))
+ return 0;
+ return clk_get_rate(disp->aclk);
+}
+
+/**
+ * zynqmp_disp_get_crtc_mask - Return the CRTC bit mask
+ * @disp: Display subsystem
+ *
+ * Return: the crtc mask of the zyqnmp_disp CRTC.
+ */
+uint32_t zynqmp_disp_get_crtc_mask(struct zynqmp_disp *disp)
+{
+ return drm_crtc_mask(&disp->xlnx_crtc.crtc);
+}
+
+/*
+ * DRM plane functions
+ */
+
+static inline struct zynqmp_disp_layer *plane_to_layer(struct drm_plane *plane)
+{
+ return container_of(plane, struct zynqmp_disp_layer, plane);
+}
+
+static int zynqmp_disp_plane_enable(struct drm_plane *plane)
+{
+ struct zynqmp_disp_layer *layer = plane_to_layer(plane);
+ struct zynqmp_disp *disp = layer->disp;
+ int ret;
+
+ zynqmp_disp_set_g_alpha(disp, disp->alpha_en);
+ zynqmp_disp_set_alpha(disp, disp->alpha);
+ ret = zynqmp_disp_layer_enable(layer->disp, layer,
+ ZYNQMP_DISP_LAYER_NONLIVE);
+ if (ret)
+ return ret;
+
+ if (layer->id == ZYNQMP_DISP_LAYER_GFX && disp->tpg_on) {
+ layer = &disp->layers[ZYNQMP_DISP_LAYER_VID];
+ zynqmp_disp_layer_set_tpg(disp, layer, disp->tpg_on);
+ }
+
+ return 0;
+}
+
+static int zynqmp_disp_plane_disable(struct drm_plane *plane)
+{
+ struct zynqmp_disp_layer *layer = plane_to_layer(plane);
+ struct zynqmp_disp *disp = layer->disp;
+
+ zynqmp_disp_layer_disable(disp, layer, ZYNQMP_DISP_LAYER_NONLIVE);
+ if (layer->id == ZYNQMP_DISP_LAYER_VID && disp->tpg_on)
+ zynqmp_disp_layer_set_tpg(disp, layer, disp->tpg_on);
+
+ return 0;
+}
+
+static int zynqmp_disp_plane_mode_set(struct drm_plane *plane,
+ struct drm_framebuffer *fb,
+ int crtc_x, int crtc_y,
+ unsigned int crtc_w, unsigned int crtc_h,
+ u32 src_x, u32 src_y,
+ u32 src_w, u32 src_h)
+{
+ struct zynqmp_disp_layer *layer = plane_to_layer(plane);
+ const struct drm_format_info *info = fb->format;
+ struct drm_format_name_buf format_name;
+ struct device *dev = layer->disp->dev;
+ dma_addr_t paddr;
+ unsigned int i;
+ int ret;
+
+ if (!info) {
+ dev_err(dev, "unsupported framebuffer format %s\n",
+ drm_get_format_name(info->format, &format_name));
+ return -EINVAL;
+ }
+
+ ret = zynqmp_disp_layer_check_size(layer->disp, layer, src_w, src_h);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < info->num_planes; i++) {
+ unsigned int width = src_w / (i ? info->hsub : 1);
+ unsigned int height = src_h / (i ? info->vsub : 1);
+
+ paddr = drm_fb_cma_get_gem_addr(fb, plane->state, i);
+ if (!paddr) {
+ dev_err(dev, "failed to get a paddr\n");
+ return -EINVAL;
+ }
+
+ layer->dma[i].xt.numf = height;
+ layer->dma[i].sgl[0].size = width * info->cpp[i];
+ layer->dma[i].sgl[0].icg = fb->pitches[i] -
+ layer->dma[i].sgl[0].size;
+ layer->dma[i].xt.src_start = paddr;
+ layer->dma[i].xt.frame_size = 1;
+ layer->dma[i].xt.dir = DMA_MEM_TO_DEV;
+ layer->dma[i].xt.src_sgl = true;
+ layer->dma[i].xt.dst_sgl = false;
+ layer->dma[i].is_active = true;
+ }
+
+ for (; i < ZYNQMP_DISP_MAX_NUM_SUB_PLANES; i++)
+ layer->dma[i].is_active = false;
+
+ ret = zynqmp_disp_layer_set_fmt(layer->disp, layer, info->format);
+ if (ret)
+ dev_err(dev, "failed to set dp_sub layer fmt\n");
+
+ return ret;
+}
+
+static void zynqmp_disp_plane_destroy(struct drm_plane *plane)
+{
+ drm_plane_cleanup(plane);
+}
+
+static struct drm_plane_funcs zynqmp_disp_plane_funcs = {
+ .update_plane = drm_atomic_helper_update_plane,
+ .disable_plane = drm_atomic_helper_disable_plane,
+ .destroy = zynqmp_disp_plane_destroy,
+ .reset = drm_atomic_helper_plane_reset,
+ .atomic_duplicate_state = drm_atomic_helper_plane_duplicate_state,
+ .atomic_destroy_state = drm_atomic_helper_plane_destroy_state,
+};
+
+static void
+zynqmp_disp_plane_atomic_update(struct drm_plane *plane,
+ struct drm_plane_state *old_state)
+{
+ int ret;
+
+ if (!plane->state->crtc || !plane->state->fb)
+ return;
+
+ ret = zynqmp_disp_plane_mode_set(plane, plane->state->fb,
+ plane->state->crtc_x,
+ plane->state->crtc_y,
+ plane->state->crtc_w,
+ plane->state->crtc_h,
+ plane->state->src_x >> 16,
+ plane->state->src_y >> 16,
+ plane->state->src_w >> 16,
+ plane->state->src_h >> 16);
+ if (ret)
+ return;
+
+ zynqmp_disp_plane_enable(plane);
+}
+
+static void
+zynqmp_disp_plane_atomic_disable(struct drm_plane *plane,
+ struct drm_plane_state *old_state)
+{
+ zynqmp_disp_plane_disable(plane);
+}
+
+static const struct drm_plane_helper_funcs zynqmp_disp_plane_helper_funcs = {
+ .atomic_update = zynqmp_disp_plane_atomic_update,
+ .atomic_disable = zynqmp_disp_plane_atomic_disable,
+};
+
+static int zynqmp_disp_create_plane(struct zynqmp_disp *disp)
+{
+ struct zynqmp_disp_layer *layer;
+ unsigned int i;
+ u32 *fmts = NULL;
+ unsigned int num_fmts = 0;
+ enum drm_plane_type type;
+ int ret;
+
+ /* graphics layer is primary, and video layer is overaly */
+ type = DRM_PLANE_TYPE_OVERLAY;
+ for (i = 0; i < ZYNQMP_DISP_NUM_LAYERS; i++) {
+ layer = &disp->layers[i];
+ zynqmp_disp_layer_get_fmts(disp, layer, &fmts, &num_fmts);
+ ret = drm_universal_plane_init(disp->drm, &layer->plane, 0,
+ &zynqmp_disp_plane_funcs, fmts,
+ num_fmts, NULL, type, NULL);
+ if (ret)
+ goto err_plane;
+ drm_plane_helper_add(&layer->plane,
+ &zynqmp_disp_plane_helper_funcs);
+ type = DRM_PLANE_TYPE_PRIMARY;
+ }
+
+ return ret;
+
+err_plane:
+ if (i)
+ drm_plane_cleanup(&disp->layers[0].plane);
+ return ret;
+}
+
+static void zynqmp_disp_destroy_plane(struct zynqmp_disp *disp)
+{
+ unsigned int i;
+
+ for (i = 0; i < ZYNQMP_DISP_NUM_LAYERS; i++)
+ zynqmp_disp_plane_destroy(&disp->layers[i].plane);
+}
+
+/*
+ * Xlnx crtc functions
+ */
+
+static inline struct zynqmp_disp *xlnx_crtc_to_disp(struct xlnx_crtc *xlnx_crtc)
+{
+ return container_of(xlnx_crtc, struct zynqmp_disp, xlnx_crtc);
+}
+
+static int zynqmp_disp_enable_vblank(struct xlnx_crtc *xlnx_crtc)
+{
+ struct zynqmp_disp *disp = xlnx_crtc_to_disp(xlnx_crtc);
+
+ zynqmp_dp_enable_vblank(disp->dpsub->dp);
+ return 0;
+}
+
+static void zynqmp_disp_disable_vblank(struct xlnx_crtc *xlnx_crtc)
+{
+ struct zynqmp_disp *disp = xlnx_crtc_to_disp(xlnx_crtc);
+
+ zynqmp_dp_disable_vblank(disp->dpsub->dp);
+}
+
+static int zynqmp_disp_get_max_width(struct xlnx_crtc *xlnx_crtc)
+{
+ return ZYNQMP_DISP_MAX_WIDTH;
+}
+
+static int zynqmp_disp_get_max_height(struct xlnx_crtc *xlnx_crtc)
+{
+ return ZYNQMP_DISP_MAX_HEIGHT;
+}
+
+static uint32_t zynqmp_disp_get_format(struct xlnx_crtc *xlnx_crtc)
+{
+ struct zynqmp_disp *disp = xlnx_crtc_to_disp(xlnx_crtc);
+
+ return disp->layers[ZYNQMP_DISP_LAYER_GFX].fmt->drm_fmt;
+}
+
+static unsigned int zynqmp_disp_get_align(struct xlnx_crtc *xlnx_crtc)
+{
+ struct zynqmp_disp *disp = xlnx_crtc_to_disp(xlnx_crtc);
+ struct zynqmp_disp_layer *layer = &disp->layers[ZYNQMP_DISP_LAYER_VID];
+
+ return 1 << layer->dma->chan->device->copy_align;
+}
+
+static u64 zynqmp_disp_get_dma_mask(struct xlnx_crtc *xlnx_crtc)
+{
+ return DMA_BIT_MASK(ZYNQMP_DISP_MAX_DMA_BIT);
+}
+
+/*
+ * DRM crtc functions
+ */
+
+static inline struct zynqmp_disp *crtc_to_disp(struct drm_crtc *crtc)
+{
+ struct xlnx_crtc *xlnx_crtc = to_xlnx_crtc(crtc);
+
+ return xlnx_crtc_to_disp(xlnx_crtc);
+}
+
+static int zynqmp_disp_crtc_mode_set(struct drm_crtc *crtc,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode,
+ int x, int y,
+ struct drm_framebuffer *old_fb)
+{
+ struct zynqmp_disp *disp = crtc_to_disp(crtc);
+ unsigned long rate;
+ long diff;
+ int ret;
+
+ zynqmp_disp_clk_disable(disp->pclk, &disp->pclk_en);
+ ret = clk_set_rate(disp->pclk, adjusted_mode->clock * 1000);
+ if (ret) {
+ dev_err(disp->dev, "failed to set a pixel clock\n");
+ return ret;
+ }
+
+ rate = clk_get_rate(disp->pclk);
+ diff = rate - adjusted_mode->clock * 1000;
+ if (abs(diff) > (adjusted_mode->clock * 1000) / 20) {
+ dev_info(disp->dev, "request pixel rate: %d actual rate: %lu\n",
+ adjusted_mode->clock, rate);
+ } else {
+ dev_dbg(disp->dev, "request pixel rate: %d actual rate: %lu\n",
+ adjusted_mode->clock, rate);
+ }
+
+ /* The timing register should be programmed always */
+ zynqmp_dp_encoder_mode_set_stream(disp->dpsub->dp, adjusted_mode);
+
+ return 0;
+}
+
+static void
+zynqmp_disp_crtc_atomic_enable(struct drm_crtc *crtc,
+ struct drm_crtc_state *old_crtc_state)
+{
+ struct zynqmp_disp *disp = crtc_to_disp(crtc);
+ struct drm_display_mode *adjusted_mode = &crtc->state->adjusted_mode;
+ int ret, vrefresh;
+
+ zynqmp_disp_crtc_mode_set(crtc, &crtc->state->mode,
+ adjusted_mode, crtc->x, crtc->y, NULL);
+
+ pm_runtime_get_sync(disp->dev);
+ ret = zynqmp_disp_clk_enable(disp->pclk, &disp->pclk_en);
+ if (ret) {
+ dev_err(disp->dev, "failed to enable a pixel clock\n");
+ return;
+ }
+ zynqmp_disp_set_output_fmt(disp, disp->color);
+ zynqmp_disp_set_bg_color(disp, disp->bg_c0, disp->bg_c1, disp->bg_c2);
+ zynqmp_disp_enable(disp);
+ /* Delay of 3 vblank intervals for timing gen to be stable */
+ vrefresh = (adjusted_mode->clock * 1000) /
+ (adjusted_mode->vtotal * adjusted_mode->htotal);
+ msleep(3 * 1000 / vrefresh);
+}
+
+static void
+zynqmp_disp_crtc_atomic_disable(struct drm_crtc *crtc,
+ struct drm_crtc_state *old_crtc_state)
+{
+ struct zynqmp_disp *disp = crtc_to_disp(crtc);
+
+ zynqmp_disp_clk_disable(disp->pclk, &disp->pclk_en);
+ zynqmp_disp_plane_disable(crtc->primary);
+ zynqmp_disp_disable(disp, true);
+ pm_runtime_put_sync(disp->dev);
+}
+
+static int zynqmp_disp_crtc_atomic_check(struct drm_crtc *crtc,
+ struct drm_crtc_state *state)
+{
+ return drm_atomic_add_affected_planes(state->state, crtc);
+}
+
+static void
+zynqmp_disp_crtc_atomic_begin(struct drm_crtc *crtc,
+ struct drm_crtc_state *old_crtc_state)
+{
+ /* Don't rely on vblank when disabling crtc */
+ spin_lock_irq(&crtc->dev->event_lock);
+ if (crtc->primary->state->fb && crtc->state->event) {
+ /* Consume the flip_done event from atomic helper */
+ crtc->state->event->pipe = drm_crtc_index(crtc);
+ WARN_ON(drm_crtc_vblank_get(crtc) != 0);
+ drm_crtc_arm_vblank_event(crtc, crtc->state->event);
+ crtc->state->event = NULL;
+ }
+ spin_unlock_irq(&crtc->dev->event_lock);
+}
+
+static struct drm_crtc_helper_funcs zynqmp_disp_crtc_helper_funcs = {
+ .atomic_enable = zynqmp_disp_crtc_atomic_enable,
+ .atomic_disable = zynqmp_disp_crtc_atomic_disable,
+ .atomic_check = zynqmp_disp_crtc_atomic_check,
+ .atomic_begin = zynqmp_disp_crtc_atomic_begin,
+};
+
+static void zynqmp_disp_crtc_destroy(struct drm_crtc *crtc)
+{
+ zynqmp_disp_crtc_atomic_disable(crtc, NULL);
+ drm_crtc_cleanup(crtc);
+}
+
+static struct drm_crtc_funcs zynqmp_disp_crtc_funcs = {
+ .destroy = zynqmp_disp_crtc_destroy,
+ .set_config = drm_atomic_helper_set_config,
+ .page_flip = drm_atomic_helper_page_flip,
+ .reset = drm_atomic_helper_crtc_reset,
+ .atomic_duplicate_state = drm_atomic_helper_crtc_duplicate_state,
+ .atomic_destroy_state = drm_atomic_helper_crtc_destroy_state,
+};
+
+static void zynqmp_disp_create_crtc(struct zynqmp_disp *disp)
+{
+ struct drm_plane *plane = &disp->layers[ZYNQMP_DISP_LAYER_GFX].plane;
+ int ret;
+
+ ret = drm_crtc_init_with_planes(disp->drm, &disp->xlnx_crtc.crtc, plane,
+ NULL, &zynqmp_disp_crtc_funcs, NULL);
+ drm_crtc_helper_add(&disp->xlnx_crtc.crtc,
+ &zynqmp_disp_crtc_helper_funcs);
+
+ disp->xlnx_crtc.enable_vblank = &zynqmp_disp_enable_vblank;
+ disp->xlnx_crtc.disable_vblank = &zynqmp_disp_disable_vblank;
+ disp->xlnx_crtc.get_max_width = &zynqmp_disp_get_max_width;
+ disp->xlnx_crtc.get_max_height = &zynqmp_disp_get_max_height;
+ disp->xlnx_crtc.get_format = &zynqmp_disp_get_format;
+ disp->xlnx_crtc.get_align = &zynqmp_disp_get_align;
+ disp->xlnx_crtc.get_dma_mask = &zynqmp_disp_get_dma_mask;
+ xlnx_crtc_register(disp->drm, &disp->xlnx_crtc);
+}
+
+static void zynqmp_disp_destroy_crtc(struct zynqmp_disp *disp)
+{
+ xlnx_crtc_unregister(disp->drm, &disp->xlnx_crtc);
+ zynqmp_disp_crtc_destroy(&disp->xlnx_crtc.crtc);
+}
+
+static void zynqmp_disp_map_crtc_to_plane(struct zynqmp_disp *disp)
+{
+ u32 possible_crtcs = drm_crtc_mask(&disp->xlnx_crtc.crtc);
+ unsigned int i;
+
+ for (i = 0; i < ZYNQMP_DISP_NUM_LAYERS; i++)
+ disp->layers[i].plane.possible_crtcs = possible_crtcs;
+}
+
+/*
+ * Component functions
+ */
+
+int zynqmp_disp_bind(struct device *dev, struct device *master, void *data)
+{
+ struct zynqmp_dpsub *dpsub = dev_get_drvdata(dev);
+ struct zynqmp_disp *disp = dpsub->disp;
+ struct drm_device *drm = data;
+ int ret;
+
+ disp->drm = drm;
+
+ ret = zynqmp_disp_create_plane(disp);
+ if (ret)
+ return ret;
+ zynqmp_disp_create_crtc(disp);
+ zynqmp_disp_map_crtc_to_plane(disp);
+
+ return 0;
+}
+
+void zynqmp_disp_unbind(struct device *dev, struct device *master, void *data)
+{
+ struct zynqmp_dpsub *dpsub = dev_get_drvdata(dev);
+ struct zynqmp_disp *disp = dpsub->disp;
+
+ zynqmp_disp_destroy_crtc(disp);
+ zynqmp_disp_destroy_plane(disp);
+}
+
+/*
+ * Platform initialization functions
+ */
+
+static int zynqmp_disp_enumerate_fmts(struct zynqmp_disp *disp)
+{
+ struct zynqmp_disp_layer *layer;
+ u32 *bus_fmts;
+ u32 i, size, num_bus_fmts;
+
+ num_bus_fmts = ARRAY_SIZE(av_buf_live_fmts);
+ bus_fmts = devm_kzalloc(disp->dev, sizeof(*bus_fmts) * num_bus_fmts,
+ GFP_KERNEL);
+ if (!bus_fmts)
+ return -ENOMEM;
+ for (i = 0; i < num_bus_fmts; i++)
+ bus_fmts[i] = av_buf_live_fmts[i].bus_fmt;
+
+ layer = &disp->layers[ZYNQMP_DISP_LAYER_VID];
+ layer->num_bus_fmts = num_bus_fmts;
+ layer->bus_fmts = bus_fmts;
+ size = ARRAY_SIZE(av_buf_vid_fmts);
+ layer->num_fmts = size;
+ layer->drm_fmts = devm_kzalloc(disp->dev,
+ sizeof(*layer->drm_fmts) * size,
+ GFP_KERNEL);
+ if (!layer->drm_fmts)
+ return -ENOMEM;
+ for (i = 0; i < layer->num_fmts; i++)
+ layer->drm_fmts[i] = av_buf_vid_fmts[i].drm_fmt;
+ layer->fmt = &av_buf_vid_fmts[ZYNQMP_DISP_AV_BUF_VID_FMT_YUYV];
+
+ layer = &disp->layers[ZYNQMP_DISP_LAYER_GFX];
+ layer->num_bus_fmts = num_bus_fmts;
+ layer->bus_fmts = bus_fmts;
+ size = ARRAY_SIZE(av_buf_gfx_fmts);
+ layer->num_fmts = size;
+ layer->drm_fmts = devm_kzalloc(disp->dev,
+ sizeof(*layer->drm_fmts) * size,
+ GFP_KERNEL);
+ if (!layer->drm_fmts)
+ return -ENOMEM;
+
+ for (i = 0; i < layer->num_fmts; i++)
+ layer->drm_fmts[i] = av_buf_gfx_fmts[i].drm_fmt;
+ layer->fmt = &av_buf_gfx_fmts[ZYNQMP_DISP_AV_BUF_GFX_FMT_RGB565];
+
+ return 0;
+}
+
+int zynqmp_disp_probe(struct platform_device *pdev)
+{
+ struct zynqmp_dpsub *dpsub;
+ struct zynqmp_disp *disp;
+ struct resource *res;
+ int ret;
+
+ disp = devm_kzalloc(&pdev->dev, sizeof(*disp), GFP_KERNEL);
+ if (!disp)
+ return -ENOMEM;
+ disp->dev = &pdev->dev;
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "blend");
+ disp->blend.base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(disp->blend.base))
+ return PTR_ERR(disp->blend.base);
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "av_buf");
+ disp->av_buf.base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(disp->av_buf.base))
+ return PTR_ERR(disp->av_buf.base);
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "aud");
+ disp->aud.base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(disp->aud.base))
+ return PTR_ERR(disp->aud.base);
+
+ dpsub = platform_get_drvdata(pdev);
+ dpsub->disp = disp;
+ disp->dpsub = dpsub;
+
+ ret = zynqmp_disp_enumerate_fmts(disp);
+ if (ret)
+ return ret;
+
+ /* Try the live PL video clock */
+ disp->_pl_pclk = devm_clk_get(disp->dev, "dp_live_video_in_clk");
+ if (!IS_ERR(disp->_pl_pclk)) {
+ disp->pclk = disp->_pl_pclk;
+ ret = zynqmp_disp_clk_enable_disable(disp->pclk,
+ &disp->pclk_en);
+ if (ret)
+ disp->pclk = NULL;
+ } else if (PTR_ERR(disp->_pl_pclk) == -EPROBE_DEFER) {
+ return PTR_ERR(disp->_pl_pclk);
+ }
+
+ /* If the live PL video clock is not valid, fall back to PS clock */
+ if (!disp->pclk) {
+ disp->_ps_pclk = devm_clk_get(disp->dev, "dp_vtc_pixel_clk_in");
+ if (IS_ERR(disp->_ps_pclk)) {
+ dev_err(disp->dev, "failed to init any video clock\n");
+ return PTR_ERR(disp->_ps_pclk);
+ }
+ disp->pclk = disp->_ps_pclk;
+ ret = zynqmp_disp_clk_enable_disable(disp->pclk,
+ &disp->pclk_en);
+ if (ret) {
+ dev_err(disp->dev, "failed to init any video clock\n");
+ return ret;
+ }
+ }
+
+ disp->aclk = devm_clk_get(disp->dev, "dp_apb_clk");
+ if (IS_ERR(disp->aclk))
+ return PTR_ERR(disp->aclk);
+ ret = zynqmp_disp_clk_enable(disp->aclk, &disp->aclk_en);
+ if (ret) {
+ dev_err(disp->dev, "failed to enable the APB clk\n");
+ return ret;
+ }
+
+ /* Try the live PL audio clock */
+ disp->_pl_audclk = devm_clk_get(disp->dev, "dp_live_audio_aclk");
+ if (!IS_ERR(disp->_pl_audclk)) {
+ disp->audclk = disp->_pl_audclk;
+ ret = zynqmp_disp_clk_enable_disable(disp->audclk,
+ &disp->audclk_en);
+ if (ret)
+ disp->audclk = NULL;
+ }
+
+ /* If the live PL audio clock is not valid, fall back to PS clock */
+ if (!disp->audclk) {
+ disp->_ps_audclk = devm_clk_get(disp->dev, "dp_aud_clk");
+ if (!IS_ERR(disp->_ps_audclk)) {
+ disp->audclk = disp->_ps_audclk;
+ ret = zynqmp_disp_clk_enable_disable(disp->audclk,
+ &disp->audclk_en);
+ if (ret)
+ disp->audclk = NULL;
+ }
+
+ if (!disp->audclk) {
+ dev_err(disp->dev,
+ "audio is disabled due to clock failure\n");
+ }
+ }
+
+ ret = zynqmp_disp_layer_create(disp);
+ if (ret)
+ goto error_aclk;
+
+ return 0;
+
+error_aclk:
+ zynqmp_disp_clk_disable(disp->aclk, &disp->aclk_en);
+ return ret;
+}
+
+int zynqmp_disp_remove(struct platform_device *pdev)
+{
+ struct zynqmp_dpsub *dpsub = platform_get_drvdata(pdev);
+ struct zynqmp_disp *disp = dpsub->disp;
+
+ zynqmp_disp_layer_destroy(disp);
+ if (disp->audclk)
+ zynqmp_disp_clk_disable(disp->audclk, &disp->audclk_en);
+ zynqmp_disp_clk_disable(disp->aclk, &disp->aclk_en);
+ zynqmp_disp_clk_disable(disp->pclk, &disp->pclk_en);
+ dpsub->disp = NULL;
+
+ return 0;
+}
diff --git a/drivers/gpu/drm/xlnx/zynqmp_disp.h b/drivers/gpu/drm/xlnx/zynqmp_disp.h
new file mode 100644
index 0000000..28d8188
--- /dev/null
+++ b/drivers/gpu/drm/xlnx/zynqmp_disp.h
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ZynqMP Display Driver
+ *
+ * Copyright (C) 2017 - 2018 Xilinx, Inc.
+ *
+ * Author: Hyun Woo Kwon <hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _ZYNQMP_DISP_H_
+#define _ZYNQMP_DISP_H_
+
+struct zynqmp_disp;
+
+void zynqmp_disp_handle_vblank(struct zynqmp_disp *disp);
+unsigned int zynqmp_disp_get_apb_clk_rate(struct zynqmp_disp *disp);
+bool zynqmp_disp_aud_enabled(struct zynqmp_disp *disp);
+unsigned int zynqmp_disp_get_aud_clk_rate(struct zynqmp_disp *disp);
+uint32_t zynqmp_disp_get_crtc_mask(struct zynqmp_disp *disp);
+
+int zynqmp_disp_bind(struct device *dev, struct device *master, void *data);
+void zynqmp_disp_unbind(struct device *dev, struct device *master, void *data);
+
+int zynqmp_disp_probe(struct platform_device *pdev);
+int zynqmp_disp_remove(struct platform_device *pdev);
+
+#endif /* _ZYNQMP_DISP_H_ */
--
2.7.4
This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH v3 5/8] drm: xlnx: DRM KMS driver for Xilinx ZynqMP DisplayPort
[not found] ` <1516067831-11382-1-git-send-email-hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
` (2 preceding siblings ...)
2018-01-16 1:57 ` [PATCH v3 4/8] drm: xlnx: DRM KMS driver for Xilinx ZynqMP DP subsystem display Hyun Kwon
@ 2018-01-16 1:57 ` Hyun Kwon
2018-01-16 1:57 ` [PATCH v3 6/8] drm: xlnx: ZynqMP DP subsystem DRM KMS driver Hyun Kwon
4 siblings, 0 replies; 17+ messages in thread
From: Hyun Kwon @ 2018-01-16 1:57 UTC (permalink / raw)
To: dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW,
devicetree-u79uwXL29TY76Z2rM5mHXA
Cc: Michal Simek, Rob Herring, Daniel Vetter, Laurent Pinchart, Hyun Kwon
This driver creates DRM encoder and connector for ZynqMP DisplayPort.
Signed-off-by: Hyun Kwon <hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
---
v2
- Change the SPDX identifier format
- Split drm properties into a separate patch
---
---
drivers/gpu/drm/xlnx/zynqmp_dp.c | 1738 ++++++++++++++++++++++++++++++++++++++
drivers/gpu/drm/xlnx/zynqmp_dp.h | 37 +
2 files changed, 1775 insertions(+)
create mode 100644 drivers/gpu/drm/xlnx/zynqmp_dp.c
create mode 100644 drivers/gpu/drm/xlnx/zynqmp_dp.h
diff --git a/drivers/gpu/drm/xlnx/zynqmp_dp.c b/drivers/gpu/drm/xlnx/zynqmp_dp.c
new file mode 100644
index 0000000..9c9f4df
--- /dev/null
+++ b/drivers/gpu/drm/xlnx/zynqmp_dp.c
@@ -0,0 +1,1738 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ZynqMP DisplayPort Driver
+ *
+ * Copyright (C) 2017 - 2018 Xilinx, Inc.
+ *
+ * Author: Hyun Woo Kwon <hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <drm/drmP.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_connector.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_dp_helper.h>
+#include <drm/drm_of.h>
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/uaccess.h>
+
+#include "zynqmp_disp.h"
+#include "zynqmp_dpsub.h"
+
+static uint zynqmp_dp_aux_timeout_ms = 50;
+module_param_named(aux_timeout_ms, zynqmp_dp_aux_timeout_ms, uint, 0444);
+MODULE_PARM_DESC(aux_timeout_ms, "DP aux timeout value in msec (default: 50)");
+
+/*
+ * Some sink requires a delay after power on request
+ */
+static uint zynqmp_dp_power_on_delay_ms = 4;
+module_param_named(power_on_delay_ms, zynqmp_dp_power_on_delay_ms, uint, 0444);
+MODULE_PARM_DESC(aux_timeout_ms, "DP power on delay in msec (default: 4)");
+
+/* Link configuration registers */
+#define ZYNQMP_DP_TX_LINK_BW_SET 0x0
+#define ZYNQMP_DP_TX_LANE_CNT_SET 0x4
+#define ZYNQMP_DP_TX_ENHANCED_FRAME_EN 0x8
+#define ZYNQMP_DP_TX_TRAINING_PATTERN_SET 0xc
+#define ZYNQMP_DP_TX_SCRAMBLING_DISABLE 0x14
+#define ZYNQMP_DP_TX_DOWNSPREAD_CTL 0x18
+#define ZYNQMP_DP_TX_SW_RESET 0x1c
+#define ZYNQMP_DP_TX_SW_RESET_STREAM1 BIT(0)
+#define ZYNQMP_DP_TX_SW_RESET_STREAM2 BIT(1)
+#define ZYNQMP_DP_TX_SW_RESET_STREAM3 BIT(2)
+#define ZYNQMP_DP_TX_SW_RESET_STREAM4 BIT(3)
+#define ZYNQMP_DP_TX_SW_RESET_AUX BIT(7)
+#define ZYNQMP_DP_TX_SW_RESET_ALL (ZYNQMP_DP_TX_SW_RESET_STREAM1 | \
+ ZYNQMP_DP_TX_SW_RESET_STREAM2 | \
+ ZYNQMP_DP_TX_SW_RESET_STREAM3 | \
+ ZYNQMP_DP_TX_SW_RESET_STREAM4 | \
+ ZYNQMP_DP_TX_SW_RESET_AUX)
+
+/* Core enable registers */
+#define ZYNQMP_DP_TX_ENABLE 0x80
+#define ZYNQMP_DP_TX_ENABLE_MAIN_STREAM 0x84
+#define ZYNQMP_DP_TX_FORCE_SCRAMBLER_RESET 0xc0
+#define ZYNQMP_DP_TX_VERSION 0xf8
+#define ZYNQMP_DP_TX_VERSION_MAJOR_MASK GENMASK(31, 24)
+#define ZYNQMP_DP_TX_VERSION_MAJOR_SHIFT 24
+#define ZYNQMP_DP_TX_VERSION_MINOR_MASK GENMASK(23, 16)
+#define ZYNQMP_DP_TX_VERSION_MINOR_SHIFT 16
+#define ZYNQMP_DP_TX_VERSION_REVISION_MASK GENMASK(15, 12)
+#define ZYNQMP_DP_TX_VERSION_REVISION_SHIFT 12
+#define ZYNQMP_DP_TX_VERSION_PATCH_MASK GENMASK(11, 8)
+#define ZYNQMP_DP_TX_VERSION_PATCH_SHIFT 8
+#define ZYNQMP_DP_TX_VERSION_INTERNAL_MASK GENMASK(7, 0)
+#define ZYNQMP_DP_TX_VERSION_INTERNAL_SHIFT 0
+
+/* Core ID registers */
+#define ZYNQMP_DP_TX_CORE_ID 0xfc
+#define ZYNQMP_DP_TX_CORE_ID_MAJOR_MASK GENMASK(31, 24)
+#define ZYNQMP_DP_TX_CORE_ID_MAJOR_SHIFT 24
+#define ZYNQMP_DP_TX_CORE_ID_MINOR_MASK GENMASK(23, 16)
+#define ZYNQMP_DP_TX_CORE_ID_MINOR_SHIFT 16
+#define ZYNQMP_DP_TX_CORE_ID_REVISION_MASK GENMASK(15, 8)
+#define ZYNQMP_DP_TX_CORE_ID_REVISION_SHIFT 8
+#define ZYNQMP_DP_TX_CORE_ID_DIRECTION GENMASK(1)
+
+/* AUX channel interface registers */
+#define ZYNQMP_DP_TX_AUX_COMMAND 0x100
+#define ZYNQMP_DP_TX_AUX_COMMAND_CMD_SHIFT 8
+#define ZYNQMP_DP_TX_AUX_COMMAND_ADDRESS_ONLY BIT(12)
+#define ZYNQMP_DP_TX_AUX_COMMAND_BYTES_SHIFT 0
+#define ZYNQMP_DP_TX_AUX_WRITE_FIFO 0x104
+#define ZYNQMP_DP_TX_AUX_ADDRESS 0x108
+#define ZYNQMP_DP_TX_CLK_DIVIDER 0x10c
+#define ZYNQMP_DP_TX_CLK_DIVIDER_MHZ 1000000
+#define ZYNQMP_DP_TX_CLK_DIVIDER_AUX_FILTER_SHIFT 8
+#define ZYNQMP_DP_TX_INTR_SIGNAL_STATE 0x130
+#define ZYNQMP_DP_TX_INTR_SIGNAL_STATE_HPD BIT(0)
+#define ZYNQMP_DP_TX_INTR_SIGNAL_STATE_REQUEST BIT(1)
+#define ZYNQMP_DP_TX_INTR_SIGNAL_STATE_REPLY BIT(2)
+#define ZYNQMP_DP_TX_INTR_SIGNAL_STATE_REPLY_TIMEOUT BIT(3)
+#define ZYNQMP_DP_TX_AUX_REPLY_DATA 0x134
+#define ZYNQMP_DP_TX_AUX_REPLY_CODE 0x138
+#define ZYNQMP_DP_TX_AUX_REPLY_CODE_AUX_ACK (0)
+#define ZYNQMP_DP_TX_AUX_REPLY_CODE_AUX_NACK BIT(0)
+#define ZYNQMP_DP_TX_AUX_REPLY_CODE_AUX_DEFER BIT(1)
+#define ZYNQMP_DP_TX_AUX_REPLY_CODE_I2C_ACK (0)
+#define ZYNQMP_DP_TX_AUX_REPLY_CODE_I2C_NACK BIT(2)
+#define ZYNQMP_DP_TX_AUX_REPLY_CODE_I2C_DEFER BIT(3)
+#define ZYNQMP_DP_TX_AUX_REPLY_CNT 0x13c
+#define ZYNQMP_DP_TX_AUX_REPLY_CNT_MASK 0xff
+#define ZYNQMP_DP_TX_INTR_STATUS 0x140
+#define ZYNQMP_DP_TX_INTR_MASK 0x144
+#define ZYNQMP_DP_TX_INTR_HPD_IRQ BIT(0)
+#define ZYNQMP_DP_TX_INTR_HPD_EVENT BIT(1)
+#define ZYNQMP_DP_TX_INTR_REPLY_RECV BIT(2)
+#define ZYNQMP_DP_TX_INTR_REPLY_TIMEOUT BIT(3)
+#define ZYNQMP_DP_TX_INTR_HPD_PULSE BIT(4)
+#define ZYNQMP_DP_TX_INTR_EXT_PKT_TXD BIT(5)
+#define ZYNQMP_DP_TX_INTR_LIV_ABUF_UNDRFLW BIT(12)
+#define ZYNQMP_DP_TX_INTR_VBLANK_START BIT(13)
+#define ZYNQMP_DP_TX_INTR_PIXEL0_MATCH BIT(14)
+#define ZYNQMP_DP_TX_INTR_PIXEL1_MATCH BIT(15)
+#define ZYNQMP_DP_TX_INTR_CHBUF_UNDERFLW_MASK 0x3f0000
+#define ZYNQMP_DP_TX_INTR_CHBUF_OVERFLW_MASK 0xfc00000
+#define ZYNQMP_DP_TX_INTR_CUST_TS_2 BIT(28)
+#define ZYNQMP_DP_TX_INTR_CUST_TS BIT(29)
+#define ZYNQMP_DP_TX_INTR_EXT_VSYNC_TS BIT(30)
+#define ZYNQMP_DP_TX_INTR_VSYNC_TS BIT(31)
+#define ZYNQMP_DP_TX_INTR_ALL (ZYNQMP_DP_TX_INTR_HPD_IRQ | \
+ ZYNQMP_DP_TX_INTR_HPD_EVENT | \
+ ZYNQMP_DP_TX_INTR_REPLY_RECV | \
+ ZYNQMP_DP_TX_INTR_REPLY_TIMEOUT | \
+ ZYNQMP_DP_TX_INTR_HPD_PULSE | \
+ ZYNQMP_DP_TX_INTR_EXT_PKT_TXD | \
+ ZYNQMP_DP_TX_INTR_LIV_ABUF_UNDRFLW | \
+ ZYNQMP_DP_TX_INTR_CHBUF_UNDERFLW_MASK | \
+ ZYNQMP_DP_TX_INTR_CHBUF_OVERFLW_MASK)
+#define ZYNQMP_DP_TX_NO_INTR_ALL (ZYNQMP_DP_TX_INTR_PIXEL0_MATCH | \
+ ZYNQMP_DP_TX_INTR_PIXEL1_MATCH | \
+ ZYNQMP_DP_TX_INTR_CUST_TS_2 | \
+ ZYNQMP_DP_TX_INTR_CUST_TS | \
+ ZYNQMP_DP_TX_INTR_EXT_VSYNC_TS | \
+ ZYNQMP_DP_TX_INTR_VSYNC_TS)
+#define ZYNQMP_DP_TX_REPLY_DATA_CNT 0x148
+#define ZYNQMP_DP_SUB_TX_INTR_STATUS 0x3a0
+#define ZYNQMP_DP_SUB_TX_INTR_MASK 0x3a4
+#define ZYNQMP_DP_SUB_TX_INTR_EN 0x3a8
+#define ZYNQMP_DP_SUB_TX_INTR_DS 0x3ac
+
+/* Main stream attribute registers */
+#define ZYNQMP_DP_TX_MAIN_STREAM_HTOTAL 0x180
+#define ZYNQMP_DP_TX_MAIN_STREAM_VTOTAL 0x184
+#define ZYNQMP_DP_TX_MAIN_STREAM_POLARITY 0x188
+#define ZYNQMP_DP_TX_MAIN_STREAM_POLARITY_HSYNC_SHIFT 0
+#define ZYNQMP_DP_TX_MAIN_STREAM_POLARITY_VSYNC_SHIFT 1
+#define ZYNQMP_DP_TX_MAIN_STREAM_HSWIDTH 0x18c
+#define ZYNQMP_DP_TX_MAIN_STREAM_VSWIDTH 0x190
+#define ZYNQMP_DP_TX_MAIN_STREAM_HRES 0x194
+#define ZYNQMP_DP_TX_MAIN_STREAM_VRES 0x198
+#define ZYNQMP_DP_TX_MAIN_STREAM_HSTART 0x19c
+#define ZYNQMP_DP_TX_MAIN_STREAM_VSTART 0x1a0
+#define ZYNQMP_DP_TX_MAIN_STREAM_MISC0 0x1a4
+#define ZYNQMP_DP_TX_MAIN_STREAM_MISC0_SYNC BIT(0)
+#define ZYNQMP_DP_TX_MAIN_STREAM_MISC0_FORMAT_SHIFT 1
+#define ZYNQMP_DP_TX_MAIN_STREAM_MISC0_DYNAMIC_RANGE BIT(3)
+#define ZYNQMP_DP_TX_MAIN_STREAM_MISC0_YCBCR_COLRIMETRY BIT(4)
+#define ZYNQMP_DP_TX_MAIN_STREAM_MISC0_BPC_SHIFT 5
+#define ZYNQMP_DP_TX_MAIN_STREAM_MISC1 0x1a8
+#define ZYNQMP_DP_TX_MAIN_STREAM_MISC0_INTERLACED_VERT BIT(0)
+#define ZYNQMP_DP_TX_MAIN_STREAM_MISC0_STEREO_VID_SHIFT 1
+#define ZYNQMP_DP_TX_M_VID 0x1ac
+#define ZYNQMP_DP_TX_TRANSFER_UNIT_SIZE 0x1b0
+#define ZYNQMP_DP_TX_DEF_TRANSFER_UNIT_SIZE 64
+#define ZYNQMP_DP_TX_N_VID 0x1b4
+#define ZYNQMP_DP_TX_USER_PIXEL_WIDTH 0x1b8
+#define ZYNQMP_DP_TX_USER_DATA_CNT_PER_LANE 0x1bc
+#define ZYNQMP_DP_TX_MIN_BYTES_PER_TU 0x1c4
+#define ZYNQMP_DP_TX_FRAC_BYTES_PER_TU 0x1c8
+#define ZYNQMP_DP_TX_INIT_WAIT 0x1cc
+
+/* PHY configuration and status registers */
+#define ZYNQMP_DP_TX_PHY_CONFIG 0x200
+#define ZYNQMP_DP_TX_PHY_CONFIG_PHY_RESET BIT(0)
+#define ZYNQMP_DP_TX_PHY_CONFIG_GTTX_RESET BIT(1)
+#define ZYNQMP_DP_TX_PHY_CONFIG_PHY_PMA_RESET BIT(8)
+#define ZYNQMP_DP_TX_PHY_CONFIG_PHY_PCS_RESET BIT(9)
+#define ZYNQMP_DP_TX_PHY_CONFIG_ALL_RESET (ZYNQMP_DP_TX_PHY_CONFIG_PHY_RESET | \
+ ZYNQMP_DP_TX_PHY_CONFIG_GTTX_RESET | \
+ ZYNQMP_DP_TX_PHY_CONFIG_PHY_PMA_RESET | \
+ ZYNQMP_DP_TX_PHY_CONFIG_PHY_PCS_RESET)
+#define ZYNQMP_DP_TX_PHY_PREEMPHASIS_LANE_0 0x210
+#define ZYNQMP_DP_TX_PHY_PREEMPHASIS_LANE_1 0x214
+#define ZYNQMP_DP_TX_PHY_PREEMPHASIS_LANE_2 0x218
+#define ZYNQMP_DP_TX_PHY_PREEMPHASIS_LANE_3 0x21c
+#define ZYNQMP_DP_TX_PHY_VOLTAGE_DIFF_LANE_0 0x220
+#define ZYNQMP_DP_TX_PHY_VOLTAGE_DIFF_LANE_1 0x224
+#define ZYNQMP_DP_TX_PHY_VOLTAGE_DIFF_LANE_2 0x228
+#define ZYNQMP_DP_TX_PHY_VOLTAGE_DIFF_LANE_3 0x22c
+#define ZYNQMP_DP_TX_PHY_CLOCK_FEEDBACK_SETTING 0x234
+#define ZYNQMP_DP_TX_PHY_CLOCK_FEEDBACK_SETTING_162 0x1
+#define ZYNQMP_DP_TX_PHY_CLOCK_FEEDBACK_SETTING_270 0x3
+#define ZYNQMP_DP_TX_PHY_CLOCK_FEEDBACK_SETTING_540 0x5
+#define ZYNQMP_DP_TX_PHY_POWER_DOWN 0x238
+#define ZYNQMP_DP_TX_PHY_POWER_DOWN_LANE_0 BIT(0)
+#define ZYNQMP_DP_TX_PHY_POWER_DOWN_LANE_1 BIT(1)
+#define ZYNQMP_DP_TX_PHY_POWER_DOWN_LANE_2 BIT(2)
+#define ZYNQMP_DP_TX_PHY_POWER_DOWN_LANE_3 BIT(3)
+#define ZYNQMP_DP_TX_PHY_POWER_DOWN_ALL 0xf
+#define ZYNQMP_DP_TX_PHY_PRECURSOR_LANE_0 0x23c
+#define ZYNQMP_DP_TX_PHY_PRECURSOR_LANE_1 0x240
+#define ZYNQMP_DP_TX_PHY_PRECURSOR_LANE_2 0x244
+#define ZYNQMP_DP_TX_PHY_PRECURSOR_LANE_3 0x248
+#define ZYNQMP_DP_TX_PHY_POSTCURSOR_LANE_0 0x24c
+#define ZYNQMP_DP_TX_PHY_POSTCURSOR_LANE_1 0x250
+#define ZYNQMP_DP_TX_PHY_POSTCURSOR_LANE_2 0x254
+#define ZYNQMP_DP_TX_PHY_POSTCURSOR_LANE_3 0x258
+#define ZYNQMP_DP_SUB_TX_PHY_PRECURSOR_LANE_0 0x24c
+#define ZYNQMP_DP_SUB_TX_PHY_PRECURSOR_LANE_1 0x250
+#define ZYNQMP_DP_TX_PHY_STATUS 0x280
+#define ZYNQMP_DP_TX_PHY_STATUS_PLL_LOCKED_SHIFT 4
+#define ZYNQMP_DP_TX_PHY_STATUS_FPGA_PLL_LOCKED BIT(6)
+
+/* Audio registers */
+#define ZYNQMP_DP_TX_AUDIO_CONTROL 0x300
+#define ZYNQMP_DP_TX_AUDIO_CHANNELS 0x304
+#define ZYNQMP_DP_TX_AUDIO_INFO_DATA 0x308
+#define ZYNQMP_DP_TX_AUDIO_M_AUD 0x328
+#define ZYNQMP_DP_TX_AUDIO_N_AUD 0x32c
+#define ZYNQMP_DP_TX_AUDIO_EXT_DATA 0x330
+
+#define ZYNQMP_DP_MISC0_RGB (0)
+#define ZYNQMP_DP_MISC0_YCRCB_422 (5 << 1)
+#define ZYNQMP_DP_MISC0_YCRCB_444 (6 << 1)
+#define ZYNQMP_DP_MISC0_FORMAT_MASK 0xe
+#define ZYNQMP_DP_MISC0_BPC_6 (0 << 5)
+#define ZYNQMP_DP_MISC0_BPC_8 (1 << 5)
+#define ZYNQMP_DP_MISC0_BPC_10 (2 << 5)
+#define ZYNQMP_DP_MISC0_BPC_12 (3 << 5)
+#define ZYNQMP_DP_MISC0_BPC_16 (4 << 5)
+#define ZYNQMP_DP_MISC0_BPC_MASK 0xe0
+#define ZYNQMP_DP_MISC1_Y_ONLY (1 << 7)
+
+#define ZYNQMP_DP_MAX_LANES 2
+#define ZYNQMP_MAX_FREQ 3000000
+
+#define DP_REDUCED_BIT_RATE 162000
+#define DP_HIGH_BIT_RATE 270000
+#define DP_HIGH_BIT_RATE2 540000
+#define DP_MAX_TRAINING_TRIES 5
+#define DP_V1_2 0x12
+
+/**
+ * struct zynqmp_dp_link_config - Common link config between source and sink
+ * @max_rate: maximum link rate
+ * @max_lanes: maximum number of lanes
+ */
+struct zynqmp_dp_link_config {
+ int max_rate;
+ u8 max_lanes;
+};
+
+/**
+ * struct zynqmp_dp_mode - Configured mode of DisplayPort
+ * @bw_code: code for bandwidth(link rate)
+ * @lane_cnt: number of lanes
+ * @pclock: pixel clock frequency of current mode
+ * @fmt: format identifier string
+ */
+struct zynqmp_dp_mode {
+ u8 bw_code;
+ u8 lane_cnt;
+ int pclock;
+ const char *fmt;
+};
+
+/**
+ * struct zynqmp_dp_config - Configuration of DisplayPort from DTS
+ * @misc0: misc0 configuration (per DP v1.2 spec)
+ * @misc1: misc1 configuration (per DP v1.2 spec)
+ * @bpp: bits per pixel
+ * @bpc: bits per component
+ * @num_colors: number of color components
+ */
+struct zynqmp_dp_config {
+ u8 misc0;
+ u8 misc1;
+ u8 bpp;
+ u8 bpc;
+ u8 num_colors;
+};
+
+/**
+ * struct zynqmp_dp - Xilinx DisplayPort core
+ * @encoder: the drm encoder structure
+ * @connector: the drm connector structure
+ * @dev: device structure
+ * @dpsub: Display subsystem
+ * @drm: DRM core
+ * @iomem: device I/O memory for register access
+ * @irq: irq
+ * @config: IP core configuration from DTS
+ * @aux: aux channel
+ * @phy: PHY handles for DP lanes
+ * @num_lanes: number of enabled phy lanes
+ * @hpd_work: hot plug detection worker
+ * @status: connection status
+ * @enabled: flag to indicate if the device is enabled
+ * @dpms: current dpms state
+ * @dpcd: DP configuration data from currently connected sink device
+ * @link_config: common link configuration between IP core and sink device
+ * @mode: current mode between IP core and sink device
+ * @train_set: set of training data
+ */
+struct zynqmp_dp {
+ struct drm_encoder encoder;
+ struct drm_connector connector;
+ struct device *dev;
+ struct zynqmp_dpsub *dpsub;
+ struct drm_device *drm;
+ void __iomem *iomem;
+ int irq;
+
+ struct zynqmp_dp_config config;
+ struct drm_dp_aux aux;
+ struct phy *phy[ZYNQMP_DP_MAX_LANES];
+ u8 num_lanes;
+ struct delayed_work hpd_work;
+ enum drm_connector_status status;
+ bool enabled;
+
+ int dpms;
+ u8 dpcd[DP_RECEIVER_CAP_SIZE];
+ struct zynqmp_dp_link_config link_config;
+ struct zynqmp_dp_mode mode;
+ u8 train_set[ZYNQMP_DP_MAX_LANES];
+};
+
+static inline struct zynqmp_dp *encoder_to_dp(struct drm_encoder *encoder)
+{
+ return container_of(encoder, struct zynqmp_dp, encoder);
+}
+
+static inline struct zynqmp_dp *connector_to_dp(struct drm_connector *connector)
+{
+ return container_of(connector, struct zynqmp_dp, connector);
+}
+
+static void zynqmp_dp_write(void __iomem *base, int offset, u32 val)
+{
+ writel(val, base + offset);
+}
+
+static u32 zynqmp_dp_read(void __iomem *base, int offset)
+{
+ return readl(base + offset);
+}
+
+static void zynqmp_dp_clr(void __iomem *base, int offset, u32 clr)
+{
+ zynqmp_dp_write(base, offset, zynqmp_dp_read(base, offset) & ~clr);
+}
+
+static void zynqmp_dp_set(void __iomem *base, int offset, u32 set)
+{
+ zynqmp_dp_write(base, offset, zynqmp_dp_read(base, offset) | set);
+}
+
+/*
+ * Internal functions: used by zynqmp_disp.c
+ */
+
+/**
+ * zynqmp_dp_update_bpp - Update the current bpp config
+ * @dp: DisplayPort IP core structure
+ *
+ * Update the current bpp based on the color format: bpc & num_colors.
+ * Any function that changes bpc or num_colors should call this
+ * to keep the bpp value in sync.
+ */
+static void zynqmp_dp_update_bpp(struct zynqmp_dp *dp)
+{
+ struct zynqmp_dp_config *config = &dp->config;
+
+ config->bpp = dp->config.bpc * dp->config.num_colors;
+}
+
+/**
+ * zynqmp_dp_set_color - Set the color
+ * @dp: DisplayPort IP core structure
+ * @color: color string, from zynqmp_disp_color_enum
+ *
+ * Update misc register values based on @color string.
+ *
+ * Return: 0 on success, or -EINVAL.
+ */
+int zynqmp_dp_set_color(struct zynqmp_dp *dp, const char *color)
+{
+ struct zynqmp_dp_config *config = &dp->config;
+
+ config->misc0 &= ~ZYNQMP_DP_MISC0_FORMAT_MASK;
+ config->misc1 &= ~ZYNQMP_DP_MISC1_Y_ONLY;
+ if (strcmp(color, "rgb") == 0) {
+ config->misc0 |= ZYNQMP_DP_MISC0_RGB;
+ config->num_colors = 3;
+ } else if (strcmp(color, "ycrcb422") == 0) {
+ config->misc0 |= ZYNQMP_DP_MISC0_YCRCB_422;
+ config->num_colors = 2;
+ } else if (strcmp(color, "ycrcb444") == 0) {
+ config->misc0 |= ZYNQMP_DP_MISC0_YCRCB_444;
+ config->num_colors = 3;
+ } else if (strcmp(color, "yonly") == 0) {
+ config->misc1 |= ZYNQMP_DP_MISC1_Y_ONLY;
+ config->num_colors = 1;
+ } else {
+ dev_err(dp->dev, "Invalid colormetry in DT\n");
+ return -EINVAL;
+ }
+ zynqmp_dp_update_bpp(dp);
+
+ return 0;
+}
+
+/**
+ * zynqmp_dp_enable_vblank - Enable vblank
+ * @dp: DisplayPort IP core structure
+ *
+ * Enable vblank interrupt
+ */
+void zynqmp_dp_enable_vblank(struct zynqmp_dp *dp)
+{
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_SUB_TX_INTR_EN,
+ ZYNQMP_DP_TX_INTR_VBLANK_START);
+}
+
+/**
+ * zynqmp_dp_disable_vblank - Disable vblank
+ * @dp: DisplayPort IP core structure
+ *
+ * Disable vblank interrupt
+ */
+void zynqmp_dp_disable_vblank(struct zynqmp_dp *dp)
+{
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_SUB_TX_INTR_DS,
+ ZYNQMP_DP_TX_INTR_VBLANK_START);
+}
+
+/*
+ * DP PHY functions
+ */
+
+/**
+ * zynqmp_dp_init_phy - Initialize the phy
+ * @dp: DisplayPort IP core structure
+ *
+ * Initialize the phy.
+ *
+ * Return: 0 if the phy instances are initialized correctly, or the error code
+ * returned from the callee functions.
+ */
+static int zynqmp_dp_init_phy(struct zynqmp_dp *dp)
+{
+ unsigned int i;
+ int ret;
+
+ for (i = 0; i < ZYNQMP_DP_MAX_LANES; i++) {
+ ret = phy_init(dp->phy[i]);
+ if (ret) {
+ dev_err(dp->dev, "failed to init phy lane %d\n", i);
+ return ret;
+ }
+ }
+
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_SUB_TX_INTR_DS,
+ ZYNQMP_DP_TX_INTR_ALL);
+ zynqmp_dp_clr(dp->iomem, ZYNQMP_DP_TX_PHY_CONFIG,
+ ZYNQMP_DP_TX_PHY_CONFIG_ALL_RESET);
+
+ return 0;
+}
+
+/**
+ * zynqmp_dp_exit_phy - Exit the phy
+ * @dp: DisplayPort IP core structure
+ *
+ * Exit the phy.
+ */
+static void zynqmp_dp_exit_phy(struct zynqmp_dp *dp)
+{
+ unsigned int i;
+ int ret;
+
+ for (i = 0; i < ZYNQMP_DP_MAX_LANES; i++) {
+ ret = phy_exit(dp->phy[i]);
+ if (ret)
+ dev_err(dp->dev, "failed to exit phy(%d) %d\n", i, ret);
+ }
+}
+
+/**
+ * zynqmp_dp_phy_ready - Check if PHY is ready
+ * @dp: DisplayPort IP core structure
+ *
+ * Check if PHY is ready. If PHY is not ready, wait 1ms to check for 100 times.
+ * This amount of delay was suggested by IP designer.
+ *
+ * Return: 0 if PHY is ready, or -ENODEV if PHY is not ready.
+ */
+static int zynqmp_dp_phy_ready(struct zynqmp_dp *dp)
+{
+ u32 i, reg, ready;
+
+ ready = (1 << ZYNQMP_DP_MAX_LANES) - 1;
+
+ /* Wait for 100 * 1ms. This should be enough time for PHY to be ready */
+ for (i = 0; ; i++) {
+ reg = zynqmp_dp_read(dp->iomem, ZYNQMP_DP_TX_PHY_STATUS);
+ if ((reg & ready) == ready)
+ return 0;
+
+ if (i == 100) {
+ dev_err(dp->dev, "PHY isn't ready\n");
+ return -ENODEV;
+ }
+
+ usleep_range(1000, 1100);
+ }
+
+ return 0;
+}
+
+/*
+ * DP functions
+ */
+
+/**
+ * zynqmp_dp_max_rate - Calculate and return available max pixel clock
+ * @link_rate: link rate (Kilo-bytes / sec)
+ * @lane_num: number of lanes
+ * @bpp: bits per pixel
+ *
+ * Return: max pixel clock (KHz) supported by current link config.
+ */
+static inline int zynqmp_dp_max_rate(int link_rate, u8 lane_num, u8 bpp)
+{
+ return link_rate * lane_num * 8 / bpp;
+}
+
+/**
+ * zynqmp_dp_mode_configure - Configure the link values
+ * @dp: DisplayPort IP core structure
+ * @pclock: pixel clock for requested display mode
+ * @current_bw: current link rate
+ *
+ * Find the link configuration values, rate and lane count for requested pixel
+ * clock @pclock. The @pclock is stored in the mode to be used in other
+ * functions later. The returned rate is downshifted from the current rate
+ * @current_bw.
+ *
+ * Return: Current link rate code, or -EINVAL.
+ */
+static int zynqmp_dp_mode_configure(struct zynqmp_dp *dp, int pclock,
+ u8 current_bw)
+{
+ int max_rate = dp->link_config.max_rate;
+ u8 bws[3] = { DP_LINK_BW_1_62, DP_LINK_BW_2_7, DP_LINK_BW_5_4 };
+ u8 max_lanes = dp->link_config.max_lanes;
+ u8 max_link_rate_code = drm_dp_link_rate_to_bw_code(max_rate);
+ u8 bpp = dp->config.bpp;
+ u8 lane_cnt;
+ s8 i;
+
+ if (current_bw == DP_LINK_BW_1_62) {
+ dev_err(dp->dev, "can't downshift. already lowest link rate\n");
+ return -EINVAL;
+ }
+
+ for (i = ARRAY_SIZE(bws) - 1; i >= 0; i--) {
+ if (current_bw && bws[i] >= current_bw)
+ continue;
+
+ if (bws[i] <= max_link_rate_code)
+ break;
+ }
+
+ for (lane_cnt = 1; lane_cnt <= max_lanes; lane_cnt <<= 1) {
+ int bw;
+ u32 rate;
+
+ bw = drm_dp_bw_code_to_link_rate(bws[i]);
+ rate = zynqmp_dp_max_rate(bw, lane_cnt, bpp);
+ if (pclock <= rate) {
+ dp->mode.bw_code = bws[i];
+ dp->mode.lane_cnt = lane_cnt;
+ dp->mode.pclock = pclock;
+ return dp->mode.bw_code;
+ }
+ }
+
+ dev_err(dp->dev, "failed to configure link values\n");
+
+ return -EINVAL;
+}
+
+/**
+ * zynqmp_dp_adjust_train - Adjust train values
+ * @dp: DisplayPort IP core structure
+ * @link_status: link status from sink which contains requested training values
+ */
+static void zynqmp_dp_adjust_train(struct zynqmp_dp *dp,
+ u8 link_status[DP_LINK_STATUS_SIZE])
+{
+ u8 *train_set = dp->train_set;
+ u8 voltage = 0, preemphasis = 0;
+ u8 i;
+
+ for (i = 0; i < dp->mode.lane_cnt; i++) {
+ u8 v = drm_dp_get_adjust_request_voltage(link_status, i);
+ u8 p = drm_dp_get_adjust_request_pre_emphasis(link_status, i);
+
+ if (v > voltage)
+ voltage = v;
+
+ if (p > preemphasis)
+ preemphasis = p;
+ }
+
+ if (voltage >= DP_TRAIN_VOLTAGE_SWING_LEVEL_3)
+ voltage |= DP_TRAIN_MAX_SWING_REACHED;
+
+ if (preemphasis >= DP_TRAIN_PRE_EMPH_LEVEL_2)
+ preemphasis |= DP_TRAIN_MAX_PRE_EMPHASIS_REACHED;
+
+ for (i = 0; i < dp->mode.lane_cnt; i++)
+ train_set[i] = voltage | preemphasis;
+}
+
+/**
+ * zynqmp_dp_update_vs_emph - Update the training values
+ * @dp: DisplayPort IP core structure
+ *
+ * Update the training values based on the request from sink. The mapped values
+ * are predefined, and values(vs, pe, pc) are from the device manual.
+ *
+ * Return: 0 if vs and emph are updated successfully, or the error code returned
+ * by drm_dp_dpcd_write().
+ */
+static int zynqmp_dp_update_vs_emph(struct zynqmp_dp *dp)
+{
+ u8 *train_set = dp->train_set;
+ u8 i, v_level, p_level;
+ int ret;
+
+ ret = drm_dp_dpcd_write(&dp->aux, DP_TRAINING_LANE0_SET, train_set,
+ dp->mode.lane_cnt);
+ if (ret < 0)
+ return ret;
+
+ for (i = 0; i < dp->mode.lane_cnt; i++) {
+ u32 reg = ZYNQMP_DP_SUB_TX_PHY_PRECURSOR_LANE_0 + i * 4;
+
+ v_level = (train_set[i] & DP_TRAIN_VOLTAGE_SWING_MASK) >>
+ DP_TRAIN_VOLTAGE_SWING_SHIFT;
+ p_level = (train_set[i] & DP_TRAIN_PRE_EMPHASIS_MASK) >>
+ DP_TRAIN_PRE_EMPHASIS_SHIFT;
+
+ zynqmp_dp_write(dp->iomem, reg, 0x2);
+ }
+
+ return 0;
+}
+
+/**
+ * zynqmp_dp_link_train_cr - Train clock recovery
+ * @dp: DisplayPort IP core structure
+ *
+ * Return: 0 if clock recovery train is done successfully, or corresponding
+ * error code.
+ */
+static int zynqmp_dp_link_train_cr(struct zynqmp_dp *dp)
+{
+ u8 link_status[DP_LINK_STATUS_SIZE];
+ u8 lane_cnt = dp->mode.lane_cnt;
+ u8 vs = 0, tries = 0;
+ u16 max_tries, i;
+ bool cr_done;
+ int ret;
+
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_TRAINING_PATTERN_SET,
+ DP_TRAINING_PATTERN_1);
+ ret = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET,
+ DP_TRAINING_PATTERN_1 |
+ DP_LINK_SCRAMBLING_DISABLE);
+ if (ret < 0)
+ return ret;
+
+ /*
+ * 256 loops should be maximum iterations for 4 lanes and 4 values.
+ * So, This loop should exit before 512 iterations
+ */
+ for (max_tries = 0; max_tries < 512; max_tries++) {
+ ret = zynqmp_dp_update_vs_emph(dp);
+ if (ret)
+ return ret;
+
+ drm_dp_link_train_clock_recovery_delay(dp->dpcd);
+ ret = drm_dp_dpcd_read_link_status(&dp->aux, link_status);
+ if (ret < 0)
+ return ret;
+
+ cr_done = drm_dp_clock_recovery_ok(link_status, lane_cnt);
+ if (cr_done)
+ break;
+
+ for (i = 0; i < lane_cnt; i++)
+ if (!(dp->train_set[i] & DP_TRAIN_MAX_SWING_REACHED))
+ break;
+ if (i == lane_cnt)
+ break;
+
+ if ((dp->train_set[0] & DP_TRAIN_VOLTAGE_SWING_MASK) == vs)
+ tries++;
+ else
+ tries = 0;
+
+ if (tries == DP_MAX_TRAINING_TRIES)
+ break;
+
+ vs = dp->train_set[0] & DP_TRAIN_VOLTAGE_SWING_MASK;
+ zynqmp_dp_adjust_train(dp, link_status);
+ }
+
+ if (!cr_done)
+ return -EIO;
+
+ return 0;
+}
+
+/**
+ * zynqmp_dp_link_train_ce - Train channel equalization
+ * @dp: DisplayPort IP core structure
+ *
+ * Return: 0 if channel equalization train is done successfully, or
+ * corresponding error code.
+ */
+static int zynqmp_dp_link_train_ce(struct zynqmp_dp *dp)
+{
+ u8 link_status[DP_LINK_STATUS_SIZE];
+ u8 lane_cnt = dp->mode.lane_cnt;
+ u32 pat, tries;
+ int ret;
+ bool ce_done;
+
+ if (dp->dpcd[DP_DPCD_REV] >= DP_V1_2 &&
+ dp->dpcd[DP_MAX_LANE_COUNT] & DP_TPS3_SUPPORTED)
+ pat = DP_TRAINING_PATTERN_3;
+ else
+ pat = DP_TRAINING_PATTERN_2;
+
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_TRAINING_PATTERN_SET, pat);
+ ret = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET,
+ pat | DP_LINK_SCRAMBLING_DISABLE);
+ if (ret < 0)
+ return ret;
+
+ for (tries = 0; tries < DP_MAX_TRAINING_TRIES; tries++) {
+ ret = zynqmp_dp_update_vs_emph(dp);
+ if (ret)
+ return ret;
+
+ drm_dp_link_train_channel_eq_delay(dp->dpcd);
+ ret = drm_dp_dpcd_read_link_status(&dp->aux, link_status);
+ if (ret < 0)
+ return ret;
+
+ ce_done = drm_dp_channel_eq_ok(link_status, lane_cnt);
+ if (ce_done)
+ break;
+
+ zynqmp_dp_adjust_train(dp, link_status);
+ }
+
+ if (!ce_done)
+ return -EIO;
+
+ return 0;
+}
+
+/**
+ * zynqmp_dp_link_train - Train the link
+ * @dp: DisplayPort IP core structure
+ *
+ * Return: 0 if all trains are done successfully, or corresponding error code.
+ */
+static int zynqmp_dp_train(struct zynqmp_dp *dp)
+{
+ u32 reg;
+ u8 bw_code = dp->mode.bw_code;
+ u8 lane_cnt = dp->mode.lane_cnt;
+ u8 aux_lane_cnt = lane_cnt;
+ bool enhanced;
+ int ret;
+
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_LANE_CNT_SET, lane_cnt);
+ enhanced = drm_dp_enhanced_frame_cap(dp->dpcd);
+ if (enhanced) {
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_ENHANCED_FRAME_EN, 1);
+ aux_lane_cnt |= DP_LANE_COUNT_ENHANCED_FRAME_EN;
+ }
+
+ if (dp->dpcd[3] & 0x1) {
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_DOWNSPREAD_CTL, 1);
+ drm_dp_dpcd_writeb(&dp->aux, DP_DOWNSPREAD_CTRL,
+ DP_SPREAD_AMP_0_5);
+ } else {
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_DOWNSPREAD_CTL, 0);
+ drm_dp_dpcd_writeb(&dp->aux, DP_DOWNSPREAD_CTRL, 0);
+ }
+
+ ret = drm_dp_dpcd_writeb(&dp->aux, DP_LANE_COUNT_SET, aux_lane_cnt);
+ if (ret < 0) {
+ dev_err(dp->dev, "failed to set lane count\n");
+ return ret;
+ }
+
+ ret = drm_dp_dpcd_writeb(&dp->aux, DP_MAIN_LINK_CHANNEL_CODING_SET,
+ DP_SET_ANSI_8B10B);
+ if (ret < 0) {
+ dev_err(dp->dev, "failed to set ANSI 8B/10B encoding\n");
+ return ret;
+ }
+
+ ret = drm_dp_dpcd_writeb(&dp->aux, DP_LINK_BW_SET, bw_code);
+ if (ret < 0) {
+ dev_err(dp->dev, "failed to set DP bandwidth\n");
+ return ret;
+ }
+
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_LINK_BW_SET, bw_code);
+ switch (bw_code) {
+ case DP_LINK_BW_1_62:
+ reg = ZYNQMP_DP_TX_PHY_CLOCK_FEEDBACK_SETTING_162;
+ break;
+ case DP_LINK_BW_2_7:
+ reg = ZYNQMP_DP_TX_PHY_CLOCK_FEEDBACK_SETTING_270;
+ break;
+ case DP_LINK_BW_5_4:
+ default:
+ reg = ZYNQMP_DP_TX_PHY_CLOCK_FEEDBACK_SETTING_540;
+ break;
+ }
+
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_PHY_CLOCK_FEEDBACK_SETTING,
+ reg);
+ ret = zynqmp_dp_phy_ready(dp);
+ if (ret < 0)
+ return ret;
+
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_SCRAMBLING_DISABLE, 1);
+ memset(dp->train_set, 0, 4);
+ ret = zynqmp_dp_link_train_cr(dp);
+ if (ret)
+ return ret;
+
+ ret = zynqmp_dp_link_train_ce(dp);
+ if (ret)
+ return ret;
+
+ ret = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET,
+ DP_TRAINING_PATTERN_DISABLE);
+ if (ret < 0) {
+ dev_err(dp->dev, "failed to disable training pattern\n");
+ return ret;
+ }
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_TRAINING_PATTERN_SET,
+ DP_TRAINING_PATTERN_DISABLE);
+
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_SCRAMBLING_DISABLE, 0);
+
+ return 0;
+}
+
+/**
+ * zynqmp_dp_train_loop - Downshift the link rate during training
+ * @dp: DisplayPort IP core structure
+ *
+ * Train the link by downshifting the link rate if training is not successful.
+ */
+static void zynqmp_dp_train_loop(struct zynqmp_dp *dp)
+{
+ struct zynqmp_dp_mode *mode = &dp->mode;
+ u8 bw = mode->bw_code;
+ int ret;
+
+ do {
+ if (dp->status == connector_status_disconnected ||
+ !dp->enabled)
+ return;
+
+ ret = zynqmp_dp_train(dp);
+ if (!ret)
+ return;
+
+ ret = zynqmp_dp_mode_configure(dp, mode->pclock, bw);
+ if (ret < 0)
+ goto err_out;
+
+ bw = ret;
+ } while (bw >= DP_LINK_BW_1_62);
+
+err_out:
+ dev_err(dp->dev, "failed to train the DP link\n");
+}
+
+/*
+ * DP Aux functions
+ */
+
+#define AUX_READ_BIT 0x1
+
+/**
+ * zynqmp_dp_aux_cmd_submit - Submit aux command
+ * @dp: DisplayPort IP core structure
+ * @cmd: aux command
+ * @addr: aux address
+ * @buf: buffer for command data
+ * @bytes: number of bytes for @buf
+ * @reply: reply code to be returned
+ *
+ * Submit an aux command. All aux related commands, native or i2c aux
+ * read/write, are submitted through this function. The function is mapped to
+ * the transfer function of struct drm_dp_aux. This function involves in
+ * multiple register reads/writes, thus synchronization is needed, and it is
+ * done by drm_dp_helper using @hw_mutex. The calling thread goes into sleep
+ * if there's no immediate reply to the command submission. The reply code is
+ * returned at @reply if @reply != NULL.
+ *
+ * Return: 0 if the command is submitted properly, or corresponding error code:
+ * -EBUSY when there is any request already being processed
+ * -ETIMEDOUT when receiving reply is timed out
+ * -EIO when received bytes are less than requested
+ */
+static int zynqmp_dp_aux_cmd_submit(struct zynqmp_dp *dp, u32 cmd, u16 addr,
+ u8 *buf, u8 bytes, u8 *reply)
+{
+ bool is_read = (cmd & AUX_READ_BIT) ? true : false;
+ void __iomem *iomem = dp->iomem;
+ u32 reg, i;
+
+ reg = zynqmp_dp_read(iomem, ZYNQMP_DP_TX_INTR_SIGNAL_STATE);
+ if (reg & ZYNQMP_DP_TX_INTR_SIGNAL_STATE_REQUEST)
+ return -EBUSY;
+
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_AUX_ADDRESS, addr);
+ if (!is_read)
+ for (i = 0; i < bytes; i++)
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_AUX_WRITE_FIFO,
+ buf[i]);
+
+ reg = cmd << ZYNQMP_DP_TX_AUX_COMMAND_CMD_SHIFT;
+ if (!buf || !bytes)
+ reg |= ZYNQMP_DP_TX_AUX_COMMAND_ADDRESS_ONLY;
+ else
+ reg |= (bytes - 1) << ZYNQMP_DP_TX_AUX_COMMAND_BYTES_SHIFT;
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_AUX_COMMAND, reg);
+
+ /* Wait for reply to be delivered upto 2ms */
+ for (i = 0; ; i++) {
+ reg = zynqmp_dp_read(iomem, ZYNQMP_DP_TX_INTR_SIGNAL_STATE);
+ if (reg & ZYNQMP_DP_TX_INTR_SIGNAL_STATE_REPLY)
+ break;
+
+ if (reg & ZYNQMP_DP_TX_INTR_SIGNAL_STATE_REPLY_TIMEOUT ||
+ i == 2)
+ return -ETIMEDOUT;
+
+ usleep_range(1000, 1100);
+ }
+
+ reg = zynqmp_dp_read(iomem, ZYNQMP_DP_TX_AUX_REPLY_CODE);
+ if (reply)
+ *reply = reg;
+
+ if (is_read &&
+ (reg == ZYNQMP_DP_TX_AUX_REPLY_CODE_AUX_ACK ||
+ reg == ZYNQMP_DP_TX_AUX_REPLY_CODE_I2C_ACK)) {
+ reg = zynqmp_dp_read(iomem, ZYNQMP_DP_TX_REPLY_DATA_CNT);
+ if ((reg & ZYNQMP_DP_TX_AUX_REPLY_CNT_MASK) != bytes)
+ return -EIO;
+
+ for (i = 0; i < bytes; i++) {
+ buf[i] = zynqmp_dp_read(iomem,
+ ZYNQMP_DP_TX_AUX_REPLY_DATA);
+ }
+ }
+
+ return 0;
+}
+
+static ssize_t
+zynqmp_dp_aux_transfer(struct drm_dp_aux *aux, struct drm_dp_aux_msg *msg)
+{
+ struct zynqmp_dp *dp = container_of(aux, struct zynqmp_dp, aux);
+ int ret;
+ unsigned int i, iter;
+
+ /* Number of loops = timeout in msec / aux delay (400 usec) */
+ iter = zynqmp_dp_aux_timeout_ms * 1000 / 400;
+ iter = iter ? iter : 1;
+
+ for (i = 0; i < iter; i++) {
+ ret = zynqmp_dp_aux_cmd_submit(dp, msg->request, msg->address,
+ msg->buffer, msg->size,
+ &msg->reply);
+ if (!ret) {
+ dev_dbg(dp->dev, "aux %d retries\n", i);
+ return msg->size;
+ }
+
+ if (dp->status == connector_status_disconnected) {
+ dev_dbg(dp->dev, "no connected aux device\n");
+ return -ENODEV;
+ }
+
+ usleep_range(400, 500);
+ }
+
+ dev_dbg(dp->dev, "failed to do aux transfer (%d)\n", ret);
+
+ return ret;
+}
+
+/**
+ * zynqmp_dp_init_aux - Initialize the DP aux
+ * @dp: DisplayPort IP core structure
+ *
+ * Initialize the DP aux. The aux clock is derived from the axi clock, so
+ * this function gets the axi clock frequency and calculates the filter
+ * value. Additionally, the interrupts and transmitter are enabled.
+ *
+ * Return: 0 on success, error value otherwise
+ */
+static int zynqmp_dp_init_aux(struct zynqmp_dp *dp)
+{
+ unsigned int rate;
+ u32 reg, w;
+
+ rate = zynqmp_disp_get_apb_clk_rate(dp->dpsub->disp);
+ if (rate < ZYNQMP_DP_TX_CLK_DIVIDER_MHZ) {
+ dev_err(dp->dev, "aclk should be higher than 1MHz\n");
+ return -EINVAL;
+ }
+
+ /* Allowable values for this register are: 8, 16, 24, 32, 40, 48 */
+ for (w = 8; w <= 48; w += 8) {
+ /* AUX pulse width should be between 0.4 to 0.6 usec */
+ if (w >= (4 * rate / 10000000) &&
+ w <= (6 * rate / 10000000))
+ break;
+ }
+
+ if (w > 48) {
+ dev_err(dp->dev, "aclk frequency too high\n");
+ return -EINVAL;
+ }
+ reg = w << ZYNQMP_DP_TX_CLK_DIVIDER_AUX_FILTER_SHIFT;
+ reg |= rate / ZYNQMP_DP_TX_CLK_DIVIDER_MHZ;
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_CLK_DIVIDER, reg);
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_SUB_TX_INTR_EN,
+ ZYNQMP_DP_TX_INTR_ALL);
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_SUB_TX_INTR_DS,
+ ZYNQMP_DP_TX_NO_INTR_ALL);
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_ENABLE, 1);
+
+ return 0;
+}
+
+/**
+ * zynqmp_dp_exit_aux - De-initialize the DP aux
+ * @dp: DisplayPort IP core structure
+ *
+ * De-initialize the DP aux. Disable all interrupts which are enabled
+ * through aux initialization, as well as the transmitter.
+ */
+static void zynqmp_dp_exit_aux(struct zynqmp_dp *dp)
+{
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_ENABLE, 0);
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_SUB_TX_INTR_DS, 0xffffffff);
+}
+
+/*
+ * Generic DP functions
+ */
+
+/**
+ * zynqmp_dp_update_misc - Write the misc registers
+ * @dp: DisplayPort IP core structure
+ *
+ * The misc register values are stored in the structure, and this
+ * function applies the values into the registers.
+ */
+static void zynqmp_dp_update_misc(struct zynqmp_dp *dp)
+{
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_MAIN_STREAM_MISC0,
+ dp->config.misc0);
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_MAIN_STREAM_MISC1,
+ dp->config.misc1);
+}
+
+/**
+ * zynqmp_dp_set_bpc - Set bpc value in software misc state
+ * @dp: DisplayPort IP core structure
+ * @bpc: bits per component
+ *
+ * Return: 0 on success, or the fallback bpc value
+ */
+static u8 zynqmp_dp_set_bpc(struct zynqmp_dp *dp, u8 bpc)
+{
+ struct zynqmp_dp_config *config = &dp->config;
+ u8 ret = 0;
+
+ if (dp->connector.display_info.bpc &&
+ dp->connector.display_info.bpc != bpc) {
+ dev_err(dp->dev, "requested bpc (%u) != display info (%u)\n",
+ bpc, dp->connector.display_info.bpc);
+ bpc = dp->connector.display_info.bpc;
+ }
+
+ config->misc0 &= ~ZYNQMP_DP_MISC0_BPC_MASK;
+ switch (bpc) {
+ case 6:
+ config->misc0 |= ZYNQMP_DP_MISC0_BPC_6;
+ break;
+ case 8:
+ config->misc0 |= ZYNQMP_DP_MISC0_BPC_8;
+ break;
+ case 10:
+ config->misc0 |= ZYNQMP_DP_MISC0_BPC_10;
+ break;
+ case 12:
+ config->misc0 |= ZYNQMP_DP_MISC0_BPC_12;
+ break;
+ case 16:
+ config->misc0 |= ZYNQMP_DP_MISC0_BPC_16;
+ break;
+ default:
+ dev_err(dp->dev, "Not supported bpc (%u). fall back to 8bpc\n",
+ bpc);
+ config->misc0 |= ZYNQMP_DP_MISC0_BPC_8;
+ ret = 8;
+ break;
+ }
+ config->bpc = bpc;
+ zynqmp_dp_update_bpp(dp);
+
+ return ret;
+}
+
+/**
+ * zynqmp_dp_encoder_mode_set_transfer_unit - Set the transfer unit values
+ * @dp: DisplayPort IP core structure
+ * @mode: requested display mode
+ *
+ * Set the transfer unit, and caculate all transfer unit size related values.
+ * Calculation is based on DP and IP core specification.
+ */
+static void
+zynqmp_dp_encoder_mode_set_transfer_unit(struct zynqmp_dp *dp,
+ struct drm_display_mode *mode)
+{
+ u32 tu = ZYNQMP_DP_TX_DEF_TRANSFER_UNIT_SIZE;
+ u32 bw, vid_kbytes, avg_bytes_per_tu, init_wait;
+
+ /* Use the max transfer unit size (default) */
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_TRANSFER_UNIT_SIZE, tu);
+
+ vid_kbytes = mode->clock * (dp->config.bpp / 8);
+ bw = drm_dp_bw_code_to_link_rate(dp->mode.bw_code);
+ avg_bytes_per_tu = vid_kbytes * tu / (dp->mode.lane_cnt * bw / 1000);
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_MIN_BYTES_PER_TU,
+ avg_bytes_per_tu / 1000);
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_FRAC_BYTES_PER_TU,
+ avg_bytes_per_tu % 1000);
+
+ /* Configure the initial wait cycle based on transfer unit size */
+ if (tu < (avg_bytes_per_tu / 1000))
+ init_wait = 0;
+ else if ((avg_bytes_per_tu / 1000) <= 4)
+ init_wait = tu;
+ else
+ init_wait = tu - avg_bytes_per_tu / 1000;
+
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_INIT_WAIT, init_wait);
+}
+
+/**
+ * zynqmp_dp_encoder_mode_set_stream - Configure the main stream
+ * @dp: DisplayPort IP core structure
+ * @mode: requested display mode
+ *
+ * Configure the main stream based on the requested mode @mode. Calculation is
+ * based on IP core specification.
+ */
+void zynqmp_dp_encoder_mode_set_stream(struct zynqmp_dp *dp,
+ struct drm_display_mode *mode)
+{
+ void __iomem *iomem = dp->iomem;
+ u8 lane_cnt = dp->mode.lane_cnt;
+ u32 reg, wpl;
+ unsigned int rate;
+
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_MAIN_STREAM_HTOTAL, mode->htotal);
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_MAIN_STREAM_VTOTAL, mode->vtotal);
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_MAIN_STREAM_POLARITY,
+ (!!(mode->flags & DRM_MODE_FLAG_PVSYNC) <<
+ ZYNQMP_DP_TX_MAIN_STREAM_POLARITY_VSYNC_SHIFT) |
+ (!!(mode->flags & DRM_MODE_FLAG_PHSYNC) <<
+ ZYNQMP_DP_TX_MAIN_STREAM_POLARITY_HSYNC_SHIFT));
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_MAIN_STREAM_HSWIDTH,
+ mode->hsync_end - mode->hsync_start);
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_MAIN_STREAM_VSWIDTH,
+ mode->vsync_end - mode->vsync_start);
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_MAIN_STREAM_HRES, mode->hdisplay);
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_MAIN_STREAM_VRES, mode->vdisplay);
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_MAIN_STREAM_HSTART,
+ mode->htotal - mode->hsync_start);
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_MAIN_STREAM_VSTART,
+ mode->vtotal - mode->vsync_start);
+
+ /* In synchronous mode, set the diviers */
+ if (dp->config.misc0 & ZYNQMP_DP_TX_MAIN_STREAM_MISC0_SYNC) {
+ reg = drm_dp_bw_code_to_link_rate(dp->mode.bw_code);
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_N_VID, reg);
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_M_VID, mode->clock);
+ rate = zynqmp_disp_get_aud_clk_rate(dp->dpsub->disp);
+ if (rate) {
+ dev_dbg(dp->dev, "Audio rate: %d\n", rate / 512);
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_AUDIO_N_AUD, reg);
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_AUDIO_M_AUD,
+ rate / 1000);
+ }
+ }
+
+ /* Only 2 channel audio is supported now */
+ if (zynqmp_disp_aud_enabled(dp->dpsub->disp))
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_AUDIO_CHANNELS, 1);
+
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_USER_PIXEL_WIDTH, 1);
+
+ /* Translate to the native 16 bit datapath based on IP core spec */
+ wpl = (mode->hdisplay * dp->config.bpp + 15) / 16;
+ reg = wpl + wpl % lane_cnt - lane_cnt;
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_USER_DATA_CNT_PER_LANE, reg);
+}
+
+/*
+ * DRM connector functions
+ */
+
+static enum drm_connector_status
+zynqmp_dp_connector_detect(struct drm_connector *connector, bool force)
+{
+ struct zynqmp_dp *dp = connector_to_dp(connector);
+ struct zynqmp_dp_link_config *link_config = &dp->link_config;
+ u32 state, i;
+ int ret;
+
+ /*
+ * This is from heuristic. It takes some delay (ex, 100 ~ 500 msec) to
+ * get the HPD signal with some monitors.
+ */
+ for (i = 0; i < 10; i++) {
+ state = zynqmp_dp_read(dp->iomem,
+ ZYNQMP_DP_TX_INTR_SIGNAL_STATE);
+ if (state & ZYNQMP_DP_TX_INTR_SIGNAL_STATE_HPD)
+ break;
+ msleep(100);
+ }
+
+ if (state & ZYNQMP_DP_TX_INTR_SIGNAL_STATE_HPD) {
+ ret = drm_dp_dpcd_read(&dp->aux, 0x0, dp->dpcd,
+ sizeof(dp->dpcd));
+ if (ret < 0) {
+ dev_dbg(dp->dev, "DPCD read failes");
+ goto disconnected;
+ }
+
+ link_config->max_rate = min_t(int,
+ drm_dp_max_link_rate(dp->dpcd),
+ DP_HIGH_BIT_RATE2);
+ link_config->max_lanes = min_t(u8,
+ drm_dp_max_lane_count(dp->dpcd),
+ dp->num_lanes);
+
+ dp->status = connector_status_connected;
+ return connector_status_connected;
+ }
+
+disconnected:
+ dp->status = connector_status_disconnected;
+ return connector_status_disconnected;
+}
+
+static int zynqmp_dp_connector_get_modes(struct drm_connector *connector)
+{
+ struct zynqmp_dp *dp = connector_to_dp(connector);
+ struct edid *edid;
+ int ret;
+
+ edid = drm_get_edid(connector, &dp->aux.ddc);
+ if (!edid)
+ return 0;
+
+ drm_mode_connector_update_edid_property(connector, edid);
+ ret = drm_add_edid_modes(connector, edid);
+ kfree(edid);
+
+ return ret;
+}
+
+static struct drm_encoder *
+zynqmp_dp_connector_best_encoder(struct drm_connector *connector)
+{
+ struct zynqmp_dp *dp = connector_to_dp(connector);
+
+ return &dp->encoder;
+}
+
+static int zynqmp_dp_connector_mode_valid(struct drm_connector *connector,
+ struct drm_display_mode *mode)
+{
+ struct zynqmp_dp *dp = connector_to_dp(connector);
+ u8 max_lanes = dp->link_config.max_lanes;
+ u8 bpp = dp->config.bpp;
+ int max_rate = dp->link_config.max_rate;
+ int rate;
+
+ if (mode->clock > ZYNQMP_MAX_FREQ) {
+ dev_dbg(dp->dev, "filtered the mode, %s,for high pixel rate\n",
+ mode->name);
+ drm_mode_debug_printmodeline(mode);
+ return MODE_CLOCK_HIGH;
+ }
+
+ /* Check with link rate and lane count */
+ rate = zynqmp_dp_max_rate(max_rate, max_lanes, bpp);
+ if (mode->clock > rate) {
+ dev_dbg(dp->dev, "filtered the mode, %s,for high pixel rate\n",
+ mode->name);
+ drm_mode_debug_printmodeline(mode);
+ return MODE_CLOCK_HIGH;
+ }
+
+ return MODE_OK;
+}
+
+static void zynqmp_dp_connector_destroy(struct drm_connector *connector)
+{
+ drm_connector_unregister(connector);
+ drm_connector_cleanup(connector);
+}
+
+static const struct drm_connector_funcs zynqmp_dp_connector_funcs = {
+ .detect = zynqmp_dp_connector_detect,
+ .fill_modes = drm_helper_probe_single_connector_modes,
+ .destroy = zynqmp_dp_connector_destroy,
+ .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
+ .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
+ .reset = drm_atomic_helper_connector_reset,
+};
+
+static struct drm_connector_helper_funcs zynqmp_dp_connector_helper_funcs = {
+ .get_modes = zynqmp_dp_connector_get_modes,
+ .best_encoder = zynqmp_dp_connector_best_encoder,
+ .mode_valid = zynqmp_dp_connector_mode_valid,
+};
+
+/*
+ * DRM encoder functions
+ */
+
+static void zynqmp_dp_encoder_enable(struct drm_encoder *encoder)
+{
+ struct zynqmp_dp *dp = encoder_to_dp(encoder);
+ void __iomem *iomem = dp->iomem;
+ unsigned int i;
+ int ret = 0;
+
+ pm_runtime_get_sync(dp->dev);
+ dp->enabled = true;
+ zynqmp_dp_init_aux(dp);
+ zynqmp_dp_update_misc(dp);
+ if (zynqmp_disp_aud_enabled(dp->dpsub->disp))
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_AUDIO_CONTROL, 1);
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_PHY_POWER_DOWN, 0);
+ if (dp->status == connector_status_connected) {
+ for (i = 0; i < 3; i++) {
+ ret = drm_dp_dpcd_writeb(&dp->aux, DP_SET_POWER,
+ DP_SET_POWER_D0);
+ if (ret == 1)
+ break;
+ usleep_range(300, 500);
+ }
+ /* Some monitors take time to wake up properly */
+ msleep(zynqmp_dp_power_on_delay_ms);
+ }
+ if (ret != 1)
+ dev_dbg(dp->dev, "DP aux failed\n");
+ else
+ zynqmp_dp_train_loop(dp);
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_SW_RESET,
+ ZYNQMP_DP_TX_SW_RESET_ALL);
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_ENABLE_MAIN_STREAM, 1);
+}
+
+static void zynqmp_dp_encoder_disable(struct drm_encoder *encoder)
+{
+ struct zynqmp_dp *dp = encoder_to_dp(encoder);
+ void __iomem *iomem = dp->iomem;
+
+ dp->enabled = false;
+ cancel_delayed_work(&dp->hpd_work);
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_ENABLE_MAIN_STREAM, 0);
+ drm_dp_dpcd_writeb(&dp->aux, DP_SET_POWER, DP_SET_POWER_D3);
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_PHY_POWER_DOWN,
+ ZYNQMP_DP_TX_PHY_POWER_DOWN_ALL);
+ if (zynqmp_disp_aud_enabled(dp->dpsub->disp))
+ zynqmp_dp_write(iomem, ZYNQMP_DP_TX_AUDIO_CONTROL, 0);
+ pm_runtime_put_sync(dp->dev);
+}
+
+static void
+zynqmp_dp_encoder_atomic_mode_set(struct drm_encoder *encoder,
+ struct drm_crtc_state *crtc_state,
+ struct drm_connector_state *connector_state)
+{
+ struct zynqmp_dp *dp = encoder_to_dp(encoder);
+ struct drm_display_mode *mode = &crtc_state->mode;
+ struct drm_display_mode *adjusted_mode = &crtc_state->adjusted_mode;
+ u8 max_lanes = dp->link_config.max_lanes;
+ u8 bpp = dp->config.bpp;
+ int rate, max_rate = dp->link_config.max_rate;
+ int ret;
+
+ /* Check again as bpp or format might have been chagned */
+ rate = zynqmp_dp_max_rate(max_rate, max_lanes, bpp);
+ if (mode->clock > rate) {
+ dev_err(dp->dev, "the mode, %s,has too high pixel rate\n",
+ mode->name);
+ drm_mode_debug_printmodeline(mode);
+ }
+
+ ret = zynqmp_dp_mode_configure(dp, adjusted_mode->clock, 0);
+ if (ret < 0)
+ return;
+
+ zynqmp_dp_encoder_mode_set_transfer_unit(dp, adjusted_mode);
+}
+
+#define ZYNQMP_DP_MIN_H_BACKPORCH 20
+
+static int
+zynqmp_dp_encoder_atomic_check(struct drm_encoder *encoder,
+ struct drm_crtc_state *crtc_state,
+ struct drm_connector_state *conn_state)
+{
+ struct drm_display_mode *mode = &crtc_state->mode;
+ struct drm_display_mode *adjusted_mode = &crtc_state->adjusted_mode;
+ int diff = mode->htotal - mode->hsync_end;
+
+ /*
+ * ZynqMP DP requires horizontal backporch to be greater than 12.
+ * This limitation may not be compatible with the sink device.
+ */
+ if (diff < ZYNQMP_DP_MIN_H_BACKPORCH) {
+ int vrefresh = (adjusted_mode->clock * 1000) /
+ (adjusted_mode->vtotal * adjusted_mode->htotal);
+
+ dev_dbg(encoder->dev->dev, "hbackporch adjusted: %d to %d",
+ diff, ZYNQMP_DP_MIN_H_BACKPORCH - diff);
+ diff = ZYNQMP_DP_MIN_H_BACKPORCH - diff;
+ adjusted_mode->htotal += diff;
+ adjusted_mode->clock = adjusted_mode->vtotal *
+ adjusted_mode->htotal * vrefresh / 1000;
+ }
+
+ return 0;
+}
+
+static const struct drm_encoder_funcs zynqmp_dp_encoder_funcs = {
+ .destroy = drm_encoder_cleanup,
+};
+
+static const struct drm_encoder_helper_funcs zynqmp_dp_encoder_helper_funcs = {
+ .enable = zynqmp_dp_encoder_enable,
+ .disable = zynqmp_dp_encoder_disable,
+ .atomic_mode_set = zynqmp_dp_encoder_atomic_mode_set,
+ .atomic_check = zynqmp_dp_encoder_atomic_check,
+};
+
+/*
+ * Component functions
+ */
+
+static void zynqmp_dp_hpd_work_func(struct work_struct *work)
+{
+ struct zynqmp_dp *dp;
+
+ dp = container_of(work, struct zynqmp_dp, hpd_work.work);
+
+ if (dp->drm)
+ drm_helper_hpd_irq_event(dp->drm);
+}
+
+int zynqmp_dp_bind(struct device *dev, struct device *master, void *data)
+{
+ struct zynqmp_dpsub *dpsub = dev_get_drvdata(dev);
+ struct zynqmp_dp *dp = dpsub->dp;
+ struct drm_encoder *encoder = &dp->encoder;
+ struct drm_connector *connector = &dp->connector;
+ struct drm_device *drm = data;
+ struct device_node *port;
+ int ret;
+
+ encoder->possible_crtcs |= zynqmp_disp_get_crtc_mask(dpsub->disp);
+ for_each_child_of_node(dev->of_node, port) {
+ if (!port->name || of_node_cmp(port->name, "port"))
+ continue;
+ encoder->possible_crtcs |= drm_of_find_possible_crtcs(drm,
+ port);
+ }
+ drm_encoder_init(drm, encoder, &zynqmp_dp_encoder_funcs,
+ DRM_MODE_ENCODER_TMDS, NULL);
+ drm_encoder_helper_add(encoder, &zynqmp_dp_encoder_helper_funcs);
+
+ connector->polled = DRM_CONNECTOR_POLL_HPD;
+ ret = drm_connector_init(encoder->dev, connector,
+ &zynqmp_dp_connector_funcs,
+ DRM_MODE_CONNECTOR_DisplayPort);
+ if (ret) {
+ dev_err(dp->dev, "failed to initialize the drm connector");
+ goto error_encoder;
+ }
+
+ drm_connector_helper_add(connector, &zynqmp_dp_connector_helper_funcs);
+ drm_connector_register(connector);
+ drm_mode_connector_attach_encoder(connector, encoder);
+ connector->dpms = DRM_MODE_DPMS_OFF;
+
+ dp->drm = drm;
+ dp->config.misc0 &= ~ZYNQMP_DP_TX_MAIN_STREAM_MISC0_SYNC;
+ ret = zynqmp_dp_set_bpc(dp, 8);
+ zynqmp_dp_update_bpp(dp);
+
+ /* This enables interrupts, so should be called after DRM init */
+ ret = zynqmp_dp_init_aux(dp);
+ if (ret) {
+ dev_err(dp->dev, "failed to initialize DP aux");
+ goto error_connector;
+ }
+ INIT_DELAYED_WORK(&dp->hpd_work, zynqmp_dp_hpd_work_func);
+
+ return 0;
+
+error_connector:
+ zynqmp_dp_connector_destroy(&dp->connector);
+error_encoder:
+ drm_encoder_cleanup(&dp->encoder);
+ return ret;
+}
+
+void zynqmp_dp_unbind(struct device *dev, struct device *master, void *data)
+{
+ struct zynqmp_dpsub *dpsub = dev_get_drvdata(dev);
+ struct zynqmp_dp *dp = dpsub->dp;
+
+ cancel_delayed_work_sync(&dp->hpd_work);
+ disable_irq(dp->irq);
+ zynqmp_dp_exit_aux(dp);
+ zynqmp_dp_connector_destroy(&dp->connector);
+ drm_encoder_cleanup(&dp->encoder);
+}
+
+/*
+ * Platform functions
+ */
+
+static irqreturn_t zynqmp_dp_irq_handler(int irq, void *data)
+{
+ struct zynqmp_dp *dp = (struct zynqmp_dp *)data;
+ u32 status, mask;
+
+ status = zynqmp_dp_read(dp->iomem, ZYNQMP_DP_SUB_TX_INTR_STATUS);
+ mask = zynqmp_dp_read(dp->iomem, ZYNQMP_DP_SUB_TX_INTR_MASK);
+ if (!(status & ~mask))
+ return IRQ_NONE;
+
+ /* dbg for diagnostic, but not much that the driver can do */
+ if (status & ZYNQMP_DP_TX_INTR_CHBUF_UNDERFLW_MASK)
+ dev_dbg_ratelimited(dp->dev, "underflow interrupt\n");
+ if (status & ZYNQMP_DP_TX_INTR_CHBUF_OVERFLW_MASK)
+ dev_dbg_ratelimited(dp->dev, "overflow interrupt\n");
+
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_SUB_TX_INTR_STATUS, status);
+
+ /* The DP vblank will not be enabled with remote crtc device */
+ if (status & ZYNQMP_DP_TX_INTR_VBLANK_START)
+ zynqmp_disp_handle_vblank(dp->dpsub->disp);
+
+ if (status & ZYNQMP_DP_TX_INTR_HPD_EVENT)
+ schedule_delayed_work(&dp->hpd_work, 0);
+
+ if (status & ZYNQMP_DP_TX_INTR_HPD_IRQ) {
+ int ret;
+ u8 status[DP_LINK_STATUS_SIZE + 2];
+
+ ret = drm_dp_dpcd_read(&dp->aux, DP_SINK_COUNT, status,
+ DP_LINK_STATUS_SIZE + 2);
+ if (ret < 0)
+ goto handled;
+
+ if (status[4] & DP_LINK_STATUS_UPDATED ||
+ !drm_dp_clock_recovery_ok(&status[2], dp->mode.lane_cnt) ||
+ !drm_dp_channel_eq_ok(&status[2], dp->mode.lane_cnt)) {
+ zynqmp_dp_train_loop(dp);
+ }
+ }
+
+handled:
+ return IRQ_HANDLED;
+}
+
+int zynqmp_dp_probe(struct platform_device *pdev)
+{
+ struct zynqmp_dpsub *dpsub;
+ struct zynqmp_dp *dp;
+ struct resource *res;
+ unsigned int i;
+ int irq, ret;
+
+ dp = devm_kzalloc(&pdev->dev, sizeof(*dp), GFP_KERNEL);
+ if (!dp)
+ return -ENOMEM;
+
+ dp->dpms = DRM_MODE_DPMS_OFF;
+ dp->status = connector_status_disconnected;
+ dp->dev = &pdev->dev;
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dp");
+ dp->iomem = devm_ioremap_resource(dp->dev, res);
+ if (IS_ERR(dp->iomem))
+ return PTR_ERR(dp->iomem);
+
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_PHY_POWER_DOWN,
+ ZYNQMP_DP_TX_PHY_POWER_DOWN_ALL);
+ zynqmp_dp_set(dp->iomem, ZYNQMP_DP_TX_PHY_CONFIG,
+ ZYNQMP_DP_TX_PHY_CONFIG_ALL_RESET);
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_FORCE_SCRAMBLER_RESET, 1);
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_ENABLE, 0);
+
+ dp->num_lanes = 2;
+ for (i = 0; i < ZYNQMP_DP_MAX_LANES; i++) {
+ char phy_name[16];
+
+ snprintf(phy_name, sizeof(phy_name), "dp-phy%d", i);
+ dp->phy[i] = devm_phy_get(dp->dev, phy_name);
+ if (IS_ERR(dp->phy[i])) {
+ /* 2nd lane is optional */
+ if (i == 0 || PTR_ERR(dp->phy[i]) != -ENODEV) {
+ dev_err(dp->dev, "failed to get phy lane\n");
+ ret = PTR_ERR(dp->phy[i]);
+ dp->phy[i] = NULL;
+ return ret;
+ }
+ dp->phy[i] = NULL;
+ dp->num_lanes = 1;
+ }
+ }
+
+ ret = zynqmp_dp_init_phy(dp);
+ if (ret)
+ goto error_phy;
+
+ dp->aux.name = "ZynqMP DP AUX";
+ dp->aux.dev = dp->dev;
+ dp->aux.transfer = zynqmp_dp_aux_transfer;
+ ret = drm_dp_aux_register(&dp->aux);
+ if (ret < 0) {
+ dev_err(dp->dev, "failed to initialize DP aux\n");
+ goto error;
+ }
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ ret = irq;
+ goto error;
+ }
+
+ ret = devm_request_threaded_irq(dp->dev, irq, NULL,
+ zynqmp_dp_irq_handler, IRQF_ONESHOT,
+ dev_name(dp->dev), dp);
+ if (ret < 0)
+ goto error;
+ dp->irq = irq;
+
+ dpsub = platform_get_drvdata(pdev);
+ dpsub->dp = dp;
+ dp->dpsub = dpsub;
+
+ return 0;
+
+error:
+ drm_dp_aux_unregister(&dp->aux);
+error_phy:
+ zynqmp_dp_exit_phy(dp);
+ return ret;
+}
+
+int zynqmp_dp_remove(struct platform_device *pdev)
+{
+ struct zynqmp_dpsub *dpsub = platform_get_drvdata(pdev);
+ struct zynqmp_dp *dp = dpsub->dp;
+
+ zynqmp_dp_write(dp->iomem, ZYNQMP_DP_TX_ENABLE, 0);
+ drm_dp_aux_unregister(&dp->aux);
+ zynqmp_dp_exit_phy(dp);
+ dpsub->dp = NULL;
+
+ return 0;
+}
diff --git a/drivers/gpu/drm/xlnx/zynqmp_dp.h b/drivers/gpu/drm/xlnx/zynqmp_dp.h
new file mode 100644
index 0000000..2d7cb8a
--- /dev/null
+++ b/drivers/gpu/drm/xlnx/zynqmp_dp.h
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ZynqMP DisplayPort Driver
+ *
+ * Copyright (C) 2017 - 2018 Xilinx, Inc.
+ *
+ * Author: Hyun Woo Kwon <hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _ZYNQMP_DP_H_
+#define _ZYNQMP_DP_H_
+
+struct zynqmp_dp;
+struct drm_display_mode;
+
+const int zynqmp_dp_set_color(struct zynqmp_dp *dp, const char *color);
+void zynqmp_dp_enable_vblank(struct zynqmp_dp *dp);
+void zynqmp_dp_disable_vblank(struct zynqmp_dp *dp);
+void zynqmp_dp_encoder_mode_set_stream(struct zynqmp_dp *dp,
+ struct drm_display_mode *mode);
+
+int zynqmp_dp_bind(struct device *dev, struct device *master, void *data);
+void zynqmp_dp_unbind(struct device *dev, struct device *master, void *data);
+
+int zynqmp_dp_probe(struct platform_device *pdev);
+int zynqmp_dp_remove(struct platform_device *pdev);
+
+#endif /* _ZYNQMP_DP_H_ */
--
2.7.4
This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH v3 6/8] drm: xlnx: ZynqMP DP subsystem DRM KMS driver
[not found] ` <1516067831-11382-1-git-send-email-hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
` (3 preceding siblings ...)
2018-01-16 1:57 ` [PATCH v3 5/8] drm: xlnx: DRM KMS driver for Xilinx ZynqMP DisplayPort Hyun Kwon
@ 2018-01-16 1:57 ` Hyun Kwon
4 siblings, 0 replies; 17+ messages in thread
From: Hyun Kwon @ 2018-01-16 1:57 UTC (permalink / raw)
To: dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW,
devicetree-u79uwXL29TY76Z2rM5mHXA
Cc: Michal Simek, Rob Herring, Daniel Vetter, Laurent Pinchart, Hyun Kwon
This is a wrapper around the ZynqMP Display and DisplayPort drivers.
Signed-off-by: Hyun Kwon <hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
---
- Change the SPDX identifier format
---
---
drivers/gpu/drm/xlnx/Kconfig | 11 +++
drivers/gpu/drm/xlnx/Makefile | 3 +
drivers/gpu/drm/xlnx/zynqmp_dpsub.c | 149 ++++++++++++++++++++++++++++++++++++
drivers/gpu/drm/xlnx/zynqmp_dpsub.h | 27 +++++++
4 files changed, 190 insertions(+)
create mode 100644 drivers/gpu/drm/xlnx/zynqmp_dpsub.c
create mode 100644 drivers/gpu/drm/xlnx/zynqmp_dpsub.h
diff --git a/drivers/gpu/drm/xlnx/Kconfig b/drivers/gpu/drm/xlnx/Kconfig
index 19fd7cd..7c5529c 100644
--- a/drivers/gpu/drm/xlnx/Kconfig
+++ b/drivers/gpu/drm/xlnx/Kconfig
@@ -10,3 +10,14 @@ config DRM_XLNX
display pipeline using Xilinx IPs in FPGA. This module
provides the kernel mode setting functionalities
for Xilinx display drivers.
+
+config DRM_ZYNQMP_DPSUB
+ tristate "ZynqMP DP Subsystem Driver"
+ depends on ARCH_ZYNQMP && OF && DRM_XLNX && COMMON_CLK
+ select DMA_ENGINE
+ select GENERIC_PHY
+ help
+ DRM KMS driver for ZynqMP DP Subsystem controller. Choose
+ this option if you have a Xilinx ZynqMP SoC with DisplayPort
+ subsystem. The driver provides the kernel mode setting
+ functionlaities for ZynqMP DP subsystem.
diff --git a/drivers/gpu/drm/xlnx/Makefile b/drivers/gpu/drm/xlnx/Makefile
index c60a281..064a05a 100644
--- a/drivers/gpu/drm/xlnx/Makefile
+++ b/drivers/gpu/drm/xlnx/Makefile
@@ -1,2 +1,5 @@
xlnx_drm-objs += xlnx_crtc.o xlnx_drv.o xlnx_fb.o xlnx_gem.o
obj-$(CONFIG_DRM_XLNX) += xlnx_drm.o
+
+zynqmp-dpsub-objs += zynqmp_disp.o zynqmp_dpsub.o zynqmp_dp.o
+obj-$(CONFIG_DRM_ZYNQMP_DPSUB) += zynqmp-dpsub.o
diff --git a/drivers/gpu/drm/xlnx/zynqmp_dpsub.c b/drivers/gpu/drm/xlnx/zynqmp_dpsub.c
new file mode 100644
index 0000000..517b492
--- /dev/null
+++ b/drivers/gpu/drm/xlnx/zynqmp_dpsub.c
@@ -0,0 +1,149 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ZynqMP DP Subsystem Driver
+ *
+ * Copyright (C) 2017 - 2018 Xilinx, Inc.
+ *
+ * Author: Hyun Woo Kwon <hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/component.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+
+#include "zynqmp_disp.h"
+#include "zynqmp_dp.h"
+#include "zynqmp_dpsub.h"
+
+static int
+zynqmp_dpsub_bind(struct device *dev, struct device *master, void *data)
+{
+ int ret;
+
+ ret = zynqmp_disp_bind(dev, master, data);
+ if (ret)
+ return ret;
+
+ /* zynqmp_disp should bind first, so zynqmp_dp encoder can find crtc */
+ ret = zynqmp_dp_bind(dev, master, data);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static void
+zynqmp_dpsub_unbind(struct device *dev, struct device *master, void *data)
+{
+ zynqmp_dp_unbind(dev, master, data);
+ zynqmp_disp_unbind(dev, master, data);
+}
+
+static const struct component_ops zynqmp_dpsub_component_ops = {
+ .bind = zynqmp_dpsub_bind,
+ .unbind = zynqmp_dpsub_unbind,
+};
+
+static int zynqmp_dpsub_probe(struct platform_device *pdev)
+{
+ struct zynqmp_dpsub *dpsub;
+ int ret;
+
+ dpsub = devm_kzalloc(&pdev->dev, sizeof(*dpsub), GFP_KERNEL);
+ if (!dpsub)
+ return -ENOMEM;
+
+ /* Sub-driver will access dpsub from drvdata */
+ platform_set_drvdata(pdev, dpsub);
+ pm_runtime_enable(&pdev->dev);
+
+ /*
+ * DP should be probed first so that the zynqmp_disp can set the output
+ * format accordingly.
+ */
+ ret = zynqmp_dp_probe(pdev);
+ if (ret)
+ goto err_pm;
+
+ ret = zynqmp_disp_probe(pdev);
+ if (ret)
+ goto err_dp;
+
+ ret = component_add(&pdev->dev, &zynqmp_dpsub_component_ops);
+ if (ret)
+ goto err_disp;
+
+ /* Populate the sound child nodes */
+ ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to populate child nodes\n");
+ goto err_component;
+ }
+
+ dev_info(&pdev->dev, "ZynqMP DisplayPort Subsystem driver probed");
+
+ return 0;
+
+err_component:
+ component_del(&pdev->dev, &zynqmp_dpsub_component_ops);
+err_disp:
+ zynqmp_disp_remove(pdev);
+err_dp:
+ zynqmp_dp_remove(pdev);
+err_pm:
+ pm_runtime_disable(&pdev->dev);
+ return ret;
+}
+
+static int zynqmp_dpsub_remove(struct platform_device *pdev)
+{
+ int err, ret = 0;
+
+ of_platform_depopulate(&pdev->dev);
+ component_del(&pdev->dev, &zynqmp_dpsub_component_ops);
+
+ err = zynqmp_disp_remove(pdev);
+ if (err)
+ ret = -EIO;
+
+ err = zynqmp_dp_remove(pdev);
+ if (err)
+ ret = -EIO;
+
+ pm_runtime_disable(&pdev->dev);
+
+ return err;
+}
+
+static const struct of_device_id zynqmp_dpsub_of_match[] = {
+ { .compatible = "xlnx,zynqmp-dpsub-1.7", },
+ { /* end of table */ },
+};
+MODULE_DEVICE_TABLE(of, zynqmp_dpsub_of_match);
+
+static struct platform_driver zynqmp_dpsub_driver = {
+ .probe = zynqmp_dpsub_probe,
+ .remove = zynqmp_dpsub_remove,
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = "zynqmp-display",
+ .of_match_table = zynqmp_dpsub_of_match,
+ },
+};
+
+module_platform_driver(zynqmp_dpsub_driver);
+
+MODULE_AUTHOR("Xilinx, Inc.");
+MODULE_DESCRIPTION("ZynqMP DP Subsystem Driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/gpu/drm/xlnx/zynqmp_dpsub.h b/drivers/gpu/drm/xlnx/zynqmp_dpsub.h
new file mode 100644
index 0000000..2c1455f
--- /dev/null
+++ b/drivers/gpu/drm/xlnx/zynqmp_dpsub.h
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ZynqMP DPSUB Subsystem Driver
+ *
+ * Copyright (C) 2017 - 2018 Xilinx, Inc.
+ *
+ * Author: Hyun Woo Kwon <hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _ZYNQMP_DPSUB_H_
+#define _ZYNQMP_DPSUB_H_
+
+struct zynqmp_dpsub {
+ struct zynqmp_dp *dp;
+ struct zynqmp_disp *disp;
+};
+
+#endif /* _ZYNQMP_DPSUB_H_ */
--
2.7.4
This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH v3 7/8] drm: xlnx: zynqmp_disp: Add drm properties
2018-01-16 1:57 [PATCH v3 1/8] dt-bindings: display: xlnx: Add bindings for Xilinx display pipeline Hyun Kwon
[not found] ` <1516067831-11382-1-git-send-email-hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
@ 2018-01-16 1:57 ` Hyun Kwon
2018-01-16 1:57 ` [PATCH v3 8/8] drm: xlnx: zynqmp_dp: " Hyun Kwon
2018-01-19 23:32 ` [PATCH v3 1/8] dt-bindings: display: xlnx: Add bindings for Xilinx display pipeline Rob Herring
3 siblings, 0 replies; 17+ messages in thread
From: Hyun Kwon @ 2018-01-16 1:57 UTC (permalink / raw)
To: dri-devel, devicetree
Cc: Laurent Pinchart, Michal Simek, Hyun Kwon, Daniel Vetter
Add drm properties for global alpha, output color, background color,
and test pattern generation.
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
---
v2
- Split from the original patch
- Some props are important feature to be included
---
---
drivers/gpu/drm/xlnx/zynqmp_disp.c | 191 +++++++++++++++++++++++++++++++++++++
1 file changed, 191 insertions(+)
diff --git a/drivers/gpu/drm/xlnx/zynqmp_disp.c b/drivers/gpu/drm/xlnx/zynqmp_disp.c
index 65519ca..3308764 100644
--- a/drivers/gpu/drm/xlnx/zynqmp_disp.c
+++ b/drivers/gpu/drm/xlnx/zynqmp_disp.c
@@ -413,12 +413,19 @@ struct zynqmp_disp_aud {
* @av_buf: AV buffer manager block
* @aud:Audio block
* @layers: layers
+ * @g_alpha_prop: global alpha property
* @alpha: current global alpha value
+ * @g_alpha_en_prop: the global alpha enable property
* @alpha_en: flag if the global alpha is enabled
+ * @color_prop: output color format property
* @color: current output color value
+ * @bg_c0_prop: 1st component of background color property
* @bg_c0: current value of 1st background color component
+ * @bg_c1_prop: 2nd component of background color property
* @bg_c1: current value of 2nd background color component
+ * @bg_c2_prop: 3rd component of background color property
* @bg_c2: current value of 3rd background color component
+ * @tpg_prop: Test Pattern Generation mode property
* @tpg_on: current TPG mode state
* @event: pending vblank event request
* @_ps_pclk: Pixel clock from PS
@@ -442,12 +449,19 @@ struct zynqmp_disp {
struct zynqmp_disp_av_buf av_buf;
struct zynqmp_disp_aud aud;
struct zynqmp_disp_layer layers[ZYNQMP_DISP_NUM_LAYERS];
+ struct drm_property *g_alpha_prop;
u32 alpha;
+ struct drm_property *g_alpha_en_prop;
bool alpha_en;
+ struct drm_property *color_prop;
unsigned int color;
+ struct drm_property *bg_c0_prop;
u32 bg_c0;
+ struct drm_property *bg_c1_prop;
u32 bg_c1;
+ struct drm_property *bg_c2_prop;
u32 bg_c2;
+ struct drm_property *tpg_prop;
bool tpg_on;
struct drm_pending_vblank_event *event;
/* Don't operate directly on _ps_ */
@@ -1621,6 +1635,21 @@ static int zynqmp_disp_layer_set_tpg(struct zynqmp_disp *disp,
}
/**
+ * zynqmp_disp_get_tpg - Get the TPG mode status
+ * @disp: Display subsystem
+ * @layer: Video layer
+ *
+ * Return if the TPG is enabled or not.
+ *
+ * Return: true if TPG is on, otherwise false
+ */
+static bool zynqmp_disp_layer_get_tpg(struct zynqmp_disp *disp,
+ struct zynqmp_disp_layer *layer)
+{
+ return disp->tpg_on;
+}
+
+/**
* zynqmp_disp_get_fmt - Get the supported DRM formats of the layer
* @disp: Display subsystem
* @layer: layer to get the formats
@@ -1937,6 +1966,19 @@ static void zynqmp_disp_set_alpha(struct zynqmp_disp *disp, u32 alpha)
}
/**
+ * zynqmp_disp_get_alpha - Get the alpha value
+ * @disp: Display subsystem
+ *
+ * Get the alpha value for blending.
+ *
+ * Return: current alpha value.
+ */
+static u32 zynqmp_disp_get_alpha(struct zynqmp_disp *disp)
+{
+ return disp->alpha;
+}
+
+/**
* zynqmp_disp_set_g_alpha - Enable/disable the global alpha blending
* @disp: Display subsystem
* @enable: flag to enable or disable alpha blending
@@ -1950,6 +1992,19 @@ static void zynqmp_disp_set_g_alpha(struct zynqmp_disp *disp, bool enable)
}
/**
+ * zynqmp_disp_get_g_alpha - Get the global alpha status
+ * @disp: Display subsystem
+ *
+ * Get the global alpha statue.
+ *
+ * Return: true if global alpha is enabled, or false.
+ */
+static bool zynqmp_disp_get_g_alpha(struct zynqmp_disp *disp)
+{
+ return disp->alpha_en;
+}
+
+/**
* zynqmp_disp_enable - Enable the Display subsystem
* @disp: Display subsystem
*
@@ -2172,9 +2227,54 @@ static void zynqmp_disp_plane_destroy(struct drm_plane *plane)
drm_plane_cleanup(plane);
}
+static int
+zynqmp_disp_plane_atomic_set_property(struct drm_plane *plane,
+ struct drm_plane_state *state,
+ struct drm_property *property, u64 val)
+{
+ struct zynqmp_disp_layer *layer = plane_to_layer(plane);
+ struct zynqmp_disp *disp = layer->disp;
+ int ret = 0;
+
+ if (property == disp->g_alpha_prop)
+ zynqmp_disp_set_alpha(disp, val);
+ else if (property == disp->g_alpha_en_prop)
+ zynqmp_disp_set_g_alpha(disp, val);
+ else if (property == disp->tpg_prop)
+ ret = zynqmp_disp_layer_set_tpg(disp, layer, val);
+ else
+ return -EINVAL;
+
+ return ret;
+}
+
+static int
+zynqmp_disp_plane_atomic_get_property(struct drm_plane *plane,
+ const struct drm_plane_state *state,
+ struct drm_property *property,
+ uint64_t *val)
+{
+ struct zynqmp_disp_layer *layer = plane_to_layer(plane);
+ struct zynqmp_disp *disp = layer->disp;
+ int ret = 0;
+
+ if (property == disp->g_alpha_prop)
+ *val = zynqmp_disp_get_alpha(disp);
+ else if (property == disp->g_alpha_en_prop)
+ *val = zynqmp_disp_get_g_alpha(disp);
+ else if (property == disp->tpg_prop)
+ *val = zynqmp_disp_layer_get_tpg(disp, layer);
+ else
+ return -EINVAL;
+
+ return ret;
+}
+
static struct drm_plane_funcs zynqmp_disp_plane_funcs = {
.update_plane = drm_atomic_helper_update_plane,
.disable_plane = drm_atomic_helper_disable_plane,
+ .atomic_set_property = zynqmp_disp_plane_atomic_set_property,
+ .atomic_get_property = zynqmp_disp_plane_atomic_get_property,
.destroy = zynqmp_disp_plane_destroy,
.reset = drm_atomic_helper_plane_reset,
.atomic_duplicate_state = drm_atomic_helper_plane_duplicate_state,
@@ -2241,6 +2341,18 @@ static int zynqmp_disp_create_plane(struct zynqmp_disp *disp)
type = DRM_PLANE_TYPE_PRIMARY;
}
+ /* Attach properties to each layers */
+ drm_object_attach_property(&layer->plane.base, disp->g_alpha_prop,
+ ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA_MAX);
+ disp->alpha = ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA_MAX;
+ /* Enable the global alpha as default */
+ drm_object_attach_property(&layer->plane.base, disp->g_alpha_en_prop,
+ true);
+ disp->alpha_en = true;
+
+ layer = &disp->layers[ZYNQMP_DISP_LAYER_VID];
+ drm_object_attach_property(&layer->plane.base, disp->tpg_prop, false);
+
return ret;
err_plane:
@@ -2429,10 +2541,60 @@ static void zynqmp_disp_crtc_destroy(struct drm_crtc *crtc)
drm_crtc_cleanup(crtc);
}
+static int
+zynqmp_disp_crtc_atomic_set_property(struct drm_crtc *crtc,
+ struct drm_crtc_state *state,
+ struct drm_property *property,
+ uint64_t val)
+{
+ struct zynqmp_disp *disp = crtc_to_disp(crtc);
+
+ /*
+ * CRTC prop values are just stored here and applied when CRTC gets
+ * enabled
+ */
+ if (property == disp->color_prop)
+ disp->color = val;
+ else if (property == disp->bg_c0_prop)
+ disp->bg_c0 = val;
+ else if (property == disp->bg_c1_prop)
+ disp->bg_c1 = val;
+ else if (property == disp->bg_c2_prop)
+ disp->bg_c2 = val;
+ else
+ return -EINVAL;
+
+ return 0;
+}
+
+static int
+zynqmp_disp_crtc_atomic_get_property(struct drm_crtc *crtc,
+ const struct drm_crtc_state *state,
+ struct drm_property *property,
+ uint64_t *val)
+{
+ struct zynqmp_disp *disp = crtc_to_disp(crtc);
+
+ if (property == disp->color_prop)
+ *val = disp->color;
+ else if (property == disp->bg_c0_prop)
+ *val = disp->bg_c0;
+ else if (property == disp->bg_c1_prop)
+ *val = disp->bg_c1;
+ else if (property == disp->bg_c2_prop)
+ *val = disp->bg_c2;
+ else
+ return -EINVAL;
+
+ return 0;
+}
+
static struct drm_crtc_funcs zynqmp_disp_crtc_funcs = {
.destroy = zynqmp_disp_crtc_destroy,
.set_config = drm_atomic_helper_set_config,
.page_flip = drm_atomic_helper_page_flip,
+ .atomic_set_property = zynqmp_disp_crtc_atomic_set_property,
+ .atomic_get_property = zynqmp_disp_crtc_atomic_get_property,
.reset = drm_atomic_helper_crtc_reset,
.atomic_duplicate_state = drm_atomic_helper_crtc_duplicate_state,
.atomic_destroy_state = drm_atomic_helper_crtc_destroy_state,
@@ -2441,12 +2603,18 @@ static struct drm_crtc_funcs zynqmp_disp_crtc_funcs = {
static void zynqmp_disp_create_crtc(struct zynqmp_disp *disp)
{
struct drm_plane *plane = &disp->layers[ZYNQMP_DISP_LAYER_GFX].plane;
+ struct drm_mode_object *obj = &disp->xlnx_crtc.crtc.base;
int ret;
ret = drm_crtc_init_with_planes(disp->drm, &disp->xlnx_crtc.crtc, plane,
NULL, &zynqmp_disp_crtc_funcs, NULL);
drm_crtc_helper_add(&disp->xlnx_crtc.crtc,
&zynqmp_disp_crtc_helper_funcs);
+ drm_object_attach_property(obj, disp->color_prop, 0);
+ zynqmp_dp_set_color(disp->dpsub->dp, zynqmp_disp_color_enum[0].name);
+ drm_object_attach_property(obj, disp->bg_c0_prop, 0);
+ drm_object_attach_property(obj, disp->bg_c1_prop, 0);
+ drm_object_attach_property(obj, disp->bg_c2_prop, 0);
disp->xlnx_crtc.enable_vblank = &zynqmp_disp_enable_vblank;
disp->xlnx_crtc.disable_vblank = &zynqmp_disp_disable_vblank;
@@ -2482,10 +2650,27 @@ int zynqmp_disp_bind(struct device *dev, struct device *master, void *data)
struct zynqmp_dpsub *dpsub = dev_get_drvdata(dev);
struct zynqmp_disp *disp = dpsub->disp;
struct drm_device *drm = data;
+ int num;
+ u64 max;
int ret;
disp->drm = drm;
+ max = ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA_MAX;
+ disp->g_alpha_prop = drm_property_create_range(drm, 0, "alpha", 0, max);
+ disp->g_alpha_en_prop = drm_property_create_bool(drm, 0,
+ "g_alpha_en");
+ num = ARRAY_SIZE(zynqmp_disp_color_enum);
+ disp->color_prop = drm_property_create_enum(drm, 0,
+ "output_color",
+ zynqmp_disp_color_enum,
+ num);
+ max = ZYNQMP_DISP_V_BLEND_BG_MAX;
+ disp->bg_c0_prop = drm_property_create_range(drm, 0, "bg_c0", 0, max);
+ disp->bg_c1_prop = drm_property_create_range(drm, 0, "bg_c1", 0, max);
+ disp->bg_c2_prop = drm_property_create_range(drm, 0, "bg_c2", 0, max);
+ disp->tpg_prop = drm_property_create_bool(drm, 0, "tpg");
+
ret = zynqmp_disp_create_plane(disp);
if (ret)
return ret;
@@ -2502,6 +2687,12 @@ void zynqmp_disp_unbind(struct device *dev, struct device *master, void *data)
zynqmp_disp_destroy_crtc(disp);
zynqmp_disp_destroy_plane(disp);
+ drm_property_destroy(disp->drm, disp->bg_c2_prop);
+ drm_property_destroy(disp->drm, disp->bg_c1_prop);
+ drm_property_destroy(disp->drm, disp->bg_c0_prop);
+ drm_property_destroy(disp->drm, disp->color_prop);
+ drm_property_destroy(disp->drm, disp->g_alpha_en_prop);
+ drm_property_destroy(disp->drm, disp->g_alpha_prop);
}
/*
--
2.7.4
This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH v3 8/8] drm: xlnx: zynqmp_dp: Add drm properties
2018-01-16 1:57 [PATCH v3 1/8] dt-bindings: display: xlnx: Add bindings for Xilinx display pipeline Hyun Kwon
[not found] ` <1516067831-11382-1-git-send-email-hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
2018-01-16 1:57 ` [PATCH v3 7/8] drm: xlnx: zynqmp_disp: Add drm properties Hyun Kwon
@ 2018-01-16 1:57 ` Hyun Kwon
2018-01-19 23:32 ` [PATCH v3 1/8] dt-bindings: display: xlnx: Add bindings for Xilinx display pipeline Rob Herring
3 siblings, 0 replies; 17+ messages in thread
From: Hyun Kwon @ 2018-01-16 1:57 UTC (permalink / raw)
To: dri-devel, devicetree
Cc: Laurent Pinchart, Michal Simek, Hyun Kwon, Daniel Vetter
Add drm properties for DisplayPort synchronous mode and bpc
configurations.
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
---
v2
- Split from the original patch
---
---
drivers/gpu/drm/xlnx/zynqmp_dp.c | 116 ++++++++++++++++++++++++++++++++++++++-
1 file changed, 114 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/xlnx/zynqmp_dp.c b/drivers/gpu/drm/xlnx/zynqmp_dp.c
index 9c9f4df..e1e8237 100644
--- a/drivers/gpu/drm/xlnx/zynqmp_dp.c
+++ b/drivers/gpu/drm/xlnx/zynqmp_dp.c
@@ -302,6 +302,8 @@ struct zynqmp_dp_config {
* struct zynqmp_dp - Xilinx DisplayPort core
* @encoder: the drm encoder structure
* @connector: the drm connector structure
+ * @sync_prop: synchronous mode property
+ * @bpc_prop: bpc mode property
* @dev: device structure
* @dpsub: Display subsystem
* @drm: DRM core
@@ -323,6 +325,8 @@ struct zynqmp_dp_config {
struct zynqmp_dp {
struct drm_encoder encoder;
struct drm_connector connector;
+ struct drm_property *sync_prop;
+ struct drm_property *bpc_prop;
struct device *dev;
struct zynqmp_dpsub *dpsub;
struct drm_device *drm;
@@ -1116,6 +1120,37 @@ static void zynqmp_dp_update_misc(struct zynqmp_dp *dp)
}
/**
+ * zynqmp_dp_set_sync_mode - Set the sync mode bit in the software misc state
+ * @dp: DisplayPort IP core structure
+ * @mode: flag if the sync mode should be on or off
+ *
+ * Set the bit in software misc state. To apply to hardware,
+ * zynqmp_dp_update_misc() should be called.
+ */
+static void zynqmp_dp_set_sync_mode(struct zynqmp_dp *dp, bool mode)
+{
+ struct zynqmp_dp_config *config = &dp->config;
+
+ if (mode)
+ config->misc0 |= ZYNQMP_DP_TX_MAIN_STREAM_MISC0_SYNC;
+ else
+ config->misc0 &= ~ZYNQMP_DP_TX_MAIN_STREAM_MISC0_SYNC;
+}
+
+/**
+ * zynqmp_dp_get_sync_mode - Get the sync mode state
+ * @dp: DisplayPort IP core structure
+ *
+ * Return: true if the sync mode is on, or false
+ */
+static bool zynqmp_dp_get_sync_mode(struct zynqmp_dp *dp)
+{
+ struct zynqmp_dp_config *config = &dp->config;
+
+ return !!(config->misc0 & ZYNQMP_DP_TX_MAIN_STREAM_MISC0_SYNC);
+}
+
+/**
* zynqmp_dp_set_bpc - Set bpc value in software misc state
* @dp: DisplayPort IP core structure
* @bpc: bits per component
@@ -1165,6 +1200,17 @@ static u8 zynqmp_dp_set_bpc(struct zynqmp_dp *dp, u8 bpc)
}
/**
+ * zynqmp_dp_get_bpc - Set bpc value from software state
+ * @dp: DisplayPort IP core structure
+ *
+ * Return: current bpc value
+ */
+static u8 zynqmp_dp_get_bpc(struct zynqmp_dp *dp)
+{
+ return dp->config.bpc;
+}
+
+/**
* zynqmp_dp_encoder_mode_set_transfer_unit - Set the transfer unit values
* @dp: DisplayPort IP core structure
* @mode: requested display mode
@@ -1368,6 +1414,51 @@ static void zynqmp_dp_connector_destroy(struct drm_connector *connector)
drm_connector_cleanup(connector);
}
+static int
+zynqmp_dp_connector_atomic_set_property(struct drm_connector *connector,
+ struct drm_connector_state *state,
+ struct drm_property *property,
+ uint64_t val)
+{
+ struct zynqmp_dp *dp = connector_to_dp(connector);
+ int ret;
+
+ if (property == dp->sync_prop) {
+ zynqmp_dp_set_sync_mode(dp, val);
+ } else if (property == dp->bpc_prop) {
+ u8 bpc;
+
+ bpc = zynqmp_dp_set_bpc(dp, val);
+ if (bpc) {
+ drm_object_property_set_value(&connector->base,
+ property, bpc);
+ ret = -EINVAL;
+ }
+ } else {
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int
+zynqmp_dp_connector_atomic_get_property(struct drm_connector *connector,
+ const struct drm_connector_state *state,
+ struct drm_property *property,
+ uint64_t *val)
+{
+ struct zynqmp_dp *dp = connector_to_dp(connector);
+
+ if (property == dp->sync_prop)
+ *val = zynqmp_dp_get_sync_mode(dp);
+ else if (property == dp->bpc_prop)
+ *val = zynqmp_dp_get_bpc(dp);
+ else
+ return -EINVAL;
+
+ return 0;
+}
+
static const struct drm_connector_funcs zynqmp_dp_connector_funcs = {
.detect = zynqmp_dp_connector_detect,
.fill_modes = drm_helper_probe_single_connector_modes,
@@ -1375,6 +1466,8 @@ static const struct drm_connector_funcs zynqmp_dp_connector_funcs = {
.atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
.atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
.reset = drm_atomic_helper_connector_reset,
+ .atomic_set_property = zynqmp_dp_connector_atomic_set_property,
+ .atomic_get_property = zynqmp_dp_connector_atomic_get_property,
};
static struct drm_connector_helper_funcs zynqmp_dp_connector_helper_funcs = {
@@ -1520,6 +1613,13 @@ static void zynqmp_dp_hpd_work_func(struct work_struct *work)
drm_helper_hpd_irq_event(dp->drm);
}
+static struct drm_prop_enum_list zynqmp_dp_bpc_enum[] = {
+ { 6, "6BPC" },
+ { 8, "8BPC" },
+ { 10, "10BPC" },
+ { 12, "12BPC" },
+};
+
int zynqmp_dp_bind(struct device *dev, struct device *master, void *data)
{
struct zynqmp_dpsub *dpsub = dev_get_drvdata(dev);
@@ -1556,21 +1656,31 @@ int zynqmp_dp_bind(struct device *dev, struct device *master, void *data)
connector->dpms = DRM_MODE_DPMS_OFF;
dp->drm = drm;
+ dp->sync_prop = drm_property_create_bool(drm, 0, "sync");
+ dp->bpc_prop = drm_property_create_enum(drm, 0, "bpc",
+ zynqmp_dp_bpc_enum,
+ ARRAY_SIZE(zynqmp_dp_bpc_enum));
+
dp->config.misc0 &= ~ZYNQMP_DP_TX_MAIN_STREAM_MISC0_SYNC;
+ drm_object_attach_property(&connector->base, dp->sync_prop, false);
ret = zynqmp_dp_set_bpc(dp, 8);
+ drm_object_attach_property(&connector->base, dp->bpc_prop,
+ ret ? ret : 8);
zynqmp_dp_update_bpp(dp);
/* This enables interrupts, so should be called after DRM init */
ret = zynqmp_dp_init_aux(dp);
if (ret) {
dev_err(dp->dev, "failed to initialize DP aux");
- goto error_connector;
+ goto error_prop;
}
INIT_DELAYED_WORK(&dp->hpd_work, zynqmp_dp_hpd_work_func);
return 0;
-error_connector:
+error_prop:
+ drm_property_destroy(dp->drm, dp->bpc_prop);
+ drm_property_destroy(dp->drm, dp->sync_prop);
zynqmp_dp_connector_destroy(&dp->connector);
error_encoder:
drm_encoder_cleanup(&dp->encoder);
@@ -1585,6 +1695,8 @@ void zynqmp_dp_unbind(struct device *dev, struct device *master, void *data)
cancel_delayed_work_sync(&dp->hpd_work);
disable_irq(dp->irq);
zynqmp_dp_exit_aux(dp);
+ drm_property_destroy(dp->drm, dp->bpc_prop);
+ drm_property_destroy(dp->drm, dp->sync_prop);
zynqmp_dp_connector_destroy(&dp->connector);
drm_encoder_cleanup(&dp->encoder);
}
--
2.7.4
This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 17+ messages in thread
* Re: [PATCH v3 2/8] drm: xlnx: Xilinx DRM KMS driver
[not found] ` <1516067831-11382-2-git-send-email-hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
@ 2018-01-17 8:11 ` Daniel Vetter
0 siblings, 0 replies; 17+ messages in thread
From: Daniel Vetter @ 2018-01-17 8:11 UTC (permalink / raw)
To: Hyun Kwon
Cc: dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW,
devicetree-u79uwXL29TY76Z2rM5mHXA, Michal Simek, Rob Herring,
Daniel Vetter, Laurent Pinchart
On Mon, Jan 15, 2018 at 05:57:05PM -0800, Hyun Kwon wrote:
> +static struct drm_driver xlnx_drm_driver = {
> + .driver_features = DRIVER_MODESET | DRIVER_GEM |
> + DRIVER_ATOMIC | DRIVER_PRIME,
> + .lastclose = xlnx_lastclose,
> +
> + .enable_vblank = xlnx_enable_vblank,
> + .disable_vblank = xlnx_disable_vblank,
I thought I've mentioned this already: Please don't use these hooks,
they're deprecated. Instead use the ones in drm_crtc_funcs (that should
also reduce the need for a bit of casting and indirection you have going
on).
-Daniel
--
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v3 2/8] drm: xlnx: Xilinx DRM KMS driver
2018-01-16 1:57 ` [PATCH v3 2/8] drm: xlnx: Xilinx DRM KMS driver Hyun Kwon
[not found] ` <1516067831-11382-2-git-send-email-hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
@ 2018-01-17 8:20 ` Daniel Vetter
2018-01-19 23:33 ` Rob Herring
[not found] ` <20180117082028.GC2759-dv86pmgwkMBes7Z6vYuT8azUEOm+Xw19@public.gmane.org>
1 sibling, 2 replies; 17+ messages in thread
From: Daniel Vetter @ 2018-01-17 8:20 UTC (permalink / raw)
To: Hyun Kwon
Cc: devicetree, Daniel Vetter, Michal Simek, dri-devel, Laurent Pinchart
On Mon, Jan 15, 2018 at 05:57:05PM -0800, Hyun Kwon wrote:
> Xilinx has various platforms for display, where users can create
> using multiple IPs in the programmable FPGA fabric, or where
> some hardened piepline is available on the chip. Furthermore,
> hardened pipeline can also interact with soft logics in FPGA.
>
> The Xilinx DRM KMS is to integrate multiple subdevices and to represent
> the entire pipeline as a single DRM device. The driver includes helpers
> (ex, framebuffer and gem helpers) and glue logics (ex, crtc interface).
>
> Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
> ---
> v3
> - Add Laurent as a maintainer
> - Fix multiple-reference on gem objects
> v2
> - Change the SPDX identifier format
> - Merge patches(crtc, gem, fb) into single one
> v2 of xlnx_drv
> - Rename kms to display in xlnx_drv
> - Replace some xlnx specific fb helper with common helpers in xlnx_drv
> - Don't set the commit tail callback in xlnx_drv
> - Support 'ports' graph binding in xlnx_drv
> v2 of xlnx_fb
> - Remove wrappers in xlnx_fb
> - Replace some functions with drm core helpers in xlnx_fb
> ---
> ---
> MAINTAINERS | 9 +
> drivers/gpu/drm/Kconfig | 2 +
> drivers/gpu/drm/Makefile | 1 +
> drivers/gpu/drm/xlnx/Kconfig | 12 ++
> drivers/gpu/drm/xlnx/Makefile | 2 +
> drivers/gpu/drm/xlnx/xlnx_crtc.c | 203 ++++++++++++++++++
> drivers/gpu/drm/xlnx/xlnx_crtc.h | 78 +++++++
> drivers/gpu/drm/xlnx/xlnx_drv.c | 447 +++++++++++++++++++++++++++++++++++++++
> drivers/gpu/drm/xlnx/xlnx_drv.h | 30 +++
> drivers/gpu/drm/xlnx/xlnx_fb.c | 298 ++++++++++++++++++++++++++
> drivers/gpu/drm/xlnx/xlnx_fb.h | 33 +++
> drivers/gpu/drm/xlnx/xlnx_gem.c | 47 ++++
> drivers/gpu/drm/xlnx/xlnx_gem.h | 26 +++
> 13 files changed, 1188 insertions(+)
> create mode 100644 drivers/gpu/drm/xlnx/Kconfig
> create mode 100644 drivers/gpu/drm/xlnx/Makefile
> create mode 100644 drivers/gpu/drm/xlnx/xlnx_crtc.c
> create mode 100644 drivers/gpu/drm/xlnx/xlnx_crtc.h
> create mode 100644 drivers/gpu/drm/xlnx/xlnx_drv.c
> create mode 100644 drivers/gpu/drm/xlnx/xlnx_drv.h
> create mode 100644 drivers/gpu/drm/xlnx/xlnx_fb.c
> create mode 100644 drivers/gpu/drm/xlnx/xlnx_fb.h
> create mode 100644 drivers/gpu/drm/xlnx/xlnx_gem.c
> create mode 100644 drivers/gpu/drm/xlnx/xlnx_gem.h
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 2811a21..dc84346 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -4682,6 +4682,15 @@ F: drivers/gpu/drm/etnaviv/
> F: include/uapi/drm/etnaviv_drm.h
> F: Documentation/devicetree/bindings/display/etnaviv/
>
> +DRM DRIVERS FOR XILINX
> +M: Hyun Kwon <hyun.kwon@xilinx.com>
> +M: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> +L: dri-devel@lists.freedesktop.org
> +S: Maintained
> +F: drivers/gpu/drm/xlnx/
> +F: Documentation/devicetree/bindings/display/xlnx/
> +T: git git://anongit.freedesktop.org/drm/drm-misc
Ok, I scrolled through the patches again and besides the one nit for the
enable/disable_vblank callback it looks all good. On patches 2 and 4-6:
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are ready for merging. The 2 dt patches need an ack from Rob
Herring. The final 2 patches with the new properties need the usual uapi
work and userspace enabling per
https://dri.freedesktop.org/docs/drm/gpu/drm-uapi.html#open-source-userspace-requirements
Since Laurent is listed as co-maintainer, and Laurent is already drm-misc
committer I think it's indeed best to maintain it in there. Please request
a new account per
https://www.freedesktop.org/wiki/AccountRequests/
and check out quickstart in
https://01.org/linuxgraphics/gfx-docs/maintainer-tools/dim.html#quickstart
For any questions I or Laurent should be able to help out. My expectation
is that once you have the ack from DT maintainers you'll merge patches 1-6
yourself directly.
Thanks, Daniel
> +
> DRM DRIVERS FOR ZTE ZX
> M: Shawn Guo <shawnguo@kernel.org>
> L: dri-devel@lists.freedesktop.org
> diff --git a/drivers/gpu/drm/Kconfig b/drivers/gpu/drm/Kconfig
> index 22ee5a1..f3c71e3 100644
> --- a/drivers/gpu/drm/Kconfig
> +++ b/drivers/gpu/drm/Kconfig
> @@ -282,6 +282,8 @@ source "drivers/gpu/drm/tinydrm/Kconfig"
>
> source "drivers/gpu/drm/pl111/Kconfig"
>
> +source "drivers/gpu/drm/xlnx/Kconfig"
> +
> # Keep legacy drivers last
>
> menuconfig DRM_LEGACY
> diff --git a/drivers/gpu/drm/Makefile b/drivers/gpu/drm/Makefile
> index 92550dd..2f44c77 100644
> --- a/drivers/gpu/drm/Makefile
> +++ b/drivers/gpu/drm/Makefile
> @@ -103,3 +103,4 @@ obj-$(CONFIG_DRM_ZTE) += zte/
> obj-$(CONFIG_DRM_MXSFB) += mxsfb/
> obj-$(CONFIG_DRM_TINYDRM) += tinydrm/
> obj-$(CONFIG_DRM_PL111) += pl111/
> +obj-$(CONFIG_DRM_XLNX) += xlnx/
> diff --git a/drivers/gpu/drm/xlnx/Kconfig b/drivers/gpu/drm/xlnx/Kconfig
> new file mode 100644
> index 0000000..19fd7cd
> --- /dev/null
> +++ b/drivers/gpu/drm/xlnx/Kconfig
> @@ -0,0 +1,12 @@
> +config DRM_XLNX
> + tristate "Xilinx DRM KMS Driver"
> + depends on DRM && OF
> + select DRM_KMS_HELPER
> + select DRM_KMS_CMA_HELPER
> + select DRM_GEM_CMA_HELPER
> + help
> + Xilinx DRM KMS driver. Choose this option if you have
> + a Xilinx SoCs with hardened display pipeline or soft
> + display pipeline using Xilinx IPs in FPGA. This module
> + provides the kernel mode setting functionalities
> + for Xilinx display drivers.
> diff --git a/drivers/gpu/drm/xlnx/Makefile b/drivers/gpu/drm/xlnx/Makefile
> new file mode 100644
> index 0000000..c60a281
> --- /dev/null
> +++ b/drivers/gpu/drm/xlnx/Makefile
> @@ -0,0 +1,2 @@
> +xlnx_drm-objs += xlnx_crtc.o xlnx_drv.o xlnx_fb.o xlnx_gem.o
> +obj-$(CONFIG_DRM_XLNX) += xlnx_drm.o
> diff --git a/drivers/gpu/drm/xlnx/xlnx_crtc.c b/drivers/gpu/drm/xlnx/xlnx_crtc.c
> new file mode 100644
> index 0000000..89beb9e
> --- /dev/null
> +++ b/drivers/gpu/drm/xlnx/xlnx_crtc.c
> @@ -0,0 +1,203 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Xilinx DRM crtc driver
> + *
> + * Copyright (C) 2017 - 2018 Xilinx, Inc.
> + *
> + * Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <drm/drmP.h>
> +
> +#include <linux/list.h>
> +
> +#include "xlnx_crtc.h"
> +#include "xlnx_drv.h"
> +
> +/*
> + * Overview
> + * --------
> + *
> + * The Xilinx CRTC layer is to enable the custom interface to CRTC drivers.
> + * The interface is used by Xilinx DRM driver where it needs CRTC
> + * functionailty. CRTC drivers should attach the desired callbacks
> + * to struct xlnx_crtc and register the xlnx_crtc with correcsponding
> + * drm_device. It's highly recommended CRTC drivers register all callbacks
> + * even though many of them are optional.
> + * The CRTC helper simply walks through the registered CRTC device,
> + * and call the callbacks.
> + */
> +
> +/**
> + * struct xlnx_crtc_helper - Xilinx CRTC helper
> + * @xlnx_crtcs: list of Xilinx CRTC devices
> + * @lock: lock to protect @xlnx_crtcs
> + * @drm: back pointer to DRM core
> + */
> +struct xlnx_crtc_helper {
> + struct list_head xlnx_crtcs;
> + struct mutex lock; /* lock for @xlnx_crtcs */
> + struct drm_device *drm;
> +};
> +
> +#define XLNX_CRTC_MAX_HEIGHT_WIDTH UINT_MAX
> +
> +int xlnx_crtc_helper_enable_vblank(struct xlnx_crtc_helper *helper,
> + unsigned int crtc_id)
> +{
> + struct xlnx_crtc *crtc;
> +
> + list_for_each_entry(crtc, &helper->xlnx_crtcs, list)
> + if (drm_crtc_index(&crtc->crtc) == crtc_id)
> + if (crtc->enable_vblank)
> + return crtc->enable_vblank(crtc);
> + return -ENODEV;
> +}
> +
> +void xlnx_crtc_helper_disable_vblank(struct xlnx_crtc_helper *helper,
> + unsigned int crtc_id)
> +{
> + struct xlnx_crtc *crtc;
> +
> + list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
> + if (drm_crtc_index(&crtc->crtc) == crtc_id) {
> + if (crtc->disable_vblank)
> + crtc->disable_vblank(crtc);
> + return;
> + }
> + }
> +}
> +
> +unsigned int xlnx_crtc_helper_get_align(struct xlnx_crtc_helper *helper)
> +{
> + struct xlnx_crtc *crtc;
> + unsigned int align = 1, tmp;
> +
> + list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
> + if (crtc->get_align) {
> + tmp = crtc->get_align(crtc);
> + align = ALIGN(align, tmp);
> + }
> + }
> +
> + return align;
> +}
> +
> +u64 xlnx_crtc_helper_get_dma_mask(struct xlnx_crtc_helper *helper)
> +{
> + struct xlnx_crtc *crtc;
> + u64 mask = DMA_BIT_MASK(sizeof(dma_addr_t) * 8), tmp;
> +
> + list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
> + if (crtc->get_dma_mask) {
> + tmp = crtc->get_dma_mask(crtc);
> + mask = min(mask, tmp);
> + }
> + }
> +
> + return mask;
> +}
> +
> +int xlnx_crtc_helper_get_max_width(struct xlnx_crtc_helper *helper)
> +{
> + struct xlnx_crtc *crtc;
> + unsigned int width = XLNX_CRTC_MAX_HEIGHT_WIDTH, tmp;
> +
> + list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
> + if (crtc->get_max_width) {
> + tmp = crtc->get_max_width(crtc);
> + width = min(width, tmp);
> + }
> + }
> +
> + return width;
> +}
> +
> +int xlnx_crtc_helper_get_max_height(struct xlnx_crtc_helper *helper)
> +{
> + struct xlnx_crtc *crtc;
> + unsigned int height = XLNX_CRTC_MAX_HEIGHT_WIDTH, tmp;
> +
> + list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
> + if (crtc->get_max_height) {
> + tmp = crtc->get_max_height(crtc);
> + height = min(height, tmp);
> + }
> + }
> +
> + return height;
> +}
> +
> +uint32_t xlnx_crtc_helper_get_format(struct xlnx_crtc_helper *helper)
> +{
> + struct xlnx_crtc *crtc;
> + u32 format = 0, tmp;
> +
> + list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
> + if (crtc->get_format) {
> + tmp = crtc->get_format(crtc);
> + if (format && format != tmp)
> + return 0;
> + format = tmp;
> + }
> + }
> +
> + return format;
> +}
> +
> +struct xlnx_crtc_helper *xlnx_crtc_helper_init(struct drm_device *drm)
> +{
> + struct xlnx_crtc_helper *helper;
> +
> + helper = devm_kzalloc(drm->dev, sizeof(*helper), GFP_KERNEL);
> + if (!helper)
> + return ERR_PTR(-ENOMEM);
> +
> + INIT_LIST_HEAD(&helper->xlnx_crtcs);
> + mutex_init(&helper->lock);
> + helper->drm = drm;
> +
> + return helper;
> +}
> +
> +void xlnx_crtc_helper_fini(struct drm_device *drm,
> + struct xlnx_crtc_helper *helper)
> +{
> + if (WARN_ON(helper->drm != drm))
> + return;
> +
> + if (WARN_ON(!list_empty(&helper->xlnx_crtcs)))
> + return;
> +
> + mutex_destroy(&helper->lock);
> + devm_kfree(drm->dev, helper);
> +}
> +
> +void xlnx_crtc_register(struct drm_device *drm, struct xlnx_crtc *crtc)
> +{
> + struct xlnx_crtc_helper *helper = xlnx_get_crtc_helper(drm);
> +
> + mutex_lock(&helper->lock);
> + list_add_tail(&crtc->list, &helper->xlnx_crtcs);
> + mutex_unlock(&helper->lock);
> +}
> +EXPORT_SYMBOL_GPL(xlnx_crtc_register);
> +
> +void xlnx_crtc_unregister(struct drm_device *drm, struct xlnx_crtc *crtc)
> +{
> + struct xlnx_crtc_helper *helper = xlnx_get_crtc_helper(drm);
> +
> + mutex_lock(&helper->lock);
> + list_del(&crtc->list);
> + mutex_unlock(&helper->lock);
> +}
> +EXPORT_SYMBOL_GPL(xlnx_crtc_unregister);
> diff --git a/drivers/gpu/drm/xlnx/xlnx_crtc.h b/drivers/gpu/drm/xlnx/xlnx_crtc.h
> new file mode 100644
> index 0000000..1498e10
> --- /dev/null
> +++ b/drivers/gpu/drm/xlnx/xlnx_crtc.h
> @@ -0,0 +1,78 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Xilinx DRM crtc header
> + *
> + * Copyright (C) 2017 - 2018 Xilinx, Inc.
> + *
> + * Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#ifndef _XLNX_CRTC_H_
> +#define _XLNX_CRTC_H_
> +
> +/**
> + * struct xlnx_crtc - Xilinx CRTC device
> + * @crtc: DRM CRTC device
> + * @list: list node for Xilinx CRTC device list
> + * @enable_vblank: Enable vblank
> + * @disable_vblank: Disable vblank
> + * @get_align: Get the alignment requirement of CRTC device
> + * @get_dma_mask: Get the dma mask of CRTC device
> + * @get_max_width: Get the maximum supported width
> + * @get_max_height: Get the maximum supported height
> + * @get_format: Get the current format of CRTC device
> + */
> +struct xlnx_crtc {
> + struct drm_crtc crtc;
> + struct list_head list;
> + int (*enable_vblank)(struct xlnx_crtc *crtc);
> + void (*disable_vblank)(struct xlnx_crtc *crtc);
> + unsigned int (*get_align)(struct xlnx_crtc *crtc);
> + u64 (*get_dma_mask)(struct xlnx_crtc *crtc);
> + int (*get_max_width)(struct xlnx_crtc *crtc);
> + int (*get_max_height)(struct xlnx_crtc *crtc);
> + uint32_t (*get_format)(struct xlnx_crtc *crtc);
> +};
> +
> +/*
> + * Helper functions: used within Xlnx DRM
> + */
> +
> +struct xlnx_crtc_helper;
> +
> +int xlnx_crtc_helper_enable_vblank(struct xlnx_crtc_helper *helper,
> + unsigned int crtc_id);
> +void xlnx_crtc_helper_disable_vblank(struct xlnx_crtc_helper *helper,
> + unsigned int crtc_id);
> +unsigned int xlnx_crtc_helper_get_align(struct xlnx_crtc_helper *helper);
> +u64 xlnx_crtc_helper_get_dma_mask(struct xlnx_crtc_helper *helper);
> +int xlnx_crtc_helper_get_max_width(struct xlnx_crtc_helper *helper);
> +int xlnx_crtc_helper_get_max_height(struct xlnx_crtc_helper *helper);
> +uint32_t xlnx_crtc_helper_get_format(struct xlnx_crtc_helper *helper);
> +
> +struct xlnx_crtc_helper *xlnx_crtc_helper_init(struct drm_device *drm);
> +void xlnx_crtc_helper_fini(struct drm_device *drm,
> + struct xlnx_crtc_helper *helper);
> +
> +/*
> + * CRTC registration: used by other sub-driver modules
> + */
> +
> +static inline struct xlnx_crtc *to_xlnx_crtc(struct drm_crtc *crtc)
> +{
> + return container_of(crtc, struct xlnx_crtc, crtc);
> +}
> +
> +void xlnx_crtc_register(struct drm_device *drm, struct xlnx_crtc *crtc);
> +void xlnx_crtc_unregister(struct drm_device *drm, struct xlnx_crtc *crtc);
> +
> +#endif /* _XLNX_CRTC_H_ */
> diff --git a/drivers/gpu/drm/xlnx/xlnx_drv.c b/drivers/gpu/drm/xlnx/xlnx_drv.c
> new file mode 100644
> index 0000000..a350492
> --- /dev/null
> +++ b/drivers/gpu/drm/xlnx/xlnx_drv.c
> @@ -0,0 +1,447 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Xilinx DRM KMS Driver
> + *
> + * Copyright (C) 2013 - 2018 Xilinx, Inc.
> + *
> + * Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <drm/drmP.h>
> +#include <drm/drm_atomic.h>
> +#include <drm/drm_atomic_helper.h>
> +#include <drm/drm_crtc_helper.h>
> +#include <drm/drm_fb_helper.h>
> +#include <drm/drm_gem_cma_helper.h>
> +#include <drm/drm_of.h>
> +
> +#include <linux/component.h>
> +#include <linux/device.h>
> +#include <linux/dma-buf.h>
> +#include <linux/module.h>
> +#include <linux/of_graph.h>
> +#include <linux/platform_device.h>
> +#include <linux/reservation.h>
> +
> +#include "xlnx_crtc.h"
> +#include "xlnx_fb.h"
> +#include "xlnx_gem.h"
> +
> +#define DRIVER_NAME "xlnx"
> +#define DRIVER_DESC "Xilinx DRM KMS Driver"
> +#define DRIVER_DATE "20130509"
> +#define DRIVER_MAJOR 1
> +#define DRIVER_MINOR 0
> +
> +static uint xlnx_fbdev_vres = 2;
> +module_param_named(fbdev_vres, xlnx_fbdev_vres, uint, 0444);
> +MODULE_PARM_DESC(fbdev_vres,
> + "fbdev virtual resolution multiplier for fb (default: 2)");
> +
> +/**
> + * struct xlnx_drm - Xilinx DRM private data
> + * @drm: DRM core
> + * @crtc: Xilinx DRM CRTC helper
> + * @fb: DRM fb helper
> + * @pdev: platform device
> + * @suspend_state: atomic state for suspend / resume
> + */
> +struct xlnx_drm {
> + struct drm_device *drm;
> + struct xlnx_crtc_helper *crtc;
> + struct drm_fb_helper *fb;
> + struct platform_device *pdev;
> + struct drm_atomic_state *suspend_state;
> +};
> +
> +/**
> + * xlnx_get_crtc_helper - Return the crtc helper instance
> + * @drm: DRM device
> + *
> + * Return: the crtc helper instance
> + */
> +struct xlnx_crtc_helper *xlnx_get_crtc_helper(struct drm_device *drm)
> +{
> + struct xlnx_drm *xlnx_drm = drm->dev_private;
> +
> + return xlnx_drm->crtc;
> +}
> +
> +/**
> + * xlnx_get_align - Return the align requirement through CRTC helper
> + * @drm: DRM device
> + *
> + * Return: the alignment requirement
> + */
> +unsigned int xlnx_get_align(struct drm_device *drm)
> +{
> + struct xlnx_drm *xlnx_drm = drm->dev_private;
> +
> + return xlnx_crtc_helper_get_align(xlnx_drm->crtc);
> +}
> +
> +/**
> + * xlnx_get_format - Return the current format of CRTC
> + * @drm: DRM device
> + *
> + * Return: the current CRTC format
> + */
> +uint32_t xlnx_get_format(struct drm_device *drm)
> +{
> + struct xlnx_drm *xlnx_drm = drm->dev_private;
> +
> + return xlnx_crtc_helper_get_format(xlnx_drm->crtc);
> +}
> +
> +static void xlnx_output_poll_changed(struct drm_device *drm)
> +{
> + struct xlnx_drm *xlnx_drm = drm->dev_private;
> +
> + if (xlnx_drm->fb)
> + drm_fb_helper_hotplug_event(xlnx_drm->fb);
> +}
> +
> +static const struct drm_mode_config_funcs xlnx_mode_config_funcs = {
> + .fb_create = xlnx_fb_create,
> + .output_poll_changed = xlnx_output_poll_changed,
> + .atomic_check = drm_atomic_helper_check,
> + .atomic_commit = drm_atomic_helper_commit,
> +};
> +
> +static int xlnx_enable_vblank(struct drm_device *drm, unsigned int crtc)
> +{
> + struct xlnx_drm *xlnx_drm = drm->dev_private;
> +
> + return xlnx_crtc_helper_enable_vblank(xlnx_drm->crtc, crtc);
> +}
> +
> +static void xlnx_disable_vblank(struct drm_device *drm, unsigned int crtc)
> +{
> + struct xlnx_drm *xlnx_drm = drm->dev_private;
> +
> + xlnx_crtc_helper_disable_vblank(xlnx_drm->crtc, crtc);
> +}
> +
> +static void xlnx_mode_config_init(struct drm_device *drm)
> +{
> + struct xlnx_drm *xlnx_drm = drm->dev_private;
> + struct xlnx_crtc_helper *crtc = xlnx_drm->crtc;
> +
> + drm->mode_config.min_width = 0;
> + drm->mode_config.min_height = 0;
> + drm->mode_config.max_width = xlnx_crtc_helper_get_max_width(crtc);
> + drm->mode_config.max_height = xlnx_crtc_helper_get_max_height(crtc);
> +}
> +
> +static void xlnx_lastclose(struct drm_device *drm)
> +{
> + struct xlnx_drm *xlnx_drm = drm->dev_private;
> +
> + if (xlnx_drm->fb)
> + drm_fb_helper_restore_fbdev_mode_unlocked(xlnx_drm->fb);
> +}
> +
> +static const struct file_operations xlnx_fops = {
> + .owner = THIS_MODULE,
> + .open = drm_open,
> + .release = drm_release,
> + .unlocked_ioctl = drm_ioctl,
> + .mmap = drm_gem_cma_mmap,
> + .poll = drm_poll,
> + .read = drm_read,
> +#ifdef CONFIG_COMPAT
> + .compat_ioctl = drm_compat_ioctl,
> +#endif
> + .llseek = noop_llseek,
> +};
> +
> +static struct drm_driver xlnx_drm_driver = {
> + .driver_features = DRIVER_MODESET | DRIVER_GEM |
> + DRIVER_ATOMIC | DRIVER_PRIME,
> + .lastclose = xlnx_lastclose,
> +
> + .enable_vblank = xlnx_enable_vblank,
> + .disable_vblank = xlnx_disable_vblank,
> +
> + .prime_handle_to_fd = drm_gem_prime_handle_to_fd,
> + .prime_fd_to_handle = drm_gem_prime_fd_to_handle,
> + .gem_prime_export = drm_gem_prime_export,
> + .gem_prime_import = drm_gem_prime_import,
> + .gem_prime_get_sg_table = drm_gem_cma_prime_get_sg_table,
> + .gem_prime_import_sg_table = drm_gem_cma_prime_import_sg_table,
> + .gem_prime_vmap = drm_gem_cma_prime_vmap,
> + .gem_prime_vunmap = drm_gem_cma_prime_vunmap,
> + .gem_prime_mmap = drm_gem_cma_prime_mmap,
> + .gem_free_object = drm_gem_cma_free_object,
> + .gem_vm_ops = &drm_gem_cma_vm_ops,
> + .dumb_create = xlnx_gem_cma_dumb_create,
> + .dumb_destroy = drm_gem_dumb_destroy,
> +
> + .fops = &xlnx_fops,
> +
> + .name = DRIVER_NAME,
> + .desc = DRIVER_DESC,
> + .date = DRIVER_DATE,
> + .major = DRIVER_MAJOR,
> + .minor = DRIVER_MINOR,
> +};
> +
> +static int xlnx_bind(struct device *dev)
> +{
> + struct xlnx_drm *xlnx_drm;
> + struct drm_device *drm;
> + const struct drm_format_info *info;
> + struct platform_device *pdev = to_platform_device(dev);
> + int ret;
> + u32 format;
> +
> + drm = drm_dev_alloc(&xlnx_drm_driver, &pdev->dev);
> + if (IS_ERR(drm))
> + return PTR_ERR(drm);
> +
> + xlnx_drm = devm_kzalloc(drm->dev, sizeof(*xlnx_drm), GFP_KERNEL);
> + if (!xlnx_drm) {
> + ret = -ENOMEM;
> + goto err_drm;
> + }
> +
> + drm_mode_config_init(drm);
> + drm->mode_config.funcs = &xlnx_mode_config_funcs;
> +
> + ret = drm_vblank_init(drm, 1);
> + if (ret) {
> + dev_err(&pdev->dev, "failed to initialize vblank\n");
> + goto err_xlnx_drm;
> + }
> +
> + drm->irq_enabled = 1;
> + drm->dev_private = xlnx_drm;
> + xlnx_drm->drm = drm;
> + drm_kms_helper_poll_init(drm);
> + platform_set_drvdata(pdev, xlnx_drm);
> +
> + xlnx_drm->crtc = xlnx_crtc_helper_init(drm);
> + if (IS_ERR(xlnx_drm->crtc)) {
> + ret = PTR_ERR(xlnx_drm->crtc);
> + goto err_xlnx_drm;
> + }
> +
> + ret = component_bind_all(drm->dev, drm);
> + if (ret)
> + goto err_crtc;
> +
> + xlnx_mode_config_init(drm);
> + drm_mode_config_reset(drm);
> + dma_set_mask(drm->dev, xlnx_crtc_helper_get_dma_mask(xlnx_drm->crtc));
> +
> + format = xlnx_crtc_helper_get_format(xlnx_drm->crtc);
> + info = drm_format_info(format);
> + if (info && info->depth && info->cpp[0]) {
> + unsigned int align;
> +
> + align = xlnx_crtc_helper_get_align(xlnx_drm->crtc);
> + xlnx_drm->fb = xlnx_fb_init(drm, info->cpp[0] * 8, 1, align,
> + xlnx_fbdev_vres);
> + if (IS_ERR(xlnx_drm->fb)) {
> + dev_err(&pdev->dev,
> + "failed to initialize drm fb\n");
> + xlnx_drm->fb = NULL;
> + }
> + } else {
> + /* fbdev emulation is optional */
> + dev_info(&pdev->dev, "fbdev is not initialized\n");
> + }
> +
> + ret = drm_dev_register(drm, 0);
> + if (ret < 0)
> + goto err_fb;
> +
> + return 0;
> +
> +err_fb:
> + if (xlnx_drm->fb)
> + xlnx_fb_fini(xlnx_drm->fb);
> + component_unbind_all(drm->dev, drm);
> +err_crtc:
> + xlnx_crtc_helper_fini(drm, xlnx_drm->crtc);
> +err_xlnx_drm:
> + drm_mode_config_cleanup(drm);
> +err_drm:
> + drm_dev_unref(drm);
> + return ret;
> +}
> +
> +static void xlnx_unbind(struct device *dev)
> +{
> + struct xlnx_drm *xlnx_drm = dev_get_drvdata(dev);
> + struct drm_device *drm = xlnx_drm->drm;
> +
> + drm_dev_unregister(drm);
> + if (xlnx_drm->fb)
> + xlnx_fb_fini(xlnx_drm->fb);
> + component_unbind_all(drm->dev, drm);
> + xlnx_crtc_helper_fini(drm, xlnx_drm->crtc);
> + drm_kms_helper_poll_fini(drm);
> + drm_mode_config_cleanup(drm);
> + drm_dev_unref(drm);
> +}
> +
> +static const struct component_master_ops xlnx_master_ops = {
> + .bind = xlnx_bind,
> + .unbind = xlnx_unbind,
> +};
> +
> +static int xlnx_of_component_probe(struct device *dev,
> + int (*compare_of)(struct device *, void *),
> + const struct component_master_ops *m_ops)
> +{
> + struct device_node *ep, *port, *remote, *parent;
> + struct component_match *match = NULL;
> + int i;
> +
> + if (!dev->of_node)
> + return -EINVAL;
> +
> + for (i = 0; ; i++) {
> + port = of_parse_phandle(dev->of_node, "ports", i);
> + if (!port)
> + break;
> +
> + parent = of_graph_get_port_parent(port);
> + if (!of_device_is_available(parent)) {
> + of_node_put(port);
> + continue;
> + }
> +
> + component_match_add(dev, &match, compare_of, parent);
> + of_node_put(parent);
> + of_node_put(port);
> + }
> +
> + if (i == 0) {
> + dev_err(dev, "missing 'ports' property\n");
> + return -ENODEV;
> + }
> +
> + if (!match) {
> + dev_err(dev, "no available port\n");
> + return -ENODEV;
> + }
> +
> + for (i = 0; ; i++) {
> + port = of_parse_phandle(dev->of_node, "ports", i);
> + if (!port)
> + break;
> +
> + parent = of_graph_get_port_parent(port);
> + if (!of_device_is_available(parent)) {
> + of_node_put(port);
> + continue;
> + }
> +
> + for_each_child_of_node(port, ep) {
> + remote = of_graph_get_remote_port_parent(ep);
> + if (!remote || !of_device_is_available(remote)) {
> + of_node_put(remote);
> + continue;
> + } else if (!of_device_is_available(remote->parent)) {
> + dev_warn(dev, "parent dev of %s unavailable\n",
> + remote->full_name);
> + of_node_put(remote);
> + continue;
> + }
> + component_match_add(dev, &match, compare_of, remote);
> + of_node_put(remote);
> + }
> + of_node_put(port);
> + }
> +
> + return component_master_add_with_match(dev, m_ops, match);
> +}
> +
> +static int xlnx_compare_of(struct device *dev, void *data)
> +{
> + return dev->of_node == data;
> +}
> +
> +static int xlnx_platform_probe(struct platform_device *pdev)
> +{
> + return xlnx_of_component_probe(&pdev->dev, xlnx_compare_of,
> + &xlnx_master_ops);
> +}
> +
> +static int xlnx_platform_remove(struct platform_device *pdev)
> +{
> + component_master_del(&pdev->dev, &xlnx_master_ops);
> + return 0;
> +}
> +
> +static void xlnx_platform_shutdown(struct platform_device *pdev)
> +{
> + struct xlnx_drm *xlnx_drm = platform_get_drvdata(pdev);
> +
> + drm_put_dev(xlnx_drm->drm);
> +}
> +
> +static int __maybe_unused xlnx_pm_suspend(struct device *dev)
> +{
> + struct xlnx_drm *xlnx_drm = dev_get_drvdata(dev);
> + struct drm_device *drm = xlnx_drm->drm;
> +
> + drm_kms_helper_poll_disable(drm);
> +
> + xlnx_drm->suspend_state = drm_atomic_helper_suspend(drm);
> + if (IS_ERR(xlnx_drm->suspend_state)) {
> + drm_kms_helper_poll_enable(drm);
> + return PTR_ERR(xlnx_drm->suspend_state);
> + }
> +
> + return 0;
> +}
> +
> +static int __maybe_unused xlnx_pm_resume(struct device *dev)
> +{
> + struct xlnx_drm *xlnx_drm = dev_get_drvdata(dev);
> + struct drm_device *drm = xlnx_drm->drm;
> +
> + drm_atomic_helper_resume(drm, xlnx_drm->suspend_state);
> + drm_kms_helper_poll_enable(drm);
> +
> + return 0;
> +}
> +
> +static const struct dev_pm_ops xlnx_pm_ops = {
> + SET_SYSTEM_SLEEP_PM_OPS(xlnx_pm_suspend, xlnx_pm_resume)
> +};
> +
> +static const struct of_device_id xlnx_of_match[] = {
> + { .compatible = "xlnx,display", },
> + { /* end of table */ },
> +};
> +MODULE_DEVICE_TABLE(of, xlnx_of_match);
> +
> +static struct platform_driver xlnx_driver = {
> + .probe = xlnx_platform_probe,
> + .remove = xlnx_platform_remove,
> + .shutdown = xlnx_platform_shutdown,
> + .driver = {
> + .name = "xlnx-drm",
> + .pm = &xlnx_pm_ops,
> + .of_match_table = xlnx_of_match,
> + },
> +};
> +
> +module_platform_driver(xlnx_driver);
> +
> +MODULE_AUTHOR("Xilinx, Inc.");
> +MODULE_DESCRIPTION("Xilinx DRM KMS Driver");
> +MODULE_LICENSE("GPL v2");
> diff --git a/drivers/gpu/drm/xlnx/xlnx_drv.h b/drivers/gpu/drm/xlnx/xlnx_drv.h
> new file mode 100644
> index 0000000..8c320fd
> --- /dev/null
> +++ b/drivers/gpu/drm/xlnx/xlnx_drv.h
> @@ -0,0 +1,30 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Xilinx DRM KMS Header for Xilinx
> + *
> + * Copyright (C) 2013 - 2018 Xilinx, Inc.
> + *
> + * Author: Hyun Woo Kwon <hyunk@xilinx.com>
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#ifndef _XLNX_DRV_H_
> +#define _XLNX_DRV_H_
> +
> +struct drm_device;
> +struct xlnx_crtc_helper;
> +
> +uint32_t xlnx_get_format(struct drm_device *drm);
> +unsigned int xlnx_get_align(struct drm_device *drm);
> +struct xlnx_crtc_helper *xlnx_get_crtc_helper(struct drm_device *drm);
> +struct xlnx_bridge_helper *xlnx_get_bridge_helper(struct drm_device *drm);
> +
> +#endif /* _XLNX_DRV_H_ */
> diff --git a/drivers/gpu/drm/xlnx/xlnx_fb.c b/drivers/gpu/drm/xlnx/xlnx_fb.c
> new file mode 100644
> index 0000000..e72087d
> --- /dev/null
> +++ b/drivers/gpu/drm/xlnx/xlnx_fb.c
> @@ -0,0 +1,298 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Xilinx DRM KMS Framebuffer helper
> + *
> + * Copyright (C) 2015 - 2018 Xilinx, Inc.
> + *
> + * Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
> + *
> + * Based on drm_fb_cma_helper.c
> + *
> + * Copyright (C) 2012 Analog Device Inc.
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <drm/drmP.h>
> +#include <drm/drm_crtc.h>
> +#include <drm/drm_crtc_helper.h>
> +#include <drm/drm_fb_helper.h>
> +#include <drm/drm_gem_cma_helper.h>
> +#include <drm/drm_gem_framebuffer_helper.h>
> +
> +#include "xlnx_drv.h"
> +#include "xlnx_fb.h"
> +
> +#define XLNX_MAX_PLANES 4
> +
> +struct xlnx_fbdev {
> + struct drm_fb_helper fb_helper;
> + struct drm_framebuffer *fb;
> + unsigned int align;
> + unsigned int vres_mult;
> +};
> +
> +static inline struct xlnx_fbdev *to_fbdev(struct drm_fb_helper *fb_helper)
> +{
> + return container_of(fb_helper, struct xlnx_fbdev, fb_helper);
> +}
> +
> +static struct drm_framebuffer_funcs xlnx_fb_funcs = {
> + .destroy = drm_gem_fb_destroy,
> + .create_handle = drm_gem_fb_create_handle,
> +};
> +
> +static int
> +xlnx_fb_ioctl(struct fb_info *info, unsigned int cmd, unsigned long arg)
> +{
> + struct drm_fb_helper *fb_helper = info->par;
> + unsigned int i;
> + int ret = 0;
> +
> + switch (cmd) {
> + case FBIO_WAITFORVSYNC:
> + for (i = 0; i < fb_helper->crtc_count; i++) {
> + struct drm_mode_set *mode_set;
> + struct drm_crtc *crtc;
> +
> + mode_set = &fb_helper->crtc_info[i].mode_set;
> + crtc = mode_set->crtc;
> + ret = drm_crtc_vblank_get(crtc);
> + if (!ret) {
> + drm_crtc_wait_one_vblank(crtc);
> + drm_crtc_vblank_put(crtc);
> + }
> + }
> + return ret;
> + default:
> + return -ENOTTY;
> + }
> +
> + return 0;
> +}
> +
> +static struct fb_ops xlnx_fbdev_ops = {
> + .owner = THIS_MODULE,
> + .fb_fillrect = sys_fillrect,
> + .fb_copyarea = sys_copyarea,
> + .fb_imageblit = sys_imageblit,
> + .fb_check_var = drm_fb_helper_check_var,
> + .fb_set_par = drm_fb_helper_set_par,
> + .fb_blank = drm_fb_helper_blank,
> + .fb_pan_display = drm_fb_helper_pan_display,
> + .fb_setcmap = drm_fb_helper_setcmap,
> + .fb_ioctl = xlnx_fb_ioctl,
> +};
> +
> +/**
> + * xlnx_fbdev_create - Create the fbdev with a framebuffer
> + * @fb_helper: fb helper structure
> + * @size: framebuffer size info
> + *
> + * This function is based on drm_fbdev_cma_create().
> + *
> + * Return: 0 if successful, or the error code.
> + */
> +static int xlnx_fbdev_create(struct drm_fb_helper *fb_helper,
> + struct drm_fb_helper_surface_size *size)
> +{
> + struct xlnx_fbdev *fbdev = to_fbdev(fb_helper);
> + struct drm_device *drm = fb_helper->dev;
> + struct drm_gem_cma_object *obj;
> + struct drm_framebuffer *fb;
> + unsigned int bytes_per_pixel;
> + unsigned long offset;
> + struct fb_info *fbi;
> + size_t bytes;
> + int ret;
> +
> + dev_dbg(drm->dev, "surface width(%d), height(%d) and bpp(%d)\n",
> + size->surface_width, size->surface_height, size->surface_bpp);
> +
> + size->surface_height *= fbdev->vres_mult;
> + bytes_per_pixel = DIV_ROUND_UP(size->surface_bpp, 8);
> + bytes = ALIGN(size->surface_width * bytes_per_pixel, fbdev->align);
> + bytes *= size->surface_height;
> +
> + obj = drm_gem_cma_create(drm, bytes);
> + if (IS_ERR(obj))
> + return PTR_ERR(obj);
> +
> + fbi = framebuffer_alloc(0, drm->dev);
> + if (!fbi) {
> + dev_err(drm->dev, "Failed to allocate framebuffer info.\n");
> + ret = -ENOMEM;
> + goto err_drm_gem_cma_free_object;
> + }
> +
> + fbdev->fb = drm_gem_fbdev_fb_create(drm, size, fbdev->align, &obj->base,
> + &xlnx_fb_funcs);
> + if (IS_ERR(fbdev->fb)) {
> + dev_err(drm->dev, "Failed to allocate DRM framebuffer.\n");
> + ret = PTR_ERR(fbdev->fb);
> + goto err_framebuffer_release;
> + }
> +
> + fb = fbdev->fb;
> + fb_helper->fb = fb;
> + fb_helper->fbdev = fbi;
> + fbi->par = fb_helper;
> + fbi->flags = FBINFO_FLAG_DEFAULT;
> + fbi->fbops = &xlnx_fbdev_ops;
> +
> + ret = fb_alloc_cmap(&fbi->cmap, 256, 0);
> + if (ret) {
> + dev_err(drm->dev, "Failed to allocate color map.\n");
> + goto err_fb_destroy;
> + }
> +
> + drm_fb_helper_fill_fix(fbi, fb->pitches[0], fb->format->depth);
> + drm_fb_helper_fill_var(fbi, fb_helper, fb->width, fb->height);
> + fbi->var.yres = fb->height / fbdev->vres_mult;
> +
> + offset = fbi->var.xoffset * bytes_per_pixel;
> + offset += fbi->var.yoffset * fb->pitches[0];
> +
> + drm->mode_config.fb_base = (resource_size_t)obj->paddr;
> + fbi->screen_base = (char __iomem *)(obj->vaddr + offset);
> + fbi->fix.smem_start = (unsigned long)(obj->paddr + offset);
> + fbi->screen_size = bytes;
> + fbi->fix.smem_len = bytes;
> +
> + return 0;
> +
> +err_fb_destroy:
> + drm_framebuffer_unregister_private(fb);
> + drm_gem_fb_destroy(fb);
> +err_framebuffer_release:
> + framebuffer_release(fbi);
> +err_drm_gem_cma_free_object:
> + drm_gem_cma_free_object(&obj->base);
> + return ret;
> +}
> +
> +static struct drm_fb_helper_funcs xlnx_fb_helper_funcs = {
> + .fb_probe = xlnx_fbdev_create,
> +};
> +
> +/**
> + * xlnx_fb_init - Allocate and initializes the Xilinx framebuffer
> + * @drm: DRM device
> + * @preferred_bpp: preferred bits per pixel for the device
> + * @max_conn_count: maximum number of connectors
> + * @align: alignment value for pitch
> + * @vres_mult: multiplier for virtual resolution
> + *
> + * This function is based on drm_fbdev_cma_init().
> + *
> + * Return: a newly allocated drm_fb_helper struct or a ERR_PTR.
> + */
> +struct drm_fb_helper *
> +xlnx_fb_init(struct drm_device *drm, int preferred_bpp,
> + unsigned int max_conn_count, unsigned int align,
> + unsigned int vres_mult)
> +{
> + struct xlnx_fbdev *fbdev;
> + struct drm_fb_helper *fb_helper;
> + int ret;
> +
> + fbdev = kzalloc(sizeof(*fbdev), GFP_KERNEL);
> + if (!fbdev)
> + return ERR_PTR(-ENOMEM);
> +
> + fbdev->vres_mult = vres_mult;
> + fbdev->align = align;
> + fb_helper = &fbdev->fb_helper;
> + drm_fb_helper_prepare(drm, fb_helper, &xlnx_fb_helper_funcs);
> +
> + ret = drm_fb_helper_init(drm, fb_helper, max_conn_count);
> + if (ret < 0) {
> + dev_err(drm->dev, "Failed to initialize drm fb helper.\n");
> + goto err_free;
> + }
> +
> + ret = drm_fb_helper_single_add_all_connectors(fb_helper);
> + if (ret < 0) {
> + dev_err(drm->dev, "Failed to add connectors.\n");
> + goto err_drm_fb_helper_fini;
> + }
> +
> + ret = drm_fb_helper_initial_config(fb_helper, preferred_bpp);
> + if (ret < 0) {
> + dev_err(drm->dev, "Failed to set initial hw configuration.\n");
> + goto err_drm_fb_helper_fini;
> + }
> +
> + return fb_helper;
> +
> +err_drm_fb_helper_fini:
> + drm_fb_helper_fini(fb_helper);
> +err_free:
> + kfree(fbdev);
> + return ERR_PTR(ret);
> +}
> +
> +/**
> + * xlnx_fbdev_defio_fini - Free the defio fb
> + * @fbi: fb_info struct
> + *
> + * This function is based on drm_fbdev_cma_defio_fini().
> + */
> +static void xlnx_fbdev_defio_fini(struct fb_info *fbi)
> +{
> + if (!fbi->fbdefio)
> + return;
> +
> + fb_deferred_io_cleanup(fbi);
> + kfree(fbi->fbdefio);
> + kfree(fbi->fbops);
> +}
> +
> +/**
> + * xlnx_fbdev_fini - Free the Xilinx framebuffer
> + * @fb_helper: drm_fb_helper struct
> + *
> + * This function is based on drm_fbdev_cma_fini().
> + */
> +void xlnx_fb_fini(struct drm_fb_helper *fb_helper)
> +{
> + struct xlnx_fbdev *fbdev = to_fbdev(fb_helper);
> +
> + drm_fb_helper_unregister_fbi(&fbdev->fb_helper);
> + if (fbdev->fb_helper.fbdev)
> + xlnx_fbdev_defio_fini(fbdev->fb_helper.fbdev);
> +
> + if (fbdev->fb_helper.fb)
> + drm_framebuffer_remove(fbdev->fb_helper.fb);
> +
> + drm_fb_helper_fini(&fbdev->fb_helper);
> + kfree(fbdev);
> +}
> +
> +/**
> + * xlnx_fb_create - (struct drm_mode_config_funcs *)->fb_create callback
> + * @drm: DRM device
> + * @file_priv: drm file private data
> + * @mode_cmd: mode command for fb creation
> + *
> + * This functions creates a drm_framebuffer with xlnx_fb_funcs for given mode
> + * @mode_cmd. This functions is intended to be used for the fb_create callback
> + * function of drm_mode_config_funcs.
> + *
> + * Return: a drm_framebuffer object if successful, or
> + * ERR_PTR from drm_gem_fb_create_with_funcs().
> + */
> +struct drm_framebuffer *
> +xlnx_fb_create(struct drm_device *drm, struct drm_file *file_priv,
> + const struct drm_mode_fb_cmd2 *mode_cmd)
> +{
> + return drm_gem_fb_create_with_funcs(drm, file_priv, mode_cmd,
> + &xlnx_fb_funcs);
> +}
> diff --git a/drivers/gpu/drm/xlnx/xlnx_fb.h b/drivers/gpu/drm/xlnx/xlnx_fb.h
> new file mode 100644
> index 0000000..6efc985
> --- /dev/null
> +++ b/drivers/gpu/drm/xlnx/xlnx_fb.h
> @@ -0,0 +1,33 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Xilinx DRM KMS Framebuffer helper header
> + *
> + * Copyright (C) 2015 - 2018 Xilinx, Inc.
> + *
> + * Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#ifndef _XLNX_FB_H_
> +#define _XLNX_FB_H_
> +
> +struct drm_fb_helper;
> +
> +struct drm_framebuffer *
> +xlnx_fb_create(struct drm_device *drm, struct drm_file *file_priv,
> + const struct drm_mode_fb_cmd2 *mode_cmd);
> +struct drm_fb_helper *
> +xlnx_fb_init(struct drm_device *drm, int preferred_bpp,
> + unsigned int max_conn_count, unsigned int align,
> + unsigned int vres_mult);
> +void xlnx_fb_fini(struct drm_fb_helper *fb_helper);
> +
> +#endif /* _XLNX_FB_H_ */
> diff --git a/drivers/gpu/drm/xlnx/xlnx_gem.c b/drivers/gpu/drm/xlnx/xlnx_gem.c
> new file mode 100644
> index 0000000..4a5d533
> --- /dev/null
> +++ b/drivers/gpu/drm/xlnx/xlnx_gem.c
> @@ -0,0 +1,47 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Xilinx DRM KMS GEM helper
> + *
> + * Copyright (C) 2015 - 2018 Xilinx, Inc.
> + *
> + * Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <drm/drmP.h>
> +#include <drm/drm_gem_cma_helper.h>
> +
> +#include "xlnx_drv.h"
> +#include "xlnx_gem.h"
> +
> +/*
> + * xlnx_gem_cma_dumb_create - (struct drm_driver)->dumb_create callback
> + * @file_priv: drm_file object
> + * @drm: DRM object
> + * @args: info for dumb scanout buffer creation
> + *
> + * This function is for dumb_create callback of drm_driver struct. Simply
> + * it wraps around drm_gem_cma_dumb_create() and sets the pitch value
> + * by retrieving the value from the device.
> + *
> + * Return: The return value from drm_gem_cma_dumb_create()
> + */
> +int xlnx_gem_cma_dumb_create(struct drm_file *file_priv, struct drm_device *drm,
> + struct drm_mode_create_dumb *args)
> +{
> + int pitch = DIV_ROUND_UP(args->width * args->bpp, 8);
> + unsigned int align = xlnx_get_align(drm);
> +
> + if (!args->pitch || !IS_ALIGNED(args->pitch, align))
> + args->pitch = ALIGN(pitch, align);
> +
> + return drm_gem_cma_dumb_create_internal(file_priv, drm, args);
> +}
> diff --git a/drivers/gpu/drm/xlnx/xlnx_gem.h b/drivers/gpu/drm/xlnx/xlnx_gem.h
> new file mode 100644
> index 0000000..f380de9
> --- /dev/null
> +++ b/drivers/gpu/drm/xlnx/xlnx_gem.h
> @@ -0,0 +1,26 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Xilinx DRM KMS GEM helper header
> + *
> + * Copyright (C) 2015 - 2018 Xilinx, Inc.
> + *
> + * Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#ifndef _XLNX_GEM_H_
> +#define _XLNX_GEM_H_
> +
> +int xlnx_gem_cma_dumb_create(struct drm_file *file_priv,
> + struct drm_device *drm,
> + struct drm_mode_create_dumb *args);
> +
> +#endif /* _XLNX_GEM_H_ */
> --
> 2.7.4
>
> This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
--
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v3 1/8] dt-bindings: display: xlnx: Add bindings for Xilinx display pipeline
2018-01-16 1:57 [PATCH v3 1/8] dt-bindings: display: xlnx: Add bindings for Xilinx display pipeline Hyun Kwon
` (2 preceding siblings ...)
2018-01-16 1:57 ` [PATCH v3 8/8] drm: xlnx: zynqmp_dp: " Hyun Kwon
@ 2018-01-19 23:32 ` Rob Herring
2018-01-20 2:22 ` Hyun Kwon
3 siblings, 1 reply; 17+ messages in thread
From: Rob Herring @ 2018-01-19 23:32 UTC (permalink / raw)
To: Hyun Kwon
Cc: devicetree, Laurent Pinchart, Michal Simek, dri-devel, Daniel Vetter
On Mon, Jan 15, 2018 at 05:57:04PM -0800, Hyun Kwon wrote:
> The dt binding for Xilinx display pipeline. The pipeline can be
> composed with multiple and different types of sub-devices. This node
> is to represent the entire pipeline as a single entity.
>
> Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
> ---
> v2
> - Remove linux specific terms
> - Elaborate details, ex regarding port binding
> - Rename xlnx,kms to xlnx,display
> - Rename the file name to xlnx,display.txt
> - Add examples of hardware blocks
> ---
> ---
> .../bindings/display/xlnx/xlnx,display.txt | 68 ++++++++++++++++++++++
> 1 file changed, 68 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/display/xlnx/xlnx,display.txt
>
> diff --git a/Documentation/devicetree/bindings/display/xlnx/xlnx,display.txt b/Documentation/devicetree/bindings/display/xlnx/xlnx,display.txt
> new file mode 100644
> index 0000000..fde1a35
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/xlnx/xlnx,display.txt
> @@ -0,0 +1,68 @@
> +Xilinx Display Pipeline
> +-----------------------
> +
> +Xilinx display pipeline can be designed with various types of multiple IPs:
> +IPs hardened on chip, ob board IPs, and soft IPs in programmable logic.
s/ob board/on-board/
> +While each component would need its own node, this node represents
> +a whole display pipeline as a single entity by integrating individual subdevice
> +with glue logics.
> +
> +The following illustrates some examples of topology:
> +
> +A linear pipeline with multiple blocks:
> +
> + SoC DMA -> SoC display controller -> SoC display enc
> +or,
> + FPGA DMA -> FPGA display controller -> FPGA display enc
> +
> +A pipeline with branches:
> +
> + SoC DMA -> SoC display controller -> SoC display enc
> + |
> + FPGA DMA->
> +or,
> + SoC DMA -> SoC display controller -> SoC display enc
> + |
> + -> FPAG display enc
s/FPAG/FPGA/
> +
> +or,
> +
> + SoC DMA -> SoC display controller -> SoC display enc
> + | |
> + FPGA display controller -> -> FPGA display enc
> +
> +Required properties:
> +
> +- compatible: Must be "xlnx,display".
> +
> +- ports: phandles for ports of display controller subdevice.
> + In the display controller port nodes, topology for entire pipeline
> + should be described using the DT bindings defined in
> + Documentation/devicetree/bindings/graph.txt.
> +
> +Example:
> +
> + xlnx_display {
> + compatible = "xlnx,display";
> + ports = <&display_controller_port>;
I still don't think you need this node. Match the DRM driver with the
display controller node.
> + };
> +
> + display_controller {
display-controller@???
Please show at least the compatible and reg in the example.
> + ...
> + display_controller_port: port@0 {
Unit address is not needed here. If you have a unit address, then you
should have a reg property (and #size-cells and #address-cells in the
parent).
> + display_controller_ep: endpoint {
> + remote-endpoint = <&dp_controller_ep>;
> + };
> + };
> + ...
> + };
> +
> + dp_controller {
> + ...
> + dp_controller_port: port@0 {
> + dp_controller_ep: endpoint {
> + remote-endpoint = <&display_controller_ep>;
> + };
> + };
> + ...
> + };
> --
> 2.7.4
>
> This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v3 2/8] drm: xlnx: Xilinx DRM KMS driver
2018-01-17 8:20 ` Daniel Vetter
@ 2018-01-19 23:33 ` Rob Herring
[not found] ` <20180117082028.GC2759-dv86pmgwkMBes7Z6vYuT8azUEOm+Xw19@public.gmane.org>
1 sibling, 0 replies; 17+ messages in thread
From: Rob Herring @ 2018-01-19 23:33 UTC (permalink / raw)
To: Daniel Vetter
Cc: devicetree, Hyun Kwon, Daniel Vetter, Michal Simek, dri-devel,
Laurent Pinchart
On Wed, Jan 17, 2018 at 09:20:28AM +0100, Daniel Vetter wrote:
> On Mon, Jan 15, 2018 at 05:57:05PM -0800, Hyun Kwon wrote:
> > Xilinx has various platforms for display, where users can create
> > using multiple IPs in the programmable FPGA fabric, or where
> > some hardened piepline is available on the chip. Furthermore,
> > hardened pipeline can also interact with soft logics in FPGA.
> >
> > The Xilinx DRM KMS is to integrate multiple subdevices and to represent
> > the entire pipeline as a single DRM device. The driver includes helpers
> > (ex, framebuffer and gem helpers) and glue logics (ex, crtc interface).
> >
> > Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
> > ---
> > v3
> > - Add Laurent as a maintainer
> > - Fix multiple-reference on gem objects
> > v2
> > - Change the SPDX identifier format
> > - Merge patches(crtc, gem, fb) into single one
> > v2 of xlnx_drv
> > - Rename kms to display in xlnx_drv
> > - Replace some xlnx specific fb helper with common helpers in xlnx_drv
> > - Don't set the commit tail callback in xlnx_drv
> > - Support 'ports' graph binding in xlnx_drv
> > v2 of xlnx_fb
> > - Remove wrappers in xlnx_fb
> > - Replace some functions with drm core helpers in xlnx_fb
> > ---
> > ---
> > MAINTAINERS | 9 +
> > drivers/gpu/drm/Kconfig | 2 +
> > drivers/gpu/drm/Makefile | 1 +
> > drivers/gpu/drm/xlnx/Kconfig | 12 ++
> > drivers/gpu/drm/xlnx/Makefile | 2 +
> > drivers/gpu/drm/xlnx/xlnx_crtc.c | 203 ++++++++++++++++++
> > drivers/gpu/drm/xlnx/xlnx_crtc.h | 78 +++++++
> > drivers/gpu/drm/xlnx/xlnx_drv.c | 447 +++++++++++++++++++++++++++++++++++++++
> > drivers/gpu/drm/xlnx/xlnx_drv.h | 30 +++
> > drivers/gpu/drm/xlnx/xlnx_fb.c | 298 ++++++++++++++++++++++++++
> > drivers/gpu/drm/xlnx/xlnx_fb.h | 33 +++
> > drivers/gpu/drm/xlnx/xlnx_gem.c | 47 ++++
> > drivers/gpu/drm/xlnx/xlnx_gem.h | 26 +++
> > 13 files changed, 1188 insertions(+)
> > create mode 100644 drivers/gpu/drm/xlnx/Kconfig
> > create mode 100644 drivers/gpu/drm/xlnx/Makefile
> > create mode 100644 drivers/gpu/drm/xlnx/xlnx_crtc.c
> > create mode 100644 drivers/gpu/drm/xlnx/xlnx_crtc.h
> > create mode 100644 drivers/gpu/drm/xlnx/xlnx_drv.c
> > create mode 100644 drivers/gpu/drm/xlnx/xlnx_drv.h
> > create mode 100644 drivers/gpu/drm/xlnx/xlnx_fb.c
> > create mode 100644 drivers/gpu/drm/xlnx/xlnx_fb.h
> > create mode 100644 drivers/gpu/drm/xlnx/xlnx_gem.c
> > create mode 100644 drivers/gpu/drm/xlnx/xlnx_gem.h
> >
> > diff --git a/MAINTAINERS b/MAINTAINERS
> > index 2811a21..dc84346 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -4682,6 +4682,15 @@ F: drivers/gpu/drm/etnaviv/
> > F: include/uapi/drm/etnaviv_drm.h
> > F: Documentation/devicetree/bindings/display/etnaviv/
> >
> > +DRM DRIVERS FOR XILINX
> > +M: Hyun Kwon <hyun.kwon@xilinx.com>
> > +M: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> > +L: dri-devel@lists.freedesktop.org
> > +S: Maintained
> > +F: drivers/gpu/drm/xlnx/
> > +F: Documentation/devicetree/bindings/display/xlnx/
> > +T: git git://anongit.freedesktop.org/drm/drm-misc
>
> Ok, I scrolled through the patches again and besides the one nit for the
> enable/disable_vblank callback it looks all good. On patches 2 and 4-6:
>
> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
>
> These are ready for merging. The 2 dt patches need an ack from Rob
> Herring. The final 2 patches with the new properties need the usual uapi
> work and userspace enabling per
The binding needs some work still.
Rob
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v3 3/8] dt-bindings: display: xlnx: Add ZynqMP DP subsystem bindings
[not found] ` <1516067831-11382-3-git-send-email-hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
@ 2018-01-20 0:31 ` Rob Herring
2018-01-20 2:22 ` Hyun Kwon
0 siblings, 1 reply; 17+ messages in thread
From: Rob Herring @ 2018-01-20 0:31 UTC (permalink / raw)
To: Hyun Kwon
Cc: dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW,
devicetree-u79uwXL29TY76Z2rM5mHXA, Michal Simek, Daniel Vetter,
Laurent Pinchart
On Mon, Jan 15, 2018 at 05:57:06PM -0800, Hyun Kwon wrote:
> This add a dt binding for ZynqMP DP subsystem.
>
> Signed-off-by: Hyun Kwon <hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
> ---
> v2
> - Group multiple ports under 'ports'
> - Replace linux specific terms with generic hardware descriptions
> ---
> ---
> .../bindings/display/xlnx/xlnx,zynqmp-dpsub.txt | 98 ++++++++++++++++++++++
> 1 file changed, 98 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.txt
>
> diff --git a/Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.txt b/Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.txt
> new file mode 100644
> index 0000000..dbcbde5
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.txt
> @@ -0,0 +1,98 @@
> +Xilinx ZynqMP DisplayPort subsystem
> +-----------------------------------
> +
> +Required properties:
> +
> +- compatible: Must be "xlnx,zynqmp-dpsub-1.7".
> +
> +- reg: Physical base address and length of the registers set for the device.
> +- reg-names: Must be "dp", "blend", "av_buf", and "aud" to map logical register
> + partitions.
> +
> +- interrupts: Interrupt number.
> +- interrupts-parent: phandle for interrupt controller.
> +
> +- clocks: phandles for axi, audio, non-live video, and live video clocks.
> + axi clock is required. Audio clock is optional. If not present, audio will
> + be disabled. One of non-live or live video clock should be present.
> +- clock-names: The identification strings are required. "aclk" for axi clock.
> + "dp_aud_clk" for audio clock. "dp_vtc_pixel_clk_in" for non-live video clock.
> + "dp_live_video_in_clk" for live video clock (clock from programmable logic).
> +
> +- phys: phandles for phy specifier.
phandles? How many?
> +- phy-names: The identifier strings. "dp-phy" followed by index.
> +
> +- power-domains: phandle for the corresponding power domain
> +
> +- ports: There are 2 logical blocks in the IP: display controller and
> + DisplayPort encoder. Each block can be used / connected independently with
I'm confused. The block described in this doc is just DisplayPort
encoder or both display controller and DisplayPort? Or something else?
> + external device, hence ports for each block are required using DT bindings
> + defined in Documentation/devicetree/bindings/graph.txt. Refer to
> + ./xlnx,display.txt for how topology for entire pipeline is described.
> +
> +- vid-layer, gfx-layer: Required to represent available layers
> +
> +Required layer properties
> +
> +- dmas: phandles for DMA channels as defined in
> + Documentation/devicetree/bindings/dma/dma.txt.
> +- dma-names: The identifier strings are required. "graphics0" for graphics
> + layer. "video" followed by index for video layer
> +
> +Optional child node
> +
> +- The driver populates any child device node in this node. This can be used,
> + for example, to populate the sound device from the DisplayPort subsystem
> + driver.
> +
> +Example:
> + zynqmp_dpsub: zynqmp_dpsub@fd4a0000 {
video-codec@... if this the DP encoder.
> + compatible = "xlnx,zynqmp-dpsub-1.7";
> + reg = <0x0 0xfd4a0000 0x0 0x1000>,
> + <0x0 0xfd4aa000 0x0 0x1000>,
> + <0x0 0xfd4ab000 0x0 0x1000>,
> + <0x0 0xfd4ac000 0x0 0x1000>;
> + reg-names = "dp", "blend", "av_buf", "aud";
> + interrupts = <0 119 4>;
> + interrupt-parent = <&gic>;
> +
> + clock-names = "dp_apb_clk", "dp_aud_clk", "dp_live_video_in_clk";
> + clocks = <&dp_aclk>, <&clkc 17>, <&si570_1>;
> +
> + phys = <&lane1>, <&lane0>;
> + phy-names = "dp-phy0", "dp-phy1";
> +
> + power-domains = <&pd_dp>;
> +
> + vid-layer {
> + dma-names = "vid0", "vid1", "vid2";
Documentation says these should be "videoX".
> + dmas = <&xlnx_dpdma 0>,
> + <&xlnx_dpdma 1>,
> + <&xlnx_dpdma 2>;
> + };
> +
> + gfx-layer {
> + dma-names = "gfx0";
And "graphics0"
> + dmas = <&xlnx_dpdma 3>;
> + };
You don't need these child nodes. Just do:
dma-names = "vid0", "vid1", "vid2", "gfx0";
Or gfx0 first.
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + display_port: port@0 {
> + reg = <0>;
> + display_port: endpoint {
> + remote-endpoint = <&dp_port>;
> + };
> + };
> + port@1 {
> + reg = <1>;
> + dp_port: endpoint {
> + remote-endpoint = <&display_port>;
> + };
> + };
> + }
> + };
> +};
> +
> --
> 2.7.4
>
> This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 17+ messages in thread
* RE: [PATCH v3 3/8] dt-bindings: display: xlnx: Add ZynqMP DP subsystem bindings
2018-01-20 0:31 ` Rob Herring
@ 2018-01-20 2:22 ` Hyun Kwon
2018-01-22 14:36 ` Rob Herring
0 siblings, 1 reply; 17+ messages in thread
From: Hyun Kwon @ 2018-01-20 2:22 UTC (permalink / raw)
To: Rob Herring
Cc: Daniel Vetter, devicetree, Laurent Pinchart, dri-devel, Michal Simek
Hi Rob,
Thanks for the review.
> -----Original Message-----
> From: dri-devel [mailto:dri-devel-bounces@lists.freedesktop.org] On Behalf
> Of Rob Herring
> Sent: Friday, January 19, 2018 4:31 PM
> To: Hyun Kwon <hyunk@xilinx.com>
> Cc: devicetree@vger.kernel.org; Laurent Pinchart
> <laurent.pinchart@ideasonboard.com>; Michal Simek
> <michal.simek@xilinx.com>; dri-devel@lists.freedesktop.org; Daniel Vetter
> <daniel.vetter@ffwll.ch>
> Subject: Re: [PATCH v3 3/8] dt-bindings: display: xlnx: Add ZynqMP DP
> subsystem bindings
>
> On Mon, Jan 15, 2018 at 05:57:06PM -0800, Hyun Kwon wrote:
> > This add a dt binding for ZynqMP DP subsystem.
> >
> > Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
> > ---
> > v2
> > - Group multiple ports under 'ports'
> > - Replace linux specific terms with generic hardware descriptions
> > ---
> > ---
> > .../bindings/display/xlnx/xlnx,zynqmp-dpsub.txt | 98
> ++++++++++++++++++++++
> > 1 file changed, 98 insertions(+)
> > create mode 100644
> Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.txt
> >
> > diff --git a/Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-
> dpsub.txt b/Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-
> dpsub.txt
> > new file mode 100644
> > index 0000000..dbcbde5
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-
> dpsub.txt
> > @@ -0,0 +1,98 @@
> > +Xilinx ZynqMP DisplayPort subsystem
> > +-----------------------------------
> > +
> > +Required properties:
> > +
> > +- compatible: Must be "xlnx,zynqmp-dpsub-1.7".
> > +
> > +- reg: Physical base address and length of the registers set for the device.
> > +- reg-names: Must be "dp", "blend", "av_buf", and "aud" to map logical
> register
> > + partitions.
> > +
> > +- interrupts: Interrupt number.
> > +- interrupts-parent: phandle for interrupt controller.
> > +
> > +- clocks: phandles for axi, audio, non-live video, and live video clocks.
> > + axi clock is required. Audio clock is optional. If not present, audio will
> > + be disabled. One of non-live or live video clock should be present.
> > +- clock-names: The identification strings are required. "aclk" for axi clock.
> > + "dp_aud_clk" for audio clock. "dp_vtc_pixel_clk_in" for non-live video
> clock.
> > + "dp_live_video_in_clk" for live video clock (clock from programmable
> logic).
> > +
> > +- phys: phandles for phy specifier.
>
> phandles? How many?
>
Configurable between 1 or 2 lanes. Will add more details.
> > +- phy-names: The identifier strings. "dp-phy" followed by index.
> > +
> > +- power-domains: phandle for the corresponding power domain
> > +
> > +- ports: There are 2 logical blocks in the IP: display controller and
> > + DisplayPort encoder. Each block can be used / connected independently
> with
>
> I'm confused. The block described in this doc is just DisplayPort
> encoder or both display controller and DisplayPort? Or something else?
>
The DP subsystem includes both block, protocol indipendent controller in front
and the DisplayPort transmitter in the back. I'll try to elaborate / clarify
better.
> > + external device, hence ports for each block are required using DT
> bindings
> > + defined in Documentation/devicetree/bindings/graph.txt. Refer to
> > + ./xlnx,display.txt for how topology for entire pipeline is described.
> > +
> > +- vid-layer, gfx-layer: Required to represent available layers
> > +
> > +Required layer properties
> > +
> > +- dmas: phandles for DMA channels as defined in
> > + Documentation/devicetree/bindings/dma/dma.txt.
> > +- dma-names: The identifier strings are required. "graphics0" for graphics
> > + layer. "video" followed by index for video layer
> > +
> > +Optional child node
> > +
> > +- The driver populates any child device node in this node. This can be
> used,
> > + for example, to populate the sound device from the DisplayPort
> subsystem
> > + driver.
> > +
> > +Example:
> > + zynqmp_dpsub: zynqmp_dpsub@fd4a0000 {
>
> video-codec@... if this the DP encoder.
>
> > + compatible = "xlnx,zynqmp-dpsub-1.7";
> > + reg = <0x0 0xfd4a0000 0x0 0x1000>,
> > + <0x0 0xfd4aa000 0x0 0x1000>,
> > + <0x0 0xfd4ab000 0x0 0x1000>,
> > + <0x0 0xfd4ac000 0x0 0x1000>;
> > + reg-names = "dp", "blend", "av_buf", "aud";
> > + interrupts = <0 119 4>;
> > + interrupt-parent = <&gic>;
> > +
> > + clock-names = "dp_apb_clk", "dp_aud_clk",
> "dp_live_video_in_clk";
> > + clocks = <&dp_aclk>, <&clkc 17>, <&si570_1>;
> > +
> > + phys = <&lane1>, <&lane0>;
> > + phy-names = "dp-phy0", "dp-phy1";
> > +
> > + power-domains = <&pd_dp>;
> > +
> > + vid-layer {
> > + dma-names = "vid0", "vid1", "vid2";
>
> Documentation says these should be "videoX".
>
Will fix.
> > + dmas = <&xlnx_dpdma 0>,
> > + <&xlnx_dpdma 1>,
> > + <&xlnx_dpdma 2>;
> > + };
> > +
> > + gfx-layer {
> > + dma-names = "gfx0";
>
> And "graphics0"
>
Will fix.
> > + dmas = <&xlnx_dpdma 3>;
> > + };
>
> You don't need these child nodes. Just do:
>
> dma-names = "vid0", "vid1", "vid2", "gfx0";
>
> Or gfx0 first.
>
Sure. As mentioned earlier, each layer will have to be referenced independently
by other nodes in upcoming patches. But I can follow your suggestion for now,
and make change when it's needed.
Thanks,
-hyun
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 17+ messages in thread
* RE: [PATCH v3 1/8] dt-bindings: display: xlnx: Add bindings for Xilinx display pipeline
2018-01-19 23:32 ` [PATCH v3 1/8] dt-bindings: display: xlnx: Add bindings for Xilinx display pipeline Rob Herring
@ 2018-01-20 2:22 ` Hyun Kwon
0 siblings, 0 replies; 17+ messages in thread
From: Hyun Kwon @ 2018-01-20 2:22 UTC (permalink / raw)
To: Rob Herring
Cc: devicetree, Laurent Pinchart, Michal Simek, dri-devel, Daniel Vetter
Hi Rob,
Thanks for the review.
> -----Original Message-----
> From: Rob Herring [mailto:robh@kernel.org]
> Sent: Friday, January 19, 2018 3:33 PM
> To: Hyun Kwon <hyunk@xilinx.com>
> Cc: dri-devel@lists.freedesktop.org; devicetree@vger.kernel.org; Michal
> Simek <michal.simek@xilinx.com>; Daniel Vetter <daniel.vetter@ffwll.ch>;
> Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Subject: Re: [PATCH v3 1/8] dt-bindings: display: xlnx: Add bindings for
> Xilinx display pipeline
>
> On Mon, Jan 15, 2018 at 05:57:04PM -0800, Hyun Kwon wrote:
> > The dt binding for Xilinx display pipeline. The pipeline can be
> > composed with multiple and different types of sub-devices. This node
> > is to represent the entire pipeline as a single entity.
> >
> > Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
> > ---
> > v2
> > - Remove linux specific terms
> > - Elaborate details, ex regarding port binding
> > - Rename xlnx,kms to xlnx,display
> > - Rename the file name to xlnx,display.txt
> > - Add examples of hardware blocks
> > ---
> > ---
> > .../bindings/display/xlnx/xlnx,display.txt | 68
> ++++++++++++++++++++++
> > 1 file changed, 68 insertions(+)
> > create mode 100644
> Documentation/devicetree/bindings/display/xlnx/xlnx,display.txt
> >
> > diff --git
> a/Documentation/devicetree/bindings/display/xlnx/xlnx,display.txt
> b/Documentation/devicetree/bindings/display/xlnx/xlnx,display.txt
> > new file mode 100644
> > index 0000000..fde1a35
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/xlnx/xlnx,display.txt
> > @@ -0,0 +1,68 @@
> > +Xilinx Display Pipeline
> > +-----------------------
> > +
> > +Xilinx display pipeline can be designed with various types of multiple IPs:
> > +IPs hardened on chip, ob board IPs, and soft IPs in programmable logic.
>
> s/ob board/on-board/
>
Will fix it.
> > +While each component would need its own node, this node represents
> > +a whole display pipeline as a single entity by integrating individual
> subdevice
> > +with glue logics.
> > +
> > +The following illustrates some examples of topology:
> > +
> > +A linear pipeline with multiple blocks:
> > +
> > + SoC DMA -> SoC display controller -> SoC display enc
> > +or,
> > + FPGA DMA -> FPGA display controller -> FPGA display enc
> > +
> > +A pipeline with branches:
> > +
> > + SoC DMA -> SoC display controller -> SoC display enc
> > + |
> > + FPGA DMA->
> > +or,
> > + SoC DMA -> SoC display controller -> SoC display enc
> > + |
> > + -> FPAG display enc
>
> s/FPAG/FPGA/
>
Will fix.
> > +
> > +or,
> > +
> > + SoC DMA -> SoC display controller -> SoC display enc
> > + | |
> > + FPGA display controller -> -> FPGA display enc
> > +
> > +Required properties:
> > +
> > +- compatible: Must be "xlnx,display".
> > +
> > +- ports: phandles for ports of display controller subdevice.
> > + In the display controller port nodes, topology for entire pipeline
> > + should be described using the DT bindings defined in
> > + Documentation/devicetree/bindings/graph.txt.
> > +
> > +Example:
> > +
> > + xlnx_display {
> > + compatible = "xlnx,display";
> > + ports = <&display_controller_port>;
>
> I still don't think you need this node. Match the DRM driver with the
> display controller node.
>
With that approach, it becomes tricky as multiple devices can form a single
DRM device (single pipeline). For example, the SoC display controller would
match the DRM driver when it's used alone. There can be a standalone FPGA
display controller which will match the DRM driver. But there can also be
a design where both controllers are connected together and share some block,
ex DisplayPort transmitter. There it's not clear which one to match
the DRM driver. Thus this logical node helps to represent fragmented devices
as a single device display pipeline. If this is not acceptable, I'll try to
find other options.
> > + };
> > +
> > + display_controller {
>
> display-controller@???
>
> Please show at least the compatible and reg in the example.
>
Sure will do.
> > + ...
> > + display_controller_port: port@0 {
>
> Unit address is not needed here. If you have a unit address, then you
> should have a reg property (and #size-cells and #address-cells in the
> parent).
>
Will fix.
Thanks,
-hyun
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v3 3/8] dt-bindings: display: xlnx: Add ZynqMP DP subsystem bindings
2018-01-20 2:22 ` Hyun Kwon
@ 2018-01-22 14:36 ` Rob Herring
0 siblings, 0 replies; 17+ messages in thread
From: Rob Herring @ 2018-01-22 14:36 UTC (permalink / raw)
To: Hyun Kwon
Cc: devicetree, Laurent Pinchart, Michal Simek, dri-devel, Daniel Vetter
On Fri, Jan 19, 2018 at 8:22 PM, Hyun Kwon <hyunk@xilinx.com> wrote:
> Hi Rob,
>
> Thanks for the review.
>
>> -----Original Message-----
>> From: dri-devel [mailto:dri-devel-bounces@lists.freedesktop.org] On Behalf
>> Of Rob Herring
>> Sent: Friday, January 19, 2018 4:31 PM
>> To: Hyun Kwon <hyunk@xilinx.com>
>> Cc: devicetree@vger.kernel.org; Laurent Pinchart
>> <laurent.pinchart@ideasonboard.com>; Michal Simek
>> <michal.simek@xilinx.com>; dri-devel@lists.freedesktop.org; Daniel Vetter
>> <daniel.vetter@ffwll.ch>
>> Subject: Re: [PATCH v3 3/8] dt-bindings: display: xlnx: Add ZynqMP DP
>> subsystem bindings
>>
>> On Mon, Jan 15, 2018 at 05:57:06PM -0800, Hyun Kwon wrote:
>> > This add a dt binding for ZynqMP DP subsystem.
>> >
>> > Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
>> > ---
>> > v2
>> > - Group multiple ports under 'ports'
>> > - Replace linux specific terms with generic hardware descriptions
>> > ---
>> > ---
>> > .../bindings/display/xlnx/xlnx,zynqmp-dpsub.txt | 98
>> ++++++++++++++++++++++
>> > 1 file changed, 98 insertions(+)
>> > create mode 100644
>> Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.txt
>> >
>> > diff --git a/Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-
>> dpsub.txt b/Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-
>> dpsub.txt
>> > new file mode 100644
>> > index 0000000..dbcbde5
>> > --- /dev/null
>> > +++ b/Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-
>> dpsub.txt
>> > @@ -0,0 +1,98 @@
>> > +Xilinx ZynqMP DisplayPort subsystem
>> > +-----------------------------------
>> > +
>> > +Required properties:
>> > +
>> > +- compatible: Must be "xlnx,zynqmp-dpsub-1.7".
>> > +
>> > +- reg: Physical base address and length of the registers set for the device.
>> > +- reg-names: Must be "dp", "blend", "av_buf", and "aud" to map logical
>> register
>> > + partitions.
>> > +
>> > +- interrupts: Interrupt number.
>> > +- interrupts-parent: phandle for interrupt controller.
>> > +
>> > +- clocks: phandles for axi, audio, non-live video, and live video clocks.
>> > + axi clock is required. Audio clock is optional. If not present, audio will
>> > + be disabled. One of non-live or live video clock should be present.
>> > +- clock-names: The identification strings are required. "aclk" for axi clock.
>> > + "dp_aud_clk" for audio clock. "dp_vtc_pixel_clk_in" for non-live video
>> clock.
>> > + "dp_live_video_in_clk" for live video clock (clock from programmable
>> logic).
>> > +
>> > +- phys: phandles for phy specifier.
>>
>> phandles? How many?
>>
>
> Configurable between 1 or 2 lanes. Will add more details.
>
>> > +- phy-names: The identifier strings. "dp-phy" followed by index.
>> > +
>> > +- power-domains: phandle for the corresponding power domain
>> > +
>> > +- ports: There are 2 logical blocks in the IP: display controller and
>> > + DisplayPort encoder. Each block can be used / connected independently
>> with
>>
>> I'm confused. The block described in this doc is just DisplayPort
>> encoder or both display controller and DisplayPort? Or something else?
>>
>
> The DP subsystem includes both block, protocol indipendent controller in front
> and the DisplayPort transmitter in the back. I'll try to elaborate / clarify
> better.
But you already have a subsystem node with "xlnx,display". You shouldn't need 2.
>> > + external device, hence ports for each block are required using DT
>> bindings
>> > + defined in Documentation/devicetree/bindings/graph.txt. Refer to
>> > + ./xlnx,display.txt for how topology for entire pipeline is described.
>> > +
>> > +- vid-layer, gfx-layer: Required to represent available layers
>> > +
>> > +Required layer properties
>> > +
>> > +- dmas: phandles for DMA channels as defined in
>> > + Documentation/devicetree/bindings/dma/dma.txt.
>> > +- dma-names: The identifier strings are required. "graphics0" for graphics
>> > + layer. "video" followed by index for video layer
>> > +
>> > +Optional child node
>> > +
>> > +- The driver populates any child device node in this node. This can be
>> used,
>> > + for example, to populate the sound device from the DisplayPort
>> subsystem
>> > + driver.
>> > +
>> > +Example:
>> > + zynqmp_dpsub: zynqmp_dpsub@fd4a0000 {
>>
>> video-codec@... if this the DP encoder.
>>
>> > + compatible = "xlnx,zynqmp-dpsub-1.7";
>> > + reg = <0x0 0xfd4a0000 0x0 0x1000>,
>> > + <0x0 0xfd4aa000 0x0 0x1000>,
>> > + <0x0 0xfd4ab000 0x0 0x1000>,
>> > + <0x0 0xfd4ac000 0x0 0x1000>;
>> > + reg-names = "dp", "blend", "av_buf", "aud";
>> > + interrupts = <0 119 4>;
>> > + interrupt-parent = <&gic>;
>> > +
>> > + clock-names = "dp_apb_clk", "dp_aud_clk",
>> "dp_live_video_in_clk";
>> > + clocks = <&dp_aclk>, <&clkc 17>, <&si570_1>;
>> > +
>> > + phys = <&lane1>, <&lane0>;
>> > + phy-names = "dp-phy0", "dp-phy1";
>> > +
>> > + power-domains = <&pd_dp>;
>> > +
>> > + vid-layer {
>> > + dma-names = "vid0", "vid1", "vid2";
>>
>> Documentation says these should be "videoX".
>>
>
> Will fix.
>
>> > + dmas = <&xlnx_dpdma 0>,
>> > + <&xlnx_dpdma 1>,
>> > + <&xlnx_dpdma 2>;
>> > + };
>> > +
>> > + gfx-layer {
>> > + dma-names = "gfx0";
>>
>> And "graphics0"
>>
>
> Will fix.
>
>> > + dmas = <&xlnx_dpdma 3>;
>> > + };
>>
>> You don't need these child nodes. Just do:
>>
>> dma-names = "vid0", "vid1", "vid2", "gfx0";
>>
>> Or gfx0 first.
>>
>
> Sure. As mentioned earlier, each layer will have to be referenced independently
> by other nodes in upcoming patches. But I can follow your suggestion for now,
> and make change when it's needed.
No, you can't change it later. The binding is an ABI and you must maintain backwards compatibility (old dtb works with new kernel).
So you should make your binding complete as you can now even if the driver doesn't use parts of the binding yet.
Rob
^ permalink raw reply [flat|nested] 17+ messages in thread
* RE: [PATCH v3 2/8] drm: xlnx: Xilinx DRM KMS driver
[not found] ` <20180117082028.GC2759-dv86pmgwkMBes7Z6vYuT8azUEOm+Xw19@public.gmane.org>
@ 2018-01-26 1:36 ` Hyun Kwon
0 siblings, 0 replies; 17+ messages in thread
From: Hyun Kwon @ 2018-01-26 1:36 UTC (permalink / raw)
To: Daniel Vetter
Cc: dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW,
devicetree-u79uwXL29TY76Z2rM5mHXA, Michal Simek, Rob Herring,
Daniel Vetter, Laurent Pinchart
Hi Daniel,
> -----Original Message-----
> From: Daniel Vetter [mailto:daniel.vetter@ffwll.ch] On Behalf Of Daniel
> Vetter
> Sent: Wednesday, January 17, 2018 12:20 AM
> To: Hyun Kwon <hyunk@xilinx.com>
> Cc: dri-devel@lists.freedesktop.org; devicetree@vger.kernel.org; Michal
> Simek <michal.simek@xilinx.com>; Rob Herring <robh@kernel.org>; Daniel
> Vetter <daniel.vetter@ffwll.ch>; Laurent Pinchart
> <laurent.pinchart@ideasonboard.com>
> Subject: Re: [PATCH v3 2/8] drm: xlnx: Xilinx DRM KMS driver
>
> On Mon, Jan 15, 2018 at 05:57:05PM -0800, Hyun Kwon wrote:
> > Xilinx has various platforms for display, where users can create
> > using multiple IPs in the programmable FPGA fabric, or where
> > some hardened piepline is available on the chip. Furthermore,
> > hardened pipeline can also interact with soft logics in FPGA.
> >
> > The Xilinx DRM KMS is to integrate multiple subdevices and to represent
> > the entire pipeline as a single DRM device. The driver includes helpers
> > (ex, framebuffer and gem helpers) and glue logics (ex, crtc interface).
> >
> > Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
> > ---
> > v3
> > - Add Laurent as a maintainer
> > - Fix multiple-reference on gem objects
> > v2
> > - Change the SPDX identifier format
> > - Merge patches(crtc, gem, fb) into single one
> > v2 of xlnx_drv
> > - Rename kms to display in xlnx_drv
> > - Replace some xlnx specific fb helper with common helpers in xlnx_drv
> > - Don't set the commit tail callback in xlnx_drv
> > - Support 'ports' graph binding in xlnx_drv
> > v2 of xlnx_fb
> > - Remove wrappers in xlnx_fb
> > - Replace some functions with drm core helpers in xlnx_fb
> > ---
> > ---
> > MAINTAINERS | 9 +
> > drivers/gpu/drm/Kconfig | 2 +
> > drivers/gpu/drm/Makefile | 1 +
> > drivers/gpu/drm/xlnx/Kconfig | 12 ++
> > drivers/gpu/drm/xlnx/Makefile | 2 +
> > drivers/gpu/drm/xlnx/xlnx_crtc.c | 203 ++++++++++++++++++
> > drivers/gpu/drm/xlnx/xlnx_crtc.h | 78 +++++++
> > drivers/gpu/drm/xlnx/xlnx_drv.c | 447
> +++++++++++++++++++++++++++++++++++++++
> > drivers/gpu/drm/xlnx/xlnx_drv.h | 30 +++
> > drivers/gpu/drm/xlnx/xlnx_fb.c | 298 ++++++++++++++++++++++++++
> > drivers/gpu/drm/xlnx/xlnx_fb.h | 33 +++
> > drivers/gpu/drm/xlnx/xlnx_gem.c | 47 ++++
> > drivers/gpu/drm/xlnx/xlnx_gem.h | 26 +++
> > 13 files changed, 1188 insertions(+)
> > create mode 100644 drivers/gpu/drm/xlnx/Kconfig
> > create mode 100644 drivers/gpu/drm/xlnx/Makefile
> > create mode 100644 drivers/gpu/drm/xlnx/xlnx_crtc.c
> > create mode 100644 drivers/gpu/drm/xlnx/xlnx_crtc.h
> > create mode 100644 drivers/gpu/drm/xlnx/xlnx_drv.c
> > create mode 100644 drivers/gpu/drm/xlnx/xlnx_drv.h
> > create mode 100644 drivers/gpu/drm/xlnx/xlnx_fb.c
> > create mode 100644 drivers/gpu/drm/xlnx/xlnx_fb.h
> > create mode 100644 drivers/gpu/drm/xlnx/xlnx_gem.c
> > create mode 100644 drivers/gpu/drm/xlnx/xlnx_gem.h
> >
> > diff --git a/MAINTAINERS b/MAINTAINERS
> > index 2811a21..dc84346 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -4682,6 +4682,15 @@ F: drivers/gpu/drm/etnaviv/
> > F: include/uapi/drm/etnaviv_drm.h
> > F: Documentation/devicetree/bindings/display/etnaviv/
> >
> > +DRM DRIVERS FOR XILINX
> > +M: Hyun Kwon <hyun.kwon@xilinx.com>
> > +M: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> > +L: dri-devel@lists.freedesktop.org
> > +S: Maintained
> > +F: drivers/gpu/drm/xlnx/
> > +F: Documentation/devicetree/bindings/display/xlnx/
> > +T: git git://anongit.freedesktop.org/drm/drm-misc
>
> Ok, I scrolled through the patches again and besides the one nit for the
> enable/disable_vblank callback it looks all good. On patches 2 and 4-6:
>
> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
>
> These are ready for merging. The 2 dt patches need an ack from Rob
> Herring. The final 2 patches with the new properties need the usual uapi
> work and userspace enabling per
>
> https://dri.freedesktop.org/docs/drm/gpu/drm-uapi.html#open-source-
> userspace-requirements
>
> Since Laurent is listed as co-maintainer, and Laurent is already drm-misc
> committer I think it's indeed best to maintain it in there. Please request
> a new account per
>
> https://www.freedesktop.org/wiki/AccountRequests/
>
> and check out quickstart in
>
> https://01.org/linuxgraphics/gfx-docs/maintainer-
> tools/dim.html#quickstart
>
> For any questions I or Laurent should be able to help out. My expectation
> is that once you have the ack from DT maintainers you'll merge patches 1-6
> yourself directly.
>
> Thanks, Daniel
>
Thanks for the pointers and help.
I'll follow the process once bindings are accepted.
Thanks,
-hyun
> > +
> > DRM DRIVERS FOR ZTE ZX
> > M: Shawn Guo <shawnguo@kernel.org>
> > L: dri-devel@lists.freedesktop.org
> > diff --git a/drivers/gpu/drm/Kconfig b/drivers/gpu/drm/Kconfig
> > index 22ee5a1..f3c71e3 100644
> > --- a/drivers/gpu/drm/Kconfig
> > +++ b/drivers/gpu/drm/Kconfig
> > @@ -282,6 +282,8 @@ source "drivers/gpu/drm/tinydrm/Kconfig"
> >
> > source "drivers/gpu/drm/pl111/Kconfig"
> >
> > +source "drivers/gpu/drm/xlnx/Kconfig"
> > +
> > # Keep legacy drivers last
> >
> > menuconfig DRM_LEGACY
> > diff --git a/drivers/gpu/drm/Makefile b/drivers/gpu/drm/Makefile
> > index 92550dd..2f44c77 100644
> > --- a/drivers/gpu/drm/Makefile
> > +++ b/drivers/gpu/drm/Makefile
> > @@ -103,3 +103,4 @@ obj-$(CONFIG_DRM_ZTE) += zte/
> > obj-$(CONFIG_DRM_MXSFB) += mxsfb/
> > obj-$(CONFIG_DRM_TINYDRM) += tinydrm/
> > obj-$(CONFIG_DRM_PL111) += pl111/
> > +obj-$(CONFIG_DRM_XLNX) += xlnx/
> > diff --git a/drivers/gpu/drm/xlnx/Kconfig b/drivers/gpu/drm/xlnx/Kconfig
> > new file mode 100644
> > index 0000000..19fd7cd
> > --- /dev/null
> > +++ b/drivers/gpu/drm/xlnx/Kconfig
> > @@ -0,0 +1,12 @@
> > +config DRM_XLNX
> > + tristate "Xilinx DRM KMS Driver"
> > + depends on DRM && OF
> > + select DRM_KMS_HELPER
> > + select DRM_KMS_CMA_HELPER
> > + select DRM_GEM_CMA_HELPER
> > + help
> > + Xilinx DRM KMS driver. Choose this option if you have
> > + a Xilinx SoCs with hardened display pipeline or soft
> > + display pipeline using Xilinx IPs in FPGA. This module
> > + provides the kernel mode setting functionalities
> > + for Xilinx display drivers.
> > diff --git a/drivers/gpu/drm/xlnx/Makefile
> b/drivers/gpu/drm/xlnx/Makefile
> > new file mode 100644
> > index 0000000..c60a281
> > --- /dev/null
> > +++ b/drivers/gpu/drm/xlnx/Makefile
> > @@ -0,0 +1,2 @@
> > +xlnx_drm-objs += xlnx_crtc.o xlnx_drv.o xlnx_fb.o xlnx_gem.o
> > +obj-$(CONFIG_DRM_XLNX) += xlnx_drm.o
> > diff --git a/drivers/gpu/drm/xlnx/xlnx_crtc.c
> b/drivers/gpu/drm/xlnx/xlnx_crtc.c
> > new file mode 100644
> > index 0000000..89beb9e
> > --- /dev/null
> > +++ b/drivers/gpu/drm/xlnx/xlnx_crtc.c
> > @@ -0,0 +1,203 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Xilinx DRM crtc driver
> > + *
> > + * Copyright (C) 2017 - 2018 Xilinx, Inc.
> > + *
> > + * Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
> > + *
> > + * This software is licensed under the terms of the GNU General Public
> > + * License version 2, as published by the Free Software Foundation, and
> > + * may be copied, distributed, and modified under those terms.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + */
> > +
> > +#include <drm/drmP.h>
> > +
> > +#include <linux/list.h>
> > +
> > +#include "xlnx_crtc.h"
> > +#include "xlnx_drv.h"
> > +
> > +/*
> > + * Overview
> > + * --------
> > + *
> > + * The Xilinx CRTC layer is to enable the custom interface to CRTC drivers.
> > + * The interface is used by Xilinx DRM driver where it needs CRTC
> > + * functionailty. CRTC drivers should attach the desired callbacks
> > + * to struct xlnx_crtc and register the xlnx_crtc with correcsponding
> > + * drm_device. It's highly recommended CRTC drivers register all
> callbacks
> > + * even though many of them are optional.
> > + * The CRTC helper simply walks through the registered CRTC device,
> > + * and call the callbacks.
> > + */
> > +
> > +/**
> > + * struct xlnx_crtc_helper - Xilinx CRTC helper
> > + * @xlnx_crtcs: list of Xilinx CRTC devices
> > + * @lock: lock to protect @xlnx_crtcs
> > + * @drm: back pointer to DRM core
> > + */
> > +struct xlnx_crtc_helper {
> > + struct list_head xlnx_crtcs;
> > + struct mutex lock; /* lock for @xlnx_crtcs */
> > + struct drm_device *drm;
> > +};
> > +
> > +#define XLNX_CRTC_MAX_HEIGHT_WIDTH UINT_MAX
> > +
> > +int xlnx_crtc_helper_enable_vblank(struct xlnx_crtc_helper *helper,
> > + unsigned int crtc_id)
> > +{
> > + struct xlnx_crtc *crtc;
> > +
> > + list_for_each_entry(crtc, &helper->xlnx_crtcs, list)
> > + if (drm_crtc_index(&crtc->crtc) == crtc_id)
> > + if (crtc->enable_vblank)
> > + return crtc->enable_vblank(crtc);
> > + return -ENODEV;
> > +}
> > +
> > +void xlnx_crtc_helper_disable_vblank(struct xlnx_crtc_helper *helper,
> > + unsigned int crtc_id)
> > +{
> > + struct xlnx_crtc *crtc;
> > +
> > + list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
> > + if (drm_crtc_index(&crtc->crtc) == crtc_id) {
> > + if (crtc->disable_vblank)
> > + crtc->disable_vblank(crtc);
> > + return;
> > + }
> > + }
> > +}
> > +
> > +unsigned int xlnx_crtc_helper_get_align(struct xlnx_crtc_helper *helper)
> > +{
> > + struct xlnx_crtc *crtc;
> > + unsigned int align = 1, tmp;
> > +
> > + list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
> > + if (crtc->get_align) {
> > + tmp = crtc->get_align(crtc);
> > + align = ALIGN(align, tmp);
> > + }
> > + }
> > +
> > + return align;
> > +}
> > +
> > +u64 xlnx_crtc_helper_get_dma_mask(struct xlnx_crtc_helper *helper)
> > +{
> > + struct xlnx_crtc *crtc;
> > + u64 mask = DMA_BIT_MASK(sizeof(dma_addr_t) * 8), tmp;
> > +
> > + list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
> > + if (crtc->get_dma_mask) {
> > + tmp = crtc->get_dma_mask(crtc);
> > + mask = min(mask, tmp);
> > + }
> > + }
> > +
> > + return mask;
> > +}
> > +
> > +int xlnx_crtc_helper_get_max_width(struct xlnx_crtc_helper *helper)
> > +{
> > + struct xlnx_crtc *crtc;
> > + unsigned int width = XLNX_CRTC_MAX_HEIGHT_WIDTH, tmp;
> > +
> > + list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
> > + if (crtc->get_max_width) {
> > + tmp = crtc->get_max_width(crtc);
> > + width = min(width, tmp);
> > + }
> > + }
> > +
> > + return width;
> > +}
> > +
> > +int xlnx_crtc_helper_get_max_height(struct xlnx_crtc_helper *helper)
> > +{
> > + struct xlnx_crtc *crtc;
> > + unsigned int height = XLNX_CRTC_MAX_HEIGHT_WIDTH, tmp;
> > +
> > + list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
> > + if (crtc->get_max_height) {
> > + tmp = crtc->get_max_height(crtc);
> > + height = min(height, tmp);
> > + }
> > + }
> > +
> > + return height;
> > +}
> > +
> > +uint32_t xlnx_crtc_helper_get_format(struct xlnx_crtc_helper *helper)
> > +{
> > + struct xlnx_crtc *crtc;
> > + u32 format = 0, tmp;
> > +
> > + list_for_each_entry(crtc, &helper->xlnx_crtcs, list) {
> > + if (crtc->get_format) {
> > + tmp = crtc->get_format(crtc);
> > + if (format && format != tmp)
> > + return 0;
> > + format = tmp;
> > + }
> > + }
> > +
> > + return format;
> > +}
> > +
> > +struct xlnx_crtc_helper *xlnx_crtc_helper_init(struct drm_device *drm)
> > +{
> > + struct xlnx_crtc_helper *helper;
> > +
> > + helper = devm_kzalloc(drm->dev, sizeof(*helper), GFP_KERNEL);
> > + if (!helper)
> > + return ERR_PTR(-ENOMEM);
> > +
> > + INIT_LIST_HEAD(&helper->xlnx_crtcs);
> > + mutex_init(&helper->lock);
> > + helper->drm = drm;
> > +
> > + return helper;
> > +}
> > +
> > +void xlnx_crtc_helper_fini(struct drm_device *drm,
> > + struct xlnx_crtc_helper *helper)
> > +{
> > + if (WARN_ON(helper->drm != drm))
> > + return;
> > +
> > + if (WARN_ON(!list_empty(&helper->xlnx_crtcs)))
> > + return;
> > +
> > + mutex_destroy(&helper->lock);
> > + devm_kfree(drm->dev, helper);
> > +}
> > +
> > +void xlnx_crtc_register(struct drm_device *drm, struct xlnx_crtc *crtc)
> > +{
> > + struct xlnx_crtc_helper *helper = xlnx_get_crtc_helper(drm);
> > +
> > + mutex_lock(&helper->lock);
> > + list_add_tail(&crtc->list, &helper->xlnx_crtcs);
> > + mutex_unlock(&helper->lock);
> > +}
> > +EXPORT_SYMBOL_GPL(xlnx_crtc_register);
> > +
> > +void xlnx_crtc_unregister(struct drm_device *drm, struct xlnx_crtc *crtc)
> > +{
> > + struct xlnx_crtc_helper *helper = xlnx_get_crtc_helper(drm);
> > +
> > + mutex_lock(&helper->lock);
> > + list_del(&crtc->list);
> > + mutex_unlock(&helper->lock);
> > +}
> > +EXPORT_SYMBOL_GPL(xlnx_crtc_unregister);
> > diff --git a/drivers/gpu/drm/xlnx/xlnx_crtc.h
> b/drivers/gpu/drm/xlnx/xlnx_crtc.h
> > new file mode 100644
> > index 0000000..1498e10
> > --- /dev/null
> > +++ b/drivers/gpu/drm/xlnx/xlnx_crtc.h
> > @@ -0,0 +1,78 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Xilinx DRM crtc header
> > + *
> > + * Copyright (C) 2017 - 2018 Xilinx, Inc.
> > + *
> > + * Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
> > + *
> > + * This software is licensed under the terms of the GNU General Public
> > + * License version 2, as published by the Free Software Foundation, and
> > + * may be copied, distributed, and modified under those terms.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + */
> > +
> > +#ifndef _XLNX_CRTC_H_
> > +#define _XLNX_CRTC_H_
> > +
> > +/**
> > + * struct xlnx_crtc - Xilinx CRTC device
> > + * @crtc: DRM CRTC device
> > + * @list: list node for Xilinx CRTC device list
> > + * @enable_vblank: Enable vblank
> > + * @disable_vblank: Disable vblank
> > + * @get_align: Get the alignment requirement of CRTC device
> > + * @get_dma_mask: Get the dma mask of CRTC device
> > + * @get_max_width: Get the maximum supported width
> > + * @get_max_height: Get the maximum supported height
> > + * @get_format: Get the current format of CRTC device
> > + */
> > +struct xlnx_crtc {
> > + struct drm_crtc crtc;
> > + struct list_head list;
> > + int (*enable_vblank)(struct xlnx_crtc *crtc);
> > + void (*disable_vblank)(struct xlnx_crtc *crtc);
> > + unsigned int (*get_align)(struct xlnx_crtc *crtc);
> > + u64 (*get_dma_mask)(struct xlnx_crtc *crtc);
> > + int (*get_max_width)(struct xlnx_crtc *crtc);
> > + int (*get_max_height)(struct xlnx_crtc *crtc);
> > + uint32_t (*get_format)(struct xlnx_crtc *crtc);
> > +};
> > +
> > +/*
> > + * Helper functions: used within Xlnx DRM
> > + */
> > +
> > +struct xlnx_crtc_helper;
> > +
> > +int xlnx_crtc_helper_enable_vblank(struct xlnx_crtc_helper *helper,
> > + unsigned int crtc_id);
> > +void xlnx_crtc_helper_disable_vblank(struct xlnx_crtc_helper *helper,
> > + unsigned int crtc_id);
> > +unsigned int xlnx_crtc_helper_get_align(struct xlnx_crtc_helper *helper);
> > +u64 xlnx_crtc_helper_get_dma_mask(struct xlnx_crtc_helper *helper);
> > +int xlnx_crtc_helper_get_max_width(struct xlnx_crtc_helper *helper);
> > +int xlnx_crtc_helper_get_max_height(struct xlnx_crtc_helper *helper);
> > +uint32_t xlnx_crtc_helper_get_format(struct xlnx_crtc_helper *helper);
> > +
> > +struct xlnx_crtc_helper *xlnx_crtc_helper_init(struct drm_device *drm);
> > +void xlnx_crtc_helper_fini(struct drm_device *drm,
> > + struct xlnx_crtc_helper *helper);
> > +
> > +/*
> > + * CRTC registration: used by other sub-driver modules
> > + */
> > +
> > +static inline struct xlnx_crtc *to_xlnx_crtc(struct drm_crtc *crtc)
> > +{
> > + return container_of(crtc, struct xlnx_crtc, crtc);
> > +}
> > +
> > +void xlnx_crtc_register(struct drm_device *drm, struct xlnx_crtc *crtc);
> > +void xlnx_crtc_unregister(struct drm_device *drm, struct xlnx_crtc
> *crtc);
> > +
> > +#endif /* _XLNX_CRTC_H_ */
> > diff --git a/drivers/gpu/drm/xlnx/xlnx_drv.c
> b/drivers/gpu/drm/xlnx/xlnx_drv.c
> > new file mode 100644
> > index 0000000..a350492
> > --- /dev/null
> > +++ b/drivers/gpu/drm/xlnx/xlnx_drv.c
> > @@ -0,0 +1,447 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Xilinx DRM KMS Driver
> > + *
> > + * Copyright (C) 2013 - 2018 Xilinx, Inc.
> > + *
> > + * Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
> > + *
> > + * This software is licensed under the terms of the GNU General Public
> > + * License version 2, as published by the Free Software Foundation, and
> > + * may be copied, distributed, and modified under those terms.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + */
> > +
> > +#include <drm/drmP.h>
> > +#include <drm/drm_atomic.h>
> > +#include <drm/drm_atomic_helper.h>
> > +#include <drm/drm_crtc_helper.h>
> > +#include <drm/drm_fb_helper.h>
> > +#include <drm/drm_gem_cma_helper.h>
> > +#include <drm/drm_of.h>
> > +
> > +#include <linux/component.h>
> > +#include <linux/device.h>
> > +#include <linux/dma-buf.h>
> > +#include <linux/module.h>
> > +#include <linux/of_graph.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/reservation.h>
> > +
> > +#include "xlnx_crtc.h"
> > +#include "xlnx_fb.h"
> > +#include "xlnx_gem.h"
> > +
> > +#define DRIVER_NAME "xlnx"
> > +#define DRIVER_DESC "Xilinx DRM KMS Driver"
> > +#define DRIVER_DATE "20130509"
> > +#define DRIVER_MAJOR 1
> > +#define DRIVER_MINOR 0
> > +
> > +static uint xlnx_fbdev_vres = 2;
> > +module_param_named(fbdev_vres, xlnx_fbdev_vres, uint, 0444);
> > +MODULE_PARM_DESC(fbdev_vres,
> > + "fbdev virtual resolution multiplier for fb (default: 2)");
> > +
> > +/**
> > + * struct xlnx_drm - Xilinx DRM private data
> > + * @drm: DRM core
> > + * @crtc: Xilinx DRM CRTC helper
> > + * @fb: DRM fb helper
> > + * @pdev: platform device
> > + * @suspend_state: atomic state for suspend / resume
> > + */
> > +struct xlnx_drm {
> > + struct drm_device *drm;
> > + struct xlnx_crtc_helper *crtc;
> > + struct drm_fb_helper *fb;
> > + struct platform_device *pdev;
> > + struct drm_atomic_state *suspend_state;
> > +};
> > +
> > +/**
> > + * xlnx_get_crtc_helper - Return the crtc helper instance
> > + * @drm: DRM device
> > + *
> > + * Return: the crtc helper instance
> > + */
> > +struct xlnx_crtc_helper *xlnx_get_crtc_helper(struct drm_device *drm)
> > +{
> > + struct xlnx_drm *xlnx_drm = drm->dev_private;
> > +
> > + return xlnx_drm->crtc;
> > +}
> > +
> > +/**
> > + * xlnx_get_align - Return the align requirement through CRTC helper
> > + * @drm: DRM device
> > + *
> > + * Return: the alignment requirement
> > + */
> > +unsigned int xlnx_get_align(struct drm_device *drm)
> > +{
> > + struct xlnx_drm *xlnx_drm = drm->dev_private;
> > +
> > + return xlnx_crtc_helper_get_align(xlnx_drm->crtc);
> > +}
> > +
> > +/**
> > + * xlnx_get_format - Return the current format of CRTC
> > + * @drm: DRM device
> > + *
> > + * Return: the current CRTC format
> > + */
> > +uint32_t xlnx_get_format(struct drm_device *drm)
> > +{
> > + struct xlnx_drm *xlnx_drm = drm->dev_private;
> > +
> > + return xlnx_crtc_helper_get_format(xlnx_drm->crtc);
> > +}
> > +
> > +static void xlnx_output_poll_changed(struct drm_device *drm)
> > +{
> > + struct xlnx_drm *xlnx_drm = drm->dev_private;
> > +
> > + if (xlnx_drm->fb)
> > + drm_fb_helper_hotplug_event(xlnx_drm->fb);
> > +}
> > +
> > +static const struct drm_mode_config_funcs xlnx_mode_config_funcs = {
> > + .fb_create = xlnx_fb_create,
> > + .output_poll_changed = xlnx_output_poll_changed,
> > + .atomic_check = drm_atomic_helper_check,
> > + .atomic_commit = drm_atomic_helper_commit,
> > +};
> > +
> > +static int xlnx_enable_vblank(struct drm_device *drm, unsigned int crtc)
> > +{
> > + struct xlnx_drm *xlnx_drm = drm->dev_private;
> > +
> > + return xlnx_crtc_helper_enable_vblank(xlnx_drm->crtc, crtc);
> > +}
> > +
> > +static void xlnx_disable_vblank(struct drm_device *drm, unsigned int
> crtc)
> > +{
> > + struct xlnx_drm *xlnx_drm = drm->dev_private;
> > +
> > + xlnx_crtc_helper_disable_vblank(xlnx_drm->crtc, crtc);
> > +}
> > +
> > +static void xlnx_mode_config_init(struct drm_device *drm)
> > +{
> > + struct xlnx_drm *xlnx_drm = drm->dev_private;
> > + struct xlnx_crtc_helper *crtc = xlnx_drm->crtc;
> > +
> > + drm->mode_config.min_width = 0;
> > + drm->mode_config.min_height = 0;
> > + drm->mode_config.max_width =
> xlnx_crtc_helper_get_max_width(crtc);
> > + drm->mode_config.max_height =
> xlnx_crtc_helper_get_max_height(crtc);
> > +}
> > +
> > +static void xlnx_lastclose(struct drm_device *drm)
> > +{
> > + struct xlnx_drm *xlnx_drm = drm->dev_private;
> > +
> > + if (xlnx_drm->fb)
> > + drm_fb_helper_restore_fbdev_mode_unlocked(xlnx_drm->fb);
> > +}
> > +
> > +static const struct file_operations xlnx_fops = {
> > + .owner = THIS_MODULE,
> > + .open = drm_open,
> > + .release = drm_release,
> > + .unlocked_ioctl = drm_ioctl,
> > + .mmap = drm_gem_cma_mmap,
> > + .poll = drm_poll,
> > + .read = drm_read,
> > +#ifdef CONFIG_COMPAT
> > + .compat_ioctl = drm_compat_ioctl,
> > +#endif
> > + .llseek = noop_llseek,
> > +};
> > +
> > +static struct drm_driver xlnx_drm_driver = {
> > + .driver_features = DRIVER_MODESET | DRIVER_GEM |
> > + DRIVER_ATOMIC | DRIVER_PRIME,
> > + .lastclose = xlnx_lastclose,
> > +
> > + .enable_vblank = xlnx_enable_vblank,
> > + .disable_vblank = xlnx_disable_vblank,
> > +
> > + .prime_handle_to_fd = drm_gem_prime_handle_to_fd,
> > + .prime_fd_to_handle = drm_gem_prime_fd_to_handle,
> > + .gem_prime_export = drm_gem_prime_export,
> > + .gem_prime_import = drm_gem_prime_import,
> > + .gem_prime_get_sg_table =
> drm_gem_cma_prime_get_sg_table,
> > + .gem_prime_import_sg_table =
> drm_gem_cma_prime_import_sg_table,
> > + .gem_prime_vmap = drm_gem_cma_prime_vmap,
> > + .gem_prime_vunmap = drm_gem_cma_prime_vunmap,
> > + .gem_prime_mmap = drm_gem_cma_prime_mmap,
> > + .gem_free_object = drm_gem_cma_free_object,
> > + .gem_vm_ops = &drm_gem_cma_vm_ops,
> > + .dumb_create = xlnx_gem_cma_dumb_create,
> > + .dumb_destroy = drm_gem_dumb_destroy,
> > +
> > + .fops = &xlnx_fops,
> > +
> > + .name = DRIVER_NAME,
> > + .desc = DRIVER_DESC,
> > + .date = DRIVER_DATE,
> > + .major = DRIVER_MAJOR,
> > + .minor = DRIVER_MINOR,
> > +};
> > +
> > +static int xlnx_bind(struct device *dev)
> > +{
> > + struct xlnx_drm *xlnx_drm;
> > + struct drm_device *drm;
> > + const struct drm_format_info *info;
> > + struct platform_device *pdev = to_platform_device(dev);
> > + int ret;
> > + u32 format;
> > +
> > + drm = drm_dev_alloc(&xlnx_drm_driver, &pdev->dev);
> > + if (IS_ERR(drm))
> > + return PTR_ERR(drm);
> > +
> > + xlnx_drm = devm_kzalloc(drm->dev, sizeof(*xlnx_drm),
> GFP_KERNEL);
> > + if (!xlnx_drm) {
> > + ret = -ENOMEM;
> > + goto err_drm;
> > + }
> > +
> > + drm_mode_config_init(drm);
> > + drm->mode_config.funcs = &xlnx_mode_config_funcs;
> > +
> > + ret = drm_vblank_init(drm, 1);
> > + if (ret) {
> > + dev_err(&pdev->dev, "failed to initialize vblank\n");
> > + goto err_xlnx_drm;
> > + }
> > +
> > + drm->irq_enabled = 1;
> > + drm->dev_private = xlnx_drm;
> > + xlnx_drm->drm = drm;
> > + drm_kms_helper_poll_init(drm);
> > + platform_set_drvdata(pdev, xlnx_drm);
> > +
> > + xlnx_drm->crtc = xlnx_crtc_helper_init(drm);
> > + if (IS_ERR(xlnx_drm->crtc)) {
> > + ret = PTR_ERR(xlnx_drm->crtc);
> > + goto err_xlnx_drm;
> > + }
> > +
> > + ret = component_bind_all(drm->dev, drm);
> > + if (ret)
> > + goto err_crtc;
> > +
> > + xlnx_mode_config_init(drm);
> > + drm_mode_config_reset(drm);
> > + dma_set_mask(drm->dev,
> xlnx_crtc_helper_get_dma_mask(xlnx_drm->crtc));
> > +
> > + format = xlnx_crtc_helper_get_format(xlnx_drm->crtc);
> > + info = drm_format_info(format);
> > + if (info && info->depth && info->cpp[0]) {
> > + unsigned int align;
> > +
> > + align = xlnx_crtc_helper_get_align(xlnx_drm->crtc);
> > + xlnx_drm->fb = xlnx_fb_init(drm, info->cpp[0] * 8, 1, align,
> > + xlnx_fbdev_vres);
> > + if (IS_ERR(xlnx_drm->fb)) {
> > + dev_err(&pdev->dev,
> > + "failed to initialize drm fb\n");
> > + xlnx_drm->fb = NULL;
> > + }
> > + } else {
> > + /* fbdev emulation is optional */
> > + dev_info(&pdev->dev, "fbdev is not initialized\n");
> > + }
> > +
> > + ret = drm_dev_register(drm, 0);
> > + if (ret < 0)
> > + goto err_fb;
> > +
> > + return 0;
> > +
> > +err_fb:
> > + if (xlnx_drm->fb)
> > + xlnx_fb_fini(xlnx_drm->fb);
> > + component_unbind_all(drm->dev, drm);
> > +err_crtc:
> > + xlnx_crtc_helper_fini(drm, xlnx_drm->crtc);
> > +err_xlnx_drm:
> > + drm_mode_config_cleanup(drm);
> > +err_drm:
> > + drm_dev_unref(drm);
> > + return ret;
> > +}
> > +
> > +static void xlnx_unbind(struct device *dev)
> > +{
> > + struct xlnx_drm *xlnx_drm = dev_get_drvdata(dev);
> > + struct drm_device *drm = xlnx_drm->drm;
> > +
> > + drm_dev_unregister(drm);
> > + if (xlnx_drm->fb)
> > + xlnx_fb_fini(xlnx_drm->fb);
> > + component_unbind_all(drm->dev, drm);
> > + xlnx_crtc_helper_fini(drm, xlnx_drm->crtc);
> > + drm_kms_helper_poll_fini(drm);
> > + drm_mode_config_cleanup(drm);
> > + drm_dev_unref(drm);
> > +}
> > +
> > +static const struct component_master_ops xlnx_master_ops = {
> > + .bind = xlnx_bind,
> > + .unbind = xlnx_unbind,
> > +};
> > +
> > +static int xlnx_of_component_probe(struct device *dev,
> > + int (*compare_of)(struct device *, void *),
> > + const struct component_master_ops *m_ops)
> > +{
> > + struct device_node *ep, *port, *remote, *parent;
> > + struct component_match *match = NULL;
> > + int i;
> > +
> > + if (!dev->of_node)
> > + return -EINVAL;
> > +
> > + for (i = 0; ; i++) {
> > + port = of_parse_phandle(dev->of_node, "ports", i);
> > + if (!port)
> > + break;
> > +
> > + parent = of_graph_get_port_parent(port);
> > + if (!of_device_is_available(parent)) {
> > + of_node_put(port);
> > + continue;
> > + }
> > +
> > + component_match_add(dev, &match, compare_of, parent);
> > + of_node_put(parent);
> > + of_node_put(port);
> > + }
> > +
> > + if (i == 0) {
> > + dev_err(dev, "missing 'ports' property\n");
> > + return -ENODEV;
> > + }
> > +
> > + if (!match) {
> > + dev_err(dev, "no available port\n");
> > + return -ENODEV;
> > + }
> > +
> > + for (i = 0; ; i++) {
> > + port = of_parse_phandle(dev->of_node, "ports", i);
> > + if (!port)
> > + break;
> > +
> > + parent = of_graph_get_port_parent(port);
> > + if (!of_device_is_available(parent)) {
> > + of_node_put(port);
> > + continue;
> > + }
> > +
> > + for_each_child_of_node(port, ep) {
> > + remote = of_graph_get_remote_port_parent(ep);
> > + if (!remote || !of_device_is_available(remote)) {
> > + of_node_put(remote);
> > + continue;
> > + } else if (!of_device_is_available(remote->parent)) {
> > + dev_warn(dev, "parent dev of %s unavailable\n",
> > + remote->full_name);
> > + of_node_put(remote);
> > + continue;
> > + }
> > + component_match_add(dev, &match, compare_of,
> remote);
> > + of_node_put(remote);
> > + }
> > + of_node_put(port);
> > + }
> > +
> > + return component_master_add_with_match(dev, m_ops, match);
> > +}
> > +
> > +static int xlnx_compare_of(struct device *dev, void *data)
> > +{
> > + return dev->of_node == data;
> > +}
> > +
> > +static int xlnx_platform_probe(struct platform_device *pdev)
> > +{
> > + return xlnx_of_component_probe(&pdev->dev, xlnx_compare_of,
> > + &xlnx_master_ops);
> > +}
> > +
> > +static int xlnx_platform_remove(struct platform_device *pdev)
> > +{
> > + component_master_del(&pdev->dev, &xlnx_master_ops);
> > + return 0;
> > +}
> > +
> > +static void xlnx_platform_shutdown(struct platform_device *pdev)
> > +{
> > + struct xlnx_drm *xlnx_drm = platform_get_drvdata(pdev);
> > +
> > + drm_put_dev(xlnx_drm->drm);
> > +}
> > +
> > +static int __maybe_unused xlnx_pm_suspend(struct device *dev)
> > +{
> > + struct xlnx_drm *xlnx_drm = dev_get_drvdata(dev);
> > + struct drm_device *drm = xlnx_drm->drm;
> > +
> > + drm_kms_helper_poll_disable(drm);
> > +
> > + xlnx_drm->suspend_state = drm_atomic_helper_suspend(drm);
> > + if (IS_ERR(xlnx_drm->suspend_state)) {
> > + drm_kms_helper_poll_enable(drm);
> > + return PTR_ERR(xlnx_drm->suspend_state);
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int __maybe_unused xlnx_pm_resume(struct device *dev)
> > +{
> > + struct xlnx_drm *xlnx_drm = dev_get_drvdata(dev);
> > + struct drm_device *drm = xlnx_drm->drm;
> > +
> > + drm_atomic_helper_resume(drm, xlnx_drm->suspend_state);
> > + drm_kms_helper_poll_enable(drm);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct dev_pm_ops xlnx_pm_ops = {
> > + SET_SYSTEM_SLEEP_PM_OPS(xlnx_pm_suspend, xlnx_pm_resume)
> > +};
> > +
> > +static const struct of_device_id xlnx_of_match[] = {
> > + { .compatible = "xlnx,display", },
> > + { /* end of table */ },
> > +};
> > +MODULE_DEVICE_TABLE(of, xlnx_of_match);
> > +
> > +static struct platform_driver xlnx_driver = {
> > + .probe = xlnx_platform_probe,
> > + .remove = xlnx_platform_remove,
> > + .shutdown = xlnx_platform_shutdown,
> > + .driver = {
> > + .name = "xlnx-drm",
> > + .pm = &xlnx_pm_ops,
> > + .of_match_table = xlnx_of_match,
> > + },
> > +};
> > +
> > +module_platform_driver(xlnx_driver);
> > +
> > +MODULE_AUTHOR("Xilinx, Inc.");
> > +MODULE_DESCRIPTION("Xilinx DRM KMS Driver");
> > +MODULE_LICENSE("GPL v2");
> > diff --git a/drivers/gpu/drm/xlnx/xlnx_drv.h
> b/drivers/gpu/drm/xlnx/xlnx_drv.h
> > new file mode 100644
> > index 0000000..8c320fd
> > --- /dev/null
> > +++ b/drivers/gpu/drm/xlnx/xlnx_drv.h
> > @@ -0,0 +1,30 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Xilinx DRM KMS Header for Xilinx
> > + *
> > + * Copyright (C) 2013 - 2018 Xilinx, Inc.
> > + *
> > + * Author: Hyun Woo Kwon <hyunk@xilinx.com>
> > + *
> > + * This software is licensed under the terms of the GNU General Public
> > + * License version 2, as published by the Free Software Foundation, and
> > + * may be copied, distributed, and modified under those terms.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + */
> > +
> > +#ifndef _XLNX_DRV_H_
> > +#define _XLNX_DRV_H_
> > +
> > +struct drm_device;
> > +struct xlnx_crtc_helper;
> > +
> > +uint32_t xlnx_get_format(struct drm_device *drm);
> > +unsigned int xlnx_get_align(struct drm_device *drm);
> > +struct xlnx_crtc_helper *xlnx_get_crtc_helper(struct drm_device *drm);
> > +struct xlnx_bridge_helper *xlnx_get_bridge_helper(struct drm_device
> *drm);
> > +
> > +#endif /* _XLNX_DRV_H_ */
> > diff --git a/drivers/gpu/drm/xlnx/xlnx_fb.c
> b/drivers/gpu/drm/xlnx/xlnx_fb.c
> > new file mode 100644
> > index 0000000..e72087d
> > --- /dev/null
> > +++ b/drivers/gpu/drm/xlnx/xlnx_fb.c
> > @@ -0,0 +1,298 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Xilinx DRM KMS Framebuffer helper
> > + *
> > + * Copyright (C) 2015 - 2018 Xilinx, Inc.
> > + *
> > + * Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
> > + *
> > + * Based on drm_fb_cma_helper.c
> > + *
> > + * Copyright (C) 2012 Analog Device Inc.
> > + *
> > + * This software is licensed under the terms of the GNU General Public
> > + * License version 2, as published by the Free Software Foundation, and
> > + * may be copied, distributed, and modified under those terms.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + */
> > +
> > +#include <drm/drmP.h>
> > +#include <drm/drm_crtc.h>
> > +#include <drm/drm_crtc_helper.h>
> > +#include <drm/drm_fb_helper.h>
> > +#include <drm/drm_gem_cma_helper.h>
> > +#include <drm/drm_gem_framebuffer_helper.h>
> > +
> > +#include "xlnx_drv.h"
> > +#include "xlnx_fb.h"
> > +
> > +#define XLNX_MAX_PLANES 4
> > +
> > +struct xlnx_fbdev {
> > + struct drm_fb_helper fb_helper;
> > + struct drm_framebuffer *fb;
> > + unsigned int align;
> > + unsigned int vres_mult;
> > +};
> > +
> > +static inline struct xlnx_fbdev *to_fbdev(struct drm_fb_helper
> *fb_helper)
> > +{
> > + return container_of(fb_helper, struct xlnx_fbdev, fb_helper);
> > +}
> > +
> > +static struct drm_framebuffer_funcs xlnx_fb_funcs = {
> > + .destroy = drm_gem_fb_destroy,
> > + .create_handle = drm_gem_fb_create_handle,
> > +};
> > +
> > +static int
> > +xlnx_fb_ioctl(struct fb_info *info, unsigned int cmd, unsigned long arg)
> > +{
> > + struct drm_fb_helper *fb_helper = info->par;
> > + unsigned int i;
> > + int ret = 0;
> > +
> > + switch (cmd) {
> > + case FBIO_WAITFORVSYNC:
> > + for (i = 0; i < fb_helper->crtc_count; i++) {
> > + struct drm_mode_set *mode_set;
> > + struct drm_crtc *crtc;
> > +
> > + mode_set = &fb_helper->crtc_info[i].mode_set;
> > + crtc = mode_set->crtc;
> > + ret = drm_crtc_vblank_get(crtc);
> > + if (!ret) {
> > + drm_crtc_wait_one_vblank(crtc);
> > + drm_crtc_vblank_put(crtc);
> > + }
> > + }
> > + return ret;
> > + default:
> > + return -ENOTTY;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static struct fb_ops xlnx_fbdev_ops = {
> > + .owner = THIS_MODULE,
> > + .fb_fillrect = sys_fillrect,
> > + .fb_copyarea = sys_copyarea,
> > + .fb_imageblit = sys_imageblit,
> > + .fb_check_var = drm_fb_helper_check_var,
> > + .fb_set_par = drm_fb_helper_set_par,
> > + .fb_blank = drm_fb_helper_blank,
> > + .fb_pan_display = drm_fb_helper_pan_display,
> > + .fb_setcmap = drm_fb_helper_setcmap,
> > + .fb_ioctl = xlnx_fb_ioctl,
> > +};
> > +
> > +/**
> > + * xlnx_fbdev_create - Create the fbdev with a framebuffer
> > + * @fb_helper: fb helper structure
> > + * @size: framebuffer size info
> > + *
> > + * This function is based on drm_fbdev_cma_create().
> > + *
> > + * Return: 0 if successful, or the error code.
> > + */
> > +static int xlnx_fbdev_create(struct drm_fb_helper *fb_helper,
> > + struct drm_fb_helper_surface_size *size)
> > +{
> > + struct xlnx_fbdev *fbdev = to_fbdev(fb_helper);
> > + struct drm_device *drm = fb_helper->dev;
> > + struct drm_gem_cma_object *obj;
> > + struct drm_framebuffer *fb;
> > + unsigned int bytes_per_pixel;
> > + unsigned long offset;
> > + struct fb_info *fbi;
> > + size_t bytes;
> > + int ret;
> > +
> > + dev_dbg(drm->dev, "surface width(%d), height(%d) and bpp(%d)\n",
> > + size->surface_width, size->surface_height, size->surface_bpp);
> > +
> > + size->surface_height *= fbdev->vres_mult;
> > + bytes_per_pixel = DIV_ROUND_UP(size->surface_bpp, 8);
> > + bytes = ALIGN(size->surface_width * bytes_per_pixel, fbdev->align);
> > + bytes *= size->surface_height;
> > +
> > + obj = drm_gem_cma_create(drm, bytes);
> > + if (IS_ERR(obj))
> > + return PTR_ERR(obj);
> > +
> > + fbi = framebuffer_alloc(0, drm->dev);
> > + if (!fbi) {
> > + dev_err(drm->dev, "Failed to allocate framebuffer info.\n");
> > + ret = -ENOMEM;
> > + goto err_drm_gem_cma_free_object;
> > + }
> > +
> > + fbdev->fb = drm_gem_fbdev_fb_create(drm, size, fbdev->align,
> &obj->base,
> > + &xlnx_fb_funcs);
> > + if (IS_ERR(fbdev->fb)) {
> > + dev_err(drm->dev, "Failed to allocate DRM framebuffer.\n");
> > + ret = PTR_ERR(fbdev->fb);
> > + goto err_framebuffer_release;
> > + }
> > +
> > + fb = fbdev->fb;
> > + fb_helper->fb = fb;
> > + fb_helper->fbdev = fbi;
> > + fbi->par = fb_helper;
> > + fbi->flags = FBINFO_FLAG_DEFAULT;
> > + fbi->fbops = &xlnx_fbdev_ops;
> > +
> > + ret = fb_alloc_cmap(&fbi->cmap, 256, 0);
> > + if (ret) {
> > + dev_err(drm->dev, "Failed to allocate color map.\n");
> > + goto err_fb_destroy;
> > + }
> > +
> > + drm_fb_helper_fill_fix(fbi, fb->pitches[0], fb->format->depth);
> > + drm_fb_helper_fill_var(fbi, fb_helper, fb->width, fb->height);
> > + fbi->var.yres = fb->height / fbdev->vres_mult;
> > +
> > + offset = fbi->var.xoffset * bytes_per_pixel;
> > + offset += fbi->var.yoffset * fb->pitches[0];
> > +
> > + drm->mode_config.fb_base = (resource_size_t)obj->paddr;
> > + fbi->screen_base = (char __iomem *)(obj->vaddr + offset);
> > + fbi->fix.smem_start = (unsigned long)(obj->paddr + offset);
> > + fbi->screen_size = bytes;
> > + fbi->fix.smem_len = bytes;
> > +
> > + return 0;
> > +
> > +err_fb_destroy:
> > + drm_framebuffer_unregister_private(fb);
> > + drm_gem_fb_destroy(fb);
> > +err_framebuffer_release:
> > + framebuffer_release(fbi);
> > +err_drm_gem_cma_free_object:
> > + drm_gem_cma_free_object(&obj->base);
> > + return ret;
> > +}
> > +
> > +static struct drm_fb_helper_funcs xlnx_fb_helper_funcs = {
> > + .fb_probe = xlnx_fbdev_create,
> > +};
> > +
> > +/**
> > + * xlnx_fb_init - Allocate and initializes the Xilinx framebuffer
> > + * @drm: DRM device
> > + * @preferred_bpp: preferred bits per pixel for the device
> > + * @max_conn_count: maximum number of connectors
> > + * @align: alignment value for pitch
> > + * @vres_mult: multiplier for virtual resolution
> > + *
> > + * This function is based on drm_fbdev_cma_init().
> > + *
> > + * Return: a newly allocated drm_fb_helper struct or a ERR_PTR.
> > + */
> > +struct drm_fb_helper *
> > +xlnx_fb_init(struct drm_device *drm, int preferred_bpp,
> > + unsigned int max_conn_count, unsigned int align,
> > + unsigned int vres_mult)
> > +{
> > + struct xlnx_fbdev *fbdev;
> > + struct drm_fb_helper *fb_helper;
> > + int ret;
> > +
> > + fbdev = kzalloc(sizeof(*fbdev), GFP_KERNEL);
> > + if (!fbdev)
> > + return ERR_PTR(-ENOMEM);
> > +
> > + fbdev->vres_mult = vres_mult;
> > + fbdev->align = align;
> > + fb_helper = &fbdev->fb_helper;
> > + drm_fb_helper_prepare(drm, fb_helper, &xlnx_fb_helper_funcs);
> > +
> > + ret = drm_fb_helper_init(drm, fb_helper, max_conn_count);
> > + if (ret < 0) {
> > + dev_err(drm->dev, "Failed to initialize drm fb helper.\n");
> > + goto err_free;
> > + }
> > +
> > + ret = drm_fb_helper_single_add_all_connectors(fb_helper);
> > + if (ret < 0) {
> > + dev_err(drm->dev, "Failed to add connectors.\n");
> > + goto err_drm_fb_helper_fini;
> > + }
> > +
> > + ret = drm_fb_helper_initial_config(fb_helper, preferred_bpp);
> > + if (ret < 0) {
> > + dev_err(drm->dev, "Failed to set initial hw configuration.\n");
> > + goto err_drm_fb_helper_fini;
> > + }
> > +
> > + return fb_helper;
> > +
> > +err_drm_fb_helper_fini:
> > + drm_fb_helper_fini(fb_helper);
> > +err_free:
> > + kfree(fbdev);
> > + return ERR_PTR(ret);
> > +}
> > +
> > +/**
> > + * xlnx_fbdev_defio_fini - Free the defio fb
> > + * @fbi: fb_info struct
> > + *
> > + * This function is based on drm_fbdev_cma_defio_fini().
> > + */
> > +static void xlnx_fbdev_defio_fini(struct fb_info *fbi)
> > +{
> > + if (!fbi->fbdefio)
> > + return;
> > +
> > + fb_deferred_io_cleanup(fbi);
> > + kfree(fbi->fbdefio);
> > + kfree(fbi->fbops);
> > +}
> > +
> > +/**
> > + * xlnx_fbdev_fini - Free the Xilinx framebuffer
> > + * @fb_helper: drm_fb_helper struct
> > + *
> > + * This function is based on drm_fbdev_cma_fini().
> > + */
> > +void xlnx_fb_fini(struct drm_fb_helper *fb_helper)
> > +{
> > + struct xlnx_fbdev *fbdev = to_fbdev(fb_helper);
> > +
> > + drm_fb_helper_unregister_fbi(&fbdev->fb_helper);
> > + if (fbdev->fb_helper.fbdev)
> > + xlnx_fbdev_defio_fini(fbdev->fb_helper.fbdev);
> > +
> > + if (fbdev->fb_helper.fb)
> > + drm_framebuffer_remove(fbdev->fb_helper.fb);
> > +
> > + drm_fb_helper_fini(&fbdev->fb_helper);
> > + kfree(fbdev);
> > +}
> > +
> > +/**
> > + * xlnx_fb_create - (struct drm_mode_config_funcs *)->fb_create
> callback
> > + * @drm: DRM device
> > + * @file_priv: drm file private data
> > + * @mode_cmd: mode command for fb creation
> > + *
> > + * This functions creates a drm_framebuffer with xlnx_fb_funcs for given
> mode
> > + * @mode_cmd. This functions is intended to be used for the fb_create
> callback
> > + * function of drm_mode_config_funcs.
> > + *
> > + * Return: a drm_framebuffer object if successful, or
> > + * ERR_PTR from drm_gem_fb_create_with_funcs().
> > + */
> > +struct drm_framebuffer *
> > +xlnx_fb_create(struct drm_device *drm, struct drm_file *file_priv,
> > + const struct drm_mode_fb_cmd2 *mode_cmd)
> > +{
> > + return drm_gem_fb_create_with_funcs(drm, file_priv, mode_cmd,
> > + &xlnx_fb_funcs);
> > +}
> > diff --git a/drivers/gpu/drm/xlnx/xlnx_fb.h
> b/drivers/gpu/drm/xlnx/xlnx_fb.h
> > new file mode 100644
> > index 0000000..6efc985
> > --- /dev/null
> > +++ b/drivers/gpu/drm/xlnx/xlnx_fb.h
> > @@ -0,0 +1,33 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Xilinx DRM KMS Framebuffer helper header
> > + *
> > + * Copyright (C) 2015 - 2018 Xilinx, Inc.
> > + *
> > + * Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
> > + *
> > + * This software is licensed under the terms of the GNU General Public
> > + * License version 2, as published by the Free Software Foundation, and
> > + * may be copied, distributed, and modified under those terms.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + */
> > +
> > +#ifndef _XLNX_FB_H_
> > +#define _XLNX_FB_H_
> > +
> > +struct drm_fb_helper;
> > +
> > +struct drm_framebuffer *
> > +xlnx_fb_create(struct drm_device *drm, struct drm_file *file_priv,
> > + const struct drm_mode_fb_cmd2 *mode_cmd);
> > +struct drm_fb_helper *
> > +xlnx_fb_init(struct drm_device *drm, int preferred_bpp,
> > + unsigned int max_conn_count, unsigned int align,
> > + unsigned int vres_mult);
> > +void xlnx_fb_fini(struct drm_fb_helper *fb_helper);
> > +
> > +#endif /* _XLNX_FB_H_ */
> > diff --git a/drivers/gpu/drm/xlnx/xlnx_gem.c
> b/drivers/gpu/drm/xlnx/xlnx_gem.c
> > new file mode 100644
> > index 0000000..4a5d533
> > --- /dev/null
> > +++ b/drivers/gpu/drm/xlnx/xlnx_gem.c
> > @@ -0,0 +1,47 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Xilinx DRM KMS GEM helper
> > + *
> > + * Copyright (C) 2015 - 2018 Xilinx, Inc.
> > + *
> > + * Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
> > + *
> > + * This software is licensed under the terms of the GNU General Public
> > + * License version 2, as published by the Free Software Foundation, and
> > + * may be copied, distributed, and modified under those terms.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + */
> > +
> > +#include <drm/drmP.h>
> > +#include <drm/drm_gem_cma_helper.h>
> > +
> > +#include "xlnx_drv.h"
> > +#include "xlnx_gem.h"
> > +
> > +/*
> > + * xlnx_gem_cma_dumb_create - (struct drm_driver)->dumb_create
> callback
> > + * @file_priv: drm_file object
> > + * @drm: DRM object
> > + * @args: info for dumb scanout buffer creation
> > + *
> > + * This function is for dumb_create callback of drm_driver struct. Simply
> > + * it wraps around drm_gem_cma_dumb_create() and sets the pitch
> value
> > + * by retrieving the value from the device.
> > + *
> > + * Return: The return value from drm_gem_cma_dumb_create()
> > + */
> > +int xlnx_gem_cma_dumb_create(struct drm_file *file_priv, struct
> drm_device *drm,
> > + struct drm_mode_create_dumb *args)
> > +{
> > + int pitch = DIV_ROUND_UP(args->width * args->bpp, 8);
> > + unsigned int align = xlnx_get_align(drm);
> > +
> > + if (!args->pitch || !IS_ALIGNED(args->pitch, align))
> > + args->pitch = ALIGN(pitch, align);
> > +
> > + return drm_gem_cma_dumb_create_internal(file_priv, drm, args);
> > +}
> > diff --git a/drivers/gpu/drm/xlnx/xlnx_gem.h
> b/drivers/gpu/drm/xlnx/xlnx_gem.h
> > new file mode 100644
> > index 0000000..f380de9
> > --- /dev/null
> > +++ b/drivers/gpu/drm/xlnx/xlnx_gem.h
> > @@ -0,0 +1,26 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Xilinx DRM KMS GEM helper header
> > + *
> > + * Copyright (C) 2015 - 2018 Xilinx, Inc.
> > + *
> > + * Author: Hyun Woo Kwon <hyun.kwon@xilinx.com>
> > + *
> > + * This software is licensed under the terms of the GNU General Public
> > + * License version 2, as published by the Free Software Foundation, and
> > + * may be copied, distributed, and modified under those terms.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + */
> > +
> > +#ifndef _XLNX_GEM_H_
> > +#define _XLNX_GEM_H_
> > +
> > +int xlnx_gem_cma_dumb_create(struct drm_file *file_priv,
> > + struct drm_device *drm,
> > + struct drm_mode_create_dumb *args);
> > +
> > +#endif /* _XLNX_GEM_H_ */
> > --
> > 2.7.4
> >
> > This email and any attachments are intended for the sole use of the
> named recipient(s) and contain(s) confidential information that may be
> proprietary, privileged or copyrighted under applicable law. If you are not
> the intended recipient, do not read, copy, or forward this email message or
> any attachments. Delete this email message and any attachments
> immediately.
>
> --
> Daniel Vetter
> Software Engineer, Intel Corporation
> http://blog.ffwll.ch
^ permalink raw reply [flat|nested] 17+ messages in thread
end of thread, other threads:[~2018-01-26 1:36 UTC | newest]
Thread overview: 17+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-01-16 1:57 [PATCH v3 1/8] dt-bindings: display: xlnx: Add bindings for Xilinx display pipeline Hyun Kwon
[not found] ` <1516067831-11382-1-git-send-email-hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
2018-01-16 1:57 ` [PATCH v3 2/8] drm: xlnx: Xilinx DRM KMS driver Hyun Kwon
[not found] ` <1516067831-11382-2-git-send-email-hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
2018-01-17 8:11 ` Daniel Vetter
2018-01-17 8:20 ` Daniel Vetter
2018-01-19 23:33 ` Rob Herring
[not found] ` <20180117082028.GC2759-dv86pmgwkMBes7Z6vYuT8azUEOm+Xw19@public.gmane.org>
2018-01-26 1:36 ` Hyun Kwon
2018-01-16 1:57 ` [PATCH v3 3/8] dt-bindings: display: xlnx: Add ZynqMP DP subsystem bindings Hyun Kwon
[not found] ` <1516067831-11382-3-git-send-email-hyun.kwon-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
2018-01-20 0:31 ` Rob Herring
2018-01-20 2:22 ` Hyun Kwon
2018-01-22 14:36 ` Rob Herring
2018-01-16 1:57 ` [PATCH v3 4/8] drm: xlnx: DRM KMS driver for Xilinx ZynqMP DP subsystem display Hyun Kwon
2018-01-16 1:57 ` [PATCH v3 5/8] drm: xlnx: DRM KMS driver for Xilinx ZynqMP DisplayPort Hyun Kwon
2018-01-16 1:57 ` [PATCH v3 6/8] drm: xlnx: ZynqMP DP subsystem DRM KMS driver Hyun Kwon
2018-01-16 1:57 ` [PATCH v3 7/8] drm: xlnx: zynqmp_disp: Add drm properties Hyun Kwon
2018-01-16 1:57 ` [PATCH v3 8/8] drm: xlnx: zynqmp_dp: " Hyun Kwon
2018-01-19 23:32 ` [PATCH v3 1/8] dt-bindings: display: xlnx: Add bindings for Xilinx display pipeline Rob Herring
2018-01-20 2:22 ` Hyun Kwon
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).